Ctia Cdma Test Plan Rev 4.0

Test Plan for CDMA Mobile Stations

Cellular Telecommunications & Internet Association Performance Evaluation Standard for CDMA Mobile Stations

April, 2004

Revision 4.0

CTIA Certification Program Test Plan

CTIA Certification Programs

Interested parties may obtain permission to reproduce a limited number of copies by contacting the CTIA Certification Department at:

CTIA Certification Department

1400 16th Street, NW, Suite 600

Washington, DC 20036

e-mail: [email protected]

Telephone: 1.202.785.0081

www.certification.wow-com.com

This test plan has been written by QUALCOMM Incorporated of San Diego, CA on behalf of the CTIA Certification Programs. All rights to this test plan are held solely by CTIA.

© 2004 Cellular Telecommunications & Internet Association (CTIA). All rights reserved. CTIA has

granted a license to CTIA Authorized Testing Laboratories to use this Test Plan for the sole purpose of testing wireless products for the CTIA Certification Program. Any reproduction or transmission of all or part of CTIA's Test Plan, in any form or by any means, electronic or mechanical, including photocopying,

recording, or any information storage and retrieval system, without the prior written permission of the Cellular Telecommunications & Internet Association is unauthorized and strictly prohibited. Test

laboratories that are not CTIA Authorized Testing Laboratories and wish to use CTIA Test Plans must receive written permission from CTIA prior to such use.

.

April 2004 Revision 4.0

mailto:[email protected]

http://www.certification.wow-com.com/


TABLE OF CONTENTS

SECTION 1 INTRODUCTION............................................................................................. 1 1.1 PURPOSE .................................................................................................................................................................................1 1.2 SCOPE .....................................................................................................................................................................................1 1.3 APPLICABLE DOCUMENTS .........................................................................................................................................................2 1.4 TEST OVERVIEW.......................................................................................................................................................................4 1.5 TEST PROCESS ........................................................................................................................................................................4 1.6 EUT - EQUIPMENT UNDER TEST (MOBILE STATION) ..................................................................................................................5 1.7 MOBILE STATION DOCUMENTATION ...........................................................................................................................................6 1.8 ACRONYMS ..............................................................................................................................................................................6 1.9 DEFINITIONS.............................................................................................................................................................................9 1.10 BAND CLASS DEFINITION ...................................................................................................................................................10 1.11 REVISION HISTORY............................................................................................................................................................11

SECTION 2 MINIMUM PERFORMANCE...................................................................... 13 2.1 PURPOSE ...............................................................................................................................................................................13 2.2 SCOPE ...................................................................................................................................................................................13 2.3 SPECIAL REQUIREMENTS ........................................................................................................................................................13 2.4 CDMAONE ..............................................................................................................................................................................14 2.5 CDMA2000 .............................................................................................................................................................................14 2.6 CDMA2000 1XEVDO...............................................................................................................................................................15 2.7 POSITION LOCATION ...............................................................................................................................................................15

SECTION 3 SIGNALING CONFORMANCE .................................................................. 17 3.1 PURPOSE ...............................................................................................................................................................................17 3.2 SCOPE ...................................................................................................................................................................................17 3.3 CDMAONE®............................................................................................................................................................................17 3.4 CDMA2000 .............................................................................................................................................................................17 3.5 CDMA2000 1XEVDO...............................................................................................................................................................18 3.6 POSITION LOCATION ...............................................................................................................................................................18

SECTION 4 HANDSET STABILITY & PERFORMANCE............................................ 19 4.1 PURPOSE ...............................................................................................................................................................................19 4.2 SCOPE ...................................................................................................................................................................................19 4.3 CDMAONE ..............................................................................................................................................................................19 4.4 CDMA2000 .............................................................................................................................................................................19

APPENDIX A – CDMAONE TEST MATRICES ................................................................... 21 APPENDIX A.1 – CDMAONE MINIMUM PERFORMANCE TESTS ..............................................................................................................21 APPENDIX A.2 – CDMAONE SIGNALING CONFORMANCE TESTS ...........................................................................................................25 APPENDIX A.3.A – CDMAONE CDG 35 HANDSET STABILITY AND PERFORMANCE TESTS .....................................................................30

April 2004 ii Revision 4.0


APPENDIX A.3.B – CDMAONE CDG 64 HANDSET STABILITY AND PERFORMANCE TESTS .....................................................................31 APPENDIX B – CDMA2000 TEST MATRICES.................................................................... 33

APPENDIX B.1.A – CDMA2000 MINIMUM PERFORMANCE TESTS..........................................................................................................33 APPENDIX B.1.B – CDMA2000 1X-EVDO MINIMUM PERFORMANCE TESTS..........................................................................................36 APPENDIX B.1.C – CDMA2000 POSITION LOCATION MINIMUM PERFORMANCE TESTS ..........................................................................38 APPENDIX B.2.A – CDMA2000 SIGNALING CONFORMANCE TESTS.......................................................................................................39 APPENDIX B.2.B – CDMA2000 WIRELESS IP SIGNALING CONFORMANCE TESTS..................................................................................45 APPENDIX B.2.C – CDMA2000 1X-EVDO SIGNALING CONFORMANCE TESTS ......................................................................................47 APPENDIX B.2.D – CDMA2000 1X-EVDO WIRELESS IP SIGNALING CONFORMANCE TESTS .................................................................52 APPENDIX B.2.E – CDMA2000 POSITION LOCATION SIGNALING CONFORMANCE TESTS .......................................................................54 APPENDIX B.3.A – CDMA2000 CDG35 HANDSET STABILITY AND PERFORMANCE TESTS......................................................................55 APPENDIX B.3.B – CDMA2000 CDG64 HANDSET STABILITY AND PERFORMANCE TESTS......................................................................56

APPENDIX C – SAFE-FOR-NETWORK TEST REPORT FORMAT................................ 59

April 2004 iii Revision 4.0


Section 1 Introduction

1.1 Purpose

The purpose of this Test Plan is to define the CTIA Certification Program test requirements for evaluating CDMA Cellular/PCS Mobile Stations in a laboratory environment. This purpose is accomplished via performing the maximum set, supported by commercially available test equipment, of the compliance tests specified in TIA/EIA-98-E, the maximum possible set of signaling conformance tests specified in TIA/EIA-898, TIA-916, TIA-918, TIA-919, TIA-866, selected tests from CDG Reference 35 and CDG Reference 64, and certain criteria extracted from industry experience. These tests are performed against automated commercial test equipment in a laboratory environment. The purpose of these tests is to seek the absolute highest possible level of test coverage under automated, repeatable and fully controllable test conditions. To the maximum extent practical, testing requirements are based upon industry standards referenced in the pertinent sections of this document.

This Test Plan is part of a CTIA Certification Program as described in a separate document entitled CTIA Certification Program Management Document. This document contains criteria, in addition to laboratory conformance tests, that must be met for CTIA Certification.

1.2 Scope

This lab test plan is based on minimum performance tests specified in TIA/EIA-98-E, signaling conformance test cases extracted from TIA/EIA-898, TIA-916, TIA-866, CDG reference 35, performance-based test cases extracted from CDG Reference 64, and on non-standards based industry tests. The specific test set up, test procedures and test parameters are therefore referred back to industry standard specifications, where applicable. Appendices A & B provides the mapping between this Lab Test Plan and for cdmaOne® and for cdma2000® minimum performance and signaling conformance testing.

This Test Plan does not provide specific test equipment configurations or detailed test procedures by which to execute Certification testing. Such documentation and procedures must be presented by the CTIA Authorized Testing Laboratory (CATL) as part of the CATL authorization process and subsequently maintained and employed by the CATL to remain authorized to conduct Certification testing.

This Test Plan does not include the test requirements or test methodology for other Mobile Station standards or technologies (e.g., AMPS, GSM, TDMA). Aspects of multiple CTIA Test Plans are merged in those cases where a product supports a blend of multiple technologies.

April 2004 1 Revision 4.0


1.3 Applicable Documents

The following documents and published addendums are applicable to this Test Plan:

Recommended Minimum Performance Standards for cdma2000®1 Spread Spectrum Mobile Stations, TIA/EIA-98-E, February 2003, Telecommunications Industry Association

Optional System Performance Tests, Revision 3.0, CDG Reference 35, April 2003, CDMA Development Group

Signaling Conformance Tests for cdma2000® Spread Spectrum Systems, TIA/EIA-898 December 2001, Telecommunications Industry Association

Mobile Station-Base Station Compatibility Standard for Dual-Mode Wideband Spread Spectrum Cellular System. TIA/EIA/IS-95-A, May 1995, Telecommunications Industry Association.

Introduction to cdma2000® Standards for Spread Spectrum Systems - Addendum 2, TIA/EIA/IS-2000.1-2, August 2001, Telecommunications Industry Association.

Physical Layer Standard for cdma2000® Spread Spectrum Systems - Addendum 2, TIA/EIA/IS-2000.2-2, August 2001, Telecommunications Industry Association

Medium Access Control (MAC) Standard for cdma2000® Spread Spectrum Systems - Addendum 2, TIA/EIA/IS-2000.3-2, August 2001, Telecommunications Industry Association

Signaling Link Access Control (LAC) Standard for cdma2000 Spread Spectrum Systems - Addendum 2, TIA/EIA/IS-2000.4-2, August 2001, Telecommunications Industry Association

Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread Spectrum Systems - Addendum 2, TIA/EIA/IS-2000.5-2, August 2001, Telecommunications Industry Association

Analog Signaling Standard for cdma2000 Spread Spectrum Systems - Addendum 2, TIA/EIA/IS-2000.6-2, August 2001, Telecommunications Industry Association

Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal, TIA-866, February 2002, Telecommunications Industry Association

Signaling Conformance Standard for cdma2000 High Rate Packet Data Air Interface, TIA-919, May 2002, Telecommunications Industry Association

cdma2000 High Rate Packet Data Air Interface Specification, TIA/EIA/IS-856-1, January 2002, Telecommunications Industry Association

1 cdma2000® is a registered trademark of the Telecommunications Industry Association (TIA-USA)



Recommended Minimum Performance Specification for TIA/EIA/IS-801-1 Spread Spectrum Mobile Stations, TIA-916, April 2002, Telecommunications Industry Association

Position Determination Service Standard for Dual Mode Spread Spectrum Systems - Addendum 1, TIA/EIA/IS-801-1, March 2001, Telecommunications Industry Association

CTIA Certification Program Management Document, Revision 3.1, February 2004, CTIA.

Enhanced Variable Rate Codec, Speech Service Option 3 for Wideband Spread Spectrum Digital Systems, TIA/EIA/IS-127-1

Short Message Services for Wideband Spread Spectrum Cellular Systems, TIA/EIA/IS-637-A

Data Service Options for Wideband Spread Spectrum Systems, TIA/EIA/IS-707-A

High Rate Speech Service Option 17 for Wideband Spread Spectrum Communications Systems Addendum 1, TIA/EIA/IS-733-1

cdma2000 High Rate Packet Data Air Interface Specification, TIA/EIA/IS-856-1.

Administration of Parameter Value Assignment for TIA/EIA Spread Spectrum Standards, TSB-58

CDG Stage 3 Testing for cdma2000, CDG Reference 64.

Mobile Station Diagnostic Monitor Minimum Requirements, CDG Reference 45.

Signaling Conformance Specification for cdma2000 Wireless IP Networks, TIA-918

Additional Standards may be referenced within the above standards.

The above specifications may be found at one of the following:

Global Engineering Documents 15 Inverness Way East Englewood CO 80112 USA Phone: 1-800- 854-7179 Phone: 1-303-792-2181 Fax: 1-303- 754-4030 Web: http://global.ihs.com/

CDG reference documents are available via the CDG web site at http://www.cdg.org. Documents are also available to non-members for a nominal fee. Contact the CDG at 1-714-545-5211 to order Reference Documents.

3GPP documents can be downloaded from the web site http://www.3gpp.org.

3GPP2 documents can be downloaded from the web site http://www.3gpp2.org.


http://global.ihs.com/

http://www.cdg.prg/

http://www.3gpp.org/

http://www.3gpp.org/


CTIA documents can be obtained by contacting [email protected]

1.4 Test Overview

This Test Plan presents general requirements for the test environment (equipment configurations, procedures, uncertainty analyses, results reporting), minimum performance testing, cabled interoperability testing, and system performance testing of Mobile Stations incorporating CDMA technologies.

All testing shall be conducted as described in the CTIA Certification Program Management Document (see Laboratory Test Procedures section).

Tests are to be conducted only if the corresponding features are supported by the mobile station. The manufacturer shall provide to the CATL a list of features supported by the mobile station.

The test matrices in Appendix A – cdmaOne Test Matrices and Appendix B – cdma2000 Test Matrices provide a roadmap of when the tests are required. The first column (Test Required) indicates tests required today. The second column (Required in Next Revision) indicates additional tests that will be required in the next revision of this test plan. The third column (Required in Future Revision) indicates additional tests that are planned to be required in a future revision of this Test Plan. If there are tests marked in the “Required in Next Revision” column, the next revision of this Test Plan will be published 90 days after the current revision.

