ExamReal.Brocade.150-130.v20131025.113q

Brocade.150-130.v20131025.113q

Vendor : Brocade

Exam Name : Brocade Certified Network Engineer 2012

Exam Code : 150-130

For Full Set of Questions Please Visit : http://www.ExamReal.com/XXXX.html

Exam A

QUESTION 1Which three transceiver form factors are supported by Brocade switches and routers? (Choose three.)

A. XPAK

B. SFP

C. SFP+

D. X2

E. XFP

Correct Answer: BCE

QUESTION 2Which type of transceiver would be used to support a 5 km single mode fiber 10 Gbps connection?

A. SFP

B. SFP+

C. GBIC

D. SFM

Correct Answer: B

QUESTION 3Two sites 8 km apart will be connected together using fiber optic cable. Which SFP/cable combinationneeds to be used?

A. short reach SFP with multi-mode fiber

B. short reach SFP with single-mode fiber

C. long reach SFP with multi-mode fiber

D. long reach SFP with single-mode fiber

Correct Answer: D

QUESTION 4A powered device connected to a Brocade FastIron device has been auto discovered and classified as aclass-3 PoE device. However, its power consumption is only 10 watts. Which command would be used onthe FastIron to reallocate power back to the available power budget, while still providing all the necessarypower to the powered device?

A. no legacy-inline-power

B. inline power power-by-class 2

C. inline power priority 2

D. inline power power-limit 11000

Correct Answer: D

QUESTION 5Which two Layer 2 network discovery protocols are used to detect PoE power requirements?

(Choose two.)

A. FDP

B. LLDP-MED

C. LACP

D. CDP

Correct Answer: BD

Brocade 150-130 Exam | ExamReal.com

Contact Us : [email protected] Get Success in Passing Your Certification Exam at first attempt

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

QUESTION 6What are two Brocade stackable products? (Choose two.)

A. Brocade Fastiron SX

B. Brocade FastlronCX

C. BrocadelCX6430

D. Brocade MLXe

Correct Answer: BC

QUESTION 7What are two Brocade products that are designed for use in a service provider network? (Choose two.)

A. Brocade Fastlron SX

B. Brocade MLXe

C. Brocade Netlron CER 2000

D. Brocade FCX

Correct Answer: BC

QUESTION 8You have just configured a new Multi-Chassis Trunk between two Brocade MLXe chassis.

Which protocol information will be distributed across this link?

A. IPv6

B. BGP

C. RIPv2

D. STP

Correct Answer: D

QUESTION 9You have just purchased 22 new Brocade Fastlron FCXs. You want to take advantage of BrocadeIronStack technology to make as many of the FCXs appear as a single stack as possible.What is theminimum number of Brocade IronStacks required?

A. 1

B. 2

C. 3

D. 5

Correct Answer: C

QUESTION 10What are two supported stacking topologies for the Brocade IronStack technology? (Choose two.)

A. ring

B. linear

C. bus

D. star

Correct Answer: AB

QUESTION 11The traffic volume received by your network clients is higher than desired.



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Which two features will help reduce the amount of unwanted traffic? (Choose two,)

A. ACL

B. VRRP-E

C. BPDU Guard

D. IGMP Snooping

Correct Answer: AD

QUESTION 12You have been asked to implement a standards-based Layer 2 loop avoidance protocol with a typicalconvergence time of 3 seconds or less. Which Layer 2 loop avoidance protocol should you use?

A. 802.1q

B. 802.1D

C. MRP

D. RSTP

Correct Answer: D

QUESTION 13What are two valid BPDU types in Spanning Tree 802.1D? (Choose two.)

A. Configuration BPDU

B. Root Override BPDU

C. Failure Notification BPDU

D. Topology Change Notification BPDU

Correct Answer: AD

QUESTION 14Which statement is correct concerning Layer 2 frame forwarding?

A. Unknown unicast frames are flooded out all ports except the ingress port,

B. Multicast frames are forwarded to a specific destination.

C. Unicast frames are forwarded to multiple ports.

D. Broadcast frames are flooded to a select number of ports.

Correct Answer: A

QUESTION 15Which two features enable discovery of network switches? (Choose two.)

A. LLDP

B. UDLD

C. FDP

D. LFS

Correct Answer: AC

QUESTION 16You want the links between two switches to forward traffic for more than one VLAN.

What should you use to configure the inter-connected ports?

