Chapter 11 Logic Gate Circuitry. 2 Basic Logic Families TTL – transistor-transistor logic based on bipolar transistors. CMOS – complementary metal-oxide.
Post on 02-Jan-2016
242 Views
Preview:
Transcript
Chapter 11
Logic Gate Circuitry
2
Basic Logic Families• TTL – transistor-transistor logic based
on bipolar transistors.• CMOS – complementary metal-oxide
semiconductor logic based on metal-oxide-semiconductor field effect transistors (MOSFETs).
• ECL – emitter coupled logic based on bipolar transistors.
3
General Characteristics of Basic Logic Families
• CMOS consumes very little power, has excellent noise immunity, and is used with a wide range of voltages.
• TTL can drive more current and uses more power than CMOS.
• ECL is fast, with poor noise immunity and high power consumption.
4
Logic Subfamilies
• Both TTL and CMOS are available in a wide range of subfamilies.
• In subfamilies, the part designations for identical logic functions remain the same, but the electrical characteristics are different.
5
Examples of TTL Subfamilies
TTL
Part
Number
Logic
Family
74LS00 Low-power Schottky TTL
74ALS00 Advanced low-power Schottky
74F00 Fast TTL
6
Examples of CMOS Subfamilies
CMOS
Part
Number
Logic
Family
74HC00 High speed CMOS
74HCT00 High-speed CMOS – TTL compatible
74VX00 Low-voltage CMOS
7
Input/Output Voltage and Current Definitions
• Values for any gate are designated with two subscripts:– The first subscript indicates an input or
output value– The second subscript indicates the logic
level
8
Input/Output Voltage Designations
• VOL – the logic LOW output voltage.
• VOH – the logic HIGH output voltage.
• VIL – the logic LOW input voltage.
• VIH – the logic HIGH input voltage.
9
Input/Output Voltage Designations
10
Input/Output Current Designations
• IOL – the logic LOW output current.
• IOH – the logic HIGH output current.
• IIL – the logic LOW input current.
• IIH – the logic HIGH input current.
11
Input/Output Current Designations
12
Part Designation• Typically 54XXYY or 74XXYY.• 54 series is manufactured to military
specifications.• 74 series is manufactured to commercial
specifications.• XX is the subfamily designation.• YY is the part designation.
13
Data Sheets
• Use the appropriate maximum or minimum parameters in design.
• Typical values should be considered “information only.”
• Refer to Figure 11.3 in the textbook.
14
Propagation Delay
• The time required for the output of a digital circuit to change states after a change at one or more of its inputs.
• Largely due to charging and discharging of capacitances inherent in the gate or flip-flop switching transistors.
15
Propagation Delay Definitions
• tpHL is the propagation delay when the device output changes from HIGH to LOW.
• tpLH is the propagation delay when the device output changes from LOW to HIGH.
16
Propagation Delay Definitions
17
Propagation Delay Definitions
18
Propagation Delay Factors
• Varies with operating conditions.
• Particularly affected by temperature and the power supply voltage.
19
Propagation Delay of 74XX00 Gates
74F00* 74AS00 74ALS00 74HC00** 74HCT00***tpLH 6nS 4.5nS 11nS 15nS 22nS
tpHL 5.3nS 4nS 8nS 15nS 22nS
* Temperature range (74F00): 0OC to 70OC.
**VCC = 4.5V, TEMPERATURE RANGE (74HC00): -55OC TO 25OC.
***VCC = 5.5V, TEMPERATURE RANGE (74HCT00): 25OC.
20
Propagation Delay in Logic Circuits
• Sum of the delays in the input-to-output paths.
• Delays that do not affect the circuit output are ignored.
21
Propagation Delay in Logic Circuits
22
Input Data to Clock Timing
• Setup time (tsu) – the time required for the synchronous inputs of a flip-flop to be stable before the clock active edge.
• Hold time (th) – the time that the synchronous inputs of a flip-flop must remain stable after the clock active edge.
23
Input Data to Clock Timing
24
Clock Timing Requirement – 1
• Pulse width (tw) is the minimum time required for an active-level pulse applied to a input.
• Values are measured from the midpoint of the leading edge of the pulse to the midpoint of the trailing edge.
PRECLRCLK, or ,
25
Clock Timing Requirement – 1
26
Clock Timing Requirement – 2
• Recovery time (trec) is the time from the midpoint of the trailing edge of a pulse to the midpoint of an active edge CLK edge (See Table 11.4 in the textbook).
• For a flip-flop, the propagation delay due to the clock is defined as the delay measured from the active edge of the clock to a corresponding change in Q.
