-
Owners Manual
I CRRFTSMRN°IPermanently LubricatedCompact
AIR COMPRESSORModel No. 919.152350
CAUTION: Read the Safety Guidelinesand All Instructions
Carefully Before
Operating.
• Safety Guidelines
• Assembly
• Operation
• Maintenance
• Service and Adjustments
• Troubleshooting
• Repair Parts
• Espahol
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.Visit
our Craftsman website: www.sears.com/craftsman
A08593 Rev. 0 11/4/04
-
SPECIFICATION CHART .................... 2
WARRANTY .............................. 2
SAFETY GUIDELINES .................... 3-6
GLOSSARY ............................... 7
ACCESSORIES ........................... 7
ASSEMBLY ............................... 7
Contents of Carton ...................... 7
To Remove Air compressor From Carton ..... 7
INSTALLATION ............................ 8
Location of Air Compressor ............... 8
Grounding Instructions ................... 8
Extension Cords ........................ 8
Voltage and Circuit Protection ............. 8
OPERATING PROCEDURES .............. 9-10
Know Your Air Compressor ............... 9
Description of Operation .................. 9
How to Use Your Unit ................... 10
How to Stop .......................... 10
To Use Quick Connect Sockets and Plugs . .10
To Use Female Tire Chuck ............... 10
To Use Blow Gun ...................... 10
Before Starting ........................ 10
How to Start .......................... 10
SERVICE AND ADJUSTMENTS ............. 11
Air Hose Replacement .................. 11
STORAGE ............................... 11
TROUBLESHOOTING GUIDE ............... 12
REPAIR PARTS ........................... 13
ESPAI_IOL ............................... 15
HOW TO ORDER REPAIR PARTS ..... back cover
SPECI FICATION CHARTModel No. 919-152350
Running Horsepower 1Displacement CFM 4.8Bore 1-7/8"
Stroke 1-1/4"
Voltage-Single Phase 120Minimum Branch Circuit Requirement 10
amps
Fuse Type Time DelaySCFM @40 psig 3.7SCFM @90 psig 2.6
FULL ONE YEAR WARRANTYAIR COMPRESSOR
If this air compressor fails due to a defect in material or
workmanship within one year from the date ofpurchase, RETURN IT TO
THE NEAREST SEARS REPAIR CENTER THROUGHOUT THE UNITED STATESAND
SEARS WILL REPAIR IT, FREE OF CHARGE. If purchased from Orchard
Supply Hardware, return tothe nearest Orchard Store and Orchard
will repair it, free of charge.
If this air compressor is used for commercial or rental
purposes, the warranty will apply for ninety daysfrom the date of
purchase.
This warranty gives you specific legal rights and you may have
other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, II
60179
A08593 2- ENG
-
SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize
this information, we use the symbolsbelow. Please read the manual
and pay attention to these sections.
Indicates an imminently hazardoussituation which, if not
avoided, will
result in death or serious injury.
Indicates a potentially hazardous sit-uation which, if not
avoided, could
result in death or serious injury.
Indicates a potentially hazardoussituation which, if not
avoided, may
result in minor or moderate injury.
Used without the safety alert sym-bol indicates a potentially
haz-
ardous situation which, if not avoided, may result inproperty
damaqe.
SAVE THESE INSTRUCTIONS
IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT
IN SERIOUS INJURYAND PROPERTY DAMAGE. READ AND UNDERSTAND ALL
WARNINGS AND OPERATING INSTRUC-TIONS BEFORE USING THIS
EQUIPMENT.
RISK OF EXPLOSION OR FIRE
WHAT CAN HAPPEN
IT IS NORMAL FOR ELECTRICAL CONTACTS WITHINTHE MOTOR AND
PRESSURE SWITCH TO SPARK.
IF ELECTRICAL SPARKS FROM COMPRESSOR COME
INTO CONTACT WITH FLAMMABLE VAPORS, THEYMAY IGNITE, CAUSING FIRE
OR EXPLOSION.
RESTRICTING ANY OF THE COMPRESSOR VENTILA-TION OPENINGS WILL
CAUSE SERIOUS OVERHEATINGAND COULD CAUSE FIRE.
UNATTENDED OPERATION OF THIS PRODUCT COULDRESULT IN PERSONAL
INJURY OR PROPERTY DAM-AGE.
HOW TO PREVENT IT
ALWAYS OPERATE THE COMPRESSOR IN A WELL VEN-
TILATED AREA FREE OF COMBUSTIBLE MATERIALS,GASOLINE OR SOLVENT
VAPORS.
IF SPRAYING FLAMMABLE MATERIALS, LOCATE COM-PRESSOR AT LEAST 20
FEET AWAY FROM SPRAYAREA. AN ADDITIONAL LENGTH OF HOSE MAY
BEREQUIRED.
STORE FLAMMABLE MATERIALS IN A SECURE LOCA-TION AWAY FROM
COMPRESSOR.
NEVER PLACE OBJECTS AGAINST OR ON TOP OFCOMPRESSOR. OPERATE
COMPRESSOR IN AN OPENAREA AT LEAST 12 INCHES AWAY FROM ANY WALLOR
OBSTRUCTION THAT WOULD RESTRICT THE FLOWOF FRESH AIR TO THE
VENTILATION OPENINGS.
OPERATE COMPRESSOR IN A CLEAN, DRY, WELL VENTI-LATED AREA. DO
NOT OPERATE UNIT INDOORS OR INANY CONFINED AREA.
ALWAYS REMAIN IN ATTENDANCE WITH THE PROD-UCT WHEN IT IS
OPERATING.
3- ENG A08593
-
RISK OF BURSTING
AIR TANK: THE FOLLOWING CONDITIONS COULD LEAD TO A WEAKENING OF
THE TANK, ANDRESULT IN A VIOLENT TANK EXPLOSION AND COULD CAUSE
PROPERTY DAMAGE OR SERIOUSINJ URY.
WHAT CAN HAPPEN HOW TO PREVENT IT
1. FAILURE TO PROPERLY DRAIN CONDENSEDWATER FROM THE TANK,
CAUSING RUST ANDTHINNING OF THE STEEL TANK.
2. MODIFICATIONS OR ATTEMPTED REPAIRS TO THETANK.
3. UNAUTHORIZED MODIFICATIONS TO THEUNLOADER VALVE, SAFETY
VALVE, OR ANYOTHER COMPONENTS WHICH CONTROL TANKPRESSURE.
4,
DRAIN TANK DALLY OR AFTER EACH USE. IF TANK
DEVELOPS A LEAK, REPLACE IT IMMEDIATELY WITH ANEW TANK OR
REPLACE THE ENTIRE COMPRESSOR.
NEVER DRILL INTO, WELD, OR MAKE ANY MODIFICA-TIONS TO THE TANK
OR ITS ATTACHMENTS.
THE TANK IS DESIGNED TO WITHSTAND SPECIFIC OPER-ATING PRESSURES,
NEVER MAKE ADJUSTMENTS ORPARTS SUBSTITUTIONS TO ALTER THE FACTORY
SETOPERATING PRESSURES.
EXCESSIVE VIBRATION CAN WEAKEN THE AIRTANK AND CAUSE RUPTURE OR
EXPLOSION.
ATTACHMENTS & ACCESSORIES:
EXCEEDING THE PRESSURE RATING OF AIR TOOLS,
FOR ESSENTIAL CONTROL OF AIR PRESSURE, YOUMUST INSTALL A
PRESSURE REGULATOR AND PRES-
SPRAY GUNS, AIR OPERATED ACCESSORIES, TIRES ANDOTHER INFLATABLES
CAN CAUSE THEM TO EXPLODEOR FLY APART, AND COULD RESULT IN SERIOUS
INJURY.
SURE GAUGE TO THE AIR OUTLET OF YOUR COM-PRESSOR. FOLLOW THE
EQUIPMENT MANUFACTURERSRECOMMENDATION AND NEVER EXCEED THE
MAXIMUMALLOWABLE PRESSURE RATING OF ATTACHMENTS.NEVER USE
COMPRESSOR TO INFLATE SMALL LOW-
PRESSURE OBJECTS SUCH AS CHILDREN'S TOYS,FOOTBALLS, BASKETBALLS,
ETC.