Test failures shall be handled as described in the CTIA Certification Program Management Document (see Test Failures section).

The test report shall include the minimum information as described in the CTIA Certification Program Management Document (see Laboratory Reporting section).

1.4.1. Special Results Reporting

Traffic, Paging, and Pilot Channel gain settings shall be verified prior to executing any tests using a code domain analyzer. Measured numbers shall be stated in the test report next to the base station settings.

1.5 Test Process

All testing shall be conducted at a CTIA Authorized Testing Laboratory (CATL). A current list of CATLs can be found at www.certification.wow-com.com. Products shall be submitted for testing in accordance with the instructions detailed in the CTIA Certification Program Management Document. Testing to this test plan may follow either a one-part test process or a two-part test process as described below.


mailto:[email protected]

http://www.certification.wow-com.com/


1.5.1. One-Part Test Process

In the one-part test process, all tests identified as required in this Test Plan must be completed and the results reported as described in the CTIA Certification Program Management Document (see Laboratory Reporting section). The CATL will upload the test report to CTIA’s online certification database as described in the CTIA Certification Program Management Document.

1.5.2. Two-Part Test Process

In the two-part test process, Safe-For-Network tests are conducted first. These tests are identified by “SFN” in the test matrices in this Test Plan. Safe For Network tests shall be conducted on the same hardware version as the units to be used on the network and should be the same physical devices. The results are reported in the format as shown in Appendix C – Safe-For-Network Test Report Format and uploaded to CTIA’s online certification database by the CATL. At a later time, all tests identified as required in this Test Plan are conducted and those results uploaded to CTIA’s online certification database by the CATL.

The purpose of this two-part process is to allow the product manufacturer to obtain access to an operator’s network at the earliest opportunity possible, by demonstrating that the mobile station will not adversely impact network performance. The operator will review the Safe-For-Network test results and, if the results meet the operator’s requirements, provide access to the network to support development testing. Once development testing is complete, and the manufacturer is ready to complete the certification testing process, the entire set of required tests in this Test Plan may be conducted.

1.5.2.1. Channel Requirements

The CATL shall contact the operator in the product’s target market to determine the channels used during Safe For Network certification testing. Unless otherwise specified by the operator, the Mobile Station or Access Terminal shall be tested using channels 384, 777, and 1013 for the 800 MHz band, and 25, 600, and 1175 for PCS operation. Products not capable of supporting the specified “test” channels shall be identified prior to the start of testing. Alternative test channels may be used but they shall fall as closely as possible to the default channels defined.

1.6 EUT - Equipment Under Test (Mobile Station)

In accordance with the CTIA Certification Program Management Document, units for test are to be supplied with all required peripherals and accessories. In addition, any auxiliary equipment which is available as part of the product, either for installation or as an option, should be supplied.



1.7 Mobile Station Documentation

All documentation associated with the installation and operation of the mobile station shall be supplied in accordance with the CTIA Certification Program Management Document (see Certification Testing Checklist). This should include:

• User guides or manuals • Programming instructions • Installation guides or manuals • Service manuals, including manual control of EUT from Test Interface Unit

and/or keypad • Identification of the IF frequencies used in the receiver. • Diagram of the Test Interface Unit, giving details of the pin connections. • List of preprogrammed SIDs in the CATL-specified Preferred Roaming List

(PRL)

In addition to the documentation, a contact person and telephone number for the manufacturer shall be supplied to provide technical or operational assistance if necessary.

1.8 Acronyms AC Authentication Center ACCOLC Access Overload Class AMPS Advanced Mobile Phone Service (AMPS) AWGN Additive White Gaussian Noise BPS Bits per Second BS Base Station CAN Calling Party Name CATL CTIA Authorized Testing Laboratory CC Channel Configuration CCI Base-station Configuration Change Indicator (sent on the QPCH) CCITT The International Telegraph and Telephone Consultative CommitteeCDG CDMA Development Group CDMA Code Division Multiple Access CDPD Cellular Digital Packet Data CFNA Call Forwarding No Answer CFSReqM Candidate Frequency Search Request Message CMT Cellular Messaging Teleservice CNAP Calling Name Presentation CNI Calling Number Identification CPN Calling Party Number CPT Cellular Paging Teleservice CRC Cyclic Redundancy Code CTIA Cellular Telecommunications & Internet Association D/A Digital to Analog DCC Digital Color Code



DCE Data Circuit Terminating Equipment DTE Data Terminal Equipment DTMF Dual Tone Multiple Frequency DTX Discontinuous Transmission ECAM Extended Channel Assignment Message EHDM Extended Handoff Direction Message EIA Electronic Industries Association ENLUM Extended Neighbor List Update Message ESCAM Extended Supplemental Channel Assignment Message ESN Electronic Serial Number ESPM Extended System Parameter Message EUT Equipment Under Test FER Frame Error Rate F-FCH Forward Fundamental Channel FFPC Fast Forward Power Control FO Frame Offset FPC Forward Power Control F-PICH Forward Pilot Channel F-SCH Forward Supplemental Channel FTP File Transfer Protocol GHDM General Handoff Direction Message GNLM General Neighbor List Message HO Handoff IEEE Institute of Electrical and Electronic Engineers IMSI_M MIN based IMSI IMSI_T True IMSI IMSI_T_11_12 Mobile Country Code of IMSI_T IMSI_T_S Supplement of the MIN-based IMSI IS Interim Specification ITU International Telecommunication Union IWF Inter-Working Function LAC Link Access Control MAC Medium Access Control MC Message Center MCC Mobile Country Code MDR Medium Data Rate MIN/MSIN Mobile Station Identification Number MO Multiplex Option MS Mobile Station MT Mobile Terminal MWI Message Waiting Indicator NAK Negative Acknowledgement. NAM Number Assignment Module NDSS Network Directed System Selection



NID Network Identifier NNSCR Non-Negotiable Service Configuration Record OA&M Operation, Administration, and Maintenance OCNS Orthogonal Channel Noise Simulator OLPC Outer Loop Power Control ORM Origination Message OUNS Other User Noise Simulator P_REV_IN_USE Protocol revision level in use PCF Packet Control Function PD Protocol Discriminator PDU Protocol Data Unit PI Paging Indicator PIN Personal Identification Number PLC Private Long Code PM Privacy Mode PN Pseudo-random Noise POTS Plain Old Telephone Service PPP Point-To-Point Protocol PRL Preferred Roaming List PRM Page Response Message PS Pilot Strength PSTN Public Switching Telephone Network QOF Quasi-Orthogonal Function QPCH Quick Paging Channel R-ACH Reverse Access Channel RC Radio Configuration RC Radio configuration RF Radio Frequency R-FCH Reverse Fundamental Channel RLP Radio Link Protocol RND Redirecting Name Delivery RPC Reverse Power Control R-PCSCH Reverse Power Control Subchannel R-PICH Reverse Pilot Channel R-SCH Reverse Supplemental Channel SCM Station Class Mark SCR Service Configuration Record SCRM Supplemental Channel Request Message SDB Short Data Burst SDU Service Data Unit SFN Safe For Network SID System Identification Number SME Signaling Message Encryption SMS Short Message Service



SO Service Option SR Service Redirection SRQM Service Request Message SSD Shared Secret Data SSPR System Selection for Preferred Roaming TCH Traffic Channel TCP Transmission Control Protocol TDMA Time Division Multiple Access TDSO Test Data Service Option TE Terminal Equipment TE2L Terminal Equipment at land connection point TE2M Terminal Equipment at mobile connection point TIA Telecommunications Industry Association TMSI Temporary Mobile Station Identity TRAC Terminal Rapid Acceptance for CDMA TSB Technical Service Bulletin UHDM Universal Handoff Direction Message UI User Interface V.42 ITU-T recommended error correction protocol VCAS Valid Configuration Attribute Selection VMN Voice Mail Notification VMNI Voice Mail Notification Indicator WC Walsh Code WLL Wireless Local Loop

1.9 Definitions

Term Definition

Access Terminal A device providing data connectivity to a user. An access terminal may be connected to a computing device such as a laptop personal computer or it may be a self-contained data device such as a personal digital assistant. An access terminal is equivalent to a mobile station in an IS-2000 system.

Mobile Station An entity in the public cellular radio telecommunications service intended to be used while in motion or during halts at unspecified points. Mobile stations include portable units (e.g., hand-held personal units) and units installed in vehicles.



1.10 Band Class Definition The following is a list of the band classes defined in IS-2000:

Band Class 0 (800 MHz band) Band Class 1 (1900 MHz band) Band Class 2 (TACS band) Band Class 3 (JTACS band) Band Class 4 (Korean PCS band) Band Class 5 (NMT-450 band) Band Class 6 (IMT-2000 band) Band Class 7 (700 MHz cellular band) Band Class 8 (1800 MHz band) Band Class 9 (900 MHz band) Band Class 10 (Secondary 800 MHz band) Band Class 11 (400 MHz European PAMR band) Band Class 12 (800 MHz PAMR band)



1.11 Revision History

Test Plan for CDMA Mobile Stations

Date Revision Purpose/Change January 1998 Draft 1.0 Issued For Comments February 1998 Draft 1.1 Issued For Comments June 1998 Release 1.2 Changed to reflect IS-98-B Included CDMA Environmental Tests Calibration Procedure Added Added Analog Call Setup Modified CDMA Results Tables Added Thermal Shock January 1999 Draft 1.3 (not

released) General Reformat Simplified Table/Figure Referencing Extensive Review and Update of Existing Procedures

November 1999 Release 2.0 (not released)

CDMA testing now reflects use of TAS hardware and software Added support for 8924C idle and soft handoff tests All tests now reflect TIA/EIA-98-B General revision of procedures

February 2000 Release 2.1 CDMA Authentication added Acoustics reflect new B&K 6713 Editorial changes made

November 2001 Release 3.0 Certification program restructured Replaces previously titled “Test Plan for 800 MHz AMPS & Cellular/PCS CDMA Wireless Subscriber Stations”

October 2002 Release 3.1 Updated applicable documents to latest specifications Added acronyms table Updated 1x and position location tests to reflect latest specifications Added TIA/EIA-898 references to signaling conformance tests Identified signaling conformance tests as informational-only Clarified system performance tests and added CDG35 test matrices Editorial changes

November 2003 Release 3.2 Updated reference to document Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations to Version TIA/EIA-98-E Deleted reference to TIA/EIA-98-E, Ballot Version Updated PMD reference to Rev. 3.0 Corrected TIA-919 title Revised signaling conformance test requirements Provided roadmap for future test requirements

April 2004

Release 4.0

Expanded Test Coverage, including 1x-EvDO & Position Location Removed test cases; updated test matrices; added hybrid test Added Test Process section and safe-for-network test report format Identified safe for network test cases in test matrices Revised test coverage to reflect CATL input on test capability Clarified radiated test coverage requirements Allowed testing per spirit of CDG References 35 & 64 Updated PMD reference to Rev. 3.1



This page intentionally left blank.



Section 2 Minimum Performance

Wireless Mobile Stations and Access Terminals regardless of specific CDMA technology shall demonstrate minimum parametric performance in order to be considered for CTIA Certification. CTIA Authorized Testing Laboratories shall conduct minimum parametric performance testing per the relevant specifications outlined below.

2.1 Purpose

The purpose of Minimum Performance testing is to perform the maximum set, supported by commercially available test equipment, of the compliance tests specified in TIA/EIA-98-E. These tests are performed against automated commercial test equipment. The purpose of these tests is to seek the absolute highest possible level of test coverage under automated, repeatable and fully controllable test conditions.

2.2 Scope

These tests are based on minimum performance tests specified in TIA/EIA-98-E. The specific test set up, test procedures and test parameters are referred back to these specifications unless otherwise stated herein.

2.3 Special Requirements

The following are clarifications to the requirements defined in TIA/EIA-98-E. In the event of conflict, this document shall supercede.

2.3.1. Channel Coverage

Some tests require that the phone be tested across the entire band. The channels used during CTIA Certification testing are 384, 777, and 1013 for the 800 MHz band, and 25, 600, and 1175 for PCS operation. Products not capable of supporting these default “test” channels shall be identified prior to the start of testing. Alternative test channels may be used but they shall fall as closely as possible to the default channels defined.

2.3.2. Single Tone

Single tone test section 3.5.2 shall be performed in both RC1 and RC2 modes. For RC2 mode service option 9 shall be selected and the traffic channel gain setting shall use the table given for Receiver Sensitivity tests (-12.3 dB).

2.3.3. Hard Hand Off Timing

Transmit power after hard handoff test (section 4.2.1) shall be performed with a BS or BS emulator that is capable of simultaneously transmitting in two different



channels and internally/externally synchronized. The second BS shall turn ON the traffic channel prior to sending the universal handoff direction message and the output power measurement in this traffic channel should closely be monitored for any transients during T2 (the time elapsed from the action time to the instant the Mobile Station transmitter is enabled on the new CDMA frequency assignment).

2.3.4. Maximum RF Output Power

The Maximum RF Output Power test (section 4.4.5) shall be performed as a conducted test. 0dB shall be used as the “antenna gain recommended by the mobile station manufacturer” in section 4.4.5.3.

