"I install Lincoln Centro-Matic systems with confidence because I know they're going to prolong the life of my customer's critical machinery." Les Maness, Installation Foreman, Lincoln Distributor CENTRO-MATIC ® AUTOMATED LUBRICATION SYSTEMS CENTRO-MATIC ® AUTOMATED LUBRICATION SYSTEMS CENTRO-MATIC ® AUTOMATED LUBRICATION SYSTEMS
56
Embed
CENTRO-MATIC AUTOMATED LUBRICATION SYSTEMSmediaserver.voxtechnologies.com/FileCache/LINCOLN-SL-33-datasheet... · "I install Lincoln Centro-Matic systems with confidence because I
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
"I install Lincoln Centro-Matic systems with confidence because I know
they're going to prolong the life of my customer's critical machinery."
Les Maness, Installation Foreman,Lincoln Distributor
CENTRO-MATIC ®
AUTOMATED LUBRICATIONSYSTEMS
CENTRO-MATIC ®
AUTOMATED LUBRICATIONSYSTEMS
CENTRO-MATIC ®
AUTOMATED LUBRICATIONSYSTEMS
We’re the largest and mostsuccessful company in our fieldbecause we continually satisfy ourcustomers with the world’s bestlubrication and pumping systems.For almost 90 years, companieshave relied on our technical andquality leadership, our world-classmanufacturing and customerservice, and our vast network ofdistributors and support facilities.
Lincoln develops new productsand systems at research anddevelopment facilities in theU.S., Germany and India thatprovide global and regionalapplication solutions.
We have solutions for largeprocessing plants, automotivemanufacturing, pulp and papermills, and food and beveragefacilities. Virtually every industrialprofessional involved in operationsand maintenance can benefit fromLincoln systems.
On the road or in the field, Lincolnprotects heavy equipment used in mining,construction, agriculture and over-the-roadtrucking. The world’s leading manufacturersoffer our systems as standard equipmentor factory options.
Lincoln builds precision metalcomponents, state-of-the-artelectronic controls, and theindustry’s top-performing pumpsystems. Our quality systems inthe United States and Germanyare ISO 9001 registered.
With five technical supportcenters on three continents, anda network of systems houses anddistributors supported by regionalsales and service offices, ourcustomers can always draw onour worldwide resources.
To make sure your investmentresults in significant savings,Lincoln developed a uniqueprogram called BearingSaver®.You not only get a completeaudit of your facility, you alsoreceive an analysis of yourreturn on investment.
People, Capabilities and Systems toSave Money and Increase Productivity
Worldwide Support
Customer Service
Research &Development
BearingSaver®
Mobile Equipment
QualityManufacturing
IndustrialSolutions
Centro-Matic® Automated Lubrication SystemsTable of Contents
Air-OperatedActuated automatically bycompressed air at variouspre-determined intervals.An air-operated pumpdelivers lubricant to theinjectors. When all injectorshave cycled, the pump shutsoff automatically and ventslubricant pressure. Availablewith automatic, manual ormechanical controls.
ElectricUsed where compressed airis not available, or electricaloperation is preferred. Totallyenclosed motor supplies thepower requirements of thepumping mechanism. Timecontrol is adjustable toprovide predeterminedfrequency of lubrication.
ManualDesigned for smaller,individual machines, manualsystems provide a low-cost,efficient method of distribut-ing lubricant to the injectors.Cycling a complete bank ofinjectors takes only a fewseconds. In manually-operated systems, thelubricant pump is hand-operated and the machineoperator performs thelubrication intervals.
HydraulicA complete hydraulically-powered pumping unit forcentralized lubrication ofindividual machines. Usuallyinstalled on machinery suchas coal mining and earthmoving equipment whichutilize a hydraulic pressuresystem. The frequency ofthe lubrication cycle can beset manually or by mechani-cal or automatic controls.
Lincoln Centro-Matic® systems and components are made to match your application. Systems can service one machine,different zones on one machine or even several separate machines. Regardless of the application, the principle ofcentralized lubrication remains the same: a central pump station automatically delivers lubricant through a single supplyline to the injectors. Each injector serves only one lubrication point and may be accurately adjusted to deliver the preciseamount of grease or oil required. Centro-Matic systems give you multiple advantages over other designs.
SimplicitySystems are easy to understand, install and maintain. You realize savings right from the start because one lubricantsupply line means lower installation costs.
Powerful Pumping UnitCentro-Matic systems dispense either grease or oil in measured quantities, unaffected by normal temperature orviscosity changes. For large systems, Lincoln’s single-line design and powerful pumps mean injectors can be locatedlong distances from original refinery containers or bulk lubricant tanks.
External AdjustmentLubricant injectors are externally adjustable without special tools so each bearing can receive the correct amount oflubricant. No under- or over-lubrication at individual points.
Visual IndicatorsEach injector incorporates an indicator pin that gives visual confirmation the injector is operating correctly. Whennecessary, troubleshooting is the simple process of checking indicator pins.
Ease of ServiceWhen injectors finally need service, the job is quick and easy. No need to remove supply line connections or disturbadjacent injectors. Replacement can usually be done between lubrication cycles, so there’s almost no lubricant lossor downtime.
Parts and ServiceYou’re never far from a Lincoln authorized distributor. Qualified distributors offer design engineering, startup help andtraining for your personnel in the use and maintenance of Centro-Matic systems. They’ll back you up with parts andservice for years after the sale.
Basic Operating Principles of Centro-Matic® InjectorsEach Lincoln Centro-Matic injector can be manually adjusted to discharge the precise amount of lubricant eachbearing needs. Injectors are mounted singly at each bearing, or grouped in a manifold with feedlines supplyinglubricant to the bearings. In each case, injectors are supplied with lubricant under pump pressure through a singlesupply line. Two injector types are available: a top adjusting and a side adjusting. Both types can be used in thesame circuit; their selection is made on the basis of bearing lubricant requirements.
SL-V, SL-V XLStage 1—The discharge chamber is filled with lubricant from the previous cycle. Under pressure of incoming lubricant,lubricant is directed to both sides of the measuring piston through the slide valve. The port to the bearing is closed inthis position which prevents the measuring piston from moving. The indicator stem will be at its innermost position,having pulled away from the stop in the adjusting screw.
Stage 2—Pressure has built up and has moved the slide valve in position shown. This closes the flow passage to theupper side of the piston (larger diameter) while simultaneously opening the port to allow lubricant to flow out of theinjector to the bearing. Pressure from the supply line continues to apply pressure to the lower portion of the measuringpiston, which causes a pressure difference across the measuring piston thus allowing it to move upward.
Stage 3—Movement of the measuring piston is shown caused by the pressure on the lower side of the measuring pis-ton dispensing lubricant out to the bearing. The indicator stem will move up against the stop in the adjusting screwwhen all lubricant has been delivered to the bearing.
Stage 4—As the pressure in the supply line is vented down to 1,000 psi, the slide valve moves back to its rest position.Flow of lubricant to the bearing is closed and simultaneously allows lubricant to flow to the upper (larger diameter) ofthe piston. The displacement of fluid on the lower side of the measuring chamber is also allowed by the slide valve toflow to the upper side of the piston. The injector is recharged by the residual pressure in the supply line to the upperportion of the measuring chamber.
SL-1, -11, -41, -44Stage 1—The injector piston is in its normal, or rest position. The discharge chamber is filled with lubricant fromthe previous cycle. Under the pressure of incoming lubricant, the slide valve is about to open the passage leadingto the piston.
Stage 2—When the slide valve uncovers the passage, lubricant is admitted to the top of the piston, forcing thepiston down. The piston forces lubricant from the discharge chamber through the outlet port to the bearing.
Stage 3—As the piston completes its stroke, it pushes the slide valve past the passage, cutting off furtheradmission of lubricant to the passage. Piston and slide valve remain in this position until lubricant pressurein the supply line is vented (relieved) at the pump.
Stage 4—After pressure is relieved, the compressed spring moves the slide valve to the closed position. Thisopens the port from the measuring chamber and permits the lubricant to be transferred from the top of the pistonto the discharge chamber.
SL-32, -33, -42, -43Stage 1—Incoming lubricant, under pressure from thesupply line, moves the injector piston forward. The pistonforces a pre-charge of lubricant from the dischargechamber through the outlet check valve to the feed line.
Stage 2—When the system is vented (pressure relieved), thepiston returns to the rest position, transferring lubricant fromthe measuring chamber to the discharge chamber.
Applications—When it comes to eliminating costly,manual point-by-point lubrication, Centro-Matic systemshave proven to be the right solution for many industriesand applications. Examples include:
Notes:1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing — 1⁄8" O.D. as standard.Other outlet connectors for feed line optional.
2. Injectors with manifolds include two mounting clips and screws.3. Injectors have Nitrile packings (200°F max. / 93°C). Check packing compatibility with synthetic lubricants.4. Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./turn.
Specifications:
Series SL-33
• For single-line, high-pressure central lubrication system.• For dispensing petroleum-based lubricants with a viscosity up to NLGI No. 2 (refer to Design Guide).• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of Injectors SL-32, SL-V, SL-V XL, SL-1 and/or SL-11.• Individual injectors can be easily removed for inspection or replacement.• Available in stainless steel SAE 304, for application where environmental conditions are hazardous to carbon steel orin industries preferring stainless steel.
SeriesOutput Operating Pressure
Min. Max. Min. Max. Typical Vent
SL-33.001 cu. in..016 cc
.003 cu. in..049 cc
1200 psig83 bar
3500 psig241 bar
1500 psig103 bar
200 psig14 bar
Model
Number ofOutlets
Connections DimensionsCarbonSteel
StainlessSteel (304)
ManifoldInlet
InjectorOutlet
A Bin. mm in. mm
83309-1 83715-1 1
1⁄8" NPTF (F)1⁄8" O.D. Tube
11⁄8 29 15⁄8 41
83309-2 83715-2 2 17⁄8 48 23⁄8 60
83309-3 83715-3 3 25⁄8 67 31⁄8 79
83309-4 83715-4 4 33⁄8 86 37⁄8 98
83309-5 — 5 41⁄8 105 45⁄8 117
83309-6 83715-6 6 47⁄8 124 53⁄8 137
— 83715-7 7 55⁄8 143 61⁄8 156
83900 83900-9 1 1⁄8" NPTF (M) Single Injector/No Manifold
• For single-line, high-pressure central lubrication system.• For dispensing petroleum-based lubricants with a viscosity up to NLGI No.2 (refer to Design Guide).• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-33, SL-V, SL-V XL, SL-1 and/or SL-11.• Individual injectors can be easily removed for inspection or replacement.• Available in stainless steel SAE 304, for application where environmental conditions are hazardous to carbon steel orin industries preferring stainless steel.
Notes:1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing — 1⁄8" O.D. as standard.Other outlet connectors for feed line optional.
2. Injectors with manifolds include two mounting clips and screws.3. Injectors have Nitrile packings (200°F max. / 93°C). Check packing compatibility with synthetic lubricants.4. Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with five turns at .0014 cu. in./turn.
Specifications:
SeriesOutput Operating Pressure
Min. Max. Min. Max. Typical Vent
SL-32.001 cu. in..016 cc
.008 cu. in..131 cc
1200 psig83 bar
3500 psig241 bar
1500 psig103 bar
200 psig14 bar
Model
Number ofOutlets
Connections DimensionsCarbonSteel
StainlessSteel (304)
ManifoldInlet
InjectorOutlet
A Bin. mm in. mm
83336-1 83724-1 1
1⁄4" NPTF (F)1⁄8" O.D. Tube
11⁄4 32 13⁄4 44
83336-2 83724-2 2 2 51 21⁄2 63
83336-3 83724-3 3 23⁄4 70 31⁄4 83
83336-4 83724-4 4 31⁄2 89 4 102
83338 — 1 1⁄4" NPTF (M) Single Injector/No Manifold
• For single-line, high-pressure central lubrication system.• For dispensing lubricants compatible with polyurethane seals up to NLGI No. 2 (refer to Design Guide).• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-32, SL-33, SL-1, SL-V XL and/or SL-11.• Individual injectors can be easily removed for inspection or replacement.• Each SL-V injector includes a clear polycarbonate protective cap.
Specifications:
Notes:1. Injector manifolds have 13⁄32" (10.3 mm) dia. mounting holes for 3⁄8" bolt.2. Injectors have polyurethane seals Check compatibility with synthetic lubricants.3. Injector rated for 180°F (80°C) max. ambient temperature, depending on lubricant used.4. Injectors include fitting for filling feedlines via alternate outlet port.5. Output with adjustment screw hand-tightened is .015 cu. in. Maximum output is achieved with five turns at .014 cu. in./turn.
83/4"(222mm)
BA
11/4"(32mm)
1/8"NPTF
13/32" (10.3mm)MountingHoles
3/8" NPTF(both ends)
3/8"(19mm)
21/8"(54mm)
11/2"(38mm)
13/8"(35mm)
Series MaterialOutput Operating Pressure Connections
Min. Max. Min. Max. Typical Vent Manifold Inlet Injector Outlet
SL-V CarbonSteel
0.015 cu. in.0.25 cc
0.08 cu. in.1.31 cc
1850 psig128 bar
6000 psig415 bar
2500 psig170 bar
1000 psig70 bar
3⁄8" NPTF (F) 1⁄8" NPTF (F)
Model Type Number ofOutlets
Dimension A Dimension Bin. mm in. mm
85770-1 One Injector Manifold 1Single Mounting Hole
21⁄2 63
85770-2 Two Injector Manifold 2 3 76
85770-3 Three Injector Manifold 3 11/4 32 41⁄4 108
85770-4 Four Injector Manifold 4 2 63 51⁄2 140
85770-5 Five Injector Manifold 5 33⁄4 95 63⁄4 171
85770-6 Six Injector Manifold 6 5 127 8 203
85771 Replacement for manifold injectors
85772 Single injector/no manifold (3⁄8" NPTF(M) inlet)
• For single-line, high-pressure central lubrication system.• For dispensing lubricants compatible with polyurethane seals up to NLGI No. 2 (refer to Design Guide).• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-32, SL-33, SL-1, SL-V and/or SL-11.• Individual injectors can be easily removed for inspection or replacement.• Two SL-V XL injectors are required to replace one SL-11 injector.• Each SL-V XL injector includes a clear polycarbonate protective cap.
Specifications:
Notes:1. Injector manifolds have 13/32" (10.3 mm) dia.mounting holes for 3/8" bolt.
2. Injectors have polyurethane seals Checkcompatibility with synthetic lubricants.
3. Injector rated for 180°F (80°C) max. ambienttemperature, depending on lubricant used.
4. Injectors include fitting for filling feedlines viaalternate outlet port.
5. Output with adjustment screw hand-tightened is .015cu. in. Maximum output is achieved with 201⁄2 turns at.014 cu. in./turn.
113/16"(284mm)
BA
11/4"(32mm)
1/8"NPTF
13/32" (10.3mm)MountingHoles
3/8" NPTF(both ends)
3/4"(19mm)
21/8"(54mm)
11/2"(38mm)
13/8"(35mm)
Spectrum Adjustment Sleeves:
Series MaterialOutput Operating Pressure Connections
Min. Max. Min. Max. Typical Vent Manifold Inlet Injector Outlet
SL-V XL CarbonSteel
0.015 cu. in.0.25 cc
0.305 cu. in.5.00 cc
1850 psig128 bar
6000 psig413 bar
2500 psig172 bar
1000 psig69 bar
3⁄8" NPTF (F) 1⁄8" NPTF (F)
Model Type Number ofOutlets
Dimension A Dimension Bin. mm in. mm
85780-1 One Injector Manifold 1Single Mounting Hole
21⁄2 63
85780-2 Two Injector Manifold 2 3 76
85780-3 Three Injector Manifold 3 11/4 32 41⁄4 108
85780-4 Four Injector Manifold 4 21⁄2 63 51⁄2 140
85780-5 Five Injector Manifold 5 33⁄4 95 63⁄4 171
85780-6 Six Injector Manifold 6 5 127 8 203
85781 Replacement for manifold injectors
85782 Single injector/no manifold (3⁄8" NPTF(M) inlet)
* For complete assembly, you must order stainless steel manifold and corresponding quantity of Model #84776 Injectors separately.
Series SL-1
• For single-line, high-pressure central lubrication system.• For dispensing lubricants compatible with Viton® packings and viscosity up to NLGI No. 2 (refer to Design Guide).• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-32, SL-33, SL-V, SL-V XL and/or SL-11.• Individual injectors can be easily removed for inspection or replacement.• Available in stainless steel SAE 316, for application where environmental conditions are hazardous to carbon steel orin industries preferring stainless steel.
Specifications:
Notes:1. Injector manifolds have 13⁄32" (10.3mm) dia. mounting holes for 3⁄8" bolt.2. Injectors have Viton® packings. Check compatibility with synthetic lubricants.3. Injector rated for 350°F (176°C) max. ambient temperature, depending on lubricant used.4. Injectors include fitting for filling feedlines via alternate outlet port.5. Output with adjustment screw hand-tightened is .009 cu. in. Maximum output is achieved with eight turns at .009 cu. in./turn.
SeriesOutput Operating Pressure Connections
Min. Max. Min. Max. Typical Vent Manifold Inlet Injector Outlet
SL-1.008 cu. in..131 cc
.080 cu. in.1.31 cc
1850 psig127 bar
3500 psig241 bar
2500 psig172 bar
600 psig41 bar
3⁄8" NPTF (F) 1⁄8" NPTF (F)
Model
Number of Outlets
Dimensions
CarbonSteel
StainlessSteel (316)
A B A B
in mm in mm
81770-1 239351* One Injector Manifold 1Single Mounting Hole
21⁄2 63
81770-2 239352* Two Injector Manifold 2 3 76
81770-3 239353* Three Injector Manifold 3 11⁄4 32 41⁄4 108
81770-4 239354* Four Injector Manifold 4 21⁄2 63 51⁄2 140
81770-5 239355* Five Injector Manifold 5 33⁄4 95 63⁄4 171
81770-6 — 6 5 23 8 203
81713 — Single injector/no manifold, [ 3⁄8" NPTF (M) inlet]
81713A 84776* Injector Replacement for manifolded injectors
• For single-line, high-pressure central lubrication system.• For dispensing lubricants compatible with Viton® packings and viscosity up to NLGI No. 2 (refer to Design Guide).• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-32, SL-33, SL-V, SL-V XL and/or SL-1.• Available only as single unit with 1⁄2" NPTF Female inlet.
Specifications:
Notes:1. Injectors have Viton® packings. Check packing compatibility with synthetic lubricants.2. Injector rated for 350°F (176°C) max. ambient temperature.3. Injectors supplied with fitting for filling feed line via alternate outlet port.4. Output with adjustment screw hand-tightened is .05 cu. in. Maximum output is achieved with 111/2 turns at .040 cu. in./turn.
• For single-line central lubrication system.• For dispensing fluid or semi-fluid lubricants.• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-43, SL-41 and/or SL-44.• Individual injectors can be easily removed for inspection or replacement.• Carbon steel injectors with Nitrile or Viton® packings.• Injectors with Viton® packings are used for heat resistant applications or when lubricant to be dispensed requiresViton® packings for compatibility (indicated by black adjustment caps).
Notes:1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing – 1⁄8" O.D. as standard.
Other outlet connectors for feed line optional.2. Injectors with manifolds include two mounting clips and screws.3. Standard injectors have Nitrile packings (200°F/93°C max.); Heat Resistant injectors have Viton® packings (350°F/176°C max., depending on
lubricant used) and black adjusting cap. Check packing compatibility with synthetic lubricants.4. Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./turn.