RISK FROM FLYING OBJECTS
WHAT CAN HAPPEN
THE COMPRESSED AIR STREAM CAN CAUSE SOFT TIS-SUE DAMAGE TO
EXPOSED SKIN AND CAN PROPEL
DIRT, CHIPS, LOOSE PARTICLES AND SMALL OBJECTSAT HIGH SPEED,
RESULTING IN PROPERTY DAMAGE ORPERSONAL INJURY.
HOW TO PREVENT IT
ALWAYS WEAR ANSI Z87.1 APPROVED SAFETY GLASS-ES WITH SIDE
SHIELDS WHEN USING THE COMPRES-SOR.
NEVER POINT ANY NOZZLE OR SPRAYER TOWARDANY PART OF THE BODY OR
AT OTHER PEOPLE ORANIMALS.
ALWAYS TURN THE COMPRESSOR OFF AND BLEEDPRESSURE FROM THE AIR
HOSE AND TANK BEFOREATTEMPTING MAINTENANCE, ATTACHING TOOLS
ORACCESSORIES.
A08593 4-ENG
-
RISK OF ELECTRICAL SHOCK
WHAT CAN HAPPEN
YOUR AIR COMPRESSOR IS POWERED BY ELECTRICI-TY. LIKE ANY OTHER
ELECTRICALLY POWERED DEVICE,IF IT IS NOT USED PROPERLY IT MAY CAUSE
ELECTRICSHOCK.
REPAIRS ATTEMPTED BY UNQUALIFIED PERSONNELCAN RESULT IN SERIOUS
INJURY OR DEATH BY ELEC-TROCUTION.
ELECTRICAL GROUNDING: FAILURE TO PROVIDE ADE-QUATE GROUNDING TO
THIS PRODUCT COULDRESULT IN SERIOUS INJURY OR DEATH FROM
ELEC-TROCUTION. SEE GROUNDING INSTRUCTIONS,
HOW TO PREVENT IT
NEVER OPERATE THE COMPRESSOR OUTDOORS WHENIT IS RAINING OR IN
WET CONDITIONS.
NEVER OPERATE COMPRESSOR WITH PROTECTIV-COVERS REMOVED OR
DAMAGED,
ANY ELECTRICAL WIRING OR REPAIRS REQUIRED ONTHIS PRODUCT SHOULD
BE PERFORMED BY AUTHO-RIZED SERVICE CENTER PERSONNEL IN
ACCORDANCEWITH NATIONAL AND LOCAL ELECTRICAL CODES.
MAKE CERTAIN THAT THE ELECTRICAL CIRCUIT TOWHICH THE COMPRESSOR
IS CONNECTED PROVIDES
PROPER ELECTRICAL GROUNDING, CORRECT VOLT-AGE AND ADEQUATE FUSE
PROTECTION.
RISK TO BREATHING
WHAT CAN HAPPEN HOW TO PREVENT IT
THE COMPRESSED AIR DIRECTLY FROM YOUR COM-PRESSOR IS NOT SAFE
FOR BREATHING. THE AIR
STREAM MAY CONTAIN CARBON MONOXIDE, TOXICVAPORS, OR SOLID
PARTICLES FROM THE TANK.BREATHING THESE CONTAMINANTS CAN
CAUSESERIOUS INJURY OR DEATH.
SPRAYED MATERIALS SUCH AS PAINT, PAINT SOL-VENTS, PAINT REMOVER,
INSECTICIDES, WEEDKILLERS, CONTAIN HARMFUL VAPORS AND POISONS.
AIR OBTAINED DIRECTLY FROM THE COMPRESSORSHOULD NEVER BE USED TO
SUPPLY AIR FOR HUMANCONSUMPTION. IN ORDER TO USE AIR PRODUCED
BYTHIS COMPRESSOR FOR BREATHING, SUITABLE FIL-TERS AND IN-LINE
SAFETY EQUIPMENT MUST BEPROPERLY INSTALLED, IN-LINE FILTERS AND
SAFETYEQUIPMENT USED IN CONJUNCTION WITH THE COM-PRESSOR MUST BE
CAPABLE OF TREATING AIR TO ALLAPPLICABLE LOCAL AND FEDERAL CODES
PRIOR TOHUMAN CONSUMPTION.
WORK IN AN AREA WITH GOOD CROSS-VENTILATION.READ AND FOLLOW THE
SAFETY INSTRUCTIONS PRO-VIDED ON THE LABEL OR SAFETY DATA SHEETS
FORTHE MATERIAL YOU ARE SPRAYING. USE ANIOSH/MSHA APPROVED
RESPIRATOR DESIGNED FORUSE WITH YOUR SPECIFIC APPLICATION,
5- ENG A08593
-
RISK OF BURNS
WHAT CAN HAPPEN
TOUCHING EXPOSED METAL SUCH AS THE COMPRES-
SOR HEAD OR OUTLET TUBES, CAN RESULT INSERIOUS BURNS.
HOW TO PREVENT IT
NEVER TOUCH ANY EXPOSED METAL PARTS ONCOMPRESSOR DURING OR
IMMEDIATELY AFTER OPER-ATION. COMPRESSOR WILL REMAIN HOT FOR
SEVERALMINUTES AFTER OPERATION.
DO NOT REACH AROUND PROTECTIVE SHROUDS ORATTEMPT MAINTENANCE
UNTIL UNIT HAS BEENALLOWED TO COOL.
RISK FROM MOVING PARTS
WHAT CAN HAPPEN HOW TO PREVENT IT
MOVING PARTS SUCH AS THE PULLEY, FLYWHEEL ANDBELT CAN CAUSE
SERIOUS INJURY IF THEY COMEINTO CONTACT WITH YOU OR YOUR
CLOTHING,
ATTEMPTING TO OPERATE COMPRESSOR WITH DAM-AGED OR MISSING PARTS
OR ATTEMPTING TO REPAIRCOMPRESSOR WITH PROTECTIVE SHROUDS
REMOVEDCAN EXPOSE YOU TO MOVING PARTS AND CANRESULT IN SERIOUS
INJURY.
NEVER OPERATE THE COMPRESSOR WITH GUARDSOR COVERS WHICH ARE
DAMAGED OR REMOVED.
ANY REPAIRS REQUIRED ON THIS PRODUCT SHOULDBE PERFORMED BY
AUTHORIZED SERVICE CENTERPERSONNEL.
RISK OF FALLING
WHAT CAN HAPPEN HOW TO PREVENT IT
A PORTABLE COMPRESSOR CAN FALL FROM A TABLE,WORKBENCH OR ROOF
CAUSING DAMAGE TO THECOMPRESSOR AND COULD RESULT IN SERIOUSINJURY
OR DEATH TO THE OPERATOR.
ALWAYS OPERATE COMPRESSOR IN A STABLESECURE POSITION TO PREVENT
ACCIDENTAL MOVE-MENT OF THE UNIT. NEVER OPERATE COMPRESSORON A ROOF
OR OTHER ELEVATED POSITION. USEADDITIONAL AIR HOSE TO REACH HIGH
LOCATIONS.
RISK OF PROPERTY DAMAGE WHEN TRANSPORTINGCOMPRESSOR
(Fire, Inhalation, Damage to Vehicle Surfaces)
For units requiring oil in pump or gasoline engines
WHAT CAN HAPPEN HOW TO PREVENT IT
OIL CAN LEAK OR SPILL AND COULD RESULT IN FIRE
OR BREATHING HAZARD, SERIOUS INJURY OR DEATHCAN RESULT. OIL
LEAKS WILL DAMAGE CARPET, PAINTOR OTHER SURFACES IN VEHICLES OR
TRAILERS,
A08593
ALWAYS PLACE COMPRESSOR ON A PROTECTIVE MATWHEN TRANSPORTING TO
PROTECT AGAINST DAMAGETO VEHICLE FROM LEAKS, REMOVE COMPRESSORFROM
VEHICLE IMMEDIATELY UPON ARRIVAL AT YOURDESTINATION.
6 - ENG
-
Become familiar with these terms before operating theunit.
CFM: Cubic feet per minute.
SOFM: Standard cubic feet per minute; a unit ofmeasure of air
delivery.
PSlG: Pounds per square inch gauge; a unit of meas-ure of
pressure.
Code Certification: Products that bear one or moreof the
following marks: UL, CUL, ETL, CETL, havebeen evaluated by ©SHA
certified independent safetylaboratories and meet the applicable
UnderwritersLaboratories Standards for Safety.
