3--LG-Plasma

PLASMA TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : MF-056A

MODEL : 42PX3RV/RVB42PX3RV/RVB-ZA

website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html

- 2 -

CONTENTS

SAFETY PRECAUTIONS ....................................................................................3

DESCRIPTION OF CONTROLS ..........................................................................4

SPECIFICATIONS................................................................................................9

ADJUSTMENT INSTRUCTIONS .......................................................................11

TROUBLE SHOOTING GUIDE..........................................................................15

BLOCK DIAGRAM.............................................................................................24

EXPLODED VIEW..............................................................................................26

EXPLODED VIEW PARTS LIST ........................................................................27

REPLACEMENT PARTS LIST...........................................................................28

SCHEMATIC DIAGRAM.........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.

It will also protect the receiver and its components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.

When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by its Neck.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

POWERMUTE

TV/AV MULTIMEDIA

LIST ARC MENU

PR

PR

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM PIP/DW SLEEP

REVEAL TEXT/PIP PR+

WIN. SIZE MIXPIP PR-

POSITION TIMESWAP

HOLD INDEXPIP INPUT

?

i

I/II

MULTIMEDIASelects the Component, RGB or DVI

modes.switches the set on from standby.

PIP/DWSwitches the sub picture on or off.

Selects PIP or DW modes.PIP PR + /-

Selects a programme for the sub picture.SWAP

Alternates between main and sub pic-ture.

PIP INPUTSelects the input mode for the sub pic-

ture.WIN.SIZE

Adjusts the sub picture size.POSITION

Moves the sub picture to DD / EE or FF / GGdirection.

POWERswitches the set on from standby oroff to standby.

ARC Changes the picture format.

MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.

SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favourite programme is set toOff. Otherwise each press of this but-ton will select a stored favorite pro-gramme.

SSMTo select the sound appropriate toyour viewing programme character.

NUMBER buttons

SLEEPSets the sleep timer.

I/IISelects the language during dual lan-guage broadcast.Selects the sound output.

TEXT/*These buttons are used for teletext.For further details, see the Teletextsection.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.

LISTDisplays the programme table.

TV/AVSelects the TV, AV, Component, RGB

or DVI modes.switches the set on from standby.

MUTESwitches the sound on or off.

DD / EE (Programme Up/Down)selects a programme or a menu item.

switches the set on from standby.FF / GG (Volume Up/Down)

adjusts the volume.adjusts menu settings.

OKaccepts your selection or displays the

current mode.

PSMAdjusts the factory preset picture

according to the room.

SPLIT ZOOMEnlarge the screen with regular

ration.

- 4 -

DESCRIPTION OF CONTROLS

- 5 -

PRVOLMENUTV/AV OK

PRVOLMENUTV/AV OK

1 32 4 5 6 7

1. Remote Control Sensor

2. Power IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on.

3. Power ButtonSwitches the set on from standby or off to standby.

4. TV/AV ButtonSelects the TV, AV, Component, RGB or HDMI modes. Switches the set on from standby.

5. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.

6. OKAccepts your selection or displays the current mode.

7. DD / EE (Programme Up/Down)Selects a programme or a menu item.Switches the set on from standby.FF / GG (Volume Up/Down)Adjusts the volume.Adjusts menu settings.

- 6 -

S-VIDEO

VID

EO

AU

DIO

RL/

MO

NO

A/V INPUT2A/V INPUT2

AC INPUT

RS-232C INPUT(CONTROL/SERVICE)

S-VIDEOS-VIDEO

(MONO)

AUDIO AUDIO

L R

AUDIO AUDIO

L R

AUDIO AUDIO

L R

Antenna

VIDEO VIDEO

REMOTECONTROL

HDMI/DVI(VIDEO) AUDIO INPUT RGB INPUT

VIDEOVIDEO

COMPONENTCOMPONENT INPUT INPUT 2 2

COMPONENTCOMPONENT INPUT INPUT 1 1

MONITMONITOR OUTPUTOR OUTPUT

A/V INPUTA/V INPUT 1 1

VVARIABLE ARIABLE AUDIO OUTAUDIO OUT

1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER, DVD or STB to this socket.Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or theEMI Filter core along with separate cable.

2. CONTROL LOCK / REMOTE CONTROL

3. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.

4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.

5. VIDEO/AUDIO IN/OUT SOCKETS (A/V INPUT 1)Connect the video/audio out sockets of external equipmentto these sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in A/V INPUT 1.

6. VARIABLE AUDIO OUTPUT

7. ANTENNA INPUT

8. POWER CORD SOCKETThis the set operates on an AC power. The voltage is indicat-ed on the Specifications page. Never attempt to operate theset on DC power.

