ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2010 DEH-3300UB/XSUC CRT4634 CD RDS RECEIVER DEH-3300UB /XSUC DEH-3390UB/XNID DEH-3350UB/XNES DEH-3350UB/X1NEC DEH-3350UB/XSES DEH-3350UB/XNES1 This service manual should be used together with the following manual(s): Model No. Order No. Mech. Module Remarks CX-3269 CRT4488 S11.1STD-DOUT CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly For details, refer to "Important Check Points for Good Servicing". K-ZZZ OCT. 2010 Printed in Japan
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
For details, refer to "Important Check Points for Good Servicing".
an
K-ZZZ OCT. 2010 Printed in Japan
C
D
F
A
B
E
1 2 3 4
SAFETY INFORMATION
CAUTION
Where in a manufacturer’s service documentation, for example in circuit diagrams or listsof components, a symbol is used to indicate that a specific component shall be replaced onlyby the component specified in that documentation for safety reasons, the following symbol shallbe used:
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do soand refer the repair to a qualified service technician.
CAUTION:USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
- Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results.
Caution: 1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept. 2. During repair or tests, do not view laser beam for 10 seconds or longer.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm.Health & Safety Code Section 25249.6 - Proposition 65
WARNING!The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1.A specially instructed person should do servicing operation of the apparatus.
CAUTIONThis product is a class 1 laser product classi-fied under the Safety of laser products, IEC60825-1:2007, and contains a class 1M lasermodule. To ensure continued safety, do not re-move any covers or attempt to gain access tothe inside of the product. Refer all servicing toqualified personnel.
CAUTION—CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN, DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
DEH-3300UB/XSUC21 2 3 4
C
D
F
A
B
E
5 6 7 8
Laser diode characteristicsWave length : 785 nm to 814 nm
Maximum output : 1 190 µW(Emitting period : unlimited)
Additional Laser Caution
Transistors Q101 in PCB drive the laser diodes.When Q101 is shorted between their terminals, the laser diodes will radiate beam.If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam.
CAUTIONDanger of explosion if battery is incorrectly replaced.Replaced only with the same or equivalent type recommended by the manufacture.Discord used batteries according to the manufacture's instructions.
DEH-3300UB/XSUC 35 6 7 8
C
D
F
A
B
E
1 2 3 4
[Important Check Points for Good Servicing]In this manual, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
DEH-3300UB/XSUC41 2 3 4
C
D
F
A
B
E
5 6 7 8
CONTENTS SAFETY INFORMATION .....................................................................................................................................21. SERVICE PRECAUTIONS................................................................................................................................6
1.1 SERVICE PRECAUTIONS .........................................................................................................................61.2 NOTES ON SOLDERING...........................................................................................................................8
3. BASIC ITEMS FOR SERVICE ........................................................................................................................133.1 CHECK POINTS AFTER SERVICING .....................................................................................................133.2 PCB LOCATIONS.....................................................................................................................................143.3 JIGS LIST .................................................................................................................................................153.4 CLEANING ...............................................................................................................................................15
6. SERVICE MODE.............................................................................................................................................226.1 DISPLAY TEST MODE.............................................................................................................................226.2 CD TEST MODE.......................................................................................................................................23
7. DISASSEMBLY ...............................................................................................................................................248. EACH SETTING AND ADJUSTMENT............................................................................................................30
8.1 CD ADJUSTMENT ...................................................................................................................................308.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT ....................................................318.3 PCL OUTPUT CONFIRMATION...............................................................................................................33
9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................349.1 PACKING ..................................................................................................................................................349.2 EXTERIOR ...............................................................................................................................................369.3 CD MECHANISM MODULE .....................................................................................................................38
10. SCHEMATIC DIAGRAM................................................................................................................................4010.1 TUNER AMP UNIT (GUIDE PAGE)........................................................................................................4010.2 KEYBOARD UNIT ..................................................................................................................................4610.3 CD CORE UNIT (S11.1STD-DOUT) ......................................................................................................4810.4 WAVEFORMS.........................................................................................................................................50
11. PCB CONNECTION DIAGRAM ....................................................................................................................5211.1 TUNER AMP UNIT .................................................................................................................................5211.2 KEYBOARD UNIT ..................................................................................................................................5611.3 CD CORE UNIT (S11.1STD-DOUT) ......................................................................................................58
12. ELECTRICAL PARTS LIST ...........................................................................................................................60
DEH-3300UB/XSUC 55 6 7 8
C
D
F
A
B
E
1 2 3 4
1. SERVICE PRECAUTIONS1.1 SERVICE PRECAUTIONS
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit.3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY".4. After replacing the pickup unit, be sure to check the grating.5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction.6. area and a heat sink becomes hot areas. Be careful not to burn yourself.
7. Software update The software of this product is stored in IC671. Please replace IC671 when making the version upgrade of software.8. How to Handle Infrared Deteching unit for Remote Control of Grille The infrared deteching unit for remote control of keyboard unit is not fixed with cushion, etc. When external force is applied on the infrared deteching unit for remote control, the light receiving sensitivity might be deteriorated since the lead bents and attaching angle of the light receiving part may be varied. Please do not apply external force onto the infrared deteching unit for remote control. If any external force is applied by mistake, please confirm whether lead bending may exist or not. If the lead is bent, please correct the angle between the lead and the light receiving part to be 90 degrees or replace the infrared deteching unit for remote control (GP1UXC14RK).
DEH-3300UB/XSUC61 2 3 4
C
D
F
A
B
E
5 6 7 8
10. Capacitor Bond Lock (ID, ES, EC, ES1) Silicon Glue (GEM1017) Place the capacitor in the center of the silk print, and confirm it does not touch to the connector. Then, apply silicon glue.
OK NG
9. Capacitor Bond Lock (UC) Acetate Tape (GYH1026)
1 Please stick acetate tape along white line.2 Please confirm line hiding with acetate tape.
* length of tape : 24 ± 4 mm1 2
DEH-3300UB/XSUC 75 6 7 8
C
D
F
A
B
E
1 2 3 4
1.2 NOTES ON SOLDERING
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia.
DEH-3300UB/XSUC81 2 3 4
C
D
F
A
B
E
5 6 7 8
2. SPECIFICATIONS2.1 SPECIFICATIONS
General
DEH-4300UB/XNUC, DEH-3300UB/XSUC
Power source.............................14.4 V DC (10.8 V to 15.1 Vallowable)
Grounding system...................Negative typeMaximum current consumption
.....................................................10.0 A
Dimensions (W × H × D):DIN
Chassis.....................178 mm × 50 mm × 165mm(7 in. × 2 in. × 6-1/2 in.)
Nose...........................188 mm × 58 mm × 17 mm(7-3/8 in.× 2-1/4 in.× 5/8 in.)
DChassis.....................178 mm × 50 mm × 165
mm(7 in.× 2 in.× 6-1/2 in.)
Nose...........................170 mm × 46 mm × 17 mm(6-3/4 in.× 1-3/4 in.× 5/8 in.)
Weight ..........................................1.2 kg (2.64 lbs)
AudioMaximum power output .......50 W × 4Continuous power output ...22 W × 4 (50 Hz to 15 000
Hz, 5 % THD, 4 load, bothchannels driven)
Load impedance ......................4 (4 to 8 allowable)Preout maximum output level
BassFrequency................100 HzGain ............................±12 dB
MidFrequency................1 kHzGain ............................±12 dB
TrebleFrequency................10 kHzGain ............................±12 dB
Subwoofer (mono):Frequency..........................50/63/80/100/125 HzSlope....................................–18 dB/octGain ......................................+6 dB to –24 dBPhase ..................................Normal/Reverse
CD playerSystem..........................................Compact disc audio systemUsable discs ..............................Compact discSignal-to-noise ratio...............94 dB (1 kHz) (IHF-A net-
work)Number of channels ..............2 (stereo)
Backup current .......................4.0 mA or less
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12(2ch audio)(Windows Media Player)
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3WAV signal format ..................Linear PCM & MS ADPCM
(Non-compressed)
USBUSB standard specification
.....................................................USB 2.0 full speedMaximum current supply ....500 mAUSB Class...................................MSC (Mass Storage Class)File system..................................FAT12, FAT16, FAT32WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)(Windows Media Player)
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3WAV signal format ..................Linear PCM & MS ADPCM
(Non-compressed)
FM tunerFrequency range......................87.9 MHz to 107.9 MHzUsable sensitivity.....................9 dBf (0.8 µV/75 , mono,
S/N: 30 dB)Signal-to-noise ratio...............72 dB (IHF-A network)
AM tunerFrequency range......................530 kHz to 1 710 kHzUsable sensitivity.....................25 µV (S/N: 20 dB)Signal-to-noise ratio...............62 dB (IHF-A network)
CEA2006 Specifications
Power output .............................14 W RMS × 4 Channels (4and 1 % THD+N)
S/N ratio .......................................91 dBA (reference: 1 W into4 )
NoteSpecifications and the design are subject to mod-ifications without notice.
BassFrequency................100 HzGain ............................±12 dB
MidFrequency................1 kHzGain ............................±12 dB
TrebleFrequency................10 kHzGain ............................±12 dB
Subwoofer (mono):Frequency..........................50/63/80/100/125 HzSlope....................................–18 dB/octGain ......................................+6 dB to –24 dBPhase ..................................Normal/Reverse
CD playerSystem..........................................Compact disc audio systemUsable discs ..............................Compact discSignal-to-noise ratio...............94 dB (1 kHz) (IEC-A net-
work)Number of channels ..............2 (stereo)WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)(Windows Media Player)
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WAV signal format ..................Linear PCM & MS ADPCM(Non-compressed)
USBUSB standard specification
.....................................................USB 2.0 full speedMaximum current supply ....500 mAUSB Class...................................MSC (Mass Storage Class)File system..................................FAT12, FAT16, FAT32WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)(Windows Media Player)
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3WAV signal format ..................Linear PCM & MS ADPCM
(Non-compressed)
FM tunerFrequency range......................87.5 MHz to 108.0 MHzUsable sensitivity.....................9 dBf (0.8 µV/75 , mono,
S/N: 30 dB)Signal-to-noise ratio...............72 dB (IEC-A network)
AM tunerFrequency range......................531 kHz to 1 602 kHz (9 kHz)
530 kHz to 1 640 kHz (10kHz)
Usable sensitivity.....................25 µV (S/N: 20 dB)Signal-to-noise ratio...............62 dB (IEC-A network)
Infrared remote control (ES, ES1 model)Wavelength.................................940 nm ±50 nmOutput ...........................................typ; 12 mw/sr per Infrared
LED
NoteSpecifications and the design are subject to mod-ifications without notice.
