Uponor Control System,WiredInstallation Manual, UK, IRL
9416
-121
-00
/ IO
M-
V_0
7-02
Rober t Huber in t ie 3bP.O. Box 37FI-01511 VANTAA
+358 (0)20 129 211+358 (0)20 129 2841
I n k e e p i n g w i t h o u r p o l i c y o f c o n t i n u o u s i m p r o v e m e n t a n d d e v e l o p m e n t , U p o n o r r e s e r v e s t h e r i g h t t o c h a n g e s p e c i f i c a t i o n s w i t h o u t p r i o r n o t i c e .
Area managementUponor Hispania S .A.U.Cal le C , n° 24Pol ígono Industr ia l n°1E-28938 Mósto les (Madr id)
+34 91 685 3600+34 91 647 3245www.uponor.es
PO Box 101SE-730 61 Vi rsbo
+46 223 380 00+46 223 381 01
PO Box 1641 ( Industr iest rasse 56)D-97433 Hassfur t
+49 (0)9521 690 0+49 (0)9521 690 150www.uponor.de
Snapethorpe HouseRugby RoadLutterwor thLeicestersh i reLE17 4HN
+44 (0)1455 550355+44 (0)1455 550366www.uponorhous ingsolut ions .co.ukhsenqui r [email protected]
Uponor Control System - Installation Manual 3
Table of contents1. General recommendations ................................................................................................................................ 4
2. The Uponor Control System .............................................................................................................................. 5
2.1 Example of a system...................................................................................................................................... 5
2.2 Uponor Control System components................................................................................................................. 5
3. Installation....................................................................................................................................................... 6
3.1 Preparation before installation......................................................................................................................... 6
3.2 Installation of the components ........................................................................................................................ 6
3.3 Connections.................................................................................................................................................. 7
3.3.1 Controller description ....................................................................................................................... 7
3.3.2 Connect the actuators to the controller ............................................................................................... 7
3.3.3 Controller wiring .............................................................................................................................. 8
3.3.4 Installation of the options................................................................................................................ 11
3.3.5 Connecting the controller to the mains.............................................................................................. 12
3.4 Thermostats ............................................................................................................................................... 13
3.4.1 Opening the thermostats................................................................................................................. 13
3.4.2 Mounting and wiring the thermostats................................................................................................ 13
3.4.3 Thermostat setup........................................................................................................................... 14
3.5 Thermostat option ....................................................................................................................................... 14
3.5.1 Introduction .................................................................................................................................. 14
3.5.2 Wiring and setting the floor sensor potentiometer............................................................................... 14
4. Finishing the installation ................................................................................................................................ 15
5. System maintenance ...................................................................................................................................... 15
5.1 Controller current limitation .......................................................................................................................... 15
5.2 Actuator's behavior...................................................................................................................................... 15
5.3 Fallback mode............................................................................................................................................. 15
5.4 Automatic exercise function .......................................................................................................................... 15
5.5 Resetting Installation ................................................................................................................................... 15
6. Troubleshooting ............................................................................................................................................. 16
7. Installation report ...................................................................................................................................fold-out
8. Technical data .........................................................................................................................................fold-out
9. Wiring diagram / Controller description ..................................................................................................fold-out
4 Underfloor Heating
1. General recommendations
Safety measures
• Read and follow instructions.
• Installation must be performed by a qualified person according to local regulations.
• It is prohibited to make changes or modifications not specified in this manual.
• Power must be switched off when carrying out the wiring.
• We decline any responsibility concerning damages and breakdowns that may result from the non-observance of these instructions.
Symbols used in this manual
Power supply
Technical constraintsWARNINGRisk of bodily injuries or squeezing.Non observance may harm health or cause damage to product components.
STOP
CAUTIONImportant note on functionality. Non observance of this note may cause malfunctions.
InformationImportant operating advice and information.
See another document.
99See another page in the manual.
Heating/cooling.
Timer.
WARNING
• The Uponor Control System uses a 230VAC 50Hz power supply.
• In case of emergency, immediately disconnect the plug from the 230V mains.
• Do not use water to clean the Uponor Control System.
• Do not expose the Uponor Control System to flammable vapors or gases.
• Keep installation/data cables away from power cables > 50V to avoid interference.
• The electrical circuits of the boiler and the pump must be protected by a maximum 6A circuit-breaker.
Uponor Control System - Installation Manual 5
2. The Uponor Control SystemThe Uponor Control System is a complete management for underfloor heating systems. Comfort, user-friendliness and temperature control for each individual room of your home can be combined through the use of thermostats or floor temperature sensors.
2.1 Example of a systemThe Uponor Control System consists of thermostats, a controller and actuators. The controller manages the operation of the actuator when the thermostats detect a demand for heating or cooling. The Uponor Control System may be controlled with the help of three types of thermostats. Designed for maximum comfort, the thermostats communicate with the controller by non polarized two wired system. Don't "U-link" the outputs! It's automatic. One thermostat controls the following AC output if no thermostat is connected there, and so on. It's possible to use all kinds of Uponor Control System wired thermostats in
the same system.
