CRT2434 DEH-2130R HIGH POWER CD PLAYER …diagramas.diagramasde.com/otros/Pioneer_DEH-2130R,2100.pdf · model part no. language deh-2130r/x1m/ew crd3137 english, ... unit focus act

PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936

C PIONEER CORPORATION 1999 K-ZZA. NOV. 1999 Printed in Japan

ORDER NO.

CRT2434

HIGH POWER CD PLAYER WITH RDS TUNER

DEH-2130R X1M/EW

ServiceManual

CONTENTS

1. SAFETY INFORMATION ............................................2

2. EXPLODED VIEWS AND PARTS LIST .......................3

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .....8

4. PCB CONNECTION DIAGRAM ................................26

5. ELECTRICAL PARTS LIST ........................................36

6. ADJUSTMENT..........................................................41

7. GENERAL INFORMATION .......................................45

7.1 DIAGNOSIS ........................................................45

7.1.1 TEST MODE..............................................45

7.1.2 DISASSEMBLY .........................................48

7.2 PARTS .................................................................52

7.2.1 IC................................................................52

7.2.2 DISPLAY....................................................59

7.3 OPERATIONAL FLOW CHART...........................60

8. OPERATIONS AND SPECIFICATIONS.....................61

DEH-2100R X1M/EW

DEH-2130R/X1M/EW

- This service manual should be used together with the following manual(s):Model No. Order No. Mech. Module Remarks

CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly

2

DEH-2130R,2100R

- CD Player Service Precautions

1. For pickup unit(CXX1285) handling, please refer

to"Disassembly"(see page 48).

During replacement, handling precautions shall be

taken to prevent an electrostatic discharge(protection

by a short pin).

2. During disassembly, be sure to turn the power off

since an internal IC might be destroyed when a con-

nector is plugged or unplugged.

3. Please checking the grating after changing the ser-

vice pickup unit(see page 43).

1. SAFETY INFORMATION

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do soand refer the repair to a qualified service technician.

1. Safety Precautions for those who Service this Unit.

• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable

results.

Caution:

1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.

2. During repair or tests, do not view laser beam for 10 seconds or longer.

2. A “CLASS 1 LASER PRODUCT” label is affixed to the

bottom of the player.

3. The triangular label is attached to the mechanism

unit frame.

4. Specifications of Laser Diode

Specifications of laser radiation fields to which human access is possible during service.Wavelength = 800 nanometers

CLASS 1LASER PRODUCT

3

DEH-2130R,2100R

1 Cord Assy CDE61232 Screw CBA10023 Handle CNC53954 Bush CNV3930

* 5 Polyethylene Bag E36-615

6 Polyethylene Bag CEG-1627-1 Polyethylene Bag CEG11167-2 Owner's Manual CRD31377-3 Owner's Manual CRD31387-4 Installation Manual CRD3139

* 7-5 Passport CRY1013* 7-6 Warranty Card CRY1157

8 Carton See Contrast table(2)9 Contain Box See Contrast table(2)

10 Protector CHP2243

11 Protector CHP224412 Case Assy CXB3520

Mark No. Description Part No. Mark No. Description Part No.

(1) PACKING SECTION PARTS LIST

NOTE:

- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.

- Screws adjacent to ∇ mark on the product are used for disassembly.

2. EXPLODED VIEWS AND PARTS LIST

2.1 PACKING

10

1

12

6

8

9

11

7

4

3

5

2

Part No.Mark No. Symbol and Description DEH-2130R/X1M/EW DEH-2100R/X1M/EW

8 Carton CHG3951 CHG39509 Contain Box CHL3951 CHL3950

(2) CONTRAST TABLE

DEH-2130R/X1M/EW and DEH-2100R/X1M/EW are constructed the same except for the following:

- Owner's Manual, Installation ManualModel Part No. LanguageDEH-2130R/X1M/EW CRD3137 English, Spanish, GermanDEH-2100R/X1M/EW CRD3138 French, Italian, Dutch

CRD3139 English, Spanish, German, French, Italian, Dutch

4

DEH-2130R,2100R

2.2 EXTERIOR

5

DEH-2130R,2100R

1 Screw BMZ26P120FMC2 Screw BSZ26P060FMC3 Screw BSZ30P060FMC4 Screw BSZ30P120FMC5 Cord Assy CDE6123

6 Cable CDE61607 Fuse(10A) CEK11368 CD Mechanism Module(S8.1) CXK52039 Cover CNC8367

10 Holder CNC8884

11 Spacer CNM491312 Insulator CNM622413 Insulator CNM638614 •••••15 Tuner Amp Assy CWM6764

16 Screw ASZ26P080FMC17 Screw BPZ26P080FMC18 Screw BSZ26P160FMC19 FM/AM Tuner Unit CWE150020 Holder CNC7532

21 Pin Jack(CN301) CKB104122 Terminal(CN403) CKF105923 Connector(CN901) CKM129924 Connector(CN601) CKS358125 Connector(CN605) CKS3838

26 Antenna Jack(CN402) CKX105627 Holder CNC753328 Holder CNC804129 Holder CNC804330 Holder CNC8588

31 Insulator CNM596732 Heat Sink CNR150633 Holder Unit CXB268734 Case Unit CXB403335 Button CAC4836

36 Spring CBH183537 Spring CBH220838 Spring CBH236739 Bracket CNC679140 Holder CNC8042

41 Cover CNM627642 Panel See Contrast table(2)43 Arm CNV469244 Arm CNV472845 Arm CNV5576

46 Screw IMS20P030FZK47 Detach Grille Assy See Contrast table(2)48 Screw BPZ20P100FZK49 Button(Detach) See Contrast table(2)50 Button(+, -) See Contrast table(2)

51 Chassis Unit See Contrast table(2)52 Screw ISS26P055FUC53 IC(IC302) TDA738454 Transistor(Q904, 981) 2SD239655 Button(Source) CAC6494

56 Button(1-6) CAC627557 Button(B, A, Cross) See Contrast table(2)58 Button(Eject) CAC627759 Spring CBH221060 Cover See Contrast table(2)

61 Keyboard Unit See Contrast table(2)62 LCD(LCD1801) CAW155963 Connector(CN1801) CKS358064 Holder CNC851765 Rubber CNV5954

66 Lighting Conductor CNV596567 Rubber CNV596668 Grille Unit See Contrast table(2)69 Cap CNS147270 Resistor RS1/2PMF102J

(1) EXTERIOR SECTION PARTS LIST


Part No.Mark No. Symbol and Description DEH-2130R/X1M/EW DEH-2100R/X1M/EW

42 Panel CNS5340 CNS518847 Detach Grille Assy CXB4595 CXB459249 Button(Detach) CAC5929 CAC578950 Button(+, -) CAC6458 CAC627351 Chassis Unit CXB4624 CXB4623

57 Button(B, A, Cross) CAC6459 CAC627660 Cover CNS5773 CNS577261 Keyboard Unit CWM6779 CWM677868 Grille Unit CXB4612 CXB4611

(2) CONTRAST TABLE

DEH-2130R/X1M/EW and DEH-2100R/X1M/EW are constructed the same except for the following:

6

DEH-2130R,2100R

2.3 CD MECHANISM MODULE

7

DEH-2130R,2100R


1 Control Unit CWX24112 Connector(CN802) CKS21923 Connector(CN801) CKS21934 Connector(CN701) CKS27735 Connector(CN101) CKS3486

6 Screw BMZ20P030FMC7 Screw BSZ20P040FMC8 Screw(M2x3) CBA10779 Screw(M2x5) EBA1028

10 Screw CBA1243

11 Screw(M2x4) CBA136212 Washer CBF103713 Washer CBF103814 Washer CBF106015 •••••

16 Spring CBH207917 Spring CBH211718 Spring CBH231419 Spring CBH211020 Spring CBH2282

21 Spring CBH231822 •••••23 Spring CBH232424 Spring CBH211825 Spring CBH2161

26 Spring CBH216327 Spring CBH218928 Spring CBH224929 Spring CBH226030 Spring CBH2262

31 Bracket CNC856832 Spring CBL136933 Connector CDE553134 Connector CDE553235 Shaft CLA3304

36 Screw(M2.6x6) CBA145837 Frame CNC856538 Frame CNC874939 Lever CNC754640 Arm CNC8663

41 Bracket CNC856742 •••••43 Spacer CNM331544 Sheet CNM665945 •••••

46 •••••47 Ball CNR118948 Belt CNT108649 Roller CNV450950 Arm CNV6037

51 Arm CNV524752 Arm CNV524853 Arm CNV524954 Guide CNV525455 Guide CNV5255

56 Gear CNV525757 Gear CNV525658 Guide CNV617659 Damper CNV617460 Arm CNV6096

61 Arm CNV603162 Arm CNV621163 Guide CNV601264 Guide CNV551065 •••••

66 Guide CNV575167 Clamper CNV601368 Gear CNV581369 Motor Unit(M1) CXB219070 Screw Unit CXB4726

71 Chassis Unit CXB479772 Gear Unit CXB472873 Arm Unit CXB472974 Motor Unit(M2) CXB219575 Lever Unit CXB4730

76 Arm Unit CXB473177 Motor Unit(M3) CXB256278 Arm Unit CXB473279 Bracket Unit CXB479580 Screw JFZ20P025FMC

81 Screw JGZ17P025FZK82 Washer YE20FUC83 Pickup Unit(Service)(P8) CXX128584 Screw IMS26P030FMC

* 85 PCB CNX2982

86 Photo-transistor(Q1, 2) CPT230SX-TU87 Damper CNV617588 Rack CNV601489 Spring CBH2315

- CD MECHANISM MODULE SECTION PARTS LIST

8

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM

AN

T1

TV

AN

T2

TV

RF

TV

IC 3BR9010FVAM 2ND IF 450kHz

M

M

M

LDMD

HOLOGRAMUNIT

FOCUS ACTTRACKING ACT

LD+

MD

FO+

TO+

14

5

4

3

SPINDLEMOTOR

CARRIAGEMOTOR

LOADINGMOTOR

1

2

3

4

3

1

2

SELECTSENSE

DISC SENSE

E

CN801

CN802

D803 D802 D801

VD

S802CLAMP

6

5

11

22

23

21

1

28

21

CDLOAD

CDEJET

CONT

EJTSNS

DSCSNS

CLAMP

CD5VON

VDCONT

VDD IC 701BA05SFP

IN

+5V REGULATOR

24

1

VD

Q981

Q982

B.U

ANTENNA CN402

A

B

27

28

FM FRONT ENDQ3

Q201 Q204

AM RF

FM/AM 1ST IF 10.7MHzT51 Q51 CF51 CF52 CF53

MIXER.IF AMP DETIC 1

PML002A

38 39 42 44 46 63

32 19

46

6

21

18LDET

COMP

34 33 41 44 11 12 1369

70

54

78

65

71

75746157554533

35

22

2225 10 14 12 15 16 13 2 3 4

CF202

VDD

LOCL

VCC

Q411

VCC VDDD

I/DO

CE

2

CK

CE

1

SD

BL

SL

FM

SD

PC

E2

PC

K

PC

E1

SL

SD

PD

IO

NL1

NL2

EEPROM5

6

4

3

IC 2 PM4008A

FM MPX

D

Q101CN101

FOP

TOP

A+C/F

B+D/E

98LD L_OUT

PD

HOME

97

24

23

39

X201

TD/FD

SD/MD

RF-AMP, DSP,SERVO, DAC

IC 201UPD63711GC

16CN701 CN605

17

1

8

24

CDL

IC 301BA5985FM

S801HOME12

16

18

11

14

13

10

9

SOP

TOP

FOP

SOM

COP

COM

LOP

LOM

FWD

REV

MUTE

25 24

CD

DR

IVE

R

7 18

19

20

14

3

2

4

CLAMP

DINC

EJTD

CDLOAD

EJET

CONT

Q202

32

PD

TUNER AMP ASSY

FM/AM TUNER UNIT

CONTROL UNITPICKUP UNIT(SERVICE)(P8)