9. AUDIO/VIDEO INPUT (A/V INPUT 2)S-VIDEO/AUDIO IN SOCKETS

1 42 3 5 7 86

9

- 7 -

RGB / HDMI mode

Resolution

640x350

720x400

640x480

848x480

800x600

HorizontalFrequency(KHz)

VerticalFrequency(Hz)

852x480

832x624

1024x768

1152x864

1152x870

1280x960

1280x1024

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

56.25

60.31

72.18

75.00

85.06

74.55

60.00

70.06

75.02

85.00

60.05

70.01

75.00

75.06

60.02

60.02

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.500

37.799

39.375

31.500

37.799

39.375

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.677

54.348

63.995

67.500

68.681

60.023

63.981

- 8 -

AS mark

LG TV

Owners Manual

1.5V1.5V

Alkaline batteries Power Cord

POWERMUTE

TV/AV MULTIMEDIA

LIST ARC MENU

PR

PR

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM PIP/DW SLEEP

REVEAL TEXT/PIP PR+

WIN. SIZE MIXPIP PR-

POSITION TIMESWAP

HOLD INDEXPIP INPUT

?

i

I/II

Remote Control handset

- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.

- Contract your dealer for buying these items.

Optional Extras

AccessoriesAccessories

Tilt wall mounting bracket Video cables Audio cablesCeiling mounting bracket

40

4250

42

40

- Secure the TV assembly by joinning it to a wall by using the Eye Bolts/Wall brackets.

Joinning the TV assembly to the wall to protect the set tumbling

After the set must be mounted on a desktop, install the Eye Bolts on the set asshown.Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 2 bolts, (not supplied with the product),as shown.Match the height of the Eye Bolts and the wall brackets. Check to be sure the brackets are tightened securely.

Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.

2-Wall brackets

2-Eye Bolts

SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.

- 9 -

V Application RangeThis spec is applied to the 42PDP TV used MF-056A Chassis.

V Specification

Each part is tested as below without special appointment.1) Temperature : 255C (779F), CST : 4052) Relative Humidity: 6510%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification

Safety: CE, IEC specificationEMC : CE, IEC

V General Specification

1. Module Specification

Remark

Safety : IEC/EN60065, EMI : EN55013, EMS : EN55020

Model Name

42PX3RV-ZA

Market

EU

Remark

PDP

LGE SPEC

Maker : SONY/ Sanken

Specification

42 inch wide Color Display Module

16:9

PDP42V7xxxx

RGB Closed Type, Film Filter

1) Temp : 0~40 deg

2) Humidity : 0~85%

1) Temp : -20~60 deg

2) Humidity : 0~85%

100-240V~, 50/60Hz

No

1

2

3

4

5

6

Item

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

2. Model Specification (42PX3RV-ZA)

- 10 -

Item

Market

Broadcasting system

Available Channel

Receiving system

SCART Jack(3EA)

Video Input (2EA)

S-Video Input(3EA)

Component Input(1EA)

RGB Input(1EA)

HDMI Input(1EA)

Audio Input(4EA)

Wired Control

Audio variable out

No

1

2

3

4

5

6

7

8

9

10

11

12

13

Specification

EU

PAL B/G/I/D/K, NTSC

BAND PAL NTSC

VHF/UHF C1~C69 2~83

CATV S1~S47 1~71

Upper Heterodyne

PAL, SECAM, NTSC

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

RGB-DTV

HDMI-PC

HDMI-DTV

PC Audio, Component(1EA), AV(2EA)

Remark

4 System : PAL, SECAM, NTSC,PAL60



L/R Input

- 11 -

ADJUSTMENT INSTRUCTIONS

1. Application ObjectThese instructions apply to the MF-056A Chassis.

2. Specification(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolationtransformer will help protect test instrument.

(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of

255C of temperature and 6510% of relative humidity ifthere is no specific designation.

(4) The input voltage of the receiver must keep 100-220V,50/60Hz.

(5) The receiver must be operated for about 15 minutes priorto the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.

O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE

PATTERN.

[ Set is activated HEAT-RUN without signal generator inthis mode.

[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), afterimage may be occur in the black level part of thescreen.

3. Channel memory

3-1. Setting up the LGIDS1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.

3-2. Channel memory Method 1) Select PDP and Hurricane on Model dialog. And check

your connection in Communication dialog. (If yourconnection is NG, then set your PORT(COM1,2,3,...)correctly.)

2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see Ready.)

[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.

3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].

4) Click the [Download] button.It means the completion of the CH memory download if allitems show OK and Status is changed by PASS at thelower right corner of the window.

5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.

3-3 Sub program download

1) Select PDP and Hurricane on Model dialog. And checkyour connection in Communication dialog. (If yourconnection is NG, then set your PORT(COM1,2,3,...)correctly.)(Fig. 1)

(Fig. 3)

(Fig. 3-1)

- 12 -

2) Connect RS-232C cable and turn on the power. (Use thespecial Cable For Sub-program) (If your connection hascompleted, you can see Ready)

4. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments)

4-1. Test Equipment : D.M.M. 1EA

4-2. Adjustment Method[P/No 3501V00220A(Sanken PSU) B/D]

(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P807, connect

- terminal to GND pin of P807.3) After turning RV501, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; 0.5V)

(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P807, connect

terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; 0.5V)

5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download

5-1. Required Test Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID

TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable

5-2. Setting of device

5.3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC

& Cable.2) Turn on the PC & EDID Download Jig. And Execute the

S/W : EDID TESTER Ver,2.53) Set up S/W option

Repeat Number : 5Device Address : A0PageByte : 8

4) Power on the Set

5.4. Sequence of Adjustment

(1) DDC data of Analog-RGB1) Init the data

2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]

3) Set the S/W as below.4) Push the Write Data & Verifybutton. And confirm Yes.5) If the writing is finished, you will see the OK message.

Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)

(Fig. 4) Connection diagram of power adjustment for measuring

(Fig. 5) Connection Diagram of DDC download

- 13 -

6. Auto AV(CVBS) Color Balance

6-1. Required- This AV color balance adjustment should be performed beforwhite Balance Adjustment

6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator

: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)

6-3. Method of Auto Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar

Pattern) into video input.(42PX4RV-TA : AV1/AV2 Input 50Hz,42PX4RV-ZA : AV4/AV5 Input)

2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G(Vol. +) key operate to set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

7. Adjustment of White Balance

7-1. Required Equipment1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for auto adjustment)4) AV Pattern Generator

7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)

W Auto adjustment Map(RS-232C)

7-3. Adjustment of White Balance

O Operate the zero-calibration of the CA-100, then sticksensor to PDP module surface when you adjust.

O For manual adjustment, it is also possible by the followingsequence.

1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.

2) As below Fig.7-1, Supply 216Level (85 IRE) full screenpattern to Video input.(42PX4RV-TA : AV1/AV2 INPUT 50Hz,42PX4RV-ZA : AV4/AV5 INPUT)

3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the

INSTART key twice(White Balance) on R/C.6) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and offset) using D / E(CH +/-) keyon R/C.

7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.

8) Adjust it until color coordination becomes as below.(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)[MF-056A : 42PX4RV-TA/ZA] - VGA 42Bright : High Light : 80 20cdColor-Coordinate : High Light : X : 0.285 0.003

Y : 0.295 0.003Color Temperature : 9,300K 500K

9) When adjustment is completed, Exit adjustment modeusing EXIT key on R/C

(Fig. 7-1) Pattern for Adjustment of White Balance

216 Level (85 IRE)

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j a

j b

j c

j d

j e

j f

Stop bit

1

Parity

NONE

MF-056A : RT-42PX40/ RZ-42PX40

ProtocolSetting

Data Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern

(Fig. 7) Connection Diagram of Auto W/B adjustment

MSPG-2100 /MSTG- 5200

216 Level (85 IRE)

COLORANALYZERTYPE ; CA-100

CVBSsignalinput

RS-232C Serial Communication

- 14 -

8. Auto Component Color Balance

8-1. Required Test Equipment1) Remote controller for adjustment2) 802F Pattern Generator

(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)

8-2. Method of Auto Component Color Balance1) Input the Component 720p 100% Color Bar signal into

Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means complete adjustment

9. Auto RGB Color Balance

9-1. Required Test Equipment1) Remote controller for adjustment2) 802F Pattern Generator, Master (MSPG-925FA), etc.

(Which has XGA 60Hz PC Format output with standard(0.7Vpp) horizontal black and white pattern as Fig.10)

9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz horizontal black and white

pattern into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

9. Default Value in Adjustment mode

9-1. Auto Color Balance (Component/RGB)

9-2. White Balance

Level : 0

Level : 255

(Fig. 9) Auto RGB Color Balance Test Pattern

(Fig. 10) Default Value on OSD

(Fig. 10-1) Default Value on OSD

Auto Color Balance(HEX)

Auto-RGB) G To SetRed ) Offset1)) 80Green)Offset1)) 80Blue) Offset1)) 80Red) Offset2)) 80Green)Offset2)) 80Blue) Offset2)) 80Red) Gain)) 80Green)Gain)) 80Blue) Gain)) 80Reset)) G To Set

White Balance(Hex)

Red ) Gain)) 80Red ) Offset)) 80Green)Gain)) 80Green)Offset)) 80Blue) Gain)) 80Blue) Offset)) 80Reset)) G To Set

(Fig. 8) Auto Component Color Balance Test Pattern

- 15 -

TROUBLE SHOOTING GUIDE

1. Power Board

1-1. The whole flowchart which it follows in voltage output state

Start check

Manufacture enterprisemeaning of a passage

1. Check the Power Offcondition.

Doesn't the screen whole come

out?

It is identical with Power Off

condition?

Yes

Yes

No

No

No

No

No

2. Check the Interfacesignal condition.

Is the Interface signal operated?

Yes

3. Check the St-by 5Vsignal circuit.

Doesn't the low pressure output

come out?

Doesn't the St-by 5V signal

come out?

Yes

Yes

No

4. Check the 5V Monitorsignal circuit.

Doesn't the 5V Monitor signal

come out?