A. load sharing

B. tagged



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

C. untagged

D. ISL

Correct Answer: B

QUESTION 17Which three statements are true when configuring virtual routing interfaces? (Choose three.)

A. A single virtual interface can be used to route traffic between all VLANs within the same switch.

B. Each VLAN on a switch requires its own virtual interface.

C. A virtual interface can be a member of multiple VLANs.

D. A virtual interface can have multiple IP addresses.

E. Hosts in a VLAN can use the IP address of the virtual interface as their default gateway.

Correct Answer: BDE

QUESTION 18You are configuring multiple VLANs using only untagged ports on two switches. Which statement is true?

A. All traffic between switches will use 802.lq.

B. AII VLAN traffic can use a single untagged uplink port.

C. Untagged ports can be placed into multiple VLANs.

D. Each VLAN requires a dedicated uplink between switches.

Correct Answer: D

QUESTION 19Which two statements about LAGs are true? (Choose two.)

A. A LAG provides load-sharing.

B. A LAG provides sub-microsecond failover,

C. A LAG can contain links of different speeds.

D. A LAG is treated as a single logical link by the switch.

Correct Answer: AD

QUESTION 20On a Brocade MLXe device, which three conditions must be met for a LAG to form? (Choose three.)

A. AII ports configured in a LAG are of equal bandwidth.

B. Ports must have different untagged VLANs.

C. A LAG must have the primary port selected before it can be deployed.

D. AII ports configured in a LAG must reside in the same VLANs.

E. LACP forwarding must be disabled on the primary port and enabled on one or more of the secondaryports.

Correct Answer: ACD

QUESTION 21Which two results does the link-aggregate configure key <number> command accomplish when creatingLink Aggregation Groups (LAGs) on a FastIron device? (Choose two.)

A. It encrypts the LAGs for security,

B. It identifies LAG membership.

C. It allows multiple LAGs to be configured on a device.

D. It is used to configure VLANs on the LAG.



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Correct Answer: BC

QUESTION 22Which two destination addresses are used in an ARP request if the source station's IP address is:

192.168.5.12/16? (Choose two.)

A. 192.168.5.255

B. FF:FF:FF:FF:FF:FF

C. 00:19:B9:FF:FF:FF

D. 192.168.255.255

Correct Answer: BD

QUESTION 23Which type of message is exchanged between switches to prevent loops and maintain loop-freetopologies?

A. LACP

B. BPDU

C. UDLD

D. FDP

Correct Answer: B

QUESTION 24Which three types of network addresses are supported in IPv6? (Choose three.)

A. multicast

B. broadcast

C. anycast

D. unicast

E. ANAT

Correct Answer: ACD

QUESTION 25Given the command output shown below:

de(config)#mirror-port ethernet 1/2/4

Brocade(config)#interface ethernet 1/2/11

Brocade(config-if-e100-11)#monitor ethernet 1/2/4 both

What do the Brocade commands accomplish?

A. They allow all traffic on interface ethernet 1/2/11 to be replicated on interface ethernet 1/2/4 for analysis

B. They allow ingress only traffic on interface ethernet 1/2/4 to be replicated on interface Ethernet 1/2/11for analysis.

C. They allow all traffic on interface ethernet 1/2/4 to be replicated on interface ethernet 1/2/11 foranalysis.

D. They allow egress only traffic on interface ethernet 1/2/4 to be replicated on interface Ethernet 1/2/11for analysis.

Correct Answer: A

QUESTION 26Why would the IP SSH port <number> command be used?



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. This command is used to restrict certain port numbers from being used with SSH.

B. This command is used to change the default port number used by SSH.

C. This command is required before SSH will respond to any port.

D. This command is used to set a range of port numbers to be used by SSH.

Correct Answer: B

QUESTION 27Why would the IP SSH port <number> command be used?

A. This command is used to restrict certain port numbers from being used with SSH.

B. This command is used to change the default port number used by SSH.

C. This command is required before SSH will respond to any port.

D. This command is used to set a range of port numbers to be used by SSH.

Correct Answer: B

QUESTION 28What are two ways that TACACS+ differs from TACACS? (Choose two.)

A. TACACS + uses TCP.

B. TACACS + uses UDP.

C. TACACS + encrypts traffic between the Brocade device and the server.

D. TACACS + does not encrypt traffic between the Brocade device and the server

Correct Answer: AC

QUESTION 29You have to implement a security protocol that encrypts all traffic between the Brocade device and theauthentication server.

Which security protocol would you use to support this requirement?

A. TACACS+

B. TACACS

C. RADIUS

D. AAA

Correct Answer: A

QUESTION 30Which two protocols would be used to transfer new code to a Brocade FastIron, TurboIron, or NetIrondevice? (Choose two.)

A. FTP

B. TFTP

C. SFTP

D. SCP

Correct Answer: BD

QUESTION 31You have lost the super-user password to your Brocade device. You need to recover the device andbypass the password, using the serial console. Which command must you issue after you interrupt theboot sequence?

A. confreg 0x2142



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

B. boot system password-bypass

C. password recover

D. no password

Correct Answer: D

QUESTION 32You have a LAG configured and are having problems with the logical interface coming online.

What would cause this?

A. One end of the LAG is a Brocade FastIron stack.

B. The LAG members are made up of 1 Gbps and 10 Gbps ports.

C. The LAG includes members that are not consecutive (ports 1, 2, and 4).

D. AII members of the LAG are configured as static.

Correct Answer: B

QUESTION 33



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Users connected to Switch1 are unable to access a database server connected to Switch2.

Referring to the exhibit, what are three explanations? (Choose three.)

A. Port 1/1/1 on Switch2 is administratively disabled.

B. Port 1/1/1 on Switch1 is administratively disabled.

C. One of the switches has a defective port.

D. The cable between the two switches is damaged.

E. Port 1/1/1 on Switch1 has Spanning Tree disabled.

Correct Answer: ACD

QUESTION 34Brocade support has requested that you gather supportsave data for troubleshooting an issue on aBrocade FastIron ICX. Which service is required to transfer the files?



www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. A server with SFTP that is reachable by the Brocade FastIron ICX.

B. An FTP server that is reachable by the Brocade FastIron ICX.

C. A TFTP server that is reachable by the Brocade FastIron ICX.

D. A RADIUS server that is reachable by the Brocade FastIron ICX.

Correct Answer: C

QUESTION 35You have been informed a group of remote employees are unable to authenticate with the RADIUS server.From the Brocade FCX router, you enable the debug dot1x events command.

Which three events will be viewed? (Choose three.)

A. authentications failed

B. authentications succeeded

C. ACLs requested by the RADIUS server.

D. standard ACL requests

E. extended ACL requests

Correct Answer: ABC

QUESTION 36You need to expedite a case to Brocade support for troubleshooting. What information is needed?(Choose three.)

A. topology diagram

B. recent changes

C. show tech-support output

D. errordump output

E. RASlog

Correct Answer: ABC

QUESTION 37A customer work group notifies you that they are trying to reach a custom application on a server.

The server is in a different IP domain. You have verified that the application is up. You can successfully runping and traceroute to the server from the workgroup workstations. What would you look for next?

A. a MTU mismatch problem

B. a mis-configured router port

C. a blocked UDP/TCP port

D. a corrupt TCP session

Correct Answer: C

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Exam

QUESTION 1What are two valid ways to represent the IPv6 address 2001:0000:0000:0200:002D:D0FF:FE48:4672?(Choose two.)

A. 2001::02:002D:D0FF:FE48:4672

B. 2001:0:0:0200:002D:D0FF:FE48:4672

C. 2001::0200:002D:D0FF:FE48:4672

D. 21::0200:002D:D0FF:FE48:4672

Correct Answer: BC

QUESTION 2An identical route has been discovered by OSPF and RIP. By default, the OSPF route is chosen andadded to the routing table. What should be done to allow the RIP route to be preferred?

A. Redistribute OSPF routes into RIP.

B. Change the administrative distance.

C. Raise the route's priority in RIP.

D. Use the no router OSPF command.

Correct Answer: B

QUESTION 3When configuring an IP static route in a Brocade router, which three parameters are required?

(Choose three.)

A. IP address of destination

B. administrative distance for the route

C. next hop

D. subnet mask

E. the metric for the route

Correct Answer: ACD

QUESTION 4When using CIDR notation, what is the default route in an IPv6 configuration?

A. ::/0

B. 1001:ffff:0:0:0:0::Vl28

C. 1001:ffff:0:0:0::y0

D. ffff::/36

Correct Answer: A

QUESTION 5During the discovery process, to which registered multicast IP address does OSPF send a hello packet?

A. 224.0.0.5

B. 224.0.0.100

C. 224.0.0.2

D. 224.0.0.6

Correct Answer: A

QUESTION 6

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

In which stage is an OSPF neighbor adjacency complete?

A. loading

B. exchange

C. two-way

D. full

Correct Answer: D

QUESTION 7Which three parameters must match for two OSPF routers to become neighbors? (Choose three.)

A. router ID

B. subnet mask

C. area ID

D. hello/dead intervals

E. bridge ID

Correct Answer: BCD

QUESTION 8In a DR/BDR election, what will be the result for Router 1 based on the information shown in the exhibit?

A. Router 1 will not participate in the election.

B. Router 1 will participate in the election but will not become either the DR or BDR.

C. Router 1 will become the DR based on having the lowest priority value.

D. Router 1 will become the DR based on having the lowest interface IP address.

Correct Answer: A

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

QUESTION 9Your company uses OSPF and has recently purchased another company that uses RIP.

Management requires that routes between the two companies be shared without interrupting services oneither network. How is this implemented?

A. Enable route redistribution in both RIP and OSPF on the DR.

B. Enable route redistribution in both RIP and OSPF on the BDR.

C. Enable route redistribution in both RIP and OSPF on the ASBR.

D. Enable route redistribution in both RIP and OSPF in the ABR.

Correct Answer: C

QUESTION 10The multicast IP address 239.10.20.30 is mapped to which MAC address?

A. 00-00-ef-0b-15-1f

B. 00-00-5e-0a-14-1e

C. 01-00-ef-0b-15-1lf

D. 01-00-5e-0a-14-1e

Correct Answer: D

QUESTION 11Which two multicast routing protocols are supported on Brocade FastIron devices? (Choose two.)

A. DVMRP

B. PIM

C. MBGP

D. MOSPF

Correct Answer: AB

QUESTION 12An engineer wants to implement Policy Based Routing (PBR). The IP address block to be matched is100.100.100.128/25. Which ACL would match the traffic affected by PBR?

A. access-list 51 permit 100.100.100.128 0.0.0.127

B. access-list 51 deny 100.100.100.128 0.0.0.127

C. access-list 51 permit 100.100.100.0 0.0.0.127

D. access-list 51 deny 100.100.100.0 0.0.0.127

Correct Answer: A

QUESTION 13What is the numeric range for standard ACL IDs?

A. 0 - 99

B. 0 -100

C. 1-99

D. 1-100

Correct Answer: C

QUESTION 14Which two access control list (ACL) types will match on TCP/UDP ports? (Choose two.)

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. numbered standard ACLs

B. numbered extended ACLs

C. named standard ACLs

D. named extended ACLs

Correct Answer: BD

QUESTION 15You have configured your Brocade device as shown in the exhibit.

***Exhibit is Missing***

Which statement is correct regarding interface Ethernet 10 on this device having inbound traffic from172.17.1.1/24 to 172.17.2.1/24 on port 21?

A. It would be permitted.

B. It would be denied by the implicit deny statement.

C. It would be denied by FTP port 21.

D. This ACL only applies to outbound traffic.

Correct Answer: A

QUESTION 16Which two statements are true about QoS when implemented on a Brocade FastIron platform?

(Choose two.)

A. Packets with lower priority classifications are given a higher precedence for forwarding.

B. Packets with higher priority classifications are given a higher precedence for forwarding.

C. Stackable devices use CoS 0 for stacking communication.

D. Stackable devices use CoS 7 for stacking communication.

Correct Answer: BD

QUESTION 17You want to classify and mark traffic at the edge of your network before it is sent to the core and routedwhere Layer 3 QoS is trusted and enabled. Which type of marking should you configure to ensure yourapplication traffic is serviced correctly in the core of your network?

A. Mark the 802.lp field according to application priority

B. Mark the PCP field according to application priority

C. Mark the EXP field according to application priority

D. Mark the DSCP field according to application priority

Correct Answer: D

QUESTION 18You have a mission-critical application on your network that you know by IP address. You want this trafficto be serviced before all other traffic on the network. Which two features should you implement to ensurethat this mission-critical application traffic is identified and serviced correctly? (Choose two.)

A. Configure an access control list to classify the traffic.

B. Configure RADIUS to authenticate the traffic going over the network.

C. Configure rate shaping for the ports across which the traffic is traveling.

D. Configure strict priority for the queue in which the traffic resides.

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Correct Answer: AD

QUESTION 19Which version of Simple Network Management Protocol (SNMP) supports the Advanced EncryptionStandard (AES)?

