White Paper
Abstract
This white paper provides best practices for migrating data from an EMC® file-storage array (such as a Celerra® NS) to one of EMC’s new VNX™ series platforms. It includes simple step-by-step instructions on how to use Celerra Replicator™ and VNX Replicator to perform the migration. If you wish to migrate data from an EMC block-storage array (such as a CLARiiON® AX or CX™ array), refer to the white paper Migrating Data from an EMC CLARiiON Array to a VNX Platform Using SAN Copy. March 2011
MIGRATING DATA FROM AN EMC CELERRA ARRAY TO A VNX PLATFORM USING CELERRA REPLICATOR A “how-to” guide featuring best practices
2 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Copyright © 2011 EMC Corporation. All Rights Reserved. EMC believes the information in this publication is accurate of its publication date. The information is subject to change without notice. The information in this publication is provided “as is”. EMC Corporation makes no representations or warranties of any kind with respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a particular purpose. Use, copying, and distribution of any EMC software described in this publication requires an applicable software license. For the most up-to-date listing of EMC product names, see EMC Corporation Trademarks on EMC.com. All other trademarks used herein are the property of their respective owners. Part Number h8174.1
3 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Table of Contents
Executive summary.................................................................................................. 4
Introduction ............................................................................................................ 4
Audience ............................................................................................................................ 4
Terminology ....................................................................................................................... 5
Using Celerra Replicator and VNX Replicator to migrate data from a Celerra to a VNX series platform ........................................................................................................ 5
The step-by-step procedure ................................................................................................ 5
Step 1 Obtain and install a temporary Replicator license key .......................................... 6
Step 2 Create interfaces on the VNX platform ................................................................. 6
Step 3 Create interfaces for the Data Mover interconnects .............................................. 7
Step 4 Create a nasadmin user on VNX ........................................................................... 8
Step 5 Use the Replication Wizard to replicate the VDM ................................................. 9
Step 6 Replicate the file systems on the VDM that you wish to migrate to the VNX ........ 31
Step 7 Verify the last synchronization time ................................................................... 38
Step 8 Change the source file system to “Read Only” ................................................... 38
Step 9 Create a server interface on the VNX .................................................................. 40
Step 10 Using Unisphere on the Celerra, switch over the replicated VDMs .................... 40
Step 11 Using Unisphere on the Celerra, switch over the replicated file systems .......... 42
Step 12 Verify file systems are available ...................................................................... 43
Step 13 Clean up replication sessions .......................................................................... 44
Step 14 Back up file system data ................................................................................. 44
Considerations for copying NFS-accessed file systems ........................................... 44
Conclusion ............................................................................................................ 46
References ............................................................................................................ 46
4 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Executive summary EMC’s new VNX™ series of midrange storage platforms features major new architectural innovations such as unified Fully Automated Storage Tiering (FAST), unified replication, unified management, and the new SAS back end. The point-to-point architecture of the SAS back end offers higher availability and better performance than older architectures such as Fibre Channel.
This white paper serves as a migration guide to help you move data from an EMC® midrange file-storage array (such as a Celerra® NS model) to a new VNX series storage platform. The paper provides simple step-by-step best practices that show you how to use Celerra Replicator™ (V2) software to perform a low/no-cost migration of data to your new VNX platform, so that you can start taking advantage of the new VNX technology as quickly as possible.
If you need to migrate data from one of EMC’s block-storage arrays (such as a CLARiiON® AX or CX™ model) refer to Migrating Data from an EMC CLARiiON Array to a VNX Platform Using SAN Copy.
Introduction To help ensure a smooth transition for customers who wish to migrate their data from older EMC midrange arrays to the powerful new VNX series platform, EMC supports a wide range of data migration tools and techniques. EMC recently performed numerous tests to pinpoint the most efficient way to use these tools to migrate data to a new VNX array. After careful testing, EMC concluded that the most effective way to migrate data from a block-based array (such as a CLARiiON AX or CX model) is to utilize EMC SAN Copy™, which is described in Migrating Data from an EMC CLARiiON Array to a VNX Platform Using SAN Copy.