2.2 Uponor Control System components
For an optimal setting of the system see Operation Manual.
Mark Description
Thermostat T-35
Thermostat Public T-33 (with the option of adding a floor sensor option)
Thermostat T-37 (with the option of adding a floor sensor option)
Controller, 6-channel (C-33) or 12-channel (C-35)
The floor sensor can be used for maximum or minimum limitation of the floor temperature, regardless of the room temperature. It can only be used with the Thermostat Public T-33 and Thermostat T-37.For example, the maximum limitation can protect a sensitive floor covering from exposure to too high temperature when there is a high heat demand. The minimum limitation can keep a tiled floor warm even when there is a no general demand for heat supply to the room.
1
2
3
4
Uponor designation Item Description
UponorController 6 or 12-channel controller
Fastening screws
Installation and Operation Manual
UponorThermostat T-35
Fastening screws
Thermostat
UponorThermostat T-37
Fastening screws
Thermostat for floor sensor
UponorThermostat T-33
Fastening screws
Thermostat Public
UponorFloor sensor
Floor sensor for Thermostat Public T-33 and Thermostat T-37 (option)
Uponor
RelayHeating / cooling relay (option)
Uponor
TimerTimer (option)
1
2
3
2
4
2
5
2
6
7
8
9
6 Underfloor Heating
3. InstallationInstallation steps
Uponor recommends that you follow the steps described below to guarantee the best possible installation:
3.1 Preparation before installationBefore beginning the installation:
• Verify the contents of the package with the list shown in Section 2 to make sure you have all the necessary products;
• Check whether a floor sensor has been mounted;
• Study the wiring diagram in the fold-out or inside the controller cover.
• A controller should be installed close to each manifold;
• A power outlet is required for the connection of the controller to the mains;
• The mounting locations for the Uponor Control System must be protected from running and dripping water;
• Put one thermostat for every room fitted with a heating floor (one thermostat can control several loops of the heating floor).
3.2 Installation of the components
Mounting the controller (6 or 12-channel)
• Check that the cover of the controller can easily be removed.
• Check that the connectors and switches are easily accessible.
Description3.1 Preparation before installation
3.2Installation of the components(controller and thermostats)
3.3Connections(thermostats and actuators to controller)
3.4 Room thermostats3.5 Floor sensor thermostats4 Finishing the installation
STOP
The controller has to be mounted horizontally. There is a risk for overheating if the controller is mounted vertically or on a horizontal surface.
Drill the wall (Ø6 mm)
Press the anchor into the hole (if concrete wall)
Attach the controller to the wall with screws
1
2
3
Uponor Control System - Installation Manual 7
3.3 Connections
3.3.1 Controller description
6-channel controller
12-channel controller
3.3.2 Connect the actuators to the controller
Example of an installation:
All actuators of a group are controlled by the thermostat connected to the first actuator.Do not "U-Link" with wire. The linking is automatic. The first thermostat controls all following AC output (actuators) if no thermostat is added there. One thermostat can control the whole controller (14 outputs).
In this example, thermostat #01 controls the actuators on terminals 1 to 4.
Thermostat #05 controls the actuator on channel 05 and also controls channels 06 to 11 when no additional thermostat is linked to 06 to 11.
In the following example, thermostat #03 is added, it controls the actuator on channel 03 and also control channel 04.Thermostat #01 controls actuators on channels 01a and 01b and channels 02a and 02b.
99See controller picture in fold-out.
Mark Description
Quick connector for 8 actuators
Power LED
230VAC 50Hz compartment
Quick connector for 6 thermostats
Mark Description
Quick connector for heating / cooling relay
Quick connector for timer
Quick connector for Condense sensor
Quick connector for 14 actuators
Bi-color power LED (red for Heating mode and green for Heating / Cooling mode)
Push-button for Heating or Heating / Cooling mode
230VAC 50Hz compartment
Quick connector for 12 thermostats
1
2
3
4
1
2
3
4
5
6
7
8
99See wiring diagram in the fold-out.
There are two non-polarized wires to connect the thermostat.
8 Underfloor Heating
3.3.3 Controller wiring
Thermostat quick connector on the 6-channel controller:
Thermostat quick connector on the 12-channel controller:
Thermostat connection without timer:Connect one wire of the thermostat to "com" and the other wire to 2.If there is a timer:Connect one wire of the thermostat to "com" and the other wire to 2 if the room requires no timer control. Or connect one wire to "Com" and the other wire to 3 (timer Zone 1) or 4 (timer Zone 2).See explanation on next page.
One of the thermostat's two wires will always be connected to terminal 1 “Com” (non-polarized).