A. SNMPv1

B. SNMPv2

C. SNMPv2c

D. SNMPv3

Correct Answer: D

QUESTION 20Your Brocade network monitoring solution includes the requirements for random sampling of packets andtime-based sampling of counters.

You have been asked to determine an appropriate solution.

What will fulfill the specified requirements?

A. sFlow

B. RMON1

C. RMON2

D. Netflow

Correct Answer: A

QUESTION 21Which two protocols would be used to back up a Brocade device configuration? (Choose two.)

A. FTP

B. SCP

C. TFTP

D. FTPS (FTP-SSL)

Correct Answer: BC

QUESTION 22What is the purpose of the Brocade MLXe SNMP trap hold-down timer?

A. to send all traps before a router reboot

B. to wait for convergence to occur before sending traps

C. to wait for UDP connection establishment before sending traps

D. to wait for TCP connection establishment before sending traps

Correct Answer: B

QUESTION 23You have been informed that you will need to implement 802.IX on all Brocade switches and routers.

Which three are required to support this request? (Choose three.)

A. applicant

B. supplicant

C. authenticator

D. authentication server

E. supplicant server

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Correct Answer: BCD

QUESTION 24Given the following configuration:

Brocade(config)# aaa authentication enable default radius tacacs telnet local

What is the primary authentication method being used for Privileged EXEC mode and CONFIG

level access?

A. local

B. telnet

C. TACACS

D. RADIUS

Correct Answer: D

QUESTION 25What does the command copy flash tftp 192.168.13.37 FGSR07001.bin secondary do?

A. It copies the code contained in the secondary flash partition to a TFTP server located at 192.168.13.37.

B. It copies the configuration contained in the secondary flash partition to a TFTP server located at192.168.13.37.

C. It copies the code contained on a TFTP server located at 192.168.13.37 to the secondary flashpartition.

D. It copies the configuration contained on a TFTP server located at 192.168.13.37 to the secondary flashpartition.

Correct Answer: Awww.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Exam

QUESTION 1On Brocade FastIron, TurboIron, and Netlron platforms, which command saves the running configurationto the flash's startup configuration?

A. write memory

B. copy running-config startup-config

C. config commit

D. config save

Correct Answer: A

QUESTION 2In the exhibit, which port is responding to a change in the network topology?

A. port 1

B. port 2

C. port 3

D. port4

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Correct Answer: A

QUESTION 3Optical monitoring is not returning data. What are three reasons for this happening? (Choose three.)

A. The optic module does not support optical monitoring.

B. It is only supported on LR optics.

C. The port is configured as a stacking port.

D. The port is in use.

E. The port is down.

Correct Answer: ACE

QUESTION 4You have inherited the routing redundancy configuration shown in the exhibit. Router A is the currentVRRP-E master. Your network is not failing over to router B. What needs to be added to configure router Bas a backup and maintain the current master?

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. backup priority 100 track-priority 20

B. backup priority 110 track-priority 20

C. backup priority 120 track-priority 20

D. backup priority 130 track-priority 20

Correct Answer: A

QUESTION 5You are configuring a keep-alive VLAN for a Multi-Chassis Trunking deployment on two new

Brocade MLXe chassis. You notice that STP and VLANs are not valid configuration options.

What have you overlooked during the configuration?

A. You need to include no route-only.

B. You need to include trunk deploy.

C. You need to include deploy.

D. You need to include route-only.

Correct Answer: A

QUESTION 6You need to troubleshoot problems with an optic connection on a Brocade MLXe device.

What information is displayed by show optic <slot> for each port on that slot? (Choose three.)

A. This command displays the temperature information for the optic.

B. This command displays the transmit power information for the optic.

C. This command displays the number of interface flaps for the optic.

D. This command displays the receive power information for the optic.

E. This command displays the length of the fiber cable.

Correct Answer: ABD

QUESTION 7Referring to the exhibit, port eth 1 on Switch-A is connected to port eth 1 on Switch-B.


You notice high packet loss between the two devices communicating over this link.

What is causing high packet loss over this link?

A. BPDU Guard is enabled on Switch-A but disabled on Switch-B.

B. The two ports are not a member of any active trunks.

C. The port on Switch-A is 10 GbE while the port on Switch-B is 1 GbE.

D. The MTU values on Switch-A and Switch-B do not match.

Correct Answer: D

QUESTION 8Referring to the exhibit, requests from Client A are being seen on Server D but responses are not making itback to Client A.


www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

What are two methods that will resolve the issue? (Choose two.)