Specifications:
SeriesOutput Operating Pressure
Min. Max. Min. Max. Typical Vent
SL-42.001 cu. in..016 cc
.003 cu. in..049 cc
750 psig52 bar
1000 psig69 bar
850 psig59 bar
150 psig10 bar
Model
Number of Outlets
Connections Dimensions
Standard Heat ResistantManifold/
Injector InletInjectorOutlet
A Bin. mm in. mm
83311-1 84428-1 1
1⁄8" NPTF (F)1⁄8" O.D. Tube
Connection
11⁄8 29 15⁄8 41
83311-2 84428-2 2 17⁄8 48 23⁄8 60
83311-3 84428-3 3 25⁄8 67 31⁄8 79
83311-4 84428-4 4 33⁄8 86 37⁄8 98
83311-5 84428-5 5 41⁄8 105 45⁄8 117
83311-6 84428-6 6 47⁄8 124 53⁄8 137
83311-10 84428-10 10 77⁄8 200 83⁄8 213
83311-15 84428-15 15 115⁄8 295 121⁄8 308
83535 — 1 1⁄8" NPTF (M) Single Injector/No Manifold
83313 84048 — — Replacement for Manifold Injectors
• For single-line central lubrication system.• For dispensing fluids or semi-fluid lubricants.• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-42, SL-41 and/or SL-44.• Individual injectors can be easily removed for inspection or replacement.• Carbon steel injectors with Nitrile or Viton® packings.• Injectors with Viton® packings are used for heat resistant applications or when lubricant to be dispensed requiresViton® packings for compatibility (indicated by black adjustment caps).
Notes:1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing – 1⁄8" O.D. as standard.
Other outlet connectors for feed line optional.2. Injectors with manifolds include two mounting clips and screws.3. Standard injectors have Nitrile packings (200°F/93°C max.)4. Heat Resistant injectors have Viton® packings (350°F/176°C max. depending on lubricant used) and Black Adjusting Cap.5. Check packing compatibility with synthetic lubricants.6. Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with five turns at .0014 cu. in./turn.
Specifications:
Series SL-43
SeriesOutput Operating Pressure
Min. Max. Min. Max. Typical Vent
SL-43.001 cu. in..016 cc
.008 cu. in..131 cc
750 psig52 bar
1000 psig69 bar
850 psig59 bar
150 psig10 bar
Model
Number of Outlets
Connections DimensionsCarbon Steel Manifold/
Injector InletInjectorOutlet
A B
Standard Heat Resistant in. mm in. mm
83661-1 84429-1 1
1⁄4" NPTF (F) 1⁄8" O.D. Tube
Connection
11⁄4 32 13⁄4 44
83661-2 84429-2 2 2 51 21⁄2 63
83661-3 84429-3 3 23⁄4 70 31⁄4 83
83661-4 84429-4 4 31⁄2 89 4 102
83660 84110 — — Replacement for Manifold Injectors
• SL-41 series injectors are designed for use in high temperature applications up to 350°F (176°C), depending on lubricant.
• Available installed only in manifolds with 3⁄8" NPT female inlet.
• Injectors feature a tamper-resistant adjustment screw which does not incorporate a visual indicator.
• May be combined in a circuit of injectors SL-42, SL-43 and SL-44.
Specifications:
Notes:1. Injector manifolds have 13⁄32" (10.3 mm) mounting holes for 3⁄8" bolt.2. Minimum output (.008 cu. in.) is achieved by hand tightening the adjustment screw, then backing out 9 turns. Maximum output (.08 cu. in.) is
achieved by hand tightening the adjustment screw, then backing out 16 turns.
SeriesOutput Operating Pressure
Min. Max. Min. Max. Typical Vent
SL-41.008 cu. in..131 cc
.080 cu. in.1.31 cc
750 psig52 bar
1000 psig69 bar
850 psig59 bar
150 psig10 bar
Model
Number of Outlets
Connections Dimensions
Carbon SteelManifold/
Injector InletInjectorOutlet
A B
in. mm in. mm
82294-1 1
3⁄8" NPTF (F) 1⁄8" NPTF (F)
Single Hole Mounting21⁄2 63
82294-2 2 3 76
82294-3 3 11⁄4 32 41⁄4 108
82294-4 4 21⁄2 63 51⁄2 140
82294-5 5 33⁄4 95 63⁄4 171
82292 Single Injector/No Manifold, [3⁄8" NPTF (M) Inlet]
82295 — — 1⁄8" NPTF (F) Replacement for Manifold Injectors
Notes:1. Injector manifolds have 13⁄32" mounting holes for 3⁄8" bolt.2. Injectors have Viton® packings. Check packing compatibility with synthetic lubricants.3. Injectors rated at 350°F (176°C) maximum ambient temperature, depending on lubricant used.4. Output with adjustment screw hand-tightened is .009 cu. in. Maximum output is achieved with eight turns at .009 cu. in./turn.
Series SL-44
• For single-line central lubrication system.• For dispensing fluid or semi-fluid lubricants.• Output is externally adjustable.• Indicator stem permits visual check of injector operation.• May be combined in a circuit of injectors SL-43, SL-41 and/or SL-42.• Individual injectors can be easily removed for inspection or replacement.• Carbon steel injectors with Viton® packings.
Specifications:Series
Output Operating PressureMin. Max. Min. Max. Typical Vent
With the same proven design as our U.S. standard injectors, the new metric versions of our popular small grease andoil injectors feature metric ports. Any surface that needs a wrench is metric. It’s more convenient for customers in mostof the world, and easier to maintain because there’s no need for a second set of wrenches or adapters.• Offered for international customers.• Metric ports connect with metric lines without adapters.• No need for a second set of tools.• Proven design used in the United States.• Models for both grease and oil.
Specifications:
SL-32 Series SL-33, 42 Series
3 1/16"78 mm
11/16"18 mm
3/4"19 mm
1/8" BSPP(F)ThreadBoth Ends
ModelOutlets
Connections Dimension A Dimension BOil
SL-42GreaseSL-33
GreaseSL-32
Inlet Outlet in. mm in. mm
85352-1 85351-1 1
1⁄8" BSPP(F)
6 mm
O.D. Tube
Connection
11⁄8 29 15⁄8 41
85352-2 85351-2 2 17⁄8 48 23⁄8 60
85352-3 85351-3 3 25⁄8 67 31⁄8 79
85352-4 85351-4 4 33⁄8 86 37⁄8 98
85352-5 85351-5 5 41⁄8 105 45⁄8 118
85352-6 85351-6 6 47⁄8 124 53⁄8 137
85353-1 1 11⁄4 32 13⁄4 44
85353-2 2 2 51 21⁄2 64
85353-3 3 23⁄4 70 31⁄4 83
85353-4 4 31⁄2 89 4 102
Injector Cover CapsInjector cover caps are designed to protect the injector from dirt, harmful liquidsand fumes.
Injector Connector TubePermits application of combined discharge of two or more Series SL-V, SL-1, SL-41or SL-44 injectors through one feed line. Used where bearing size is such thatmultiple injector output is required. Fittings 1⁄8" NPT male each end. Carbon steelconstruction.
Model For Injector Series Connections
81646 SL-V, SL-V XL OR SL1, SL41, SL44 1⁄8" NPTF Male
274824 SL-1 to SL-V connection 1⁄8" NPTF Male
Model For Injector Series Outlet Connections14988 1⁄8" NPTF Female84200 1⁄4" O.D. Tube14991 SL32, SL33, SL42, SL43 1⁄8" NPTF Male249281 4 mm Tube249282 6 mm Tube
Manual Grease Fitting AdapterAllows manual lubrication of the machine between normal system cycles.Carbon steel with Nitrile seals.
Model For Injector Series Outlet Connections84195 1⁄8" O.D. Tube84203
SL32, SL33, SL42, SL431⁄4" O.D. Tube
Injector Locking CapCarbon steel locking caps set injectors to fixed output.
Injector Outlet AdapterConverts individual injector lubricant outlet when standard 1⁄8" O.D. tube is notdesired. All adapters are carbon steel unless otherwise noted.
249281 4 mm Carbon Steel 249277 249271249282 6 mm Carbon Steel 249274 249273
* 3⁄16" (4.8 mm) maximum bulkhead thickness.
Assembly comes with one nut and one ferrule.
Closure Plugs for Injectors and ManifoldsFor use in plugging lubricant outlets of injectors and manifolds.
* For plugging outlet of series SL-32, SL-33, SL-42, SL-43 injectors.
Style 1
Style 2
Model For Injector Series Air Inlet Air Outlet
82272 SL-1, SL-44 1⁄8" NPTF(F) 1⁄8" NPTF(F)
Injector-Operated Air Valve
Metric Outlet AdaptersAdapts injector outlet to 4 or 6 mm tubing.
Feedline BrushUse to apply lubricant to chains and conveyors. 1⁄8" NPT(F) inlet, 1" long, 5⁄8" surfacearea diameter; aluminum body with nylon bristles.
Model 68874
Centro-Matic® Automated Lubrication SystemsP653S Electric Pump
18
P653S Pump Features
• Integrated pump supplies lubricant to a single line parallel lubrication system
• Pumps low- and high-viscosity greases including industry standard NLGI grade2 grease
• Easily interfaces with telematics technology in today’s heavy equipment
• Operating temperature range from -40°F to +158°F (-40°C to +70°C) VDCor 32°F to 122°F (0°C to 50°C) VAC*
• Neutral switch allows mobile equipment to remain idling with pump poweron but the timer is deactivated – allowing manual lubrication functionality.
Benefits
• Integration of major system components reduces labor and overall costs
• Simplifies lubrication system design
• Installation time is reduced due to the ”plug-and-play” pump design. Simplymount the pump, connect power and the supply lines and the system is readyfor operation.
