Wal-Mart Universal Monitor Stand
Installation Manual
CIM 2122 10/14/16
Walmart Universal Monitor Stand Conversion\Installation Instructions
1
Refer to the illustrated instructions below to convert the Universal Monitor Stands from Single
to Dual version, and Left Hand to Right Hand versions for both Mainline and Speedy check lanes
– before installing on the conveyor or cabinet.
Attachment hardware is included with each Universal Monitor Stand. Refer to the hardware
specifications on page #3.
The Universal Monitor Stand will be shipped as a Single Monitor Left Hand Version (as shown
below). To convert the Monitor Stand to a Dual or Right Hand (Mainline or Speedy) version,
follow the appropriate instructions designated for each configuration.
If you require assistance with the conversion or installation, please call the Pan Oston Field
Operations Department at 1-800-472-6678.
Walmart Universal Monitor Stand Conversion\Installation Instructions
2
Configuration Reference Page
Version Page
BM-132895-KIT Universal Accessory Kit 3
QR Code Information 4
Hardware Kit \ Tools Required 5
Convert Single Left Hand Stand to Single Right Hand Stand 6 - 14
Convert Single Monitor Stand to Dual Monitor Stand (Left \ Right Hand) 15 - 21
Installation of Monitor Stand to belted Check lanes 22 - 23
Installation of Monitor Stand to Speedy lanes 24 – 29
Installation of Monitors and EFT Card Reader 30 - 32
Walmart Universal Monitor Stand Conversion\Installation Instructions
3
BM-132895-KIT Article Number: 100590296
Walmart Universal Monitor Stand Conversion\Installation Instructions
4
QR CODE INFORMATION The checkout lanes and accessory kits have a QR code that may be read with a standard QR
codereader app on a cell phone. The purpose of the QR code is to provide a link to
documentation pertaining to the installation of the checkstands.
Walmart Universal Monitor Stand Conversion\Installation Instructions
5
Universal Monitor Stand Hardware Kit
The Hardware Kit is made up of machine screws and star washers designated for the
components that are to be removed or repositioned depending on the different configurations
(Single or Dual Monitor, Left Hand or Right Hand, Belted or Speedy Lanes) . Refer to the
installation instructions below in regard to the correct hardware required. A Square head drive
and Phillips head screwdriver will be needed to perform this installation.
Quantity of 2
¼-20 x 1 ¼
Machine Screw
Quantity of 8
¼-20 x ¾”
Machine Screw
Quantity of 8
M4 x 12mm
Machine Screw
Quantity of 10
1/4” Star Washer
Walmart Universal Monitor Stand Conversion\Installation Instructions
6
Universal Monitor Stand – Single Left Hand
Follow the steps below to convert the Single Left Hand version to the Single Right
Hand version.
Walmart Universal Monitor Stand Conversion\Installation Instructions
7
STEP 1: Remove the (7) ¼-20 machine screws\washers, from both sides and top, which attaches
the existing check shelf to the monitor base. Relocate the check shelf to the opposite
side of the monitor base to create a Right Hand version.
Check Shelf
Monitor Base
(7) Mounting Screws\Washers
Walmart Universal Monitor Stand Conversion\Installation Instructions
8
STEP 2: Mount the check shelf to the opposite side of the Monitor Base – using the same (7) ¼-20”
machine screws \ washers previously removed in STEP 1.
Walmart Universal Monitor Stand Conversion\Installation Instructions
9
STEP 3: When converting the Monitor Stand from a Left Hand version to a Right Hand version, the check shelf must be repositioned to have the overhang on the side opposite the EFT Pull Bracket (as shown by the arrows below). NOTE: The overhang position is standard regardless of orientation (Left Hand or Right Hand). Using a Phillips head screwdriver, remove the (2) mounting screws that attach the Policy Cover to the Check Shelf, then remove the Policy Cover.
Policy Cover mounting
screws
Walmart Universal Monitor Stand Conversion\Installation Instructions
10
STEP 4: Remove the (4) ¼-20 x 1” machine screws that attach the Check Shelf to the Monitor Base, then
reposition the Check Shelf where the overhang is opposite the EFT Pull Bracket – then reattach
with the same hardware as was removed.
Insert mounting screws
into the (4) holes shown
Walmart Universal Monitor Stand Conversion\Installation Instructions
11
STEP 5: Reposition the Monitor Extension Bracket to attach directly to the Monitor Base by first
removing the (4) ¼-20 x ½” mounting screws\washers (as shown below).
Walmart Universal Monitor Stand Conversion\Installation Instructions
12
STEP 6: Remove the (4) ¼-20 x ½” machine screws\washers that attach the Monitor Extension Bracket to
the Monitor Base.
Walmart Universal Monitor Stand Conversion\Installation Instructions
13
STEP 7: Reattach the Monitor Mount to the Monitor Base using the same (4) ¼-20 x ½” machine screws
\ washers previously removed.
Walmart Universal Monitor Stand Conversion\Installation Instructions
14
The Single Right Hand Monitor Stand will look like this upon completion of the conversion. Repeat the
above Steps in reverse order to convert back a Single Right Hand Monitor Stand.
Universal Monitor Stand – Single Right Hand Version
Walmart Universal Monitor Stand Conversion\Installation Instructions
15
Universal Monitor Stand – Single to Dual ( Left Hand Version)
Follow the steps below to convert the Universal Monitor Stand - Single Left Hand version to the
Dual Left Hand version. Refer to the Single Left to Single Right Hand instructions on pages (4
through 12) to reposition the Check shelf and Monitor plate (Cashiers side)
STEP 1: Reposition the Check Shelf to the extended position by first removing the (7) ¼-20 x ½” machine
screws \ washers (as shown below).