2.3.5. Hybrid Tests

The TIA-916 "Recommended Minimum Performance Specification for TIA/EIA/IS-801-1 Spread Spectrum Mobile Stations" Section 4.2.2 shall be performed with the following exceptions. The PDE shall be used to determine horizontal error. Satellite vehicles PRN 17 and PRN 21 shall be set to a signal level of -144dBm. All other satellite vehicles shall be set to OFF.

2.4 cdmaOne

Mobile Stations designed to operate in conformance to TIA/EIA/IS-95-A “Mobile Station-Base Station Compatibility Standard for Dual-Mode Wideband Spread Spectrum Cellular System” shall be tested per TIA/EIA-98-E “Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations.” As a minimum, such Mobile Stations shall demonstrate compliance with those sections of TIA/EIA-98-E marked with an “X” in Appendix A.1 – cdmaOne Minimum Performance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.

2.5 cdma2000

Mobile Stations designed to operate in conformance to IS-2000 “cdma2000 Standards for Spread Spectrum Systems” shall demonstrate compliance to TIA/EIA-98-E “Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations.” As a minimum, such Mobile Stations shall demonstrate compliance with those sections of TIA/EIA-98-E marked with an “X” in Appendix B.1.A – cdma2000 Minimum Performance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.



2.6 cdma2000 1xEvDO

Access Terminals designed to operate in conformance to TIA/EIA/IS-856-1 “cdma2000 High Rate Packet Data Air Interface Specification” shall be tested per TIA-866 “Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal”. As a minimum, such Mobile Stations shall demonstrate compliance with those sections of TIA-866 marked with an “X” in Appendix B.1.B – cdma2000 1x-EvDO Minimum Performance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.

2.7 Position Location

Mobile Stations and Access Terminals designed to operate in conformance to TIA/EIA/IS-801-1 “Position Determination Service Standard for Dual Mode Spread Spectrum Systems - Addendum 1” shall be tested per TIA-916, “Recommended Minimum Performance Specification for TIA/EIA/IS-801-1 Spread Spectrum Mobile Stations”. As a minimum, such Mobile Stations shall demonstrate compliance with those sections of TIA-916 marked with an “X” in Appendix B.1.C – cdma2000 Position Location Minimum Performance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.



This page intentionally left blank.



Section 3 Signaling Conformance

Wireless Mobile Stations and Access Terminals regardless of specific CDMA technology shall demonstrate minimum signaling conformance in order to be considered for CTIA Certification. CTIA Authorized Testing Laboratories shall conduct minimum signaling conformance testing on commercially available test equipment per the relevant test specifications outlined below.

3.1 Purpose

The purpose of Signaling Conformance testing is to perform the maximum set, supported by commercially available test equipment, of the signaling conformance tests specified in TIA/EIA-898, TIA-919, and TIA-918. These tests are performed against automated commercial test equipment. The purpose of these tests is to seek the absolute highest possible level of test coverage under automated, repeatable and fully controllable test conditions.

3.2 Scope

These tests are based on signaling conformance test cases extracted from TIA/EIA-898, TIA-919, and TIA-918. The specific test set up, test procedures and test parameters are referred back to these specifications unless otherwise stated herein.

3.3 cdmaOne®

Mobile Stations designed to operate in conformance to TIA/EIA/IS-95-A “Mobile Station-Base Station Compatibility Standard for Dual-Mode Wideband Spread Spectrum Cellular System” shall be tested per TIA/EIA-898 “Signaling Conformance Tests for cdma2000 Spread Spectrum Systems. As a minimum, such Mobile Stations must demonstrate compliance with those sections TIA/EIA-898 marked with an “X” in Appendix A.2 – cdmaOne Signaling Conformance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.

3.4 cdma2000

Mobile Stations designed to operate in conformance to IS-2000 “cdma2000 Standards for Spread Spectrum Systems” shall be tested per TIA/EIA-898 “Signaling Conformance Tests for cdma2000 Spread Spectrum Systems. As a minimum, such Mobile Stations shall demonstrate compliance with those sections of TIA/EIA-898 marked with an “X” in



Appendix B.2.A – cdma2000 Signaling Conformance Tests and Appendix B.2.B – cdma2000 Wireless IP Signaling Conformance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.

3.5 cdma2000 1xEvDO

Access Terminals designed to operate in conformance to TIA/EIA/IS-856-1 “cdma2000 High Rate Packet Data Air Interface Specification” shall be tested per TIA-919 “Signaling Conformance Standard for cdma2000 High Rate Packet Data Air Interface.” As a minimum, such Mobile Stations must demonstrate compliance with those sections of TIA-919 marked with an “X” in Appendix B.2.C – cdma2000 1x-EvDO Signaling Conformance Tests and

Appendix B.2.D – cdma2000 1x-EvDO Wireless IP Signaling Conformance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.

3.6 Position Location

Mobile Stations and Access Terminals designed to operate in conformance to TIA/EIA/IS-801-1 “Position Determination Service Standard for Dual Mode Spread Spectrum Systems - Addendum 1” must demonstrate compliance with those sections of TIA-916 “Recommended Minimum Performance Specification for TIA/EIA/IS-801-1 Spread Spectrum Mobile Stations” marked with an “X” in Appendix B.2.E – cdma2000 Position Location Signaling Conformance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.



Section 4 Handset Stability & Performance

Wireless Mobile Stations and Access Terminals regardless of specific CDMA technology shall demonstrate stability and performance in order to be considered for CTIA Certification. CTIA Authorized Testing Laboratories shall conduct stability and performance testing per the relevant test specifications outlined below. When testing per the specification is not commercially practical, testing shall be conducted on commercial test equipment to the spirit of the specification.

4.1 Purpose

The purpose of Handset Stability & Performance testing is to perform the maximum set, supported by commercially available test equipment, of selected tests from CDG Reference 35, CDG Reference 64, and against certain criteria extracted from industry experience. These tests are performed against automated commercial test equipment. The purpose of these tests is to verify overall terminal robustness and performance.

4.2 Scope

Handset Stability & Performance Testing is based on CDG Reference 35, CDG Reference 64, and on non standards based industry tests. The sections below define the test cases not defined in the standards. When a test procedure is defined in an existing standard the tables in the relevant appendices point to the corresponding section number in the standard.

4.3 cdmaOne

Mobile Stations designed to operate in conformance to TIA/EIA/IS-95-A “Mobile Station-Base Station Compatibility Standard for Dual-Mode Wideband Spread Spectrum Cellular System” shall be tested per CDG Reference 35 “Optional System Performance Tests, Revision 3.0” as marked with an “X” in Appendix A.3.A – cdmaOne CDG 35 Handset Stability and Performance Tests and CDG Reference 64 “CDG Stage 3 Testing for cdma2000” as marked with an “X” in Appendix A.3.B – cdmaOne CDG 64 Handset Stability and Performance Tests in order to be considered for CTIA Certification. Test cases marked with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.

4.4 cdma2000

Mobile Stations designed to operate in conformance to IS-2000 “cdma2000 Standards for Spread Spectrum Systems” shall be tested per CDG Reference 35 “Optional System Performance Tests, Revision 3.0” as marked with an “X” in Appendix B.3.A – cdma2000

CDG35 Handset Stability and Performance Tests, CDG Reference 64 “CDG Stage 3 Testing for cdma2000” as marked with an “X” in Appendix B.3.B – cdma2000 CDG64 Handset Stability and Performance Tests, and as further defined in this section. Test cases



marked in the Appendices with “NA” are deemed not applicable and test cases marked with “–“ are deemed not to be required.



Appendix A – cdmaOne Test Matrices

Appendix A.1 – cdmaOne Minimum Performance Tests TIA/EIA-

98-E Section Description

Test Required

Required in Next

Revision

Required in Future

Revision 1.3 Fundamental Channel Test Mode 1 (F/R RC1) X Fundamental Channel Test Mode 2 (F/R RC2) X Fundamental Channel Test Mode 3 (F/R RC3) NA2 Supplemental Channel Test Mode 3 (Fwd RC3) NA Fundamental Channel Test Mode 4 (F-RC4 & R-RC3) NA Supplemental Channel Test Mode 4 (Fwd RC4) NA Fundamental Channel Test Mode 5 (F-RC5 & R-RC4) NA Supplemental Channel Test Mode 5 (Fwd RC5) NA

3 CDMA RECEIVER MINIMUM STANDARDS

3.1 Frequency Coverage Requirements 3.1.1 Band Class 0 (800 MHz band) X 3.1.2 Band Class 1 (1900 MHz band) X 3.1.3 Band Class 2 (TACS band) NA 3.1.4 Band Class 3 (JTACS band) NA 3.1.5 Band Class 4 (Korean PCS band) NA 3.1.6 Band Class 5 (NMT-450 band) NA 3.1.7 Band Class 6 (IMT-2000 band) NA 3.1.8 Band Class 7 (700 MHz cellular band) NA 3.1.9 Band Class 8 (1800 MHz band) NA

3.1.10 Band Class 9 (900 MHz band) NA

3.2 Acquisition Requirements

3.2.1 Idle Handoff Tests

3.2.1.1 Idle Handoff in non-Slotted Mode on the Paging Channel X

3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel X

3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control Channel NA

3.2.1.4 Idle Handoff to Another Frequency X

3.2.2 Soft Handoff Tests

3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft Handoff X

3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft Handoff X

3.2.2.3 Active Set Pilot Loss Detection in Soft Handoff X

3.2.3 Access and Access Probe Handoff Tests

3.2.3.1 Access Probe Handoff NA

2 “NA” means Not Applicable.



TIA/EIA-98-E

Section Description Test

Required

Required in Next

Revision

Required in Future

Revision 3.2.3.2 Access Handoff NA

3.2.4 Candidate Frequency Single Search NA

3.3 Forward Common Channel Demodulation Performance

3.3.1 Demodulation of non-Slotted Mode Paging Channel X

3.3.2 Demodulation of Slotted Mode Paging Channel X

3.3.3 Demodulation of Broadcast Control Channel in AWGN Channel NA

3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading Channel NA

3.3.5 Demodulation of Forward Common Control Channel NA

3.3.6 Demodulation of Common Assignment Channel and Reception of Common Power Control Channel NA

3.4 Forward Traffic Channel Demodulation Performance

3.4.1 Demodulation of Forward Traffic Channel in Additive White Gaussian Noise X

3.4.23 Demodulation of Forward Traffic Channel in Multipath Fading Channel X

3.4.3 Demodulation of Forward Traffic Channel During Soft Handoff X

3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power Control Sets During Soft Handoff X

3.4.5 Decision of Power Control Bit for Channels Belonging to the Same Power Control Set X

3.4.6 Demodulation of Power Control Subchannel During Soft Handoff X

3.4.7 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Closed Loop Power Control (FPC_MODE='000') NA

3.4.8 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Closed Loop Power Control (FPC_MODE='010') NA

3.4.9 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Outer Loop Power Control and Closed Loop Power Control (FPC_MODE='000', '001' and '010')

NA

3.4.10 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Closed Loop Power Control (FPC_MODE='000') and Transmit Diversity (OTD or STS)

NA


NA

3 Test 12 is not required



TIA/EIA-98-E


Required

Required in Next

Revision

Required in Future

Revision

3.4.12 Demodulation of Power Control Subchannel During Reverse Pilot Channel Gating NA

3.4.13 Demodulation of Power Control Subchannel During Reverse Fundamental Channel Gating NA

3.5 Receiver Performance

3.5.1 Receiver Sensitivity and Dynamic Range X

3.5.2 Single Tone Desensitization X

3.5.3 Intermodulation Spurious Response Attenuation X

3.5.4 Adjacent Channel Selectivity

3.5.5 Receiver Blocking Characteristics

3.6 Limitations on Emissions

3.6.1 (Rx) Conducted Spurious Emissions X; SFN4

3.6.25 (Rx) Radiated Spurious Emissions X

3.7 Supervision

3.7.1 Paging Channel X

3.7.2 Forward Traffic Channel X

4 CDMA TRANSMITTER MINIMUM STANDARDS

4.1 Frequency Accuracy X; SFN

4.2 Handoff

4.2.1 CDMA to CDMA Hard Handoff X; SFN

4.2.2 Transmit Power After Hard Handoff X; SFN

4.3 Modulation Requirements

4.3.1 Time Reference X; SFN

4.3.2 Reverse Pilot Channel to Code Channel Time Tolerance NA

4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance NA

4.3.4 Waveform Quality and Frequency Accuracy X; SFN

4.3.5 Code Domain Power X; SFN

4.4 RF Output Power Requirements

4.4.1 Range of Open Loop Output Power X; SFN

4.4.2 Time Response of Open Loop Power Control X; SFN

4.4.3 Access Probe Output Power X; SFN

4.4.4 Range of Closed Loop Power Control X; SFN

4.4.56 Maximum RF Output Power X; SFN

4.4.6 Minimum Controlled Output Power X; SFN

4 “SFN” indicates a Safe-For-Network Test

5 This test is covered during FCC Compliance testing and therefore is not required to be performed by the CATL

6 When testing RC 3 + SCH, if the procedure outlined in TIA-98-E gives incorrect results, the CATL may use an alternate procedure for conducting this test



TIA/EIA-98-E


Required

Required in Next

Revision

Required in Future

Revision 4.4.7 Standby Output Power and Gated Output Power X; SFN

4.4.8 Power Up Function Output Power NA

4.4.9 Code Channel to Reverse Pilot Channel Output Power Accuracy NA

4.4.9.2.1 Code Channel Output Power for the Enhanced Access Channel Header, Enhanced Access Channel Data, and Reverse Common Control Channel Data

NA

4.4.9.2.2 Code Channel Output Power for the Reverse Traffic Channel NA

4.4.10 Reverse Pilot Channel Transmit Phase Discontinuity NA

4.4.11 Reverse Traffic Channel Output Power During Changes in Data Rate NA

4.5 Limitations on Emissions

4.5.1 (Tx) Conducted Spurious Emissions X; SFN

4.5.27 (Tx) Radiated Spurious Emissions SFN

4.5.3 Occupied Bandwidth

5 Environmental Requirements

5.1 Temperature and Power Supply Voltage X

5.2 High Humidity X

5.3 Vibration Stability X

5.4 Shock Stability X

7 This test is covered during FCC Compliance testing and therefore is not required to be performed by the CATL for certification testing. For Safe-for-Network testing only, test results may be provided to the CATL by the product manufacturer (in such cases, the test results must be marked as provided by the product manufacturer).