• Neutral switch ensures lubrication only when the machine is operating –eliminating wasted grease.* Appropriate greases apply
Taking Lincoln’s Pump Performance and Dependability In A Totally New DirectionThe fully integrated P653S pump is an example of Lincoln’scommitment to providing innovative, cost-effective solutionsthrough industry-leading advances in technology. This next-generation, lower-cost pump package can be fitted withone of four reservoir sizes and easily adapts to many applications.
Reservoir Available inFour Sizes –4, 8, 15, and 20 LitersMeans Versatility inScheduling RefillingService Intervals
Available With orWithout Follower
(shown with follower)
Reservoir Refill Port
High-Volume Output
Vent Valve
ProgrammableController
120/220-AC or 24-DC Pump
INTERNAL COMPONENTS• Telematics SignalingCapabilities for LowLevel and SystemFault Detection
• Pressure Switch orTransducer
Centro-Matic® Automated Lubrication SystemsP653S Electric Pump
19
P653S Pump SpecificationsElectrical data DC Pumps AC PumpsIncoming voltage: 19 to 31 VDC 100 to 240 VACMaximum current: 10 amps 1.7 ampsFrequency: — 47 to 63 hzOperating temperature: -40°F to +158°F 32°F to 122°F
(-40°C to +70°C) (0°C to 50°C)Common Electrical Data for DC and AC PumpsMinimum pause time: 4 min.Maximum pause time: 59 hrs. 59 min.Pause time increments: 1 hr. or 1 min.Maximum pumping time: 10 min.Pump P653SOperating pressure with:Pressure switch: 3,500 psig (240 bar)Pressure transducer (adj.): 1,400 to 4,600 psig (96 to 317 bar)End of line pressure switchand transducer setting: 2,500 psig (172 bar)Number of outlets: 1Output: 1.5 in3/min (24.6 cm3/min)Pump ElementsPiston diameter: 7 mmNumber of pumping elements(connected together): 3
ModelNo. 24 VDC
120/230VAC
50/60 Hz
ReservoirSize (L)
FollowerPlate
InternalPressureSwitch
InternalPressureTransducer
Internal &End-of-LinePressureSwitch
Internal &End-of-LinePressureTransducer
80086 X 4 X80087 X 4 X80105 X 4 X80106 X 4 X80076 X 4 X X80077 X 4 X X80109 X 4 X X80110 X 4 X X80090 X 8 X80091 X 8 X80107 X 8 X80108 X 8 X80080 X 8 X X80081 X 8 X X80111 X 8 X X80112 X 8 X X80082 X 4 X80083 X 4 X80084 X 4 X80085 X 4 X80072 X 4 X X80073 X 4 X X80074 X 4 X X80075 X 4 X X80088 X 8 X80089 X 8 X80078 X 8 X X80079 X 8 X X
Available Pump ModelsNOTE: All models are designed for grease and include stirring paddle and low-level detection. Pumps include remote signaling cable,relief valve, electrical connectors and external pressure switch or transducer (as indicated for each model).
Reliable Operation in Harsh Environments• Wind turbines – especially offshore• Construction and mining• Commercial vehicles• Compact and medium-sized machinesand industrial applications
• Robust and easy system layout• Simple maintenance – easy to expand• SE1 suction elements for used lubricant• Suitable for quick separating lubricants• Increased profits and productivity• Improved operating times; less costlydowntime resulting from improperlubrication
• Lower costs for repairs and spare parts• Exactly matched metering reduces thecost of lubricant
• Improved safety by minimizing slipping• Hard-to-reach points are easily accessi-ble from a convenient point – whichalso improves safety
• Reliable supply of all connected lubrica-tion points. No points are “overlooked”
The Path to Cost ReductionA lack of lubrication can bring your machines and equipment to a screeching halt. Manual lubrication is often awkwardand expensive. Automated lubrication offers an efficient, rational and environmentally friendly solution.From a few lubrication points to a few thousand – Lincoln offers the complete range of lubrication equipment andsystems for professional lubrication of construction and mining equipment.Lincoln lubrication systems are based on the principle of grouping lubrication points together that can be serviced fromone supply point. Our modules build upon each other – enabling the system to grow in accordance with our customer‘srequirements. This enables us to offer a custom-tailored lubrication solution for individual needs.
Model No. Description Power Size Follower Transducer645-41064-3 P603S- 4XLF -3Z7-AC-2A7.16-S13-SE AC 4L X X645-41062-3 P603S- 8XLF -3Z7-AC-2A7.16-S13-SE AC 8L X X645-41110-2 P603S- 8XLBO-3Z7-AC-3A7.16-S12-SE AC 8L X645-41062-4 P603S- 8XLBO-3Z7-AC-3A7.16-S19-SE AC 8L X645-41062-3 P603S- 8XLF -3Z7-AC-2A7.16-S13-SE AC 8L X X645-41073-5 P603S-15XLF -3Z7-AC-2A7.16-S13-SE AC 15L X X645-41064-8 P603S- 4XLF1-3Z7-12-1A7.16-S01-SE 12 DC 4L X (Bayonett) X645-41064-7 P603S- 4XNBO-3Z7-12-2A7.16-S01-SE 12 DC 4L X645-41110-3 P603S- 8XLF1-3Z7-12-1A7.16-S01-SE 12 DC 8L X (Bayonett) X645-41062-9 P603S- 8XLF -3Z7-24-1A7.16-S01-SE 24 DC 8L X X645-41064-4 P603S- 4XLBO-3Z7-24-1A7.16-S17-SE 24 DC 4L X645-41064-6 P603S- 4XLF -3Z7-24-1A7.16-S13-SE 24 DC 4L X X645-41064-2 P603S- 4XNBO-3Z7-24-1A7.16-S01-SE 24 DC 4L X645-41062-8 P603S- 8XLBO-3Z7-24-2A7.16-S19-SE 24 DC 8L X645-41062-9 P603S- 8XLF -3Z7-24-1A7.16-S01-SE 24 DC 8L X X645-41062-7 P603S- 8XLF -3Z7-24-1A7.16-S03-SE 24 DC 8L X X645-41119-1 P603S-10XLF -3Z7-24-1A7.16-S13-SE 24 DC 10L X X
The pump with integrated controller is easy to install. The all-in-one design of thepump includes the programmable controller, a pressure switch/transducer and avent valve.
Simple System Design – Easy to Expand
The single-line system’s design and layout is uncomplicated, making it easy toinstall and operate. A single mainline reduces material and installation costs.
Easy to Service
It is quick and easy to exchange out an injector. The mainline or neighboring injec-tors do not have to be removed. The exchange can be performed between lubrica-tion cycles so that there is no wastage of lubricant or excessive costly downtime.
Additional Pressure Switch
An additional pressure switch at the end of larger systems can be used for addedpressure control to ensure correct lubrication
Special Features for Wind Turbine Applications – Also for Off-Shore Systems
Lincoln single-line systems completely vent during the pause interval. As a result,they are suitable for fast separating lubricants.
For rotating operation in wind turbines the reservoir is equipped with a followerplate and stirring paddle – which also facilitates the usage of fast separating lubri-cants. For stationary operation a stirring and fixed paddle is sufficient.
Model 83817 Economy Grease PumpManual pump has metal reservoir and spring-loaded follower. Indicator pin inpump base shows when 2500 psi system operating pressure has been achieved.
Model: 83817Output/Stroke: .100 cu. in. 1.6 ccReservoir Capacity: 1 lb. .45 kg
30 cu. in. 492 ccLube Outlet: 1⁄8" NPTF (F)Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 151⁄4" x 5 "x 55⁄8" 387 x 127 x 141 mmFilling Method: 14.6 oz. Grease Cartridge/Bulk Fill
Model: 1810Output/Stroke: .160 cu. in. 2.6 ccReservoir Capacity: 5 lb. 2.27 kg
150 cu. in. 2458.50 ccLube Outlet: 1⁄4" NPTF (F)Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 161⁄4" x 71⁄8 "x 73⁄4" 413 x 181 x 197 mmFilling Method: 81834 Filler Pump
Model 1810 Grease PumpTranslucent reservoir with spring-loaded follower. Indicator pin in pump baseshows when 2500 psi system operating pressure has been achieved. Refillthrough included fitting using Model 81834 filler pump or other manual pumpequipped with Model 645006 coupler.
Once you have determined your total lubricant requirements, your greatest line length and compensated for lineexpansion, you’re ready to determine the pump you need.
If your overall requirements are less than 2.4 cu. in. for oil or 2.15 cu. in. for grease, you can select a single strokepump. Should your requirements demand more capacity, a reciprocating pump will fill the need.
Your Lincoln representative will suggest the best pump for you based on your application. Look over thefollowing pages of pump selection options and feel free to ask questions.
Model 85434 Integrated Grease PumpRatio: 31:1Power: 120 VACTypical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 240 barMaximum Output: 1.4 in3 18.7 cm3
Reservoir Capacity: 4.5 lbs. 1.8 kgDimensions (LxWxH): 24.70" x 6.52"x 18.11" 627 x 166 x 460 mm
Model 85435 Integrated Grease PumpSame as Model 85434 except 240 VAC.
Model 85436 Integrated Grease PumpSame as Model 85434 except with a Ratio of 25:1 and Maximum Output of2.15 in3 (35.2 cm3).
Model 85442 Integrated Grease PumpRatio: 20:1Power: 120 VACTypical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 240 barMaximum Output: 0.45 in3 7.4 cm3
Reservoir Capacity: 1 lb. 0.450 kgDimensions (LxWxH): 5.25" x 7.24"x 12.02" 133 x 184 x 305 mm
Model 85444 Integrated Grease PumpRatio: 20:1Power: 120 VACTypical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 240 barMaximum Output: 0.45 in3 7.4 cm3
Reservoir Capacity: 4 lbs. 1.8 kgDimensions (LxWxH): 5.25" x 7.24"x 20.75" 133 x 184 x 527 mm
Model 85445 Integrated Grease PumpSame as Model 85444 except 240 VAC.