Backup current .......................4.0 mA or less
DEH-3300UB/XSUC101 2 3 4
C
D
F
A
B
E
5 6 7 8
2.3 PANEL FACILITIES
Head unit
12 4 5 63
7 8 a b c d9
traPtraP
1 S (SRC/OFF) 8(Back/display/
scroll)
2 (eject) 9
3 (list) a /DISP OFF (ID, ES, EC)
4MULTI-CONTROL(M.C.)
b 1 to 6
5 Disc loading slot cAUX input jack (3.5mm stereo jack)
6 USB port d Detach button
7 B (BAND/ESC)
CAUTIONUse an optional Pioneer USB cable (CD-U50E)to connect the USB audio player/USB mem-ory as any device connected directly to theunit will protrude out from the unit and maybe dangerous.Do not use unauthorized products.
Remote control
e
k
i
f
h
gj
7
1
9
Part Operation
e VOLUMEPress to increase or decrease vo-lume.
f MUTEPress to mute. Press again to un-mute.
g AUDIO Press to select an audio function.
h DISP/SCRLPress to select different displays.Press and hold to scroll throughthe text information.
iPress to pause or resume play-back.
j FUNCTION
Press to select functions.Press and hold to recall the initialsetting menu when the sourcesare off.
kLIST/ENTER
Press to display the disc title,track title, folder, or file list de-pending on the source.While in the operating menu,press to control functions.
Display indication
4563 8
a b9
1
27
Indicator State
1Main dis-play sec-tion
Tuner: band and frequencyBuilt-in CD, USB storage de-vice and iPod: elapsed play-back time and textinformation
2An upper tier of folder or menuexists.
3
A lower tier of folder or menu ex-ists.It flashes when a song/album re-lated to the song currently playingis selected from iPod.
4 (list) The list function is operated.
5 (artist)The artist name is displayed.Artist search refinement of theiPod browsing function is in use.
6 (disc)
The disc (album) name is dis-played.Album search refinement of theiPod browsing function is in use.
7 (song)
The track (song) name is dis-played.A playable audio file has been se-lected while operating the list.Song search refinement of theiPod browsing function is in use.
8 LOC The local seek tuning is on.
9 (repeat) Track or folder repeat is on.
a(ran-
dom/shuf-fle)
Random play is on.The iPod source is selected andthe shuffle or shuffle all functionis on.
b (sound re-triever)
The sound retriever function ison.
DEH-3300UB/XSUC 115 6 7 8
C
D
F
A
B
E
1 2 3 4
2.4 CONNECTION DIAGRAM
This unit1
4 5 6
2 3
1 Power cord input2 Rear output or subwoofer output3 Front output4 Antenna input5 Fuse (10 A)6 Wired remote input
Hard-wired remote control adaptor can beconnected (sold separately).
Power cordPerform these connections when not connect-ing a rear speaker lead to a subwoofer.
1
89
cd
6
32
4
5
7
ab
e
f
hg
RL
F
R
Perform these connections when using a sub-woofer without the optional amplifier.
1
89
cd
6
32
4
7
ab
a
b
e
f
hg
RL
F
SW
i
j
d
ck l
1 To power cord input2 Left3 Right4 Front speaker5 Rear speaker6 White7 White/black8 Gray9 Gray/blacka Greenb Green/blackc Violetd Violet/blacke Black (chassis ground)
Connect to a clean, paint-free metal location.
f YellowConnect to the constant 12 V supply terminal.
g RedConnect to terminal controlled by ignitionswitch (12 V DC).
h Blue/whiteConnect to system control terminal of thepower amp or auto-antenna relay controlterminal (max. 300 mA 12 V DC).
i Subwoofer (4 )j When using a subwoofer of 70 W (2 ), be
sure to connect the subwoofer to the violetand violet/black leads of this unit. Do not con-nect anything to the green and green/blackleads.
k Not used.l Subwoofer (4 )× 2
NotesWith a 2 speaker system, do not connect any-thing to the speaker leads that are not con-nected to speakers.Change the initial setting of this unit. Refer toSW CONTROL (rear output and subwoofer set-ting).The subwoofer output of this unit is monaural.
Power amp (sold separately)Perform these connections when using theoptional amplifier.
1 3
24
55
1
1
3
24
55
3
26
77
1 System remote controlConnect to Blue/white cable.
2 Power amp (sold separately)3 Connect with RCA cables (sold separately)4 To Rear output or subwoofer output5 Rear speaker or subwoofer6 To Front output7 Front speaker
Fastening the front panelIf you do not plan to detach the front panel, the front panel can be fastened with the supplied screw.
Screw (BPZ20P060FTC) (UC) (XXX7020) (ID, ES)
DEH-3300UB/XSUC121 2 3 4
C
D
F
A
B
E
5 6 7 8
3. BASIC ITEMS FOR SERVICE3.1 CHECK POINTS AFTER SERVICING
To keep the product quality after servicing, please confirm following check points.
demrifnocebotmetIserudecorP.oN1 Confirm whether the customer complain has
been solved.If the customer complain occurs with thespecific media, use it for the operation check.
The customer complain must not bereappeared.Display, audio and operations must benormal.
2 CD Play back a CD.(Track search)
No malfunction on display, audio andoperation.
3 FM/AM tuner Check FM/AM tuner action.(Seek, Preset)Switch band to check both FM and AM.
Display, audio and operations must benormal.
4 Check whether no disc is inside the product. The media used for the operating check mustbe ejected.
retfaecnaraeppastinotridrosehctarcsoNkcehcecnaraeppA5receiving it for service.
See the table below for the items to be checked regarding audio:
Item to be checked regarding audioDistortionNoiseVolume too lowVolume too highVolume fluctuatingSound interrupted
DEH-3300UB/XSUC 135 6 7 8
C
D
F
A
B
E
1 2 3 4
3.2 PCB LOCATIONS
A
B Keyboard Unit
Tuner Amp Unit
A:DEH-3300UB/XSUC
B:DEH-3390UB/XNID
C:DEH-3350UB/XNES
D:DEH-3350UB/X1NEC
E:DEH-3350UB/XSES
F:DEH-3350UB/XNES1
Unit Number : CWN5477(A)
: CWN5478(B,C,D,E,F)
Unit Name : Tuner Amp Unit
Unit Number :
Unit Name : Keyboard Unit
Unit Number : CWX3985
Unit Name : CD Core Unit (S11.1STD-DOUT)
CD Core Unit (S11.1STD-DOUT)C
DEH-3300UB/XSUC141 2 3 4
C
D
F
A
B
E
5 6 7 8
3.3 JIGS LIST
3.4 CLEANING
- Jigs List
- Grease List NameGreaseGreaseGreaseGreaseSilicon Glue
In case of the above signal, the communicationwith Grille microcomputer may fail.If the time interval is not 300 msec, the oscillatormay be defective.
Completes power-on operation.(After that, proceed to each source operation)
Power ON
ASENS = L
DEH-3300UB/XSUC181 2 3 4
C
D
F
A
B
E
5 6 7 8
5.2 ERROR CODE LIST
8-digit display 6-digit display 4-digit display
ERROR-xx ERR-xx E-xx
(2) LIST OF CD ERROR CODES (Error Mode: 0xFD)
Code Classification Error code to be displayed Details and possible causes
10 Servo Carriage Home NG The CRG cannot move toward the inner track.The CRG cannot move from the inner track.--> Defective HOME SW; Failure in CRG movement.
7 Servo TOC reading NG TOC information cannot be read. --> The partial disk or TOC content is illegal.
11 Servo Focus Search NG Focusing not available--> Disc placed upside-down; Stains on the disc; excessive vibration.
17 Servo Setup NG AGC protection does not work. Focus can be easily lost.--> Scratches or stains on the disc; excessive vibration.
15 Servo Failure in RF data RF not read--> A CD-R disc that does not contain data loaded--> A CD-RW disc that does not contain data loaded
12 Servo Spindle Lock NGSubcode NGRF-amp NG
Spindle not locked. Subcode not readable.Proper RF AMP gain not obtained.--> Defective spindle; Scratches or stains on the disc; excessive vibration.--> A CD-R disc that does not contain data loaded, or in a rare case, disc placed upside-down.--> CD signal error.
30 Servo Search Time Out Failed to reach a target address--> CRG tracking error; Scratches on the disc; Stains on the disc
50 Mechanism Failure in ejectionLoad NG
Disc ejection not completedDisc loading not completed--> A foreign object inserted in the mechanism; Disc jammed.
51 Mechanism Failure in retriedturning for ejection
Disc could not be ejected even after disc turning had been retried.--> A foreign object inserted in the mechanism; Disc jammed.
NOTES• Indications of error codes are available only during disc operations, because CD operations are unavailable if a mechanical error is generated.• If the TOC cannot be read, this is not processed as an error, and operation continues accordingly.• If you design a new head unit, be sure to use one of the display formats indicated in “Display example of the main unit.”
ERROR CODES
(1) DISPLAY METHODIf “0xFD” error mode is displayed in CD MODE (CD MODE area for display), an error code will be displayed in the MIN (minute display) and SEC (second display) areas.
The same code is displayed in the MIN and SEC areas.The TNO area is blank (#0FFH), as it conventionally was.• Display example of the main unit Depending on the display capability of LCDs, the display format varies, as shown below. XX denotes an error number. Note: In a case of an OEM product, the error display format is subject to the specifications used by the equipment manufacturer.
If a CD memory device is inoperable, or operation of such media is stopped by an error, the error mode is established and a cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from customers and facilitate failure analysis and repair work in servicing.
• The 2 high-order digits of an error code denote the main classification, shown below. 0x: Servo-related errors 1x: Servo-related errors 3x: Servo-related errors 5x: Mechanism-related errors
• How to restore from each error is shown below. 0x, 1x and 3x: ACC-OFF then ON, CD-OFF then ON, Disc ejection 5X: ACC-OFF then ON, Disc ejection, Disc reloading
DEH-3300UB/XSUC 195 6 7 8
C
D
F
A
B
E
1 2 3 4
USB storage device/iPod
Message Cause Action
NO DEVICE When plug andplay is off, noUSB storage de-vice or iPod isconnected.
Turn the plugand play on.