Appendix A.2 – cdmaOne Signaling Conformance Tests TIA/EIA-

898 Section

Description

Required for P_REV_IN_USE

<= 3

Required in Next

Revision

Required in Future

Revision

1 Miscellaneous Air Interface Tests 1.1 Pilot PN Offset X 1.2 Hashing CDMA Channels, Paging Channels, and Paging Slot X 1.3 Idle Ping Pong with Quick Paging Channel CCI NA 1.4 Quick Paging Indicator NA 1.5 Mobile Station Processing of the Access Parameters Message X 1.6 Mobile Station Processing of MIN_P_REV X 1.7 Mobile Station Response to Status Request Message X

1.8 Protocol Discriminator (PD) Test and Link Access Control (LAC) PDU Format Test on the Access Channel NA

1.9 Logging Tests X 1.10 SYNC Channel Support X 2 POTS Tests 2.1 Mobile Station Originated Call X; SFN

2.2 Mobile Station to Land Party Call, Radio Link Failure During Conversation - Reverse Link X

2.3 Mobile Station to Land Party, Radio Link Failure During Conversation - Forward Link X; SFN 2.4 Mobile Station Originated Call, Test Service Options X; SFN 2.5 Mobile Station to Land Party Call, Busy Tone X 2.6 Mobile Station to Land Party Call, No Traffic Channel Resources Available X 2.7 Mobile Station to Land Party Call, Reverse Link Failure During Call Setup X 2.8 Mobile Station to Land Party Call, Forward Link Failure During Call Setup X 2.9 Mobile Station Terminated Call X; SFN 2.10 Mobile Station terminated Call, Test Service Options X; SFN 2.11 Land Party to Mobile Station Call, Mobile Operating in Slotted Mode X; SFN 2.12 MSID, MCC, and IMSI X; SFN 2.13 TMSI Assignment 2.14 TMSI Expiration Time 2.15 Mobile Station to Land Party Call, DTMF X 2.16 Forward Traffic Channel DTMF Tone Signaling X 2.17 Enhanced DTMF Signaling X 2.18 Channel Assignment from CDMA to AMPS X 2.19 PACA Origination, User Terminates While Still In Queue NA 2.20 PACA Origination, Idle Handoff While in Queue NA 2.21 PACA Origination, Traffic Channel Becomes Available NA 2.22 PACA Origination, Features Interaction NA 2.23 PACA Origination, Permanent Invocation NA 2.24 PACA Origination, PACA Disabled for Mobile Station NA 2.25 True IMSI Support X 2.26 Initial Service Configuration and Negotiation NA 2.27 Base Station Requested Service Negotiation (Successful Scenarios) NA 2.28 Base Station Reject Scenarios during Service Negotiation NA 2.29 Mobile Station Reject Scenarios during Service Negotiation NA



TIA/EIA-898

Section

Description


<= 3

Required in Next

Revision

Required in Future

Revision

2.30 Service Negotiation Completion via General Handoff Direction Message and Universal Handoff Direction Message NA

2.31 SCR without NN-SCR and NN-SCR without SCR in General Handoff Direction Message and Universal Handoff Direction Message NA

2.32 Base Station Request Overrides the Mobile Station Request X 2.33 Service Negotiation Involving Partial SCR and/or Partial NN-SCR NA 2.34 Quasi-Orthogonal Functions (QOF) assignment NA 2.35 Release Order on Access Channel NA 3 Handoff Tests 3.1 Soft Handoff with Dynamic Threshold NA 3.2 Hard Handoff Between Frequencies in the Same Band Class X; SFN 3.3 Hard Handoff from CDMA to AMPS X 3.4 Soft Handoff in Fading X 3.5 Hard Handoff in Fading X 3.6 Hard Handoff Between Different Band Classes X; SFN 3.7 Hard Handoff with and without Return on Failure NA 3.8 Search Window Size and Offset Per Neighbor NA 3.9 Access Handoffs NA 3.10 Traffic Channel Preamble during Hard Handoff Between Frequencies in same band X 3.11 Hopping Pilot Beacon NA 3.12 Hard Handoff Between Frequencies with Different Radio Configurations NA 3.13 Handoff on Same Frequency with Different Radio Configurations NA 3.14 Hard Handoff while in the Waiting for Mobile Station Answer Substate X 3.15 Inter-Frequency Hard Handoff (CDMA to CDMA) X 3.16 Inter-Frequency Hard Handoff (CDMA to AMPS) X 3.17 Hard Handoff Between Frequencies with Different Protocol Revisions X 4 Power Control Tests 4.1 Forward Traffic Channel Power Control X 4.2 Mobile Station Response to Power Up Function (PUF) Message NA 4.3 Fast Forward Power Control (FFPC) NA 5 Registration Tests 5.1 Power-Up Registration X; SFN 5.2 Power-Down Registration X; SFN 5.3 Timer-Based Registration X; SFN 5.4 Distance-Based Registration X; SFN 5.5 Zone-Based Registration X; SFN 5.6 Parameter-Change Registration X; SFN 5.7 Registration Under Various Settings of MOB_TERM X; SFN 6 Authentication Tests 6.1 Shared Secret Data Initialized to Zero X 6.2 Shared Secret Data Update on the Paging/Access Channels X 6.3 Shared Secret Data Update on the Forward/Reverse Traffic Channels X 6.4 Mismatched A-Keys X 6.5 Activating Voice Privacy on Call Setup X 6.6 Activating Voice Privacy at the Mobile Station When a Call Is Active X



TIA/EIA-898

Section

Description


<= 3

Required in Next

Revision

Required in Future

Revision

6.7 Signaling Message Encryption on Forward Traffic Channel (Alert with Information Message) X

6.8 Signaling Message Encryption on Reverse Traffic Channel (Burst DTMF Message) X 6.9 Hard Handoffs between Base Stations with SME Active. X 6.10 Signaling Message Encryption Mobile Terminated SMS (Data Burst Message) X 6.11 Authentication Upon Originations X 6.12 Hard Handoff from CDMA to AMPS with SME Active X 7 Service Redirection 7.1 Global Service Redirection Tests X 7.2 Network Directed System Selection and Normal Service Redirection Tests X; SFN 7.3 Extended Global Service Redirection Tests X; SFN 8 Short Message Service (SMS) 8.1 Mobile Station Terminated SMS Tests X 8.2 Mobile Station Originated SMS Tests X 8.3 Broadcast SMS Tests X 9 Subscriber Calling Features Tests 9.1 Call Forwarding X 9.2 Three-Way Calling X 9.3 Land Party to Mobile Station Caller ID X 9.4 Call Waiting X 9.5 Message Waiting Indicator (MWI) X 9.6 Land Party to Mobile Station Calling Name Presentation X 9.7 Display Records X 9.8 TTY/TDD X 9.9 Answer Holding X 9.10 User Selective Call Forwarding X 10 Asynchronous Data and Fax Services 10.1 Send/Receive Fax X 10.2 Upload/Download Binary File X 10.3 Simultaneous Two-way File Transfer/Carrier Detect X 10.4 Compound AT Command, Initialization and Connection Delay X 10.5 Escaping to Command Mode X 10.6 Air Interface Data Compression X 10.7 RLP Operation in a Poor RF Environment X 10.8 RLP Abort and TCP Retransmit Test X 10.9 Internet Control Message Protocol (ICMP) Requests/Replies X 10.10 Reflection of AT Command Parameters X 11 Packet Data Services Tests 11.1 Terminal Session with Remote Host X 11.2 File Transfer X 11.3 IP Address Negotiation X 11.4 V-J Header Compression X 11.5 Asynchronous Control Character Mapping (ACCM) Negotiation X 11.6 PPP Field Compression X 11.7 Maximum Receive Unit (MRU) X



TIA/EIA-898

Section

Description


<= 3

Required in Next

Revision

Required in Future

Revision

11.8 Mobile Station Inactivity Timer X 11.9 IWF Inactivity Timer X 11.10 Radio Link Protocol (RLP) Operation in Rayleigh Fading X 11.11 RLP Abort and Upper Layer Retransmit X 11.12 RLP Encryption Negotiation X 11.13 Hardware Flow Control X 11.14 Re-connect after Hard Handoff X 11.15 Zone-Based Registration for Packet Data Mobile Stations X 12 Medium-Speed Packet Data 12.1 Forward File Transfer with Fundamental and Supplemental Code Channels NA 12.2 Forward File Transfer with Variable Supplemental Code Channels NA 12.3 MSPD Call Setup, No Negotiation NA 12.4 MSPD Call Setup, Negotiation to a Different MSPD Service Option NA 12.5 MSPD Call Setup, Negotiation to LSPD NA

12.6 MSPD Call Setup, Mobile Station Maximum Multiplex Option Less than Base Station Maximum Multiplex Option NA

12.7 MSPD Call Setup, Mobile station Maximum Multiplex Option Greater than Base Station Maximum Multiplex Option NA

12.8 Allocation/De-allocation of Supplemental Code Channels NA 12.9 No Transmission on Supplemental Code Channels NA 12.10 Soft Handoff with Supplemental Code Channels NA 12.11 Adding Supplemental Code Channels during Soft Handoff NA 12.12 Hard Handoff to an MSPD-Capable System NA 12.13 RLP Operation in Rayleigh Fading Environment NA 12.14 RLP Operation with Severely Degraded Channel NA 12.15 Bi-Directional File Transfers with Forward Supplemental Code Channels NA 12.16 Rм Interface Flow Control NA 12.17 Dormant Timer NA 12.18 Packet Zone ID NA 13 High Speed Packet Data 13.1 Forward File Transfer X 13.2 Reverse File Transfer X 13.3 Bi-directional File Transfer X 13.4 Basic Supplemental Channel Configuration Setting and Single Assignment X 13.5 Supplemental Channel Multiple Assignments NA 13.6 Turbo Coding on Supplemental Channel NA 13.7 Correct Walsh Cover NA 13.8 Supplemental Channel Discontinuous Transmission NA 13.9 Slotted Timer NA 13.10 Retry Order and Delay for Origination Message NA 13.11 Retry Order and Delay for Supplemental Channel Request Messages NA 13.12 Retry Order and Delay for Resource Request Messages NA 13.13 Base Station Initiated Active to Control Hold Mode Transitions NA 13.14 Mobile Station Initiated Active to Control Hold Mode Transitions NA 13.15 Base Station Initiated Control Hold to Active Mode Transitions NA



TIA/EIA-898

Section

Description


<= 3

Required in Next

Revision

Required in Future

Revision

13.16 Mobile Station Initiated Control Hold to Active Mode Transitions X 13.17 Base Station Ignores Mobile Station Requested Mode Transitions NA 13.18 Mobile station Multiplex Option different from Base Station Multiplex Option NA 13.19 Soft Handoff of Fundamental Channel and Supplemental Channels NA 13.20 Soft Handoff of Fundamental Channel only NA 13.21 Adding Supplemental Channels during Soft Handoff NA 13.22 Hard Handoff to HSPD-capable system NA 13.23 Hard Handoff from MSPD to HSPD NA 13.24 Hard Handoff from LSPD to HSPD NA 13.25 Hard Handoff to a different RC NA 13.26 Mobile Station Aborts R-SCH NA 13.27 RLP Operation in Rayleigh Fading Environment X 13.28 RLP Operation in Severely Degraded Channel X 13.29 Mobile Station Originated Short Data Burst NA 13.30 Mobile Station Terminated Short Data Burst NA 13.31 Mobile Assisted Burst Operation Parameters Message Test NA 13.32 Mobile Station and Base Station Operating in Different States NA