Centro-Matic® Integrated PumpsAll models are air-operated, positive displacement pumps delivering a maximum volume by means of a single stroke ofthe pump (volumes listed below). Solenoid air valves and adjustable solid-state time controls are integrated into thepump body. All pumps are designed to deliver grease to single-line injectors and include a special high-volume refillfitting. Acrylic reservoirs are available in several sizes. Integrated controls feature LED indicators for “Power On”, “PumpOn” and “Alarm,” along with a membrane-type, “Manual Lube” switch.
Timer and Controller SpecificationsOn Off Alarm OperatingTime Time Contacts Temperature10 sec 1/2 to 30 min 8 amps -10°F to 150°For 30 sec or 30 min to 30 hrs @ 250 VAC -23°C to 65°C
Note:Refer to System Controls section for detailed timer and solenoid operated air valvespecifications.
Timer Specifications
Cycle Time On Time Power Ambient OperatingMin Max Min Max Requirements Temp. Range
20 Sec. 24 Hr. 10 Sec. 1 Min. 24 Sec.120 VAC, 60 hz -10°F to +150°F110 VAC, 50 hz -23°C +65°C
Model 82886 PumpPump discharges lubricant on air-powered forward stroke and vents on spring-powered return stroke through built-in check/vent valve. Reservoir is translucent withspring-loaded follower. Includes filler fitting for refilling reservoir with Model 81834 orother manual pump equipped with Model 645006 coupler.
Model 83668Same as Model 82886 except includes larger reservoir.
Model 82653 Bare PumpPump uses air for forward and return stroke but dispenses lubricant on forwardstroke only. Return stroke vents lubricant pressure through included check/ventvalve. Translucent reservoir has spring-loaded follower. Refill through included fillerfitting using Model 81834 or other manual pump equipped with Model 645006coupler.
Model 83834 High Volume Bare PumpSame as Model 82653 except 25:1 ratio, 2.15 cu. in (35.2 cc) maximum output.
Model 82655 Pump with ControlsSame as Model 82653 except includes Model 84501 solid state timer and 350244four way electric solenoid valve.
Model 83800 High Volume Pump with ControlsSame as Model 83834 except includes Model 84501 solid state timer and 350244four way electric solenoid valve.
Note: Air consumption @ 100 psi is .15 CFM per stroke.
Model: 83167Lubricant/Air Ratio: 40:1Output/Min @ 100 PSIG Air: 12 cu. in. 197 ccReservoir Capacity: 12 lb. / 5.44 kg 360 cu. in. / 5900 ccAir Inlet: ¹⁄₈" NPTF (F)Lube Outlet: ³⁄₄" NPTF (F)Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 22¹⁄₂" x 9 "x 16¹⁄₄" 572 x 229 x 413 mmFilling Method: 81834 Filler PumpReservoir: Translucent AcrylicNotes: 1. Pump requires 3-way air valve. 2. Air consumption @ 100 psi is .15 CFM per cycle
Model 83167Includes transparent reservoir, spring-loaded follower, vent valve assembly andfiller fitting for refilling of reservoir with 81834 filler pump or other manual pumpequipped with Model 645006 coupler.
Model: 83599Lubricant/Air Ratio: 40:1Output/Min @ 100 PSIG Air: 12 cu. in. 197 ccReservoir Capacity: 12 lb. / 5.44 kg 360 cu. in. / 5900 ccAir Inlet: ¹⁄₄" NPTF (F)Lube Outlet: ³⁄₄" NPTF (F)Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 24³⁄₈" x 9 "x 18³⁄₁₆" 619 x 229 x 462 mmFilling Method: 81834 Filler PumpReservoir: AluminumNotes: 1. Pump requires 3-way air valve. 2. Air consumption @ 100 psi is .15 CFM per cycle
Model 83599Same as Model 83167 except includes base mounting kit and metal reservoirwith indicator rod for visual check of grease level. Reservoir includes spring-loaded follower.
Model: 1823Lubricant/Air Ratio: 50:1Output/Min @ 100 PSIG Air: 30 cu. in. 492 ccDrum Size: U.S. standard 120 lb. refinery drumAir Inlet: 3⁄8" NPTF (F)Lube Outlet: 3⁄4" NPTF (F)Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barComponents Pump & Vent Assembly 282288Included: Controller 85209
Pump Elevator 83447Controller Electrical Requirements: 120V, 60 Hz., 110 V, 50hzNotes: 1. Air consumption @ 100 psi is .42 CFM per cycle.2. Model 83371 follower plate is available as an optional accessory.
Model 282288Same specifications as Model 1823 but does not include elevator or controller.
Model: 1827Lubricant/Air Ratio: 75:1Output/Min @ 100 PSIG Air: 161 cu. in. 2638 ccDrum Size: U.S. standard 400 lb. refinery drumAir Inlet: 3⁄8" NPTF (F)Lube Outlet: 3⁄4" NPTF (F)Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barComponents Basic Pump 2004Included: Vent Valve 85215
Controller 85209Drum Cover 81675
Model 1828Same as Model 1827 except includes Model 2008 pump, 85218 vent valve andModel 84034 drum cover sized for U.S. standard 120 lb. refinery drum. Includes85209 controller.
Model 1829Same as Model 1827 except includes Model 2010 pump (50:1 ratio, 231 cu.in./min. (3785 cc) delivery at 100 psig air). Fits U.S. standard 400 lb. refinery drum.Includes 85209 controller and 85215 vent valve.
Model 1823Includes 21⁄2" air motor driven pump, vent valve assembly, pump elevator,connecting lubricant and air hoses, and control panel.
Model 1827 Heavy-Duty UnitConsists of PowerMaster pump, vent valve assembly with air and lubricantconnecting hoses, drum cover and control panel.
Model: 1812Output/Stroke: .160 cu. in. 2.6 ccReservoir Capacity: 4¹⁄₂ pint /130 cu. in. 2.13 liter/2130 ccLube Outlet: ¹⁄₄" NPTF (F)Typical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barDimensions (HxWxL): 16³⁄₄" x 7¹⁄₈"x 7³⁄₄" 425 x 181 x 197 mmNote: Check compatibility when using synthetic oils.
Manually–Operated Oil PumpModel 1812Pump has translucent reservoir with filler cap and strainer. Pump base has built-incheck/vent valve and an indicator pin to show when system pressure is achieved.
Model: 1849 *Output/Min: 18 cu. in. 295 ccReservoir Capacity: 12 lb. / 5.44 kg 360 cu. in. / 5900 ccLube Outlet: 1⁄4" NPTF (F)Electrical Specifications:
Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 253⁄8" x 13 "x 1913⁄16" 645 x 330 x 503 mmReservoir Fill Method: 81834 Filler Pump or Manual Pump and 645006 Coupler* See Model 85520 in Systems Control section for controller specifications.
Model 1835Same as Model 1849 except has 115 VAC, 60 Hz motor and controller.
Model 1849Fully automatic assembly including pump, 220/440 volt motor, translucent reservoirwith spring-loaded follower, 4000 psi (276 bar) safety unloader, adjustable pressureswitch and time control. Time control is adjustable for lubrication cycle frequency of5, 10, 15, 20, 30 or 60 minutes. Solid state time delay relay (35 sec. to 240 sec.)included for connection of audible or visual alarm to signal lubrication failure due toempty reservoir or broken supply line.
Model: 1833Output/Min: 18 cu. in. 295 ccReservoir Capacity: 12 lb. / 5.44 kg 360 cu. in. / 5900 ccLube Outlet: 1⁄4" NPTF (F)Electrical Specifications:
Typical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 341⁄4" x 111⁄2"x 213⁄4" 870 x 292 x 552 mmReservoir Fill Method: 81834 Filler Pump or Manual Pump with 645006 CouplerNotes:1. Controller has provision for remote manual lube button and remote lube failure alarm.2. Enclosure is designed to meet NEMA 3S and 12 specifications.
Model 1833Similar to Model 1849 except: 24 VDC pump motor and controller; metal reservoirwith visual level indicator rod; 2.5, 5, 10, 20, 40 and 80 minute cycle frequencyadjustment; 60 second fixed on time and alarm relay features. Incorporates pressureswitch factory set at 2500 psi (172 bar).
Model 85430 Integrated Fluid PumpRatio: 20:1Power: 120 VACTypical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barMaximum Output: 2.4 in3 39.3 cm3
Reservoir Capacity: 4.5 pints 2.1 litersDimensions (LxWxH): 24.70" x 6.52"x 18.11" 627 x 166 x 460 mm
Model 85431 Integrated Fluid PumpSame as Model 85430 except 240 VAC.
Model 85432 Integrated Fluid PumpSame as Model 85430 except without reservoir.
Model 85433 Integrated Fluid PumpSame as Model 85432 except 240 VAC.
Model 85438 Integrated Fluid PumpRatio: 20:1Power: 120 VACTypical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barMaximum Output: 0.45 in3 7.4 cm3
Reservoir Capacity: 1.25 pints 0.6 litersDimensions (LxWxH): 5.25" x 7.24"x 12.02" 133 x 184 x 305 mm
Model 85440 Integrated Fluid PumpRatio: 20:1Power: 120 VACTypical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barMaximum Output: 0.45 in3 7.4 cm3
Reservoir Capacity: 4.25 pints 2.0 litersDimensions (LxWxH): 5.25" x 7.24"x 20.75" 133 x 184 x 527 mm
Model 85441 Integrated Fluid PumpSame as Model 85440 except 240 VAC.
Centro-Matic® Integrated PumpsAll models are air-operated, positive displacement pumps delivering a maximum volume by means of a single stroke of thepump (volumes listed below). Solenoid air valves and adjustable solid-state time controls are integrated into the pumpbody. All pumps are designed to deliver fluid lubricants to single-line injectors and are filled via a spring-loaded filler capand internal filter. Acrylic reservoirs are available in several sizes. Pump Models 85432 and 85433 do not include a reser-voir, and are designed for remote or bulk-fill oil applications (80 psi/5.4 bar maximum head pressure). Integrated controlsfeature LED indicators for “Power On”, “Pump On” and “Alarm,” along with a membrane-type, “Manual Lube” switch.