Branch Circuit: Circuit carrying electricity from elec-trical
panel to outlet
This unit is capable of powering the following Accessories. The
accessories are available through the currentPower and Hand Tool
Catalog or full-line Sears stores.
Accessories
Quick Connect Sets (various sizes)
Specialty Tools
Air Brush
Inflating/Blow Gun
Grease Gun
Caulk Gun
Carpentry Tools
Finishing Nailer / Stapler
Contents of Carton
1. Air Compressor with hose and pressureadjustment valve (qty
1)
2. Quick Connect Coupling (qty 1)
3. Quick Connect Studs (qty 2)
4. Thread Sealant Tape (qty 1)
5. Female Tire Chuck (qty 1)
6. Blow Gun (qty 1)
7. Safety Nozzle (qty 1)
8. Blow Gun Adapter (qty 1)
9. Inflating Needle (qty 1)
10. Tapered Inflator (qty 1)
To Remove Air Compressor From Carton
1. Grasp handle and lift the air compressor out ofthe
carton.
2. Remove all packaging from air compressor anddiscard.
9 8
7- ENG A08593
-
HOW TO SET UP YOUR UNIT
Location of the Air Compressor
Locate the air compressor in a clean, dry and wellventilated
area. The air compressor pump and shroudare designed to allow for
proper cooling. The ventila-tion openings on the compressor are
necessary tomaintain proper operating temperature. Do not placerags
or other containers on or near these openings.
GROUNDING INSTRUCTIONS
RISK OF ELECTRICALSHOCK. In the event of a
short circuit, grounding reduces the risk ofshock by providing
an escape wire for theelectric current. This air compressor must
beproperly grounded.
The portable air compressor is equipped with a cordhaving a
grounding wire with an appropriate ground-ing plug (see following
illustrations). The plug must beused with an outlet that has been
installed andgrounded in accordance with all local codes and
ordi-nances.
1. The cord set and plug with this unit contains agrounding pin.
This plug MUST be used with agrounded outlet.
IMPORTANT: The outlet being used must be installedand grounded
in accordance with all local codes andordinances.
2. Make sure the outlet being used has the sameconfiguration as
the grounded plug. DO NOT USEAN ADAPTER. See figure.
3.
4.
Grounding Pin
@--_ Grounded
/ Outlets
Inspect the plug and cord before each use. Donot use if there
are signs of damage.
If these grounding instructions are not completelyunderstood, or
if in doubt as to whether the com-pressor is properly grounded,
have the installationchecked by a qualified electrician.
TRICAL SHOCK.
IMPROPER GROUNDINGRESULT IN ELEC-
Do not modify the plug provided. If it doesnot fit the available
outlet, a correct outletshould be installed by a qualified
electri-cian.
Repairs to the cord set or plug MUST bemade by a qualified
electrician.
Extension Cords
Use extra air hose instead of an extension cord to
avoid voltage drop and power loss to the motor, andto prevent
overheating.
If an extension cord must be used, be sure it is:
• a 3-wire extension cord that has a 3-blade
grounding plug, and a 3-slot receptacle that willaccept the plug
on the product
• in good condition
• no longer than 50 feet
• 14 gauge (AWG) or larger. (Wire size increases asgauge number
decreases. 12 AWG, 10 AWG, and8 AWG may also be used. DO NOT USE 16
OR18 AWG.)
Voltage and Circuit Protection
Refer to the Parts Manual for the voltage and mini-mum branch
circuit requirements.
Certain air compressors can be operated on a 15 ampcircuit if
the following conditions are met.
1. Voltage supply through branch circuit is 15 amps.
2. Circuit is not used to supply any other electricalneeds
(lights, appliances, etc.).
3. Extension cords comply with specifications.
4. Circuit is equipped with a 15 amp circuit breakeror 15 amp
time delay fuse. NOTE: If compressoris connected to a circuit
protected by fuses, useonly time delay fuses marked "D".
If any of the above conditions cannot be met, or ifoperation of
the compressor repeatedly causes inter-ruption of the power, it may
be necessary to operate itfrom a 20 amp circuit. It is not
necessary to changethe cord set.
A08593 8-ENG
-
Know Your Air Compressor
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustra-tions with your unit to familiarize
yourself with the location of various controls and adjustments.
Save this manualfor future reference.
On/Off Switch
Pressure
Adjustment
Quick Connect
Coupling Tapered Inflator
Inflating Needle
Connect
Description of Operation
Pressure Adjustable Valve: The pressure valve con-trols the
amount of pressure going from the air com-pressor to the accessory.
The pressure adjusting valvecan be used to set approximate pressure
between 10and 125 PSI (125 PSI is the highest pressure
thiscompressor will deliver).
On/Off Switch (located on opposite side of aircompressor): Used
to turn air compressor on and off.
Quick Connect Coupling: Makes tool change overseasy.
Quick Connect Studs: Install on tools and insert intothe quick
connect coupling to make tool changeovers easier.
Thread Sealant Tape: Use on threads to eliminate airleaks.
Female Tire Chuck: Adapter for inflating tires.
Blow Gun: Ideal for blowing, cleaning, and inflating.
Safety Nozzle: Prevents pressure build-up.
Blow Gun Adapter: Attached to blow gun or femalehose end to
allow the tapered Inflator or inflating nee-dle to be used.
Inflating needle: Used to inflate sport balls.
Tapered Inflator: Used to inflate toy
inflatables/airmattresses.
9- ENG A08593
-
How to Use Your Unit
How to Stop:
1. Set the On/Off switch to"OFF".
To Use Quick Connect
Coupling and Studs
1. Apply thread sealant tapeto threads of quick con-nect
coupling and studs,
2. Assemble the quick con-nect coupling to the hose,Attach the
studs to theblow gun and female tire chuck. Tighten securely,This
will make it easier to change over theseaccessories.
3. Pull quick connect coupling back and insert stud.See figure
above,
4. Slide coupling forward to lock in place,
To Use Female Tire Chuck
1. Attach female tire chuck to hose.
2. See the "How to Start" paragraph to start aircompressor.
3. Place the female tire chuck onto the tire valvestem of the
tire to be inflated.
, Slowly increase the pressure setting of theadjustable pressure
valve to the tire manufactur-er's recommended PSI. Note: To ensure
correct
tire pressure use a tire pressure gauge.
To Use Blow Gun
1, Attach the blow gun to hose.
If an accessoryis not being
used with the blow gun, thesafety nozzle MUST beassembled.
Safety Nozzle
2. Assemble the safety nozzle or blow gun adapterto blow gun.
See next figure.
NOTE: To use the inflating needle or tapered inflatorthe blow
gun adapter has to be assembled to blowgun.
I Lever BlowGunAdapter
Inflating Needle
Tapered Inflator
Safety Nozzle
3. Attach the inflating needle or tapered inflator tothe blow
gun adapter on the blow gun.
4. See the "How to Start" paragraph to start aircompressor.
5. Depress lever on blow gun to release the air.
Before Starting:
1. Place On/Off switch to "OFF".
2. Place theadjustable pres-sure valve to 10PSI.
2. Attach hose andaccessories.
Too much air pressurecauses a hazardous risk of
bursting. Check the manufacturer's maximumpressure rating for
air tools and accessories.Carefully follow the "How to Start"
instruc-tions.
How to Start:
1. Place On/Off switch to "OFF".
2.
3.
4.
5,
Plug the power cord into the grounded outlet.
Place On/Off switch to "ON" to start compressor.
Check the manufacturer's maximum pressure rat-ing for the air
tool, accessory, or vehicle tire beingused. The air compressor
outlet pressure mustnever exceed the maximum pressure rating.
Slowly increase the pressure setting of theadjustable pressure
valve. You should be able tohear and feel air pressure being
relieved by theadjustable pressure valve. If pressure is not
beingrelieved, turn the air compressor off immediately.The pressure
valve must be replaced.
Compressed air from theoutfit may contain water
condensation. Do not spray unfiltered air atan item that could
be damaged. Some airoperated tools or devices may require
filteredair. Read the instructions for the air tool ordevice.
A08593 10-ENG
-
Air Hose Replacement
The air hose attached to your compressor has anintegral pressure
adjusting valve at the working end ofthe hose. Should service or
replacement be required,make sure that the pressure adjusting valve
is presentin the air hose line.