PHOTO UNIT(S8)

4

VD

CD5VON

Q472 Q474 Q476

RDSDECODER

IC 701PM4009A

20

11 12

X702

Q477

VDD

TMUTE

FM/AM

LDET

8

SD

BW

NL1

9

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

KYDT

DPDT

LCD DRIVER

IC 1801PD6293A

3

4

5

3

4

5

KEY MATRIX

SD

SL

TUNPCE

TUNPCK

TUNPCE2

TUNPDO

LOCL

IN1

IN2

6

76

14

13

48

12

67

2

3

SYSTEMCONTROLLER

IC 601(1/2)PE5090A

VSTVCKVDT

B.UVDD

Q903B.U

BACKUP

FL–

FL+

RL–

RL+

ACC

2

1

9

11

10

12

4

ELECTRONIC VOLUME/SOURCE SELECTOR

IC 301SN761029DL

SYSTEMCONTROLLER

IC 601(2/2)PE5090A

ASENS63

BSENS64

SYSPW42

MUTE44

KYDT8

DPDT9

RESET60

SWVDD41

Fout19

Rout20

POWER AMP

IC 302TDA7384

14

12

22 4

5

3

21

23

FL

MUTE STBY

RL

B.Ubsens

asens

Q902Q351 MUTE

Q942 Q941

C KEYBOARD UNIT

CN1801CN601

LCD

22 23

X1801

20

18

Q650

RESETIC 602

S–80834ANY VDD1 2

SY

SP

W

GND

5B.REMOTE

FUSE10A

CD5VON

31

34

23

80

79

27

22

35

VDCONT

CLAMP

DSCSNS

EJTSNS

CDLOAD

CDEJECT

CONT

TUNPDI11PDIO

VST/ VCK/ VDT

Q901

VDD

VDD

VLCD

50

10

Q346

CN301

REAR L CH

Q353

7TELIN

Q951

RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-ACCGND

BACKUP

BACK UP

FL–

FL+

RL–

RL+

B.REM

ACC

GND

B.REM

CELLULAR MUTE

CELLULAR MUTE

66

61

21FM/AM

LDET

TMUTE

2 NL1

SDBW10

TELIN32

10

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS

LIST”.

A-a A-b

A-aA-a A-b A-b

A-b A-b A-a A-a

Large sizeSCH diagram

Guide page

Detailed page

A

A-aD

SP

-201

M-S

00B

162

162

123

123

272

272

4.194MHz

CSS1047

104

102

0R0

R699 0R0

FM(100%):-15.5dBsAM (30%):-26dBs

CD:+4.FM(100%):-15AM (30%):-26

FM/AM TUNER UNIT

For resistors and capacitors in the circuit diagrams, their resistance values orcapacitance values are expressed in codes:

Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms

*Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V

The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.

Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.

NOTE :

Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.

R

SYSTEM CONTROLLER

KEYBOARDUNIT

B

C

11

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

A-b

A

332/

16

(B2)

600µH

102(1/2W)

>

CEK1136

4.1dBs5.5dBs6dBs

CD:+10.1dBsFM(100%):+6.5dBsAM (30%):-3dBs

CD:+10.1dBsFM(100%):+6.5dBsAM (30%):-3dBs

CD:+36.1dBsFM(100%):+32.5dBsAM (30%):+23dBs

CD:+4.1dBs

CELLULAR MUTECD

ME

CH

AN

ISM

MO

DU

LE

POWER AMP

SOURCE SELECTOR/E.VOL

Reset

VD REGULATOR

TUNER AMP ASSYAA

RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-ACCGND

B.REM

BACKUP

D

12

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

A-a

A-a

A-b

DSP-201M-S00B

162

162123 123

272 272

4.19

4MH

z

CS

S10

47

0

FM(1

00%

):-1

5.5d

Bs

AM

(30

%):

-26d

Bs

CD

:+4.

1dB

sFM

(100

%):

-15.

5dB

sA

M (

30%

):-2

6dB

s

FM/A

M T

UN

ER

UN

IT

SO

UR

CE

E.V

OL

B

1

13

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

A-a

A-a

A-b

104

102

0R0

R69

90R

0

CD MECHANISM MODULE

For

resi

sto

rs a

nd

cap

acit

ors

in t

he

circ

uit

dia

gra

ms,

th

eir

resi

stan

ce v

alu

es o

rca

pac

itan

ce v

alu

es a

re e

xpre

ssed

in c

od

es:

Ex.

*R

esis

tors

C

od

e

P

ract

ical

val

ue

1

23

12k

oh

ms

1

03

10k

oh

ms

*C

apac

ito

rs

Co

de

P

ract

ical

val

ue

1

03

0.01

µF

101

/10

10

0µF/

10V

Th

e >

mar

k fo

un

d o

n s

om

e co

mp

on

ent

par

ts in

dic

ates

the

imp

ort

ance

of

the

safe

ty f

acto

r o

f th

e p

art.

Th

eref

ore

, wh

en r

epla

cin

g, b

e su

re t

o u

se p

arts

of

iden

tica

l des

ign

atio

n.

Sym

bo

l in

dic

ates

a r

esis

tor.

No

dif

fere

nti

atio

n is

mad

e b

etw

een

ch

ip r

esis

tors

an

dd

iscr

ete

resi

sto

rs.

NO

TE

: Sym

bo

l in

dic

ates

a c

apac

ito

r.N

o d

iffe

ren

tiat

ion

is m

ade

bet

wee

n c

hip

cap

acit

ors

an

dd

iscr

ete

cap

acit

ors

.

Res

et

SY

ST

EM

CO

NT

RO

LLE

R

KE

YB

OA

RD

UN

IT

C

D

2

14

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

A-a

A-b

A-b

332/16

600µ

H

>

CE

K11

36

.1d

Bs

5.5d

Bs

6dB

s

CD

:+10

.1d

Bs

FM(1

00%

):+6

.5d

Bs

AM

(30

%):

-3d

Bs

CD

:+10

.1d

Bs

FM(1

00%

):+6

.5d

Bs

AM

(30

%):

-3d

Bs

CD

:+36

.1d

Bs

FM(1

00%

):+3

2.5d

Bs

AM

(30

%):

+23d

Bs

PO

WE

R A

MP

SO

UR

CE

SE

LEC

TO

R/

E.V

OL

TU

NE

R A

MP

AS

SY

AA

1

15

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

A-b

A-a

A-b

(B2)

600µ

H

102(

1/2W

)

CD

:+4.

1dB

s

CE

LLU

LAR

MU

TE

CD MECHANISM MODULE

Res

et

VD

RE

GU

LAT

OR

RR +RR -

FR +FR -

FL +FL -

RL +RL -

ACC

GN

D

B. REM

BACK

UP

D

2

16

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

B

3.3 FM/AM TUNER UNIT

KV

1410

(23)

KV

1410

(23)

MarkNoneF0F65F125A0A74A125

Band–FMFMFMAMAMAM

Input Level–0dBf65dBf125dBf0dBµ74dBµ125dBµ

DA

N21

7U

DA

N21

7U

BA

FM/AM TUNER UNIT

17

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

B

KV

1410

(23)

18

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

3.4 KEYBOARD UNIT

C KEYBOARD UNIT

C

LCD DRIVER,KEY CONTROLLER

PD6293A

CAW1559

19

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

C

DISP

PTY TA/AF

LOCAL/BSM

DEH-2130R/X1M/EW DEH-2100R/X1M/EW

IL1801-1804 CEL1638(14V 40mA) CEL1547(14V 40mA)A

CN

601

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

BA05SFP

(SERVICE)(P8)PICKUP UNIT

PHOTO UNIT(S8)

CONTROL UNIT

SPINDLE MOTOR

Q2 CPT230SX-TUQ1 CPT230SX-TU

M3 CXB2562

CARRIAGE MOTOR

M1 CXB2190

M2 CXB2195

LOADING MOTOR

RF-AMP, SE

5V REGULATOR

CD DRIVER

CN101

CN802

CN801


E

D

E

D20

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

MP, SERVO, DSP, DAC, LPF

SWITCHES:CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFFThe underlined indicates the switch position.

CN701

AC

N60

5

D 21

22

DEH-2130R,2100R

1 RFI 0.5V/div. 0.5µs/div.Normal mode: play

1 CH1: RFI 1V/div.2 CH2: MIRR 5V/div.

Test mode: Tracking open

0.5ms/div. 1 CH1: RFI 1V/div.2 CH2: MIRR 5V/div.

Normal mode: The defect partpasses 800µm

0.5ms/div.

3 CH1: FD 0.5V/div.4 CH2: FO+ 2V/div.

Test mode: No disc, Focus close

0.2s/div. 3 CH1: FD 0.5V/div.5 CH2: FOK 2V/div.

Normal mode: Focus close

0.2s/div. 6 CH1: FE 0.5V/div.7 CH2: XSI 2V/div.

Normal mode: Focus close

1ms/div.

REFO →

8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: 32 tracks jump (FWD)

0.5ms/div. 8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: Single jump (FWD)

0.5ms/div. 8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: 100 tracks jump (FWD)

5ms/div.