On the other hand, our tests showed that when migrating from a file-based array (such as a Celerra NS model), the most effective tool is Celerra Replicator. The rest of this white paper provides a step-by-step procedure, including best practices, to help you make a smooth transition to your new VNX platform using Celerra Replicator and VNX Replicator. This procedure will cover the specific use case of migrating CIFS shares on Virtual Data Movers (VDMs). There are variations on the procedure if you are not using VDMs or if you are using NFS. NFS considerations are covered briefly at the end of the document.
Audience
This white paper is for customers who have purchased, or are considering purchasing, an EMC VNX series platform and wish to migrate their data from a previous generation EMC file-storage array to the new VNX series hardware. The paper also serves as a guide for EMC field services and customer service employees. Familiarity with Celerra Replicator is highly recommended.
5 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Terminology Celerra Replicator: Celerra Replicator is licensed software that resides on the
Celerra array; you use this software to replicate file systems from one storage platform to another. Traditionally this software is chargeable; however, EMC provides this license free of charge for 180 days to customers who wish to migrate their data from a Celerra to a VNX platform.
Please note that you need be running Celerra Replicator (V2) and not the older version (V1) to perform the migration described in this paper.
Virtual Data Movers (VDM): A VDM is a software feature on the Celerra that allows an administrator to separate CIFS servers, replicate their CIFS environment, and move servers from Data Mover to Data Mover.
VNX Replicator: VNX Replicator is licensed software that resides on the VNX series platform. This software requires a license before you can enable it via Unisphere™. There is a free 180-day license available for users who wish to migrate file systems from a Celerra to the new VNX platform.
Using Celerra Replicator and VNX Replicator to migrate data from a Celerra to a VNX series platform This procedure shows you how to migrate Common Internet File System (CIFS) files in VDMs from a Celerra array to a VNX platform. Please note that this data migration procedure is for customers who wish to migrate from a Celerra who:
Are running DART operating system release 6.0 or later
Are running CIFS and have Virtual Data Movers enabled
Have less than 20 TB of data
Have 20 or fewer attached hosts
Are in the same domain and network as the target VNX to which you plan to migrate the data
If your Celerra does not meet these requirements, we strongly encourage you to engage Professional Services from EMC, or an EMC partner, to execute your data migration from your Celerra to a VNX.
The step-by-step procedure
As would be the case with any migration procedure, we highly recommend performing a full file system backup before undertaking any of the following steps.
6 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 1 Obtain and install a temporary Replicator license key
On your Celerra and VNX platform, click the Settings tab, and click Manage Licenses for File. Enable Replicator and SnapSure™, as shown in Figure 1. Log out of the GUI and log back in.
Figure 1. Enabling necessary licenses
Step 2 Create interfaces on the VNX platform
Next, you must configure interfaces on the VNX platform that will be used to present the file systems to the Windows servers that will be migrated onto the VNX. To configure the interfaces using the command line on the VNX Control Station type in this command:
server_ifconfig server_2 -create -Device <device> -name
<name> -protocol IP <interface IP> <subnet mask>
<broadcast>
7 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Or, you can configure the interfaces in the VNX Unisphere GUI. To do this, select Settings > Network > Settings for File, click the Interfaces tab, and click Create at the bottom of the window that opens.
Step 3 Create interfaces for the Data Mover interconnects
Create interfaces on both the Celerra and the VNX. Replicator will use these interfaces for the DM-to-DM interconnects (paths) during replication.
To do this using the command line on the Celerra Control Station, type in this command:
server_ifconfig server_2 -create -Device <device> -name
<name> -protocol IP <interface IP> <subnet mask> <broadcast>
Or, you can do this in the Celerra Unisphere GUI by going to the System tab and clicking Create Network Interfaces on the left-hand panel.
8 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 4 Create a nasadmin user on VNX
In the initial VNX release you must add a global user, called nasadmin, to match the username that is being used on the Celerra array. You must do this in the VNX Unisphere window. Select Settings > Security > User Management and click Global User Management. Add a nasadmin global user with a password of nasadmin as shown in Figure 2, and assign the nasadmin global user with a NAS administrative storage domain role.