DO NOT replace the hosewith standard hose that is
not equipped with the pressure adjustingvalve. The appropriate
hose assembly foryour compressor is available at Sears.
Do not allow hose tobecome kinked or
pinched at any time. This is important toavoid damage to your
compressor and tomaintain pressure adjusting valve control.
1.
2.
Set the On/Off switch to "OFF" and unplug thecord.
Relieve all pressure from the air compressor headand air hose by
turning the adjustable pressurevalve to 10 PSI.
3. Protect the electrical cord and air hose from dam-
age by winding them loosely around the air com-pressor.
4. Store the air compressor in a clean and dry loca-tion.
11- ENG A08593
-
Voltage sources, moving parts, or compressed air sources are
exposed when repairing thecompressor. Personal injury can occur.
Unplug the compressor before attempting any repairs.
PROBLEM
Air Leaks
Compressor is not deliveringenough air.
Motor will not run.
CAUSE
Hose fitting loose.
Prolonged excessive use of air.
Hole in hose.
Air leaks.
CORRECTION
Tighten fitting.
Decrease the amount of air usage.Your compressor is not
largeenough for the air requirement.
Fuse blown, circuit breakertripped.
Extension cord is wrong length orgauge.
High discharge pressure. Cannotbe adjusted lower.
Loose electrical connections.
Faulty motor.
Adjustable pressure valve notfunctioning.
Replace the hose.
Tighten fittings.
1.
2.
3.
4.
5.
Check fuse box for blown fuse
and replace as necessary.Reset circuit breaker. Do notuse a fuse
or circuit breaker
with higher rating than thatspecified for your particularbranch
circuit.
Check for proper fuse. Youshould be using a "TimeDelay"
fuse.
Check for low voltage prob-lem.
Check the extension cord.
Disconnect the other electricalappliances from circuit oroperate
the compressor on itsown branch circuit.
Check the extension cord.
Check wiring connection insideterminal box area.
Contact a Trained ServiceTechnician.
Risk of burst-ing. DO NOT
operate the compressor if thisproblem exists. Adjustable
pres-sure valve must be replaced.
A08593 12 - ENG
-
14
19 Torque30-45 in.-Ibs.
15
/16
21
/ 2322
KEY
NO1234567899-89-99-109-119-129-1312131415161718192O212223
\18
+
X
+
×
×
3
717
PART NO. DESCRIPTIONSSF-995 Screw #10-24 x 718 (4)CAC-1196
Cylinder HeadCAC-1212 Tube SealCAC-1199 Head GasketZ-A08548 Valve
Plate AssemblySSG-8169 "O" RingAC-0187-1 Outlet Tube
GasketZ-A04615 Sub Pump Assembly
Rod AssemblyPre-Formed Compression RingConnecting Rod Cap
D21127 Screw #10-24SSF-3147 Screw 3/8-16 UNC
Cylinder SleeveAC-0815 Timing BeltD25731 Pump Isolator
(5)CAC-1319-1 Shroud (left)D21709 Label, Tool RatingCAC-1320 Shroud
(right)CAC-1206-1 ClampCAC-4324 Pressure Valve Assembly and
HoseSUDL-9-1 Screw, GroundSSS-16 SwitchSSF-3156 Shroud Screws
(5)CAC-1211 Housing Isolator (3)D21708 Label, Performance
NOT ILLUSTRATED/NO SE MUSTRANx KK-4929 Fastener Kit> KK-4964
Connecting Rod Kit
D30139 Gasket & Seal Kit+ D30324 Ring Kit
A08593 Owner's ManualLA-3146 Label, WarningD23786 Power
CordD23787 Jumper Wire
22
DESCRIPCIONTornillo #10-24 x 7/8 (4)Cabezal del cilindroSello
del tuboJunta - CabezalPlaca de la valvulaAnillo "O"Tubo de
salidaJuntaConjunto de Sub-BombaEnsamblaje de la bielaRing Anillo
de compresidn preformadoTapa de la barra de conexi6nTornillo
#10-24Tornillo 3/8-16 UNCManga del CilindroCorrea de
regulaci6nAislante de pompe (5)Cubierta, izquierdaR6tulo, grade de
la herramientaLubierta, derechaAbrazaderaValvula de presidn y
mangueraTornillos para TierraInterruptorTornillos para la cubierta
(5)Aislante del casco (3)R6tulo, funcionamiento
El juego de sujetadoresEl juego de la barra de conexi6nJuego de
empaquetaduras y sellosConjunto de sujeci6n juego de anilloManual
del propietarioR6tulo, advertenciaCable electricoAlambre de
puente
13-ENG A08593
-
HOJA DE ESPECIFICACIONES ............... 14
GARANTIA ................................ 14
NORMAS DE SEGURIDAD ................ 15-18
GLOSARIO ................................ 19
ACCESORIOS ............................. 19
ENSAMBLADO ............................. 19
Contenido de la caja ..................... 19
C6mo extraer el compresor de aire de la caja..19
INSTALACION ............................. 20
Ubicaci6n del compresor de aire ............ 20
Instrucciones para conectar a tierra ......... 20
Extensiones el@ctricas .................... 20
Protecci6n del voltaje y del circuito .......... 20
PROCEDIMIENTOS OPERATIVOS .......... 21-22
Conozca su compresor de aire ............. 21
Descripci6n de operaciones ................ 21
Come usar su unidad ..................... 22
Come detenerla ......................... 22
C6mo utilizar z6calos y enchufes de
conexi6n r_.pida ......................... 22
C6mo utilizar el pico hembra para el infladode los neum6.ticos
....................... 22C6mo utilizar la pistola sopladora
........... 22
Antes de comenzar ...................... 22
C6mo dar arranque ...................... 22
SERVIClOS Y REGULAClONES ............... 23
Reemplazo de la manguera de aire .......... 23
ALMACENAJE ............................. 23
GUlA DE DIAGNOSTICO DE PROBLEMAS ...... 24
PIEZAS DE REPARACION ................... 13
COMO SOUCITAR PIEZAS PAPA REPARACION
............................... contratapa
HOJA DE ESPECIFICACIONESModelo 919-152350
Potwncia de trabajo 0,1CFM de desplazamiento 4,8Di_.metro
1-7/8"
Carrera 1-1/4"
Voltaje - Monof_.sico 120
Requerimientos minimo por circuito ramal 10 ATipo de fusible
Acci6n retardadaSCFM a 40 PSIG 3,7
SCFM a 90 PSIG 2,6
GARANTIA COMPLETA POR UN AI_IOCOMPRESOR DE AIRE
Si este compresor de aire fallara por defectos en materiales o
mano de obra dentro del lapso de un aSoa partir de lafecha de su
compra, DEVUC:LVALOAL CENTRO DE REPARACIONESSEARS MAS CERCANO
DENTRODE LOSESTADOSUNIDOS, Y SEARS LO REPARARA,LIBRE DE CARGO. Si
se hubiese comprado a Orchard SupplyHardware, devu@lvaloal comercio
Orchard mas cercano y Orchard Io reparar_.,libre de cargo.
Si este compresor de aire fuese utilizado para propositos
comerciales o de alquiler, la garantia solo tendra validezpor
noventa dias a partir de la compra.
Esta garantia le otorga derechos legales especificos, aunque
usted podr_,tener otros derechos que podrian variarentre
estados.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, II
60179
A08593 14- SP
-
SEGURIDAD Y PREVENCION DE PROBLEMAS DEL EQUIPO: Para ayudar al
reconocimiento de esta informaciOn, hemosutilizado los simbolos
mostrados abajo. Sfrvase leer el manual y prestar atenciOn a dichas
secciones.
Indica una situaci6n de inminente riesgo, la cual,si no es
evitada, causarA la muerte o lesiones
serias.
Indica una situaciOn potencialmenteriesgosa, que si no es
evitada, podria
resultar en la muerte o lesiones serias.
_lndica una situaciOn potencialmentepeligrosa, la cual, si no es
evitada, podria
resultar en lesiones menores o moderadas.
Usado sin el simbolo de seguridad dealerta indica una situaci6n
potencial-
mente riesgosa la que, si no es evitada, podria causar dafios
enla propiedad.