6 CH1: FE 0.1V/div.3 CH2: FD 0.2V/div.

Normal mode: Play

20ms/div. 3 CH1: FD 0.5V/div.0 CH2: MD 1V/div.

Normal mode: Focus close (12cm)

0.5s/div. 3 CH1: FD 0.5V/div.0 CH2: MD 1V/div.

Normal mode: Focus close (8cm)

0.5s/div.

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

GND →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

- Waveforms

Note:1. The encircled numbers denote measuring pointes in the circuit diagram.2. Reference voltage

REFO:2.5V

REFO →

REFO →

REFO →

REFO →

23

DEH-2130R,2100R

8 CH1: TE 0.2V/div.9 CH2: TD 0.2V/div.

Normal mode: play

8 CH1: TE 0.5V/div.! CH2: SD 0.5V/div.TEST mode: 100 Tracks jump(FWD)

5ms/div. 0 MD 0.5V/div. 0.1s/div.

Normal mode: Play (12cm)

0 MD 1V/div. 10ms/div.Normal mode:Long Search (12cm)

@ EFM 1V/div. 5µs/div.

Normal mode: play

8 CH1: TE 1V/div.# CH2: TEC 1V/div.

Test mode: Focus closeTracking open

2ms/div.

8 CH1: TE 0.5V/div.6 CH2: FE 0.5V/div.

Normal mode: AGC after focus close

0.2s/div.$ PLCK 2V/div. 0.5µs/div.

Normal mode: play

20ms/div.

% SCKO 2V/div. 1µs/div.

Normal mode: play

^ Dout 2V/div. 10µs/div.

Normal mode: play

& LRCK 2V/div. 20µs/div.

Normal mode: play

* VD 5V/div. 50ms/div.

Normal mode: No disc

GND →

REFO →

REFO →

GND →

REFO →

REFO →

REFO →

REFO →REFO →

REFO →

REFO →

REFO →

REFO →

GND →

REFO →

GND →

REFO →

GND →

REFO →

GND →

REFO →

24

DEH-2130R,2100R

( CH1: R OUT 1V/div.) CH2: L OUT 1V/div.

Normal mode: Play (1kHz 0dB)

6 CH1: FE 0.2V/div.3 CH2: FD 0.5V/div.

Normal mode: During AGC

1ms/div. 8 CH1: TE 0.2V/div.9 CH2: TD 0.5V/div.

Normal mode: During AGC

1 CH1: RFI 1V/div.⁄ CH2: HOLD 5V/div.

Normal mode: The defect part passes800µm(B.D)

0.2ms/div. 1ms/div.

0.5ms/div. 3 CH1: FD 0.5V/div.⁄ CH2: HOLD 5V/div.


0.5ms/div.9 CH1: TD 0.1V/div.⁄ CH2: HOLD 5V/div.


0.5ms/div.

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO → REFO →

REFO →

REFO →

REFO →

25

DEH-2130R,2100R

26

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

4. PCB CONNECTION DIAGRAM

4.1 TUNER AMP ASSY

NOTE FOR PCB DIAGRAMS

1. The parts mounted on this PCB

include all necessary parts for

several destination.

For further information for

respective destinations, be sure

to check with the schematic dia-

gram.

2. Viewpoint of PCB diagrams

A

CapacitorConnector

P.C.Board Chip Part

SIDE A

SIDE B

CORD ASSY

CN

701

D

C CN1801

A TUNER AMP ASSY

27

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

A

SIDE A

B

28

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

A

A TUNER AMP ASSY

29

DEH-2130R,2100R5 6 7 8

5 6 7 8

D

C

B

A

A

SIDE B

30

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

4.2 FM/AM TUNER UNIT

SIDE A

BFM

/AM

TU

NE

R U

NIT

A

B

31

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

SIDE B

BFM

/AM

TU

NE

R U

NIT

B

32

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

4.3 KEYBOARD UNIT

C

C

SIDE A

KE

YB

OA

RD

UN

IT

+

DIS

P

12

34

56

TA

/AF

PT

YLO

CA

L/B

SM

BA

ND

EJE

CT

'

][

'A

UD

IO

SO

UR

CE

/OFF

-

33

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

C

C

SIDE B

KE

YB

OA

RD

UN

ITA

CN

601

34

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A


CO

NT

RO

L U

NIT

HO

ME

M1

CA

RR

IAG

E M

OT

OR

M2

LOA

DIN

G M

OT

OR

M3

SP

IND

LE M

OT

OR

PIC

KU

P U

NIT

(SE

RV

ICE

)(P

8)

CN

802

CN

605

3 2 1

PH

OT

O U

NIT

(S8)

SIDE A

A D

ED

D E

E

35

DEH-2130R,2100R1 2 3 4

1 2 3 4

D

C

B

A

CLA

MP

SIDE B

CO

NT

RO

L U

NIT

D

D

36

DEH-2130R,2100R

5. ELECTRICAL PARTS LIST

NOTES:

- Parts whose parts numbers are omitted are subject to being not supplied.

- The part numbers shown below indicate chip components.

Chip Resistor

RS1/_S___J,RS1/__S___J

Chip Capacitor (except for CQS.....)

CKS....., CCS....., CSZS.....

=====Circuit Symbol and No.===Part Name Part No.--- ------ ------------------------------------------ -------------------------

Unit Number : CWM6764Unit Name : Tuner Amp Assy

MISCELLANEOUS

IC 301 IC SN761029DLIC 302 IC TDA7384IC 601 IC PE5090AIC 602 IC S-80834ANYIC 701 IC PM4009A

Q 346 Transistor RN1610Q 351 Transistor DTC114EKQ 353 Transistor DTA124EKQ 411 Transistor 2SC2412KQ 412 Transistor 2SC2412K

Q 472 Transistor RN1610Q 474 Transistor 2SD1757KQ 475 Transistor 2SD1757KQ 476 Transistor 2SC2412KQ 477 Transistor DTA124EK

Q 650 Transistor 2SA1037KQ 901 Transistor 2SC2412KQ 902 Transistor 2SC2412KQ 903 Transistor 2SD1859Q 904 Transistor 2SD2396

Q 905 Transistor 2SB1243Q 906 Transistor DTC114EKQ 941 Transistor 2SB1243Q 942 Transistor DTC114EKQ 951 Transistor 2SA1037K

Q 981 Transistor 2SD2396Q 982 Transistor RN46A1D 650 Diode 1SS270D 651 Diode 1SS270D 652 Diode 1SS270

D 653 Diode 1SS270D 654 Diode 1SS270D 655 Diode 1SS270D 901 Diode HZS7L(C2)D 902 Diode S5688G

D 903 Diode S5688GD 904 Diode HZS7L(A1)D 905 Diode S5688GD 906 Diode HZS6L(B2)D 907 Diode HZS9L(B3)

D 941 Diode S5688GD 942 Diode S5688GD 951 Diode 1SS270D 952 Diode 1SS270D 981 Diode HZS9L(B1)

L 401 Ferri-Inductor LAU4R7KL 402 Ferri-Inductor LAU2R2KL 403 Inductor LAU100KL 610 Ferri-Inductor LAU101KL 611 Ferri-Inductor LAU2R2K

L 650 Ferri-Inductor LAU2R2KL 703 Inductor LAU100KL 704 Ferri-Inductor LAU101KL 901 Choke Coil 600µH CTH1221L 951 Ferri-Inductor LAU2R2K

TH 601 Thermistor CCX1031X 610 Ceramic Resonator 4.194MHz CSS1047X 702 Crystal Resonator 3.648MHz CSS1447AR 946 Arrester DSP-201M-S00B

