This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
LODI, CA810 S. Cluff AvenueLodi, CA 95240-3141800-344-3270209-333-4680FAX: 209-333-4678
®
Distributed By:
D E S C R I P T I O N
B A S I C U S E
I N S T A L L A T I O N I N S T R U C T I O N S
P A C K A G I N G I N F O R M A T I O N
Easyrod is an extremely strong and quick alternative method for theinstallation of tie rod reinforcements into ductwork. Threadedinserts are applied to the inside of EMT conduit to insure fast andconsistent installation of internal reinforcements.
Drill clearance hole for 1/4" bolt (9/32" typ.) through top andbottom of duct panels at desired location. Cut 1/2" or 3/4" EMTconduit to duct size. Apply Easyrod insert onto installation tool,prongs toward installation tool. Drive an Easyrod insert into eachend of conduit. Place conduit through open end of duct to drilledhole location. Fasten bolt through galvanized neoprene washer andthrough drilled hole into Easyrod insert. Tighten both ends untilsnug (Do not overtighten). Result: a leak free installation requiring no extra sealing.
The Easyrod set consists of one of each of the following components:
1/2" or 3/4" Easyrod insert1/4" I.D. x 1" O.D. galvanized neoprene bonded washer1/4" x 1" N.C., Gr. 5, plated hex bolt
An Easyrod tool is also available to simplify and reduce assemblytime.
S P E C I A L C H A R A C T E R I S T I CPull out rated -900 lbs.
Easyrod can be used wherever internal tie rods are needed withinthe duct system.
P R O D U C T G U A R A N T E E
Easyrod is guaranteed against defective material.
BoltPipe insert is friction fittedwith internal threads
Stamped, galvanized discwith neoprene washersecures the ductwall.
Light Wall conduit Duct wall
D E S C R I P T I O N
B A S I C U S E
I N S T A L L A T I O N I N S T R U C T I O N S
P A C K A G I N G I N F O R M A T I O N
Easystud is a faster alternative method for the installation of tie rodreinforcements into ductwork. Threaded stud inserts are applied tothe inside of EMT conduit to insure fast and consistent installation ofinternal reinforcements.
Drill a clearance hole for 1/4" bolt (9/32" typ.) bolt through boththe top and bottom of the duct panels at the desired location for thereinforcement. Cut a length of 1/2" EMT conduit to the size of theductwork. Apply an Easystud insert onto the installation tool, withthe prongs facing the tool. Drive an Easystud insert into each end ofthe conduit. Position the conduit in the ductwork with the twoEasystud inserts protruding through the predrilled holes in the duct.Apply the washer and bolt to both ends of the Easystud inserts.Tighten both ends until snug (Do not over tighten) Result: a leak free installation requiring no extra sealing.
The Easystud set consists of one of each of the following components:
An Easystud tool is also available to simplify and reduce assemblytime.
S P E C I A L C H A R A C T E R I S T I CPull out rated - 600 lbs.
Easystud can be used wherever internal tie rods are needed withinthe duct system.
P R O D U C T G U A R A N T E E
Easystud is guaranteed against defective material.
Nut
Light Wall conduit Duct wall
Washer
Pipe insert is frictionfitted with threaded rod permanently attached
Stamped, galvanizeddisc with neoprene washer secures the ductwall
EASYROD/EASYSTUD
BY DUCTMATE INDUSTRIES
Easystud/Easyrod reinforces ductwork
by inserting threaded studs in EMT
conduit for consistent installation in
positive or negative pressure
applications. Ductmate Industries
guarantees Easyrod/Easystud against
defective material.
Installation Instructions:
! Drill a hole for 9/32” through both top
and bottom walls of duct.
! Cut conduit to size of duct.
! Place Easyrod/Easystud insert on
installation tool with prongs facing the
tool.
! Drive one insert into each end of the
conduit.
! Position the conduit with inserts
protruding through holes in duct walls.
! Install the washer and nut to bolt and
tighten till snug. (Do not overtighten.)
Simplify Your Tie Rod Installation
D U C T M A T E
Industries, Inc.®
• Perfect for positive and negative pressure installations• Inserts available for 1/2" and 3/4" EMT conduit• Consistent tie rod length insures proper installation
LODI, CA810 S. Cluff AvenueLodi, CA 95240-3141800-344-3270209-333-4680FAX: 209-333-4678
®
Distributed By:
D E S C R I P T I O N
B A S I C U S E
I N S T A L L A T I O N I N S T R U C T I O N S
P A C K A G I N G I N F O R M A T I O N
Easyrod is an extremely strong and quick alternative method for theinstallation of tie rod reinforcements into ductwork. Threadedinserts are applied to the inside of EMT conduit to insure fast andconsistent installation of internal reinforcements.
Drill clearance hole for 1/4" bolt (9/32" typ.) through top andbottom of duct panels at desired location. Cut 1/2" or 3/4" EMTconduit to duct size. Apply Easyrod insert onto installation tool,prongs toward installation tool. Drive an Easyrod insert into eachend of conduit. Place conduit through open end of duct to drilledhole location. Fasten bolt through galvanized neoprene washer andthrough drilled hole into Easyrod insert. Tighten both ends untilsnug (Do not overtighten). Result: a leak free installation requiring no extra sealing.
The Easyrod set consists of one of each of the following components:
1/2" or 3/4" Easyrod insert1/4" I.D. x 1" O.D. galvanized neoprene bonded washer1/4" x 1" N.C., Gr. 5, plated hex bolt
An Easyrod tool is also available to simplify and reduce assemblytime.
S P E C I A L C H A R A C T E R I S T I CPull out rated -900 lbs.
Easyrod can be used wherever internal tie rods are needed withinthe duct system.
P R O D U C T G U A R A N T E E
Easyrod is guaranteed against defective material.
BoltPipe insert is friction fittedwith internal threads
Stamped, galvanized discwith neoprene washersecures the ductwall.
Light Wall conduit Duct wall
D E S C R I P T I O N
B A S I C U S E
I N S T A L L A T I O N I N S T R U C T I O N S
P A C K A G I N G I N F O R M A T I O N
Easystud is a faster alternative method for the installation of tie rodreinforcements into ductwork. Threaded stud inserts are applied tothe inside of EMT conduit to insure fast and consistent installation ofinternal reinforcements.
Drill a clearance hole for 1/4" bolt (9/32" typ.) bolt through boththe top and bottom of the duct panels at the desired location for thereinforcement. Cut a length of 1/2" EMT conduit to the size of theductwork. Apply an Easystud insert onto the installation tool, withthe prongs facing the tool. Drive an Easystud insert into each end ofthe conduit. Position the conduit in the ductwork with the twoEasystud inserts protruding through the predrilled holes in the duct.Apply the washer and bolt to both ends of the Easystud inserts.Tighten both ends until snug (Do not over tighten) Result: a leak free installation requiring no extra sealing.
The Easystud set consists of one of each of the following components: