DONE BY: ARUN SINUSOIDAL STEADY STATE ANALYSIS 11/06/2022 1 SINUSOIDAL STEADY STATE ANALYSIS
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 1
DONE BY:
ARUN
SINUSOIDAL STEADY STATE ANALYSIS
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 2
OBJECTIVES OF THIS PRESENTATION• Learning how to represent a sine function with phase
• Learning about a phasor
• Converting rectangular form to polar form and vice versa
• Phase relationship for R,L,C and RLC circuits
• Impedance
• Phasor diagrams
• A sample problem
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 3
QUESTION???
• How will you represent mathematically a sine / cosine wave function with phase???
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 4
PHASOR• A sinusoidal current or voltage at a given frequency is characterized by only two
parameters
• 1. amplitude
• 2. phase angle
• The complex representation of voltage is also characterized by the same two parameters.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 5
• I=Imcos(wt+Φ)
• I=jImcos(wt+Φ)=Imej(wt+Φ)
Assumed sinusoidal form
Complex form of the corresponding current
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 6
• Throughout any linear circuit , operating in a sinusoidal steady state at a given frequency w, every current or voltage may be characterized completely by the knowledge of its amplitude and phase angle.
• None of the circuits we are considering will respond at a frequency other than that of the excitation source, so that the value of ‘w’ is always known.
• The complex representation of every voltage will contain the same factor e jwt. Hence, we can avoid carrying the redundant information throughout the solution.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 7
• Hence,
• I=ImejΦ
• The complex quantities are usually written in polar form than exponential form to achieve a slight addition of time saving and effort.
• Consider,
• v(t)=Vmcoswt
• It represented as VmL 0°
• i(t)=Imcos(wt+Φ)
• The real part of a complex quantity is i(t) = Re{Imej(wt+Φ)}
• I=ImL ΦThis abbreviated representation is called a phasor
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 8
Step 1 •i(t) = Imcos(wt+Φ)
Step 2•i(t) = Re{Imej(wt+Φ)}
Step 3•I=ImejΦ
Step 4•I=ImL Φ
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 9
• Important Points to keep in mind:
1. In Phasor representation, phasors are complex quantities and hence are printed in boldface type.
2. Capital letters are used for the phasor representation of an electrical quantity because the phasor is not an instantaneous function of time; it contains only amplitude and phase angle
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 10
PHASOR RELATIONSHIP FOR R,L AND C• Resistor
A
a.c. Source
R
V
Vmax
imax
VoltageCurrent
Voltage and current are in phase, and Ohm’s law applies for effective currents and voltages.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 11
• Inductor
A
L
V
a.c.
Vmax
imax
VoltageCurrent
The voltage peaks 900 before the current peaks. One builds as the other falls and vice versa.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 12
• Capacitor
Vmax
imax
VoltageCurrentA V
a.c.
C
The voltage peaks 900 after the current peaks. One builds as the other falls and vice versa.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 13
• Resistor
• V=I*R
• Inductor
• V=jwL*I
• Capacitor
• I=jwC*V
wL is called the inductive reactance (XL)
1/wC is called the capacitive reactance(XC)
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 14
IMPEDANCE• Consider a Series R,L,C circuit
L
VR VC
CRa.c.
VL
VT
ASeries ac circuit
Consider an inductor L, a capacitor C, and a resistor R all connected in series with an ac source. The instantaneous current and voltages can be measured with meters.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 15
VR
VC
VL
Phasor Diagram
q
VR
VL - VCVT
Source voltage
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 16
2 2( )T L CV i R X X
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 17
f
R
XL - XCZ
Impedance 2 2( )T L CV i R X X
or TT
VV iZ iZ
The impedance is the combined opposition to ac current consisting of both resistance and reactance.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 18
PHASOR DIAGRAMS• 1. The phasor diagram is a name given to a sketch in the complex plane showing
relationships of the phasor voltages and phasor currents throughout a specific circuit.
• 2. It also provides a graphical method for solving certain problems which may be used to check more exact analytical methods.
• 3.A phasor voltage 1cm long might represent 100V while a phasor current 1cm long might represent 3mA. Plotting both the phasors on the same diagram enables us to determine which waveform is leading or lagging.
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 19
• 4. The phasor diagram also offers an interesting interpretation of the time-domain to frequency-domain transformation.
• 5. In summary, the frequency-domain phasor appears on the phasor diagram and the transformation to the time domain is accomplished by allowing the phasor to rotate in a counter clockwise direction at a angular velocity of ‘w’ rad/s and then visualising the projection on the real axis
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 20
• Example:
• V=6+j8=10L 53.1°
j8
6
53.1°10
01/05/2023SINUSOIDAL STEADY STATE ANALYSIS 21
• THANK YOU