Data Services Tests Annex

14 Over-The-Air Services Required

for P_REV_IN_USE <= 3

Required in Next

Revision

Required in Future Revision

14.1 OTASP Service Request Processing X 14.2 OTAPA Service Request Processing for a Mobile Station in Mobile Station Idle State X 14.3 OTAPA Service Request Processing for a Mobile Station in Conversation Substate X 14.4 OTAPA Service Request Processing Interrupted by User Action X 15 System Selection for Preferred Roaming 15.1 OTASP Service Provisioning For System Selection and Preferred Roaming X 15.2 Non-Acquisition of a System on Negative Preferred Roaming List (PRL) X 15.3 Emergency Call On a System that is Negative on PRL or SID List X 15.4 OTASP For System Selection and Preferred Roaming - Oversize PRL X

15.5 OTAPA Service Provisioning for System Selection and Preferred Roaming for a Mobile Station in Mobile Station Idle State X

16 Message Driven Indicators 16.1 Enhanced Roaming Indicator X 17 Forward Compatibility Tests 17.1 Sync Channel 17.2 Paging Channel 17.3 Traffic Channel



Appendix A.3.A – cdmaOne CDG 35 Handset Stability and Performance Tests CDG Ref 35

Section System Performance Test Test

Required

Required in Next

Revision

Required in Future

Revision 1 Audio Quality Tests

1.1 Acoustic Dropouts in Hard Handoffs X

1.2 Acoustic Time Delay X

1.3 MOS (Mean Opinion Score) Predictive Test X

1.4 System Frequency Response Test X

1.5 Frame Error Rate

2 Mobile Station Talk time/Standby Time Tests

2.1 Mobile Station Talk Time X

2.2 Mobile Station Standby Time X

3 Reserved

4 Preferred Roaming List TESTS

4.1 Preferred Roaming List, Positive Entry Test X

4.2 Emergency Call On a System that is Negative on PRL X

4.3 System Acquisition X

4.4 OTASP For System Selection and Preferred Roaming - Oversize PRL

4.5 OTASP For System Selection and Preferred Roaming - PRL Upgrade with Shorter List



Appendix A.3.B – cdmaOne CDG 64 Handset Stability and Performance Tests CDG Ref 64

Section Test Case Name Required

Required in Next

Revision

Required in Future

Revision 4.1 System Acquisition and Registration

4.1.1 System Acquisition and Power-Up Registration

4.1.2 Power-Down Registration

4.1.3 System Acquisition from a Less Preferred System X

4.2 Successful Access

4.2.1 Mobile Originated Call Success Rate

4.2.2 Mobile Terminated Call Success Rate

4.3 In-Call Drive Tests

4.3.1 Long Call Maintenance with Handoffs and Fading

4.4 Idle State Drive Tests

4.4.1 Slotted Mode with Idle Handoffs and Registrations

4.4.2 Service Redirection

4.5 SMS

4.5.1 SMS Mobile Terminated in Idle State

4.5.2 SMS Mobile Originated from Idle State

4.5.3 SMS While in a Call

4.5.4 SMS Message Undeliverable

4.5.5 SMS Reply Option X

4.6 Subscriber Calling Features

4.6.1 Call Waiting

4.6.2 3-Way Calling

4.6.3 Caller ID

4.6.4 Call Forwarding

4.6.5 DTMF

4.6.6 TTY

4.6.7 Voice Privacy

4.6.8 CDMA Authentication

4.7 Voice Mail

4.7.1 Voice Mail Notification

4.7.2 Voice Mail Retrieval

4.7.3 No Answer with Release Order

4.8 OTA Provisioning and Maintenance

4.8.1 OTA Service Activation

4.8.2 OTA PRL Update



CDG Ref 64 Section Test Case Name Required

Required in Next

Revision

Required in Future

Revision 4.9 Mini-Browser

4.9.1 Mini-Browser Access in 3G (CDMA2000) NA

4.9.2 Mini-Browser Access in 2G (IS-95) NA

4.9.3 Mini-Browser Handoffs Between 2G and 3G NA

4.10 HSPD Tests

4.10.1 HSPD Basic Connection to the Internet NA

4.10.2 HSPD File Transfer Data Rate NA

4.10.3 HSPD Drive Test NA

4.10.4 HSPD PPP or IP Expiration NA

4.10.5 HSPD Mobile IP PDSN Hard Handoff NA

4.10.6 HSPD Mobile IP PDSN Dormant Idle Handoff NA

4.10.7 HSPD Ping while Dormant NA

4.10.8 HSPD Call Drop or Temporary Loss of Service NA

4.10.9 HSPD and Voice Calls NA

4.10.10 HSPD and SMS NA

4.11 Asynchronous Data and Fax

4.11.1 Initialization and Connection Delay

4.11.2 Mobile Origination and Speaker On Until Connect

4.11.3 Send/Receive Fax

4.11.4 Upload/Download Binary File

4.12 AMPS

4.12.1 Hard Handoff from CDMA to AMPS

4.12.2 Service Redirection from CDMA to AMPS



Appendix B – cdma2000 Test Matrices

Appendix B.1.A – cdma2000 Minimum Performance Tests TIA/EIA-98-E

Section Description Required for

P_REV_IN_USE = 6

Required in Next Revision

Required in Future

Revision 1.3 Fundamental Channel Test Mode 1 (F/R RC1) X Fundamental Channel Test Mode 2 (F/R RC2) X Fundamental Channel Test Mode 3 (F/R RC3) X Supplemental Channel Test Mode 3 (Fwd RC3) X Fundamental Channel Test Mode 4 (F-RC4 & R-RC3) X Supplemental Channel Test Mode 4 (Fwd RC4) X Fundamental Channel Test Mode 5 (F-RC5 & R-RC4) X Supplemental Channel Test Mode 5 (Fwd RC5) X 3 CDMA RECEIVER MINIMUM STANDARDS 3.1 Frequency Coverage Requirements 3.1.1 Band Class 0 (800 MHz band) X 3.1.2 Band Class 1 (1900 MHz band) X 3.1.3 Band Class 2 (TACS band) NA 3.1.4 Band Class 3 (JTACS band) NA 3.1.5 Band Class 4 (Korean PCS band) NA 3.1.6 Band Class 5 (NMT-450 band) NA 3.1.7 Band Class 6 (IMT-2000 band) NA 3.1.8 Band Class 7 (700 MHz cellular band) NA 3.1.9 Band Class 8 (1800 MHz band) NA 3.1.10 Band Class 9 (900 MHz band) NA 3.2 Acquisition Requirements 3.2.1 Idle Handoff Tests 3.2.1.1 Idle Handoff in Non-Slotted Mode on the Paging Channel X 3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel X 3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control

Channel X

3.2.1.4 Idle Handoff to Another Frequency X 3.2.2 Soft Handoff Tests 3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft

Handoff X

3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft Handoff X

3.2.2.38 Active Set Pilot Loss Detection in Soft Handoff X 3.2.3 Access and Access Probe Handoff Tests 3.2.3.1 Access Probe Handoff X

8 Test #3 of section 3.2.2.3.3 (of test #2) for pilot P2 only is not required.



TIA/EIA-98-E Section Description


= 6 Required in

Next Revision Required in

Future Revision

3.2.3.2 Access Handoff X 3.2.4 Candidate Frequency Single Search X 3.3 Forward Common Channel Demodulation Performance 3.3.1 Demodulation of Non-Slotted Mode Paging Channel X 3.3.2 Demodulation of Slotted Mode Paging Channel X 3.3.3 Demodulation of Broadcast Control Channel in AWGN

Channel X

3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading Channel X

3.3.5 Demodulation of Forward Common Control Channel X 3.3.6 Demodulation of Common Assignment Channel and

Reception of Common Power Control Channel X

3.4 Forward Traffic Channel Demodulation Performance 3.4.1 Demodulation of Forward Traffic Channel in Additive White

Gaussian Noise X

3.4.29 Demodulation of Forward Traffic Channel in Multipath Fading Channel X

3.4.3 Demodulation of Forward Traffic Channel During Soft Handoff X 3.4.4 Decision of Power Control Bit for Channels Belonging to

Different Power Control Sets During Soft Handoff X

3.4.5 Decision of Power Control Bit for Channels Belonging to the Same Power Control Set X

3.4.6 Demodulation of Power Control Subchannel During Soft Handoff X

3.4.7 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Closed Loop Power Control (FPC_MODE='000') X

3.4.8 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Closed Loop Power Control (FPC_MODE='010') X

3.4.9 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Outer Loop Power Control and Closed Loop Power Control (FPC_MODE='000', '001' and '010')

X


X


X

3.4.12 Demodulation of Power Control Subchannel During Reverse Pilot Channel Gating X

3.4.13 Demodulation of Power Control Subchannel During Reverse Fundamental Channel Gating X

3.5 Receiver Performance 3.5.1 Receiver Sensitivity and Dynamic Range X 3.5.2 Single Tone Desensitization X

9 Test # 12 in not required





= 6 Required in


Future Revision

3.5.3 Intermodulation Spurious Response Attenuation X 3.5.4 Adjacent Channel Selectivity X 3.5.5 Receiver Blocking Characteristics 3.6 Limitations on Emissions 3.6.1 (Rx) Conducted Spurious Emissions X; SFN 3.6.210 (Rx) Radiated Spurious Emissions X 3.7 Supervision 3.7.1 Paging Channel X 3.7.2 Forward Traffic Channel X 4 CDMA TRANSMITTER MINIMUM STANDARDS 4.1 Frequency Accuracy X; SFN 4.2 Handoff 4.2.1 CDMA to CDMA Hard Handoff X; SFN 4.2.2 Transmit Power After Hard Handoff X; SFN 4.3 Modulation Requirements 4.3.1 Time Reference X; SFN 4.3.2 Reverse Pilot Channel to Code Channel Time Tolerance X; SFN 4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance X; SFN 4.3.4 Waveform Quality and Frequency Accuracy X; SFN 4.3.5 Code Domain Power X; SFN 4.4 RF Output Power Requirements 4.4.1 Range of Open Loop Output Power X; SFN 4.4.2 Time Response of Open Loop Power Control X; SFN 4.4.3 Access Probe Output Power X; SFN 4.4.4 Range of Closed Loop Power Control X; SFN 4.4.511 Maximum RF Output Power X; SFN 4.4.6 Minimum Controlled Output Power X; SFN 4.4.7 Standby Output Power and Gated Output Power X; SFN 4.4.8 Power Up Function Output Power X; SFN 4.4.9 Code Channel to Reverse Pilot Channel Output Power

Accuracy X; SFN

4.4.9.2.1 Code Channel Output Power for the Enhanced Access Channel Header, Enhanced Access Channel Data, and Reverse Common Control Channel Data

X; SFN

4.4.9.2.212 Code Channel Output Power for the Reverse Traffic Channel X; SFN

4.4.10 Reverse Pilot Channel Transmit Phase Discontinuity X; SFN 4.4.11 Reverse Traffic Channel Output Power During Changes in

Data Rate X; SFN

10 This test is covered during FCC Compliance testing and therefore is not required to be performed by the CATL

11 When testing RC 3 + SCH, if the procedure outlined in TIA-98-E gives incorrect results, the CATL may use an alternate procedure for conducting this test

12 Data rates of 19,200 bps and above are not required





= 6 Required in


Future Revision

4.5 Limitations on Emissions 4.5.1 (Tx) Conducted Spurious Emissions X; SFN 4.5.213 (Tx) Radiated Spurious Emissions SFN

4.5.3 Occupied Bandwidth 5 Environmental Requirements 5.1 Temperature and Power Supply Voltage X 5.2 High Humidity X

5.3 Vibration Stability X

5.4 Shock Stability X

Appendix B.1.B – cdma2000 1x-EvDO Minimum Performance Tests IS-866


P_REV_IN_USE = 6


Required in Future

Revision 3.1.1.2.1 Demodulation of Forward Traffic Channel in AWGN X

3.1.1.2.2 Demodulation of Forward Traffic Channel in Multi-path Fading Channel X

3.1.1.2.3 Decision of Power Control Bit for Channels belonging to Different Power Control Sets during Soft Handoff X

3.1.1.2.4 Decision of Power Control Bit for Channels belonging to the Same Power Control Set X

3.1.1.2.5 Demodulation of Reverse Power Control Channel during Soft Handoff X

3.1.1.3.1 Receiver Sensitivity and Dynamic Range X; SFN 3.1.1.3.2 Single Tone Desensitization X 3.1.1.3.3 Intermodulation Spurious Response Attenuation X 3.1.1.3.4 Adjacent Channel Selectivity 3.1.1.3.5 Receiver Blocking Characteristics

Limitations on Emissions 3.1.1.4.1 Conducted Spurious Emissions X 3.1.1.4.2 Radiated Spurious Emissions

Transmitter Minimum Standards 3.1.2.1.2 Frequency Accuracy X; SFN

Modulation Requirements 3.1.2.2.1 Time Reference X; SFN 3.1.2.2.2 Waveform Quality and Frequency Accuracy X; SFN 3.1.2.2.3 Redundant ACK Transmission X; SFN

13 This test is covered during FCC Compliance testing and therefore is not required to be performed by the CATL for certification testing. For Safe-for-Network testing only, test results may be provided to the CATL by the product manufacturer (in such cases, the test results must be marked as provided by the product manufacturer).