GUARDE ESTAS INSTRUCClONES
La operacibn o el mantenimiento inadecuados de este producto
podrian ocasionar serias lesiones ydafios a la propiedad. Lea y
comprenda todas las advertencias e instrucciones de
funcionamientoantes de utilizar este equipo.
RIESGO DE EXPLOSION O INCENDIO
&QUI_ PUEDE OCURRIR?
PARA LOS CONTACTOS ELI_CTRICOS ES NORMAL LAEXISTENCIA DE CHISPAS
ENTRE EL MOTOR Y ELINTERRUPTOR A PRESION.
SI LAS CHISPAS EL¢CTRICAS PROVENIENTES DEL COMPRESORTOMARAN
CONTACTO CON EMANACIONES DE MATERIALESINFLAMABLES, ELLOS PODRIAN
ARDER ORIGINANDOINCENDIO O EXPLOSION.
RESTRINGIR CUALQUIERA DE LAS ABERTURAS DEVENTILAClON CAUSARA UN
SERIO RECALENTAMIENTOY PODRIA PRODUCIR UN INCENDIO.
DEJAR DESATENDIDO ESTE PRODUCTO MIENTRAS ELMISMO EST,&. EN
FUNCIONAMIENTO PUEDE RESULTAR ENLESlONES PERSONALES O DAI_IOS A LA
PROPIEDAD.
_,C6MO PREVENIRLO?
OPERE SIEMPRE EL COMPRESOR EN UN SECTOR BIENVENTILADO Y LIBRE DE
MATERIALES COMBUSTIBLES,GASOLINA O EMANAClONES DE SOLVENTE.
EN UN AREA DE ROCIADO DE MATERIALES INFLAMABLES,
UBIQUE AL COMPRESOR POR LO MENOS A 6,1M (20 PIES) DEDISTANCIA
DEL h.REA DE ROCIADO. PODRiA REQUERIRSEUNA EXTENSION DE LA
MANGUERA.
ALMACENE LOS MATERIALES INFLAMABLES EN UNAUBICACION SEGURA,
ALEJADOS DEL COMPRESOR.
JAMAS COLOQUE OBJETOS APOYADOS O SOBRE EL COM-PRESOR. OPERE EL
COMPRESOR EN UN SECTOR ABIERTO,
POR LO MENOS A 30 CM (12 PULGADAS) ALEJADO DECUALQUIER PARED U
OBSTRUCCION QUE RESTRINJA ELFLUJO DE AIRE FRESCO A LAS ABERTURAS DE
VENTILACION.
OPERE EL COMPRESOR EN UN SECTOR LIMPIO, SECO, Y BIENVENTILADO.
NO OPERE LA UNIDAD EN ESPACIOS CERRADOSO CUALQUlER ,&,REA
CONFINADA.
MANTleNGASE SlEMPRE ALERTA CADA VEZ QUE ELPRODUCTO ESTE
FUNCIONANDO.
15- SP A08593
-
RIESGO DE EXPLOSION
TANQUE DE AIRE: LAS SIGUIENTES CONDICIONES PUEDEN DETERMINAR EL
DEBILITAMIENTODEL TANQUE, Y ORIGINAR UNA VIOLENTA EXPLOSION DEL
MISMO, SIENDO CAUSA DE DAhlOS ALA PROPIEDAD 0 LESIONES SERIAS.
2.
3.
_,QU¢: PUEDE OCURRIR? &C6MO PREVENIRLO?
DRENAJE INADECUADO DEL AGUA CONDENSADA ENEL TANQUE, SIENDO LA
CAUSA DEL OXIDO QUE REDUCEEL ESPESOR DEL TANQUE DE ACERO.
MODIFICACIONES O INTENTO DE REPARACIONES ALTANQUE.
MODIFICACIONES NO AUTORIZADAS A LA VALVULA DEDESCARGA, VALVULA
DE SEGURIDAD 0 CUALQUIEROTRO COMPONENTE QUE CONTROLE LA PRESION
DELTANQUE.
LA VIBRACION EXCESIVA PUEDE DEBILITAR EL TANQUEDE AIRE Y CAUSAR
SU RUPTURA O EXPLOSION.
AGREGADOS Y ACCESORIOS
EL EXCESO A LOS VALORES DE PRESION ESTABLECIDOSPARA I.AS
HERRAMIENTAS NEUMATICAS, PISTOLAS ROGIADO-RAS, ACCESORIOS ACTIVADOS
POR AIRE, CUBIERTAS Y OTROSOBJETOS INFLABLES, PUEDE CAUSAR SU
EXPLOSION O SERARROJADOS, PUDIENDO OCASIONAR SERIAS LESIONES.
DRENE EL TANQUE DIARIAMENTE O DESPUI_S DE CADA USO.Sl EL TANQUE
GENERA UNA PCRDIDA, REEMPLikCELOINMEDIATAMENTE CON UN NUEVO TANQUE
O REEMPLACE ELCOMPRESOR COMPLETO.
JAMAS PERFORE, SUELDE, O EFECTUE MODIFICACION ALGUNAAL TANOUE O
SUS ACCESORIOS.
EL TANQUE ESTik DISENADO PARA RESISTIR PRESIONESOPERATIVAS
ESPECiFICAS. JAMAS EFECTUE AJUSTES OSUSTITUYA PARTES QUE ALTEREN
LAS REGULACIONES DEPRESION ORIGINALES DE FABRICA.
PARA UN CONTROL ESENCIAL DE LA PRESION, DEBE USTEDINSTALAR UN
REGULADOR Y UN MEDIDOR DE PRESlON A LA
SALIDA DEL AIRE DE SU COMPRESOR. (Sl NO ESTUNIEREQUIPADO) SIGA
LAS RECOMENDACIONES DE LOSFABRICANTES DE SU EQUIPO Y JAMAS EXCEDA
LOS VALORESM/kXIMOS DE PRESION PERMITIDOS PARA LOS ACCESORIOS.JAMAS
USE EL COMPRESOR PARA INFLAR OBJETOS QUEREOUIEREN POOA O BAJA
PRESlON, TALES COMOJUGUETES PARA LOS NII_IOS, PELOTAS DE FUTBOL,
PELOTASDE BASQUET, ETC.
RIESGO DE OBJETOS ARROJADOS POR EL AIRE.
_,QU¢: PUEDE OCURRIR?
EL CHORRO DE AIRE COMPRIMIDO PUEDE CAUSAR DAI_IOS
SOBRE LOS TEJIDOS BLANDOS DE LA PIEL EXPUESTA, YPUEDE PROPULSAR
SUCIEDAD, ASTILLAS, PARTICULASSUELTAS Y PEQUE_IOSOBJETOS A ALTA
VELOClDAD, OCASIONANDODANOS A LA PROPIEDAD O LESIONES
PERSONALES.
&C6MO PREVENIRLO?
AL UTILIZAR EL COMPRESOR, USE SIEMPRE ANTEOJOS DESEGURIDAD ANSI
Z87.1 APROBADOS, CON PROTEOCIONLATERAL.
JAMAS APUNTE NINGUNA BOQUlLLA O PULVERIZADOR
HAOIA PARTES DEL CUERPO, A OTRAS PERSONAS OANIMALES.
APAGUE SIEMPRE EL COMPRESOR Y PURGUE LA PRESION
DE LA MANGUERA DEL AIRE Y DEL TANQUE, ANTES DE INTENTAREL
MANTENIMIENTO, EL ACOPLE DE HERRAMIENTAS OACCESORIOS.
A08593 16- SP
-
RIESGO DE DESCARGA ELI=CTRICA
_QUEPUEDE OCURRIR?
SU COMPRESOR DE AIRE ESTA ACCIONADO POR ELECTRICIDAD.COMO
CUALQUIER OTRO DISPOSITIVO ELECTRICO IMPULSADOEL¢CTRICAMENTE, Sl NO
SE LO UTILIZA ADECUADAMENTE,PODRiA CAUSARLE UNA DESCARGA
ELleCTRICA.
LAS REPARAClONES INTENTADAS POR PERSONAL NOCALIFICADO PODRIAN
OCASlONAR SERIAS LESlONES O LAMUERTE POR ELECTROCUCION.