Heating
Com
No timer control
1
2Heating Heating/cooling
Com Com
No timer control No timer control
Timer zone 1 Eco on: Timer control
Timer zone 2Cool Off: No cooling for this room
1
2
3
4
Uponor Control System - Installation Manual 9
3.3.3.1 Connection without Timer option
Connect thermostat and terminal:
"Com" and "No timer": The installation will work in a standard way with the thermostats regulating each room according to their set temperatures. Reduced mode is not available.
Example of an installation wired without Timer:
Thermostat #01 controls the actuator on channels 01a and 01b and channels 02a and 02b.Thermostat #03 controls the actuator on channel 03 and controls channel 04.Thermostat #05 controls the actuator on channel 05 to channel 11.Thermostat #12 controls channel 12.
3.3.3.2 Connection with Timer option in Heating only mode
(Only 12-channel controller)
Connect thermostat and terminal:
• "Com" and "No timer": The installation will work in a standard way with the thermostats regulating each room according to their set temperatures.
• "Com" and "Zone 1" (allocate the thermostat to Zone 1): The corresponding channel will run in Comfort mode according to the time slots in Zone 1 of the timer.
Example: Zone 1 (for settings see timer manual)
• "Com" and "Zone 2" (allocate the thermostat to Zone 2): The corresponding channel will run in Comfort mode according to the time slots in Zone 2 of the timer.
Example: Zone 2 (for settings see timer manual)
To connect the timer, see the wiring diagram in the fold-out.
One of the thermostat's two wires will always be connected to the “Com” quick connector and the second to one of the remaining three quick connectors, depending on the mode selected (non-polarized).
night morning evening night
COMF
ECO
ECO
night evening nightmorning
COMF
10 Underfloor Heating
3.3.3.3 Connection with Timer option in Heating / Cooling mode
Connect thermostat and terminal:
• "Com" and "No timer": When the system is running in Heating mode:The installation will work in a standard way with the thermostats regulating each room according to their set temperatures.When the system is running in Cooling mode:The installation will work in a standard way with the thermostats regulating each room according to their set temperatures.
• "Com" and Timer control: When the system is running in Heating mode:The corresponding channel will run in Comfort mode according to the time slots in Zone 1 of the timer.(for settings see timer manual)
When the system is running in Cooling mode:In Cooling mode, Zone 1 and Zone 2 will be linked in a specific area: automatic overlap of Zone 1 and Zone 2 with specific period "ECO" and "Comfort". This process will take place automatically. The Zone 1 and 2 Comfort mode overrides the Eco mode. The corresponding channel will run in Comfort mode according to the time slots in the specific zone of the timer. This link also enables you to use your cooling unit during the night and to save energy when people are not at home.
• "Com" and "Cool Off": When the system is running in Heating mode:The corresponding channel will run in Comfort mode according to the time slots in Zone 1 of the timer.When the system is running in Cooling mode:There will be no cooling in the room allocated to this thermostat.
Example of an installation wired with a timer:
Thermostat #01 controls channels 01a, 01b, 02a and 02b in "Timer control" (Zone 1) if in Heating mode and "Cool Off" if in Cooling mode.
The following thermostats controls its channels in "No timer" mode.
To connect the timer, see the wiring diagram in the fold-out.
ECO
night morning evening night
COMF
ECO
ECO
ECO
Specific
night morning nightevening
Zone 2
COMF
COMF
COMF
Zone 1
Zone 2 is not used in Heating mode when heating / cooling is active.
One of the thermostat's two wires will always be connected to the “Com” quick connector and the second to one of the remaining three quick connectors, depending on the mode selected (non-polarized).
For more information about Comfort/Eco features, see the timer Manual.
For the 6-channel controller, the thermostat is directly connected to the terminals (non-polarized). Comfort/Eco features are not available.
Uponor Control System - Installation Manual 11
3.3.4 Installation of the options
Different options can be added to the Uponor control system to enhance its features, optimize your comfort and save energy.
3.3.4.1 Timer
The Uponor control system can be equipped with a timer to add energy-saving features and define independent zones. The timer has two programming zones. Each offers four programming options, including one that can be personalized, thus enabling different programmes to be created for each day of the week.
3.3.4.2 Floor sensor
The floor sensor can be used for maximum or minimum limitation of the floor temperature, regardless of the room temperature. It can only be used with the Thermostat Public T-33 and Thermostat T-37. For example, the maximum limitation can protect a sensitive floor covering from exposure to too high temperature when there is a high heat demand. The minimum limitation can keep a tiled floor warm even when there is a no general demand for heat supply to the room. The minimum limitation should not be set to a value higher than the required room temperature.
3.3.4.3 Controller heating / cooling input
If your installation is equipped with a cooling unit, the Uponor control system can be run through a heating / cooling relay.
The controller heating / cooling input operates with the connection of a dry contact.
The contact's control can be either an additional regulation system or a two-position switch.
Connect the heating / cooling relay between terminals 11
and 12 of the controller (symbol ).