Connect a com-patible USB sto-rage device/iPod.
FRMT READ Sometimes thereis a delay be-tween the start ofplayback andwhen you start tohear any sound.
Wait until the mes-sage disappearsand you hearsound.
NO AUDIO There are nosongs.
Transfer the audiofiles to the USBstorage device andconnect.
The connectedUSB storage de-vice has securityenabled
Follow the USBstorage device in-structions to dis-able the security.
Play an audio filenot embedded withWindows MediaDRM 9/10.
PROTECT All the files in theUSB storage de-vice are em-bedded withWindows MediaDRM 9/10
Transfer audio filesnot embedded withWindows MediaDRM 9/10 to theUSB storage de-vice and connect.
N/A USB The connectedUSB storage de-vice is not sup-ported by thisunit.
Connect a USBMass StorageClass compliantdevice.
Disconnect yourdevice and replaceit with a compati-ble USB storagedevice.
Message Cause Action
CHECK USB The USB connec-tor or USB cablehas short-circuited.
Check that theUSB connector orUSB cable is notcaught in some-thing or damaged.
The connectedUSB storage de-vice consumesmore than 500mA (maximumallowable cur-rent).
Disconnect theUSB storage de-vice and do notuse it. Turn theignition switch toOFF, then to ACCor ON and thenconnect only com-pliant USB storagedevices.
The iPod oper-ates correctly butdoes not charge
Make sure the con-nection cable forthe iPod has notshorted out (e.g.,not caught inmetal objects).After checking,turn the ignitionswitch OFF andback ON, or dis-connect the iPodand reconnect.
ERROR-19 Communicationfailed.
Perform one ofthe following op-erations.–Turn the ignitionswitch OFF andback ON.–Disconnect theUSB storage de-vice.–Change to a dif-ferent source.Then, return to theUSB source.
Disconnect thecable from theiPod. Once theiPod's main menuis displayed, recon-nect the iPod andreset it.
iPod failure Disconnect thecable from theiPod. Once theiPod's main menuis displayed, recon-nect the iPod andreset it.
ERROR-23 USB storage de-vice is not for-matted withFAT12, FAT16 orFAT32
USB storage de-vice should be for-matted with FAT12,FAT16 or FAT32.
ERROR-16 The iPod firm-ware versions areold.
Update the iPodversion.
iPod failure Disconnect thecable from theiPod. Once theiPod's main menuis displayed, recon-nect the iPod andreset it.
STOP There are nosongs in the cur-rent list.
Select a list thatcontains songs.
NOT FOUND No related songs Transfer songs tothe iPod.
DEH-3300UB/XSUC201 2 3 4
C
D
F
A
B
E
5 6 7 8
5.3 CONNECTOR FUNCTION DESCRIPTION
REAR OUTPUT SUBWOOFER OUTPUT
ANTENNA
FRONT OUTPUT(Except DEH-3300UB/XSUC)
1 FL+2 FR+3 FL-4 FR-5 RL+6 RR+7 RL-8 RR-
9 NC10 NC11 NC12 NC13 ACC14 B.REM15 B.UP16 GND
16 14 12 10 8 6 4 2
15 13 11 9 7 5 3 1
WIRED REMOTE CONTROL(Except DEH-3300UB/XSUC)
DEH-3300UB/XSUC 215 6 7 8
C
D
F
A
B
E
1 2 3 4
6. SERVICE MODE6.1 DISPLAY TEST MODE
* Initial condition
S $ $ $ $ # # #
$ PD number
For Ver.7.01, "701" is displayed
For PEA010A, "010A" is displayed
# System microcomputer version
1 + 3
On (state when entering test mode)
Press “ 1 ” and “ 3 ” keys simultaneously to start resetting.
[Operation key]
[How to enter Test mode]
[Test items]Start display test mode (2). (Press “ 1 ” + “ 3 ” keys simultaneously to start resetting.)
Display is normally updated
Display update is stopped
Product operation is performed as usual, in appearance.
The screen gets still when entering this item.
On (an initial value)
On (lighting condition of normal times)
On (an initial value or setting value of default menu)
On (an initial value or setting value of default menu)
On (an initial value or setting value of default menu)
Off All off
All off
All off
Remarks
Key Illumination
Operation key Processing
Icon
Enter display test mode (2)Switch to next test mode
The information such as the system microcomputer version is checked.
Switching to next displayby pressing “ 1 ” + “ 3 ” keys simultaneously.
Switching to next displayby pressing “ 1 ” + “ 3 ” keys simultaneously.
Switching to next displayby pressing “ 1 ” + “ 3 ” keys simultaneously.
DEH-3300UB/XSUC221 2 3 4
C
D
F
A
B
E
5 6 7 8
6.2 CD TEST MODE
[Key]
Contents
Display
[BAND]
Power On(T.Offset is adjusted)TRK MIN SEC00 00 00
[2]
RF AMPGain switching
GG GG GG
*1
[3]
Focus CloseS curve check
TRK MIN SEC91 91 91
[6]
Focus Mode switching
0X 0X 0X
*2
[1]
Tracking ServoClose
00 00 00or 99 99 99
[<]
CRG +
[2]
Self-adjustingswitching
TRK MIN SEC?? ?? ??
*3*8
[>]
CRG -*8
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[1]T.Close & AGC
Applicable servomechanism
TRK MIN SEC?tr ?min ?sec
[3]
RF AGC /RF AGC coefficient display
[<]
CRG +
8X 8X 8Xor 9X 9X 9X
[2]
T.Balance adjustment /T.BAL coefficient display
TRK MIN SEC?? ?? ??
[>]
CRG -
?? ?? ??
[1]
F,T,RF AGCF.Bias display switchingTRK MIN SEC
TRK MIN SEC
TRK MIN SEC
[3] [<]
CRG/TR Jump +
[2]
Tracking Open
[>]
CRG/TR Jump -
?tr ?min ?sec
TRK MIN SEC
TRK MIN SEC
00 00 00or 99 99 99
TRK MIN SEC?tr ?min ?sec
8X 8X 8Xor 9X 9X 9X
8X 8X 8Xor 9X 9X 9X
00 00 00or 99 99 99
TRK MIN SEC?tr ?min ?sec?? ?? ??
*7 F,T AGC / F.BiasRF AGC
8X 8X 8Xor 9X 9X 9X
[2]
Tracking Open
*6
*4 *4
Operation[Key] Test Mode
[BAND] Power On/Off[<] CRG + / TR Jump +
(Direction of the external surface)[>] CRG - / TR Jump -
(Direction of the internal surface)[1] T. CLS & AGC & Applicable servomechanism /
T.Balance adjustment / T. Open[3] F. Close,S. Curve / Rough Servo and RF AGC /
F,T,RF AGC[6] F. Mode switching / Tracking Close
After the [EJECT] key is pressed keys other than the [EJECT] key should not be pressed, until disc ejection is complete.When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens sticks to Wall, causing the actuator to be damaged).100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting.Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows)
- Flow Chart[CD] or [SOURCE]
Source ON
TRK MIN
[4] + [6] -> BUP + ACC ON
Test Mode IN
*1) TYP t + 6 dB t + 12 dB TRK MIN SEC TRK06MIN06SEC06 TRK12MIN12SEC12
*2) Focus Close t S. Curve t F EQ measurement setting TRK00MIN00SEC00
TRK01MIN01SEC01 TRK02MIN02SEC02 (TRK99MIN99SEC99)
*3) F.Offset Display t T.Offset Display t Switch to the order of the original display
*4) 100TR Jump
*7) TRK/MIN/SEC t F.AGC t T.AGC Gain t F.Bias t RF AGC
*8) CRG motor voltage = 2 [V]
*9) TYP (1X) t 2X t 1X TRK MIN SEC
TRK22MIN22SEC22 TRK11MIN11SEC11*10) OFF(TYP) t FORCUS t TRACKING TRK MIN SEC
TRK70MIN70SEC70 TRK71MIN71SEC71
DEH-3300UB/XSUC 235 6 7 8
C
D
F
A
B
E
1 2 3 4
7. DISASSEMBLY
2
3
Fig.1
Fig.2
Fig.3
1
- Removing the Panel Assy (Fig.1)
Remove the two hooksand then remove the Panel Assy.
Remove the two hooks.
1
2 Remove the two screws.
Remove the screw.
Lift off the Tuner Amp Assy from the Heat sink side.
4
- Removing the CD Mechanism Module (Fig.2, 3, 4)
The CD Mechanism Module side is made a bottom.
Fig.4
5
6
Push the area and remove the two hooks.
Slide the Tuner Amp Assy in the direction of the arrowand then remove the hooks of upper and lower.
The Tuner Amp Unit is fixed into the ditch.
Disconnect the FFCand then remove the CD Mechanism Module.
Panel Assy
22
CD Mechanism Module
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
3
3
1
Heat sink side
CD Mechanism ModuleTuner Amp Assy
5
5
6
1
22
1
DEH-3300UB/XSUC241 2 3 4
C
D
F
A
B
E
5 6 7 8
3
Fig.5
1
- Removing the Tuner Amp Unit (Fig.5)
Straighten the tabs at two locations indicatedand then remove the Tuner Amp Unit.
2
Remove the two screws.
Remove the two screws.
- Attention of removing (Fig.6)
Fig.6
Don't remove this screws excluding the dismantlement of the CD Mechanism Module.
Tuner Amp Unit
1 1
2
2
3
3
DEH-3300UB/XSUC 255 6 7 8
C
D
F
A
B
E
1 2 3 4
Fig.7
Fig.8
Fig.9
Fig.10
- Disassembling the Panel Part (Fig.7, 8)
2. Press the upside hook and the bottom side hook of the button at the same time, and pull out the button.
1. Remove the arm while bending the rib of the panel upward.
- Assembling the Panel Part (Fig.9, 10, 11)
1. Attach the button from the front side of the panel.
2. Attach the spring to the arm as shown in the figure.
Hitch the spring to the groove.
The bended tip of the spring is set to this side.
DEH-3300UB/XSUC261 2 3 4
C
D
F
A
B
E
5 6 7 8
Fig.11
3. Fit the spring in the groove at the position shown in the figure.
4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel.
DEH-3300UB/XSUC 275 6 7 8
C
D
F
A
B
E
1 2 3 4
Correct way of holding the unit
Incorrect way of holding the unit
How to carry the mecha unit
1. Hold the designated points (shown with dashed lines) of the upper chassis and the front/rear bracket.2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less)
DEH-3300UB/XSUC281 2 3 4
C
D
F
A
B
E
5 6 7 8
Slide toward inner circumference
Normal built-in state
The spring is below a resin flange and is built inside the sheet metal bending.