A. Redistribute directly connected routes in OSPF on Router B.

B. Change the gateway on IP route entry 3 on Router C from 10.5.5.1 to 10.0.0.1.

C. Change the cost on IP route entry 3 on Router C from 1 to 10.

D. Add a static route on Router C with destination 10.0.0.0/24 with gateway 10.5.5.1.

Correct Answer: AD

QUESTION 9Referring to the exhibit, why are interfaces 1/3, 1/5 and 1/7 blocked on Switch C?

A. Switch A is the root bridge.

B. Switch B is the root bridge.

C. Switch C is the root bridge.

D. Path cost for interfaces 1/3, ly5 and 1/7 are unequal.

Correct Answer: A

QUESTION 10Referring to the exhibit, which command must be entered to make the LAG function on a

Brocade NetIron MLXe?

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. deploy

B. enable

C. forward-Iacp

D. Iacp-cfg-det-dis

Correct Answer: A

QUESTION 11

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Fiber optic cabling is immune to which type of signal degradation?

A. attenuation

B. noise

C. EMI

D. leakage

Correct Answer: C

QUESTION 12Which type of transceiver would be used to support a 1 km multi-mode fiber 1 Gbps connection?

A. SFP

B. SFP+

C. Twinax

D. QSFP

Correct Answer: A

QUESTION 13A customer wants to use a cable that provides maximum EMI protection. Which type of cable should beused?

A. UTP

B. STP

C. CAT3

D. copper

Correct Answer: B

QUESTION 14What is the minimum cabling requirement for PoE+?

A. Category 2

B. Category 3

C. Category 4

D. Category 5

Correct Answer: D

QUESTION 15Which two Brocade products are recommended for use in a campus access environment?

(Choose two.)

A. BrocadeMLXe

B. Brocade TurboIron 24X

C. Brocade FCX

D. BrocadelCX6430

Correct Answer: CD

QUESTION 16Which two Brocade products are recommended for core/aggregation use? (Choose two.)

A. BrocadeMLXe

B. Brocade FastIron WS

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

C. Brocade NetIron CER 2000

D. Brocade FastIron SX

Correct Answer: AD

QUESTION 17Which two statements about ICL links in Brocade Multi-Chassis Trunk (MCT) implementations are true?(Choose two.)

A. ICL links connect the two MCT chassis and allows MCT clients to see both devices as a single

device.

B. ICL links connect the MCT client devices to the MCT logical chassis.

C. ICL links are necessary for the two devices to form an MCT cluster.

D. ICL links allow the MCT logical chassis to communicate with a non-MCT device.

Correct Answer: AC

QUESTION 18Which two features are implemented using Brocade IronStack technology? (Choose two.)

A. You can use any port on the switches to create your IronStack.

B. You can mix devices running different software images in the same stack group.

C. You can manage multiple physical switches in an IronStack as a single logical switch.

D. You can perform a hitless stack failover without impacting Layer 2 and Layer 3 unicast traffic.

Correct Answer: CD

QUESTION 19A client had ports 1/3/1 and 1/3/2 on the Brocade FCX go down because of errors being received from theupstream switch. The client repaired the upstream switch but the ports of the FCX are still down.

Referring to the command output shown above, what does the client need to do to bring up the links?

A. Enable the ports.

B. Restart spanning tree.

C. Restart the routing protocol.

D. Reseat the cables for each port.

Correct Answer: A

QUESTION 20Which two enhanced spanning tree features help prevent rogue hijacking of a spanning tree root bridge?(Choose two.)

A. SSTP

B. Root Guard

C. PVST

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

D. BPDU Guard

Correct Answer: BD

QUESTION 21What are two characteristics of an IEEE 802.ID root bridge? (Choose two.)

A. The lowest bridge ID has the highest priority for root bridge selection.

B. The root bridge must be enabled on Brocade Layer 2 code.

C. The bridge ID for root bridge selection is a combination of the bridge priority and MAC address.

D. The root bridge calculates the path cost to all other switches to determine which ports will be used andwhich will be blocked.

Correct Answer: AC

QUESTION 22

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

In the exhibit, the network is running Spanning Tree 802.ID. Which port will be placed in a blocked state?