Example of wiring:
To configure the controller in Heating / Cooling mode, press the push-button on the controller to switch between modes:
• The LED is red for Heating mode.
• The LED is green for Heating / Cooling mode.
WARNINGMains supply 230VAC 50HzDisconnect the 230V mains before installing or changing the device wiring.
99
See "3.3.3.2 Connection with Timer option in Heating only mode" or "3.3.3.3 Connection with Timer option in Heating / Cooling mode", page 9, 10 for more information on wiring.
99See wiring diagram in the fold-out.
See the timer Manual for more information.
The timer is not available for the 6-channel controller.
99
See "3.5 Thermostat option", page 14 for more information on wiring and setting.
See the floor sensor Manual for more information.
STOP
g
Do not apply voltage to the heating / cooling contact. Damage to the Uponor Control System will occur.
Heating / cooling relay
Heating / cooling contact
Controller heating / cooling input
Example of a different type of heating / cooling relay command
Heating / Cooling mode is not available for the 6-channel controller.
1
2
3
4
12 Underfloor Heating
3.3.4.4 Circulation pump relay
The Uponor Control System can operate a circulation pump on heating/cooling demand. The pump will stop when there is no heat or cooling demand.
Example of an installation:
The controller controls the circulation pump via connection on terminal block (dry contact). There is no power for the pump in the box, just the dry contact.
3.3.5 Connecting the controller to the mains
WARNINGSee the circulation pump supplier documentation before performing the connection.
The electrical circuits of the pump must be protected by a maximum 6A circuit-breaker.
1 Ensure the power is disconnected
2 Open 230V compartment and fix cover to hanger
3 Connect "L" wire from/to pump via relay
4 Close 230V compartment
The pump runs when at least one actuator is active.During actuator exercise, the pump continues to work normally.
1Check that the wiring is complete (actuators, thermostats, pump, timer)
2 Check that the 230V compartment is closed
3 Connect the plug to the mains
Uponor Control System - Installation Manual 13
3.4 ThermostatsThe Uponor Control System may be controlled with three types of thermostats.
• Thermostat T-35 wired:Adjust the temperature with the dial. The dial must be removed to set min/max on the thermostat.
• Thermostat Public T-33 wired:The thermostat is designed for public location.The potentiometers used for the settings are protected with a cover. This thermostat also can be used to connect a floor sensor option.
• Thermostat T-37 wired for floor sensor:Adjust the temperature with the dial. The potentiometers used for the settings are protected with a cover. The dial and the cover must be removed to set up min/max on the thermostat. This thermostat also can be used to connect a floor sensor option.
3.4.1 Opening the thermostats
3.4.2 Mounting and wiring the thermostats
3.4.2.1 Location of a thermostat
(For all thermostats)
• On an indoor wall.
• 1.5 m to 1.8 m from the floor.
• Away from any source of humidity. (IP20)
• Away from any source of heat (television, electronic equipment, fireplace...).
• Away from direct solar radiation.
• Away from direct water splashes.
3.4.2.2 Thermostat fixation
Fixing on the wall:Drill the wall (Ø6 mm). Fix anchors in the wall.Let the screw protrude from the box (3 mm).
Screw the thermostats on the wall or/and on the box.
14 Underfloor Heating
3.4.2.3 Thermostat wiring
Connect the cable from the controller (non-polarized)
3.4.3 Thermostat setup
3.5 Thermostat option
3.5.1 Introduction
Thermostat Public T-33 and Thermostat T-37 allow a floor sensor to be fitted to the system. The temperatures thus measured ensure a more efficient management of the system.
3.5.2 Wiring and setting the floor sensor potentiometer
When a floor sensor is connected to the thermostat to control the temperature of the floor, the limitation of the floor temperature can be adjusted with a potentiometer.The floor sensor settings override the thermostat.Settings:
• Minimum range: 5°C to 35°C.
• Maximum range: 30°C to 40°C
99See: "3.3.3 Controller wiring", page: 8
See Operation Manual for thermostat min/max and room temperature settings.
99
For more information on external sensor settings: See "3.5 Thermostat option".
Open the thermostat cover: see "3.4 Thermostats", page: 13.
Select the required temperature using the potentiometer
1
Uponor Control System - Installation Manual 15
4. Finishing the installation 5. System maintenance5.1 Controller current limitationTo avoid risk of current overload, the controller uses a protection system:
At start-up, 14 actuators cannot be open at the same time. During application, 14 actuators can work at the same time. The controller opens the maximum actuators according to the current limitation.
5.2 Actuator's behaviorThe normal position of an actuator is closed. The controller commands only the opening of an actuator.
5.3 Fallback modeIf a thermostat is short-circuited or not detected, the controller executes the Fallback mode: 7 min open, 14 min closed to maintain the temperature in the room (heating or cooling) until the problem is resolved.If the wire is broken, precedent thermostat will take the command or else Fallback mode is active.