FM/AM Tuner Unit CWE1500

RESISTORS

R 310 RD1/4PU222JR 311 RD1/4PU222JR 312 RS1/10S272JR 313 RS1/10S272JR 314 RS1/10S151J

R 315 RS1/10S151JR 316 RS1/10S0R0JR 317 RS1/10S121JR 318 RD1/4PU104JR 319 RD1/4PU104J

R 320 RS1/10S121JR 321 RS1/10S101JR 322 RS1/10S101JR 342 RS1/8S821JR 343 RS1/8S821J


R 360 RD1/4PU153JR 411 RS1/10S681JR 412 RS1/10S681JR 413 RS1/10S681JR 414 RS1/10S103J

R 415 RS1/8S681JR 416 RD1/4PU473JR 417 RD1/4PU472JR 418 RS1/10S473JR 419 RS1/10S473J




A

37

DEH-2130R,2100R


R 444 RS1/10S472JR 445 RS1/8S473JR 446 RS1/10S224JR 447 RS1/10S0R0JR 460 RS1/10S162J


R 476 RS1/10S223JR 477 RS1/10S222JR 478 RD1/4PU224JR 479 RS1/10S224JR 611 RS1/10S102J

R 614 RS1/8S0R0JR 619 RS1/10S0R0JR 620 RN1/10SE2202DR 622 RD1/4PU222JR 623 RD1/4PU222J

R 624 RS1/10S473JR 625 RS1/10S473JR 626 RS1/10S473JR 627 RD1/4PU473JR 628 RD1/4PU222J


R 653 RD1/4PU222JR 654 RS1/10S473JR 655 RS1/10S103JR 656 RS1/10S103JR 657 RD1/4PU102J

R 658 RD1/4PU102JR 660 RS1/10S1R0JR 681 RD1/4PU681JR 682 RS1/10S102JR 683 RD1/4PU102J

R 684 RS1/10S102JR 699 RS1/10S0R0JR 713 RS1/10S225JR 717 RD1/4PU102JR 721 RS1/10S102J

R 722 RS1/10S102JR 723 RS1/10S102JR 724 RS1/10S681JR 725 RS1/10S0R0JR 726 RS1/10S0R0J

R 727 RS1/8S0R0JR 901 RS1/10S473JR 902 RD1/4PU103JR 903 RD1/4PU103JR 904 RS1/10S473J

R 905 RS1/10S102JR 906 RS1/10S473JR 907 RS1/10S473JR 908 RS1/10S472JR 909 RD1/4PU103J

R 911 RS1/10S122JR 912 RD1/4PU103JR 914 RD1/4PU152JR 916 RS1/10S221JR 918 RS1/10S1R0J

R 941 RD1/4PU472JR 942 RD1/4PU152JR 951 RS1/10S153JR 953 RS1/10S472JR 954 RD1/4PU102J

R 955 RD1/4PU473JR 981 RS1/10S472JR 982 RS1/10S222JR 983 RD1/4PU221JR 984 RD1/4PU221J

CAPACITORS

C 310 CKSQYB105K16C 311 CKSQYB104K16C 312 CEJA2R2M50C 313 CKSQYB105K16C 314 CKSYB104K16

C 315 CKSQYB102K50C 316 CKSQYB102K50C 317 CEJA100M16C 318 CEJA100M16C 319 CKSQYB822K50

C 320 CKSQYB822K50C 321 CEAL1R0M50C 322 CEJA1R0M50C 323 CKSQYB183K50C 324 CKSQYB183K50

C 325 CKSQYB104K16C 326 CKSQYB104K16C 327 CKSQYB104K16C 328 CKSQYB104K16C 329 CEJA2R2M50

C 330 CEJA4R7M50C 332 CKSQYB473K16C 333 CKSQYB104K16C 334 CKSQYB104K16C 335 CEAL470M10

C 340 CEAL2R2M50C 341 CEJA2R2M50C 350 CEJA330M10C 361 CEJA2R2M50C 362 CKSYB225K16

C 363 CEJA100M16C 364 CKSYB474K16C 365 CKSQYB474K16C 366 CKSYB474K16C 367 CKSQYB474K16

C 368 CKSQYB474K16C 369 CKSYB474K16C 370 CKSQYB474K16C 371 CKSYB474K16C 372 CKSQYB225K10

C 390 CKSQYB104K16C 391 3300µF/16V CCH1368C 411 CKSQYB223K25C 412 CKSQYB223K25C 413 CKSQYB102K50

C 414 CEJA220M10C 415 CKSQYB473K16C 416 CEAL101M10C 417 CKSQYB472K50C 418 CKSQYB472K50



38

DEH-2130R,2100R

C 441 CKSQYB182K50C 442 CKSQYB223K25C 462 CKSQYB123K25C 463 CKSQYB123K25C 466 CEJA1R0M50

C 467 CEJA1R0M50C 490 CKSQYB103K50C 493 CCSQCH100J50C 612 CEJA4R7M35C 613 CKSQYB473K16

C 614 CKSQYB102K50C 621 CCSQCH101J50C 630 CKSQYB473K16C 631 CEAL2R2M50C 650 CKSQYB104K16

C 711 CEAL220M6R3C 712 CKSQYB104K16C 714 CKSQYB471K50C 715 CKSQYB104K16C 718 CKSQYB471K50

C 719 CEAL220M6R3C 720 CKSQYB104K16C 725 CCSQCH270J50C 726 CCSQCH270J50C 901 CEJA101M10

C 902 CKSQYB473K16C 903 470µF/16V CCH1331C 904 CKSQYB473K16C 905 330µF/16V CCH1326C 906 CKSQYB103K50

C 907 CEJA101M16C 941 CKSQYB473K16C 981 CEJA101M10C 982 CKSQYB102K50C 983 CKSQYB473K16

Unit Number : CWE1500Unit Name : FM/AM Tuner Unit

MISCELLANEOUS

IC 1 IC PML002AIC 2 IC PM4008AIC 3 IC BR9010FVQ 1 Transistor 2SC4081Q 2 Transistor DTC124EU

Q 3 FET 3SK263Q 51 Transistor 2SC4081Q 201 FET 2SK932Q 202 Transistor DTC124EUQ 204 Transistor 2SC4081

D 1 Diode KV1410(23)D 2 Diode 1SV248D 4 Diode KV1410(23)D 6 Diode KV1410(23)D 101 Diode 1SS355

D 201 Diode DAN217UD 202 Diode DAN217UD 903 Diode KV1410(23)D 904 Diode SVC253L 1 Coil CTC1155

L 2 Coil CTC1155L 3 Inductor LCTB100K2125L 4 Coil CTC1155L 201 Inductor LCTB330K1608L 202 Inductor CTF1287

L 203 Inductor LCTA121J3225L 901 Coil CTC1154L 902 Inductor LCTA3R3J3225L 904 Inductor LCTBR47K1608L 905 Inductor LCTBR47K1608

T 51 Coil CTE1132CF 51 Ceramic Filter CTF1442CF 52 Ceramic Filter CTF1442CF 53 Ceramic Filter CTF1442CF 202 Ceramic Filter CTF1348

X 901 Crystal Resonator 10.250MHz CSS1432

RESISTORS







R 104 RS1/16S562JR 106 RS1/16S0R0JR 108 RS1/16S0R0JR 110 RS1/16S154JR 111 RS1/16S273J


R 117 RS1/16S333JR 118 RS1/16S223JR 122 RS1/16S0R0JR 202 RS1/16S472JR 203 RS1/16S225J





B

39

DEH-2130R,2100R

R 907 RS1/16S103JR 908 RS1/16S681JR 909 RS1/16S473JR 914 RS1/16S562J

CAPACITORS

C 1 CCSQCH5R0C50C 2 CCSRCH5R0C50C 4 CCSRCJ3R0C50C 6 CKSQYB105K10C 8 CKSRYB222K50

C 10 CCSRCH220J50C 11 CCSRCH150J50C 12 CCSRCH8R0D50C 14 CCSRCJ3R0C50C 15 CKSRYB103K50

C 16 CKSRYB222K50C 17 CKSRYB222K50C 18 CCSRCJ3R0C50C 19 CKSRYB103K50C 20 CKSRYB103K50

C 21 CKSRYB103K50C 24 CKSQYB334K16C 31 CKSRYB222K50C 32 CCSRCH470J50C 35 CKSRYB103K50

C 51 CKSRYB103K50C 52 CKSRYB473K16C 53 CCSRCK2R0C50C 54 CKSRYB103K50C 55 CKSRYB104K16

C 56 CKSRYB104K16C 58 CKSQYB224K16C 59 CKSRYB223K25C 60 CKSRYB104K16C 101 CEALNP100M10

C 102 CCSRCH151J50C 103 CKSRYB473K16C 105 CKSRYB682K25C 106 CEAL2R2M50C 107 CKSRYB103K50

C 108 CKSQYB474K16C 109 CKSQYB474K16C 110 CKSRYB104K16C 111 CKSRYB104K16C 112 CKSRYB104K16

C 113 CKSRYB123K25C 114 CEAL220M6R3C 115 CKSRYB473K16C 116 CEAL2R2M50C 117 CKSRYB102K50

C 120 CKSRYB153K25C 121 CKSRYB332K50C 122 CKSRYB682K25C 123 CKSRYB681K50C 125 CKSRYB103K50

C 126 CKSRYB103K50C 127 CEAL2R2M50C 128 CKSRYB103K50C 201 CCSRCH471J50C 202 CCSRCH100D50


C 208 CCSRCH560J50C 209 CEAL470M6R3C 210 CKSRYB103K50C 211 CKSRYB103K50C 212 CCSRCH101J50

C 215 CKSRYB223K25C 216 CKSQYB334K16C 217 CKSRYB103K50C 219 CKSQYB105K10C 220 CKSRYB104K16

C 221 CKSRYB473K16C 222 CKSQYB334K16C 223 CKSQYB474K16C 224 CKSRYB104K16C 225 CKSRYB272K50

C 226 CKSRYB682K25C 902 CCSRCH270J50C 904 CKSRYB223K25C 905 CKSRYB103K50C 906 CCSRTH100D50

C 907 CCSRTH150J50C 909 CCSRTH100D50C 910 CKSRYB332K50C 912 CKSQYB474K16C 913 CKSRYB223K25

C 914 CKSRYB682K25C 915 CKSQYB223K25C 916 CKSQYB474K16C 917 CKSYB475K10C 918 CKSRYB223K25

C 919 CKSQYB225K10C 920 CCSRCH270J50C 921 CCSRCH270J50C 922 CKSYB105K16C 923 CKSRYB103K50

Unit Number : CWM6779(DEH-2130R): CWM6778(DEH-2100R)

Unit Name : Keyboard Unit

MISCELLANEOUS

IC 1801 IC PD6293AD 1801 Diode MA152WKD 1802 Diode MA152WAX 1801 Ceramic Resonator 4.97MHz CSS1422IL 1801 Lamp 14V 40mA(DEH-2130R) CEL1638

IL 1801 Lamp 14V 40mA(DEH-2100R) CEL1547IL 1802 Lamp 14V 40mA(DEH-2130R) CEL1638IL 1802 Lamp 14V 40mA(DEH-2100R) CEL1547IL 1803 Lamp 14V 40mA(DEH-2130R) CEL1638IL 1803 Lamp 14V 40mA(DEH-2100R) CEL1547

IL 1804 Lamp 14V 40mA(DEH-2130R) CEL1638IL 1804 Lamp 14V 40mA(DEH-2100R) CEL1547LCD1801 LCD CAW1559

RESISTORS


R 1806 RS1/10S471J

CAPACITORS

C 1801 CKSQYB103K25



C

40

DEH-2130R,2100R

Unit Number : CWX2411Unit Name : Control Unit

MISCELLANEOUS

IC 201 IC UPD63711GCIC 301 IC BA5985FMIC 701 IC BA05SFPQ 101 Transistor 2SB1132D 801 LED CL200IRX

D 802 LED CL200IRXX 201 Ceramic Oscillator 16.934MHz CSS1456S 801 Spring Switch(HOME) CSN1051S 802 Spring Switch(CLAMP) CSN1052

RESISTORS



R 302 RS1/16S153JR 303 RS1/16S103JR 501 RS1/16S102JR 502 RA4C681JR 601 RS1/16S102J

R 602 RS1/16S102JR 605 RS1/16S0R0JR 606 RS1/16S0R0JR 801 RS1/8S751JR 803 RS1/8S751J

R 902 RS1/16S0R0JR 906 RS1/16S0R0J

CAPACITORS

C 101 CCSRCH102J25C 102 CKSRYB104K16C 103 CEV101M6R3C 104 CEV470M6R3C 105 CKSQYB334K16

C 106 CKSQYB334K16C 107 CKSQYB334K16C 201 CKSRYB104K16C 202 CKSRYB471K50C 203 CKSRYB104K16

C 205 CEV101M6R3C 206 CKSRYB104K16C 207 CKSRYB104K16C 208 CKSRYB104K16C 209 CKSRYB104K16


C 215 CKSRYB104K16C 216 CCSRCJ3R0C50C 217 CCSRCH270J50C 218 CKSRYB104K16C 219 CCSRCH181J50

C 220 CCSRCH510J50C 221 CKSRYB682K25C 222 CEV220M6R3C 223 CKSRYB103K25C 224 CKSRYB224K10

C 301 CEV101M10C 603 CCSQSL152J50C 604 CCSQSL152J50C 702 10µF/10V CCH1349C 703 CKSQYB334K16

Unit Number :Unit Name : Photo Unit(S8)

Q 1 Photo-transistor CPT230SX-TUQ 2 Photo-transistor CPT230SX-TU

Miscellaneous Parts List

Pickup Unit(Service)(P8) CXX1285M 1 Motor Unit(CARRIAGE) CXB2190M 2 Motor Unit(LOADING) CXB2195M 3 Motor Unit(SPINDLE) CXB2562

Fuse(10A) CEK1136

E

D



41

DEH-2130R,2100R

1) Precautions• This unit uses a single power supply (+5V) for the reg-

ulator. The signal reference potential, therefore, isconnected to REFO(approx. 2.5V) instead of GND.If REFO and GND are connected to each other by mis-take during adjustments, not only will it be impossi-ble to measure the potential correctly, but the servowill malfunction and a severe shock will be applied tothe pick-up. To avoid this, take special note of the fol-lowing.Do not connect the negative probe of the measuringequipment to REFO and GND together. It is especiallyimportant not to connect the channel 1 negativeprobe of the oscilloscope to REFO with the channel 2negative probe connected to GND.Since the frame of the measuring instrument is usual-ly at the same potential as the negative probe, changethe frame of the measuring instrument to floating sta-tus.If by accident REFO comes in contact with GND,immediately switch the regulator or power OFF.