CONEXION A TIERRA: DEJAR DE PROVEER UNA ADECUADACONEXlON A
TIERRA A ESTE PRODUCTO PODRiA OCASlONARLESlONES SERIAS O LA MUERTE
POR ELECTROCUCION. VERINSTRUCCIONES PARA LA PUESTA A TIERRA.
_C6MO PREVENIRLO?
JAMAS OPERE EL COMPRESOR A LA INTEMPERIE CUANDOESTA LLOVlENDO O
EN CONDICIONES DE HUMEDAD.
NUNCA OPERE EL COMPRESOR SIN SUS DEFENSAS O SUSCUBIERTAS
REMOVIDAS O DAI_IADAS.
CUALQUIER CONEXlON ELleCTRICA O REPARACION
REQUERIDA POR ESTE PRODUCTO DEBE SER EFECTUADAPOR PERSONAL
AUTORIZADO DE LOS SERVICENTROS DEACUERDO A LOS CODIGOS ELECTRICOS
NACIONALES YLOCALES.
ASEGURESE QUE EL CIRCUITO ELleCTRICO AL CUAL ESTACONECTADO EL
COMPRESOR, SUMINISTRA APROPIADACONEXlON A TIERRA, TENSION CORRECTA
Y UNA ADECUADAPROTECCION DE FUSlBLES.
RIESGO DE INHALACION
&QU¢: PUEDE OCURRIR? _,COMO PREVENIRLO?
EL AIRE COMPRIMIDO PROVENIENTE DEL COMPRESOR NOES SANO PARA
RESPIRAR. EL CHORRO DE AIRE PUEDE
CONTENER MONOXlDO DE CARBONO, VAPORES T(_XlCOS OPART[CULAS
SOLIDAS PROVENIENTES DEL TANQUE. LAINHALACION DE DICHOS
CONTAMINANTES PUEDE LLEGAR ACAUSAR SERIAS LESlONES O LA MUERTE.
EL ROCIADO DE MATERIALES TALES COMO PINTURA,SOLVENTES,
REMOVEDORES DE PINTURA, INSECTICIDAS, MATAHIERBAS, CONTIENEN
EMANACIONES DAi_INAS Y VENENOSAS.
EL AIRE OBTENIDO DIRECTAMENTE DEL COMPRESOR JAMASDEBERA SER
UTILIZADO PARA PROVEER AIRE PARA CONSUMOHUMANO. PARA PODER UTILIZAR
EL AIRE PRODUCIDO PORESTE COMPRESOR Y HACERLO RESPIRABLE,
DEBERANINSTALARSE UN FILTRO ADECUADO Y UN EQUlPO DESEGURIDAD
INTERCALADO. LOS FILTROS INTERCALADOSTANTO COMO EL EQUIPO DE
SEGURIDAD UTILIZADO ENCON JUNTO CON EL COMPRESOR, DEBERAN SER
CAPACESDE PROCESAR EL TRATAMIENTO DEL AIRE DE ACUERDO ATODOS LOS
CODIGOS LOCALES Y FEDERALES, PREVIO ALCONSUMO HUMANO.
TRABAJE EN UN .&.REA CON BUENA VENTILACION CRUZADA.LEA Y
SIGA LAS INSTRUCCIONES DE SEGURIDAD PROVISTASEN EL ROTULO O EN LOS
DATOS DE LAS HOJAS DE SEGURIDADDEL MATERIAL QUE
EST.&.PULVERIZANDO. USE EL RESPIRADORAPROBADO NIOSH/MSHA
DESIGNADO PARA UTILIZARSE CONSU APLICACION ESPEC[FICA.
17 - SP A08593
-
RIESGO DE QUEMADURAS
_,QU¢: PUEDE OCURRIR?
TOCAR EL METAL EXPUESTO TAL COM© EL CABEZAL DEL
COMPRESOR O LOS TUBOS DE SALIDA DEL ESCAPE, PUEDEOOASlONARLE
SERIAS QUEMADURAS.
&COMO PREVENIRLO?
JAMAS TOQUE PARTES DE METAL EXPUESTAS EN ELCOMPRESOR DURANTE O
INMEDIATAMENTE DESPUt_S DE LAOPERACION. EL OOMPRESOR PERMANECERA
CALIENTEPOR VARIOS MINUTOS LUEGO DE LA OPERACION.
NO LO CUBRA CON FUNDAS PROTECTORAS O INTENTE ELMANTENIMIENTO
HASTA QUE LA UNIDAD HAYA ALCANZADOSU ENFRIAMIENTO.
RIESGO DE PARTES MOVILES
_,QU¢: PUEDE OCURRIR? &COMO PREVENIRLO?
PARTES MOVIBLES TALES COMO LA POLEA, EL VOLANTE Y LACORREA
PODRIAN SER LA CAUSA DE SERIAS LESlONES Sl
ELLAS ENTRARAN EN CONTACTO CON USTED O SUS ROPAS.
INTENTAR OPERAR EL COMPRESOR CON SUS PARTESDAI_IADAS O
FALTANTES, O LA REPARACION DEL COMPRESORCON SUS PROTECCIONES
REMOVIDAS, PUEDE EXPONERLOA USTED A PARTES MOVIBLES, QUE PODRIAN
RESULTAR ENLESIONES SERIAS,
NUNCA OPERE EL COMPRESOR SIN SUS DEFENSAS O SUSCUBIERTAS
REMOVIDAS O DANADAS.
CUALQUIER REPARACION REQUERIDA POR ESTE PRODUCTODEBE SER
EFEOTUADA POR PERSONAL AUTORIZADO DELOS SERVICENTROS.
RIESGO DE CAIDA
_,QU¢: PUEDE OCURRIR? &COMO PREVENIRLO?
UN COMPRESOR PORTATIL PUEDE CAERSE DE LA MESA, ELBANCO DE
TRABAJO O DEL TECHO DAI_IANDO AL OOMPRESOR Y
PUDIENDO RESULTAR EN SERIAS LESlONES O LA MUERTEDEL
OPERADOR.
OPERE SlEMPRE EL COMPRESOR EN UNA POSlClONESTABLE Y SEGURA A FIN
DE PREVENIR EL MOVIMIENTOACCIDENTAL DE LA UNIDAD. JAMAS OPERE EL
COMPRESORSOBRE UN TECHO U OTRA POSlCION ELEVADA. UTILICEMANGUERAS
ADIClONALES DE AIRE PARA ALCANZARPOSlOIONES ALTAS.
RIESGO DE DAI_IOS A LA PROPIEDAD AL TRANSPORTAR
EL COMPRESOR
(Fuego, inhalacion, daho a la superficie de vehiculos}
Para unidades que requieran aceite en la bomba o motores a
gasolina.
_,QU¢: PUEDE OCURRIR? &COMO PREVENIRLO?
DEPOSITE EL COMPRESOR SOBRE UNA ALFOMBRILLA PRO-TECTORA CUANDO
LO TRANSPORTE. A FIN DE PROTEGER AL
VEHfCULO DE Pt_RDIDAS POR GOTEO, RETIRE EL COMPRESORDEL VEHICULO
INMEDIATAMENTE DESPUES DE SU ARRIBO ALDESTINO.
A08593 18- SP
-
Familiaricese con los siguientes t6rminos, antes de operar
launidad:
Cfm: (Cubic feet per minute) Pies ct_bicos por minuto.
SCFM: (Stardardcubic feetper minute)Pies ct_bicosestandarpor
minuto; unaunidadde medida quepermitemedir la canti-dad de
entregade aire.
PSlG: (Poundpersquareinch)Ubrasper pulgadacuadrada.
C6digo de certificaci6n: Los productos que usan una omas de las
siguientes marcas: UL, CUL, ETL, CETL, hansido evaluados pot OSHA,
laboratorios independientes cer-tificados en seguridad, y reOnenlos
est_.ndaressuscriptospor los laboratories dedicados a la
certificaci6n de laseguridad.
Ramal: Circuito el6ctrico que transporta electricidad desdeel
panel de control hasta el tomacorriente.
Esta unidad es suficiente para abastecer de energia el6ctrica a
los siguientes accesorios. Estos se encuentran disponibles atraves
del catalogo para herramientas el_ctricas y manuales, en cualquiera
de los comercios que mantiene la linea completade SEARS.