Figure 2. Adding a nasadmin user to the VNX platform
9 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 5 Use the Replication Wizard to replicate the VDM
Configure a replication session using the Replication Wizard in Unisphere on the Celerra. On the Celerra, click the Replicas tab and click Replication Wizard on the left-hand panel. In this example (shown in Figure 3) we select Virtual Data Mover (VDM).
Figure 3. Select a Replication Type
10 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
The wizard asks you to specify the destination VNX platform. If your destination VNX platform is present on the list, you may select it. If the VNX is a brand new array in your environment, then you may need to add it by clicking the New Destination Celerra button as shown in Figure 4.
Figure 4. Selecting or adding the destination VNX platform
11 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
The wizard will ask you to create the Celerra Network Server. First, give your destination VNX platform a name in the Celerra Network Server Name field. Then, specify the destination VNX platform’s Control Station IP address, and create a passphrase that you will remember as shown in Figure 5.
Figure 5. Create Celerra Network Server
12 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Next the wizard will ask you to specify the destination credentials, as illustrated in Figure 6. Type the IP address of the destination VNX array, and then type the login and password credentials for this array that you created in step 4. Click Next.
Figure 6. Specifying the destination VNX credentials
13 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Next the wizard steps you through creating the peer Celerra Network Server. Type a name for your source Celerra array, and then type the source Celerra’s IP address as shown in Figure 7. Then click Next.
Figure 7. Create Peer Celerra Network Server
14 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Review the selections that you have made, and then click Submit as shown in Figure 8.
Figure 8. Reviewing selections
15 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
The network servers should be created successfully, as shown in Figure 9. Click Next to continue.
Figure 9. Network servers successfully created
16 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Now that you have successfully created your destination Celerra Network Server (the destination VNX platform entry), select it from the list, as shown in Figure 10.
Figure 10. Selecting your destination VNX platform
17 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Next the wizard asks you to enter the Data Mover interconnect. You will probably have to click New Interconnect, as shown in Figure 11, to create a new Data Mover interconnect.
Figure 11. Creating new Data Mover interconnects
18 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Specify a name for the Data Mover interconnect. Choose the desired Data Mover, select the Show Advanced Settings checkbox, select the desired IP address (or addresses) for the interface to use, and click Next as shown in Figure 12.
Figure 12. Source interconnect settings
19 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Specify the IP address, login, and password credentials for the target VNX platform. Use the nasadmin user account and credentials that you created in step 4, and click Next. This is shown in Figure 13.
Figure 13. Specify Destination Credentials
20 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Specify a name for the Data Mover interconnect that you are creating on the destination VNX platform. Choose the desired Data Mover, and select the Show Advanced Settings checkbox. Select the desired IP address(es) for the interconnect, as shown in Figure 14, then click Next.
Figure 14. Destination Settings
21 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
We will not modify any of the settings in the Interconnect Bandwidth Schedule window, so simply click Next as shown in Figure 15.
Figure 15. Interconnect Bandwidth Schedule
22 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Make sure the Overview/Results window shows the values you entered. Click Submit (as shown in Figure 16) to create your source and target interconnects.
Figure 16. Overview/Results
23 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
After creating the interconnects, click Next as shown in Figure 17.
Figure 17. Finishing creation of the new interconnects
24 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Return to setting up the replication session. Select the source Data Mover interconnect that you have just created from the list, and click Next as shown in Figure 18.
Figure 18. Select Data Mover Interconnect
25 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Select the desired source and destination interfaces from the drop-down lists, or just leave them set to Any to let the system decide. (This is shown in Figure 19.) It is a best practice to use the interfaces that you have just created in case you have other replication sessions in use on the system. Click Next.
Figure 19. Select Replication Session's Interface
26 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
In the Select Source window, type a replication session name and select the desired VDM to be replicated as shown in Figure 20. Click Next.
Figure 20. Select Source
27 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
In the Select Destination window, you may select an existing VDM if you have one available. If you do not have a VDM to use, select Create Using Storage Pool and specify the desired pool or select clarsas_archive to allow the wizard to create a target pool for you; then click Next as shown in Figure 21.
Figure 21. Select Destination
28 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Select an update policy. You may choose to accept all of the defaults shown in Figure 22. Click Next.
Figure 22. Update Policy
29 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Review your settings and click Finish, as shown in Figure 23.