• Always make sure the regulator is OFF when connect-ing and disconnecting the various filters and wiringrequired for measurements.

• Before proceeding to further adjustments and mea-surements after switching regulator ON, let the playerrun for about one minute to allow the circuits to stabi-lize.

• Since the protective systems in the unit's software arerendered inoperative in test mode, be very careful toavoid mechanical and /or electrical shocks to the sys-tem when making adjustment.

• Disc detection during loading and eject operations isperformed by means of a photo transistor in thisunit.Consequently, if the inside of the unit is exposedto a strong light source when the outer casing isremoved for repairs or adjustment, the following mal-functions may occur.

*During PLAY, even if the eject button ispressed,the disc will not be ejected and the unitwill remain in the PLAY mode.

*The unit will not load a disc.When the unit malfunctions this way, either re-posi-tion the light source, move the unit or cover the phototransistor.

2) Test ModeThis mode is used for adjusting the CD mechanismmodule of the device.

• Test mode starting procedureReset while pressing the 4 and 6 keys together.

• Test mode cancellationSwitch ACC, back-up OFF.

• After pressing the EJECT key, do not press any otherkey until the disk is completely ejected.

• If the ] or [ key is pressed while focus search is inprogress, immediately turn the power off (otherwisethe actuator may be damaged due to adhesion of thelenses).

• Jump operation of TRs other than 100TR continuesafter releasing the key. CRG move and 100TR jumpoperations are brought into the “Tracking close” sta-tus when the key is released.

• Powering Off/On resets the jump mode to “1TR”, andthe automatic adjustment value to the initial value.

6. ADJUSTMENT

6.1 CD ADJUSTMENT

42

DEH-2130R,2100R

- Flow Chart

4

3

Reset

SOURCE

New test mode

6

[

BAND

BAND

BAND

BAND

BAND

3

*2*1

6

6

6

6

1

2

1

2]

] [

Select CD

Focus ModeSelect

Focus Close/S Curve Check

CRG- Auto AdjustmentDisplay Select

<Tracking Servo Close> CRG+

RF AGC Coefficient Display/Rough Servo and RF AGC

Tracking Open

TrackingOpen

T. Close andFit Servo

] [

1

3

Display

2

3

Displayor

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

CRG-CRG+ T.BalanceAdjustment

*4F, T, RF AGC/F.Bias Display Select

F, T AGC andRF AGC

Power ON(Adjustment for T.Offset)

*5 *6 *6

*7CRG/TR Jump NO.Select

CRG+/TR Jump+

CRG-/TR Jump-

Power OFF

Display

Display

Display

T.Close andF,T AGC andRF AGC andFit Servo

Power ON(Not adjustment for T.Offset)

Display

Display

2

Power OFF

Power OFF

Power OFF 8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

91 91 91TRK SECMIN

0x 0x 0xTRK SECMIN

00 00 00TRK SECMIN

99 99 99TRK SECMIN

Test Mode In

*3

*1

*3

*6

*2

*5

*7

*4

F.Cancel T.Offset The original display

1TR/4TR/10TR/32TR/100TR"00", "99"→Focus Close / "01"→S.Curve

1TR 4TR91(81) 92(82)

CRG Move96(86)

100TR95(85)

32TR94(84)

10TR93(83)

Focus Close00(99)

LD Off02

S.Curve01

CRG Move,100TR Jump

TRK, MIN, SEC F.AGC Gain T.AGC Gain F.Bias

43

DEH-2130R,2100R

• Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjustedPU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, ifthe PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to performtrack search operations, or taking a long time for track searching.

• Method :

• Measuring Equipment • Oscilloscope, Two L.P.F.• Measuring Points • E, F, REFOUT• Disc • ABEX TCD-784• Mode • TEST MODE

• Checking Procedure1. In test mode, load the disc and switch the 5V regulator on.2. Using the ] and [ buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-

ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on thefourth press.

4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-ence is within 75° . Refer to the photographs supplied to determine the phase angle.

5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is anyimprovement. If, after trying this a number of times, the grating angle does not become less than 75° then themechanism should be judged to be at fault.

• NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may beseen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-age angle.

• HintReloading the disc changes the clamp position and may decrease the "wobble".

F

REFO

E

100kΩ

390pF

100kΩ

390pF

E

REFO

F

REFO

L.P.F.

L.P.F.

CONTROL UNIT

Xch Ych

Oscilloscope

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

44

DEH-2130R,2100R

Grating waveform Ech → Xch 20mV/div, ACFch → Ych 20mV/div, AC

45°

0°

75°

60°

30°

90°

45

DEH-2130R,2100R

7. GENERAL INFORMATION

7.1 DIAGNOSIS

7.1.1 TEST MODE

- Error Messages

If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the

error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the

users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (min-

utes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains

in blank as before.

2) Head unit display examples

Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERROR–xx ERR–xx E–xx

OR

Err–xx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)

10 Electricity Carriage Home NG CRG can't be moved to inner diameter.

CRG can't be moved from inner diameter.

→ Failure on home switch or CRG move mechanism.

11 Electricity Focus Servo NG Focusing not available.

→ Stains on rear side of disc or excessive vibrations on REWRITABLE.

12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).

→ Failure on spindle, stains or damages on disc, or excessive vibrations.

Subcode NG A disc not containing CD-R data is found. Turned over disc are found,

though rarely.

→ Failure on home switch or CRG move mechanism.

RF AMP NG An appropriate RF AMP gain can't be determined.

→ CD signal error.

17 Electricity Setup NG APC protection doesn't work. Focus can be easily lost.

→ Damages or stains on disc, or excessive vibrations.

30 Electricity Search Time Out Failed to reach target address.

→ CRG tracking error or damages on disc.

A0 System Power Supply NG Power (VD) is ground faulted.

→ Failure on SW transistor or power supply (failure on connector).

Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).

Unreadable TOC does not constitute an error. An intended operation continues in this case.

A newly designed head unit must conform to the example given above.

Upper digits of an error code are subdivided as shown below:

1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.

46

DEH-2130R,2100R

- New Test Mode

S-CD plays the same way as before.

If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its

cause and time occurred (in absolute time) are displayed.

During setup, operational status of the control software (internal RAM: CPOINT) is displayed.

These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis.

(1) Shifting to the New Test Mode

1 Turn on the current test mode by starting the reset from the key.

2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the

disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off.

3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off.

You can reset the new test mode by turning on the reset start.

* With some products, the new test mode can be reset through the same operations as that employed for shifting to

the STBY mode (while maintaining the Acc turned off).

(2) Key Correspondence

Key Test mode New test mode

(Example) Power Off Power On In-play Error Production

BAND To power on To power off – Time/Err.No. switching

(offset adjustment performed)

] – FWD-Kick FF/TR+ –

[ – REV-Kick REV/TR- –

1 – T.Close (AGC performed) Scan –

/parameter display switching

2 – T.BAL adjustment Mode –

/T.Open

3 To power on F.Close/RF AGC/AGC – –

(offset adjustment not performed)

6 – Mode switching Auto/Manu –

/T.Close (no AGC)/Jump switching

Note: Eject and CD on/off is performed in the same procedure as that for the normal mode.

(3) Cause of Error and Error Code

Code Class Contents Description and cause

40 Electricity Off focus detected. FOK goes low.

→ Damages/stains on disc, vibrations or failure on servo.

41 Electricity Spindle unlocked. FOK = Low continued for 50 msec.


42 Electricity Sub-code unreadable. Sub-code was unreadable for 50 msec.


43 Electricity Sound skipping detected. Last address memory function was activated.


Note: Mechanical errors during aging are not displayed.

The error codes should be indicated in the same way as in the normal mode.

47

DEH-2130R,2100R

(4) Display of Operational Status (CPOINT) during SetupStatus No. Contents Protective action01 Carriage move to home position started. None02 Carriage is moving toward inner diameter. Specified 10 seconds has been passed or failure

on home switch.03 Carriage is moving toward outer diameter. Specified 10 seconds has been passed or failure

on home switch.05 Carriage outer diameter feed (1 second) in progress. None11 Setup started. None12 Spindle rotation and focus search started. None13 Waiting for focus close (XSI=Low). Specified focus search time has been passed.14 Waiting for focus close (FOK=High). (After AGC) Specified focus search time has been passed.15 Waiting for focus close (FOK=High). (Before AGC) Specified focus search time has been passed.16 Rough AGC in progress. Off focus.17 Setup (1/2) before T balance adjustment is started. Off focus.18 Setup (2/2) before T balance adjustment is started. Off focus.24 T balance adjustment (1/2). Off focus.25 T balance adjustment (2/2). Off focus.26 Standing by after spindle rough servo is over. Off focus.27 Setup before RF AGC (first) is started. Off focus.28 RF AGC (first) in progress. Off focus.29 Setup before RF AGC (second) is started. Off focus.30 RF AGC (second) in progress. Off focus.31 Tracking close in progress. Off focus.32 Standing by after tracking is closed. Off focus.33 Focus AGC started. Off focus.34 Focus AGC in progress. Tracking AGC started. Off focus.35 Tracking AGC in progress. Off focus.

Spindle processes applicable servo.36 Check of MIRR and LOCK pin. RF AGC in progress. Off focus. Spindle not locked.

CRG close in progress. Check of sub-code. Sub-code unreadable.

(5) Display Examples

1) During Setup (When status no. = 11)

TRK No. MIN. SEC.

11 11' 11"

2) During Operation (TOC read, TRK search, Play, FF and REV)

The same as in the normal mode.