5.4 Automatic exercise functionThe actuators and the pump are designed to avoid seizing, thereby increasing the reliability of the equipment.
This exercise is done every 6 days +/- 0-24 hours at random:Exercise pump and actuators.
The pump exercise operates only if the pump has not been activated since the last exercise. The pump is activated 3 minutes during the exercise.
The actuators exercise operates only if the actuators have not been activated since the last exercise. The exercise consists of opening and completely closing the actuator.
• 5 minutes to open an actuator.
• 9 minutes to close an actuator.
5.5 Resetting InstallationTo reset the Installation, disconnect and reconnect the controller to the mains.
Make a complete check up of the installation:
• Verify that the thermostat covers are in place
• Check that the thermostats are working correctly (turn thermostat dial to obtain a heating demand and make sure that the actuators are running)
Close the cover of the controller
Close the thermostat covers where necessary
Fill in the "Installation report" on the centre pages of booklet
Give the manual and all information about the system to the users
1
2
3
4
16 Underfloor Heating
6. TroubleshootingNormal system operating conditions:
The Power LED of the controller is lit up. The actuators are activated if there is demand for heating or cooling.
*: To find out if a problem is caused by the supply system or the control system. Check the temperatures of the flow and return pipes for the loop(s) corresponding to the room. Loosen the corresponding actuator(s) from the manifold. If the loop temperature starts to rise after a short while (a few minutes for the flow and longer for the return pipe, depending on the floor type), the problem is most likely caused by the room control system. If the temperature remains the same, the problem is in the system (hydraulic).
Failure Causes Indication Solutions Note
room too cold (or
too warm in
Cooling mode) *
thermostat is connected on
a bad channel
■ see Installation report and check
the wiring
■ the LED of the thermostat does
not switch on or off with heating or
cooling demand
actuator does not openthe white indication can not be seen
in the indicator window
■ replace the actuator
■ measure the outputs if 24V when
heat demandthe thermostat is out of
orderreplace the thermostat
room too warm (or
too cold in Heating
mode) *
thermostat is connected on
a bad channel
■ see Installation report and check
the wiring
■ the LED of the thermostat does
not switch on or off with heating or
cooling demand
actuator does not closethe corresponding loop is warm even
after a long period without heat call
■ check that the actuator is
correctly mounted
■ replace the actuatorthe thermostat is out of
orderreplace the thermostat
the floor is cold
■ no heat demand (from
underfloor heating
system)
■ the room is heated by
another heat source
■ The supply water is too
hot. This causes a hot
floor for a short while,
followed by a cold,
uncomfortable floor
room temperature OK, but the floor
is cold
the system does
not start
no voltage power LED off in controller
■ check that the controller is
connected to the mains and that
the wiring in the 230V
compartment is OK
■ check the circuit-breaker in the
principal electrical board
cable breakdown230V in socket but not in 230V
compartmentreplace cable and plug
the thermostat is
not supplied
problem with a terminal
block
the LED of the thermostat does not
switch on or off with heating or
cooling demand
check the terminal
cable breakdown
the LED of the thermostat does not
switch on or off with heating or
cooling demand
replace cable
the thermostat is out of
orderreplace the thermostat
Uponor
Contr
ol Sys
tem
12
-CH
AN
NEL
CO
NT
RO
LLER
WIR
ING
DIA
GR
AM
Mark
Desc
rip
tio
nM
ark
Desc
rip
tio
n
Quic
k co
nnec
tor
for
hea
ting /
coolin
g r
elay
Bi-
colo
r pow
er L
ED
(re
d f
or
Hea
ting m
ode
and g
reen
fo
r H
eating /
Cool
ing m
ode)
Quic
k co
nnec
tor
for
tim
erPush
-butt
on for
Hea
ting o
r H
eating /
Coolin
g m
ode
Quic
k co
nnec
tor
for
Conden
se s
enso
r230VAC 5
0H
z co
mpar
tmen
t
Quic
k co
nnec
tor
for
14
actu
ators
Quic
k co
nnec
tor
for
12
ther
most
ats
15
26
37
48
Tech
nic
al d
ata
Gen
era
l■
IP:
IP20
■M
ax a
mbi
ent RH
(re
lativ
e hu
mid
ity):
95%
max
at 20
°C
Th
erm
ost
at
■CE
mar
king
:-
Low
Voltage
Tes
ts:
EN
60730-1
* a
nd E
N60730-2
-9***
-EM
C (
Ele
ctro
magnet
ic c
om
pat
ibili
ty r
equir
emen
ts)
Tes
ts:
EN
60730-1
and E
N301-4
89-3
■Po
wer
sup
ply:
Fee
d by
wire
s fr
om c
ontr
olle
r■
Volta
ge:
6V
to 1
2V
■O
pera
ting
tem
pera
ture
: 0°
C to
50°C
■St
orag
e te
mpe
ratu
re:
-20°
C to
+70
°C■
Con
sum
ptio
n: <
5m
A■
Wire
the
rmos
tat to
con
trol
ler:
50
m m
ax■
Wire
the
rmos
tat to
sen
sor:
4m
max
.
