Lg Plasma Rz-60py10

website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html

PLASMA TV SERVICE MANUALCHASSIS : RF-043B

MODEL : RZ-60PY10

CAUTIONBEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CONTENTS

SAFETY PRECAUTIONS ...................................................................................3 DESCRIPTION OF CONTROLS .........................................................................4 SPECIFICATIONS .............................................................................................14 ADJUSTMENT INSTRUCTIONS ......................................................................16 TROUBLE SHOOTING GUIDE ..........................................................................21 BLOCK DIAGRAM .............................................................................................32 EXPLODED VIEW ..............................................................................................34 EXPLODED VIEW PARTS LIST ........................................................................35 REPLACEMENT PARTS LIST...........................................................................36 SCHEMATIC DIAGRAM ........................................................................................ PRINTED CIRCUIT BOARD ..................................................................................

- 2 -

SAFETY PRECAUTIONSIMPORT ANT SAFETY NOTICEMany electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General GuidanceAn isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this monitor is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts. Due to high vacuum and large surface area of picture tube, extreme care should be used in handling the Picture Tube. Do not lift the Picture tube by it's Neck.

Leakage Current Hot Check (See below Figure)Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

AC Volt-meter

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

To Instrument's exposed METALLIC PARTS

Good Earth Ground such as WATER PIPE, CONDUIT etc.0.15uF

1.5 Kohm/10W

- 3 -

DESCRIPTION OF CONTROLS

Remote Control Key Functions- When using the remote control aim it at the remote control sensor of the set. - There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.

Displays the selected device.TV

MODE Selects another device. TV/AV Selects the TV, AV, Component, RGB or DVI modes. MULTIMEDIA Selects the Component, RGB or DVI modes. NUMBER buttonsTV/AV

VCR DVD CABLE STB AUDIO

POWER Switches the set on from standby or off to standby. ARC Changes the picture format. MUTE Switches the sound on or off. Q.VIEW Returns to the previously viewed programme. SSM To select the sound appropriate to your viewing programme character. VOL +/- (Volume Up/Down) Increases/decreases sound level. PR +/- (Programme Up/Down) Selects a programme. EXIT Clears all on-screen displays and returns to TV viewing from any menu. TEXT/ (option) These buttons are used for teletext. For further details, see the Teletext section. Note : In teletext mode, the PIP PR +/-, SWAP and PIP INPUT buttons are used for teletext function.

MODE ARC

POWER MUTE

MULTIM

EDIA

1FAVOURITE Selects a favorite programme. PSM Adjusts the factory preset picture according to the room. MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes. PIP/DW Switches the sub picture on or off. Selects PIP or DW modes. PIP PR + /Selects a program for the sub picture. SWAP Alternates between main and sub picture. PIP INPUT Selects the input mode for the sub picture. WIN.SIZE Adjusts the sub picture size. WIN.POSITION Moves the sub picture to D / E or F / G direction.

2 5 8 0

3 6 9Q.VIEW

4 7FAVOURITE

PSM VOL PR

SSM

PIP/DW TEXT/ MENU EXIT

*

OK

PIP PRPIP PR+ SWAP

PIP INPUT

OK accepts your selection or displays the current mode.D / E or F / G Adjusts menu settings. Selects menu item.

PLAY

PAUSE

STOP

RECORD

REW

FF

SKIP

DVD BUTTONS Controls a LG DVD player. VCR BUTTONS Controls a LG video cassette recorder. LIST Displays the program table. SPLIT ZOOM Enlarge the screen with regular ration.REVEAL?

WIN.SIZE WIN.POSITION SLEEP I/II

SLEEP Sets the sleep timer. I/II Selects the language during dual language broadcast. Selects the sound output.

LIST

SPLIT ZOOM

- 4 -

- Shown is a simplified representation of the set. - Here shown may be somewhat different from your set.

Remote Control Sensor Power Standby Indicator Illuminates red in standby mode, Illuminates green when the set is turned on

ON/OFF

TV/AV

MENU

VOL

PR

TV/AV Button Selects the TV, AV, Component, RGB or DVI modes. If OSD is displayed, selects menu item. Main Power Button MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes.

D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby. F / G (Volume Up/Down) adjusts the volume. adjusts menu settings.

- 5 -

AV 5

VIDEO

S-VIDEO

6

COMPONENT

AUDIO

Y REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT AUDIO INPUT RGB INPUT

PB

PR

L L(MONO)

RAV1 AV2 AV3

R

Antenna

R AUDIO L/MONO

8

AC INPUT

S-VIDEO

VIDEOAV4

AUDIO

1

2

3

4

5

7

1. REMOTE CONTROL 2. RS-232C INPUT(CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC. 3. DVI INPUT / AUDIO INPUT / RGB INPUT Connect the monitor output socket of the PERSONAL COMPUTER to this socket. Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI Fillter core along with separete cable. 4. COMPONENT INPUT Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of AUDIO INPUT. AUDIO/VIDEO IN SOCKETS (AV4) Connect the audio/video out sockets of external equipment to these sockets. S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEO socket. Connect the audio out sockets of the VCR to the audio sockets as in AV4.

5. ANTENNA INPUT 6. EURO SCART SOCKET Connect the euro scart socket of the VCR to these sockets. 7. POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power. 8. AUDIO/VIDEO IN SOCKETS (AV5) S-VIDEO/AUDIO IN SOCKETS

- 6 -

External Equipment Viewing SetupsAntenna Connection- Be careful for the bronze wire not to be bended in connecting to antenna input port.

Apartments (connecting to wall antenna socket)

wall antenna socketCOMPONENT AUDIO

Y TE OL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT AUDIO INPUT RGB INPUT

PB

PR

L L(MONO)

RAV1 AV2 AV3

R

Antenna

AC INPUT

S-VIDEO

VIDEOAV4

AUDIO

RF coaxial wire (75 ohms)VHF antenna UHF antenna outdoor antenna

< Back panel of the set >

Private house (connecting to wall outdoor antenna)

Watching VCR- When connecting the set to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white, Audio (R) -red). - Connect the VIDEO INPUT socket (yellow) to the VIDEO INPUT on the set. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set. - Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. (Refer to p. 25) If a 4:3 picture format is used; the fixed image may remain visible on the screen. - To avoid picture noise (interference), leave an adequate distance between the VCR and set. Watching TV programmes - Turn the set on and select the programme you want. Watching VCR 1. Use the TV/AV button on the remote control to select AV1, AV2, AV3, AV4 or AV5. - If both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-VIDEO can be received. 2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owners manual)< Back panel of the set >

< VCR >

- 7 -

Watching Cable TV- After subscribing for a local cable TV station and installing a converter you can watch cable TV. - For further information of cable TV, contact the local cable TV station.< Back panel of the set >

To watch cable TV 1. Use the TV/AV button on the remote control to select AV1, AV2, AV3, AV4 or AV5. 2. Tune to cable service provided channels using the cable box.