3) When a Protection Error Occurred

Switch to the following displays (A) and (B) using the [BAND] switch:

(A) Error occurrence timing display in absolute time.

An example: Error occurred in 12th tune at 34'56" in absolute time.

TRK No. MIN. SEC.

12 34' 56"

(B) Error No. display

An example: Error #40 (Off focus is detected)

ERROR-40

48

DEH-2130R,2100R

7.1.2 DISASSEMBLY

- Removing the Tuner Amp Assy

Remove the two screws (Fig.2).

Remove the three screws and then remove

the Cover (Fig.2).

Remove the screw (Fig.3).

Disconnect the four claws and then remove

the Tuner Amp Assy (Fig.3).

- Removing the Upper Case (not shown)

- Removing the CD Mechanism Module (Fig.1)

Remove the four screws.

Disconnect the connector and then remove the CD

Mechanism Module (not shown).

- Removing the Panel Assy (not shown)

1.Disconnect the two stoppers and then remove the

Panel Assy.

Fig.1

Fig.2

Fig.3Tuner Amp Assy

Cover

CD Mechanism Module

49

DEH-2130R,2100R

- Removing the Upper Frame

1. Remove six Springs A, two Springs B and four

Screws.

2. Remove two Tabs situated on rear side of the Upper

Frame, remove two Arms on the front side, then

remove two Tabs on the front side.

- Removing the Carriage Mechanism

1. Disengage the Carriage Mechanism from the two

dampers situated in the front side by driving it up,

then disengage and remove the mechanism from the

one damper by driving it up aslant into front side

direction.

Note : When assembling the Carriage Mechanism, coat

the dampers with alcohol prior to the assembly.

- Removing the Clamp Arm Assy

1. Remove a Spring A, a B and a Spring C.

2. Drive the Clamp Arm Assy up into rear side direction,

then disengage the arm from its current position

Finally, drive the assembly approximately 45 degrees

upward, then slide the assembly toward right side to

remove it.

B

A

B A

A

A

Arm

Arm

A

B

C

Upper Frame

Carriage Mechanism Section

Clamp Arm Assy Section

A

A

50

DEH-2130R,2100R

- Removing the Guide Arm Assy

1. Remove a connector, a spring A and B

2. Drive the Guide Arm Assy up aslant into rear side

direction, then remove it from a Pin. Finally, drive the

assembly approximately 45 degrees upward, then

slide the assembly toward left side to remove it.

Note : When assembling the guide arm assembly, route

the cord inside the assembly. In this operation,

care must be exercised so that cord may be

caught by the gear.

- Removing the LO Arm Assy

1. Remove two Pins to dismount the LO Arm Assy.

- Removing the Control Unit and the Spindle

Motor

1. Remove from the connector after mounting the short

pin on the flexible PCB of the pickup unit.

2. Remove two Soldered joints, then remove two

Screws A.

3. Remove two connectors and a Screw B.

4. Disengage the Control Unit from two Tabs, then dis-

mount the unit by sliding it toward left.

5. Dismount the Spindle Motor.

A

Guide Arm Assy Section

B

Pin

LO Arm Assy Section

Spindle Motor

A A

Control Unit

Short Pin

B

51

DEH-2130R,2100R

- Removing the Loading Motor and Carriage

Motor

1. Remove the Spring and two Screws A.

2. Dismount the Loading Motor.

3. Remove the Belt, a Screw B, two Screws C, a Guide

and a Screw Unit.

4. Dismount the Carriage Motor.

Note : When assembling the Belt, use care so that it

may not be contaminated by grease.

- Removing the Pickup Unit

1. Remove two Screws and a Shaft.

2. Dismount the Pickup Unit.

Pickup Unit

Shaft

CGuide

B

Screw Unit Carriage Motor

AA

CBelt

Loading Motor

52

DEH-2130R,2100R

7.2 PARTS

7.2.1 IC

- Pin Functions(PE5090A)Pin No. Pin Name I/O Format Function and Operation

1 MODEL1 I Model select input2 NL1 I Noise level input3 NL2DT I Noise level input 24 AVSS A/D GND5 ST I Stereo input6 SD I SD signal input 7 AREF1 (D/A converter standard voltage)8 KYDT I Key data input9 DPDT O C Key data output

10 SDBW I SDBW input11 TUNPDI I PLL IC data input12 TUNPDO O C PLL IC data output13 TUNPCK O C PLL IC clock output14 TUNPCE O C PLL IC chip enable output15 CURRQ O C Tuner voltage FIX output16 XSI I C LSI data input17 XSO O C LSI data output18 XSCK O C LSI clock output19 DRST O C RDS decoder reset output20 ADPW O C A/D converter power output21 FM/AM O C FM/AM power select output22 VDCONT O C VD power control output23 CONT O C Servo driver power control output24 XAO O C CD LSI data discernment control signal output25 XRST O C CD LSI reset output26 XSTB O C CD LSI strobe output27 CLAMP I Disc clamp sense input28 MIRR I Mirror detection input 29 FOK I Focus OK signal input30 LOCK I Spindle lock detector input31 CDLOAD O C LOAD motor loading control output32 TELIN I Cellular mute input33 VSS GND34 CDEJECT O LOAD motor eject control output35 CD5VON O C CD +5V power supply control output

36–39 NC Not used40 RECIEVE O C RDS decoder receiving output41 SWVDD O C Grille power supply control output42 SYSPW O C System power supply control output43 NC Not used44 MUTE O C Mute output45 PEE O C Beep tone output46 LOCH O C LOCH output47 RDS57K I 57kHzBP-OUT sense input48 TUNPCE2 O C EEPROM chip enable output 249 NC Not used50 VCK O C Clock output for electronic volume51 VDT O C Data output for electronic volume52 ANTPW O C Antenna power output53 VST O C Strobe pulse output for electronic volume

54–57 DEQ4-1 O C Direct EQ data output 4-158 RDSLK I RDS LK signal input59 RDT I RDS data input60 RESET Reset

53

DEH-2130R,2100R

Pin No. Pin Name I/O Format Function and Operation61 LDET I PLL lock sense input62 RCK I RDS clock input63 ASENS I ACC power sense input64 BSENS I Back up power sense input65 DSENS I Grille detach sense input66 TMUTE O C Tuner mute output67 LOCL O C LOC L output68 VDD Power supply69 X2 Crystal oscillator connection pin70 X1 Crystal oscillator connection pin71 IC GND72 NC Not used73 TESTIN I Test program mode input74 AVDD Positive power supply terminal for analog circuit75 AVREF0 GND76 SL I Signal level input77 TEMP I Temperature detector input78 VDSENS I Over voltage sense input79 DSCSNS I Disc detect input80 EJTSNS I Disc EJECT position detect input

801

20

21 40

41

60

61

*PE5090A

Output Format MeaningC C MOS output

IC's marked by* are MOS type.

Be careful in handing them because they are very liable

to be damaged by electrostatic induction.

S-80834ANY

1 2 31

OUT VDD VSS

54

DEH-2130R,2100R

SN761029DL

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

VC

CA

Vcc

IN1-

RIN

1-L

IN2-

RIN

2-L

IN3-

RIN

3-L

IN4(

+)-R

IN4(

+)-L

IN4(

-)-R

IN4(

-)-L

AG

ND

AG

ND

SW

ou

t-R

SW

ou

t-L

ZC

in-R

ZC

in-L

LOU

D-R

LOU

D-L

VR

in-R

VR

in-L

TR

EB

-RT

RE

B-L

BA

SS

-C1-

RB

AS

S-C

1-L

BA

SS

-R-R

BA

SS

-R-L

BA

SS

-C2-

RB

AS

S-C

2-L

NC

NC

TO

NE

ou

t-R

TO

NE

ou

t-L

FAD

ER

in-R

FAD

ER

in-L

FRN

To

ut-

RFR

NT

ou

t-L

RE

AR

ou

t-R

RE

AR

ou

t-L

DV

ccV

RE

Fin

DA

TA

AG

ND

CLK

DG

ND

ST

BC

t

3 Line Serial Bus

Bass Treble Volume,Loudness Fader

GainAdjust

Isolator

Zero-crossDetector

PowerSupply

Bass Treble Volume,Loudness

Fader

GainAdjust

Isolator

PowerSupply

A

A

PM4009A

55

DEH-2130R,2100R

BR9010FV

NC

VCC

CS

SK

WC

GND

DO

DI

1

2

3

4

8

7

6

5

CSSKDIDOWC

: Chip select input: Serial data clock input: Serial data input: Serial data output: Write control input

- Pin Functions (PD6293A)Pin No. Pin Name I/O Function and Operation

1-5 SEG4-0 O LCD segment output6-9 COM3-0 O LCD common output 10 VLCD LCD drive power supply

11-14 KST3-0 O Key strobe output15,16 KDT0,1 I Key data input (analogue input)

17 REM I Remote control reception18 DPDT I Display data input19 NC Not used20 KYDT O Key data output21 MODA GND22 X0 Crystal oscillator connection pin23 X1 Crystal oscillator connection pin24 VSS GND

25,26 KDT2,3 I Key data input27 NC Not used28 KST4 O Key strobe output

29-32 NC Not used33-55 SEG35-13 O LCD segment output

56 VDD Power supply57-64 SEG12-5 O LCD segment output

*PD6293A

49

4833

32

17

16 1

64

56

DEH-2130R,2100R

- Pin Functions (UPD63711GC)Pin No. Pin Name I/O Function and Operation

1 D.GND Logic circuit GND2 RFOK O RFOK signal output3 rst I Reset signal input4 A0 I Command/parameter identification signal input5 stb I Data strobe signal input6 sck I Clock signal input for serial data input/output7 SO O Serial data and status signal output8 SI I Serial data input9 xtalen I Crystal oscillation control pin