27
Clock Timing Requirement – 3
28
Fanout
• The number of gates that a logic gate is capable of driving without possible logic error.
• Limited by the maximum current a gate can supply in a given logic state versus the current requirements of the load.
29
Fanout Definitions
• Driving gate is the gate whose output supplies current to the inputs of other gates.
• Load gate is a gate whose input current is supplied by the output of another gate.
30
Fanout Definitions
31
Current Output Definitions
• Sourcing means that the current flows out of the terminal.
• Sinking means that the current flows into the terminal.
32
Current Output Definitions
33
Driving Gate Fanout
• May be different for sourcing and sinking.
IH
OHH
L
I
In
I
In
IL
OL
34
Fanout Example for 74LS00
• IOL = 8 mAIIL = –0.4 mAnL = 20
• IOH = –0.4 mAIIH = 20 μAnH = 20
35
Current Designations
• Sourcing currents are designated as negative.
• Sinking currents are designated as positive.
• Sign is disregarded in fanout calculations.
36
Exceeding Fanout
• Output voltage VOL increases with increasing sink current.
• Output voltage VOH decreases with increasing source current.
• A greater load in either state takes the output voltage further away from its nominal value.
37
Power Dissipation
• The measure of energy used over time by electronic logic gates.
• The product of the voltage and current required for the operation of the circuit.
38
Power Dissipation in TTL Devices
• PD = VCCICC.
• VCC = power supply voltage.
• ICC = current used.
• In general, ICC = (ICCH + ICCL)/2.
39
Power Dissipation in TTL Devices
40
ICCL and ICCH
• ICCL is the current drawn from the supply when all outputs are LOW.
• ICCH the current drawn form from the supply when all outputs are HIGH.
41
Power Dissipation in CMOS Devices
• PD = VCCIT.
• VCC = power supply voltage.
• IT = quiescent + dynamic supply current.
42
CMOS Quiescent vs. Dynamic Current
• Quiescent current flows when the gate is in a steady state and is usually small.
• Dynamic current flows when the gate is changing state.
• The faster a CMOS gate switches, the more current (and the more power) it requires.
43
Power Dissipation of TTL vs. CMOS
• Power dissipation in TTL is independent of frequency.
• Power dissipation in CMOS is dependent on frequency.
• In slow circuits (< 1 MHz), CMOS is generally superior.
44
Noise
• Unwanted electrical signals.• Induced by electromagnetic fields by
such sources as motors, fluorescent lights, high-frequency circuits, and cosmic rays.
• Can cause erroneous operation of a digital circuit.
45
Noise Margin
• A certain amount of tolerance is built into digital devices to tolerate noise.
• Noise margin is required for both LOW and HIGH inputs (See Figure 11.15 in the textbook).
46
Noise Margin for 74LS04
• HIGH state: VNH = VOH – VIH = 3.0 V – 2.0 V VNH = 1.0 V.
• LOW state: VNL = VIL – VOL = 0.8 V – 0.5 V VNL = 0.3 V.
47
Noise Margin for 74HC00A
• HIGH state: VNH = VOH – VIH = 3.98 V – 3.15 V VNH = 0.63 V.
• LOW state: VNL = VIL – VOL = 1.35 V – 0.26 V VNL = 1.09 V.
48
Interfacing TTL and CMOS
• An extension of fanout and noise margin calculations.
• Requires knowledge of input and output voltages and currents for the gates in question.
• Refer to Table 11.5 in the textbook.
49
High-Speed CMOS Driving 74LS
• In general, the 74HC family satisfies the input voltage requirements of the 74LS family.
• In general, the 74HC family can drive the 74LS family directly, with a fanout of 10.
50
74LS Driving 74HC
• In general, the 74LS family satisfies the LOW-state criterion, but cannot guarantee sufficient output voltage in the HIGH state.
• Requires a pull-up resistor on the output to ensure sufficient HIGH-state voltage at the 74HC input.
51
74LS Driving 74HCT
• The 74HCT family has been designed to be compatible with TTL outputs.
• The 74LS family can drive the 74HCT family directly.
52
74LS Driving 74HCT
53
74LS Driving Low-Voltage CMOS
• Low-voltage CMOS families, such as 74LVX and 74LCX, can interface directly with TTL outputs using 3.0-V to 3.3-V power supplies.
• TTL outputs using a 5.0-V power supply must be buffered to translate the TTL level down to an appropriate value.