Co
ntr
oll
er
■CE
mar
king
:-
Low
Voltage
Tes
ts:
EN
60730-1
* a
nd E
N60730-2
-1**
-EM
C T
ests
: EN
60730-1
and E
N301-4
89-3
■Po
wer
sup
ply:
230
VAC +
10/-
15%
50H
z■
Stor
age
tem
pera
ture
: -2
0°C to
+70
°C■
Ope
ratin
g te
mpe
ratu
re:
0°C to
+55
°C■
Con
sum
ptio
n: 9
0W
in fu
ll ch
arge
max
; <
2W
with
out an
y ch
arge
■Pu
mp
rela
y ou
tput
: 23
0VAC
+10
%/-
15%
, 250
VA m
ax. O
nly
Dry
con
tact
■H
eatin
g/co
olin
g in
put:
Onl
y D
ry c
onta
ct■
Valv
e ou
tput
s: 2
4VD
C ±
5%, 21
8m
Am
ax p
er o
utpu
t 3
to 1
224
VDC ±
5%, 4
36m
Am
ax p
er o
utpu
t 1
and
2■
Supp
ly c
onne
ctio
n: E
U -
Plu
g 1
m c
able
, pr
e-m
ount
ed■
Pum
p co
nnec
tion:
wire
s 1.
5mm
² m
ax■
Hea
ting
/ co
olin
g co
nnec
tion:
wire
s 1.
5mm
² m
ax*
EN
60730-1
"Auto
mat
ic e
lect
rica
l co
ntr
ol to
dom
estic
use
".**
EN
60730-2
-1 "
Par
ticu
lar
Req
uirem
ents
for
Ele
ctrica
l Contr
ols
for
Ele
ctri
cal H
ouse
hold
Applia
nce
s".
***EN
60730-2
-9 "
Spec
ific
rule
s fo
r dev
ices
of
ther
mo s
ensi
tive
contr
ol"
.
US
EO
FQ
UIC
KC
ON
NE
CT
OR
S:
Run t
he
cable
in t
he
cable
guid
es (
ther
most
at)
Pres
s, w
ithout
turn
ing, w
ith a
thin
scr
ewdrive
r on t
he
white
butt
on o
f th
e te
rmin
al t
o inse
rt o
r re
mov
e a
wire
Inse
rt a
wire
in t
he
quic
k co
nnec
tor
Rem
ove
the
scre
wdrive
r
Run t
he
cable
in t
he
cable
guid
es t
o b
lock
it
in t
ract
ion (
actu
ator)
Run t
he
ther
most
at c
able
in t
he
clam
p a
nd t
ighte
n t
he
scre
w t
o b
lock
th
em
1 2 3 4 5 6
2U
nder
floor
Hea
ting
INS
TA
LLA
TIO
NR
EP
OR
T
con
tro
ller
nu
mb
er
Ch
an
nels
Ro
om
s
#1
Floor
senso
r
Rel
ay
Yes
24V
No
230V
Pum
p
Yes
No
Tim
er
Yes
No
6-C
HA
NN
EL
CO
NT
RO
LLE
R
Wir
ing
dia
gra
m
Mark
Desc
rip
tio
nM
ark
Desc
rip
tio
n
Quic
k co
nnec
tor
for
8ac
tuato
rs230VAC 5
0H
z co
mpar
tmen
t
Pow
er L
ED
Quic
k co
nnec
tor
for
6th
erm
ost
ats
13
24
Uponor Control System,WiredOperation Manual, UK, IRL
9416
-121
-00
/ IO
M-
V_0
7-02
Rober t Huber in t ie 3bP.O. Box 37FI-01511 VANTAA
+358 (0)20 129 211+358 (0)20 129 2841
I n k e e p i n g w i t h o u r p o l i c y o f c o n t i n u o u s i m p r o v e m e n t a n d d e v e l o p m e n t , U p o n o r r e s e r v e s t h e r i g h t t o c h a n g e s p e c i f i c a t i o n s w i t h o u t p r i o r n o t i c e .