< Cable box >

Watching external AV source- When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set. How to use 1. Use the TV/AV button on the remote control to select AV1, AV2, AV3, AV4 or AV5. 2. Operate the corresponding external equipment. See external equipment operating guide.< Back panel of the set >

CamcorderR AUDIO L VIDEO

Video game set

- 8 -

R

Watching DVDHow to connect Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of AUDIO INPUT. How to use 1. Turn on the DVD player, and insert a DVD. 2. Use TV/AV or MULTIMEDIA button on the remote control to select Component. Refer to the DVD player's manual for operating instructions.< Back panel of the set >

R

R

COMPONENT

AUDIO

Y OTE ROL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT AUDIO INPUT RGB INPUT

PB

PR

L L(MONO)

R R Antenna

S-VIDEO

VIDEOAV4

AUDIO

Component Input ports You can get better picture quality if you connect DVD player with component input ports as below. Component ports of the set Video output ports of DVD player Y Y Y Y Y PB PR

< DVD player >

Pr Pb B-Y R-Y Cb Cr P B PR

- 9 -

R

R

Connecting PC- To enjoy vivid picture and sound, connect a PC to the set. - Avoid keeping a fixed image on the sets screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. - Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of PC accordingly. - There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card. - The synchronization input form for Horizontal and Vertical frequencies is separate. Setup Instructions to Connect a PC to your set - We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality. - If the resolution of PC is over UXGA, there will be no picture on the set. - Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI output port of the PC to the DVI INPUT port on the set. - Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set). - If using a sound card, adjust PC sound as required. - This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically to use this set. - DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode. - If required, adjust the set settings for Plug and Play functionally. - If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI INPUT to display the PC on the set. If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other mode is set to Plug and Play automatically by the set.) - DOS mode may not work depending on video card if using a DVI-I cable.

< Back panel of the set >

COMPONENT

AUDIO

Y 32C INPUT ROL/SERVICE) DVI INPUT AUDIO INPUT RGB INPUT

PB

PR

L L(MONO)

R R An

PC Setup 1. Turn on the PC and apply power to the set. 2. Turn on the display by pressing the POWER button on the sets remote control. 3. Use the TV/AV or MULTIMEDIA button on the remote control to select the RGB or DVI input source. 4. Set the resolution output of the PC to SXGA or under (1280 x 1024, 60Hz). (Refer to p. 13)

S-VIDEO

VIDEOAV4

AUDIO

- 10 -

Displayable Monitor SpecificationRGB / DVI modeResolution 640x350 720x400 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 31.469 37.927 31.469 35.000 640x480 37.861 37.500 43.269 31.500 848x480 37.799 39.375 31.500 852x480 37.799 39.375 35.156 37.879 800x600 48.077 46.875 53.674 832x624 49.725 48.363 1024x768 56.476 60.023 68.677 47.700 1360x768 59.625 68.500 47.700 1366x768 59.625 69.500 54.348 1152x864 63.995 67.500 77.487 1152x870 1280x768 1280x960 1280x1024 68.681 47.693 60.091 68.504 60.023 63.981 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 (RGB) 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.00 75.02 85.00 60.00 75.02 85.00 60.05 70.01 75.00 85.00 75.06 60.00 75.00 85.00 60.02 60.02

- 11 -

AccessoriesTVVCR DVD CABLE STB AUDIOTV/AVMULTIMED IA

MODE ARC

POWER MUTE

1 4 7FAVOURITE

2 5 8 0

3 6 9Q.VIEW

PSM VOL PR

SSM

PIP/DW TEXT/ MENU EXIT

OK

PIP PRPIP PR+ SWAP

PIP INPUT

PLAY

PAUSE

STOP

RECORD

LG TVAS mark

1.5V 1.5V

REW

FF

SKIP

REVEAL?

WIN.SIZE WIN.POSITION SLEEP I/II

LIST

SPLIT ZOOM

Owners Manual

Alkaline batteries

Remote Control handset

Power Cord

2-TV bracket bolts (Only RZ-60PY10/11 series : 6-TV bracket bolts)

2-TV brackets 2-Wall brackets (optional)

6-RING SPACER (Only RZ-60PY10/11 series)

Joinning the TV assembly to the wall to protect the set tumbling- Secure the TV assembly by joinning it to a wall by using the TV/Wall brackets. After the set must be mounted on s desk top, install the TV brackets on the TV as shown. Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the product), as shown. Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.

Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown.

Optional ExtrasOptional extras can be changed or modified for quality improvement without any notification new optional extras can be added. Contract your dealer for buying these items.

50

42

40

40

42

50

Tilt wall mounting bracket

Wall mounting bracket (Only RZ-60PY10/11 series)

Tilt wall mounting bracket (Only RZ-60PY10/11 series)

Ceiling mounting bracket

Ceiling mounting bracket

Desktop stand (optional)

Video cables

Audio cables

- 12 -

40

4240

42

50

Installation Options The set can be installed in different ways such as on a wall, or on a desktop etc.

Desktop Pedestal Installation The set can be mounted on a desk as shown above. (For further information, refer to the optional 'Desktop Stand Installation and Setup Guide'.) Speakers and speaker stands shown are optional, and are shown for example only.

To Install on a Desktop Pedestal mount minimum allowable clearances for adequate ventilation.

Wall Mount: Horizontal Installation The set can be installed on a wall as shown above. (For further information, refer to the optional Wall Mounting Bracket Installation and Setup Guide.) Speakers are optional, and are shown for illustration only.

To Mount on a Wall Wall mount minimum allowable clearances for adequate ventilation.10cm

3cm

10cm

10cm

10cm

Install the RING SPACER with the bolts on the set as shown. (Only RZ-60PY10/11 series) 1. Put the RING SPACER in the holes of the bolts before connecting to the wall mounting bracket. 2. When you connect the wall mounting bracket to the set, connect to it by using the bolts, (supplied with the product), as shown.

- 13 -

SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.V

Application RangeThis spec is applied to the 42PDP TV used RF-043B Chassis.