[Incorrect built-in state]The chassis is not nipped between the PU case and the PU rack.Outer holder
Rear end of feeding screw
Fig 1
Fig 3 Fig 4
Fig 2a
Fully-hooked state
B
Tentatively-hooked state
Fig 2b
A
How to remove the PU unit
1. Create an empty-clamp state according to “How to create empty clamp state (motor drive)”.2. Hook the feeding screw biasing spring to a tentative hooking portion (Fig 2b). Be careful not to get injured by the spring edge.3. Hold the PU at the position A as shown in Fig 1. Slide the PU as far as possible toward the holder in the feeding screw so that a joint on the outer end of the feeding screw is loosened.4. As shown in Fig 3, move the rear end of the feeding screw laterally and then upward, to remove it from the outer holder.5. Lift the PU unit to disengage it from Part B of the chassis (Fig 4), and remove the PU unit. (Cautions) When re-installing the PU, be sure to first nip the chassis and the PU unit (Fig 4) at the position B. Also, make sure to fully hook the feeding screw biasing spring (Fig 2a). Please follow the service manual for adjustment of the PU unit after the re-installation.
How to move the PU to the outer circumference
1. Create an empty clamp state according to “How to create empty clamp state of mecha module”.2. Apply 1.5 V to the CRG motor and move the PU to the outer circumference. (Caution) After moving the PU to the outer circumference and performing necessary treatment, make sure to solder the lead wires.
DEH-3300UB/XSUC 295 6 7 8
C
D
F
A
B
E
1 2 3 4
8. EACH SETTING AND ADJUSTMENT8.1 CD ADJUSTMENT
1) Cautions on adjustments In this product the single voltage (3.3 V) is used for the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND.If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems:a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state.c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately.
Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator.
For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on.
In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment.
The RFAGC and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series.
The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it.
2) Test modeThis mode is used to adjust the CD mechanism module. To enter the test mode.[4] + [6] -> BUP + ACC ON
To exit from the test mode.Turn off the ACC and back up.
Notes:a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected.b. If you have pressed the ( ) key or ( ) key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck.c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released.d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released.e. When the power is turned off and on, the jump mode is reset to the single TR (91), the RF amp gain is set to 0 dB, and the auto-adjustment values are reset to the default settings.
DEH-3300UB/XSUC301 2 3 4
C
D
F
A
B
E
5 6 7 8
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
FE
REFO1
CD CORE UNIT
Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
Purpose :To check that the grating is within an acceptable range when the PU unit is changed.
Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching.
Method : Measuring Equipment Measuring Points
Oscilloscope, Two L.P.F. E, F, REFO1
Disc TCD-782 Mode TEST MODE
Checking Procedure1. In test mode, load the disc and switch the 3 V regulator on.2. Using the right and left buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press.4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 . Refer to the photographs supplied to determine the phase angle.5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle.
HintReloading the disc changes the clamp position and may decrease the "wobble".
100 kohm
390 pF
100 kohm
390 pF
E
VREF
F
VREF
Xch Ych
L.P.F.
L.P.F.
Oscilloscope
DEH-3300UB/XSUC 315 6 7 8
C
D
F
A
B
E
1 2 3 4
Grating waveform
45 degrees
0 degrees
75 degrees
60 degrees
30 degrees
90 degrees
Ech -> Xch 20 mV/div, ACFch -> Ych 20 mV/div, AC
DEH-3300UB/XSUC321 2 3 4
C
D
F
A
B
E
5 6 7 8
8.3 PCL OUTPUT CONFIRMATION
- PCL outputWith the TESTIN (22 pin) status of IC601 to be “H”, it is shifted to PCL Output Test mode after reset started.Check that square wave of 600.0 kHz is output from PCL (8 Pin) of IC601.If clock signal is out of this range, this resonator (X602) must be changed for a new one.
DEH-3300UB/XSUC 335 6 7 8
C
D
F
A
B
E
1 2 3 4
9. EXPLODED VIEWS AND PARTS LIST
9.1 PACKING
NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.)
""
DEH-3300UB/XSUC341 2 3 4
C
D
F
A
B
E
5 6 7 8
PACKING SECTION PARTS LIST
Owner's Manual,Installation Manual
Mark No. DescriptionDEH-3300UB/
XSUCDEH-3390UB/
XNIDDEH-3350UB/
XNESDEH-3350UB/
X1NECDEH-3350UB/
XSESDEH-3350UB/
XNES1 1 Polyethylene Bag CEG1173 QEG3001 QEG3001 Not used QEG3001 QEG3001 2 Unit Box CHG7454 CHG7458 CHG7455 Not used CHG7456 CHG7457 3 Contain Box CHL7454 CHL7458 CHL7455 Not used CHL7456 CHL7457 4 Cord Assy QDP3013 QDP3013 QDP3013 QDP3014 QDP3013 QDP3013* 5 Accessory Assy QEA3008 QEA3009 QEA3009 Not used QEA3009 QEA3009
6 Screw BPZ20P060FTC Not used Not used Not used Not used Not used 7 Polyethylene Bag CEG1160 CEG1160 CEG1160 Not used CEG1160 CEG1160 8 Handle QNC3021 QNC3021 QNC3021 Not used QNC3021 QNC3021 9 Screw Assy YEA5072 YEA5082 YEA5082 Not used YEA5082 YEA5082* 10 Polyethylene Bag CEG-127 CEG-127 CEG-127 Not used CEG-127 CEG-127
11 Screw CRZ50P090FTC Not used Not used Not used Not used Not used 12 Screw TRZ50P080FTC TRZ50P080FTC TRZ50P080FTC Not used TRZ50P080FTC TRZ50P080FTC 13 Protector QHP3016 QHP3016 QHP3016 Not used QHP3016 QHP3016
14 Case Assy Not used QXA3129 QXA3129 QXA3129 QXA3129 QXA312915 Remote Control
16 Bush Not used Not used Not used CNV3930 Not used Not used17 Screw Not used Not used Not used CBA1650 Not used Not used
18-1 Owner's Manual CRD4525 CRB3473 CRD4527 Not used CRD4527 CRD4527* 18-2 Warranty Card CRY1276 CRY1304 Not used Not used Not used CRY1250* 18-3 Service Network Not used CRY1305 Not used Not used Not used CRY1251
Part No. Language
CRD4525 English, French, Spanish(Espanol)
CRB3473 English
CRD4527 English, Spanish(Espanol), Portuguese(B), Traditional Chinese, Arabic, Persian
(2) CONTRAST TABLEDEH-3300UB/XSUC, DEH-3390UB/XNID, DEH-3350UB/XNES, DEH-3350UB/X1NEC, DEH-3350UB/XSES and DEH-3350UB/XNES1 are constructed the same except for the following:
Mark No. Description Part No.
1 Cord Assy See Contrast table (2)
2 Screw ASZ26P050FTC
3 Screw BSZ26P060FTC
4 Screw BSZ26P080FTC
5 Screw BSZ26P120FTC
6 Cable CDE9337
7 Tuner Amp Unit See Contrast table (2)
8 Screw BPZ26P080FTC
9 Screw BSZ26P060FTC
10 Screw BSZ26P120FTC
11 Holder See Contrast table (2)
12 Heat Sink QNR3002
> 13 Fuse(10 A) YEK5001
14 Detach Grille Assy See Contrast table (2)
15 Screw BPZ20P100FTC
16 Button(EJECT, SRC, BAND, LEFT) CAI3203
17 Button(LIST, RPT, UP, DOWN) CAI3204
18 Spring CBH2210
19 LCD(V1801) CAW1998
20 Holder See Contrast table (2)
21 Lighting Conductor QNV3022
22 Rubber Contact QNV3023
23 Connector YNV5192
24 Knob Unit CXE3692
25 Spring YBL5010
26 Grille Unit See Contrast table (2)
27 Grille Unit See Contrast table (2)
28 Door CAT2921
29 Button(RIGHT, -, 1-6) QAC3052
30 Button(DETACH) QAC3053
31 Cover QNS3125
32 CD Mechanism Module(S11.1) CXK5802
33 Panel Unit See Contrast table (2)
34 Cover See Contrast table (2)
35 Spring QBH3001
36 Panel See Contrast table (2)
37 Arm See Contrast table (2)
38 Button See Contrast table (2)
39 Case QNB3001
40 Holder QNC3020
41 Panel QNS3127
42 Remote Control Unit CXE3669
43 Cover CNS7068
44 Label See Contrast table (2)
45 Detach Grille Panel Assy See Contrast table (2)
26 Grille Unit Not used CXE3749 CXE3747 CXE3747 Not used CXE3747 27 Grille Unit CXE3744 Not used Not used Not used CXE3746 Not used 33 Panel Unit CXE3805 *QXA3261
37 Arm QNV3025 QNV3025 QNV3025 QNV3025 QNV3025 QNV302538 Button QNV3026 QNV3026 QNV3026 QNV3026 QNV3026 QNV302644 Label Not used CNN3533 Not used Not used Not used Not used45 Detach Grille
Panel AssyNot used Not used Not used CXE4037 Not used Not used
46 Cord Assy Not used Not used Not used QDP3014 Not used Not used
DEH-3300UB/XSUC 375 6 7 8
C
D
F
A
B
E
1 2 3 4
9.3 CD MECHANISM MODULE
A
CD
C
A
B
B
C
D
(A) : GEM1045
(B) : GEM1038
(C) : GEM1024
(D) : GEM1043
(C)
(C)
(A)
(A)
(D)
(D)
(A)
(A)
(D)
(A) (A)
(A)
(A)
(A)
(C)
(C)
(C)
(C)
(B)
(C)
(C)
DEH-3300UB/XSUC381 2 3 4
C
D
F
A
B
E
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LISTMark No. Description Part No.
1 .....
2 Screw BSZ20P040FTC
3 Screw(M2 x 4) CBA1835
4 Washer CBF1038
5 Spring CBH3010
6 Spring CBH2855
7 Spring CBH2856
8 Spring CBH2860
9 Screw BSZ26P060FTC
10 Spring CBH3011
11 Spring CBH3012
12 Spring CBH3014
13 Spring CBH3015
14 Spring CBH3016
15 Spring CBH3017
16 Spring CBH3086
17 Spring CBH3019
18 .....