10 D.VDD Positive power supply terminal to logic circuit11 DA.VDD Positive power supply terminal to D/A converter12 R_OUT O Right channel audio output signal13 DA.GND D/A converter GND14 REGC I The outside putting capacitor connection pin for SCF regulator15 DA.GND D/A converter GND16 L_OUT O Left channel audio output signal17 DA.VDD Positive power supply terminal to D/A converter18 R+ O Right channel audio data output19 R- O Right channel audio data output20 L- O Left channel audio data output21 L+ O Left channel audio data output22 X.VDD Positive power supply terminal to crystal oscillation circuit23 XTAL I Crystal oscillator connect pin24 xtal O Crystal oscillator connect pin25 X.GND Crystal oscillation circuit GND26 D.VDD Positive power supply terminal to logic circuit27 EMPH O Output pin for the pre-emphasis data in the sub-Q code28 FLAG O Flag output pin to indicate that audio data currently being output consists

of noncorrectable data29 DIN I Serial data input to internal DAC30 DOUT O Serial audio data output31 SCKIN I Serial clock input to internal DAC32 SCKO O Audio data that is output from DOUT changes at rising edge of this clock33 LRCKIN I LRCK signal input to internal DAC34 LRCK O Signals to distinguish the right and left channels of the audio data output

from DOUT35 HOLD O Defect detection output36 TX O Digital audio interface data output37 D.GND Logic circuit GND38 C16M O Oscillator clock buffering output39 LIMIT I Status of the pin is output at Bit 5 of the status output40 D.VDD Positive power supply terminal to logic circuit41 LOCK O EFM synchronous detection signal42 RFCK O Frame synchronous signal of XTAL-system43 MIRR O MIRR output44 PLCK O Monitor pin of bit clock45 D.GND Logic circuit GND46 C1D1 O Output pin for indicating the C1 error correction results47 C1D2 O Output pin for indicating the C1 error correction results48 C2D1 O Output pin for indicating the C2 error correction results49 C2D2 O Output pin for indicating the C2 error correction results50 C2D3 O Output pin for indicating the C2 error correction results51 D.VDD Positive power supply terminal to logic circuit52 PACK O CD-TEXT PACK synchronous signal53 TSO O CD-TEXT data serial output54 TSI I CD-TEXT control parameter serial input55 tsck I CD-TEXT serial clock input56 TSTB I CD-TEXT parameter strobe signal input57 D.GND Logic circuit GND

57

DEH-2130R,2100R

Pin No. Pin Name I/O Function and Operation58 TEST0 I Test pin59 TEST1 I Test pin60 ATEST O Test pin61 A.GND Analog circuit GND62 FD O Focus drive output63 TD O Tracking drive output64 SD O Sled drive output65 MD O Spindle drive output66 DAC0 O DAC output for adjustment67 DAC1 O DAC output for adjustment68 DAC2 O DAC output for adjustment69 DAC3 O DAC output for adjustment70 A.VDD Positive power supply terminal to analog circuit71 EFM O EFM signal output72 ASY I EFM comparator reference voltage input73 C3T 3T detection capacitor additional pin74 RFI I RF signal input for EFM data regulation75 AGCO O RF signal output of after gain adjustment 76 AGCI I RF-AGC amplifier input77 RFO O RF summing amplifier output78 EQ2 RF amplifier equalizer parts additional pin79 EQ1 RF amplifier equalizer parts additional pin80 RF- I RF summing amplifier inverted input81 A.GND Analog circuit GND82 A I Photo detector A input83 C I Photo detector C input84 B I Photo detector B input85 D I Photo detector D input86 F I Photo detector F input87 E I Photo detector E input88 A.VDD Positive power supply terminal to analog circuit89 REFOUT O Reference electric potential output90 FE- I Focus error amplifier inverted input91 FEO O Focus error amplifier output92 TE- I Tracking error amplifier inverted input93 TEO O Tracking error amplifier output94 TE2 O Tracking error output of after amplification95 TEC I Tracking comparator input96 A.GND Analog circuit GND97 PD I PD detection signal input for LD output monitor 98 LD O LD control current output99 PN I APC circuit control polarity set pin

100 A.VDD Positive power supply terminal to analog circuit

20

21

40

41 60

61

80

1

100

76

26

125

7551

50

*UPD63711GC

58

DEH-2130R,2100R

- Pin Functions (BA5985FM)Pin No. Pin Name I/O Function and Operation

1 FWD I Loading driver FWD input2 OPIN1(+) I CH1 pre-amplifier input3 OPIN1(−) I CH1 pre-amplifier inverted input4 OPOUT1 O CH1 pre-amplifier output5 OPIN2(+) I CH2 pre-amplifier input6 OPIN2(−) I CH2 pre-amplifier inverted input7 OPOUT2 O CH2 pre-amplifier output8 VCC Power supply9 VOL(−) O Loading driver negative output

10 VOL(+) O Loading driver positive output11 VO2(−) O Driver CH2 negative output12 VO2(+) O Driver CH2 positive output13 VO1(−) O Driver CH1 negative output14 VO1(+) O Driver CH1 positive output15 VO4(+) O Driver CH4 positive output16 VO4(−) O Driver CH4 negative output17 VO3(+) O Driver CH3 positive output18 VO3(−) O Driver CH3 negative output19 GND GND20 BIAS I Bias input21 MUTE Mute control22 OPOUT3 O CH3 pre-amplifier output23 OPIN3(−) I CH3 pre-amplifier inverted input24 OPIN3(+) I CH3 pre-amplifier input25 OPOUT4 O CH4 pre-amplifier output26 OPIN4(−) I CH4 pre-amplifier inverted input27 OPIN4(+) I CH4 pre-amplifier input28 REV I Loading driver REV input

BA5985FM

59

DEH-2130R,2100R

7.2.2 DISPLAY

- CAW1559

CO

MM

ON

SE

GM

EN

T

60

DEH-2130R,2100R

7.3 OPERATIONAL FLOW CHART

VDD=5V68pin

Power ON

L

L

YES

L

bsens66pin

asens65pin

dsens63pin

ADPW←H20pin

swvdd←L41pin

Source keys operative

To each source's flow chart

SYSPW←H42pin

Starts communication with Grille microcomputer.

Source ON

300ms

300ms

In case of the above signal, the communication with Grille microcomputer may fail.If the time interval is not 300msec, the oscillator may be defective.

61

DEH-2130R,2100R

8. OPERATIONS AND SPECIFICATIONS

8.1 OPERATIONS

+/– button EJECT button

Buttons 1–6

TA/AF button

LOCAL/BSM button

AUDIO button

BAND buttonDisc Loading Slot

PTY button

Detach button

SOURCE/OFF button

DISP button

5/∞/2/3 buttons

62

DEH-2130R,2100RB

asic

Ope

ratio

n

To L

iste

n to

Mus

icT

he f

ollo

win

g ex

plai

ns th

e in

itial

ope

ratio

ns r

equi

red

befo

re y

ou c

an li

sten

to m

usic

.

Not

e:•

Loa

ding

a d

isc

in th

is p

rodu

ct.

1.Se

lect

the

des

ired

sou

rce

(e.g

. Tun

er).

Eac

h pr

ess

of th

e SO

UR

CE

/OFF

but

ton

sele

cts

the

desi

red

sour

ce in

the

follo

win

g or

der:

Bui

lt-in

CD

pla

yer

=T

uner

Not

e:•

Whe

n no

dis

c is

set

in th

is p

rodu

ct, b

uilt-

in C

D p

laye

r so

urce

will

not

cha

nge.

•W

hen

this

pro

duct

’s b

lue/

whi

te le

ad is

con

nect

ed to

the

car’

s A

uto-

ante

nna

rela

y co

ntro

l ter

min

al,

the

car’

s A

uto-

ante

nna

exte

nds

whe

n th

is p

rodu

ct’s

sou

rce

is s

witc

hed

ON

. To

retr

act t

he a

nten

na,

switc

h th

e so

urce

OFF

.

2.R

aise

or

low

er t

he v

olum

e.

3.Tu

rn t

he s

ourc

e O

FF.

Hol

d fo

r 1

seco

nd

Eac

h pr

ess

chan

ges

the

Sour

ce ..

.

Bas

ic O

pera

tion

of T

uner

Man

ual a

nd S

eek

Tuni

ng

•Y

ou c

an s

elec

t th

e tu

ning

met

hod

by c

hang

ing

the

leng

th o

f ti

me

you

pres

s th

e 2

/3bu

tton

.

Man

ual T

unin

g (s

tep

by s

tep)

0.5

seco

nds

or le

ss

Seek

Tun

ing

0.5

seco

nds

or m

ore

Not

e:•

If y

ou c

ontin

ue p

ress

ing

the

butto

n fo

r lo

nger

than

0.5

sec

onds

, you

can

ski

p br

oadc

ast

stat

ions

. See

k T

unin

g st

arts

as

soon

as

you

rele

ase

the

butto

n.•

Ster

eo in

dica

tor

“”

light

s w

hen

a st

ereo

sta

tion

is s

elec

ted.

Pres

et T

unin

g

•Y

ou c

an m

emor

ize

broa

dcas

t st

atio

ns in

but

tons

1 t

hrou

gh 6

for

easy

, one

-tou

ch s

tati

on r

ecal

l.

Pres

et s

tatio

n re

call

2 se

cond

s or

less

Bro

adca

st s

tatio

n pr

eset

mem

ory

2 se

cond

s or

mor

e

Not

e:•

Up

to 1

2 FM

sta

tions

(6

in F

1 (F

M1)

and

F2

(FM

2))

and

6 M

W/L

W s

tatio

ns c

an b

est

ored

in m

emor

y.•

You

can

als

o us

e th

e 5

or ∞

butto

ns to

rec

all b

road

cast

sta

tions

mem

oriz

ed in

but

tons

1th

roug

h 6.

Pres

et N

umbe

r Ind

icat

orB

and F1

(FM

1)

=F2

(FM

2)

=M

W/L

WB

and

Indi

cato

r

Freq

uenc

y In

dica

tor

Thi

s pr

oduc

t’s A

F fu

nctio

n ca

n be

sw

itche

d O

N a

nd O

FF. A

F sh

ould

be

switc

hed

OFF

for

norm

al tu

ning

ope

ratio

ns.

63

DEH-2130R,2100R

Bas

ic O

pera

tion

Bas

ic O

pera

tion

of B

uilt-

in C

D P

laye

r

Trac

k N

umbe

r Ind

icat

or Play

Tim

e In

dica

tor

Ejec

t Not

e:•

The

CD

fun

ctio

n ca

n be

turn

ed O

N/O

FFw

ith th

e di

sc r

emai

ning

in th

is p

rodu

ct.

• A

dis

c le

ft p

artia

lly in

sert

ed a

fter

eje

ctio

nm

ay in

cur

dam

age

or f

all o

ut.

Trac

k Se

arch

and

Fas

t For

war

d/Re

vers

e

•Y

ou c

an s

elec

t be

twee

n T

rack

Sea

rch

or F

ast

For

war

d/R

ever

se b

y pr

essi

ngth

e 2

/3bu

tton

for

a d

iffe

rent

leng

th o

f ti

me.

Tra

ck S

earc

h0.

5 se

cond

s or

less

Fast

For

war

d/R

ever

se

Con

tinue

pre

ssin

g

Not

e:•

If a

dis

c ca

nnot

be

inse

rted

ful

ly o

r pl

ayba

ck f

ails

, mak

e su

re th

e re

cord

ed s

ide

is d

own.