V

SpecificationEach part is tested as below without special appointment. 1) Temperature : 25 5C (77 9F) 2) Relative Humidity: 65 10% 3) Power Voltage: Standard Input voltage (100V-240V~ 50/60Hz) * Standard Voltage of each product is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 20 minutes prior to the adjustment.

V

Test and Inspection Method1) Performance : LGE TV test method followed. 2) Demanded other specification Safety: CE, IEC specification EMC : CE, IEC Model Name RZ-60PY10 Market EU Remark Safety : IEC/EN60095 EMI : EN55013

EMS : EN55020

V

General Specification1. General Specification No 1 2 3 4 5 Item Display Screen Device Aspect Ratio PDP Module Screen Filter Operating Environment Specification 50 inch wide Color Display Module 16:9 PDP60X5xxxx, RGB Closed Type 45% Total light transmittance (E- Mesh) 1) Temp : 0~40 deg 2) Humidity : 0~85% 6 Storage Environment 1) Temp : -20~60 deg 2) Humidity : 0~85% 7 Input Voltage 100 - 240V~, 50/60Hz Maker : LG(innotek) LGE SPEC Maker : LG Chemical PDP Remark

- 14 -

2. Model Specification No 8 9 10 11 12 Market Broadcasting Receiving system Scart Jack (3EA) Video Input (2EA) Item EU PAL B/G/I/D/K, SECAM L/L Upper Heterodyne PAL, SECAM PAL, SECAM, NTSC 4 System : PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60 13 S-Video Input(2EA) PAL, SECAM, NTSC 4 System : PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60 14 15 16 17 18 Component Input(1EA) RGB Input(1EA) DVI Input(1EA) Audio Input(4EA) Wired Control Y/Cb/Cr, Y/Pb/Pr RGB-PC DVI-PC PC Audio, Component, AV(2EA) Discrete IR DVI-D L/R Input Specification Remark

- 15 -

ADJUSTMENT INSTRUCTIONS1. Application ObjectThese instructions apply to the RF-043A Chassis. (2) select Create Shortcut from the menu with the left mouse button and move the shortcut icon onto the desktop. (3) Double-click on the LGIDS icon on the desktop to execute the program.

2. Specification(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 255C of temperature and 6510% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 100~220V, 50/60Hz. (5) The receiver must be operated for about 15 minutes prior to the adjustment. After RGB Full white HEAT-RUN Mode, the receiver must be operated prior to adjustment. O Enter into HEAT-RUN MODE 1) Press the POWER ON KEY on R/C for adjustment. 2) OSD display and screen display 100% full WHITE PATTERN.O

3-2. Channel memory Method(1) Check if Malibu has been selected on Model. (2) Check if Connection under Communication is OK. (3) If it is NG , look on PORT(COM1,2,3...) and make sure that its on the right port. (4) After connecting RS-232C cable, turn on the power. If it the communication has been done correctly, READY is displayed at the lower right corner of the window shown as (Fig. 2). [ When the TV SET is not assembled completely and only the PCB is supplied by Stand-by 5V, download at the Stand-by state (LED is Red).

[ Set is activated HEAT-RUN without signal generator in this mode. [ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

Caution) If you turn on a still screen more than 20 minutes (Especially digital pattern, cross hatch pattern), a after image may be occur in the black level part of the screen.

3. Channel memory3-1. Setting up the LGIDS(1) Install the LGIDS. (idsinst.exe) After installation is completed, check if the file shown on (Fig. 1) has been created. After using the right mouse button to click on LGIDS,

(Fig. 2)

(5) Select proper CH_memory file(*.nvm) for each model at [NVRAM Download] $ [Write Batch] Next, select proper binary file(*.bin) including the CH information for each model at [NVRAM File]. (6) Click the [Download] button. It means the completion of the CH memory download if all items show OK and Status is changed by PASS at the lower right corner of the window. (7) If you want to check whether the CH information is memorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CH information downloaded.

(Fig. 1)

- 16 -

4-2. KEY Generation

(Fig. 3)

4. HDCP Download4-1. LGIDS Setting Method(1) Click on setup to install in your directory. (2) After installation is completed, check if the file shown on (Fig. 4) has been created. (3) Copy the KEY from source CD into the HDCP directory which was installed just now. (DVI_orderNo_2003_data) (Fig. 5) (1) Click on Key Generation (G). (2) Input the number of the key in Generation count. ex) If 100 Keys are required, then just register 100 and next time it will automatically get 101. (3) Input file : When installing the program for the first time, you must find the original KEY that you copied and open it. It is crucial that you copy the original KEY into this directory. When you use Generation, the information is recorded in Config.ini. (4) Click on Generation (1) If it is done correctly, you will see Job is Success.(2) Click on close(3) (5) Check the Generation Data(Confirmation its possible within HDCP\CreatedKeyFile)

(Fig. 4) (4) After running HDCP(application program) which is inside the HDCP directory, setup the Communication. Port : COM1(modification possible) BaudRate : 115200

(Fig. 6)

- 17 -

(6) It is possible to check how many Generations are created at this point. (Fig. 7) shows that you have created 130 Generations and you will start from 131 next time.

(Fig. 7) (Fig. 10) Abnormal State

4-3. HDCP Download Method(1) Input power of Stand-By 5V. (Download must be executed only when it is on Stand-by) (2) The RS-232C(9PIN) must be connected to the COM1 on the PC.

(4) If abnormal state (Fig. 10) display then (3) execute.

Each PCB assembly must be checked by check JIG set. (Because power PCB Assembly damages to PDP Module, especially be careful)

5. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments)5-1. Test Equipment : D.M.M. 1EA 5-2. Connection Diagram for MeasuringRefer to (Fig 11). (Fig. 8) (3) If all the preparation is completed, click on Download.

5-3. Adjustment Method for P/No. 3501V00180A B/D(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN. 2) Connect + terminal of D.M.M to Va pin of P805, connect - terminal to GND pin of P805. 3) After turning RV501, voltage of D.M.M adjustment as same as Va voltage which on lable of panel right/top (Deviation; 0.5V)

(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P805, connect terminal to GND pin of P805. 2) After turning RV401, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V)

(Fig. 9) Normal State

- 18 -

5-4. Adjustment Method for P/No. 3501V00182A B/D(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN. 2) Connect + terminal of D.M.M to Va pin of P805, connect - terminal to GND pin of P805. 3) After turning RV601, voltage of D.M.M adjustment as same as Va voltage which on lable of panel right/top (Deviation; 0.5V)

6. DDC Data Input6-1. Required Test Equipment(1) A jig for adjusting PC, DDC (PC serial to D-sub Connection equipment) (2) S/W for writing DDC (EDID Data Write & Read) (3) D-sub 15P Cable, D-Sub to DVI Connector (Connect to DVI Jack)

6-2. Setting of Device

(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P805, connect terminal to GND pin of P805. 2) After turning RV401, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V)

6-3. Preparation for Adjustment(1) Set devices as above and turn the PC, jig on. (2) Put S/W for writing DDC (EDID data Write & Read) into operation. (operated in DOS mode.)