19 Spring CBL1822
20 Pickup Unit(S10.5)(Service) CXX1942
21 Bracket CND4553
22 Arm CND4555
23 Bracket CND5709
24 Bracket CND5710
25 Lever CND5398
26 Sheet CNN2280
27 Rack CNV8342
28 Guide CNW1171
29 Roller CNW1172
30 Arm CNW2157
31 Arm CNW1174
32 Roller CNW1175
33 Lever CNW1176
34 Arm CNW1177
35 Arm CNW1178
36 Gear CNW1180
37 Gear CNW1181
38 .....
39 Gear CNW1183
40 Rack CNW1184
41 Gear CNW1185
42 Gear CNW1186
43 Gear CNW1187
44 Gear CNW1188
45 Clamper CNW1190
46 Arm CNW1192
47 Holder CNW1193
48 Holder CNW1194
49 Damper CNW1197
50 Damper CNW1198
51 Arm CNW1726
52 Motor Unit CXC4026
53 Screw Unit CXC8894
54 Arm Assy CXE3849
55 Washer CBF1037
56 Washer CBF1038
57 Arm CND5886
58 Collar CNV6906
59 Roller CNW1196
60 Gear Unit CXC8893
61 Washer YE15FTC
62 Chassis Unit CXE3818
63 Motor Unit CXE2273
64 Screw JFZ20P025FTC
65 Screw JGZ17P022FTC
66 Screw EBA1028
67 CD Core Unit (S11.1STD-DOUT) CWX3985
68 Chassis CNA3181
Mark No. Description Part No.
DEH-3300UB/XSUC 395 6 7 8
C
D
F
A
B
E
DP
DT
KY
DT
VC
K
VD
T
ILM
ILM
R85
1
4.7k
R811
2.2k
C85
1
GND
2 2
3 3
D
R809
8.2
R810
8.2
C234CCG1192-
C23
2
0.01
u/16
ND
C235
NM
TC
K
TM
S
TD
IR
619
C62
1
01u
/10
R61
8N
M
C62
0
0.1u
/10
X601S1603-A
22
33
DG
ND
5N
C6
VC
C7
VO
UT
L8
VO
UT
R9
AG
ND
10
VC
OM
11
ZE
RO
R/Z
ER
OA
12
ZE
RO
L/N
A
MD
28 29 30 31
PV
CC
432
TM
S77
TC
K78
AU
DIO
_X2
79A
UD
IO_X
180
PV
CC
681
VS
S7
C23
9
1000
p/50
VC
K
DP
DT
/TE
ST
DO
KY
DT
/TE
ST
DI
NC
/TE
ST
CLK
VD
T
934MHz
(DCH1201-A
1 2 3 4
10. SCHEMATIC DIAGRAM10.1 TUNER AMP UNIT (GUIDE PAGE)
A
A-aA-a A-b
A-a A-b
A-bA-a
Large sizeSCH diagram
Guide page
Detailed page
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".
ILMC2
ILMC1
DPDT2
KYDT2
ROT0_2
ILMB
ROT1_2
SWVD2
SYNC
VD
CO
NT
VDSENS
7.4V
AN
TP
W
SY
SP
W
VD
CO
NT
US
BC
TL
SY
NC
FLG
VS
T
DA
TA
CD
DA
TA
IN
CD
LRC
KIN
CD
SC
KIN
CD_SDA
CD_SCL
CPPW
CDRST
CDSRQ
CDSTBY
CDWAIT
FLPILM
SWVDD5
ILMCLR1
ILMCLR2
KEYD
CD
ST
BY
CD
RS
T
CD
WA
IT
DA
TA
LRC
K
ML
MC
MD
SC
K
SC
K
ML
CD
SK
IP
TE
LIN
MC
MD
CPRST
CP_SCL
CP_SDA
ILMPW
TUNR
TUNL
ASENS
SSENS
BSENS
CD
_SD
A
CD
_SC
L
CD
SR
Q
DM2
DP2
AUXL2
SRC2
AUXR2
AUXG2
ROT1
ROT0
RGBDT
RG
BD
T
SRC2
KYDT2
ROT0_2
ROT1_2
FLG
USBCTL
VBUS
CPRST
DPDT2
ILMC1
ILMC2
MU
TE
BC
K
LRC
K
BC
K
DM2
DP2
AUXL2
AUXR2
SWVD2
AUXG2
ILMB
CD
SC
KIN
CD
LRC
KIN
CD
DA
TA
IN
CD
SK
IP
CP_SDA
CPPW
CP_SCL
R50
1
470
R69
1
2.2k
R817
NMR80
3
NM
R50
3
6.8k
R816 NM
R812 2.2k
R813 2.2k
R807 2.2k
R806 2.2k
GND
DGND
SWVD
SRC
AUXR
AUXL
ROT1
ROT0
KYDT
DPDT
GND
C50
2
NM
US5V
DM
DP
GND
FLG
USBCTL
SYNC
ICLR1
NMS69
11
2
GND
DS
EN
S
FLPILM
C80
90.
1u/1
6
C80
5N
M
C80
70.
1u/1
6
C80
6N
M
EJECT
ICLR2
D80
1D
Z2S
068C
D80
2D
Z2S
068C
D80
4D
Z2S
068C
D80
5D
Z2S
068C
D80
3D
Z2S
068C
C80
80.
1u/1
6
C803
NM
CN801
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
C81
022
0p/5
0
C81
122
0p/5
0
R50
4
10k
R50
2
47k
R814 NM
R815 NM
R801 100
R802 100
AUXG
DSENS1
R60
3
100k
R60
2
47k
IC501
BD2226G
VIN1
GND2
EN3
/OC4
5VOUT
C50
11u
/10
GND
C50
4
1u/1
0
ILMG
GND
C80
1
NM
GND
GND GNDGND
C802
NM
L802CTF1713-A
11
44
R80
8
8.2k
GN
G22
0u/6
.3
C50
3
GND
USB5VL501
CTH1475-A
GND
D50
1R
B16
0L-4
0
BD9008F
IC502
PVIN1
SW2
FB3
INV4 5
EN/SYNC
6RT
7GND
8VIN
C50
8
22p/
50
R50
5
18k
C50
6
0.01
5u/1
6
R506
51k
R507
NM
GND
D502
CRG03
C50
5
CE
JQ22
1M16
-P25
C50
7 NM
GND
L551
LCTC4R7K1608-T
R55
1
47k
341S2162IC551
NC
11
MO
DE
1/S
PI_
nSS
2N
C2
3nR
ES
ET
4V
CC
5
NC3
6
NC47
NC58 NC69 NC7
10 VS
S
11
I2C
_SC
L/S
PI_
SIM
O
12
I2C
_SD
A/S
PI_
SO
MI
13
MO
DE
0/S
PI_
CLK
14
NC
8
15
NC9
16
NC10
17
NC11 18NC12 19NC13
20
LSA1576UB(QRS)Q551
R557 4.7k
R556 2.7k
C55
1
0.1u
/10
R552 10k
R558 4.7k
R560 100
R559 100
R553 10k
C552
0.1u/10
GND
R50
8
10k
JA401CKX1098-A
12
3
GND
TUNGND
M2R6TP_GNDKN401
R753
820
R754
NM
C75
1
CC
G11
92-A
R75
1
47k
C75
40.
1u/1
0
R75
2
10k
D75
1
RK
Z8.
2KG
(B2)
Q7512SD2396(K)
GND
C75
3N
M
NM
C75
2
VDCONT
VD2
VKN1192-ACN701
12345678910111213141516
RE
SE
T
SD
A
SK
IP
CD
SR
Q
BC
LK
DA
TA
LRC
K
SC
L
DG
ND
1
VD
D4
CD
ST
BY
PG
ND
WA
IT
R71
622
0 GND
C704
NM
C706
NM
R717
100k
R71
315
0
R71
415
0
R71
515
0
GND
C705
NM
GND
VD1
R70
722
0
R70
822
0
R70
910
0
R71
022
0
R71
110
0
R71
21k
R701
47kR702
100k
R703
100kC701
0.01u/16
L701 NM
C702
NM
C703
NMGND
IC671
A : PEA012A8B~F : PEA011A8
CE#1
SO2
WP#3
VSS45
SI
6SCK
7HOLD#
8VDD
R671 47k
C671 0.1u/10GND
R67
2
47k
C60
4
0.1u
/10
C60
6
0.1u
/10
R60
6
47k
R60
7
47k
R60
8
47k
RA
M_M
ON
C60
8
0.1u
/10
C61
0
0.1u
/10
R60
447
k
2 14 365 87
R60
1
10k
D60
1R
B55
1V-3
0
R61
0
2.2k
C61
4
NM
TE
ST
INR
615
100k
C61
6
0.1u
/10
C61
80.
1u/1
0
R61
2
47k
TE
ST
CK
C61
9
0.1u
/10
CS
11
R61
722
0
R61
6N
M
R61
310
0
R61
110
0
R60
910
0
C61
20.
1u/1
0
C60
9
0.1u
/10
C61
1N
M
C61
3N
M
C61
5N
M
C61
7
10p/
50
C60
7
0.1u
/10
C60
5
0.1u
/10
C602 0.1u/10
C603
0.1u/10
C601
0.1u/10
RGBDT
IC23
1
BC
K1
DA
TA
2
LRC
K3 4
1314
MC
15
ML
16
SC
K
M2R6TP_GNDKN601
GND
R61
4N
M
R605
NM
NMCN802
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
TE
LIN
1
RO
M
IC401
TDA7706
FMPINDRV
1
FMPINDDEC
2
FMMIXDEC
3
FMMIXIN2
4
FMMIXIN1
5
GNDRF6
TCAM7
VCCRF8
CK_SEL9
GNDVCO10
LFREF11
LF112
VCCVCO13
TCAM214
PINDDEC15
PINDIN16
LNA
IN2
21
LNA
OU
T2
22
LNA
DE
C2
23
AM
MIX
IN1
24
AM
MIX
IN2
25
GN
DS
LIN
K26
VD
IG27
VC
CR
EG
1V2
28
RE
G1V
229
VR
EG
3V3
30R
ST
N31
RD
SIN
T
32
I2CSDA
33
I2CSCL
34
VDD3V3
35
GND3V3
36
GPIO837
GPIO7 38GPIO6
39GPIO5
40GPIO4
41GPIO3
42GPIO2
43GPIO1
44GPIO0
45GND1V2
46VDD_CORE
47TEST
48
OS
CIN
52
OS
CO
UT
53G
ND
-RE
F54
VR
EF
DE
C55
GN
D-A
DC
_DA
C56
DA
CO
UT
L57
DA
CO
UT
R58
VC
C-A
DC
_DA
C59
VC
C-P
LL60
GN
D-P
LL61
PLL
TE
ST
62T
CF
M63
TV
DA
C64
LNA
OU
T
20LN
AD
EC
19
LNA
IN
18
GN
DLN
A
17
VC
C-R
EF
51V
DD
IO1V
2
50
VD
DP
LL1V
2
49
P40
1
IMS
A-6
802-
01Y
900
C401
33p/50
L401
0.15
u
C40
2
6p/5
0
C40
30.