Push

the

EJE

CT

but

ton

and

chec

k th

e di

sc f

or d

amag

e be

fore

rei

nser

ting

it.•

If a

dis

c is

inse

rted

with

the

reco

rded

sid

e up

, it w

ill b

e ej

ecte

d au

tom

atic

ally

aft

er a

few

mom

ents

.•

If th

e bu

ilt-i

n C

D p

laye

r ca

nnot

ope

rate

pro

perl

y, a

n er

ror

mes

sage

(su

ch a

s “E

RR

OR

-14”

)ap

pear

s on

the

disp

lay.

Dis

c Lo

adin

g Sl

ot

Not

e:•

The

bui

lt-in

CD

pla

yer

play

s on

e st

anda

rd 1

2 cm

or

8 cm

(si

ngle

) C

D a

t a ti

me.

Do

not u

se a

n ad

apte

rw

hen

play

ing

8 cm

CD

.

Aud

io A

djus

tmen

t

Ente

ring

the

Aud

io M

enu

With

this

Men

u, y

ou c

an a

djus

t the

sou

nd q

ualit

y.

Not

e:•

Aft

er e

nter

ing

the

Aud

io M

enu,

if y

ou d

o no

t per

form

an

oper

atio

n w

ithin

abo

ut 3

0 se

cond

s, th

eA

udio

Men

u is

aut

omat

ical

ly c

ance

led.

1.Se

lect

the

des

ired

mod

e in

the

Aud

io M

enu.

2.O

pera

te a

mod

e.

3.C

ance

l the

Aud

io M

enu.

Eac

h pr

ess

chan

ges

the

Mod

e ...

64

DEH-2130R,2100RA

udio

Adj

ustm

ent

Aud

io M

enu

Func

tions

The

Aud

io M

enu

feat

ures

the

follo

win

g fu

nctio

ns.

Bal

ance

Adj

ustm

ent(

FAD

)T

his

func

tion

allo

ws

you

to s

elec

t a F

ader

/Bal

ance

set

ting

that

pro

vide

s id

eal l

iste

ning

con

-di

tions

in a

ll oc

cupi

ed s

eats

.

1.P

ress

the

AU

DIO

but

ton

and

sele

ct t

he F

ader

/Bal

ance

mod

e (F

AD

) in

the

Aud

io M

enu.

Not

e:•

“FA

D 0

” is

the

prop

er s

ettin

g w

hen

2 sp

eake

rs a

re in

use

.

Bas

s A

djus

tmen

t (B

AS)

You

can

adj

ust a

Bas

s le

vel a

s de

sire

d.

1.P

ress

the

AU

DIO

but

ton

and

sele

ct t

he B

ass

mod

e (B

AS)

in t

he A

udio

Men

u.

2.B

oost

or

atte

nuat

e th

e ba

ssle

vel w

ith

the

55/∞∞

butt

ons.

The

dis

play

sho

ws

“+6”

– “

–6”.

3.A

djus

t le

ft/r

ight

spe

aker

bal

-an

ce w

ith

the

22/33

butt

ons.

“BA

L L

9” –

“B

AL

R9”

is d

ispl

ayed

as it

mov

es f

rom

left

to r

ight

.

2.A

djus

t fr

ont/

rear

spe

aker

bal

-an

ce w

ith

the

55/∞∞

butt

ons.

“FA

DF1

5” –

“FA

D R

15”

is d

is-

play

ed a

s it

mov

es f

rom

fro

nt to

rear

.

Treb

le A

djus

tmen

t (TR

E)Y

ou c

an a

djus

t a T

rebl

e le

vel a

s de

sire

d.

1.P

ress

the

AU

DIO

but

ton

and

sele

ct t

he T

rebl

e m

ode

(TR

E)

in t

he A

udio

Men

u.

Loud

ness

Adj

ustm

ent (

LOU

D)

The

Lou

dnes

s fu

nctio

n co

mpe

nsat

es f

or d

efic

ienc

ies

in th

e lo

w a

nd h

igh

soun

d ra

nges

at

low

vol

ume.

1.P

ress

the

AU

DIO

but

ton

and

sele

ct t

he L

oudn

ess

mod

e (L

OU

D)

in t

he A

udio

Men

u.

“LO

UD

”

2.Sw

itch

the

Lou

dnes

s fu

ncti

onO

N/O

FF

wit

h th

e 55

/∞∞bu

t-to

ns.

2.B

oost

or

atte

nuat

e th

e tr

eble

leve

l wit

h th

e 55

/∞∞bu

tton

s.T

he d

ispl

ay s

how

s “+

6” –

“–6

”.

65

DEH-2130R,2100R

+ ≠

+ ≠

Not

e:D

epen

ding

on

the

kind

of

vehi

cle,

the

func

-tio

n of

3*

and

5* m

ay b

e di

ffer

ent.

If th

is is

the

case

, be

sure

to c

onne

ct 2

* to

5*

and

4* to

5.

4*5*3*

1*

2*

1. T

his

prod

uct

2. R

ear

outp

ut

3. A

nten

na ja

ck

6. C

onne

ct le

ads

of th

e sa

me

colo

r to

eac

h ot

her.

7. C

ap (

1*)

Whe

n no

t usi

ng th

is te

rmin

al,

do n

ot r

emov

e th

e ca

p.

8. Y

ello

w (

3*)

Bac

k-up

(or

acce

ssor

y)

9. Y

ello

w (

2*)

To te

rmin

al a

lway

s su

pplie

dw

ith p

ower

reg

ardl

ess

ofig

nitio

n sw

itch

posi

tion.

10. R

ed (

5*)

Acc

esso

ry(o

r ba

ck-u

p)

11. R

ed (

4*)

To e

lect

ric

term

inal

con

-tr

olle

d by

igni

tion

switc

h (1

2 V

DC

) O

N/O

FF.

19. F

use

hold

er

12. B

lack

(gr

ound

)To

veh

icle

(m

etal

) bo

dy.

13. I

SO c

onne

ctor

Not

e:In

som

e ve

hicl

es, t

he I

SO c

onne

ctor

may

be d

ivid

ed in

to tw

o. I

n th

is c

ase,

be

sure

to c

onne

ct to

bot

h co

nnec

tors

.

18. Y

ello

w/b

lack

If y

ou u

se a

cel

lula

r te

leph

one,

con

nect

it v

iath

e A

udio

Mut

e le

ad o

n th

e ce

llula

r te

leph

one.

If n

ot, k

eep

the

Aud

io M

ute

lead

fre

e of

any

conn

ectio

ns.

17. F

use

resi

stor

14. S

peak

er le

ads

Whi

te: F

ront

left

+W

hite

/bla

ck: F

ront

left

≠G

ray

: Fro

nt r

ight

+G

ray/

blac

k: F

ront

rig

ht ≠

Gre

en: R

ear

left

+G

reen

/bla

ck: R

ear

left

≠V

iole

t: R

ear

righ

t +V

iole

t/bla

ck: R

ear

righ

t ≠

22. B

lue/

whi

te (

6*)

23. B

lue/

whi

te (

7*)

To A

uto-

ante

nna

rela

y co

ntro

l ter

min

al.

(Max

. 300

mA

12 V

DC

.)

24. The

pin

pos

ition

of

the

ISO

con

nect

or w

ill d

iffe

rde

pend

s on

the

type

of

vehi

cle.

Con

nect

6*

and

7*w

hen

Pin

5 is

an

ante

nna

cont

rol t

ype.

In

anot

her

type

of

vehi

cle,

nev

er c

onne

ct 6

* an

d 7*

.

26. P

erfo

rm th

ese

conn

ectio

ns w

hen

usin

ga

diff

eren

t am

p (s

old

sepa

rate

ly).

25. R

ear

spea

ker

25. R

ear

spea

ker

21. S

yste

m r

emot

e co

ntro

l

20. B

lue/

whi

teTo

sys

tem

con

trol

term

inal

of

the

pow

er a

mp.

(Max

. 300

mA

12 V

DC

.)

15. C

onne

ctin

g co

rds

with

R

CA

pin

plug

s (s

old

sepa

rate

ly)

16. P

ower

am

p (s

old

sepa

rate

ly)

4. F

use

DEH-2130R,2100R

8.2 SPECIFICATIONS

GeneralPower source .......... 14.4 V DC (10.8 – 15.1 V allowable)Grounding system ........................................ Negative typeMax. current consumption ...................................... 10.0 ADimensions

(mounting size) ...... 178 (W) × 50 (H) × 159 (D) mm(front face) .............. 188 (W) × 58 (H) × 19 (D) mm

Weight ...................................................................... 1.4 kg

AmplifierMaximum power output ...................................... 40 W × 4Continuous power output .................................... 22 W × 4

(DIN45324, +B = 14.4 V)Load impedance .......................... 4 Ω (4 – 8 Ω allowable)Preout maximum output level/output impedance

................................................................ 2.2 V /1 kΩTone controls

(Bass) .............................................. ±12 dB (100 Hz)(Treble) ............................................ ±12 dB (10 kHz)

Loudness contour.......... +10 dB (100 Hz), +7 dB (10 kHz)(volume: –30 dB)

CD playerSystem .................................... Compact disc audio systemUsable discs .................................................. Compact discSignal format...................... Sampling frequency: 44.1 kHz

Number of quantization bits: 16; linearFrequency characteristics................ 5 – 20,000 Hz (±1 dB)Signal-to-noise ratio ........ 94 dB (1 kHz) (IEC-A network)Dynamic range ............................................ 92 dB (1 kHz)Number of channels ............................................ 2 (stereo)

FM tunerFrequency range ...................................... 87.5 – 108 MHzUsable sensitivity

.................. 11 dBf (1.0 µV/75 Ω, mono, S/N: 30 dB)50 dB quieting sensitivity .... 16 dBf (1.7 µV/75 Ω, mono)Signal-to-noise ratio ...................... 70 dB (IEC-A network)Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)Frequency response ...................... 30 – 15,000 Hz (±3 dB)Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)

MW tunerFrequency range ........................ 531 – 1,602 kHz (9 kHz)Usable sensitivity .............................. 18 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)

LW tunerFrequency range ........................................ 153 – 281 kHzUsable sensitivity .............................. 30 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)

Note:• Specifications and the design are subject to possi-

ble modification without notice due to improve-ments.

CRT2434 DEH-2130R HIGH POWER CD PLAYER …diagramas.diagramasde.com/otros/Pioneer_DEH-2130R,2100.pdf · model part no. language deh-2130r/x1m/ew crd3137 english, ... unit focus act

Documents