6-4. Sequence of Adjustment(1) DDC Data Input for Analog-RGB< 3501V00180A >

1) Put the set on the table and turn the power on. 2) Connect PC Serial to D-sub 15P Cable of jig for DDC adjustment to RGB terminal (D-Sub 15Pin). 3) Operate S/W for DDC record and select DDC data for Analog RGB in Model Menu. 4) Operate EDID Write command. 5) Operate EDID Read command and check whether Check Sum is 53. 6) If Check Sum is not 53, repeat 3) ~ 4). 7) If Check Sum is 53, DDC data for Analog-RGB input is completed.

< 3501V00182A >

(2) DDC Data input for Digital-RGB(DVI)1) Connect PC Serial to DVI Cable of jig for DDC adjustment to DVI terminal (DVI Jack). 2) Operate S/W for DDC record and select DDC data for digital RGB in model menu. 3) Operate EDID Write command. 4) Operate EDID Read command and check whether Check sum is D2(1page), BF(2page). 5) If Check sum is not D2(1page), BF(2page), repeat 3) ~ 4). 6) If Check sum is D2(1page), BF(2page), DDC data for Analog-RGB input is completed.

(Fig. 11) Connection Diagram of Power Adjustment for Measuring

- 19 -

7. Adjustment of White Balance7-1. Required EquipmentColor Analyzer (CA-100 or same product)

8-2. Method of Auto RGB Color Balance(1) Input RGB Source : Component 480p/576p 16 Gray Scale Pattern At this time, except Pb and Pr signal, only Y signal insert. (2) Press ADJ KEY on R/C for adjustment. (3) Press Vol. + KEY and operate To set. (4) Auto-RGB OK means completed adjustment.

7-2. Connection Diagram of Equipment for Measuring

9. Auto RGB Color Balance216 Gray Level Full Size Pattern 60Hz AV Signal Input

9-1. Required Test EquipmentWindow

Pattern Equipment: PC Pattern Generator (VG828, VG854, 801GF, MSP3240A) (16 Gray Scale Pattern output(RGB output Level: 0.7Vp-p)

RS-232C Serial Communication

MSPG-2100 or MSTG-5200

9-2. Method of Auto RGB Color Balance(1) Input RGB Source : 16 Gray Scale Pattern output (RGB output Level : 0.7Vp-p) (2) Press ADJ KEY on R/C for adjustment. (3) Press Vol. + KEY and operate To SET. (4) Auto-RGB OK means completed adjustment.

(Fig. 12) White Balance Adjustment

7-3. Adjustment of White BalanceO O

Operate the Zero-calibration of the CA-100, then stick sensor to PDP module surface when you adjust. For manual adjustment, it is also possible by the following sequence.

(1) Select white pattern of heat-run mode by pressing power on key on remote control for adjustment then operate heat run more than 15 minutes. (2) Supply Gray Pattern (216 Level Full Size Pattern: Signal level=0.59V0.03V) signal to VIDEO input. (AV2 Input 60Hz) (Refer to Fig. 12) (3) Press the FRONT-AV KEY on R/C for converting input mode. (4) To adjust, stick sensor to 216 Gray Level Pattern, press ADJ key twice(White Balance) on remote control. For adjustment and D, E on remote control for adjustment mode to select Red Gain and Green Gain, press VOL +, Key and adjust it until color coordination becomes as below. [ 216 Gray level=Signal level 0.59V0.03V X; 0.2830.003, Y; 0.2970.003 Color Temperature; 9,300K500K (5) Exit adjustment mode using A Key.

(Fig. 13) Auto RGB/ Component Color Balance Test Pattern

10. Auto Adjustment Map(RS-232C)RF-043A Type Baud Rate 115200 Data bit 8 RS232 Stop bit 1 Parity NONE

Index Cmd1 Cmd2 Data Min Value Max Value R Gain G Gain j j j j j j a b c d e f 00(00) 00(00) 00(00) 00(00) 00(00) 00(00) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF)

8. Auto Component Color Balance8-1. Required Test EquipmentPattern Equipment: MSP3240A or same product (16 Gray Scale Pattern output(Component output Level: 0.7Vp-p)

Protocol B Gain Setting R Offset G Offset B Offset

- 20 -

TROUBLE SHOOTING GUIDE1. Power Board1-1. The whole flowchart which it follows in voltage output state

Start check

Doesn't the screen whole come out?

Yes

It is identical with Power Off condition? Yes

No

Is the Interface signal operated?

Yes 2. Check the Interface signal condition.

No

1. Check the Power Off condition.

Doesn't the low pressure output come out?

Yes

Doesn't the St-by 5V signal come out? Yes

No

Doesn't the 5V Monitor signal come out? Yes 4. Check the 5V Monitor signal circuit.

No

Doesn't the VSC signal RL-ON come out? Yes 5. Check the VSC RL-ON signal.

No

3. Check the St-by 5V signal circuit.

Doesn't the high tension output come out?

Yes

Doesn't the VSC signal Vs-ON come out? Yes

No

Doesn't the Vs, Va voltage output come out? Yes 8. Check the Vs, Va voltage output circuit.

Doesn't the VSC low pressure output come out? Yes 6. Check the VSC low pressure output

No

No

7. Check the VSC Vs-ON signal

High tension output voltage Drop it occurs?

Yes

When remove the Y, Z B/D Module Input Connector, Power Board high tension output voltage Drop it occurs? Yes 9. Check the Power Board Output high tension circuit

No

When remove the Y B/D Module Input Connector, output voltage Drop it occurs? Yes 10. Check the Z B/D Module Coutput circuit

No

When remove the Z B/D Module Input Connector, output voltage Drop it occurs? Yes 11. Check the Y B/D Module Coutput circuit

No

Manufacture enterprise meaning of a passage

- 21 -

1-2. Sony Power Board Structure

T502: Vs Trans T702: Va Trans

1

2

3

T101: St-by Trans T103: Low Voltage Trans

- 22 -

1-3. Sanken Power Board Structure

T221: Vs Trans T271: Va Trans

1

2

3

T121: St-by Trans T201: Low Voltage Trans

- 23 -

2. No Power(1) Symptom

Doest minute discharge at module. Non does not come in into the front LED.