Walmart Universal Monitor Stand Conversion\Installation Instructions
16
STEP 2: Extend the Check Shelf outward and align the mounting holes with the open threaded rivet nuts
at the end of the Monitor Base. Attach the Check Shelf to the Monitor Base using the (7) ¼-20 x
½” machine screws previously removed.
Walmart Universal Monitor Stand Conversion\Installation Instructions
17
STEP 3: Remove the (4) # 8-32 x ½” machine screws that attach the EFT Pull Bracket to the EFT Riser
Bracket as shown – then remove the EFT Riser Bracket to access the additional (4) screws that
attach the EFT Pull Bracket to the Monitor Base.
Mounting Screws
Walmart Universal Monitor Stand Conversion\Installation Instructions
18
STEP 4: Remove the (4) #8-32 x ½” machine screws that attach the EFT Pull Bracket to the Monitor Stand
Base.
Mounting Screws
Walmart Universal Monitor Stand Conversion\Installation Instructions
19
STEP 5 : Align the (4) mounting holes on the Monitor\EFT Bracket, with the (4) threaded rivet nuts on
the Monitor Stand Base.
STEP 6: Attach the Dual Monitor plate to Monitor Stand Base using the (4) #8-32 x ½” machine screws
removed in STEP 4.
Rivet Nuts
Walmart Universal Monitor Stand Conversion\Installation Instructions
20
STEP 7: Attach the EFT Riser Bracket to the Monitor\EFT Bracket using (4) #8-32 x ½” machine screws
which are attached from behind (as shown below).
Attach EFT Riser Bracket from the back side
Walmart Universal Monitor Stand Conversion\Installation Instructions
21
STEP 8: The EFT ISD Adaptor Plate is NOT included as part of the Universal Monitor Stand or Hardware
Kit from Pan Oston. This plate and EFT mounting hardware is supplied by Walmart ISD
STEP 9: Attach the EFT Adaptor Plate to the EFT Riser Bracket using (4) #8-32 x ½” machine screws.
EFT Adaptor Plate
Mounting screw locations
Walmart Universal Monitor Stand Conversion\Installation Instructions
22
Mounting the Universal Monitor Stand Base to the Belted Conveyor
STEP 1: Place the Monitor Stand Base over the scanner end of the rail on the conveyor, aligning
the inner sets of both slots (refer to the RED arrows for proper alignment) – with the
3rd and 4th hole locations.
Scanner End
Walmart Universal Monitor Stand Conversion\Installation Instructions
23
STEP 2: Attach the Monitor Stand Base to the conveyor by using (2) ¼-20 x ¾” machine screws
on EACH side of the rail. From the scanner end of the conveyor, use the 3rd and 4th
hole locations - on each side – as stated in STEP 1 above.
Outer Mounting Screw Locations
Inner Mounting Screw Locations
Walmart Universal Monitor Stand Conversion\Installation Instructions
24
Mounting the Universal Monitor Stand Base to the Speedy Cabinet
STEP 1: Place the Monitor Stand Base over the scanner end of the rail on Speedy cabinet,
aligning both inner sets of slots (refer to the illustrations below for proper alignment) –
with the 1st and 2nd rivet nuts.
From the customer
side (Left) – align
2nd slot with 1st rivet
nut.
From the customer side
(Right) – align 2nd slot
with 3rd rivet nut
Walmart Universal Monitor Stand Conversion\Installation Instructions
25
STEP 2: Place the Rail Extension into the opening at the intake end of the Monitor Stand.
Ensure the end of the Rail Extension is flush with the end of the Monitor Stand. Attach
the Rail Extension to the Monitor Stand using (2) ¼”-20 x ¾” machine screws. (refer to
the illustrations below for proper alignment).
Rail Extension is to be flush
with Monitor Stand
Walmart Universal Monitor Stand Conversion\Installation Instructions
26
Mounting the Touch Screen Monitor on the Cashier Side (Single or Dual Monitor)
STEP 1: Place \ align the mounting holes on the backside of the monitor with the mounting
holes on the Monitor Stand plate and attach with (4) #8-32 x ½” machine screws.
Monitor mounting hole
locations
Walmart Universal Monitor Stand Conversion\Installation Instructions
27
Mounting the Touch Screen Monitor on the Customer Side (Dual Monitor Only)
STEP 1: Place \ align the mounting holes on the backside of the monitor with the mounting
holes on the Monitor Stand plate and attach with (4) #8-32 x ½” machine screws.
Monitor mounting hole
locations
Walmart Universal Monitor Stand Conversion\Installation Instructions
28
STEP 2: Route the cables for the monitors (Single and Dual) through the opening in Mount Extension
into the scanner well area.
Opening for Monitor
Cable Routing
Walmart Universal Monitor Stand Conversion\Installation Instructions
29
Mounting the EFT Card Reader on the Customer Side (Single or Dual Monitor)
Refer to the ISD EFT Plate instructions for EFT mounting
Mounting the LED Customer Display (Single Monitor Only)
STEP 1: Before mounting the LED Display to the Monitor Base Stand it will be necessary to
feed the cables through the routing holes as shown below.
Cable Routing Path
Walmart Universal Monitor Stand Conversion\Installation Instructions
30
STEP 2: Mount the LED Customer Display to the Monitor Stand Base by using (2) ¼-20 x 1 ¼”
machine screws
Cable Routing Path
Walmart Universal Monitor Stand Conversion\Installation Instructions
31
Completed Dual Monitor Stand Version
Customer Side
Cashier Side
Walmart Universal Monitor Stand Conversion\Installation Instructions
32
Completed Single Monitor Stand Version
Cashier Side
Customer Side