Timer and Controller SpecificationsOn Off Alarm OperatingTime Time Contacts Temperature10 sec 1/2 to 30 min 8 amps -10°F to 150°For 30 sec or 30 min to 30 hrs @ 250 VAC -23°C to 65°C
Model 82885Pump discharges lubricant on air-powered forward stroke and vents on spring-powered return stroke through built-in check/vent valve. Translucent reservoir isrefilled through filler cap with strainer.
Model 83667Same as Model 82885 except includes larger reservoir.
Model 82570High-volume pump discharges lubricant on air-powered forward stroke and ventsthrough included check/vent valve on air-powered return stroke. Translucentreservoir is refilled through filler cap with strainer.
Model 82573Air-operated, single stroke oil pump and timer assembly. Same as Model 82570except includes Model 84501 solid state timer and 350244 four-way electricalsolenoid valve. Power requirements: 120 VAC, 60 Hz; 110 VAC, 50 Hz.
Model 82676Same as Model 82570 except for use with external oil supply through 1⁄2" NPT(F)oil inlet (maximum head pressure 80 psi (5.5 bar)).
** Air consumption @ 100 psi is .15 CFM per stroke.Check compatibility when using synthetic oils.
Model 82885
Model 83667
Model 82676
Note:Refer to System Controls section for detailed timer and solenoid-operated air valve specifications.
Timer Specifications for Model 82573 Only
Cycle Time On TimeMin Max Min Max
20 Sec. 24 Hr. 10 Sec. 1 Min. 24 Sec.
Metric Lubricant/ Max Reservoir Air Lube Lubricant Dimensions AirModel Equiv Air Output Capacity Inlet Outlet Oper. Press. HxWxL Valve
Typical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barDimensions (HxWxL): 253⁄8" x 13 "x 1913⁄16" 645 x 330 x 503 mmNote: See Model 85520, System Controls section for controller specifications.
Electric–Operated Oil PumpModel 1848Fully automatic assembly including pump, 220-/440-volt motor, translucentreservoir, 1200 psi (82 bar) safety unloader, adjustable pressure switch and timecontrol. Time control is adjustable for lubrication cycle frequency of 5, 10, 15, 20,30 or 60 minutes. Solid state time delay relay (35 sec. to 240 sec.) included forconnection of audible or visual alarm to signal lubrication failure due to emptyreservoir or broken supply line.
433 cu. in. 7100 ccAir Inlet: 1⁄8" NPTF (F)Lube Outlet: 3⁄4" NPTF (F)Typical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barDimensions (HxWxL): 231⁄4" x 9 "x 161⁄4" 591 x 229 x 413 mmAir Valve Required: 3-Way**** Air consumption @ 100 psi is .15 CFM per stroke.Note: Check compatibility when using synthetic oils.
Model 283167Includes 21⁄2" air motor driven pump, vent valve assembly, translucent reservoirwith filler cap and strainer and 1200 psi (82 bar) safety unloader.
Model: 1826Lubricant/Air Ratio: 24:1Output @ 75 Cycles/Min: 462 cu. in. 7571 ccDrum Size: U.S. standard 55-gal. refinery drum (removable head)Air Inlet: 3⁄8" NPTF (F)Lube Outlet: 3⁄4" NPTF (F)Typical System Min. 750 psig 52 barOperating Pressure: Max. 1000 psig 69 barController ElectricalRequirements: 120 V 60 Hz, 110V 50 HzNotes:1. See System Controls section for detailed controller specifications.2. See Industrial Pumping catalog for basic pump specification, including air consumption.
Model 1826Consists of Model 2002 PowerMaster pump, Model 85217 vent valve assembly,Model 81675 drum cover, Model 85209 controller, air and lubricant connectinghoses and 1200 psi (82 bar) safety unloader.
Model: 84050Lubricant/Air Ratio: 50:1Output/Min @ 100 PSIG Air: 30 cu. in. 492 ccReservoir Capacity: 60 lb. / 27 kg 1800 cu. in. / 29,500 ccAir Inlet: 3⁄8" NPTF (F)Lube Outlet: 3⁄4" NPTF (M) at HoseTypical System Min. 1200 psig 82 barOperating Pressure: Max. 3500 psig 241 barDimensions (HxWxL): 313⁄4" x 157⁄16 "x 159⁄16" 806 x 392 x 395 mmFilling Method: BulkReservoir: Steel
Notes: 1. Pump requires 3-way air valve. 2. Air consumption @ 100 psi is .42 CFM per cycle3. Optional Model 92597 follower available.
Model 84050A 50:1 ratio double acting air-operated pump for high-volume displacement. Suppliedwith a 60-pound capacity metal reservoir with removable cover for easy filling. Includesair-operated vent valve and 5' (1.5m) air and lubricant connecting hoses.
Model 85460Same as Model 84050 except includes installed visual low level and follower plate assembly.
Thick rubber seal to keepcontaminants out
Aircraft cable to strengthenconnection between
low-level and follower plate
Wiper on follower plateto better wipe off thegrease from the sides
Thick mounting ring withtwice as many mountingholes to resist loosening
Lincoln offers 60, 90 or 120 lb. reservoirs for our bucket pumps. Here are the features:• Rugged 14-gauge steel walls• Large 3⁄4" NPT inlet for fast filling• Wiper on follower plate that reduces lubricant waste• Special coupling for easy pump removal when servicing• Thick mounting ring that withstands severe vibration
These buckets work with hydraulic, air and electric pumps.
High-performance FlowMaster hydraulic pumps combine rotary-driven pumpmotors with reciprocating pump tubes and flexible control features that perform indesert heat and arctic cold. Integrated control manifold adjusts the amount oflubricant and operating pressure. The pump’s output is adjustable from 7 to 45cubic inches per minute.
Supply InletHydraulic Pressure, Max.: 3000 psig 200 barOperating InletHydraulic Pressure: 300 to 420 psig 20 to 32 barHydraulic Inlet Flow: Up to 7 gpm 28 l/minPump Ratio with Manifold: 9:1 at low inlet pressure (300 to 350 psi/20 to 25 bar)
and low inlet flow (below 2 gpm/7 lpm)pump ratio approaches 11:1 ratio at higher inlet pressure and flow
It seems too good to be true, but Lincoln’s new Electric FlowMaster Pump can serve all but the largest automatedlubrication applications. Now you can take advantage of the ease and economy of this efficient, versatile electricpump—no cost for air associated with running the pump and no hydraulic hoses to connect.The Electric FlowMaster Pump is a workhorse. Because you can adjust the speed of the pump’s motor, you can adjustthe pump’s output to precisely fit any application. Lincoln offers 12 different models.For manual lubrication, use the pump with a hose reel and a dispensing valve.
5.84(148)
2.95(75)
Speed ControlPotentiometer
1/4 NPTFPump Outletsboth sides
PowerWires
8.97(228)
6.82(173)
2.26(57)
Operating Temperature Range: -40° to +150°F -40° to +65°CPump Outlets: 1⁄4" NPTFMotor: 1⁄2" HP PEAK
Above models include follower plate and low-level detect * Includes high-level detect
* Kit consisting of pump, follower, bucket cover and hardware
Capacity Maximum Speed RangeModel lbs gal L Power Pressure Rating RPM85471 60 8 3085472 90 10 38 24 DC 5000 psi (345 bar) 36-36085473* 120 18 68
ModelGear Current Draw Output: in3/minRatio Amps Min Max
8547185472 5:1 2-15 2.8 25.285473
Pump and Bucket Models
274899 IP 67 ExplosionProof Rating
525-32083-1 IP 54 ExplosionProof Rating
Centro-Matic® Automated Lubrication SystemsFlowMaster® Electric Pumps
34
Now you can save the cost of air and plug in our new 120/230 VAC FlowMasterpump. Convenient and powerful, the 120/230 VAC FlowMaster pump allows you totap into your AC power source and pump grease from a 120 lb. or 400 lb. drum.Rely on it to drive your automated lubrication systems such as Centro-Matic®,Mod Lube®, Quicklub® and Two-line.
Operating Temperature Range: -40° to +150°F (-40° to +65°C)Operating Voltage: 120/230 VAC (60 Hz only)Pump Outlets: 1⁄4" NPTFMotor: 1⁄2 HP
Operating Temperature -20° to +140°F (-29° to +60°C)Operating Voltage 24 VDC (18 min., 30 max.)Motor 1/3 HP (0.25 kw)Max. Current Draw 15 AMPSMax. Output 18.0 in3/min (295 (cm3/min)Max. Output Pressure 6,000 psi (413.8 bar)Pump Weight 35 lbs. kg (15.9)Hose Reel Capacity 3/8" High Pressure Hose, 50 ft. (15 m)Mounts on 35#/5-gallon refinery container
Description Model No.10,000 psi Gauge 27487235#/5-gal. 274934Container Mount
Model Description274873 Bare, high-pressure pump274874 Bare pump with integrated pressure switch and manifold
Accessories
120/230 VAC FlowMaster®
Reel-N-Flow Pump and Reel Kit
Capacity Maximum Speed RangeModel lbs gal L Power Pressure Rating RPM85588 400 55 208 120-230 AC 5000 psi (345 bar) 36085589 120 18 68
ModelGear Current Draw: Amps Output: in3/minRatio @120 V @230 V Min Max
85588 5:1 1-4.6 .5-2.4 24.5 24.585589
Pump Only Models
Pump Models
Model Description Bare Lid Follower Reel Connect- Control Vlv.Pump ing Hose & Swivel
274886 274874 with bucket lid 274874 274878 274888and follower274886 with hose reel, 3050,274887 50' hose,control valve, 274874 274878 274888 94553H 75084
81729swivel & 7'connecting hose
Kit Models
Centro-Matic® Automated Lubrication SystemsFlowMaster® Electric Pumps
35
The high-performance FlowMaster product line is a new generation of pump tech-nology. Compact and versatile, its unique rotary drive and modular gear set let youadjust the pump to exactly fit your application.
