This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Upflow/ Horizontal Downflow /Horizontal Condensing, Direct Vent Gas-Fired Furnace
NATURAL GAS MODELSCentral Heating furnace designs are certified to ANSI Z21.47 / CSA 2.3 for both natural and L.P. gas. Limit setting and rating data were established and approved under standard rating condi-tions using American National Stan-dards Institute standards.
SAFE OPERATIONThe Integrated System Control has solid state devices, which continuously monitor for presence of flame, when the system is in the heating mode of operation. Dual solenoid combination gas valve and regulator provide extra safety.
QUICK HEATINGDurable, cycle tested, heavy gauge alu-minized steel heat exchanger quickly transfers heat to provide warm condi-tioned air to the structure. Low energy power vent blower, to increase effi-ciency and provide a positive discharge of gas fumes to the outside.
BURNERSMultiport Inshot burners will give years of quiet and efficient service. All models can be converted to L.P. gas without changing burners.
INTEGRATED SYSTEM CONTROLExclusively designed operational pro-gram provides total control of furnace limit sensors, blowers, gas valve, flame control and includes self diagnostics for ease of service. Also contains connec-tion points for E.A.C./humidifier.
AIR DELIVERYThe four speed, direct drive blower motor, has sufficient airflow for most heating and cooling requirements, will switch from heating to cooling speeds on demand from room thermostat. The blower door safety switch will prevent or terminate furnace operation when the blower door is removed.
STYLINGHeavy gauge steel and “wrap-around” cabinet construction is used in the cabinet with baked-on enamel finish for strength and beauty. The heat exchang-er section of the cabinet is completely lined with foil faced fiberglass insulation. This results in quiet and efficient opera-tion due to the excellent acoustical and insulating qualities of fiberglass. Built-in bottom pan and alternate bottom, left or right side return air connection provision.
FEATURES AND GENERAL OPERATIONThe XT95 High Efficiency Gas Furnaces employ a Silicon Nitride Hot Surface Ignition system, which eliminates the waste of a constant burning pilot. The integrated system control lights the main burners upon a demand for heat from the room thermostat. Complete front service access.
a. Low energy power venter
b. Vent proving pressure switch.
Features and Benefits
XT95 Standard Equipment• Powersupply115/1/60
• Convertibletohorizontalwithleftofright airflow
• Type 29-4C™ stainless steel second-ary heat exchanger
• Innerblowerdoors
• ConstanttorqueECMblowermotor
• SiliconNitrideigniterwithadaptiveheat up
• Accessoryhook-upcapability– Hum and EAC
• Quietinduceddraftblower
• Blowerdoorsafetyswitch
• Dualsolenoidcombinationgasvalve®ulator
• PVCventing–1or2pipeventoption
• Left/rightgasconnection
• Selectablecoolingfanoffdelayelimi-nates need for BAY24X045 time delay relay
• Singlewiretwinning
• Integratedsolidstatecontrolwithself-diagnostics
• 24voltfuse
• Manualresetburnerboxlimit
• Optional extended warranties
22-1859-01 3
Contents
General Features 2Features and Benefits 2
XT95 Standard Equipment 2XT95 Optional Equipment 4
General Data 5TUH1B040A9H21A 5TUH1B060A9H31A 5TUH1B080A9H31A 5TUH1C100A9H41A 6TUH1D120A9H51A 6TDH1B040A9H21A 7TDH1B065A9H31A 7TDH1C085A9H41A 7TDH1D110A9H51A 7
Performance Data 8Electrical Data 10Field Wiring 14Twinning Field Wiring 15Dimensions 16
1 Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3.2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea
level. For Canadian applications, above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above
sea level.3 Based on U.S. government standard tests.4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.5 Constant torque ECM blower motor6 Refer to the Vent Length Table in the Installer's Guide or the Allowable Vent Length label located on the furnace.7 All TUH1 and TDH1 furnace models have a vent outlet diameter that equals 2".8 4 Speed, direct drive X13 style high efficiency DC motor
TUH1B040A9H21AUpflow/Horizontal
40,00038,000
9530-60
DIRECT10 x 7
14
See Fan Performance Table1/2
1075115/1/60
CentrifugalDirect - 1
1/55 - 3000115/1/60
1.00Yes
High Velocity1 - 17x25 - 1in.