Area managementUponor Hispania S .A.U.Cal le C , n° 24Pol ígono Industr ia l n°1E-28938 Mósto les (Madr id)
+34 91 685 3600+34 91 647 3245www.uponor.es
PO Box 101SE-730 61 Vi rsbo
+46 223 380 00+46 223 381 01
PO Box 1641 ( Industr iest rasse 56)D-97433 Hassfur t
+49 (0)9521 690 0+49 (0)9521 690 150www.uponor.de
Snapethorpe HouseRugby RoadLutterwor thLeicestersh i reLE17 4HN
+44 (0)1455 550355+44 (0)1455 550366www.uponorhous ingsolut ions .co.ukhsenqui r [email protected]
Uponor Control System - Operation Manual 3 3
Table of contents1. General recommendations ............................................................................................................................... 4
2. The Uponor Control System ............................................................................................................................ 5
2.1 Overview of the system.................................................................................................................................. 5
2.2 Operating your installation.............................................................................................................................. 6
3. Thermostat ...................................................................................................................................................... 7
3.1 Changing the temperature setpoint ................................................................................................................. 8
3.2 Setting the min and max temperatures............................................................................................................ 8
3.3 Floor sensor settings..................................................................................................................................... 9
4. System maintenance ....................................................................................................................................... 9
5. Diagnoses and resolution of faults................................................................................................................. 10
5.1 General recommendations ........................................................................................................................... 10
5.2 List of possible failures and solutions............................................................................................................. 11
6. Disposal of the product.................................................................................................................................. 12
4 Underfloor Heating
1. General recommendations
Safety measures• Read and follow instructions.
• Installation must be performed by a qualified person according to local regulations.
• It is prohibited to make changes or modifications not specified in this manual.
• Power must be switched off when carrying out the wiring.
• We decline any responsibility concerning damages and breakdowns that may result from the non-observance of these instructions!
Symbols used in this manual
Power supply
Technical constraintsWARNINGRisk of bodily injuries or pinching.Non observance may harm health or cause damage to product components.
STOP
CAUTIONImportant note on functionality. Non observance of this note may cause malfunctions.
InformationImportant operating advice and information.
See another document.
99See another page in the manual.
WARNING
• The Uponor Control System uses a 230VAC 50Hz power supply.
• In case of emergency, immediately disconnect the plug from the 230V mains.
• Do not use water to clean the Uponor Control System.
• Do not expose the Uponor Control System to flammable vapors or gases.
• Keep installation/data cables away from power cables > 50V to avoid interference.
• The electrical circuits of the boiler and the pump must be protected by a maximum 6A circuit-breaker.
Uponor Control System - Operation Manual 5 5
2. The Uponor Control SystemThe Uponor Control System is a complete management for underfloor heating systems. Comfort, user-friendliness and temperature control for each individual room of your home can be combined through the use of thermostats or floor temperature sensors.
2.1 Overview of the systemThe Uponor Control System consists of thermostats, a controller and actuators. The controller manages the operation of the actuator when the thermostats detect a demand for heating or cooling.
The Uponor Control System may be controlled with the help of three types of thermostats. Designed for maximum comfort, the thermostats communicate with the controller by non polarized two wired system. It's possible to use all kinds of Uponor Control System wired thermostats in the same system.
Thermostat T-35 wired
Thermostat T-35 is easy to use.Temperature settings are be adjusted with a dial.The dial must be removed to set min/max on the thermostat.The 21°C position is marked.
Thermostat Public T-33 wired
The thermostat is for public location. The potentiometers are hidden by a cover. The cover may be removed to allow min/max temperatures to be set. This thermostat also can be used to connect a floor sensor option.
Thermostat T-37 wired for floor sensor
Thermostat T-37 is easy to use.Temperature settings are be adjusted with a dial. The potentiometers are hidden by a cover. The dial and the cover must be removed to set up min/max on the thermostat. This thermostat also can be used to connect a floor sensor option. The 21°C position is marked.
1
2
3
6 Underfloor Heating
2.2 Operating your installationThe Uponor Control System controls your heating installation according to your needs. You simply have to set the temperatures you wish on the thermostats located in each room.
Principle of operation:As soon as the temperature measured at the thermostat is lower than the desired set temperature, it sends this information to the controller, which opens the actuators for this room. Once the set temperature is reached, fresh information is sent and the actuators are closed.
Normal operation without optional timer
When the system is running in normal mode:In Heating mode, the actuators are open when room temperatures are lower than the temperatures set on the thermostat.In Cooling mode, the actuators are open when room temperatures are higher than the temperature set on the thermostat.The actuator position can be seen in the small windows of the actuators.
Operation with optional timer Comfort / Economy features
The use of a timer (option) optimises the installation and conserves energy.
Controller with Thermostats and actuators
6-channel controller:
The controller controls up to 6 thermostats and 8 actuators connected to the hydraulic system of the installation.The controller drives the actuators according to the information received from each thermostat and according to the system parameters settings.The controller is typically located near the hydraulic system manifolds.The window in the actuator shows when a valve is open or closed.
12-channel controller:
The controller controls up to 12 thermostats and 14 actuators connected to the hydraulic system of the installation.The controller drives the actuators according to the information received from each thermostat and according to the system parameters settings.The controller is typically located near the hydraulic system manifolds.The window in the actuator shows when a valve is open or closed.
Several extensions can be added on to the 12 channels controller:
• A timer can be used to add energy saving features and to define the independent zones.
• If your installation is equipped with a cooling unit, the Uponor control system can be run through a heating / cooling relay.
4
If your installation is equipped with this option, see the timer Manual for more information.
