CDS_Eclipse E4_Catalogue

ECLIPSE E4

Wood - Max 120 kg per panel

ECLIPSE

The window as a new piece of furniture: no longeronly a tool of protection and closing environments, buta new way of conceiving space.

With ECLIPSE the window changes shape, change its appearance, it changes lives.

ECLIPSE allows to create folding door andwindow in wood, clad (wood-aluminum) or wood-bronzeand aluminum, making it an added value for each house.

ECLIPSE SYSTEMSSystem for folding doors and windows

The window can be flat, rounded or angular; in the lattercase without need for a column in the middle.

Versatile, easy to install and assemble, the ECLIPSEwindow gives the house an higher gear.

ECLIPSE becomes the new philosophy of life: the varioustypes satisfy all requirements.

The six lines of the ECLIPSE system allow to realize windows of high value for every situation, both internal andexternal, alwasy following the same philosophy: the view becomes panoramic.

ECLIPSE allows to create folding doors and windows thatcan reach 16 meters in width and 3 or 4 meters in height,depending on the type of system selected.

ECLIPSE System provides the window opening is toboth outward or inward, to resolve all need of space.

In wood, wood-aluminum, or wood-bronze.Any combination is possible: ECLIPSE system is the mostversatile system.

FEATURES

Completeness of the systemProvides all the necessary elements for the construction of thewindow: the upper track, the lower track or the sill, hinges, carrier, dropbolt, seals and lock with cylinder.ECLIPSE, never been easier.


ECLIPSE, never been easier.

Easy construction of the frame and the panelsPanels all the same, smooth, without rebate. Frame and the bottom frame of easy construction.The accessories are all applied in support. The only milled from buildon the panels are for the housing upper and lower dropbolts and seals.


Adjusting to window installedECLIPSE allows to adjust the window when the window is installed, without remove thepanels. The vertical adjustment occurs when the window is mounted, acting on the lower carriers; while the lateral adjustmente occurs on the hinge side of the frame.

Vertical adjustment Lateral adjustment

LINEAR WINDOWS

Can make window wide up to 16 meters, with a 16 total panels, forup to 8 panels for side, opening outward or inward.

Any combination is possible, such as: 4 left panels, or 5 right panels,8 left panels, or 3 left panel + 8 right panels, or 1 left panel + 5 right panels, etc.ECLIPSE, never been easier.

CURVED WINDOWS

Can make curved windows,opening outward or inward.The only important element to be considerer is the measurementof the radius, that should not be less than 4 meters.The upper and the lower tracks are curved to measure.Although it is curved, the window does not change: the panels


Although it is curved, the window does not change: the panelsare all square, smooth, withouth rebated, and all the same, justas linear window.ECLIPSE, never been easier.

WINDOWS AT AN ANGLE

Can create two windows to close two side of a room, withoutthe need of a column in the corner. The windows are all the same, with the only except that the last leaf of each side will present the rebate to facilitate the closing of the window.


SHUTTER OR INTERNAL PARTITIONS

The ECLIPSE System allows to create even shutters, or internal partitions. These shutters can be installed even in the presence of a window existing sliding doors, thus providing thedarkening function.ECLIPSE, never been easier.

All ECLIPSE System are composed of identical elements, which differ only dependingon the flow rates of the different systems.

At the bottom ECLIPSE Systems can provide for the application of a track as exemplifiedin the figures below.

The bottom track can be completely embedded in the floor, resulting in a window with a flat base and absolutely not cumbersome.Ideal for close porches, conservatories or other environmentsthat do not require specific performance of resistance to weathering.

Bottom track encased in a wooden bottom frame

ECLIPSE SYSTEMSFeatures - The lower tracks

Bottom track into the floor

Bottom track encased in a wooden bottom frameIn case of a window opening to the outside, the bottomtrack can be encased into a wooden bottom frame,resulting in a window with a bottom internal rebate that allows excellent performance of resistance to agents atmospheric.

In case of window opening to the inside, the bottomtrack can be encased in a woodden bottom frame, resulting in a window with a external bottom rebate thatallows excellent performance of resistance to agents atmospheric.

In a particular situation such as a garae, where there is not require performance of resistance to weathering, the bottom track can be encased directly in the floorwith a ramp.

Bottom track encased in a wooden bottom frame

Bottom track encased in a concrete ramp

All ECLIPSE System are composed of identical elements, which differ only dependingon the flow rates of the different systems.

At the bottom ECLIPSE Systems can provide for the application of a sill as exemplifiedin the figures below.

In this case there is a window with outward opening.The sill is applied to a wooden bottom frame with internalrebate. The minimum height recommended for optimalperformance of resistance to agents atmospheric is 25 mm.

Aluminum sill for outward opening with small sizeIn case of window opening outward, the sill can be

ECLIPSE SYSTEMSFeatures - The sill

Aluminum sill for outward opening

In case of window opening outward, the sill can be applied in wooden bottom frame, always with a internalrebate.If, howewer, has required a shift in a compact size, the internal bottom rebate may be reduced a minimunheight of 15 mm.

