COMPOSITION

Tipo

Material Fabric with polyurethane (TPU)impregnation

Finish Fabric

Colour Green

Coefficientof friction 0,3

Material Polyamide (PA)

0.06Total thickness 1.40

Weight 1.50 0.31 lbs./sq.ft

in.

kg/m2

mm

TECHNICAL SPECIFICATIONS

Humidity influence

Permanent antistatic dynamically(UNI EN ISO 21179)

NOTES

Issue: 10-10-2011 Last Update: 8-07-2021

5.0 29

Tensile strength 200 1142

min. -20 -4max 100 212

Temperatureresistance (2)

lbs./in.

lbs./in.

N/mm

N/mm

°C

°C °F(2) Use of the belt with limit values may reduce its life

25 1.0Minimum pulley diameter (1)

(1) The above mentioned values depend on running speed

mm in.

°F

To

p s

urf

ace

Tra

ctio

nco

reB

ott

om

su

rface

Both sides can be used for power transmission

yes

yes

no

FEATURES

Pull for 1% elongation

FLAT TRANSMISSION BELTS

CG217CODE TYPE

TECHNICAL DATA SHEET

Material Synthetic elastomer

Finish Fabric

Colour Green

Suitable for small power transmission

Can be also used as conveyor belts

Coefficientof friction

0,6

- Flexibility

- Resistance to overloads

- Coefficient of friction stable in time

SUITABLE FOR

Paper industry

Printing and graphic

Wood industry

Packaging

DISCLAIMERThe information contained in this document describes the features of the CHIORINO product as tested in a laboratory environment at a temperature of +23degrees °C at 50% relative humidity. It does not necessarily reflect the conditions of industrial use and it does not guarantee the product to be suitable for certainapplications. The client remains liable for the proper selection and correct use of the CHIORINO product. CHIORINO cannot be held responsible shoulddamages arise from the use of its products. Necessary alterations to this data can be made without prior notice.

CHIORINO S.p.A. - VIA S. AGATA, 9 - 13900 BIELLA - ITALIA - P.O.B. 460 - TEL. +39-015-8489.1 - FAX [email protected] - www.chiorino.com

COMPLIANCES

P1

REACH EC 1907/2006 Regulation and Amendments

Apply the K cement on the polyamide part of the splices.Let dry for 5 minutes, then match the belt ends, paying attention to align properly.Press according to the instructions shown.To ensure best joint life it is advisable not to run or tension the belt for 24 hours.

SKIVED JOINT ‘1’• Recommended joining procedure

• Skiving instructions

• Guide to the use of adhesives

• Layout of components

• Notes

Beltthickness

mm

Length

mm

Straight/diagonal

cut

Cam/wedgenumber

21-07-2011Issue: 30-01-2014Last Update:

Check our general catalogueto get further info onCHIORINO joining methods.

1.4 45 Diagonal 1.25-10 37 0 19,05 ---- 2 18,95 ----

T

mm

B

mm

Thicknessadjustment

End stopswitch ofworking

plate

T

mm

B

mm

Thicknessadjustment

End stopswitch ofworking

plate

Pulley Top coverSkiver

1.4 45 Diagonal 1.25-10 39 1 12-09 ---- 39 2.5 12-06 ----

B600 A

B300 SA

110 °C

110 °C

10

30

Press settings

Lower platentemperature

Curing timein press

Driving torque

Upper platentemperature

Cooling time:it is recommended to remove thebelt from the press once atemperature of 60/70 degrees Cis reached.

FLAT TRANSMISSION BELTS

TYPE

JOINING DATA SHEET

P1CG217CODE

Silicone sheeting thickness 3 mmBelt

Glossy non-adhesive fabric (ML58)

Upper heated platen

Lower heated platen

min.

CHIORINO S.p.A. - VIA S. AGATA, 9 - 13900 BIELLA - ITALIA - P.O.B. 460 - TEL. +39-015-8489.1 - FAX [email protected] - www.chiorino.com

Upper synthetic plate

Lower synthetic plate

DISCLAIMERThe information contained in this document describes the features of the CHIORINO product as tested in a laboratory environment at a temperature of +23degrees °C at 50% relative humidity. It does not necessarily reflect the conditions of industrial use and it does not guarantee the product to be suitable forcertain applications. The client remains liable for the proper selection and correct use of the CHIORINO product. CHIORINO cannot be held responsible shoulddamages arise from the use of its products. Necessary alterations to this data can be made without prior notice.

37

N/m