Figure 23. Reviewing Overview/Results
30 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Close the window after the wizard finishes. Your session will appear under the Replicas > Replications tab, as shown in Figure 24.
Figure 24. Closing the wizard
31 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 6 Replicate the file systems on the VDM that you wish to migrate to the VNX
When file systems are on VDMs, both the VDM and the file system(s) need to be replicated. Now that you have replicated the VDM, you need to replicate any file systems on the VDM that you wish to migrate to the VNX. First, you must open the Replication Wizard again to help you migrate the desired file system(s).
Select a Replication Type by selecting File System, then click Next as shown in Figure 25.
Figure 25. Select a Replication Type (file system)
32 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Select Ongoing File System Replication and click Next as shown in Figure 26.
Figure 26. Selecting a file system
33 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Now you need to:
Specify your destination array: This will be the same target VNX platform you selected when running the replication wizard for the VDM (as shown in Figure 10 on page 16), then click Next.
Select Data Mover Interconnects: Since you created Data Mover interconnects the last time we ran this wizard for the VDMs, the available interconnect(s) will appear in a list. Select the desired interconnect (as shown in Figure 18 on page 24), and then click Next.
Select the replication session’s interface: Accept the defaults of Any (as shown in Figure 19 on page 25) if this is the only replication session you plan to have running. If you have multiple sessions running, then it may prove beneficial to select a specific interface for this replication session. Click Next.
Select Source: Give the file system replication session a name, select the desired file system you wish to replicate from the drop-down list (as shown in Figure 27), then click Next.
Figure 27. Selecting a source file system to replicate
34 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Select Create Destination File System and select a target storage pool or accept the clarsas_archive choice for your Storage Pool and Checkpoint Storage. Then select the VDM in which your file system resides from the VDM drop-down menu, as shown in Figure 28. Click Next.
Figure 28. Selecting the destination file system
35 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Accept the default 10-minute update policy as shown in Figure 29, unless you wish to change it. Click Next.
Figure 29. Update Policy
36 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Leave the checkbox Use Tape Transport? clear, and click Next as shown in Figure 30. (Migrating really large file systems that do not easily lend themselves to replication over the WAN is not covered in this procedure.)
Figure 30. The “Use Tape Transport?” checkbox should be clear in the Select Tape Transport window
37 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Review the choices you have made, and click Finish. When the wizard finishes creating the file system replication session, click Close to close this window as shown in Figure 31.
Figure 31. Closing the Replication Wizard for the file system
38 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 7 Verify the last synchronization time
Under the Replicas > Replications tab, highlight the session(s) you have created and click Properties to open the properties window; this window should show that last synchronization time is recent. If it is not recent, make sure that Update Policies is set to Time Out of Sync: 10 minutes or some other reasonable value, as shown in Figure 32. If the data has changed recently, the session should be keeping the replica synchronized every 10 minutes.
Figure 32. Verifying the last synchronization time
Step 8 Change the source file system to “Read Only”
Before you switch over the file system from the source Celerra to the destination VNX platform, you must change the source file system to Read Only mode. This step begins the brief period of data unavailability that ends when your file systems become fully synchronized and switched over to the VNX platform. You should not perform this step until you are ready to incur the brief outage associated with the switchover period.
39 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
We recommend that you quiesce or otherwise shut down any application that is writing to the source file system from your host. To be certain that nothing is still writing to your source file system, unmap the file system, and change the file system properties to Read Only as described below.
In Unisphere on the Celerra array, go to Storage > File Systems and click the Mounts sub-tab. Select the file system mount that you are going to migrate and click Properties at the bottom of the window to open the Properties window. In the Properties window, select Read Only and click OK as shown in Figure 33.
Figure 33. Selecting Read Only
40 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 9 Create a server interface on the VNX
Before failing over your data from the Celerra to the VNX platform, you need to create an interface on the VNX platform that has the same name as the interface that is being used for the source Celerra server. If you are not sure of the name of the interface you need to create, you can try executing the switchover in step 10; the wizard will tell you the name of the interface that needs to be created if it does not already exist.