IS-866 Section Description


= 6 Required in


Future Revision

RF Output Power Requirements 3.1.2.3.1 Range of Open Loop Output Power X; SFN 3.1.2.3.2 Time Response of Open Loop Power Control X; SFN 3.1.2.3.3 Range of Closed Loop Power Control X; SFN 3.1.2.3.4 Maximum RF Output Power X; SFN 3.1.2.3.5 Minimum Controlled Output Power X; SFN 3.1.2.3.6 Standby Output Power X; SFN 3.1.2.3.7 RRI Channel Output Power X; SFN

Code Domain Power 3.1.2.3.8.1 DRC Channel Output Power X; SFN 3.1.2.3.8.2 ACK Channel Output Power X; SFN 3.1.2.3.8.3 Data Channel Output Power X; SFN

Limitations on Emissions 3.1.2.4.1 Conducted Spurious Emissions X; SFN

Radiated Spurious Emissions 3.1.2.4.3 Occupied Bandwidth X; SFN

MAC Layer Minimum Standards 4.1.1.1 Control Channel Supervision X

Forward Traffic Channel MAC Protocol 4.2.1.1 Data Rate Control Performance X 4.2.1.2 Demodulation of Forward Traffic Channel during Soft Handoff X 4.2.1.3 Supervision Procedures in Variable Rate State X

Access Channel MAC Protocol 4.3.1.1 Access Probes Output Power X

Reverse Traffic Channel MAC Protocol 4.4.1.1 Reverse Traffic Channel Initial Transmit Power X 4.4.1.2 Reverse Traffic Channel Transmit Power X 4.4.1.3 Demodulation of the Reverse Activity Channel X 4.4.1.4 Reverse Traffic Channel MAC rate transition probabilities X

Key Exchange Protocol 5.1.1.1 Key Signature Computation time X

Idle State 6.1.1.1.1 Idle Handoff in Continuous Operation Mode X 6.1.1.1.2 Idle Handoff in Slotted Operation Mode X 6.1.1.1.3 Idle Handoff in Suspended Operation Mode X

Connected State

6.1.1.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft Handoff X

6.1.1.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft Handoff X

6.1.1.2.3 Active Set Pilot Loss Detection in Soft Handoff X 6.1.1.2.4 Hard Handoff to another Frequency X

Environmental Requirements 10.1 Temperature and Power Supply Voltage X 10.2 High Humidity X 10.3 Vibration Stability X 10.4 Shock Stability X



Appendix B.1.C – cdma2000 Position Location Minimum Performance Tests IS-916


P_REV_IN_USE = 6


Required in Future

Revision 2

GPS MINIMUM SPECIFICATION

2.1 GPS Performance Specifications

2.1.1 Stationary Location Tests

2.1.1.1 GPS Accuracy Test X; SFN

2.1.1.2 GPS Dynamic Range Test X; SFN

2.1.1.3 GPS Sensitivity Test X; SFN

2.1.1.4 GPS Multipath Accuracy Test X; SFN

2.1.2 Moving Scenario Test

2.1.2.1 Moving Scenario GPS Accuracy Test X; SFN

3 AFLT MINIMUM SPECIFICATION

3.2 AFLT Performance Specifications

3.2.1 AFLT Accuracy Test X; SFN

3.2.2 AFLT Sensitivity Test X; SFN

4 HYBRID MINIMUM SPECIFICATION

4.2 Hybrid Performance Specifications 4.2.1 One Base Station +Three Satellites Hybrid Test 4.2.2 Two Base Stations +One Satellite Hybrid Test X; SFN



Appendix B.2.A – cdma2000 Signaling Conformance Tests TIA/EIA-

898 Section Description


= 6 Required in Next

Revision Required in

Future Revision

1 Miscellaneous Air Interface Tests

1.1 Pilot PN Offset X

1.2 Hashing CDMA Channels, Paging Channels, and Paging Slot X

1.3 Idle Ping Pong with Quick Paging Channel CCI X

1.4 Quick Paging Indicator X

1.5 Mobile Station Processing of the Access Parameters Message X

1.6 Mobile Station Processing of MIN_P_REV X

1.7 Mobile Station Response to Status Request Message X

1.8 Protocol Discriminator (PD) Test and Link Access Control (LAC) PDU Format Test on the Access Channel X

1.914 Logging Tests X

1.10 SYNC Channel Support X

2 POTS Tests

2.1 Mobile Station Originated Call X; SFN

2.2 Mobile Station to Land Party Call, Radio Link Failure During Conversation -Reverse Link X

2.3 Mobile Station to Land Party, Radio Link Failure During Conversation -Forward Link X; SFN

2.4 Mobile Station Originated Call, Test Service Options X; SFN

2.5 Mobile Station to Land Party Call, Busy Tone X

2.6 Mobile Station to Land Party Call, No Traffic Channel Resources Available X

2.7 Mobile Station to Land Party Call, Reverse Link Failure During Call Setup X

2.8 Mobile Station to Land Party Call, Forward Link Failure During Call Setup X

2.9 Mobile Station Terminated Call X; SFN

2.10 Mobile Station terminated Call, Test Service Options X; SFN

2.11 Land Party to Mobile Station Call, Mobile Operating in Slotted Mode X; SFN

2.12 MSID, MCC, and IMSI X; SFN

2.13 TMSI Assignment

2.14 TMSI Expiration Time

2.15 Mobile Station to Land Party Call, DTMF X

2.16 Forward Traffic Channel DTMF Tone Signaling X

2.17 Enhanced DTMF Signaling X

2.18 Channel Assignment from CDMA to AMPS X

2.19 PACA Origination, User Terminates While Still In Queue

14 Tests 1.9.2.2, 1.9.3.2, 1.9.4.2 are not required



TIA/EIA-898

Section Description




Future Revision

2.20 PACA Origination, Idle Handoff While in Queue

2.21 PACA Origination, Traffic Channel Becomes Available

2.22 PACA Origination, Features Interaction

2.23 PACA Origination, Permanent Invocation

2.24 PACA Origination, PACA Disabled for Mobile Station

2.25 True IMSI Support X

2.26 Initial Service Configuration and Negotiation X

2.27 Base Station Requested Service Negotiation (Successful Scenarios) X

2.28 Base Station Reject Scenarios during Service Negotiation X

2.29 Mobile Station Reject Scenarios during Service Negotiation X

2.30 Service Negotiation Completion via General Handoff Direction Message and Universal Handoff Direction Message X

2.31 SCR without NN-SCR and NN-SCR without SCR in General Handoff Direction Message and Universal Handoff Direction Message X