Yes

7. Check the VSC Vs-ONsignal

Doesn't the high tension output

come out?

Doesn't the VSC signal Vs-ON

come out?

Yes

Yes

Doeshigh tension

output voltage dropoccur?

When theY B/D Module

Input Connector isremoved, does output

voltage Drop occurs?

When theY,Z B/D Module

input connector is remove,does Power B/D hightension

output voltage dropoccur?

Yes No No

9. Check the PowerBoard Output high

tension circuit

Yes

10. Check the Z B/DModule output circuit

Yes

When theZ B/D Module

Input Connector isremoved, does output

voltage Drop occurs?

11. Check the Y B/DModule output circuit

Yes

No

8. Check the Vs, Vavoltage output circuit.

Doesn't the Vs, Va voltage output

come out?

Yes

No

No

5. Check the VSC RL-ONsignal.

Doesn't the VSC signal RL-ON

come out?

Yes

6. Check the VSC lowpressure output

Doesn't the VSC low pressureoutput come out?

Yes

- 16 -

1-2. Sony Power Board Structure

1 2 3

T502: Vs Trans

T702: Va Trans

T101: St-by Trans

T103: Low Voltage Trans

- 17 -

1-3. Sanken Power Board Structure

1 2 3

T221: Vs Trans

T271: Va Trans

T121: St-by Trans

T201: Low Voltage Trans

- 18 -

2. No Power

(1) Symptom Doest minute discharge at module. Non does not come in into the front LED.

(2) Check following

Is plug in power cord? Plug in power cord.

Yes

No

Is the Line Filter and Power BoardCable connected?

Connect the Cable.

Yes

No

Is the Fuse(F101) normal on PowerBoard ?

Replace the Fuse.

Yes

No

Is the Power Board and 7P of VSCBoard Cable connected?

Connect the Cable.

Yes

No

After the cable connect isremoved to Power Board(exceptthe CN101 connection cable), theAC voltage marking is authorizedon manual. When ST-BY 5V is notoperated, replace Power Board.

- 19 -

3. Protect Mode

(1) Symptom After once shining, it does not discharge minutely

from module The Rely falls(The sound is audible click) It is converted with the color where the front LED

is red from green.

(2) Check following

Is the Power Boardnormal?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace theconnector.

Replace Y-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Boardnormal?

Replace X-Board.

Is the output voltage normalafter remove P1, 2, 4, 9, 10

connector of Ctrl-B/D?

Yes

No Yes

Is the Y- Boardnormal?

Is the output voltagenormal after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)

Yes

No Yes Yes

Replace Z-Board.

Is the Z- Boardnormal?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)

Yes

No Yes

Is the X- Boardnormal?

Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of

X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D

Yes

No Yes

Is the VSC Boardnormal?

Is the output voltage normalafter remove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, 1100 normaloperation: Replace VSC Board

Yes

No

Is the COF of X, Y, Znormal?

No

Yes

Yes

- 20 -

4. No Raster

(1) Symptom Doest minute discharge at module. It maintains the condition where the front LED is green.

(2) Check following

Is the Power Boardnormal?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replaceconnector.

Replace Y-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Boardnormal?

Replace X-Board.


connector of Ctrl-B/D?

Yes

No Yes

Is the Y- Boardnormal?

Is normal the outputvoltage after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)

Yes

No Yes Yes

Replace Z-Board.

Is the Z- Boardnormal?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is the Fuse(FS1, FS2) on Z-B/Dnormal? (In case of open is replace)

Yes

No Yes

Is the X- Boardnormal?


connector of X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D

Yes

No Yes


Is the output voltage normalafter remove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, P1100 normaloperation: Replace VSC Board

Yes

No

Is the COF of X, Y, Znormal?

No

Yes

Yes

- 21 -

5. In case of occurring strange screen into specific mode

5-1. In case the OSD does not displayed

(1) Symptom LED is green The minute discharge continuously becomes accomplished from module

(2) Check following

Is the LVDS cablenormal?


Is the LVDS cableconnected well?

Cable inserts well.Yes

No

No

Yes

Does the FIL8532IC(IC800) Operates ?

Replace FIL8532IC(IC800).

No

Is the Ctrl Board ofModule normal?

Replace Ctrl B/D.No

No

YesReplace VSC B/D

Replace the cable.Yes

- 22 -

5-2. In case of doest display the screen into specific mode

(1) Symptom The screen does not become the display from specific input mode

(RF, AV, Component, RGB, DVI).

(2) Check following Check the all input mode should become normality display. Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become

normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

(4) In the case of becomes unusual display from RF, AV mode

(5) In the case of becomes unusual display from Component, RGB mode

(6) In the case of becomes unusual display from HDMI mode

Is the Tuner normal?

Is the CXA2069Qnormal?

Is the Tuner Cableconnected well?

Cable inserts well.Yes

No

No

Yes

Is the FIL8532normal?

Replace the Tuner

No

Is normal the Input voltage, IICCommunication and CVBS output?