A. Switch 1 port 1

B. Switch 1 port 2

C. Switch 2 port 1

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

D. Switch 2 port 2

Correct Answer: D

QUESTION 23What happens to Ethernet frames that enter a switch with MAC learning disabled on all interfaces?

A. AII incoming frames will be dropped.

B. AII incoming frames will be flooded.

C. Unicast frames will be dropped; multicast and broadcast frames will be flooded.

D. Multicast and broadcast frames will be dropped; unicast frames will be flooded.

Correct Answer: B

QUESTION 24

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Referring to the exhibit, an Ethernet frame enters Switch A, port e1 with destination address:

0005.3392.a30d.

What describes how Switch A will process the frame?

A. The frame will be sent out port e2.

B. The frame will be sent out port e3.

C. The frame will be sent out ports e2 and e3.

D. The frame will be trapped to the CPU and the destination address changed to 0005.1e00.000c.

Correct Answer: B

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

QUESTION 25What are three types of private VLANs supported on a Brocade Fastlron? (Choose three.)

A. primary

B. isolated

C. community

D. broadcast

E. managed

Correct Answer: ABC

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

Exam

QUESTION 1Which IPv6 address is correctly formatted?

A. 2001:0000:130F:0000:0000:00A2:987B:12FC

B. 2001::130F::00A2:987B:12FC

C. 2001:0000:130F:0000:00CD:0000:00A2:987B:12FC

D. 2001:0000:130F:0000:00A2:987B:12FC

Correct Answer: A

QUESTION 2Exhibit as:

Which technology allows a service provider the ability to connect customer sites with duplicate taggedVLAN configurations across the same circuit as shown in the exhibit?

A. dual-mode

B. 802.1q

C. untagged

D. Q-in-Q

Correct Answer: D

QUESTION 3What are two uses for port-based VLANs? (Choose two.)

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. Create separate broadcast domains inside a single Layer 2 network.

B. Segregate traffic at Layer 3.

C. Eliminate the need for routers between different subnets.

D. Separate user traffic into different logical network segments based on department.

Correct Answer: AD

QUESTION 4OU need to improve redundancy in your LAN as well as increase bandwidth between switches using aLayer 2 protocol.

Which feature will provide this?

A. LLDP

B. LACP

C. VRRP

D. SSTP

Correct Answer: B

QUESTION 5What are two methods that a Brocade device can be configured for load sharing? (Choose two.)

A. per port

B. per packet

C. hash based

D. per second

Correct Answer: BC

QUESTION 6A workstation wants to send a packet to a destination that is not on the same network. Which

destination MAC address will the workstation use to send the packet?

A. destination MAC address

B. gateway's MAC address

C. multicast address

D. broadcast address

Correct Answer: B

QUESTION 7Which three network ranges did IETF allocate to be used as IPv4 private networks? (Choose three.)

A. 10.0.0.0/3

B. 192.168.0.0/16

C. 172.16.0.0/16

D. 172.16.0.0/12

E. 192.168.0.0/24

Correct Answer: ABD

QUESTION 8Which three statements are true about RIPv2 and OSPF? (Choose three.)

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. RIPv2 is a distance vector and OSPF is a link state protocol.

B. OSPF supports VLSM and RIPv2 does not.

C. RIPv2 and OSPF support MD5 authentication.

D. RIPv2 advertises its entire routing table and OSPF sends only updates.

E. RIPv2 and OSPF use neighbor statements to configure peers.

Correct Answer: ACD

QUESTION 9What are three ways that VRRP is different from VRRP-E? (Choose three.)

A. VRRP is a standards-based protocol described in RFC 2338; VRRP-E is a proprietary Brocadeprotocol.

B. VRRP-E is a standards-based protocol described in RFC 2338; VRRP is a proprietary Brocadeprotocol.

C. In VRRP, there is no "owner" router.

D. In VRRP-E, there is no restriction on which the router can be the default master.

E. VRRP-E sends multicast hello packets to the "all routers" multicast address 224.0.0.2.

Correct Answer: ADE

QUESTION 10What are two benefits achieved by using a loopback interface on a Brocade router? (Choose two.)

A. The router ID does not change.

B. It allows remote connectivity to a router.

C. It provides next-hop for neighbors.

D. It does not belong to a physical interface.

Correct Answer: AD

QUESTION 11You are requested to design a network that requires a minimum of five subnets with a minimum of 16 hostsper subnet.

With the class C network of 200.101.192.0, which subnet mask would be used to fulfill theserequirements?