2.32 Base Station Request Overrides the Mobile Station Request X

2.33 Service Negotiation Involving Partial SCR and/or Partial NN-SCR X

2.34 Quasi-Orthogonal Functions (QOF) assignment X

2.35 Release Order on Access Channel X

3 Handoff Tests

3.1 Soft Handoff with Dynamic Threshold X

3.2 Hard Handoff Between Frequencies in the Same Band Class X; SFN

3.3 Hard Handoff from CDMA to AMPS X

3.4 Soft Handoff in Fading X

3.5 Hard Handoff in Fading X

3.6 Hard Handoff Between Different Band Classes X; SFN

3.7 Hard Handoff with and without Return on Failure X

3.8 Search Window Size and Offset Per Neighbor X

3.9 Access Handoffs X

3.10 Traffic Channel Preamble during Hard Handoff Between Frequencies in same band X

3.11 Hopping Pilot Beacon

3.12 Hard Handoff Between Frequencies with Different Radio Configurations X

3.13 Handoff on Same Frequency with Different Radio Configurations X

3.14 Hard Handoff while in the Waiting for Mobile Station Answer Substate X

3.15 Inter-Frequency Hard Handoff (CDMA to CDMA) X

3.16 Inter-Frequency Hard Handoff (CDMA to AMPS) X

3.17 Hard Handoff Between Frequencies with Different Protocol Revisions X

4 Power Control Tests

4.1 Forward Traffic Channel Power Control X

4.2 Mobile Station Response to Power Up Function (PUF) Message

4.3 Fast Forward Power Control (FFPC) X

5 Registration Tests



TIA/EIA-898

Section




Future Revision Description

5.1 Power-Up Registration X; SFN

5.2 Power-Down Registration X; SFN

5.3 Timer-Based Registration X; SFN

5.4 Distance-Based Registration X; SFN

5.5 Zone-Based Registration X; SFN

5.6 Parameter-Change Registration X; SFN

5.7 Registration Under Various Settings of MOB_TERM X; SFN

6 Authentication Tests

6.1 Shared Secret Data Initialized to Zero X

6.2 Shared Secret Data Update on the Paging/Access Channels X

6.3 Shared Secret Data Update on the Forward/Reverse Traffic Channels X

6.4 Mismatched A-Keys X

6.5 Activating Voice Privacy on Call Setup X

6.6 Activating Voice Privacy at the Mobile Station When a Call Is Active X

6.7 Signaling Message Encryption on Forward Traffic Channel (Alert with Information Message) X

6.8 Signaling Message Encryption on Reverse Traffic Channel (Burst DTMF Message) X

6.9 Hard Handoffs between Base Stations with SME Active. X

6.10 Signaling Message Encryption Mobile Terminated SMS (Data Burst Message) X

6.11 Authentication Upon Originations X

6.12 Hard Handoff from CDMA to AMPS with SME Active X

7 Service Redirection

7.1 Global Service Redirection Tests X

7.2 Network Directed System Selection and Normal Service Redirection Tests X; SFN

7.3 Extended Global Service Redirection Tests X; SFN

8 Short Message Service (SMS)

8.1 Mobile Station Terminated SMS Tests X

8.215 Mobile Station Originated SMS Tests X

8.3 Broadcast SMS Tests

9 Subscriber Calling Features Tests

9.1 Call Forwarding X

9.2 Three-Way Calling X

9.3 Land Party to Mobile Station Caller ID X

9.4 X

9.5 Message Waiting Indicator (MWI) X

9.616 Land Party to Mobile Station Calling Name Presentation X

Call Waiting

15 Tests 8.2.4, 8.2.5, and 8.2.6 are not required



TIA/EIA-898

Section Description




Future Revision

9.7 Display Records X

9.8 TTY/TDD X

9.9 Answer Holding X

9.10 User Selective Call Forwarding X

10 Asynchronous Data and Fax Services

10.1 Send/Receive Fax X

10.2 Upload/Download Binary File X

10.3 Simultaneous Two-way File Transfer/Carrier Detect X

10.4 Compound AT Command, Initialization and Connection Delay X

10.5 Escaping to Command Mode X

10.6 Air Interface Data Compression X

10.7 RLP Operation in a Poor RF Environment X

10.8 RLP Abort and TCP Retransmit Test X

10.9 Internet Control Message Protocol (ICMP) Requests/Replies X

10.10 Reflection of AT Command Parameters X

11 Packet Data Services Tests

11.1 Terminal Session with Remote Host

11.2 File Transfer

11.3 IP Address Negotiation

11.4 V-J Header Compression

11.5 Asynchronous Control Character Mapping (ACCM) Negotiation

11.6 PPP Field Compression

11.7 Maximum Receive Unit (MRU)

11.8 Mobile Station Inactivity Timer

11.9 IWF Inactivity Timer

11.10 Radio Link Protocol (RLP) Operation in Rayleigh Fading

11.11 RLP Abort and Upper Layer Retransmit

11.12 RLP Encryption Negotiation

11.13 Hardware Flow Control X

11.14 Re-connect after Hard Handoff

11.15 Zone-Based Registration for Packet Data Mobile Stations

12 Medium-Speed Packet Data

12.1 Forward File Transfer with Fundamental and Supplemental Code Channels NA

12.2 Forward File Transfer with Variable Supplemental Code Channels NA

12.3 MSPD Call Setup, No Negotiation

12.4 MSPD Call Setup, Negotiation to a Different MSPD Service Option

12.5 MSPD Call Setup, Negotiation to LSPD

16 Test 9.6.2 and 9.6.3 are not required



TIA/EIA-898

Section Description




Future Revision

12.6 MSPD Call Setup, Mobile Station Maximum Multiplex Option Less than Base Station Maximum Multiplex Option

12.7 MSPD Call Setup, Mobile station Maximum Multiplex Option Greater than Base Station Maximum Multiplex Option

12.8 Allocation/De-allocation of Supplemental Code Channels NA

12.9 No Transmission on Supplemental Code Channels NA

12.10 Soft Handoff with Supplemental Code Channels NA

12.11 Adding Supplemental Code Channels during Soft Handoff NA

12.12 Hard Handoff to an MSPD-Capable System

12.13 RLP Operation in Rayleigh Fading Environment

12.14 RLP Operation with Severely Degraded Channel

12.15 Bi-Directional File Transfers with Forward Supplemental Code Channels NA

12.16 Rм Interface Flow Control

12.17 Dormant Timer

12.18 Packet Zone ID

13 High Speed Packet Data

13.1 Forward File Transfer X

13.2 Reverse File Transfer X

13.3 Bi-directional File Transfer X

13.4 Basic Supplemental Channel Configuration Setting and Single Assignment X

13.5 Supplemental Channel Multiple Assignments X

13.6 Turbo Coding on Supplemental Channel

13.7 Correct Walsh Cover

13.8 Supplemental Channel Discontinuous Transmission X

13.9 Slotted Timer

13.10 Retry Order and Delay for Origination Message

13.11 Retry Order and Delay for Supplemental Channel Request Messages

13.12 Retry Order and Delay for Resource Request Messages

13.13 Base Station Initiated Active to Control Hold Mode Transitions X

13.14 Mobile Station Initiated Active to Control Hold Mode Transitions

13.15 Base Station Initiated Control Hold to Active Mode Transitions X

13.16 Mobile Station Initiated Control Hold to Active Mode Transitions X

13.17 Base Station Ignores Mobile Station Requested Mode Transitions

13.18 Mobile station Multiplex Option different from Base Station Multiplex Option X

13.19 Soft Handoff of Fundamental Channel and Supplemental Channels X

13.20 Soft Handoff of Fundamental Channel only X

13.21 Adding Supplemental Channels during Soft Handoff X

13.22 Hard Handoff to HSPD-capable system X

13.23 Hard Handoff from MSPD to HSPD

13.24 Hard Handoff from LSPD to HSPD

13.25 Hard Handoff to a different RC X



TIA/EIA-898

Section Description




Future Revision

13.26 Mobile Station Aborts R-SCH

13.27 RLP Operation in Rayleigh Fading Environment X

13.28 RLP Operation in Severely Degraded Channel X

13.29 Mobile Station Originated Short Data Burst X

13.30 Mobile Station Terminated Short Data Burst X

13.31 Mobile Assisted Burst Operation Parameters Message Test

13.32 Mobile Station and Base Station Operating in Different States X

Data Services Tests Annex

14 Over-The-Air Services

14.1 OTASP Service Request Processing X

14.2 OTAPA Service Request Processing for a Mobile Station in Mobile Station Idle State X

14.3 OTAPA Service Request Processing for a Mobile Station in Conversation Substate

X

14.4 OTAPA Service Request Processing Interrupted by User Action X

15 System Selection for Preferred Roaming

15.1 OTASP Service Provisioning For System Selection and Preferred Roaming X

15.2 Non-Acquisition of a System on Negative Preferred Roaming List (PRL) X

15.3 Emergency Call On a System that is Negative on PRL or SID List X

15.4 OTASP For System Selection and Preferred Roaming - Oversize PRL X

15.5 OTAPA Service Provisioning for System Selection and Preferred Roaming for a Mobile Station in Mobile Station Idle State X

16 Message Driven Indicators

16.1 Enhanced Roaming Indicator X

17 Forward Compatibility Tests

17.1 Sync Channel

17.2 Paging Channel

17.3 Traffic Channel

TBD17 Mobile Station Inactivity Timer X

TBD18 Rм Interface Flow Control X

TBD19 Dormant Timer X

TBD20 Packet Zone ID X

17 This test is equivalent to test 11.8, but repeated for SO 33






Appendix B.2.B – cdma2000 Wireless IP Signaling Conformance Tests

TIA/EIA- 918 Section Number

Description RequiredRequired in

Next Revision

Required in Future

Revision

3 Simple IP Tests

3.1 Simple IP Establishment without Authentication of the Mobile Station X

3.2 Simple IP Establishment with CHAP X

3.3 Simple IP Establishment with PAP X 4 Agent Discovery and Registration 4.1 Successful PPP Negotiation and Termination X

4.2 Agent Discovery and Registration using Dynamic Home Address Assignment Successful Scenario X

4.3 Agent Discovery and Registration using Static Home Address Assignment Successful Scenario X

4.4 Router Advertisement Lifetime Expires X

4.5 Mobile Station Registration Request Failed HA has Insufficient Resources X

4.6 Mobile Station Registration Request Retry X 4.7 Registration Lifetime Processing X 4.8 Timestamp Error X 4.9 Mobile Station De-Registers X 4.10 Simultaneous Simple IP and Mobile IP X 5 Handoffs 5.1 Inter-PDSN Handoff Mobile Station in Active State X

5.2 Inter-PDSN handoff Mobile Station in dormant State X

5.3 Intra-PDSN Handoff Mobile Station in Active State X

5.4 Intra-PDSN Handoff Mobile Station in dormant State X

5.5 Simple IP Inter-PDSN Idle Handoff X

5.6 Simple IP Intra-PDSN Handoff Mobile Station in dormant State X

6 Authentication and IPsec Security Association Support

6.1 RADIUS Support Successful Scenario 6.2 RADIUS Support Unsuccessful Scenario X

6.3 IPSec Security Support Preserving of Existing Security Association

6.4 Authehntication Failure MN-HA Authenticator is Invalid X

6.5 Foreign Agent Reverse Tunnel Registration Behavior X

6.6 Private Network Support Successful Scenario X





Next Revision

Required in Future

Revision

6.7 Private Network Support Unsuccessful Scenario X

6.8 Successful Authentication using the MN-AAA Extension

7 Network Specific Tests

7.1 Mobile IP Registration Request with Invalid Extensions

7.2 Foreign Agent Busy

7.3 Mobile IP Registration Request Rejected Invalid Home Address X

7.4 Registration Rejected by FA Poorly Formed Request

7.5 Registration Rejected by Home Agent Administratively Prohibited X

7.6 Agent Advertisements not sent to Mobile Station using Simple IP

7.7 Mobile IP Registration Expires

7.8 Mobile IP Registration Request Lifetime Exceeds Agent Advertisement Lifetime

7.9 Multiple Home Addresses X

7.10 Mobile Station Assigned Same Home Address By Two Home Agents X

7.11 Ingress Address Filtering

7.12 IPsec Security Support Statically Configured IKE Pre-Shared Secret

7.13 IP Security Support Dynamically Configured IKE Pre-Shared Secret

7.14 Security Association using Public X.509 Certificates

7.15 Security Association using the Root X.509 Certificates

7.16 Unsuccessful IPsec Security Association Establishment

7.17 PDSN Clears PPP State R-P Session Closed X

7.18 PDSN Terminates Simple IP Session Due to PDSN PPP Inactivity Timer Expiration X

7.19 PDSN Terminates a Simple IP Session when the R-P Session is Closed

8 Accounting

8.1 Accounting Scenario without Containers and No Change in Multiplex Options User Zone or QoS

8.2 Accounting Scenario with Containers and a Change in Multiplex Options User Zone or QoS

8.3 Accounting Scenario without Containers and a Change in Multiplex Options User Zone or QoS

8.4 Multiple Home Agent Test with Accounting





Next Revision

Required in Future

Revision

8.5 Single Home Agent and Simple IP Test with Accounting

8.6 HDLC Byte Accounting Test with Simple IP 8.7 Simple IP Test with Accounting and CHAP 8.8 Simple IP Test with Accounting and PAP

Appendix B.2.C – cdma2000 1x-EvDO Signaling Conformance Tests IS-919 Reference Test Case Name Required

Default Signaling Application Tests Default Signaling Network Protocol Tests Access Network Tests SNP Header Test Minimum Standard Access Terminal Tests SNP Header Test Minimum Standard Default Signaling Link Protocol Tests Access Network Tests SLP Initialization Test SLP-D Sequence Number Increment Tests Reliable-Delivery SLP-D Packet Transmission Test

Reliable-Delivery SLP-D Packet Acknowledgment Test

2.2.1.5 Retransmission of Unacknowledged Reliable-Delivery SLP-D Packet Test

2.2.1.6 Successful Reassembly of SLP-F Packets Sent on the Access Channel Test

Successful Reassembly of SLP-F Packets Sent on the Reverse Traffic Channel Test

Access Terminal Tests 2.2.2.1 SLP Initialization Tests X 2.2.2.2 SLP Reset Test X 2.2.2.3 SLP-D Sequence Number Increment Test X

2.2.2.4 Reliable-Delivery SLP-D Packet Transmission Test

Reliable-Delivery SLP-D Packet Acknowledgement Test X

2.2.2.6 Retransmission of Unacknowledged Reliable-Delivery SLP-D Packet Test X

2.2.2.7 Successful Reassembly of SLP-F Packets Sent on the Forward Traffic Channel Test X

Required in Next

Revision

Required in Future

Revision 2 2.1 2.1.1 2.1.1.1 2.1.1.2 2.1.2 2.1.2.1 2.1.2.2 2.2 2.2.1 2.2.1.1 2.2.1.2

2.2.1.3

2.2.1.4

2.2.1.7

2.2.2

2.2.2.5



IS-919 Reference Required

Required in Next

Revision

Required in Future

Revision

2.2.2.8 Successful Reassembly of Fragmented Broadcast Messages on the Control Channel Test X

2.2.2.9 Successful Reassembly of Fragmented Unicast Messages on the Control Channel Test X

3 Default Packet Application Tests 3.1 Radio Link Protocol Tests 3.1.1 Access Network RLP Tests 3.1.1.1 RLP Initialization Test

RLP Sequence Number Increment Test 3.1.1.3 RLP Reset Test 3.1.1.4 RLP NAK Test 3.1.1.5 RLP Synchronization Loss Detection Test 3.1.1.6 Basic File Transfer Test 3.1.2 Access Terminal RLP Tests 3.1.2.1 RLP Initialization Test X 3.1.2.2 RLP Sequence Number Increment Test X 3.1.2.3 RLP Reset Test X 3.1.2.4 RLP NAK Test X 3.1.2.5 RLP Synchronization Loss Detection Test X 3.1.2.6 Basic File Transfer Test X 3.2 Location Update Protocol Tests

Access Network Tests Access Terminal Tests

3.2.2.1 LocationRequest Message Response Test X Flow Control Protocol Tests

3.3.1 Access Network Tests XonRequest and XoffRequest Message Response Test X

3.3.2.1 DataReady Message Response Test X 4 Stream Layer Protocol Tests 4.1 Default Stream Protocol Tests 4.1.1 Access Network Tests 4.1.1.1 Stream Layer Header Tests

Stream 0 Binding to the Default Signaling Application Test

4.1.1.3 ConfigurationRequest Message Response Test 4.1.2 Access Terminal Tests 4.1.2.1 Stream Layer Header Tests

Stream 0 Binding to the Default Signaling Application Test

4.1.2.3 ConfigurationRequest Message Response Test X 5 Session Layer Tests 5.1 Default Session Management Protocol Tests 5.1.1 Access Network Tests

Test Case Name

3.1.1.2

3.2.1 3.2.2

3.3

3.3.1.1

3.3.2 Access Terminal Tests

4.1.1.2

4.1.2.2



IS-919 Reference Test Case Name

Required in Next

Revision

Required in Future

Revision 5.1.1.1 KeepAliveRequest Message Response Test 5.1.1.2 ConfigurationRequest Message Response Test 5.1.2 Access Terminal Tests 5.1.2.1 KeepAliveRequest Message Response Test X 5.1.2.2 SessionClose Message Response Test X 5.1.2.3 ConfigurationRequest Message Response Test X 5.2 Default Address Management Protocol Tests 5.2.1 Access Network Tests

5.2.1.1 Recognition of Dual Addresses during Address Assignment Test

5.2.1.2 ConfigurationRequest Message Response Test X 5.2.2 Access Terminal Tests 5.2.2.1 Purging of RATI after Session Establishment Test X

5.2.2.2 Idle State Response to Subnet/Sector Change Test X

5.2.2.3 AT Response to a Change in the Serving Sector Test X

5.2.2.4 Idle State UATIAssignment Message Response Test X

5.2.2.5 Connected State UATIAssignment Message Response Test X

5.2.2.6 HardwareIDRequest Message Response Test X X

5.2.2.8 ConfigurationRequest Message Response Test X

5.3.1 Access Network Tests

ConfigurationComplete Message Response Test

ConfigurationRequest Message Response Test X ConfigurationComplete Message Response Test X Connection Layer Tests

Access Network Tests

Access Terminal Tests Redirect Message Test X ConfigurationRequest Message Response Test X Default Initialization State Protocol Tests

Sync Message Transmission Test X

Access Terminal Tests Network Determination Test X System Acquisition Test X

Required

5.2.2.7 AT Idle State Address Timer Operation Test

5.3 Default Session Configuration Protocol Tests

5.3.1.1 ConfigurationRequest Message Response Test 5.3.1.2 5.3.2 Access Terminal Tests 5.3.2.1 5.3.2.2 6 6.1 Default Air-Link Management Protocol Tests 6.1.1 6.1.1.1 ConfigurationRequest Message Response Test 6.1.2 6.1.2.1 6.1.2.2 6.2 6.2.1 Access Network Tests 6.2.1.1 6.2.1.2 ConfigurationRequest Message Response Test 6.2.2 6.2.2.1 6.2.2.2



IS-919 Reference Test Case Name Required

Required in Next

Revision

Required in Future

Revision AT Processing of MinimumRevision and MaximumRevision Fields in the Sync Message Test

6.2.2.4 ConfigurationRequest Message Response Test X 6.3 Default Idle State Protocol Tests

Access Network Tests

X

6.3.1.2 ConfigurationRequest Message Response Test 6.3.2 Access Terminal Tests 6.3.2.1 AT Slotted Mode Operation Test X 6.3.2.2 X 6.3.2.3 AN Initiated Fast Connection Setup Test X 6.3.2.4 ConfigurationRequest Message Response Test X