2 Round
Alum. Steel
20
2—452—56
Redundant - Single Stage
Hot Surface IgnitionMultiport Inshot
2115/1/60
9.7151/2
H x W x D41-3/4 x 19-1/2 x 30-1/2
139 / 129
TUH1B060A9H31AUpflow/Horizontal
60,00057,000
9530-60
DIRECT10 x 7
14
See Fan Performance Table1/2
1075115/1/60
CentrifugalDirect - 1
1/15 - 3450115/1/60
1.75Yes
High Velocity1 - 17x25 - 1in.
2 Round
Alum. Steel
20
3—453—56
Redundant - Single Stage
Hot Surface IgnitionMultiport Inshot
3115/1/60
10.4151/2
H x W x D41-3/4 x 19-1/2 x 30-1/2
150 / 140
TUH1B080A9H31AUpflow/Horizontal
80,00076,000
9535-65
DIRECT10 x 8
14
See Fan Performance Table1/2
1075115/1/60
CentrifugalDirect - 1
1/20 - 3450115/1/60
0.71Yes
High Velocity1 - 17x25 - 1in.
3 Round
Alum. Steel
20
4—454—56
Redundant - Single Stage
Hot Surface IgnitionMultiport Inshot
4115/1/60
9.4151/2
H x W x D41-3/4 x 19-1/2 x 30-1/2
158 / 148
6 22-1859-01
General Data
TUH1D120A9H51AUpflow/Horizontal
110,000104,500
9540 - 70
DIRECT11 x 10
14
See Fan Performance Table1
1100115/1/60
CentrifugalDirect - 1
1/20 - 3450115/1/60
.71Yes
High Velocity1 - 24x25 - 1in.
3 Round
Alum. Steel
20
6—456—56
Redundant - Single Stage
Hot Surface IgnitionMultiport Inshot
6115/1/60
14.1201/2
H x W x D41-3/4x26-1/2x30-1/2
205 / 193
TDH1B040A9H21AUpflow/Horizontal
40,00038,000
9530-60
DIRECT10 x 7
14
See Fan Performance Table1/2
1080115/1/60
CentrifugalDirect - 1
1/55 - 3000115/1/60
1.14Yes
High Velocity1 - 14x20 - 1in.
2 Round
Alum. Steel
20
2—452—56
Redundant - Single Stage
Hot Surface IgnitionMultiport Inshot
2115/1/60
9.7151/2
H x W x D41-3/4 x 19-1/2 x 30-1/2
145 / 135
TUH1C100A9H41AUpflow/Horizontal
97,00092,105
9535-65
DIRECT11 x 10
14
See Fan Performance Table3/4
1100115/1/60
CentrifugalDirect - 1
1/20 - 3450115/1/60
.71Yes
High Velocity1 - 20x25 - 1in.
3 Round
Alum. Steel
20
5—455—56
Redundant - Single Stage
Hot Surface IgnitionMultiport Inshot
5115/1/60
11.4151/2
H x W x D41-3/4 x 23 x 30-1/2
171/160
1 Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3.2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea
level. For Canadian applications, above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above
sea level.3 Based on U.S. government standard tests.4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.5 Constant torque ECM blower motor6 Refer to the Vent Length Table in the Installer's Guide or the Allowable Vent Length label located on the furnace.7 All TUH1 and TDH1 furnace models have a vent outlet diameter that equals 2".8 4 Speed, direct drive X13 style high efficiency DC motor
PRODUCT SPECIFICATIONS 1
MODELTYPERATINGS 2Input BTUH 3Capacity BTUH (ICS) 3AFUETemp. rise (Min.-Max.) °F.BLOWER DRIVE 8Diameter - Width (In.)No. UsedSpeeds (No.)CFM vs. in. w.g.Motor HP 5R.P.M.Volts/Ph/HzCOMBUSTION FAN — TypeDrive - No. SpeedsMotor HP - RPMVolts/Ph/HzFLAFILTER — Furnished?Type RecommendedShipped(No.-Size-Thk.)VENT PIPE DIAMETER - Min (in.)67
1 Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3.2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea
level. For Canadian applications, above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above
sea level.3 Based on U.S. government standard tests.4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.5 Constant torque ECM blower motor6 Refer to the Vent Length Table in the Installer's Guide or the Allowable Vent Length label located on the furnace.7 All TUH1 and TDH1 furnace models have a vent outlet diameter that equals 2".8 4 Speed, direct drive X13 style high efficiency DC motor