(2) Check followNo Is plug in power cord? Yes No Connect Cable. Plug in power cord.

Is connect the Line Filter and Power Switch Cable? Yes

Is connect the Power Switch and Power Board Cable? Yes

No Connect Cable.

Is normal the Fuse(F101) on Power Board? Yes

No Replace Fuse.

Is connect the Power Board and 7P of VSC Board Cable? Yes

No Connect Cable.

Is connect the Power Switch and Power Board Cable? Yes

No Connect Cable.

After remove the cable connect to Power Board(except the CN101 connection cable), authorizes the AC voltage marking on manual. When ST-BY 5V does not operate, replace Power Board.

- 24 -

3. Protect Mode(1) SymptomAfter once shining, it does not discharge minutely from module The Rely falls(The sound is audible click) It is converted with the color where the front LED is red from green.

(2) Check followIs normal the Power Board? Yes Is normal the each connector? Yes Is normal the Y- Board? Yes Is normal the Z- Board? Yes Is normal the X- Board? Yes Is normal the Ctrl Board? Yes Is normal the VSC Board? Yes Is normal the COF of X, Y, Z? No After crisis COF of each board, check the normality operates. If in case normality operates, correspondence COF Fail is replace the module. No Is normal the output voltage after remove P1000, P1200? Yes After remove P1000 normal operation: Replace Analog Board After remove P1200 normal operation: Replace Digital Board No Is normal the output voltage after remove P1, 2, 101, 300, 701, 702 connector of Ctrl-B/D? Yes Replace X-Board. No Is normal the output voltage after remove P1, 2, 3, 4, 6, 7 connector of X-B/D? Yes After remove P1, P2, P3, P4 output voltage normality: Replace Right X-B/D After remove P6, P7 output voltage normality: Replace Left X-B/D No Is normal the Fuse(FS1, FS2) on ZB/D? (In case of open is replace) Yes Is normal the output voltage after remove P1 connector of Z-B/D? Yes Replace Z-Board. No Is normal the Fuse(F52) on Y-B/D? (In case of open is replace) Yes Is normal the output voltage after remove P5, P6 connector of Y-B/D? Yes Replace Y-Board. No After connecting well each connector, the normality it operates? No Replace connector. No Is output the normality Low/High voltage except Stand-by 5V? No Replace Power Board.

- 25 -

4. No Raster(1) Symptom

Doest minute discharge at module. It maintains the condition where the front LED is green.

(2) Check followIs normal the Power Board? Yes Is normal the each connector? Yes Is normal the Y- Board? Yes Is normal the Z- Board? Yes Is normal the X- Board? Yes Is normal the Ctrl Board? Yes Is normal the VSC Board? Yes Is normal the COF of X, Y, Z? No After crisis COF of each board, check the normality operates. If in case normality operates, correspondence COF Fail is replace the module. No Is normal the output voltage after remove P1000, P1200? Yes After remove P1000 normal operation: Replace Analog Board After remove P1200 normal operation: Replace Digital Board No Is normal the output voltage after remove P1, 2, 101, 300, 701, 702 connector of Ctrl-B/D? Yes Replace X-Board. No Is normal the output voltage after remove P1, 2, 3, 4, 6, 7 connector of X-B/D? Yes After remove P1, P2, P3, P4 output voltage normality: Replace Right X-B/D After remove P6, P7 output voltage normality: Replace Left X-B/D No Is normal the Fuse(FS1, FS2) on ZB/D? (In case of open is replace) Yes Is normal the output voltage after remove P1 connector of Z-B/D? Yes Replace Z-Board. No Is normal the Fuse(F52) on Y-B/D? (In case of open is replace) Yes Is normal the output voltage after remove P5, P6 connector of Y-B/D? Yes Replace Y-Board. No After connecting well each connector, the normality it operates? No Replace connector. No Is output the normality Low/High voltage except Stand-by 5V? No Replace Power Board.

- 26 -

5. In case of occur strange screen into specific mode5-1. In case of doest display the OSD(1) Symptom

LED is green The minute discharge continuously becomes accomplished from module

(2) Check followIs normal the LVDS cable? No Is the LVDS cable connected well? No Yes Replace cable.

Yes

Cable inserts well.

Is normal the VSC Digital Board?

No

Operates the Thine Yes IC(IC1100)? No

Operates the IEP(IC500)? No

Yes

Operates the Scaler(IC700)?

Yes

Replace Thine IC(IC1100).

Replace IEP(IC500).

Replace Scaler(IC700).

Is normal the Ctrl Board of Module?

No Replace Ctrl B/D.

- 27 -

5-2. In case of doest display the screen into specific mode(1) Symptom

The screen does not become the display from specific input mode (RF, AV, Component, RGB, DVI).

(2) Check follow

Check the all input mode should become normality display. Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF modeNo Is normal the Tuner? Is the Tuner Cable connected well? No Yes Cable inserts well. No No Replace IC Replace Tuner Yes Is normal the Input voltage, IIC Communication and CVBS output? No

Is normal the CXA2069Q? Yes Is normal the VPC3230?

Is normal the Input voltage, IIC Communication and HV sync?

No

Is normal the Input voltage, IIC Communication and HV sync?

No Replace IC

(4) In the case of becomes unusual display from RF, AV modeIs normal the CXA2069Q? Yes Is normal the VPC3230? No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC

- 28 -

(5) In the case of becomes unusual display from RF, AV, Component 480i modeIs normal the VPC3230? Yes No Is normal the S2300? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC

(6) In the case of becomes unusual display from Component DTV modeIs normal the 74LS123? Yes Is normal the CXA2101? Yes Is normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC

- 29 -

(7) In the case of becomes unusual display from RGB DTV modeIs normal the CXA2101? Yes Is normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC

(8) In the case of becomes unusual display from RGB PC modeIs normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC

(8) In the case of becomes unusual display from DVI modeNo Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC

- 30 -

6. In case of no sound(1) Symptom

LED is green Screen display but sound is not output

(2) Check followIs normal the SPK cable? No Is the SPK cable connected well? No Yes Cable inserts well. Yes Replace SPK cable

Is normal the RGB/DVI sound?

No

Is the Flat cable connected well? No Cable inserts well.