01u/
16
D40
1
KP
2311
E
D40
2
KP
2311
EC
406
0.01
u/16
L4040.27u
R40
1
220
R40
2
750
C413
0.01u/16
GND
C40
90.
01u/
16
C414
1u/10
GND
GND
L414 NM
L413 NM
L410
NM
C40
4
0.1u
/10
C407
0.1u/10
C410
0.01u/16
C40
5
0.1u
/10
C411 0.01u/16GND
C412CCG1192-A
GND
GND
C408
L406
R403
R40
5
1M
C415
0.01u/16
GND
C41
8C
CG
1192
-A C42
0
0.1u
/10
C42
2
0.1u
/10
C42
3
0.01
u/16
C42
1R
407
33
R40
6
GND
L409
GND
R40
8
C42
7
GND
C43
4
NM
R410
8.2
C43
0
0.47
u/10
C43
3N
M
C43
8
C43
6
NM
C43
9
GND
C440
0.1u/10
GND
GND
C442
NM
C441CCG1205-A
C43
7
0.1u
/10
GND
C43
2N
M
C43
5N
M
C43
10.
1u/1
0
C42
6
0.1u
/10
R40
9
NM
C42
8
9p/5
0
C42
9
9p/5
0
GND
GND
C424 4700p/25
C425 4700p/25
GND
C41
9
1u/1
0
C41
7
0.1u
/10
C41
6
0.22
u/16
X401
CSS1806-AX1
1GND1
2
GND24 X2 3
R7044.7k
2
1
4
36
5
8
7
L417
C44
4
C443
R41
31M
C445
0.022u/16
C448
NM
C44
9N
M
R41
4
NM
R41
5
NM
R41
6
NM
R417
NM
C446
NM
L418
R41
8
NM
R41
910
k
R42
010
k
R81
8
NM
ILM
USGND
CSEN
R561
NM
C82
022
0p/5
0
PC
L
C450
NM
R421
SI
SCK
SO
CE
C44
7
1000
p/50
LFREF
LF1
RN4983
Q752
E1 1
B1 2
C2 3 E24
5 B2
6 C1
R63
4
NM
R819
0
D80
8
NM
D80
7N
M
D80
6N
M
C45
1
R412
8.2
R5S7266ZD144FP
IC601P
VC
C1
1 2
VS
S1
3 4
VC
C1
5 6 7 8 9
10 11 12
PV
CC
213 14
VS
S2
15 16
VC
C2
17 18 19 20 21 22
PV
CC
323
VS
S3
24
VC
C3
25 26 2782
VC
C4
83848586878889P
VC
C7
9091V
SS
89293
VC
C5
949596979899100
101
PV
CC
810
2
103
VS
S9
104
105
VC
C6
106
107
108
109
110
111
112
113
114
115
116
PVCC9117
118
VSS10119
120
121
122
123
124
125
PVCC10126
VSS11127
128
129
130
131
132
133
PVCC11134
135
VSS12136
137
138
139
140
141
142
143
144
L419
NM
R820 100
R821 22k
R822 22k
D80
9D
Z2S
068C
D81
0D
Z2S
068C
L416
L402
CTF1786-A
L403
CTF1786-A
L407
CT
F17
86-A
L408
CT
F17
86-A
L412
NM
L411
L415
CT
F17
86-A
GND
C509
1u/16
C81
21u
/16
C454
NM
C45
2
C45
3
NM
GND
GND
R427
1k
C707
1000p/50C708
1u/10
GND
R71
8N
M
R71
9N
MR
720
NM
L671CTF1786-A
R428
R429 NM
C709
NMC710
NM
L405
R562
NM
R823
2.2k
C81
8
1000
p/50
GND
C45
5
GND
C45
6
GND
L420R
430
NM
B.UP
SYSTEM MICRO
GRILL
DGND
KYDT
DPDT
ROT1
ROT0
ILMCLR2
ILMCLR1
EJECT
CSENS
SOURCE
AUX R
AUXGND
AUX L
FLAPILM
SW5V
DP
USB5V
DM
ILMGND
USBGND
ILM+B
USBGND
DSENS
KYDT
USBGND
SOURCE
AUXGND
DGND
SW5V
DP
DSENS
DPDT
DM
ILMGND
ILM+B
ROT0
ROT1
AUXR
AUXL
USB5V
NM
ipod CP
CD
FLASH ROM
MECHA VD
10U
/10
USB&USB5V
P
VDD3.3V
USB ILMD
D USBILM
DAC
D
RF
TUNER
LRC
K
GN
D
GN
D
VD
D
PG
ND
WA
IT
VD
SD
A
BC
LK
/CD
ST
BY
DA
TA
VD
SC
L
/CD
SR
Q
RE
SE
T
SK
IP
TU
NP
DICD_SDA
NC
VD
CO
NT
MU
TE
NC
DA
CB
DA
TA
CDWAIT
CD_SCL
TU
NP
CE
1
PC
L
CA
DA
TA
IN
DA
CD
AT
A
NC
ILMCLR1
CD
SC
KIN
DSENS
SY
NC
ILMPW
VS
T
CDSRQ
CPPWR
MO
SI
/SS
L
RGBDT
CDSTBY
DA
CS
CK
TU
NP
DO
FLPILM
CP_SCL
US
BC
TL
CP_SDA
CD
SK
IP
NC
NC
ASENS
CD
LRC
KIN
/US
BF
LG
RO
M
DACCST
UN
PC
E2
SSENS
SY
SP
W
CDRST
/RD
SLK
EJE
CT
BSENS
RA
M_M
ON
TE
SIN
DA
CLR
CK
MIS
O
CPRST
SWVDD
AU
DIO
_XO
UT
RS
PC
K
TE
LIN
AN
TP
W
ROT1
DA
CB
SC
K
ILMCLR2
KEYD
ROT0
NC
VDD3.3V
RF
RF
RF
A
RF
RF
RF
RF
RF
A
D
D
D
D
A
A
1/4W
RF
RGBCK/ILMCLR1
RGBST/ILMCLR2
RGBDT/USBGND
TUNSDATUNSCL
NC
RD
S_I
NT
1/4W
*2
SW5V
36.48MHz
16.
CKS6288-A
(DC
H12
01-A
)
(DC
H12
01-A
)
(DCH1201-A)
(CCG1218-A)
D
*2
(CSS1805-A-T)
(CTH1420-A-TLB)
*2
*2
NM
NM
NM
NM
CTF1389 22uH
NM 1.5k
470
100p
47uH
680
82p
NM
0
NM
NM
0
NM
*2
B - FAC443 0.01uNMC451C452
NMNM
3p1000p
C455 NM10pL420 NM68n
EVOL 201 - 230
RCA 251 - 300
AMP 301 - 400
TUNER 401 - 500
USB&USB5V 501 - 550
UCOM 601 - 650
CD MECHA 701 - 750
GRILL 801 - 850
PW CONNECT 901 - 910
IC REG 911 - 930
ASENS 931 - 940
W.REM 961 - 970
A.ANT 951 - 960
DAC 231 - 250
I-POD 551 - 600
MECHA VD 751 - 800
FLPILM 891 - 900
RESET 651 - 670
TELIN 941 - 950
SWVDD5 851 - 870
FLASH ROM 671 - 690
DSENS 691 - 700
ILMPW 871 - 890
REFERENCE AREA MAP
C CN701
BCN1821
The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.
F.ACT: Applying positive voltage to FOP, the lens approaches DISC.
T.ACT: Applying positive voltage to TOP, the lens moves outer circumference of DISC.
CLCONT
MOTOR DRIVER LOGIC TABLE
LOEJ
CONT
LOAD EJ PLAY OFF
HH L L
-
L
-
H
L
L
H
L
VDD
GND
PGND
VD
REFO
REFO
RE
FO
*
(1/1
0SR
,160
8)
*
*
**
*
* *
*
*
A
D
I
P
C209 C238 C240C306 C307
R243 R246R101 R102 R103
C104
1608:PARTS
2125:PARTS
R606
Parts with Polarity
IC201 IC301D101Q101 Q102 Q201
C205 C301 C308
*
D
A
I
P
*
CIRCUIT No.
(1/1
0W)
C708
Digital Out model only
Analog Out model only
IIC-BUS model only
P-BUS model only
HOME
8EJ
DSCSNS
SWITCHES:CD CORE UNIT S901:HOME SWITCH.........ON-OFF S903:DSCSNS SWITCH.....ON-OFF S905:8EJ SWITCH..............ON-OFF
The underlined indicates the switch position.
F
T
T
F
F
T
T
F
F
T
T
F
F
T
F
T
F
T
C
C
S
S
S
C
C
S
C
S
1
2
3
9
a
7
84
5
f
c
d
e
DEH-3300UB/XSUC481 2 3 4
C
D
F
A
B
E
ATEST
ASY
EFM
CN70CKS5766-
NM
A.Vdd176
A.GND177
RFI78
AGCO79
C3T80
AGCI81
RFO82
EQ283
EQ184
RF2-85
RF-86
A.GND287
A.Vdd288
A89
B90
F91
E92
REFOU93
FE-94
FEO95
ADCIN96
TE-97
TEO98
TE299
TEC00
BLE
OFF
L
-
L
*
5 6 7 8
C
P
A A
A
D
I
P P
A
A
P
I
D
D
D
D
D
D
P
SCL
MD
SD
LOEJ
SK
IP
/CD
SR
Q
AD
EN
A
CLCONT
TE
MP
VD
SE
NS
CONT
RESET
ADENA
TEMP
/CDSTBY
/WAIT
VPP
ICECK
DSCSNS
8SNS
SC
K
ICE
CK
SC
K
FD
HOME
TD
BCLK
LRCK
DATA
SDA
VP
P
PU
EN
CVDD
CV
DD
SKIP
/CDSRQ
VDSENS
/CDSTBY
RE
SE
T
/WA
IT
LRCK
DATA
SCL
SDA
DATA
/WAIT
BCLK
LRCK
BCLK
RESET
VDD
VD
PGND
GN
D
CD
SR
Q
CD
ST
BY
SC
L
SK
IP
SD
A
RE
SE
T
LRC
K
BC
LK
DA
TA
X201CSS1603-A
1
2
3
PUEN
TESTIN
R24
6
NM
(160
8)
VDSENS
TEMP
C20
30.