Uponor Control System - Operation Manual 7 7
3. Thermostat
Thermostat T-35 and Thermostat T-37
Thermostat Public T-33
Open the thermostat cover: See the Installation manual.
Room temperature setpoint dial control
Terminal for controller connection (non-polarized)
Terminal for floor sensor (non-polarized)
Blue cam for setting minimum temperature
Red cam for setting maximum temperature
Floor sensor potentiometer
Heating / cooling demand LED (Opening / closing of the actuators)
Thermostat uses low voltage 6-12 volt.
1
2
3
4
5
6
7
Screw to open the thermostat
Terminal for controller connection (non-polarized)
Terminal for floor sensor (non-polarized)
Set point temperature potentiometer
Floor sensor potentiometer
Heating / cooling demand LED (Opening / closing of the actuators)
1
2
3
4
5
6
8 Underfloor Heating
3.1 Changing the temperature setpoint
Thermostat T-35 and Thermostat T-37
Thermostat Public T-33
3.2 Setting the min and max temperatures
Thermostat T-35 and Thermostat T-37
A red LED is lit during heating or cooling demand.
Rotate the dial clockwise to get a higher temperature setpoint
Rotate the dial counter-clockwise to get a lower temperature set point
Select the required temperature using the potentiometer
1
2
1
Remove the dial with a screwdriver
Set the minimum temperature with the blue cam
Set the maximum temperature with the red cam
The blue and red cam set the lower and upper ranges from which the set temperature is allowed to deviate.Example:
• The usual set point is 21°C.
• The setting of the blue cam is -10°C.
• The setting of the red cam is +5°C.
➜The temperature range for this room is 11°C to 26°C.
There are no min and max temperature settings for the Thermostat Public.
1
2
3
Uponor Control System - Operation Manual 9 9
3.3 Floor sensor settingsIf your system includes a floor sensor, a potentiometer fitted on the Thermostat Public T-33 and Thermostat T-37 allows you to adjust the minimum or maximum temperature settings for the floor.The floor sensor can be used for maximum or minimum limitation of the floor temperature, regardless of the room temperature.For example, the maximum limitation will protect a sensitive floor covering from exposure to too high temperature when there is a high heat demand. The minimum limitation can keep a tiled floor warm even when there is a no general demand for heat supply to the room.
4. System maintenanceChecks on your system components regularly to optimize performance. This system requires no maintenance.
Automatic exercise function:
The system is fitted with an automatic exercise function. Set every 6 days +/- 24 hours, this function consists of a test-run designed to prevent the pump and actuators from seizing up, when they have not been activated since the last test.
Select the required temperature using the potentiometer
See Installation manual for more information.
1
STOPUse a dry soft cloth to clean the Control System and all it's components. Do not use any detergent.
10 Underfloor Heating
5. Diagnoses and resolution of faultsNormal system operating conditions:
The Power LED of the controller is lit up. The actuators are activated if there is demand for heating or cooling.
5.1 General recommendations
To contact your installer:
See the Installation report in the fold-out to find the contact information for the Installer.
Please prepare the following information before contacting an installer:
• Installation report.
• Drawings of the underfloor heating system (if available).
WARNINGNote that some actions, e.g. actions involving 230V, wiring, etc., are to be performed by a qualified person.
WARNINGRisk of electric shocks. Disconnect the controller from the mains prior to any intervention.
Uponor Control System - Operation Manual 11 11
5.2 List of possible failures and solutions
Failure Causes Indication Solutions Note
the system does
not start
no voltage power LED off in controllercheck the circuit-breaker in the
principal electrical board
contact your
Installer if
necessary
cable breakdown230V in socket but Power LED is
off in controller
contact your
installerthe Thermostat
does not send an
order
the thermostat is out of
order
the LED of the thermostat does
not switch on or off with heating or
cooling demand
contact your
installer
room too cold (or
too warm in
Cooling mode)
thermostat is connected on
a bad channel
■ see Installation report and
check the wiring
■ the LED of the thermostat does
not switch on or off with heating
or cooling demandcontact your
installer
actuator does not openthe white indication can not be
seen in the indicator windowthe thermostat is out of
order
room too warm (or
too cold in Heating
mode)
thermostat is connected on
a bad channel
■ see Installation report and
check the wiring
■ the LED of the thermostat does
not switch on or off with heating
or cooling demand contact your
installer
actuator does not close
the corresponding loop is warm
even after a long period without
heat callthe thermostat is out of
order
the floor is cold
■ no heat demand (from
underfloor heating
system)
■ the room is heated by
another heat source
■ The supply water is too
hot. This causes a hot
floor for a short while,
followed by a cold,
uncomfortable floor
room temperature OK, but the
floor is cold
12 Underfloor Heating
6. Disposal of the productThe Uponor Control System is made up of various recyclable components. Uponor would be grateful if you could sort out these components (batteries, plastics, electric or electronic parts) and dispose of them at a suitable recycling centre.