Accesorios Herramientas para carpinteria
Juegos de conexi6n r_.pida (varias medidas) M_.quina clavadora /
abrochadora
Herramientas pot especialidades
Cepillo neum_tico
Pistola infladora / sopladora
Pistola engrasadora
Pistola para aplicaci6n de sellador
Contenido de la caja de embalaje
1. Compresor de aire con manguera y v_.lvulareguladorade presi6n
(cant. 1)
2. Receptaculo para conexi6n ra.pida(Cant. 1)
3. Enchufe para conexi6n r_pida (Cant. 2)
4. Cinta selladora para rosca (Cant. 1)
5. Pico hembrapara Ilenadode airea los neumaticos(Cant.1)
6. Pistola sopladora (Cant. 1)
7. Boquilla de seguridad (Cant 1)
8. Adaptador para pistola sopladora (Cant. 1)
9. Aguja parainflado (Cant.l)
10. Inflador roscado (Cant. 1)
Para extraer el compresor de aire de su caja
1. Suj6telo de la manija y lev_.ntelo fuera de su caja.
2. Extraiga y descarte todo el embalaje del compre-sor de
aire.
10
19- SP A08593
-
COMO PREPARAR LA UNIDAD
Ubicacion del compresor de aire
Ubique alcompresorde aireen unazona limpia,secay
bienventilada.La bomba del compresorde aire y su carcasahansido
dise_adasparapermitirun
enfriamientoadecuado.Lasaberturasdeventilaci6ndel
compresorresultan- entonces-necesariasparaelmantenimientode
unaadecuadatemperaturadefuncionamiento.No coloque g6neroso
contenedores,enci-ma, nien las proximidadesde dichasaberturas.
INSTRUCCIONES PAPACONECTAR A TIERRA
RIESGO DEDESCARGA
ELECTRICA Ante la eventualidad de un cortocir-cuito, la conexi6n
a tierra reduce el riesgo de elec-trocuci6n proveyendo un conductor
de escapepara la corriente el_ctrica. Este compresor de airedebe
estar adecuadamente conectado a tierra.
El compresor portatil de aire esta equipado con uncable que
tiene un conductor destinado a tierra, conuna espiga apropiada para
su conexi6n (ver las sigu-ientes ilustraciones). El enchufe debe
ser utilizado conun toma corriente que haya sido instalado y
conectadoa tierra de acuerdo a todos los c6digos y
ordenanzaslocales.
1. El cable que acompa_a a esta unidad tiene unaespiga para
conexi6n a tierra. Esta DEBE serutilizada con un tomacorriente
conectado a tierra.
IMPORTANTE: El tomacorriente que ser_.utilizado deberahaber sido
conectado a tierra conforme a todos los c6digoslocales y
ordenanzas.
2. AsegQresede queel
tomacorrientequeserautilizadotengalamismaconfiguraci6nqueelenchufede
conexi6na tierra.NO UTILICE UN ADAPTADOR.Ver figura.
_hufe
/Espiga de conexi6n a tierra
Tomacorrientes"conectados a• tierra
3.
4.
Inspeccioneelenchufey su cord6n antesde cada uso.No usesi
existieransignos deda_os.
Si las instruccionesde conexi6na tierra
nofuerancomple-tamentecomprendidas,o si se estuvieraantela duda
acer-ca de que el compresorestuvieseadecuadamente conec-tado a
tierra, haga verificar la instalaci6n por un elec-tricista
competente.
LA CONEXIONINADECUADA
A TIERRA PUEDE DETERMINAR UNADESCARGA ELI_CTRICA.No modifique el
enchufe provisto. Si el mismono penetrara el tomacorriente
disponible, unelectricista competente deberb instalar
unoapropiado.
La reparacibn del cable o del enchufe DEBERAser efectuada por un
electricista competente.
Cables de extensi6n el_ctrica
Use extensiones de manguera de aire antes que prolonga-ciones de
cables electricos, a fin de prevenir cddas de ten-si6n, perdida de
la potencia eDctrica al motor, y tambi6n surecalentamiento.
Si - no obstante - debe utilizarse una extensi6n de
cable,asegQresede que:
• La extensi6n electrica de 3 conductores, tenga unenchufe de
conexi6n a tierra de 3 hojas, y que existaun receptaculo que acepte
el enchufe del producto.
• Est6 en buenas condiciones.
No m_.slargo que 15,2 m (50 pies).
Calibre 14 (AWG)o mayor. (La medida de los cables seincrementa a
medida que su nQmeroordinal decrece.12, 10, y 8 AWG pueden ser
usados tambien. NO USE16 N118 AWG).
Proteccion del voltaje y del circuito
Acerca del voltaje y la minima cantidad de circuitosrequeridos,
refi6rase al Manual de piezas.
Ciertos compresores de aire pueden ser operados enun circuito de
15 A, siempre que se cumplan las sigu-ientes condiciones:
1. Que el voltaje suministrado a trav6s de losramales del
circuito sea de 15 A.
2. Que el circuito no sea utilizado para alimentar ningunaotra
necesidad el6ctrica (iluminaci6n, artefactos, etc.)
3. Que los cables de extensi6n cumplan con
lasespecificaciones.
4. Que el circuito est6 equipado con un interrupterautom_.tico
de 15 A, o un fusible de acci6n retar-dada de 15 A. NOTA: Si el
compresor estuvieseconectado a un circuito protegido con
fusibles,utilice solamente los de acci6n retardada identifi-cados
come "U".
Si cualquiera de las condiciones enumeradas no pud-iese ser
cumplida, o si el funcionamiento del compre-sor causara reiteradas
interrupciones de la energiacon la que se Io alimenta, podria ser
necesario operaral mismo desde un circuito de 20 A. Para ello no
ser_.necesario cambiar su cable de alimentaci6n.
A08593 20- SP
-
Conozca su compresor de aire
LEA ESTE MANUAL DEL PROPIETARIOY SUS NORMAS DE SEGURIDADANTES DE
OPERARLA UNIDAD. Compare lasilustraciones contra su unidad a fin de
familiarizarse con la ubicaci6n de los distintos controles y
regulaciones. Conserve estemanual para referencias futuras.
Interruptor ON/OFF
Valvula
reguladorapresibn
Pico hembra
para el inflado
de los ,,_neumaticos
rosca
Picos de
_ ::!¢_;°;:_; conex 6n_ " "
ra ,o _ ...._.,_,,,_ .X, Tobera de segundadZbcalo para _ _/_
Adaptador para pistolaconexi6n rapida Inflador c6nico
/ sopladoraAguja para inflar
Descripci6n de operaciones
V&lvula reguladora de presibn: Lavalvulade presi6ncontrolala
cantidadde presi6n que circuladesde el compresorde
airealaccesorio.Lavalvulareguladorade presi6npermite
regularlapresi6nen un tango entre 10y 125 PSI(125 PSIes el valor
depresi6n maselevadoque puede entregarestecompresor).
Interruptor de prendido y apagado (On/Off Iocalizado enel lado
opuesto del compresor de aire): Usado paraprender y apagar el
compresor de aire.
Zbcalo para conexibn r_pida: Facilita el recambio r@idode las
herramientas.
Picos de conexibn r&pida: Instaladossobre las herramientase
insertado en los z6calos de conexi6n r@ida, facilita larapidez del
recambio de las herramientas.
Cinta selladora para filetes de rosca: Usada para aplicarsobre
los filetes a fin de eliminar las perdidas de aire.
Pico hembra para el inflado de los neum_ticos:Adaptador para el
inflado de neumaticos.
Pistola sopladora: Ideal para soplar, limpiar e inflar.
Tobera de seguridad: Previene el incremento de la presi6n.
Adaptador para pistola sopladora: Conectado a la
pistolasopladora o al extremo hembra de la manguera, permite eluso
del pico c6nico del inflador o de la aguja para inflado.
Aguja para inflado: Utilizada para el inflado de
pelotasdeportivas.
Inflador cbnico: Utilizado para el inflado de juguetesinflableso
colchones de aire.
21 - SP A08593
-
COmo utilizar su unidad [ Palanca Adaptador del sopladorI de
manguera
Cbmo detenerla:
1. Coloque la posici6n de la Ilaveinterruptora On/Off en la
posi-ci6n "OFF".
COme utilizar zOcalos,yconectores de conexmnrdpida:
1. Aplique cinta selladora sobrelos filamentos de los z6calosy
conectores rapidos.
