KPT Preform & Closure tipper
KPTD Double tipper Two boxes for efficient loading
KPTD-2214 Double tipper
Efficient loading by means of a double tipper
The Tanner double tipper makes loading more efficient. The
double tipper enables two or even three preform boxes
(depending on the size of the boxes) to be tipped into the
preform feed silo at the same time. On the next page, you can use
the calculation table to work out how much time you are able to
save by using a double tipper in your production.
Facts
▪ Connection to the side of the Tanner silo belt SBT-32
or on any side of the Tanner silo belt SBT-33
▪ Maximum container size (W x D x H):
2 x 1300 x 1300 x 850-1300 mm
▪ Load: max. 900 kg
▪ Tipping height: 4.2 m
▪ Electrical tipper cover
▪ Remote control for releasing the tip
▪ Wheel stop and impact protection for the light barriers
Your time savings with the Tanner double tipper
Number of tipper loads per hour
Preform
Output
0.1 – 0.5 litres
(21,000 units/load)
0.6 - 1.0 litres
(13,600 units/load)
1.1 - 1.5 litres
(11,600 units/load)
1.6 - 2.0 litres
(11,000 units/load)
10,000 p/h 0.5 0.7 0.9 0.9
20,000 p/h 1 1.5 1.7 1.8
30,000 p/h 1.4 2.2 2.6 2.7
40,000 p/h 1.9 2.9 3.5 3.6
50,000 p/h 2.4 3.7 4.3 4.5
60,000 p/h 2.9 4.4 5.2 5.5
70,000 p/h 3.3 5.1 6 6.4
80,000 p/h 3.8 5.9 6.9 7.3
KPT Standard tipper
Tanner tippers in use worldwide
KPT-2014 Standard tipper
▪ Connection possible to any side of the silo rucksack (SRT) or
any silo belt (SBT).
▪ Maximum container size (W x D x H):
1300 x 1300 x 850-1420 mm
▪ Load: max. 400 kg
▪ Tipping height: 4 m
400 120
60
60
25
250
KPT Preform & Closure tipper
KPT-4014 for wider boxes
▪ Connection possible to any side of the silo rucksack
(SRT) or any silo belt (SBT).
▪ Max. container size (W x D x H):
1500 x 1300 x 850-1420 mm
▪ Load: max. 540 kg
▪ Tipping height: 4 m
KPT-5014 for automatic loading
▪ Equipped with lifting fork for automatic loading by a transport
system.
▪ Connection possible to any side of the silo rucksack (SRT) or any
silo belt (SBT).
▪ Max. container size (W x D x H): 1300 x 1300 x 850-1420 mm
▪ Load: max. 400 kg
▪ Tipping height: 4 m
KPT-6013 tipper for low ceilings
▪ Connection possible to any side of the silo rucksack (SRT)
or any silo belt (SBT).
▪ Max. container size (W x D x H):
1300 x 1300 x 850-1420 mm
▪ Load: max. 400 kg
▪ Tipping height: 3.7 metres
LX Cap Solution – the logistics concept for closures
Tipper and silo – one system
Tipper and silo – the result of two components is
an entirely logistics concept for the closure
handling, Tanner provides with the Cap Solution a
tipping device for the customer and the market,
which can be adjusted up to customer request.
Overview
▪ Cap Solution connection in-line to cap silo (CST)
possible
▪ Max. container size (WxDxH):
1300x1300x850-1420mm
▪ Load: max. 400kg
▪ Loading height: 4m
▪ Capacity cap silo: 1‘300 Liter
Options
▪ Electrical silo cover
▪ Transport system for complete automatione process
(Picture marked green)
"Hygienic design" options
Hygienic design options
The following hygienic design options apply
to all listed KPT preform tippers from
Tanner.
Base plate option
▪ Base plate for dirt separation (pictured right)
Stainless steel options
▪ Components in contact with the ground made from
stainless steel (pictured bottom right)
▪ Internal components covered with stainless steel sheets
(pictured below)
▪ Tipping container made completely from stainless steel
▪ Electrical enclosure made from stainless steel
▪ Tipper made completely from stainless steel
TANNER preform feeding systems for PET stretch blow machines or PET
preform test systems.
1985: 500 preforms/hour – 2011: 80,000 preforms/hour
More than 30 years ago, Tanner designed and manufactured PET preform
feeding systems for PET blow moulding machines. The first systems were
developed for an output of 500 preforms per hour. Since 2012, the Tanner VZT-
6172 preform feeding system has been able to feed over 80,000 preforms per
hour to the PET stretch blow machine.
30 years' experience, over 3’000 systems in use
Since the 1st Tanner preform feeding system was delivered in 1985, more than
3’000 systems in every output class have been brought into service worldwide.
In addition, preform tippers and components for UVC irradiation and preform
cleaning have also been included in the product range.
Tanner systems for preform test systems
As well as being suppliers to the PET bottle manufacturing market, Tanner also
supplies feeding systems for PET preform test systems. Whether offline (with a
Tanner tipper) or inline, directly from the preform injection moulding machine,
Tanner supplies the relevant concept that is tailored to the customer's
requirements. From October 2011, IMD Vista (www.imdvista.ch) is the official
partner of Tanner in the field of camera preform testing.
The challenge of preform handling and cleaning
Thanks to many years of experience, Tanner has succeeded in meeting the ever
greater challenges it faces (with regard to output, efficiency, changes to the
preform, climatic conditions, preform cleaning and inspection). In the field of
preform cleaning and inspection, the clamping conveyor is unique worldwide.
M. Tanner AG Länggstrasse 19 8308 Illnau Switzerland Telephone +41 (0)52 355 21 55 Fax +41 (0) 52 355 21 56 E-mail [email protected] Web www.mtannerag.ch Sales Telephone +41 (0)52 355 21 55 E-mail [email protected]
www.mtannerag.ch