• Wires directly to existing AC service• Reduces installation costs – no need to tap into hydraulic circuitsor pipe in compressed air
• Integrates easily to many styles of lubrication systems
Markets include:
• Heavy industry • General Industry– Mining – Food/beverage– Steel – Automotive– Paper – Packaging
– And others
Pump Model 85850 85851Pump/Container Size 120 lb. 400 lb.Pump Output 400 cm3/min. (24.5 in3/min.Operating Temperature -40° to 65°C (-40° to 150°F)Motor Max. Temperature Up to 105°C (220°F)Operating Voltage 380/420 Volts 3 PhaseMotor Power 1/2 HpPump Outlet 1/4" NPTF
Model: 84944Nominal Lubricant/Hydraulic Pressure Ratio: 16:1Output/Min @ 30 Cycles/Min: 11 cu. in. 180 ccReservoir Capacity: 60 lb. / 27 kg 1800 cu. in. / 29,500 ccHydraulic Inlet/Outlet: 1⁄4" NPTF (M)Lube Outlet: 3⁄4" NPTF (M)Important Note:1. Pumps require a timed electrical signal to operate. Use Model 244270 Cycle Timer. See System
Controls section for specifications.2. Included hydraulic solenoids require 24 VDC.
Model 84961Basic pump only for Model 84944. Includes pump and hydraulic control. Does notinclude reservoir or vent valve.
Model 84960Hydraulic pump for use with U.S. standard 120 lb. refinery drum. Systemcomponents (pump, vent assembly, drum cover and follower plate) must beordered separately.
Model 84962Hydraulic pump for custom lubricant container installations. Pump length is sizedfor U.S. standard 400 lb. refinery drum depth.
Model 84944Hydraulic-operated pump with 60 lb. metal reservoir and vent valve.
Hydraulic Power Supply RequirementsHydraulic Inlet Flow Rate Fluid Max.
Ambient OperatingPressure@ 30 Cycles/Min. Inlet
Temperature RangeFiltration
psig / bar Temperature RequirementMin Max GPM ltrs/min Min Max
Hydraulic Pressure Ratio @ 30 Cycles/Min Outlet Length Diameter
84960 — —16:1 11 in3 / 180 cm3 1⁄4" NPTF(F)
849623315⁄16" 1"862 mm 25.4 mm
Model 84944
Model 84960
Model 84962
Centro-Matic® Automated Lubrication SystemsAirless Spray System
37
No air required—three words describe why Lincoln’s innovative new Airless SpraySystem is the only system of its kind on the market. But it takes many more wordsto list all the benefits the latest in Lincoln’s long line of technological advances hasto offer. Because no air is required, the Airless Spray System means that mining,concrete, steel and other heavy industries can look forward to dependable,high-pressure lubricant spraying that’s low-maintenance and cost-effective.
Airless Spray High-Pressure System
Lincoln offers many pump options for supplying lubricant to the lube system.Air-operated pumps are preferred when possible due to their versatility and widerange of selection. Hydraulic and electric pumps are also available. The pumpmust be capable of pumping the lubricant to a minimum of 3500 psi at theairless spray valve.
Pumps
Model Operating Voltage Solenoid Valve Initial Current Heater Current85418 115 VAC .18 Amps 1.80 Amps
Model DescriptionDual filter panel with operator valve to select one of the two filters. The other filter
85419 is isolated from the system pressure for uninterrupted service and easy elementreplacement
84111 High-pressure, single in-line filter (recommended)84004 Single in-line filter
85418 Airless Spray Valve
Filters
Std Spray Std Tip with Roto-Clean Roto-Clean TipModel Descrip. Tip Swivel Tip with Swivel*252790 Retaining Nut Required Not Required Not Required Not Required252792 Jet Stabilizer Optional Optional Optional Optional85423-xxxxx ** Std. Spray Tip Required Required Not Required Not Required271579 Swivel Assy Optional Required Optional Required252831 Body Not Required Not Required Required Required85427-xxxxx ** Roto-Clean Tip Not Required Not Required Required Required
Spray Tips
* Discard tip retaining nut and protective cover, supplied with swivel assembly, when installing the roto-clean tip ona swivel assembly.** See chart below for spray tip models
Centro-Matic® Automated Lubrication SystemsAirless Spray System
38
To be furnished by installerHigh Pressure Grease Supply Line
Model Description
254120 For single and dual Airless systems. Operates system by setting the time betweenlubrication events. Includes manual lube button and system alarm.
256228 For single Airless system with external initiate contacts with manual lube buttonand system alarm
254815 For dual Airless system with external initiate contacts with manual lube buttonand system alarm
Controllers
Model Description
256241 25' wiring harness connects the controller to each spray valve.One wiring assembly is required for each spray valve.
Model Description
272285 For multiple machine/single pump applications. See design guide (form #403172)for details.
Follower PlatesRecommended when pumping lubricants that do not readily seek their own level.
Model Use with Pump Models Container Size83370 1827, 1829 Standard U.S. 400 lb. refinery drum83371 1823, 282288, 84960 Standard U.S. 120 lb. refinery drum92544 1828, 1830 Standard U.S. 120 lb. refinery drum92597 84050, 84944 Lincoln 60 lb. container252725 85483 Lincoln 35 lb. unit85489 85481 Lincoln 60 lb. unit
Pressure KitsSeal reservoirs for automatic filling.
Model Use with Pump Models83368 8288583637 82570, 82573
Automatic Filling System Pressure RegulatorPressurized systems automatically keep up to eight, single stroke oil pump reservoirsfull at all times. Use with reservoir seal kits below. Fill pump not included.
Fill Pump Fill System RequirementsLubricant VentRequirements Reservoir
Model Max. * Max.Max. Length
Pressure Inlet/Outlet Outletpsig / bar Ratio 5⁄8" Tube 3⁄8" Tube psig / bar
In-Line Lubricant FiltersFilters mount in pump outlet before vent valve on reciprocating pump systems.Removes solid contaminants before delivering lubricants to the supply line.
* In-line filter with Viton® seal.Model 84004, 84523
Max 31 cc Coupler 263⁄4 14 91 pint/ 30 pints 5' 80599 679 356 229
1254 Oil 7 strokes14.2 L 1.5 m
Non-Drip473 cc Nozzle
Manual Filling PumpsDesigned to provide a fast, clean method of filling Centro-Matic pumps with aself-contained reservoir without the risk of lubricant contamination.
Metal Reservoirs: Rectangular reservoirs forgravity feed oil pumpsStandard ³⁄₈" NPTF outlet furnished for gravity-fed pumps. Features spring loadedcap with strainer, sight gauge and Buna-N O-rings. Model 84376 Sight Gauge Kitavailable for use with synthetic oil.
Cylindrical ReservoirFour-gallon steel tank-type reservoir consisting of Model 82700 tank and Model82612 mounting brackets. Incorporates large filler opening with screw cap.
Ambient Protection Power Supply Current Switching OutputsTemp. Range Operating Range less load Max. Current High Level Low Level
-13°F to 158°F NO contact NO contact
-25°C to 70°C IP65 20 - 30 VDC 60 mA 200 mA (closes (openswhen full) when low)
Model Description270782 Ultrasonic sensor270781 Ultrasonic sensor socket (required)
Ultrasonic SensorUltrasonic High/Low Sensor to make it easier to know when the 60 lb. Centro-Matic®
automated lubrication system reservoir is getting low on lubricant and when it’s refilledto capacity. Sensor detects the position of the follower plate with ultrasonic waves toreport the lubricant level. The sensor is factory programmed for a 60 lb. reservoir. Itstwo outputs drive external signaling devices or connect with a customer’s PLC. Threestandard LEDs offer visual indication of the sensor’s sensor status and reservoir level.
Model 84501 Program Timer—Solid StateDesigned to control the lubrication cycle frequency of air-operated single-strokepumps. Timer turns pump on/off at programmed intervals via a 3-way or 4-wayair solenoid valve (not included) installed in the air line to pump.
Off Time On TimePower Approvals Switch(Cycle Time) (Pumping Time)
Requirements CapacityMin Max Min Max
20 Sec. 24 Hrs. 10 Sec. 1 Min. 120/230 VAC UL, CSA 120 VAC, 5 Amps24 Sec. 50/60 Hz 230 VAC, 1.5 Amps
Model 84511 Economy Timer forSingle Stroke PumpsUses a timing motor, cam and switch to turn pump off and on. NEMA 1enclosure, UL and CSA listed. Switch capacity 10 amps non-inductive.
Off Time On TimePower Approvals Switch(Cycle Time) (Pumping Time)
Requirements CapacityMin Max Min Max5 Min. 1 Hr. 30 Sec. 90 Sec. 120 VAC, 60 Hz UL, CSA 10 Amps
Built-In Program Options Enclosure Ambient OperatingTemperature Range
3 Hr. Program Prelube Rating Dimensions-in./mm Minimum MaximumMemory Function Height Width Depth
Yes No Yes No NEMA #1 8¹⁄₄ 6¹³⁄₁₆ 4¹⁵⁄₁₆ 0°F 130°F210 173 125 -18°C 54°C
Enclosure
RatingDimensions - in. / mm
Height Width Depth
NEMA 1 5 / 127 3¹⁄₄ / 82.5 3¹⁄₂ / 89
Note: Off-time selectable in 5 minute intervals.
Selecting the right controls for your automated lubrication system is one of the last steps in the design process.Several different models may be chosen to control power-operated pumps, depending on the degree of automationand monitoring required. Your Lincoln representative will assist you in specifying the correct model.
Options range from simple timers to fully-automated system controllers and monitors. Basic timers allow you to set theinterval between lubrication cycles. More sophisticated monitors control the frequency of lubrication, oversee systemperformance and can sense lubricant flow to each bearing while showing system status and alarms on a LCD displaypanel. Monitors may be interfaced with machine control systems to protect your equipment from harm.
