Fieldpiece Static Pressure Probes Model: ASP2 OPERATOR’S MANUAL Description Use your ASP2 Static Pressure Probes to meas- ure duct static pressure the right way. Slide your ASP2 into the rubber hose of Fieldpiece models AMN2, ADMN2, SDMN5, or any manometer with appropriate sized ports, to greatly improve accura- cy over using the hose alone. Designed for HVAC/R techs, the magnetic flange and painted arrow ensure proper orientation and allow hands free use. How to use 1. Slide the rubber hose coming from the pressure port of your manometer into the bottom (barbed end) of the ASP2. 2. Zero your manometer to ambient pressure. 3. Drill a 1/4” (0.7cm) hole in the duct to insert the ASP2. (Avoid insertion near bends/elbows in duct work.) 5. Insert the ASP2 and use the arrow on the base to align the arm so it points directly into the air stream. Place the magnetic base of the probe flush with the side of the duct to ensure the probe is pointing parallel to the air stream. 6. Read static pressure from manometer. 7. Remove probe and plug any holes. Two ASP2s in use with a Fieldpiece SDMN5 to measure static pressure across a blower. Arrows show direction of air flow. Warning Sealing holes is essential to maintaining the effectiveness of an HVAC/R system. Leaving open holes in flues or other exhaust ventilation decreases preformance and could present hazardous situations to occu- pants. ! ! Caution Holes should not be made near vital parts of any HVAC/R System, such as evaporator coils, combustion chambers or heat exchangers. ! ! Fieldpiece Static Pressure Probes Model: ASP2 OPERATOR’S MANUAL Description Use your ASP2 Static Pressure Probes to meas- ure duct static pressure the right way. Slide your ASP2 into the rubber hose of Fieldpiece models AMN2, ADMN2, SDMN5, or any manometer with appropriate sized ports, to greatly improve accura- cy over using the hose alone. Designed for HVAC/R techs, the magnetic flange and painted arrow ensure proper orientation and allow hands free use. How to use 1. Slide the rubber hose coming from the pressure port of your manometer into the bottom (barbed end) of the ASP2. 2. Zero your manometer to ambient pressure. 3. Drill a 1/4” (0.7cm) hole in the duct to insert the ASP2. (Avoid insertion near bends/elbows in duct work.) 5. Insert the ASP2 and use the arrow on the base to align the arm so it points directly into the air stream. Place the magnetic base of the probe flush with the side of the duct to ensure the probe is pointing parallel to the air stream. 6. Read static pressure from manometer. 7. Remove probe and plug any holes. Two ASP2s in use with a Fieldpiece SDMN5 to measure static pressure across a blower. Arrows show direction of air flow. Warning Sealing holes is essential to maintaining the effectiveness of an HVAC/R system. Leaving open holes in flues or other exhaust ventilation decreases preformance and could present hazardous situations to occu- pants. ! ! Caution Holes should not be made near vital parts of any HVAC/R System, such as evaporator coils, combustion chambers or heat exchangers. ! !
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
FieldpieceStatic Pressure ProbesModel: ASP2
OPERATOR’S MANUAL
DescriptionUse your ASP2 Static Pressure Probes to meas-
ure duct static pressure the right way. Slide yourASP2 into the rubber hose of Fieldpiece modelsAMN2, ADMN2, SDMN5, or any manometer withappropriate sized ports, to greatly improve accura-cy over using the hose alone. Designed for HVAC/Rtechs, the magnetic flange and painted arrowensure proper orientation and allow hands free use.
How to use1. Slide the rubber hose coming from the pressure
port of your manometer into the bottom (barbedend) of the ASP2.
2. Zero your manometer to ambient pressure.3. Drill a 1/4” (0.7cm) hole in the duct to insert the
ASP2. (Avoid insertion near bends/elbows induct work.)
5. Insert the ASP2 and use the arrow on the baseto align the arm so it points directly into the airstream. Place the magnetic base of the probeflush with the side of the duct to ensure theprobe is pointing parallel to the air stream.
6. Read static pressure from manometer.7. Remove probe and plug any holes.
Two ASP2s in use with a Fieldpiece SDMN5 tomeasure static pressure across a blower. Arrowsshow direction of air flow.
WarningSealing holes is essential to maintaining
the effectiveness of an HVAC/R system.Leaving open holes in flues or other exhaustventilation decreases preformance andcould present hazardous situations to occu-pants.
! !
CautionHoles should not be made near vital parts
of any HVAC/R System, such as evaporatorcoils, combustion chambers or heatexchangers.
! !PRESS FOR 1 SECOND
AUTO-OFF BATTERYCHECK
FieldpieceStatic Pressure ProbesModel: ASP2
OPERATOR’S MANUAL
DescriptionUse your ASP2 Static Pressure Probes to meas-
ure duct static pressure the right way. Slide yourASP2 into the rubber hose of Fieldpiece modelsAMN2, ADMN2, SDMN5, or any manometer withappropriate sized ports, to greatly improve accura-cy over using the hose alone. Designed for HVAC/Rtechs, the magnetic flange and painted arrowensure proper orientation and allow hands free use.
How to use1. Slide the rubber hose coming from the pressure
port of your manometer into the bottom (barbedend) of the ASP2.
2. Zero your manometer to ambient pressure.3. Drill a 1/4” (0.7cm) hole in the duct to insert the
ASP2. (Avoid insertion near bends/elbows induct work.)
5. Insert the ASP2 and use the arrow on the baseto align the arm so it points directly into the airstream. Place the magnetic base of the probeflush with the side of the duct to ensure theprobe is pointing parallel to the air stream.
