Marshall Mix Design
CIVL 3137 46
Asphalt Concrete Properties
Stability
Workability
Skid Resistance
Durability
Stripping
Fatigue Cracking
Thermal Cracking
Bleeding
CIVL 3137 47
Stability
The ability to withstand traffic loads withoutdistortion or deflection, especially at highertemperatures.
To get good stability, use strong, rough, dense-graded, cubical aggregatewith just enough binder to coat the aggregate particles. Excess asphaltcement lubricates the aggregate particles and lets them slide past eachother more easily (which reduces stability). But a thick asphalt coatingprovides good flexibility to resist cracking, which is desirable. Hmmm…
CIVL 3137 48
Workability
The ability to be placed and compacted withreasonable effort and without segregation ofthe coarse aggregate.
Too much asphalt cement makes the mix tender. Too little asphalt cementmakes it hard to compact. Too much natural sand can also make the mixtender because natural sand has smooth, round grains. Hmmm…
CIVL 3137 49
Skid Resistance
Proper traction in wet and dry conditions.
To get good skid resistance, use smaller aggregate so there are lots ofcontact points, use hard aggregate that doesn’t polish and make sure youhave enough air voids to prevent bleeding.
Some states now use an open-graded friction course (OGFC) that allowswater to drain to the sides of the pavement, eliminating hydroplaning. ButOGFC is not very durable because of the open pores. Hmmm…
CIVL 3137 50
Durability
The ability to resist aggregate breakdown dueto wetting and drying, freezing and thawing,or excessive inter-particle forces.
To get good durability, use strong, tough, nonporous aggregate andenough asphalt cement to completely coat all of the aggregate particles(to keep them dry) and fill all of the voids between particles (to slow theoxidation of the asphalt cement). But this reduces stability. Hmmm…
CIVL 3137 51
Stripping
Separation of the asphalt cement coating fromthe aggregate due to water getting betweenthe asphalt and the aggregate.
To reduce stripping, use clean, rough, hydrophobic aggregate and addenough asphalt cement to provide a thick coating of asphalt on everyaggregate particle. This improves durability but decreases stability.
CIVL 3137 52
Bleeding
The migration of asphalt cement to the surfaceof the pavement under wheel loads, especiallyat higher temperatures.
To prevent bleeding, incorporate enough air voids so the asphalt cancompress by closing air voids rather than by squeezing asphalt cementout from between the aggregate particles.
CIVL 3137 53
Fatigue Cracking
Cracking resulting from repeated flexure ofthe asphalt concrete due to traffic loads.
To minimize fatigue cracking, use the proper asphalt cement grade andhave a thick asphalt cement coating to make the concrete flexible. Thisimproves durability but decreases stability.
CIVL 3137 54
Thermal Cracking
Cracking that results from an inability toacclimate to a sudden drop in temperature.
To minimize thermal cracking, use the proper asphalt cement grade.
CIVL 3137 55
Mix Design Basics
The right grade of asphalt cementRelates to fatigue cracking, thermal cracking, stability
The right type of aggregateRelates to stability, durability, stripping, skid resistance
The right mix volumetricsRelates to stability, durability, stripping, bleeding, skid resistance
CIVL 3137 56
Right Type of Asphalt Cement
767064585246-4-10-16-22-28
PG70-22
Reliability = (1.00)(0.98) = 98%
~0% ~2%~100% ~98%
Lowest 1-dayPavement
Temperature
Highest 7-dayPavement
Temperature
CIVL 3137 57
The Right Type of Aggregate
1. Strong and Durable2. No Deleterious Substances3. Cubical (Angular and Equidimensional)4. Low Porosity5. Clean, Rough, and Hydrophobic6. Hard7. Dense-Graded