Yes

Is the Input voltage, IICCommunication and HV

sync normal?

NoReplace the IC

No


sync normal?

NoReplace the IC

No

Is the CXA2069Qnormal?

Yes



sync normal?

NoReplace the IC

No


sync normal?

NoReplace the IC

No



sync normal?

NoReplace the IC

No

Is the Sil9011normal?

Yes



sync normal?

NoReplace the IC

No


sync normal?

NoReplace IC

No

- 23 -

6. In case of no sound

(1) Symptom LED is green Screen display but sound is not output

(2) Check following

Is the SPK cablenormal?

Is the SPK cableconnected well?

Cable inserts well.

No

No

Replace IC400

No

Replace IC401

No

Replace SPK cableYes

Yes

Is the RF/ AV/Component/ RGB/

HDMI soundnormal?

No Does IC400Operates ?

Does IC401Operates ?

Replace IC402

No

Does IC402Operates ?

Replace VSC B/D

Yes Yes

- 24 -

BLOCK DIAGRAMca

ble

'

MEMO

- 25 -

- 26 -

EXPLODED VIEW

300

301

304

302

202206

203

204

201

205

580

410

530

121

601600

120

501

401

400

303

207

200

520

430

- 27 -

120 6401VD0032A SPEAKER ASSEMBLY, FULL RANGE(R) RZ-42PX30 FILM TYPE

121 6401VD0033A SPEAKER ASSEMBLY, FULL RANGE(L) RZ-42PX30 FILM TYPE

200 6348Q-E080W PDP, 42 852*480 PDP42V70102.ADLGB

201 6871QCH053A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V7 FPGA

202 6871QDH084A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV TOP B/D

203 6871QDH085A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV BTM B/D

204 6871QLH047A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V7 XL B/D

205 6871QRH055A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V7 XR B/D

206 6871QYH036A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V7

207 6871QZH041A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V7

300 3091V00816D CABINET ASSEMBLY, RZ-42PX31 STEREO MF056C FILM TYPE SKD

3091V00816H CABINET ASSEMBLY, 42PX3RVB STEREO RF052C FILM TYPE SKD

301 4980V01203B SUPPORTER, ASSY AL FILTER TOP RZ-42PX30 C/SKD

302 4980V01204B SUPPORTER, ASSY AL FILTER BOTTOM RZ-42PX30 C/SKD

303 4980V01205B SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX30 C/SKD

304 4980V01206B SUPPORTER, ASSY AL FILTER LEFT RZ-42PX30 C/SKD

400 3809V00605B BACK COVER ASSEMBLY, 42PX17/30 CHASSIS CHANGE C/SKD

3809V00605G BACK COVER ASSEMBLY, 42PX3RVB CHASSIS CHANGE BK SPRAY

401 3301V00085A PLATE ASSEMBLY, ASSY 3300V00552A RZ-42PX30 PLATE TUNER COVER

3301V00085E PLATE ASSEMBLY, ASSY 3300V00552A 42PX3RVB PLATE TUNER COVER BK

410 4980V01071B SUPPORTER, ASSY AL VERTICAL RZ-42PX10 SKD

430 3501V00216E BOARD ASSEMBLY, ASSY AP-42DX30 MF056C C/SKD

3501V00216F BOARD ASSEMBLY, ASSY AP-42DX30 MF056C BK C/SKD

501 3301V00083A PLATE ASSEMBLY, ASSY 3300V00550A 3301V00084A 42PX17/30 PLATE TUNER

3301V00083G PLATE ASSEMBLY, ASSY 42PX3RVB BK PRESS AV PLATE

520 6871VMMF71A PWB(PCB) ASSEMBLY,MAIN MF-056A RZ-42PX31 SUSAB SKD

530 6871VSMS36B PWB(PCB) ASSEMBLY,SUB CONT MF056C RZ-42PX30 SKD NO VINYL

580 6709V00010A POWER SUPPLY ASSEMBLY, PDP 42INCH MF056A 350W YPSU-J006A

600 6871VSMS18B PWB(PCB) ASSEMBLY,SUB A/V MF056A RT/RZ-42PX40 SIDE A/V SUSAB

601 4811V00118A BRACKET ASSEMBLY, DECO RZ-42PX10 RF043B SIDE AV

4811V00118N BRACKET ASSEMBLY, SIDE AV 42PX3RVB-ZA AF044A BLACK

EXPLODED VIEW PARTS LIST

No. Part No. Descriptions