6. Read static pressure from manometer.7. Remove probe and plug any holes.
Two ASP2s in use with a Fieldpiece SDMN5 tomeasure static pressure across a blower. Arrowsshow direction of air flow.
WarningSealing holes is essential to maintaining
the effectiveness of an HVAC/R system.Leaving open holes in flues or other exhaustventilation decreases preformance andcould present hazardous situations to occu-pants.
! !
CautionHoles should not be made near vital parts
of any HVAC/R System, such as evaporatorcoils, combustion chambers or heatexchangers.
! !PRESS FOR 1 SECOND
AUTO-OFF BATTERYCHECK
ServiceReturn any defective ASP2 to Fieldpiece for war-
ranty service along with proof of purchase. ContactFieldpiece for out of warranty repair charges.One year limited warranty
This accessory is warranted to the original pur-chaser against defects in material and workman-ship for a period of one year from the date of pur-chase. During the warranty period, Fieldpiece willreplace or repair the defective unit, subject to verifi-cation of the defect.
Any damage to the instrument from dirt, mechan-ical abuse, or overexposure to damaging chemi-cals, are not covered under this warranty. Also notcovered are defects resulting from abuse, neglect,accident, unauthorized repair, alteration, or unrea-sonable use.
Any implied warranties arising out of the sale of aFieldpiece Instrument, including but not limited toimplied warranties of merchantability and fitness fora particular purpose, are limited to the above.Fieldpiece shall not be liable for loss of use of theinstrument or other incidental or consequentialdamages, expenses, or economic loss, or for anyclaim or claims for such damage, expense, or eco-nomic loss.
Local laws vary. Above limitations or exclusionsmay not apply to you. This warranty gives you spe-cific legal rights, and you may also have other rightswhich vary by location.
Compatible instrumentsFieldpiece SDMN5
ADMN2 accessory head AMN2 accessory head
T2T2T2T2T2T2T2T2T2
T2T2T2T2T2T2T2T2T2T2
P1
P1P2 ZERO
HOLD UNIT
ON/OFF
P2
88.8888.88APO
88.8888.88inWC
mmWC
mbar
psiHOLD
PRESS FOR 1 SECOND
AUTO-OFF BATTERYCHECK
v07
OFF
2000
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
AMN2
ManometerAccessoryHead
ON
0.1
AUTO OFF
Converts 1” watercolumn to1mVDC or 10mVDC(selectable).
0.01(LCD/10)
LO BATT
Resolution ON
Zero Set
OFF
AMN2
ManometerAccessoryHead
ON
0.1
AUTO OFF
Converts 1” watercolumn to1mVDC or 10mVDC(selectable).
0.01(LCD/10)
LO BATT
Resolution ON
Zero Set
OFF
AMN2
ManometerAccessoryHead
ON
0.1
AUTO OFF
Converts 1” watercolumn to1mVDC or 10mVDC(selectable).
0.01(LCD/10)
LO BATT
Resolution ON
Zero Set
OFF
ServiceReturn any defective ASP2 to Fieldpiece for war-
ranty service along with proof of purchase. ContactFieldpiece for out of warranty repair charges.One year limited warranty
This accessory is warranted to the original pur-chaser against defects in material and workman-ship for a period of one year from the date of pur-chase. During the warranty period, Fieldpiece willreplace or repair the defective unit, subject to verifi-cation of the defect.
Any damage to the instrument from dirt, mechan-ical abuse, or overexposure to damaging chemi-cals, are not covered under this warranty. Also notcovered are defects resulting from abuse, neglect,accident, unauthorized repair, alteration, or unrea-sonable use.
Any implied warranties arising out of the sale of aFieldpiece Instrument, including but not limited toimplied warranties of merchantability and fitness fora particular purpose, are limited to the above.Fieldpiece shall not be liable for loss of use of theinstrument or other incidental or consequentialdamages, expenses, or economic loss, or for anyclaim or claims for such damage, expense, or eco-nomic loss.
Local laws vary. Above limitations or exclusionsmay not apply to you. This warranty gives you spe-cific legal rights, and you may also have other rightswhich vary by location.
Compatible instrumentsFieldpiece SDMN5
ADMN2 accessory head AMN2 accessory head
T2T2T2T2T2T2T2T2T2
T2T2T2T2T2T2T2T2T2T2
P1
P1P2 ZERO
HOLD UNIT
ON/OFF
P2
88.8888.88APO
88.8888.88inWC
mmWC
mbar
psiHOLD
PRESS FOR 1 SECOND
AUTO-OFF BATTERYCHECK
v07
OFF
2000
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
ADMN2
Dual-PortManometerAccessoryHead
P1P2
P1-P2
ON
0.1 ENGLISH
METRIC0.01
(LCD/10)
Lo Batt
Resolution
ZERO AUTO
OFF
P1 P2
AMN2
ManometerAccessoryHead
ON
0.1
AUTO OFF
Converts 1” watercolumn to1mVDC or 10mVDC(selectable).
0.01(LCD/10)
LO BATT
Resolution ON
Zero Set
OFF
AMN2
ManometerAccessoryHead
ON
0.1
AUTO OFF
Converts 1” watercolumn to1mVDC or 10mVDC(selectable).
0.01(LCD/10)
LO BATT
Resolution ON
Zero Set
OFF
AMN2
ManometerAccessoryHead
ON
0.1
AUTO OFF
Converts 1” watercolumn to1mVDC or 10mVDC(selectable).
0.01(LCD/10)
LO BATT
Resolution ON
Zero Set
OFF
Related Documents