54
74LS Driving Low-Voltage CMOS
55
TTL Gates Internal Circuitry
• Uses the bipolar junction transistor.• The transistors used are in one of two modes:
cutoff or saturation.• In cutoff mode, the transistor acts as an open
switch.• In saturation, the transistor acts as a closed
switch.
56
TTL Gates Internal Circuitry
57
Bipolar Transistor Characteristics
Cutoff Active SaturationI C 0
V CE Open cct. >0.8 V 0.2 V - 0.7 V
V BE <0.6 V 0.6 V - 0.7 V
BβI BβI
v7.0
58
Open-Collector Outputs
• A circuit that has LOW-state output circuitry, but no HIGH-state output circuitry.
• Requires an external pull-up resistor to enable the output to produce a HIGH-state.
59
Advantages of Open-Collector Outputs
• Allows the outputs of multiple gates to be directly connected.– – Called wired-AND.
• Can produce voltage levels in excess of 5 V.
• Can drive high-input current devices.
60
Advantages of Open-Collector Outputs
61
Open-Collector Applications
• Wired-AND – the outputs of logic gates are wired together.
• The wired-AND logical equivalent of combining the outputs in an AND function.
62
Open-Collector Applications
63
Open-Collector Applications
64
TTL Inputs
• LOW inputs allow current to flow from the gate VCC to the input.
• HIGH inputs cause current to flow to the phase splitter transistor.
• Open (floating) inputs act as a logic HIGH, but are unstable and vulnerable to noise.
65
Totem Pole Outputs
• The standard TTL output configuration with a HIGH output and a LOW output transistor, only one of which is active at any time.
• A phase splitter transistor controls which transistor is active.
66
Totem Pole Outputs
67
Advantages of Totem Pole Configuration
• Changes state faster than open-collector outputs.
• No external components are required.
68
Totem Pole Switching Noise
• Caused by one output transistor turning off slower than the other turns on.
• Briefly shorts VCC to ground.
• Prevented with use of decoupling capacitors.
69
Decoupling Capacitors
• Usually about 0.1 µF placed between VCC and ground on the chips to be decoupled.
• Acts as a low-impedance path to ground for high frequency noise.
• Usually require one per chip.
70
Decoupling Capacitors
71
Decoupling Capacitors
72
Decoupling Capacitors
73
Connecting Totem Pole Outputs
• Outputs must never be connected together.
• Connecting outputs causes excessively high currents to flow.
• Outputs will eventually be damaged.
74
Connecting Totem Pole Outputs
75
Tristate Outputs
• A configuration where there are three possible output states: logic HIGH, logic LOW, and a high-impedance state (Z).
• Created with circuitry to cut off both totem pole output transistors.
76
Tristate Inverter Truth Table
G A Y A Y0 0 Hi-Z 0 0 10 1 Hi-Z 0 1 01 0 1 1 0 Hi-Z1 1 0 1 1 Hi-Z
G
77
Other Basic TTL Gates
• NOR gates require an individual transistor for each input.
• AND and OR gates are based on NAND and NOR gates and require an extra inverter stage.
78
MOSFET Types
• Depletion-mode.• Enhancement-mode:
– n-channel– p-channel
• CMOS (complementary) constructed from both n- and p-channel transistors.
79
MOSFET Types
80
MOSFET BIAS Requirements
• Operates in two modes:• Cutoff – acts as a very high impedance
between the drain and the source.• Ohmic – equivalent of saturation. Acts
like a relatively low resistance between the drain and the source.
81
MOSFET BIAS Requirements
82
MOSFET BIAS Requirements
83
CMOS Inverter
• Depends on the biasing of the complementary transistors Q1 and Q2.
• Q1 and Q2 are always in opposite states.
• When Q1 is ON, Q2 is OFF.
84
CMOS Inverter
85
CMOS Transmission Gate
• Behaves like an analog switch.
• Conducts in both directions.
• Used to enable or inhibit time-varying analog signals.– When CONTROL = 1, conduction occurs
– When CONTROL = 0, conduction is inhibited
86
CMOS Transmission Gate
87
Schottky Family TTL
• Uses a Schottky barrier diode to create a Schottky transistor.
• Allows transistors to avoid deep saturation and to switch faster.
• Uses less power than standard TTL.
88
Speed-Power Product
• One measure of logic circuit efficiency.
• Uses worst-case values of propagation delay and power dissipation per gate.
• Expressed in picojoules (pJ).
• See Table 11.15 in the textbook.
89
CMOS Logic Families
• Metal-Gate CMOS (rarely used).
• High-Speed CMOS.
• Advanced High-Speed CMOS.
• Low-Voltage CMOS.
• See Table 11.16 in the textbook.
top related