Yes Operates the IC800? No Replace IC800

Yes Operates the IC801? No Replace IC801

Yes

Yes Is normal the RF/AV/Component sound? No Replace VSC Analog B/D

Operates the IC802? No Replace IC802

- 31 -

WIRE IRRS232_RX/ TX Co mp _480I/ P RGB PC

TX IR

74ACT253

TX_Out

Co mp / RGB_SW

RS232ST3232CRGB DTV Comp DTV CXA_RGB

RX0/1,TX0/1

RGB PC/ DTV

M52758F Sw it c hADC w/ PLL

RGB_Dat a

ZHINE

RGB (PC/DTV)74HCT08 CXA2101 IEPDVI RX w/ HDCP

RGB H/ V 24

g m 1601 Sc aler ( Malib u)

24

SCL/ SDA

24LC21RX/ TXC DVI_Dat a Text Vid eo f o r Text

Main_Vid eo / 24 Sub _Vid eo / Co mp / RGB_SW 8 Fro m Malib u

10

DV I (PC/DTV)24LC21

RX/ TX0/ 1/ 2,

SCL/ SDA

Dig it al BOARDMain_V Main_YC

TX0/ 1/ 2/ 3/ C Disp _En SDATA SCLK, SLE

Scart 1VPC3230 (M ) Video Decoder

TV OUT Vin1 ( CVBS) YCb Cr S2300 / DeInt erlac er 8

1H RGB

HY5DU283222A SDRAM ( 128MB)

Vin2 ( CVBS )

BLOCK DIAGRAM

- 32 Main_V

Scart 2

MNT OUT

Scart 3CXA2069Q SWITCHMain_YC TU_Main TU_Sub Vin4 Text _V YCin4

Vin3 (CVBS )

RF

Tuner (M)

VPC3230 (S) Video Decoder

HY57V64322 SDRAM ( 8MB)

AM29LV F-ROM (1MB )

Tuner ( S )

CVBS

S-VHS

SDA6001 Text Processor

AM29LV160 F-ROM

Po s-t p ro c es sing Blo c k is o m it t ed . so alled JEPICO, in this c ase -c TMDS TX is also req uired . So und Pro c es sing Blo c k Diag ram is sep arat ed . . RCA yp e Blo c k Diag ram is also -t sep arat ed . .HYV641620 SRAM

Co mp _480i Vin5 YCin5 74LS123

Comp1 (DVD/DTV )

Co mp _Y

Analo g BOARDCo mp _480I/ P To Malib u

CVBS S-VHS

Sid e - AV BOARD

Di gt a l BOARD74ACT253 TMDS Transf er / Thine Analo g RGB DVI g m1501H TQFP 128K DDR Memo ry

WIRE IR

Tx

RS232 ST3232C 74HCT08 RGB PC M52758FP IC202( MUX) 24LC21

IIS

IEP

HV

RGB ( PC/ DTV)

ZHINE

IIS

RGB DTV CXA2101 24LC21 RGB_DTV VPORT ( 24b it) SVPORT ( 16b it) Flash ROM 512K/ 1M

DVI ( PC/ DTV)

IIS

LVDS 31PIN

M52758FP IC204 DAC_RGB DTV2_Co mp DTV_Co mp M37136 ( OTP) DVD_MAIN M52758FP IC400( MUX) S/ DVD_Co mp CAB_Co mb RGB_24Bit

FLI2300

Analo g BOARD

HY57V64322 SDRAM ( 8MB)

- 33 DVD2_MAIN ALT_Y_480I_MAIN ALT_Y2_480I_MAIN MAIN_YOUT CAB_VIN COMB_YOUT MAIN_COUT UPD64083 COMB_COUT CXA2069Q MAIN_VOUT MAIN_YOUT Tuner ( S) LA7151M SW CVBS/ Y ALT_Y_480I_SUB ALT_Y2_480I_SUB DVD_SUB DVD2_SUB SUB_YOUT SUB_COUT

Co m p 1

Co mp

( DVD/ DT V)

Co mp 2

Co m p 2

( DVD/ DTV)

CVBS IN

VIN1

VPC3230 ( MAIN) M656 8 Bit

CVBS OUT

MNT_OUT

S-VHS

Y/ CIN1

RF

Tuner ( M)

Sid e A/ V

VPC3230 ( SUB) S656 8 Bit M62320FP ( I2C Exp end er)

Side-CVBS

VIN2

Sid e S-VHS

Y/ CIN2

EXPLODED VIEW301 310 308 311 120 314 309 313 314 307 550 312 300 305 302 551

303 301 101 102

306 304 121

570

212 211 210 201 209 200

208 205 204 620 202 206 203 580 400

540 610

600 541 501

530

401 520 560 630

- 34 -

EXPLODED VIEW PARTS LISTNo.101 102 120 121 200 201 202 203 204 205 206 208 209 210 211 212 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 400 401 501 520 530 540 541 550 551 560 570 580 600 610 620 630

Part No.5900V08004A 4980V00A48B 6401VD0017B 6401VD0016B 6348Q-B038S 6871QDH035C 6871QDH036C 6871QLH046A 6871QXH029A 6871QRH053A 6871QYH035A 6871QCH055A 6871QZH040A 6871QLH045A 6871QXH028A 6871QRH052A 3091V00664A 4972V00114B 4980V00A94C 4980V00A97C 4980V00A95C 5230V00022C 4980V00A96C 4811V00112A 4811V00113A 3210V00255A 3210V00256A 3210V00253A 3790V00745G 3790V00745H 4972V00113B 3210V00254C 3809V00460B 3301V00025J 3301V00026E 6871VMMS74A 6871VSMZ56A 6871VSME94A 5020V00436D 6871VSME91A 4811V00114D 6871VSMG25A 6871VSMF12C 3501V00193A 6871VSMG21A 3501V00194A 3501V00195A 3501V00173B