1u/1
0
C207
NM
C210
0.1u/10
C211
0.1u/10
C21
2
0.1u
/10
C21
5
0.1u
/10
C206
NM
C23
5
NM
C71
010
00p/
50
C232
1000p/50
C231
1000p/50
R264
1k
R254
100k
R253
NM
R26
0
10k
R23
5
10k
R23
6
10k
R263
4.7k
R262
4.7k
NMTH201
NMQ201
RS
T
INT
Q A0
ST
B
SC
K
SO
SI
ICE
MD
VP
P
CV
DD
ICECK
C16
M
MO
NI0
MO
NI1
MO
NI2
VD
2
VD
1V
DD
1
GN
D1
GN
D2
GN
D3
R242
NM
R245 100k
C233
0.01u/16
R237
220
R240
47k
C70
5
NM
VD
D2
2A
1V
DD
2
3C
VD
D4
5IC
EC
K6
SO
7S
CK
8S
I
9V
PP
10G
ND
R29
6
0
C20
4N
M
C70
7
NM
C70
2
NM
C209
0.1u/16 (1608)
C23
8N
M(1
608)
C24
0N
M(1
608)
C70
8
NM
(160
8)
R283
0 C281
NM
C282
NM
NM
C205
R29
4
470
C70
1
NMC70
3
NM
WA
IT
C283
NM
C284
NM
R243
NM(1608)
PG
ND
1
PG
ND
2
ADENA
C29
9N
M
R706
220R702
100
R701
100
R297
NM
C601
NM
C602
NM
R723
NM
R721
NM
R70
7
NM
R606
NM (1608)
R722
0
R709
0
R708
0
R29
9
0
C21
4
0.04
7u/1
0
R215
39k
R21
4
10k
C21
3
3300
p/50
CKS6146-ACN701
1 VD
2 VD
3 /CDSRQ
4 /CDSTBY
5 SCL
6 SKIP
7 SDA
8 RESET
9 VDD
10 GND
11 DATA
12 BCLK
13 LRCK
14 GND
15 PGND
16 WAIT
AAGND1 AAGND2
R225
0
R292 0
R293
0
R71
0
NM
R71
1
NM
IC201
PE5756A
LD1
PD
2
/RS
T3
INT
Q(I
NT
1)4
A0
5
/ST
B6
/SC
K7
SO
8
SI
9
D.V
dd10
D.G
ND
11
RE
G16
12
RE
GS
13
DA
.Vdd
114
RO
UT
15
DA
.GN
D1
16
RE
GC
17
DA
.GN
D18
LOU
T19
DA
.Vdd
20
ICE
MD
21
X.V
dd22
/XT
AL
23
X.G
ND
24
XT
AL
25
Vpp26
C.Vdd27
C.GND28
RESET29
IO.GND130
IO.Vdd131
ICECK32
/CDSTBY33
34HOME
3512SNS
368SNS
37DSCSNS
38CONT
39CLCONT
40LOEJ
41PA7
42DOUT
43SCKO
44LRCK
45TX/EMPH
46/WAIT
47SCL
48SDA
49PC3
50
/TE
ST
IN51
/CD
SR
Q52
SK
IP5354
/AD
EN
A555657
TE
MP
58M
onito
r059
Mon
itor1
60M
onito
r261
Mon
itor3
62S
D2
63IO
.GN
D2
64IO
.Vdd
265
FD
66T
D67
SD
68M
D69
TE
ST
70A
D.G
ND
71A
D.V
dd72
EF
M73
AS
Y74
AT
ES
T75
T
R232
0
BS
CK
0
LRC
K0
EJSW
R60
1
NM
R60
2
NM
R603
NM
R604
NM
R281 56
R282
56
R291
56
NO MOUNT PARTS (NM)*
Land for manual soldering
GND
GND
GND
3.3V
7.5V
7.5V
I/O
VDD
GND
GND
EJSW
VD
CO
NT
VD
SE
NS
*
*
*
*
*
*
*
**
*
*
*
*
*
*
*
(RO
UT
)
(LO
UT
)
(AG
ND
)
*
**
R294MaskFlash
4700
MaskR232
Flash 10k0
PU
EN
* *
* *
*
Mask FlashR281R282R291
565656
22
2222
16.934MHz
ACN701
C CD CORE UNIT(S11.1STD-DOUT)
FSIGNAL LINEFOCUS SERVO LINETRACKING SERVO LINECARRIAGE SERVO LINESPINDLE SERVO LINE
T
C
S
S T FC
6
i h g
b
DEH-3300UB/XSUC 495 6 7 8
C
D
F
A
B
E
1 2 3 4
10.4 WAVEFORMS
- CD CORE UNIT Note : 1. The encircled numbers denote measuring points in the circuit diagram.2. Reference voltage REFO1(1.65 V)
500 ms/div5 V/div5 V/div5 V/div10 V/div
1DSCSNS5CLCONT4LOEJ6VD
5 V/div5 V/div5 V/div5 V/div
1DSCSNS28SNS4LOEJ3HOME
5 V/div5 V/div5 V/div5 V/div
500 ms/div1DSCSNS28SNS4LOEJ3HOME
500 mV/div500 mV/div
200 ms/divcTEdFE
200 mV/div2 V/div2 V/div
500 ms/divaFINbRFOK(MONI_3)7SIN
1 V/div500 mV/div500 mV/div
2 s/div
500 ms/div
7SIN8CIN9TIN
2 V/div500 mV/div
5 s/diveMDX7SIN
2 V/div500 mV/div
50 ms/diveMDX7SIN
500 mV/div500 mV/div500 mV/div500 mV/div
20 ms/divdFEaFINcTE9TIN
1 V/div500 mV/div500 mV/div
500 s/divfRFAGCcTE9TIN
500 mV/div500 mV/div
2 ms/div cTEfRFAGC
500 mV/div500 mV/div
200 ms/divaFINdFE
Source On setup operation12 cm CD-DA Source On setup operation
CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation(Wider)
Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3)
12 cm CD-DA setup operation after loading
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation
Ref.:GND
Mode:Normal
Ref.:GND
Mode:Normal
Ref.:GND
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:TEST
Ref.:REFO
Mode:TEST
Ref.:REFO
Mode:TEST
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:Normal
DEH-3300UB/XSUC501 2 3 4
C
D
F
A
B
E
5 6 7 8
2 V/div2 V/div2 V/div
10 s/divgLRCKhBCLKiDATA
1 V/div1 V/div500 mV/div2 V/div
200 ms/divfRFAGCcTE8CIN7SIN
1 V/div500 mV/div500 mV/div
2 ms/divfRFAGCcTE9TIN
5 V/div5 V/div5 V/div5 V/div
500 ms/div1DSCSNS28SNS4LOEJ3HOME
5 V/div5 V/div5 V/div5 V/div
500 ms/div1DSCSNS28SNS4LOEJ3HOME
5 V/div5 V/div5 V/div
500 ms/div1DSCSNS5CLCONT4LOEJ
1 V/div1 V/div1 V/div1 V/div
500 s/divfRFAGC9TINcTEaFIN
12 cm CD Eject operation8 cm CD Eject operation
Black Dot (800 m) during play
12 cm CD Eject operation
32 Tracks Jump waveform (Zoom of 100 Track Jump waveform) Search operation(Outter to Inner) Digital Out waveform
Ref.:REFO
Mode:TEST
Ref.:GND
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:REFO
Mode:Normal
Ref.:GND
Mode:Normal
Ref.:AGND
Mode:Normal
DEH-3300UB/XSUC 515 6 7 8
C
D
F
A
B
E
15
2
R30R30
R30
R33
2R
334
C30
2C
306
C31
0C
311
C31
5
C33
2
C33
4
0
P>
1 2 3 4
11. PCB CONNECTION DIAGRAM11.1 TUNER AMP UNIT
A
A TUNER AMP UNIT
CapacitorConnector
P.C.Board Chip PartSIDE B
SIDE A
NOTE FOR PCB DIAGRAMS1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram.2.Viewpoint of PCB diagrams
1
1
1 5
10
1
5
1
1
1
156
R25
1
R252
R25
3
R25
4
R25
5
R25
6
R25
7
R25
8
R25
9
JA251
C251
C252
C253
C254
C25
5
C25
6
C25
7
C25
8
C259
C260
C261
L501
R501
R502R503
R50
4
R50
5
R506
R507
R33
1R
333
C30
1
C30
3
C30
4
C30
5
C30
7
C30
8
C50
1
C502
C503
C50
4
C505
C50
6
C313
C50
7
C50
8
C31
4
C50
9
C316
C31
7
C33
1
C33
3
P251
R96
1
R96
2
JA961
D50
1
D502
IC301
C96
1
C96
2
IC501
IC502
Q251
Q252
10 20 30 40 50 60 70 8X
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Y
1
2
2
34
3
FRONT
W. REM
C CN701
PRE OUT
DEH-3300UB/XSUC521 2 3 4
C
D
F
A
B
E
10
R33
1R
333
C30
1
C30
3
C30
5
C30
7
C33
1
C33
3
IC
FRO
5 6 7 8
A
SIDE A
1
1
1
1
1
E
E
E
E
E
E
E
E
E
E
E
15
20
25
01 5 1
1 5
10
1
5
1
1 5 10
1520
1
5
1 5
1015
1 510 15 20 25 30 35
40 45 50 55 60 65 70
7580
8590
95100
105
110115120125130135140
1 5 10 15
20 25 30
35 40 45
50
55
601 5
10
15
20
1
1
1
1
1
1 5150201
101
510
15
1 5 10 15 20
1
1
1
1
1
1
R401
D941
R402
R403
R40
5
D751
R406R407
R408
R409
R60
1
R602
R60
3
R41
0
R604
R60
5
D95
1
R41
2
R606
D95
2
R413
R607
R414
R608
R415
R609
R41
6
R417R418
R41
9
R80
1
IC551
R80
2
R80
3
R610
L851
R611
R612
R80
6
R613
R80
7
R420
R614
R80
8
R42
1
R80
9
R61
5
JA401
R616R617
R618
R619
R23
1R
232
R427
R428
R81
0
R42
9
R81
1
Q871