MIC39100 MICREL 3P SOT223 R/TPBA033FP-E2 ROHM 3P-SOP,TO252-3KA7809R, FAIRCHILD 2P D-PAK, R/TPSC156515M-1.8TR SEMTECH 5P/TO-263-5BA033FP-E2 ROHM 3P-SOP,TO252-3BA033FP-E2 ROHM 3P-SOP,TO252-3BA033FP-E2 ROHM 3P-SOP,TO252-3MIC39100 MICREL 3P SOT223 R/TP SC156515M-1.8TR SEMTECH 5P/TO-263-5KIA78R05F KEC 5PIN DPAK R/TP 1A,5VSC156515M-1.8TR 5P/TO-263-5MIC39100 MICREL 3P SOT223 R/TPSII9011CLU(PB FREE) SILICON IMAGE 128PAT24C02N-10SI-2.7 ATMEL 8P SOICMC34063ADR2G ON SEMI SO-8PCXA2069Q QFP64 BK I2C BUS AV S/WLA7217M MFP14 TP SYNC SEPARATORMSP4410K MICRONAS 80P/PQFPNSP-2100A,LF NEOFIDELITY TQFPTAS5122DCAR 56P/TSSOP R/TP 30WKA4558D 8SOP OP AMP74HC14D 14SOP TP SHITTER TRIGGERAT24C02N-10SI-2.7 ATMEL 8P SOIC74HC14D 14SOP TP SHITTER TRIGGERICL3232CBNZ INTERSIL 16P/SOP R/TPFLI8125AA-LF GENESIS 208P/PQFPAT24C32AN-10SI-2.7 ATMEL 8PIN SOPSST25VF040-20-4C-S2AE-T SST SOIC 8PFLI8532BC-LF GENESIS 416P/PBGA24LC256-I/SM 8P,SOP TP 256K IICK4D261638F-LC50,LF TSOPII 66PK4D261638F-LC50,LF TSOPII 66P

BSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECKRA102S R/TP KEC SOT23 CHIP TRCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KEC

REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

Q104Q1200Q200Q201Q202Q203Q204Q205Q206Q207Q300Q301Q302Q303Q304Q305Q400Q401Q402Q403Q404Q405Q407Q408Q409Q410Q411

D1005D1006D1007D1008D1009D1010D1012D1013D102D103D104D105D106D108D1100D1105D1106D1107D1109D1110D112D113D114

D1200

0TR387500AA0TR387500AA0TR150400BA0TR387500AA0TR387500AA0TR150400BA0TR150400BA0TR387500AA0TR150400BA0TR150400BA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR150400BA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR102008AA0TR387500AA0TR102008AA0TR387500AA0TR387500AA0TR387500AA

0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD200009AF0DD200009AF0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD184009AA

CHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SA1504S(ASY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SA1504S(ASY) KECCHIP 2SA1504S(ASY) KECCHIP 2SC3875S(ALY) KECCHIP 2SA1504S(ASY) KECCHIP 2SA1504S(ASY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SA1504S(ASY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECKRA102S R/TP KEC SOT23 CHIP TRCHIP 2SC3875S(ALY) KECKRA102S R/TP KEC SOT23 CHIP TRCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KECCHIP 2SC3875S(ALY) KEC

KDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECRU2M V(1) TP SANKENRU2M V(1) TP SANKENKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS184 TP KEC - 85V - 300MA


IC1000IC1001IC1002IC1003IC1004IC1005IC1100IC1101IC1102IC1103IC1104IC1105IC1200IC1201IC202IC300IC301IC400IC401IC402IC403IC404IC500IC502IC600IC700IC701IC703IC800IC802IC901IC902

IC1202IC1203IC200IC201IC503IC504Q100Q1000Q1001Q1002Q1003Q1004Q101Q101Q102Q102Q103

0IPRPML001A0IMCRRH001A0IMCRFA010A0IPMG00027A0IMCRRH001A0IMCRRH001A0IMCRRH001A0IPRPML001A0IPMG00027A0IPMGKE030A0IPMG00027A0IPRPML001A0IPRPS5005A0IMMRAL014B0IPMGON013B0ISO206900A0ISA721700C

0IMCRMN028B0ILNR00015A0IMCRTI028C0ISS455880A0IPH741400E

0IMMRAL014B0IPH741400E0IPRP00009A0IMCR02006A0IMMRAL025A0IMMR00004A0IMCR02005A0IMP242560A0IMMR00002A0IMMR00002A

0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR102008AA0TR387500AA0TR387500AA

IC

TRANSISTOR

- 28 -

DIODE

- 29 -


D1201D300D500D501D502D504D505D506

ZD100ZD101ZD107ZD300ZD301ZD400ZD600

C1000C1005C1007C1009C1010C1019C1022C103C1030C1043C1046C1047C1050C1051C1064C1065C1066C1067C1068C1069C1071C1073C108C1082C1083C1084C1085C1087C1098C1099C1102C1105C1107C1108C1110

0DS113379BA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DZRM00248A0DR050008AA

0CE477SF6DC0CE477SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE107SF6DC0CE4763F6180CE476SF6DC0CE476SF6DC0CE477SF6DC0CE476SF6DC0CE477SF6DC0CE477SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE477SF6DC0CE477SF6DC0CE227SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE477SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE477SF6DC

1SS133 T-72 TP ROHM KOREA DO34 90VKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECSD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ARLZ8.2B-TE11 ROHM R/TP LLDS(LL-34)SD05.TC R/TP SEMTECH SOD323 5V 5A 15A