A. /25

B. /26

C. /27

D. /28

Correct Answer: C

QUESTION 12What is the CIDR notation for the IP address range: 192.115.0.0 -192.115.3.255?

A. 192.115.0.0/22

B. 192.115.0.0/24

C. 192.115.0.1/22

D. 192.115.0.1/24

Correct Answer: A

QUESTION 13What is the default administrative distance for RIP?

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

A. 1

B. 110

C. 115

D. 120

Correct Answer: D

QUESTION 14Which OSPF area is created when the area 51 stub no-summary command is issued?

A. normal area

B. not so stubby area

C. stub area

D. totally stubby area

Correct Answer: D

QUESTION 15When is an OSPF virtual link used?

A. When an area has no direct connection to the backbone area.

B. When an area needs access to an ASBR.

C. When an area is configured as a stub area.

D. When an area needs to connect to a non-backbone area.

Correct Answer: A

QUESTION 16What are two functions of an OSPF Autonomous System Boundary Router (ASBR)? (Choose two.)

A. The router can run multiple routing protocols.

B. The router redistributes routes between OSPF areas within an AS.

C. The router redistributes non-OSPF routes into an OSPF AS.

D. The router connects one or more OSPF areas to the OSPF backbone.

Correct Answer: AC

QUESTION 17You are implementing an OSPF network with five defined areas. You want to configure OSPF area routesharing to other specified OSPF areas.

Which router will you need to configure to share area routes with other area routes?

A. ABR router

B. BDR router

C. DR router

D. BGP router

Correct Answer: A

QUESTION 18What are the two ways that IGMP is used? (Choose two.)

A. It can be sent by a host to indicate its interest of joining a specific multicast group.

B. It can be sent among routers to exchange multicast routing information.

C. It can be used to specify packet forwarding methods for a specific multicast group.

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

D. It can be sent by a router to query multicast listeners on a given subnet for all multicast groups.

Correct Answer: AD

QUESTION 19What is the default implicit behavior at the end of an ACL?

A. log

B. permit any

C. deny any

D. remark

Correct Answer: C

QUESTION 20A customer uses an access control list (ACL) to restrict access to servers on their network. The

ACL properly restricts traffic. However, the customer has no visibility to which IP addresses were denied bythe ACL. Which word added to the end of the ACL statement would solve this problem?

A. log

B. permit

C. snmp

D. syslog

Correct Answer: A

QUESTION 21Which two statements about ingress extended ACLs are correct? (Choose two.)

A. They use extended ACL IDs 200 - 299.

B. They save network resources by reducing traffic.

C. They eliminate denial of service (DoS) attacks.

D. They block unwanted traffic or users.

Correct Answer: BD

QUESTION 22Which statement is true of an access control list (ACL) on a Brocade IP device?

A. Only outbound ACLs can be used on any Brocade IP device.

B. The ACL takes effect immediately after being applied to an interface.

C. An ACL is immediately applied to all physical interfaces once the ACL is configured.

D. Standard ACLs can be used to control traffic inbound or outbound based on source and destinationaddresses.

Correct Answer: B

QUESTION 23When 802.lp priority override is enabled on the primary port of a trunk group, which other ports of the trunkgroup will be affected?

A. all ports except the primary trunk port

B. some of the trunk ports

C. only the primary port of the trunk group

D. all ports of the trunk group

Correct Answer: D

www.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

QUESTION 24What are the three available QoS scheduling algorithms available on Brocade NetIron and FastIronproducts? (Choose three.)

A. weighted round robin

B. strict priority

C. first-in-first-out

D. hybrid

E. deficit round robin

Correct Answer: ABD

QUESTION 25Which QoS mechanism would you use to set the DSCP value specified of an outgoing packet?

A. dscp-cos-mapping

B. dscp-matching

C. dscp-marking

D. internal-priority-marking

Correct Answer: C

QUESTION 26sFlow uses which method to send data to a collector?

A. multicast

B. broadcast

C. TCP port 6343

D. UDP port 6343

Correct Answer: Dwww.Exa

mReal.c

om

www.Exa

mReal.c

om

www.Exa

mReal.c

om

ExamReal.Brocade.150-130.v20131025.113q

Documents

brocade mlxecorrect

brocade fcxcorrect answer

brocade products

brocade switches

brocade fastlroncxc

brocade fastiron device

brocade fastiron sxb

brocade fastlron sxb