2. Ensamble el conector rapidoa la manguera. Enchufe elconector
a la pistola sopladoray al pico hembra parael infladode los
neumaticos. AjOstelo firmemente.EIIo facilitara el cambio de dichos
accesorios.
3. Tire hacia atras la cupla de conexi6n del
acoplamientor_.pidoe inserte el enchufe. Ver la figura de
arriba.
4. Deslice la cupla de acoplamiento a su posicion inicial.
Cbmo utilizar el pico hembra para el inflado delos
neumdticos
1. Conecte a la manguera el pico hembra para inflado
deneumaticos.
2.
3.
4.
Veael parrafo "come poner en marcha" el compresorde aire.
Coloque el pico hembra de inflado de cubiertas sobreel tallo de
la valvula de la cubierta que debe ser infiada.
Incremente lentamente el nivel de presi6n de la
valvulareguladora hasta el valor PSI recomendado por el fabri-cante
de la cubierta. Nota: Para asegurar el valorcorrecto de la presi6n
de inflado, utilice el calibrador depresi6n.
Cbmo utilizar la pistola sopladora
1. Conecte la pistola sopladora a la manguera.
Si no se intenta utilizar accesorioalgunocon la
pistolasopladora,DEBE ensamblarse la boquilla de Boquillade
seguridadseguridad.
2. Ensamble la boquilla de seguridad o el adaptador delextremo
de la manguera a la pistola sopladora. Vea lapr6xima figura.
NOTA" Para poder utilizar la aguja de inflar o el
infladorcSnico,el adaptador del soplador debe estarensambladoa la
pistola sopladora.A08593
Aguja para inflar
Inflador cbnico
Boquilla de seguridad
3. Conecte la aguja para inflar o el inflador c6nico aladaptador
de la pistola sopladora.
4. Vea el parrafo "come poner en marcha" para dararranque al
compresor de aire.
5. Presione la palanca de la pistola sopladora a fin depermitir
el paso del aire.
22 - SP
Antes de comenzar:
2.
3.
Coloqueel interruptorOn/Off en laposici6n "OFF".
Lleve el control de
la presi6n de lava.lvulareguladora ala posici6n 10 PSI.
Conecte mangueras y accesorios.
Demasiada presi6n de airecrea el riesgo de explosi6n.
Verifiquelos valoresmaximos recomendados por elfabricante para
las herramientas de aire y accesorios.Siga cuidadosamente las
instrucciones dadas en"C6mo Poner en Marcha".
Cbmo poner en marcha:
I. Coloque el interruptor On/Off en la posici6n "OFF".
2. Enchufe el cable de energia el6ctrica en un
tomacorrienteconectado a tierra.
3.
4.
5.
Coloque el interruptor On/Off en la posici6n "ON" paradar
arranque al compresor.
Verifique los valores ma.ximosde presi6n admitidos porel
fabricante, para la herramienta neumatica, accesorio ocubierta
neumatica del vehiculo para la que sera usada.La salida de presi6n
del compresor de aire jamas debeexceder los valores de presi6n
estipulados.
Incremente lentamente los valores de presi6n desde elregulador
de la valvula de presi6n. Debera ustedescuchar y percibir la
presi6n del aire que va siendoelevada por acci6n de la valvula
reguladora. Si dichapresi6n no fuese liberada, apague
inmediatamente elcompresor de aire. La va.lvulareguladora de la
presi6ndebera ser reemplazada.
Elaire comprimido provenientede la salida podra contener
condensaci6n de agua. No rode aire sin filtrar sobre unarticulo
que pudiese ser da_ado. AIgunas herramientaso dispositivos
accionados por aire requieren aire filtrado.Lea las instrucciones
dadas para las herramientasneumaticas o los accesorios.
-
Cambio de la manguera de aire
La manguera de aire conectada a su compresor tieneuna
v6.1vulapara su sistema integral de presi6n en elextremo de trabajo
de la manguera. En caso de quefuese necesario el servicio o la
reparaci6n fueserequerida, asegQrese de que la v_.lvula de
regulaci6nde la presi6n se encuentre presente en la manguerade
aire.
NO reemplace lamanguera utilizando la
manguera est_.ndar que no esta equipada con lav6.1vulareguladora
de presi6n. El equipo demanguera apropiado para su compresor
seencuentra disponible en Sears.
No permita que la manguerase retuerza ni sea perforada
en momento alguno. Esto es importante para evitardafios al
compresor y para mantener el control dela v&lvula reguladora de
presi6n.
1. Coloque el interruptor On/Off en la posici6n"OFF" y
desenchufe el conductor el@ctrico.
2. Libere toda la presi6n del cabezal del compresorde aire y de
la manguera, girando la v_.lvula depresi6n regulable a 10 PSI.
3. Proteja el conductor el@ctrico y la manguera deaire de
dafios, dobl_.ndolos flojamente alrededordel compresor de aire.
4. Guarde el compresor de aire en un sitio limpio yseco.
23- SP A08593
-
Las fuentes de tensi6n, partes en movimiento o fuentes de aire
comprimido quedanexpuestas al reparar el compresor. EIIo podria
ocasionar lesiones personales.
Desenchufe el compresor antes de intentar cualquier
reparaci6n.
PROBLEMA
P6rdidas de aire
El compresor no entregasuficiente aire
CAUSA
Conexi6n suelta de la manguera
Uso excesivamente prolongadodel aire
CORRECClON
Ajustar la conexi6n
Disminuirla cantidadde uso deaire. Sucompresor no tiene
suficiente capacidad paralos requerimientosdeaire a los que
estasiendo sometido.
El motor no trabaja
AIta presi6n de descarga. No puedeser reducida.
Orificio en la manguera
Orificio en la manguera
Estall6 el fusible; se dispar6 elinterruptor autom_.tico.
El cable de extensi6n electrica tieneuna Iongitud o calibre
err6neos.
Conexiones el6ctricas sueltas.
Fallas del motor.
La v_.lvulade regulaci6n de la presi6nno funciona,
Reemplace la manguera.
Ajuste las conexiones
1.
2.
3.
4.
5.
Verifique la caja de fusiblesinspeccionando la existencia
defusibles fundidos, y reemplace losnecesarios. Restablezca la
posi-ci6n del interruptor automa.ticodel circuito. No utilice un
fusible ointerruptor automatico de mayorvalor que el especificado
para elramal de su circuito.
Verifique que el fusible sea eladecuado. Debe utilizar
fusiblesde acci6n retardada.
Verifique el problema del sumin-istro de bajo voltaje.
Verifique la extensidn del conduc-tor el6ctrico.
Desconecte los otros artefactosel_ctricos que estuvieren
operan-do en el ramal del circuito que lecorresponde al
compresor.
Verifique la extensi6n del conductorel6ctrico.
Verifique la conexi6n en la caja terminal
Contacte a un tecnico calificado enservicio
Riesgode
explosi6n. NO opere el compresor sieste problema existiera.
Debera reem-plazarse la valvula de regulaci6n de lapresi6n.
A08593 24 - SP
-
25-SP A08593
-
A08593 26-SP
-
27-SP A08593
-
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_HHHHHHHHH
iiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii,,,iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Your Home
For repair- in your home - of all major brand appliances,lawn
and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories andowner's manuals that
you need to do-it-yourself.
For Sears professional installation of home appliancesand items
like garage door openers and water heaters.
1-800-4-MY-HOME ® Anytime, day or night(1-800-469-4663) (U.S.A.
and Canada)www.sears.com www.sears.ca
Our Home
For repair of carry-in products like vacuums, lawn equipment,and
electronics, call or go on-line for the nearest
Sears Parts and Repair Center.
1-800-488-1222 Anytime, day or night (U.S.A.
only)www.sears.com
To purchase a protection agreement (U.S.A.)or maintenance
agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparaciona domicilio, y para ordenar
piezas:
Au Canada pour service en fran(_ais:
1-800--LE-FOYER Mc(1-800-533-6937)www.sears.ca
6 AR, © Sears, Roebuck and Co.
® Registered Trademark / TMTrademark / SMService Mark of Sears,
Roebuck and Co.
® Marca Registrada / TMMarca de Fa.brica / SMMarca de Servicio
de Sears, Roebuck and Co.
MCMarque de commerce / MDMarque depos6e de Sears, Roebuck and
Co.