You may customize your installation with air and lubricant filters to prolong system life, pressure gauges for monitoring,shut-off valves to ease future maintenance and even automated filling systems to utilize bulk lubricant storage.
All of these possibilities, and more, have made Lincoln Automated Lubrication Systems the choice of industry for over80 years.
Note:Refer to Technical Manual for a full explanation of available program options.
Model 84015 Timer—12-24V DCSolid-state microprocessor-based controller for automated lubrication systems onmobile equipment or where AC power is not available. Rugged construction withliquid- and dust-tight enclosure. Includes manual push-button for remote initiationof a lube cycle.
Off Time**Fixed On Time Power Switch(Cycle Time)(Pumping Time) Requirements Capacity
* Less load. ** Available selections are 2.5, 5, 10, 20, 40 or 80 minutes.
Model 85535 System Controller—24V DCSame as Model 85520 except is a 24-volt DC.
Model 85525 Programmable ControllerSame as Model 85520 except includes pressure switch and mounting brackets.
Model 85520 Programmable ControllerMicroprocessor-controlled, 120 volt AC unit is fully programmable. Controller hasa wider off-time range than timers and a memory switch to turn pre-lube option onor off.
Off Time On Time (Pumping/Power
Switch Capacity(Cycle Time) Alarm Time)
RequirementsInductive Load at 120VAC
Min. Max. Min. Max. Load Relay Alarm Relay
30 Sec. 30 Hours 30 300 120 VAC 2 2Sec. Sec. 50/60 Hz Amps Amps
Power Requirements External Ambient PanelCurrent Alarm Temperature Dimensions
Voltage (less load) Load Range in. / mmCapacity Height Width
120 VAC, 60 Hz47 VA 360 VA
32° to 122°F 12 18¹⁄₄110 VAC, 50 Hz 0° to +50°C 305 464
Model 85209 Panel MountedPneumatic Control SystemPanel mounted units control lubrication frequency and monitor supply line pressure.Includes Model 85530 Controller (specifications above), Model 69630 PressureSwitch and solenoid-operated air valve.
Lube Cycle PumpingTimer Counter Max. TimeMode Mode Count Before ConnectionsOff Time Off Counts Rate Alarm
Model 85500 System Sentry IIThe ultimate automated lubrication system controller/monitor now features greatermonitoring accuracy with less sensitivity to lubricant flow rates, feed line length, orbearing back pressure. System Sentry II is always on the job, making sure that everylube point is lubricated when it’s supposed to be.
• Solid-state controller with LCD status display and 16-button keypad forsystem programming
• Controls up to two pumps with as many as two lube zones per pump• Fully programmable monitoring and alarm functions• Be set up to monitor every lube point for lubricant flow during each lubricationevent
• Easy to understand prompts reported by simple English language messages inreal time
Some functions require optional accessories. Use a maximum of 48 sensors andthree accessory Sensor Boards (order separately—16 sensors per board) to monitorlube points.
Lube CycleMax. Pumping Time
Timer Mode Counter Mode Count Before AlarmOff-Time Off-Counts NetMin. Max. Min. Max. Rate* Min. Max. Wt.
Model 247333 Pressure TransducerPressure Transducer signals actual system pressure via LCD display of SystemSentry II. Comes with 72 inch (1.8m) shielded 24-gauge connecting wire.Maximum length of wire between transducer and monitor is 30 (9.1m) feet.
Range Accuracy Proof Pressure Ambient Voltage EnclosureConnection Temp. Input Output Offset
NEMA 4X0 to
±1%7500 psig ¹⁄₄" NPT -20° to 180° F 10 to 1-6 1 Rating
4000 psi 517 bar Male Thread -29° to 82°C 30 VDC VDC 300 Series276 bar VDC Stainless
Steel
Lubricant Min. Flow Inlet/ Min. IntervalModel Description Construction
Temp. Range Per EventBetween Lube
Outlet Flow Event
250400Straight SensorAssembly Brass Sensor
25049090° Sensor & Plated Steel
32° to 145° FAssemblyCheck Body
0° to 63°C1/8" 30 Seconds
250500Straight Sensor 316Assembly Stainless Steel
25059090° Sensor Sensor &Assembly Check Body
Model 250365 Sensor BoardPlug-in accessory board used with Model 85500 that allows the attachment of upto 16 lube flow sensors. (Model 85500 comes without boards installed and canhold up to a total of three.)
Sensor AssembliesSensor assemblies consist of a check body and lube sensor with attached 30'cable. Cables are epoxy potted into the sensors for a watertight seal. Sensorshave a 3⁄8" pipe thread for conduit connection and a Viton® O-ring seal. Checkbodies terminate in a 1⁄8" NPTF male thread for attachment to a bearing or otherlubricant inlet. Maximum working pressure 6,000 psi (414 bar). Maximum wirerun from sensor to monitor is 500 feet (152m).
.004 cu.in./.066 cc@ 32°F / 0° C to125°F / 52°C
.008 in3 / .131cc@ 126ºF / 53ºC to145ºF / 63ºC
Model 243100 Sensor Wire100 foot (30.5 meters) coil of two conductor 22-gauge wire for connecting sensorsto monitor. Maximum length of wire between sensor and monitor is 500 feet(152 meters).
Lube Controller, Required1 Pump, 1 per Zone Required 1 — — —Up to 3 Zones (3Max.)
Lube Controller, Required 22 Pumps, 1 Zone No (1 per Pump) — — —Per Pump
Lube Controller, Required Required 22 Pumps, Up to 2 1 per Zone (1 per Pump) — — —Zones Per Pump (4Max.)
Lube Point Required Required RequiredMonitoring — — 1per each 1 per Quantity≤ 48 Points 16 Sensors Lube Point As Needed
Note 1: Controller may be operated without a pressure switch or pressure transducer but will not beable to monitor and alarm for lube system pressure failures.
Note 2: Sensors include 30' (9.1m) cable pigtail. Select brass/plated steel or stainless steel sensors instraight or 90° configuration as required.
Note 3: Maximum distance between monitor and sensor is 500' (152 meters).
Use This Guide to Select Accessories forModel 85500 System Sentry II
Model 249605 Sealed Cycle TimerSealed timer attaches to Lincoln 16:1 Hydraulic Pumps and generates timed pulsesignal to control pump reciprocating cycle rate.
Power Cycle Rate/MinuteRequirement Min. Max.
24 VDC 6 60
Electric Solenoid-Operated Air Valves
Electrical CharacteristicsPower Inrush Holding Air Ambient Cv Max. ConduitModel Type
Requirements Current Current Inlet/ Temperature Factor Pressure ConnectionAmps Amps Outlet Range psi / bar
110 VAC, 50 Hz350244 120 VAC, 60 Hz .11 .07
4-Way 8.4 VA 0° to 120°F 1.2220 VAC, 50 Hz -18° to 49°C
Model 83354 Signal MonitorDesigned to provide visual and audible indication of system operation and failure.Utilizes signal from system controller. Includes Model 69606 Alarm Horn mountedon enclosure door.
PowerIndicator Lamps
AudibleDimensions - in / mm
Requirement Power Lube System AlarmOn System On Failure Height Width Depth
115 VAC69606 Horn 10 8 650/60 Hz Green Amber Red(included) 254 203 15235 VA
Model 69630 Pressure SwitchSenses supply line pressure rise/fall to signal system operation to controller orsystem alarm.
Switch Capacity Adjustable Range - psig / bar ConnectionsType Decreasing Increasing
Lube ElectricalAC DCMin. Max. Min. Max.
10 Amps at 15Amps@6VDC ²⁷⁄₃₂" holeSingle 125, 250 or 5Amps@24VDC 250 2775 280 3000
¹⁄₄" NPT(F)for ¹⁄₂"
Contact480 VDC
.03 Amps@ 17 191 19 207 conduit250 VDC connector
Note: Lamps and horn are U.L. listed.
Note: Pressure switch has a NEMA 3 housing and UL listed switching elements.
Centro-Matic® Automated Lubrication SystemsNumerical Index
49
Viton® and Teflon® are registered trademarks of DuPont Performance Elastomers
A Complete Line of Lubrication Solutionsand Industrial Pumping Products
Our automated systems dispense measuredamounts of lubricant at predetermined intervals.Systems include Helios® and Duo-Matic® two-linesystems, Centro-Matic®, Modular Lube® andQuicklub® as well as ORSCO® precision oil lubrica-tion. With our BearingSaver®program, we find thebest automated solution for you from our widerange of systems for grease, fluid grease and oil.
Lincoln has developedspecialized pumps andpumping stations tohandle the difficult job oftransferring thick fluids. Fromthe industry-best PileDriver III®
and PowerMaster III® pumpsand air motors to specialtypumps, controls and mountingaccessories, Lincoln is thepreferred pumping systemfor many tough applications.
Sometimes a simpleapproach is the bestsolution. Our wide rangeof products includes smaller,self-contained automatedlubricators and generallubrication equipment.
Automated Lubrication
Industrial Pumping
General Lubrication
Whatever the service—evaluating your lubrication methods, installing a custom-engineered system, or supplying top-quality manual lubrication products—your Lincoln distributor makes certain you always get the very best value.
Systems House Distributors
Our systems house distributors offer the highest level of expertise available in theindustry. They can custom design a system with the exact combination of Lincoln components you need. Then, they install the system in your plant with their knowledgeable technicians or work with your personnel to make sure the job is done correctly. Each distributor stocks a full inventory of pumps, metering devices, controllers, monitors and accessories. Each continues to meet our stringent requirements for product, systems and service knowledge. From Los Angeles to London, Boston to Bangkok, Lincoln’s top-of-the-industry systems house distributors will be there when and where you need them.
For the nearest
authorized Lincoln
sales and service
representative, call:
Lincoln's global distribution networkis the best in the industry.Lincoln's global distribution network is the best in the industry.