Bring up Unisphere on the VNX platform, select Settings > Settings for File, and from the interfaces tab, click Create. Create an interface and specify the same name as the name of your interface used for the source Celerra server.
Step 10 Using Unisphere on the Celerra, switch over the replicated VDMs
In Unisphere, select Replicas > Replications, select the VDM session(s) you want to switch over, and (with the session still highlighted) click Switchover, as shown in Figure 34. You will be asked to confirm the switchover. Click OK to confirm.
Figure 34. Initiating switchover
41 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
The status of the session will change to Switched Over, as shown in Figure 35.
Figure 35. Status changes to “Switched Over”
42 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 11 Using Unisphere on the Celerra, switch over the replicated file systems
Once you have switched over the VDMs, you need to switch over the file system sessions. Select the desired file system replication session(s) you wish to switch over, and click Switchover, as shown in Figure 36. Click OK to confirm the switchover.
Figure 36. Selecting the file system replication session to switch over
43 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
The file systems should change to Switched Over as shown in Figure 37.
Figure 37. System is shown as “Switched Over”
Step 12 Verify file systems are available
After the failover, if the DNS and NTP settings are configured properly, the file systems will still be accessible via the same host/share name. Although the underlying IP address has changed, it is transparent to any host that has the share mapped using its hostname. Alternatively, you may choose to remap your shares using the interface IP address created on the VNX platform. Ensure the file systems are mapped and accessible.
44 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Step 13 Clean up replication sessions
After the migration is complete, delete the replication sessions from the Celerra and VNX platforms. This can be done under the Replicas tab in the Unisphere GUI on the source Celerra array, as shown in Figure 38.
Figure 38. Deleting replication sessions
Step 14 Back up file system data
On the VNX platform, this is a good time to make a full backup of the data in case the data becomes unavailable at a later time.
Considerations for copying NFS-accessed file systems File systems that are accessed by NFS may already be mounted in the VDM being copied by the methods given previously, and so those file systems will already be copied. Or they could be mounted separately within the Data Mover, in which case they need to be copied by a file-only replication session.
45 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Various elements of the source NFS environment need to be reproduced on the target Data Mover, so that the NFS environment can be re-created. Since these NFS configuration pieces are not copied by the Replicator tool, they must be copied manually. The following items can be completed in the preparation stages of the migration:
The DNS configuration for UNIX domains, if separate from the Windows DNS used for Replicator
The NIS configuration, if it is configured on the source
The /.etc/passwd and /.etc/group files from the source Data Mover
Any Data Mover parameters that affect NFS or mixed usage of file systems, if they are non-default values on the source Data Mover. These might not only be nfs-facility parameters but also may include such cifs-facility parameters as acl.extacl (for mixed backup), acl.extendExtraGid, or acl.unixCheckAcl.
The /.etc/hosts and /.etc/netgroup files, if they were used on the source. These must be copied into files of a different name; otherwise you may get two hosts of the same name on different IP addresses.
When the file systems have been copied, you can switch over to the target system. In order for the NFS clients to mount files from the target Data Mover, you will need to:
Restore the names of /.etc/hosts and (if used) /.etc/netgroup on the target, and rename them on the source, so that the target takes the hostname
Re-create the NFS exports, as they were originally on the source. A script can be prepared for this earlier, using information gathered from a “server_export <movername> -l” console command on the source Data Mover
If there are clients that use NFS mounts by IP address instead of hostname, they will have to be addressed either individually, or if “automount” is used, by adjusting the automount tables.
46 Migrating Data from an EMC Celerra Array to a VNX Platform Using Celerra Replicator
Conclusion EMC recommends using EMC Celerra Replicator as the preferred tool for data from an EMC file-storage array (such as a Celerra NS) to one of EMC’s new VNX series platforms. This white paper provides simple step-by-step instructions on how to use Celerra Replicator and VNX Replicator to perform the migration. If you wish to migrate data from an EMC block-storage array (such as a CLARiiON AX or CX array), please refer to the white paper Migrating Data from an EMC CLARiiON Array to a VNX Platform Using SAN Copy.
References The following are available on Powerlink. Access required:
Migrating Data from an EMC CLARiiON Array to a VNX Platform Using SAN Copy
Using Celerra Replicator V2