DescriptionFAN,DC F8025L12B2-RG DONG YANG 80MM 12V 120MA 2300RPM 79G L 300MM SUPPORTER, FAN EGI PRESS DU-60PY10 SPEAKER ASSEMBLY, RZ-60PY10 C/SKD WOOFER TWEETER L SPEAKER ASSEMBLY, RZ-60PY10 C/SKD WOOFER TWEETER R PDP, 60 16:9 1365*768 PDP60X50554.ADLGA PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT TOP(60X5) SN755866PZP PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT BOTTOM(60X5) SN755866PZP PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 60X5A X LEFT BOTTOM PWB(PCB) ASSEMBLY,DISPLAY XRCT ASSY HAND INSERT 60X5A X CENTER BOTTOM PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 60X5A X RIGHT BOTTOM PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 60X5A 4LAYER PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 60X5A, 4023, LVDS PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 60X5A 4LAYER PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 60X5A LEFT TOP PWB(PCB) ASSEMBLY,DISPLAY XRCT ASSY HAND INSERT 60X5A X CENTER TOP PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 60X5A X RIGHT TOP CABINET ASSEMBLY, DN-60PY10 CABINET ASSY(MOLD) FIXER, FRAME EGI DU-60PY10 LEFT PRESS SUPPORTER, FILTER AL RZ-60PY10 TOP ASSY C/SKD SUPPORTER, FILTER AL RZ-60PY10 LEFT ASSY C/SKD SUPPORTER, FILTER AL RZ-60PY10 BOTTOM ASSY C/SKD FILTER(MECH), DU-60PY10 LG-CHEMICAL FLATRON PLASMA DELETE LG FOR AMREICA SUPPORTER, FILTER AL RZ-60PY10 RIGHT ASSY C/SKD BRACKET ASSEMBLY, SPEAKER DU-60PY10 SPK GRILL ASSY R BRACKET ASSEMBLY, SPEAKER DU-60PY10 SPK GRILLE ASSY L FRAME FRONT SIDE AL DU-60PY10 RIGHT WITH SPK FRAME FRONT SIDE AL DU-60PY10 LEFT WITH SPK FRAME FRONT UPPER AL DU-60PY10 . WINDOW, DECO RZ-60PY10 RIGHT BK PRINT WINDOW, DECO RZ-60PY10 LEFT BK PRINT FIXER, FRAME EGI DU-60PY10 RIGHT PRESS FRAME BOTTOM AL RZ-60PY10 BACK COVER ASSEMBLY, RZ-60PY10 BACK COVER ASSY C/SKD PLATE ASSEMBLY, ASSY . VSC TUNER COVER RZ-60PY10 C/SKD PLATE ASSEMBLY, ASSY 3300V00338_339 RZ-60PY10 C/SKD PWB(PCB) ASSEMBLY,MAIN RF-043B DIGITAL B/D MANUAL PWB(PCB) ASSEMBLY,SUB TUNER RF043B MALIBU RZ50 SUB ANALOG MANUAL PWB(PCB) ASSEMBLY,SUB PSW AF044A POWER SWITCH BUTTON, POWER RZ-60PY10 ABS, AF-303S 1KEY SKD PWB(PCB) ASSEMBLY,SUB A/V RF043A MALIBU SIDE AV BRACKET ASSEMBLY, SIDE AV RZ-60PY10 ASSY C/SKD PWB(PCB) ASSEMBLY,SUB CONT RF043B RZ-60PY10 LOCAL_KEY PWB(PCB) ASSEMBLY,SUB LED AF044A DN-60PY10 INDEX BOARD ASSEMBLY POWER DN-60PY10 AF044A 9YPSU0001CG LGINNOTEK MAIN B/D PWB(PCB) ASSEMBLY,SUB SUB RF043A FAN CTRL BOARD ASSEMBLY, PFC DN-60PY10 AF044A 9YPSU0001BG LGINNOTEK PFC B/D BOARD ASSEMBLY, POWER DN-60PY10 AF044A 9YPSU0001AG LGINNOTEK AC-IN B/D BOARD ASSEMBLY, ASSY AP-60DY10 WITHOUT PACKING SKD

- 35 -

REPLACEMENT PARTS LISTLOCA. NO PART NO DESCRIPTION LOCA. NO IC701 IC702 IC800 IC800 IC801 IC801 IC802 IC803 IC805 PART NO 0IMMRAL025A 0IKE704200J 0IMCRMN028A 0IMMRHY020B 0IMCRNL001A 0IMMRMR023A 0IMCRTI028C 0IPRPJR017A 0IKE704200J DESCRIPTION AT24C32AN-10SI-2.7 ATMEL 8PIN SOP TP 32K 3.3V KIA7042AF SOT-89 TP 4.2V VOLTAGE DETECTOR MSP4410G-QA-C13-101 HY5DU283222AQ-5 HYNIX 100P LQFP NSP-6241B NEOFIDELITY 64P TQFP MX29LV800TTC-70 MACRONIX 48PIN TAS5122DCAR 56P/TSSOP NJU26901E2 JRC 8P,EMP KIA7042AF SOT-89 TP 4.2V