CIVL 3137 58
The Right Mix Volumetrics
BleedingLow stabilityTender mix
StrippingLow durability
Fatigue cracking
CIVL 3137 59
Marshall Mix Design
Bruce Marshall, Mississippi Highway Department
Marshall Mix Design Steps
1. Create aggregate blend to meet gradation specifications.
2. Establish mixing and compaction temperatures from the viscosity-temperature chart.
3. Compact three specimens at each of five asphalt contents spanning the expected optimum asphalt content.
4. Determine the relative density of each specimen and the mix volumetrics (mb, VTM, VMA, VFA).
5. Measure the performance properties of the each specimen at 60ºC (140ºF).
CIVL 3137 60
CIVL 3137 61
Marshall Specimens
Traffic Blows / Side
Light 35
Medium 50
Heavy 75
10#18"
Make 3 specimens at each of5 different asphalt contents
CIVL 3137 62
Marshall Hammer
Mold
Hammer
CIVL 3137 70
Stability and Flow Test
140oF
flow
stability
deflection(0.01 in)
load(lbs)
CIVL 3137 71
Stability and Flow Test
CIVL 3137 72
Marshall Mix Design
159
160
161
162
163
164
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Uni
t Wei
ght (
pcf)
CIVL 3137 73
1500
1600
1700
1800
1900
2000
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Mar
shal
l Sta
bilit
y (lb
s)
Marshall Mix Design
CIVL 3137 74
1
2
3
4
5
6
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Air
Voi
ds (%
)
Marshall Mix Design
CIVL 3137 75
0
5
10
15
20
25
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Flow
Marshall Mix Design
CIVL 3137 76
50
60
70
80
90
100
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Void
s Fill
ed w
ith A
spha
lt (%
)
Marshall Mix Design
CIVL 3137 77
Marshall Mix Design
%7.43
3.47.41.5AC
MaximumDensity
MaximumStability
4% AirVoids
(The Asphalt Institute Procedure)
CIVL 3137 78
Marshall Mix Design
5.1
AC 4.7
4.3
4.3%1
MaximumDensity
MaximumStability
4% AirVoids
(The NAPA Procedure)
ThisiswhatTDOTuses
CIVL 3137 79
Marshall Mix Design(Asphalt Institute Criteria)
Criteria Min. Max. Min. Max. Min. Max.
Number of Blows
Stability (lbs) 500 750 1500
Flow 8 20 8 18 8 16
Air Voids (%) 3 5 3 5 3 5
VMA (%) See Next Slide
Light Traffic Medium Traffic Heavy Traffic
35 50 75
16 14
1800TDOTuses2000
18
750 1200
CIVL 3137 80
VMA CriteriaM
inim
um V
MA
(%)
10
Nominal Maximum Particle Size
20
30
40
50
2"1½"1"¾"½"4 3/8"840
Deficient in either
asphalt or air voids
(Assuming 4% Design Air Voids)
CIVL 3137 81
VMA CriteriaM
inim
um V
MA
(%)
10
Nominal Maximum Particle Size
20
30
40
50
2"1½"1"¾"½"4 3/8"840
Deficient in either
asphalt or air voids
(Assuming 5% Design Air Voids)
1%
CIVL 3137 82
VMA CriteriaM
inim
um V
MA
(%)
10
Nominal Maximum Particle Size
20
30
40
50
2"1½"1"¾"½"4 3/8"840
Deficient in either
asphalt or air voids
(Assuming 3% Design Air Voids)
1%
CIVL 3137 83
1500
1600
1700
1800
1900
2000
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Mar
shal
l Sta
bilit
y (lb
s)
Marshall Mix Design
CIVL 3137 84
0
5
10
15
20
25
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Flow
Marshall Mix Design
CIVL 3137 85
1
2
3
4
5
6
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Air
Voi
ds (%
)
Marshall Mix Design
CIVL 3137 86
50
60
70
80
90
100
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
Void
s Fill
ed w
ith A
spha
lt (%
)
Marshall Mix Design
CIVL 3137 87
VMA CriteriaM
inim
um V
MA
(%)
10
Nominal Maximum Particle Size
20
30
40
50
2"1½"1"¾"½"4 3/8"840
Deficient in either
asphalt or air voids
CIVL 3137 88
13
14
15
16
17
18
3.5 4.0 4.5 5.0 5.5 6.0 6.5
Asphalt Content (%)
VM
A (%
)
Marshall Mix Design
TDOT requiresthe AC to be lessthan that whichminimizes VMA
CIVL 3137 89
Ways to Increase VMA
1. Reduce the dust content2. Open the aggregate gradation3. Gap-grade the aggregate blend4. Increase manufactured sand5. Reduce flat-and-elongated particles