470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF SRE 16V M FL TP547UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD220UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD


C1115C1116C1117C1118C1119C1120C1126C1135C1136C1137C1138C1148C1149C1150C1151C1154C1159C1162C1165C1166C117C118

C1185C1186C1187C1188C1189C119

C1190C1191C1192C1193C1195C1199C120

C1200C1201C121

C1225C1230C1231C1245C1247C129C130

C1302C1304C1306C1309C131C1311C1312

0CE477DJ6180CE477SF6DC0CE227VF6DC0CE477SF6DC0CE477DJ6180CE227VF6DC0CE477SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE227SF6DC0CE106SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE106SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE106SF6DC0CE106SF6DC0CE106SF6DC0CE106SF6DC0CE106SF6DC0CK105DF64A0CK105DF64A0CE106SF6DC0CE476SF6DC0CE227SF6DC0CE227SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC

470UF STD 35V 20% FL TP 5470UF MVG 16V 20% R/TP(SMD) SMD220UF MV 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD470UF STD 35V 20% FL TP 5220UF MV 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP220UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD1UF 2012 16V 20% R/TP F(Y5V)1UF 2012 16V 20% R/TP F(Y5V)10UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP220UF MVG 16V 20% R/TP(SMD) SMD220UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP

CAPACITOR

For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;

CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic

RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible

- 30 -


C1313C1314C1315C1316C1317C1318C135C1414C1415C1419C1420C1424C1425C1428C1438C1441C1506C203C204C208C210C211C214C215C221C238C241C300C304C305C307C310C315C318C319C320C321C325C328C330C338C340C342C347C402C403C413C418C425C444C451C456

0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE475SK6DC0CE475SK6DC0CE106SF6DC0CK105DF64A0CE106SF6DC0CE106SH6DC0CE106SH6DC0CE106SH6DC0CE106SH6DC0CE476SF6DC0CE475SK6DC0CE477SF6DC0CE477SF6DC0CE475SK6DC0CE477SF6DC0CE106SF6DC0CE475SK6DC0CE477SF6DC0CE107SF6DC0CE476SK6D80CE107SF6DC0CE226SF6DC0CE107SF6DC0CE476SF6DC0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CE476SF6DC0CE105SK6DC0CE105SK6DC0CE476SF6DC0CE226SF6DC0CE335VK6DC0CE107SF6DC0CE226SF6DC0CE107SF6DC0CK105DF64A0CK105DF64A

100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP4.7UF MVG 50V 20% SMD R/TP4.7UF MVG 50V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD1UF 2012 16V 20% R/TP F(Y5V)10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 25V 20% SMD R/TP10UF MVG 25V 20% SMD R/TP10UF MVG 25V 20% SMD R/TP10UF MVG 25V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP4.7UF MVG 50V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD4.7UF MVG 50V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD4.7UF MVG 50V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP47UF MVG,MC 50V 20% SMD TAPPING100UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP47UF MVG 16V 20% SMD R/TP1UF MVG 50V 20% SMD R/TP1UF MVG 50V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP3.3UF MV 50V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP1UF 2012 16V 20% R/TP F(Y5V)1UF 2012 16V 20% R/TP F(Y5V)


C457C462C463C464C465C480C481C482C483C484C495C527C610C728C729C730C731C735C737C739C745C750C752C760C762C764C767C771C832C833C834C835C836C837C838C839C840C851C853C884C896C901C904C905C930C950

L1000L1101L1102L1103

0CE335VK6DC0CE107SF6DC0CE106SF6DC0CE106SF6DC0CE106SK6DC0CE108DJ6180CE475SK6DC0CE475SK6DC0CF4741L4380CF4741L4380CE108DJ6180CE476SF6DC0CE107SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC

6140VB0004B6140VB0004B6140VB0004B6140VB0004B

3.3UF MV 50V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 50V 20% SMD R/TP1000UF STD 35V 20% FL TP 54.7UF MVG 50V 20% SMD R/TP4.7UF MVG 50V 20% SMD R/TP0.47UF D 63V 5% TP 5 M/PE NI0.47UF D 63V 5% TP 5 M/PE NI1000UF STD 35V 20% FL TP 547UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP

26UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.4




COIL

- 31 -


L1104L404L405L406L407

AR1200AR1201AR1202AR1203AR1204AR1205AR700AR701AR702AR703AR704AR705AR806AR807AR808AR809AR810AR811AR812AR813AR814AR815AR816AR817R230

D1003D1103LD101

SW101SW102SW103SW104SW105SW106SW107SW108SW700SW800

L100

6140VB0004B6140VB0032A6140VB0032A6140VB0032A6140VB0032A

0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RRZVTA001B0RD0331H609

0DL233309AC0DL233309AC0DL200000CA

140-315A140-315A140-315A140-315A140-315A140-315A140-315A140-315A

6600VR1004A6600VR1004A

6200J000013

26UH 1UEWPHY 22.5TURN YL-9N 0.4DBF-1015A 15.5UH 10PIE DIGITAL AUDIODBF-1015A 15.5UH 10PIE DIGITAL AUDIODBF-1015A 15.5UH 10PIE DIGITAL AUDIODBF-1015A 15.5UH 10PIE DIGITAL AUDIO