R81
2
Q872
Q873
R81
3
R81
4
R62
0
R621
R81
5
R622
R816
R817
R62
3
R818
R624
R819
R625
L671
C20
1
IC951
R62
6
C202
R62
7
C20
3
R628
C204
R629
CN801
C20
5
CN802
C20
6
C20
7
R82
0
C20
8
R821
C20
9
R822
R823
R630
R63
1
C401
R632
C402
R63
3
C403
R634
C21
0
C40
4C21
1
C40
5
R636
C21
2
C406
C213
R63
7
C40
7
C214
R638
C408C21
5
R639
C409
C60
1
Q891
C602
Q892
C603
R640
C410
C604
X401
C41
1
C605
C41
2
C606
C413
C607
C41
4
C608
C41
5
C609
C41
6
C41
7C418
C419
C801
C802
C803
C610
C61
1
C80
5
X601
C61
2
X602
C806
C61
3
C80
7
C420
C614
C808
C421
C61
5
C80
9
R651
C422
C616
C423
C617
C424
C618
C425
C619
C231
C426
C232
C427
C233
C428
C234
C81
0
C429
C235
C81
1
C812
C237C620
C23
8
C23
9
R851
C62
1
C622
C623
C817
C818
C43
0
C624
C431
C62
5
C432
C62
6
C433
C627
C434
C62
8
C435
C629
C436
C437
C82
0
C43
8C
439
C630
C631
C632C633
C440
C63
4
C441
C63
5
R671
C442
C63
6
R672
C443
C63
7
C444
C638
C445 C446
C447
C448
C449
R87
1
R872
R873
C45
0
R874
C451
C452
C45
3
C454
C45
5
C45
6
Q301
C65
1C652
D401
R691
D402
C851
C852
R891
D60
1
R892
D602
R893
IC201
D80
1
D80
2
D80
3
D80
4D
805
C671
D80
6
D80
7
D808
D80
9
IC401
L701
D81
0
C87
1
C87
2
IC601
L901
IC801
IC231
Q351
Q931
Q551
R301R302R303
R304
D651
Q941
S691
Q751
Q752
L551
R508
Q951Q952 Q953
R701
L941
R702
R70
3
R704
R707
R708R709
IC651
R710R711R712
R713R714R715
R716R717
R718R719
R33
2R
334
R911
CN701
R91
2
R720
C30
2
C30
4
P401
C30
6
C30
8
C309
IC671
KN401
C31
0C
311
C31
2
C31
5
R351
R35
2
R353C318C319
C70
1
KN601
R93
1
R932
C70
2
C70
3
R93
3R
934
C70
4C
705
C70
6
C70
7
C320
C70
8
C321
C709
R55
1
R55
2R
553
C901
R55
6
R557
C710
R558
R55
9
R941
R94
2
R94
3
R751 R752
R75
3
R56
0
R754
R561
R56
2
C33
2
C33
4
C911C912
C913
C914
R951
C915
R952
C91
6
C91
7
C918
C919
C920
C921
C922
C923
C924C925
C926
C927
C35
1
C93
1
C55
1
C552
D30
1
D30
2
C75
1
C752
C75
3
C754
L201
C95
1
C952
L401L402L403
L404L405
L406
L407
L408L409
301
L601
D90
1
L602
D90
2
L410
L411
L412
L413
L414
L415
L416
L417
L418
L419
L802
D91
1
D91
2
L420
L231
D931
IC912
R201
R205
R20
6R
207
80 90 100 110 120 130 140 150 160
15
16
5 9
6
1
2 10
13
14 18
17
JA901
NT
POWER SUPPLY
ANTENNA
B CN1821
P 251 (A,7,129) Fuse 3 A CEK1286>
FUS
E
>
DEH-3300UB/XSUC 535 6 7 8
C
D
F
A
B
E
90
1
1 2 3 4
A
A TUNER AMP UNIT
100110120130140150160
1
1
1
1
TESTIN
PCL
DEH-3300UB/XSUC541 2 3 4
C
D
F
A
B
E
100
1
1
1
N
PCL
5 6 7 8
A
SIDE B
102030405060708090 X
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Y
1
1
1
DEH-3300UB/XSUC 555 6 7 8
C
D
F
A
B
E
1 2 3 4
11.2 KEYBOARD UNIT
B
SIDE AB KEYBOARD UNIT
1
1
5
1
40
35
30
25
20
15
10
5
1
CN
1901
CN
1911
D19
13
IC18
02
R18
23
C18
52
C18
53 C18
54
C1855
C18
56
C18
57
C1858
C18
59
C18
60
C1861
C18
62
C1863
C18
65
C18
66
C18
67
C18
68S
1821
S18
22
S18
23
S18
25 S18
26
S18
27S
1828
D18
51
S18
29
D18
52
D18
53
D1854
D18
55
D1856
D18
57
D1858
S18
30
D18
59
S18
31
S18
32
S18
33S
1834
S18
35S
1836
S18
37S
1838
D1860
S18
39
D1861
D1862
D1863
D1864
D1865
D18
66
D1867
D18
68S
1840
D18
69S
1841
S18
42
S18
43
S18
45
D18
70
D18
71
D18
72
D1873
D1874
D18
75
D1876
D1877
D1878
D1879
D1880
D1881
D1882
D1883
R18
83
V18
01S
1824
1020
3040
5060
7080
9010
011
012
013
014
015
0X
40 30 20 10
0
Y
160
LCD
US
B
AU
X6
54
32
1C
LOC
K
UP
RIG
HT
DO
WN
LIS
T
LEF
T
EJE
CT S
RC
BA
ND
DIS
P
MU
LTI-
CO
NT
RO
L
DEH-3300UB/XSUC561 2 3 4
C
D
F
A
B
E
5 6 7 8
B
SIDE BB KEYBOARD UNIT
1020
3040
5060
7080
90100
110120
130140
150
X
40302010
0Y
160
1
1
51
1 5 10 15
20 25 30
35
4
0
4
5
50 55 60
1
1
515
1
2010
C1901
X1801
C1902
C1903
R1901
R1902
D1911
D1912
L1801
C1801
C1802
CN
1821
D1801
D1802
R1801
R1802
R1803
R1804
R1805
R1806
IC1801
R1821
R1822
R1824
R1825
R1826
Q1851
L1911
C1864
R1851
R1852
R1853
R1854
R1855
R1856R1858
R1860R1862
R1864
R1866
R1868
R1871
R1872
R1873
R1874
R1875
R1880
R1881R1882
R1884
R1885
R1888
R1889
R1890
R1891
R1892
R1893
R1894
R1895
R1896
R1897
R1898
R1899
VA1901VA1902
VA1903
VA
1904
A CN801
1
1
DEH-3300UB/XSUC 575 6 7 8
C
D
F
A
B
E
1 2 3 4
11.3 CD CORE UNIT (S11.1STD-DOUT)
C
SIDE AC CD CORE UNIT (S11.1STD-DOUT)
1 510 15 20 25
30 35 40 45 50
55
60
6
5
70
75
80 85 90 95 100
1 5 10 15
1 5 10 15
1 5
10
1
0151
152025
29
30
1
R214
R215
R216
R21
7
R21
8
R225
R229
R232
R23
5
R23
6
C203
C204
TH201
C207
C209
R246
C210
X201
C211
C212
C213
C214
C215
C216C21
7
C21
8
C219 C221C222C223
C224
C225
R26
2
R26
3
C22
8
R264
C235
C238
C240
R281
R282
R294
IC201C299 R305
R306
R307
R308
CN101
R707
R708
R709
R710
C102
CN701
CN702
C304C305
C306
C307
C701
C702
S901
D101
IC301
10 20 30 40 50 60 70X
60
50
40
30
20
10
0
Y A CN701
PICKUP UNIT(P10.5)(SERVICE)
F
E REFO1 M1SPINDLEMOTOR
M2LOADING/CARRIAGE
MOTORHOME
DEH-3300UB/XSUC581 2 3 4
C
D
F
A
B
E
5 6 7 8
C
SIDE BC CD CORE UNIT (S11.1STD-DOUT)
70 60 50 40 30 20 10X
60
50
40
30
20
10
0
Y
E
E
1
1
E
R601
R602
R603
R604R606
R237
R240
C205
C206
R242
R243
R245
R253R254
C601
C602
C220
R260
C229
C231
C232
C233
C236
C239
R283
R291R292
R293
Q101
Q102
R296
R297
R299
C281
C282
C283
C284
R101
R102
R103
R106
R108
R109
R701
R702
R706
R711
C101
C104
R721R722
R723
C301
C110C111
C308
C703 C705
C707
C708
C710
S903
S905
Q201
8EJ
DSCSNS
DEH-3300UB/XSUC 595 6 7 8
C
D
F
A
B
E
1 2 3 4
12. ELECTRICAL PARTS LISTNOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No.
A:DEH-3300UB/XSUC
B:DEH-3390UB/XNID
C:DEH-3350UB/XNES
D:DEH-3350UB/X1NEC
E:DEH-3350UB/XSES
F:DEH-3350UB/XNES1
Unit Number : CWN5477(A)
: CWN5478(B,C,D,E,F)
Unit Name : Tuner Amp Unit
Unit Number :
Unit Name : Keyboard Unit
Unit Number : CWX3985
Unit Name : CD Core Unit(S11.1STD-DOUT)
AUnit Number : CWN5477(A)
: CWN5478(B,C,D,E,F)Unit Name : Tuner Amp Unit
MISCELLANEOUS
IC 201 (A,98,112) IC PML022AIC 231 (A,137,60) D/A Converter PCM1753DBQIC 301 (A,78,142) IC PAL007EIC 401 (A,150,91) IC TDA7706IC 501 (A,41,122) IC BD2226G
IC 502 (A,20,114) IC BD9008FIC 551 (A,120,90) IC 341S2162IC 601 (A,113,67) IC R5S7266ZD144FPIC 651 (A,92,63) IC S-80827CNMC-B8MIC 671 (A,129,82) Flash ROM Unit(A) PEA012A8