Default Connected State Protocol Tests Access Network Tests ConfigurationRequest Message Response Test Access Terminal Tests ConnectionClose Message Response Test X ConfigurationRequest Message Response Test X

6.5 Default Route Update Protocol Tests Access Network Tests ConfigurationRequest Message Response Test Access Terminal Tests AT Idle State Distance Based Route Update Message Test X

TrafficChannelAssignment Message Response Test X

X

6.7.1 Access Network Tests

QuickConfig Message Transmission Test 6.7.1.2 SectorParameters Message Transmission Test 6.7.1.3 ConfigurationRequest Message Response Test 6.7.2 Access Terminal Tests 6.7.2.1 ConfigurationRequest Message Response Test X 7 Security Layer Tests 7.1 DH Key Exchange Protocol Tests 7.1.1 Access Network Test 7.1.1.1 DH Key Exchange Protocol Negotiation Test 7.1.2 Access Terminal Test 7.1.2.1 DH Key Exchange Protocol Negotiation Test X

6.2.2.3 X

6.3.1

6.3.1.1 Page Message Transmissions to an Access Terminal Operating in Slotted Mode Test

AT Monitor State CDMA Channel Selection Test

6.4 6.4.1 6.4.1.1 6.4.2 6.4.2.1 6.4.2.2

6.5.1 6.5.1.1 6.5.2

6.5.2.1

6.5.2.2

6.5.2.3 ConfigurationRequest Message Response Test 6.6 Default Packet Consolidation Protocol Tests 6.6.1 Access Network Test 6.6.2 Access Terminal Tests 6.7 Overhead Messages Protocol Tests

6.7.1.1



IS-919 Reference

Required in Next

Revision

Required in Future

Revision 7.2 SHA-1 Authentication Protocol Tests 7.2.1 Access Network Test 7.2.1.1 SHA-1 Authentication Protocol Negotiation Test 7.2.2 Access Terminal Test 7.2.2.1 SHA-1 Authentication Protocol Negotiation Test X 7.3 Security Protocol Tests 7.3.1 Access Network Test

7.3.1.1 SecurityLayerFormat Field in the Control Channel MAC Packet Header Test

7.3.2 Access Terminal Test

7.3.2.1 SecurityLayerFormat Field in the Access Channel MAC Packet Header Test X

8 Mac Layer Tests 8.1 Default Control Channel MAC Protocol Tests 8.1.1 Access Network Test

8.1.1.1 Control Channel Header Fields in Synchronous Capsule Test X

8.1.1.2 ConfigurationRequest Message Response Test 8.1.2 Access Terminal Test 8.1.2.1 ConfigurationRequest Message Response Test X 8.2 Default Access Channel MAC Protocol Tests 8.2.1 Access Network Tests 8.2.1.1 X 8.2.1.2 ConfigurationRequest Message Response Test 8.2.2 Access Terminal Tests 8.2.2.1 ConfigurationRequest Message Response Test X

8.3 Default Forward Traffic Channel MAC Protocol Tests

8.3.1 Access Network Tests 8.3.1.1 FixedModeEnable Message Response Test X 8.3.1.2 ConfigurationRequest Message Response Test 8.3.2 Access Terminal Tests 8.3.2.1 ConfigurationRequest Message Response Test X

8.4 Default Reverse Traffic Channel MAC Protocol Tests

8.4.1 Access Network Tests 8.4.1.1 ConfigurationRequest Message Response Test 8.4.2 Access Terminal Tests 8.4.2.1 ConfigurationRequest Message Response Test X TBD Different periodicity of control messages X

Test Case Name Required

AccessParameters Message Transmission Test



Appendix B.2.D – cdma2000 1x-EvDO Wireless IP Signaling Conformance Tests



Next Revision

Required in Future

Revision

3 Simple IP Tests Simple IP Establishment without Authentication of the Mobile Station

X

Simple IP Establishment with CHAP X

3.3 Simple IP Establishment with PAP X 4 Agent Discovery and Registration 4.1 Successful PPP Negotiation and Termination X 4.2 Agent Discovery and Registration using Dynamic

Home Address Assignment Successful Scenario X

4.3 Agent Discovery and Registration using Static Home Address Assignment Successful Scenario

X

4.4 Router Advertisement Lifetime Expires X 4.5 Mobile Station Registration Request Failed HA

has Insufficient Resources X

4.6 Mobile Station Registration Request Retry X 4.7 Registration Lifetime Processing X 4.8 Timestamp Error X 4.9 Mobile Station De-Registers X 4.10 Simultaneous Simple IP and Mobile IP X 5 Handoffs 5.1 Inter-PDSN Handoff Mobile Station in Active State 5.2 Inter-PDSN handoff Mobile Station in dormant

State X

5.3 Intra-PDSN Handoff Mobile Station in Active State X 5.4 Intra-PDSN Handoff Mobile Station in dormant

State X

5.5 Simple IP Inter-PDSN Idle Handoff X 5.6 Simple IP Intra-PDSN Handoff Mobile Station in

dormant State X

6 Authentication and IPsec Security Association

Support

6.1 RADIUS Support Successful Scenario 6.2 RADIUS Support Unsuccessful Scenario X 6.3 IPSec Security Support Preserving of Existing

Security Association

6.4 Authentication Failure MN-HA Authenticator is Invalid

X

3.1

3.2





Next Revision

Required in Future

Revision

6.5 Foreign Agent Reverse Tunnel Registration Behavior

X

6.6 Private Network Support Successful Scenario X 6.7 Private Network Support Unsuccessful Scenario X 6.8 Successful Authentication using the MN-AAA

Extension

7 Network Specific Tests 7.1 Mobile IP Registration Request with Invalid

Extensions

7.2 Foreign Agent Busy 7.3 Mobile IP Registration Request Rejected Invalid

Home Address X

7.4 Registration Rejected by FA Poorly Formed Request

7.5 Registration Rejected by Home Agent Administratively Prohibited

X

7.6 Agent Advertisements not sent to Mobile Station using Simple IP

7.7 Mobile IP Registration Expires 7.8 Mobile IP Registration Request Lifetime Exceeds

Agent Advertisement Lifetime

7.9 Multiple Home Addresses X 7.10 Mobile Station Assigned Same Home Address By

Two Home Agents X

7.11 Ingress Address Filtering 7.12 IPsec Security Support Statically Configured IKE

Pre-Shared Secret

7.13 IP Security Support Dynamically Configured IKE Pre-Shared Secret

7.14 Security Association using Public X.509 Certificates

7.15 Security Association using the Root X.509 Certificates

7.16 Unsuccessful IPsec Security Association Establishment

7.17 PDSN Clears PPP State R-P Session Closed 7.18 PDSN Terminates Simple IP Session Due to

PDSN PPP Inactivity Timer Expiration X

7.19 PDSN Terminates a Simple IP Session when the R-P Session is Closed

8 Accounting 8.1 Accounting Scenario without Containers and No

Change in Multiplex Options User Zone or QoS

X





Next Revision

Required in Future

Revision

8.2 Accounting Scenario with Containers and a Change in Multiplex Options User Zone or QoS

8.3 Accounting Scenario without Containers and a Change in Multiplex Options User Zone or QoS

8.4 Multiple Home Agent Test with Accounting 8.5 Single Home Agent and Simple IP Test with

Accounting

8.6 HDLC Byte Accounting Test with Simple IP 8.7 Simple IP Test with Accounting and CHAP 8.8 Simple IP Test with Accounting and PAP

Appendix B.2.E – cdma2000 Position Location Signaling Conformance Tests IS-916

Section Description Required

Required in Next

Revision

Required in Future

Revision 2 GPS Minimum Specifications 2.2 GPS Protocol Tests

2.2.1 GPS Position Location Session on the Paging Channel Test X

2.2.2 Mobile Station Originated GPS Position Location Test

2.2.2.1 Mobile Station Originated GPS Position Location Session on the Access Channel X

2.2.2.2 Mobile Station Originated GPS Position Location Session on the Dedicated Channel X

3 AFLT Minimum Specification 3.3 AFLT Protocol Tests

3.3.1 AFLT Position Location Session on the Paging Channel Test X

3.3.2 Mobile Station Originated AFLT Position Location Test

3.3.2.1 Mobile Station Originated AFLT Position Location Session on the Access Channel X

3.3.2.2 Mobile Station Originated AFLT Position

Location Session on the Dedicated Channel

X



Appendix B.3.A – cdma2000 CDG35 Handset Stability and Performance Tests CDG Ref 35

Section System Performance Test Required

Required in Next

Revision

Required in Future

Revision 1 Audio Quality Tests

1.1 Acoustic Dropouts in Hard Handoffs X

1.2 Acoustic Time Delay X

1.3 MOS (Mean Opinion Score) Predictive Test X

1.4 System Frequency Response Test X

1.5 Frame Error Rate

2 Mobile Station Talk time/Standby Time Tests

2.1 Mobile Station Talk Time X

2.2 Mobile Station Standby Time X

3 Reserved

4 Preferred Roaming List TESTS

4.1 Preferred Roaming List, Positive Entry Test X

4.2 Emergency Call On a System that is Negative on PRL X

4.3 System Acquisition X

4.4 OTASP For System Selection and Preferred Roaming - Oversize PRL

4.5 OTASP For System Selection and Preferred Roaming - PRL Upgrade with Shorter List



Appendix B.3.B – cdma2000 CDG64 Handset Stability and Performance Tests CDG Ref 64

Section System Performance Test Required

Required in Next

Revision

Required in Future

Revision 4.1 System Acquisition and Registration

4.1.1 System Acquisition and Power-Up Registration

4.1.2 Power-Down Registration

4.1.3 System Acquisition from a Less Preferred System X

4.2 Successful Access

4.2.1 Mobile Originated Call Success Rate

4.2.2 Mobile Terminated Call Success Rate

In-Call Drive Tests

4.3.1 Long Call Maintenance with Handoffs and Fading

Idle State Drive Tests

Slotted Mode with Idle Handoffs and Registrations

Service Redirection

4.5 SMS

SMS Mobile Terminated in Idle State

SMS Mobile Originated from Idle State

4.5.3 SMS While in a Call

SMS Message Undeliverable

SMS Reply Option X

Subscriber Calling Features

Waiting

4.6.2 3-Way Calling

4.6.3 Caller ID

4.6.4 Call Forwarding

4.6.5 DTMF

4.6.6 TTY

4.6.7 Voice Privacy

4.6.8 CDMA Authentication

4.7 Voice Mail

4.7.1 Voice Mail Notification

4.7.2 Voice Mail Retrieval

4.7.3 No Answer with Release Order

4.8 OTA Provisioning and Maintenance

4.8.1 OTA Service Activation

4.8.2 OTA PRL Update

4.3

4.4

4.4.1

4.4.2

4.5.1

4.5.2

4.5.4

4.5.5

4.6

4.6.1 Call



CDG Ref 64 Section System Performance Test Required

Required in Next

Revision

Required in Future

Revision 4.9 Mini-Browser

4.9.1 Mini-Browser Access in 3G (CDMA2000)

4.9.2 Mini-Browser Access in 2G (IS-95)

4.9.3 Mini-Browser Handoffs Between 2G and 3G

4.10 HSPD Tests

4.10.1 HSPD Basic Connection to the Internet X

4.10.2 HSPD File Transfer Data Rate

4.10.3 HSPD Drive Test

4.10.4 HSPD PPP or IP Expiration X

4.10.5 HSPD Mobile IP PDSN Hard Handoff

4.10.6 HSPD Mobile IP PDSN Dormant Idle Handoff

4.10.7 HSPD Ping while Dormant X

4.10.8 HSPD Call Drop or Temporary Loss of Service X

4.10.9 HSPD and Voice Calls X

4.10.10 HSPD and SMS X

4.11 Asynchronous Data and Fax

4.11.1 Initialization and Connection Delay

4.11.2 Mobile Origination and Speaker On Until Connect

4.11.3 Send/Receive Fax

4.11.4 Upload/Download Binary File

4.12 AMPS

4.12.1 Hard Handoff from CDMA to AMPS

4.12.2 Service Redirection from CDMA to AMPS



This page intentionally left blank




Appendix C – Safe-For-Network Test Report Format

cdmaOne Terminal Version Terminal Hardware Type Terminal SW Version IS-98-E Section

# Test

Description Test

Result Comments

CDMA2000 Terminal Version Terminal Hardware Type Terminal SW Version IS-98-E Section

# Test

Description Test

Result Comments

CDMA2000 1xEV-DO Terminal Version Terminal Hardware Type Terminal SW Version IS-866

Section #

Test Description

Test Result Comments

CDMA2000 Position Location Terminal Version Terminal Hardware Type Terminal SW Version IS-916

Section #

Test Description

Test Result Comments

Ctia Cdma Test Plan Rev 4.0

Documents

ctia test plans

ctia certification department

test laboratories

ctias test plan

test overview

test process

test mobile station

cdma mobile stationsapril