In this case there is a presence of a window with outward opening,which does not require special performance of resistance toweathering. Therefore, it is possible to apply the sill ina wooden bottom frame, withouth rebate.

For the lateral extremities of the sill are set plastic end caps, if you do not provide wooden claps.

Aluminum sill for outward opening - Winter Garden Applications

ECLIPSE E4Wood - Max 120 kg per panel

ECLIPSE E4

ECLIPSE E4 is the bi-folding system designed for windowsfrom important weights, always in wood.The maximum weight of each panel should not exceed 120 kg.

ECLIPSE E4 represents the system for maximumstrength and flow rate: in the extreme case of 16 panels, 8per side, the ECLIPSE E4 system allows to realize a window of total weight of 19,20 tons.

With ECLIPSE E4 system the panels can reach a maximumheight of 4 meters and a maximum width of 1,1 meter.The panel thickness can be from 45 to 85 mm.

In the bottom frame the ECLIPSE E4 system provide onlythe use of bottom track.


Whenever we collaborate with architects, designers and engineers, we are surprised athow much entusiasm, satisfaction and creativity radiating with ECLIPSE Systems.

Thank to the ECLIPSE Systems you can give free rein to the imagination:the wiew can be panoramic.

ANTI-CORROSION TESTS17,6 mts. Stainless steel, anodized aluminum120 kg and plastic parts of high quality are

maximum panel width 1,1 meter used to implement the maximum panel height 4 meters ECLIPSE E3CLD system.panel thickness 35-85 Each material is selected tomax panel numbers 8+8 obtain the best performance.

int/out

WEATHER RESISTANCEThe Centor hardware has been tested in accordancewith Australian Standard law AS2047, which providesminimum levels of performance required for resistanceto water and windIn addition, the ECLIPSE E3 and E4 were

ECLIPSE E4Wood- Max 120 kg per panel

ECLIPSE E4: Specificationsmaximum opening widthmaximum panel weight

opening

In addition, the ECLIPSE E3 and E4 werecertified in accordance with the provisions ofanti-Hurricane provided by Miami-Dade County ADJUSTMENTHurricane Standars. With the same The adjustment occurs whentechnology, the E4 system has reached the window is mounted, actingsatisfactory results on the air and water resistance, on the top carriers for theboth opening from outside or inside. vertical adjustment.

AIR RESISTANCEThe E4 system has achieved excellent resultsof air resistance, thanks to the ability hermeticseals and hinges, which prevent air infiltration,reaching high levels of performance.

The lateral adjustment occursacting on the pivot hinge seton the frame.

FUNCTIONALITY CYCLESThe E4 system has been subjected to the test cyclin, reaching 50.000 complete cycles ofopening and closing, without having no structuralfailure.Each component has also been tested for 100.000 cycles.

To one side is shown the development of a window, for example, with 4 panels all on one side.

Providing all the same panels, the folding window created with ECLIPSE E4 Systemmust be constructed in accordance with the gaps indicated in Figure 1.Among the frame tothe first panel the gap must be 9,5 mmAmong panel to panel the gap must be 8 mm.

Fig. 1

ECLIPSE E4Legno - Max 120 kg ad anta

In the Figure 2 we can see that, once closed the window, observed gap in the construction of the frame allows the ermetic closing of the panel, thanks to seals that act under pressure.It should be noted that the gap between the leaves is given automatically by hinges, which have a thickness of 8 mm.

Fig. 2

ECLIPSE E4 System: Application with bottom track


Finisht PriceAl. Nat.

Al. Nat.

Al. Nat.

Al. Nat.

Al. Nat.

White/Brown

White/Brown

White/Brown

Finish Price

ECLIPSE E4Finish Inox - Price List

ECLIPSE E4 - Finish InoxTRACKS AND SEALS

Code DescriptionE4TAM4N Top track mm 4000

E4TAM6N Top track mm 6000

E4TJP Joint for top tracks

E4FCM4N Bottom track mm 4000

E4FCM6N Bottom track mm 6000

E4QLS-B/W Seal for frame

AQ33-B/W Seal for panel

AQ109-B/W Seal for closing panel

CARRIERS AND HINGESCode Description Finish Price

Stainl.St.

Stainl.St.

Stainl.St.

Stainl.St.

Stainl.St.

Stainl.St.

Stainl.St.

Stainl.St.

Stainl.St.

Code DescriptionE4PSS Pivot hinge set

E4WPS Wall pivot hinge

E4ICSS Intermediate carrier set

E4OCSS End left carrier set

E4HHSS Handle half offset hinge set

E4HSS Handle hinge set

E4HHNHS Single half offset hinge

E4HNHS Singe hinge

E4HS External handle

CDS CENTRO DISTRIBUZIONE SICUREZZA SRL35010 LIMENA (PD) - ITALY - Via Pierobon 129

T. +39 049 8841502 F. +39 049 8846168

www.cdslimena.it - [email protected]

CDS_Eclipse E4_Catalogue

Documents