22 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%MNR14-E0A-J-510 R OHM 51 OHM 5%3.3 OHM 1/2 W 5.00% TA52

SAM2333 GREEN/RED GREEN:10MCD, RED:6MCDSAM2333 GREEN/RED GREEN:10MCD, RED:6MCDSAM5670(DL-2LRG) BK Y-GREEN -

TACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VTACT SKHV17910B LG C&D 12VSKHMPW 5P CHIP TACT J-ALPSSKHMPW 5P CHIP TACT J-ALPS

MLB-321611-0500P-N2 MAG LAYERS


L1004L1005L1006L1007L1008L1009L101

L1010L1011L1012L1013L1014L1015L1016L1017L1018L1019L1020L1021L1022L1023L1024L1025L110

L1105L1106L1107L1108L1109L111L1110L1111L1112L1113L1115L1116L1117L1118L1119L1120L1121L1122L1123L1125L1126L1127L1128L1129L1130L114L115L119

6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200JB8010L6200JB8010L

MLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-201209-1000L-N2 MAG LAYERSMLB-201209-1000L-N2 MAG LAYERSMLB-201209-1000L-N2 MAG LAYERS




SWITCH

FILTER & CRYSTAL

LED

RESISTOR

- 32 -


L120L1204L1205L1206L1207L1208L1209L121L122L123L124L125L126L200L201L202L203L204L300L301L302L400L401L402L403L408L409L410L500L502L503L506L604

X1200X300X400X700X800

JK100JK101JK101JK102JK103JK104JK1200JK400JK502JK600

6200JB8010L6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136210VC0005A6210VC0005A6210VC0005A6210VC0005A6210VC0005A6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200JB8010L6200J0000136200J0000136212AB2845A

166-E02F156-A02M

6212AB2844A6212AB2844A

6612J00043C6612J00043C6613V00026A6612J00043C6612J10012A6612J00038B6612B00015B6612J00037A6612F00087A6612F00087A

MLB-201209-1000L-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSBK2125 HS 750 2X1.25X0.85MM R/TPBK2125 HS 750 2X1.25X0.85MM R/TPBK2125 HS 750 2X1.25X0.85MM R/TPBK2125 HS 750 2X1.25X0.85MM R/TPBK2125 HS 750 2X1.25X0.85MM R/TPMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-201209-1000L-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-201209-1000L-N2 MAG LAYERSMLB-201209-1000L-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSMLB-321611-0500P-N2 MAG LAYERSRESONATOR,CRYSTAL ABLS-27.000MHZRESONATOR,CERAMIC CSBLA500KECZF09RESONATOR,CRYSTAL HC49U 18.432MHZRESONATOR,CRYSTAL ABLS-19.6608MHZRESONATOR,CRYSTAL ABLS-19.6608MHZ

UPJ-R1-031 UGCOM S/TUPJ-R1-031 UGCOM S/TUJB-03-28A UGCOM 6613V00004SUPJ-R1-031 UGCOM S/TUJB-05-02C GR/BL/RD/WH/RD 1*5 SHIELDUJB-03-25B UGCOM 6612J00038ADC1R019WDH JAE 0.5MM,19PIN+2PIN,HDMIUJB-02-12A UGCOM 2P RCAUEJ-CV-032 UGCOM EAR JACKUEJ-CV-032 UGCOM EAR JACK


A1A2A3

C1C2C3

JK500JK601PA101TU200TU201

3828VA0545F6710V00126R6410VEH003C

6850VA0004J6851V00022C6850J00005B6630G70016A6630G70017A6712000002B6700MF0010B6700MF0010A

MANUAL,OWNERS MF056A EU/42PX3RVREMOTE CONTROLLER, RF043A PIPPOWER CORD, M2511A-001 2800MM

CABLE,COAXIAL UL1365#26 150MM UCA-EX-069CABLE,COAXIAL UL1365#26 VW-1,SOLDERLESSCABLE,DVI LVDS UL20276 AWG30 500MMCONNECTOR, A03-7071-094 SPGCONNECTOR, A02-0915-101 SPGREMOTE CONTROLLER RECEIVER,KSM-603SM12E-1TUNER, TAFM-W502P MINI 4SYSTEM SUBTUNER, TAUM-W501P MINI 4 SYSTEM MAIN

ACCESSORIES

MISCELLANEOUS

JACK

PRINTED CIRCUIT BOARDMAIN (TOP) MAIN (BOTTOM )

SIDE A/V(BOTTOM)

CONTROL

Apr., 2005Printed in KoreaP/NO : 3828VD0209Q

#EV#

3--LG-Plasma

Documents