ICIC100 IC100 IC1000 IC1001 IC1002 IC1003 IC1004 IC101 IC101 IC102 IC102 IC103 IC104 IC105 IC1100 IC1200 IC1201 IC1202 IC1300 IC1301 IC1302 IC1303 IC1304 IC1305 IC1306 IC200 IC201 IC202 IC203 IC204 IC400 IC401 IC402 IC403 IC500 IC500 IC5001 IC5002 IC5003 IC5004 IC5005 IC5006 IC501 IC502 IC503 IC504 IC600 IC600 IC601 IC700 IC700 0IMI623200B 0IMMRAL014B 0IMCRFA010A 0IPRPML001A 0IMCRSH001A 0ITK118100B 0IMCRSH001A 0IMI623200B 0IMMRAL014B 0IMCRTI003A 0IMI623200B 0IMCRTI021A 0IMCRTI021A 0IMCRFA015A 0IMCRTH002A 0IMCRSJ001A 0IPRPML001A 0IMCRFA010A 0IMCRRH001A 0IMCRSH001A 0IMCRSH001A 0IMCRRH001A 0IMCRSJ001A 0IMCRRH001A 0IPRPML001A 0IFA742530B 0IMCRSG010A 0IMCRMI006A 0ISTLSG009A 0ISTLSG009A 0ISO206900A 0ISO210100B 0IMCRTI003A 0ISTLSG009A 0ICTMLG018A 0IMCRMN023A 0IKE780500Q 0ISH092100B 0ISH092100B 0ISH122100B 0IMI623200B 0IDS162100B 0IMMRHY001F 0IMMRMR006B 0IMCRAL006A 0IKE702700D 0IIT323000E 0IMCRGN002C 0IMMRHY033A 0IIT323000E 0IPRPGN012A M62320FP,I/O EXPANDER 16P SOP TP AT24C02N-10SI-2.7 ATMEL 8P SOIC KA7809R, FAIRCHILD 2P D-PAK MIC39100 MICREL 3P SOT223 PQ05DZ1U SHARP 5, SMD TYPE TK11840L 8P SOT23L PQ05DZ1U SHARP 5, SMD TYPE M62320FP,I/O EXPANDER 16P SOP TP AT24C02N-10SI-2.7 ATMEL 8P SOIC SN74HCT08D TEXAS INSTRUMENT 16P M62320FP,I/O EXPANDER 16P SOP TP SN74LVTH541PWR 20P TSSOP SN74LVTH541PWR 20P TSSOP KA7805R FAIRCHILD 2P D-PAK THC63LVD103 64P TQFP TRAY 10BIT LVDS TX SC1565IST-1.8 SEMTECH 3P SOT223 TP MIC39100 MICREL 3P SOT223 KA7809R, FAIRCHILD 2P D-PAK BA033FP-E2 ROHM 3P-SOP,TO252-3 PQ05DZ1U SHARP 5, SMD TYPE PQ05DZ1U SHARP 5, SMD TYPE BA033FP-E2 ROHM 3P-SOP,TO252-3 SC1565IST-1.8 SEMTECH 3P SOT223 TP BA033FP-E2 ROHM 3P-SOP,TO252-3 MIC39100 MICREL 3P SOT223 74ACT253SC FAIRCHILD 16P SOIC ST3232CDR SGS-THOMSON SOP16 M52758FP MITSUBISHI 36PIN M74HC123RM13TR SGS-THOMSON 16P SOP M74HC123RM13TR SGS-THOMSON 16P SOP CXA2069Q QFP64 BK I2C BUS AV S/W CXA2101AQ 80P,QFP BK SN74HCT08D TEXAS INSTRUMENT 16P M74HC123RM13TR SGS-THOMSON 16P SOP LGDP4410 LG IC 176P TQFP TRAY IEP SDA6001 QH B12 MICRONAS 128P MQFP KIA7805API 3P TO-220 ST 5V(=KIA7805PI) PQ09RD21 4SIP ST REGULATOR PQ09RD21 4SIP ST REGULATOR PQ12RD21 4SIP ST REGULATOR M62320FP,I/O EXPANDER 16P SOP TP DS1621V 8P SOIC ST THERMOSTAT HY57V641620HGT-H HYNIX 54P TSOPII MX29LV160ATTC-70 MACRONIX 48P TSOP AT24C16AN-10SI-2.7 ATMEL 8P SOIC KIA7027AF 3, SOT-89 TP RESET IC 2.7V VPC3230D C5 80P QFP FLI2300BD GENESIS 208P PQFP HY57V643220C(L)T-6 HYNIX 86P TSOP VPC3230D C5 80P QFP GM1501HBD GENESIS 416P PBGA

TRANSISTORQ100 Q100 Q1000 Q101 Q101 Q102 Q102 Q102 Q103 Q103 Q103 Q104 Q105 Q105 Q106 Q106 Q107 Q107 Q108 Q108 Q109 Q109 Q110 Q110 Q111 Q111 Q112 Q113 Q114 Q1200 Q1201 Q1202 Q1501 Q1503 Q207 Q208 Q209 Q210 Q211 Q214 Q215 Q216 0TR150400BA 0TR830009BA 0TRKE80038A 0TR387500AA 0TR830009BA 0TR387500AA 0TR387500AA 0TR830009BA 0TR150400BA 0TR387500AA 0TR830009BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR830009BA 0TR387500AA 0TR830009BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR830009BA 0TR830009BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR104009AF 0TR387500AA 0TR150400BA 0TR104009AF CHIP 2SA1504S(ASY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR KTC3552T-RTK KEC SOT-23F 50V 3A CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS NON N-CHANNEL S/W TR BSS83 TP PHILIPS NON N-CHANNEL S/W TR CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP KRC104S SOT-23 TP KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP KRC104S SOT-23 TP KEC

- 36 -

For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;

CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic

RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible

LOCA. NO Q217 Q218 Q219 Q300 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q311 Q312 Q313 Q314 Q315 Q316 Q400 Q400 Q401 Q401 Q402 Q402 Q403 Q403 Q404 Q405 Q406 Q800 Q801 Q802

PART NO 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA

DESCRIPTION CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC

LOCA. NO D120 D1200 D1201 D1206 D121 D122 D123 D124 D125 D126 D127 D128 D129 D130 D1300 D1301 D1302 D1303 D1304 D1305 D1306 D131 D1501 D1503 D200 D201 D202 D203 D204 D205 D400 D500 D5001 D501 D502 D503 ZD100 ZD101 ZD102 ZD103 ZD104 ZD105 ZD206 ZD207 ZD208 ZD400 ZD401 ZD800

PART NO 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD184009AA 0DD226239AA 0DD100009AM 0DD226239AA 0DD226239AA 0DD226239AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DZ820009AH

DESCRIPTION CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 KDS184S CHIP 85V 300MA KEC TP CHIP KDS226 SOT-23 EU1ZV(1) TP SANKEN CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A SD05.TC SEMTECH SOD323 5V 5A 15A MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA -

DIODED100 D100 D1000 D1001 D1002 D1003 D1004 D101 D101 D102 D105 D106 D116 D117 D118 D119 0DD226239AA 0DD226239AA 0DD226239AA 0DD184009AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD184009AA 0DD184009AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 KDS184S CHIP 85V 300MA KEC TP CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23

CAPACITORC1001 C1002 0CE107SF6DC 0CE227VF6DC 100UF MVG 16V M SMD 220UF MV 16V 20%(SMD) SMD

- 37 -




LOCA. NO C1004 C1006 C1016 C1017 C1018 C102 C1020 C1022 C1025 C1027 C1031 C1037 C104 C1042 C1045 C105 C1058 C1059 C1060 C1063 C1066 C1067 C107 C1072 C1074 C1078 C1079 C108 C1081 C111 C112 C113 C114 C120 C1202 C1205 C1206 C121 C121 C1211 C1212 C1215 C1216 C1218 C1220 C1223 C1229 C1233 C124 C1249 C1250 C1251

PART NO 0CE475SK6DC 0CE477SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE475SK6DC 0CE107SF6DC 0CE477SF6DC 0CE475SK6DC 0CE107SF6DC 0CE477SF6DC 0CE477SF6DC 0CE476DF618 0CE477SF6DC 0CE107SF6DC 0CE476DF618 0CE107SF6DC 0CE477DJ618 0CE227VF6DC 0CE227VF6DC 0CE107SF6DC 0CE477DJ618 0CE477SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477SF6DC 0CE107SF6DC 0CE475SK6DC 0CE477SF6DC 0CE106SF6DC 0CE475SK6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE477SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE227VF6DC 0CE477SF6DC 0CE227VF6DC 0CE107SF6DC 0CE227VF6DC 0CE477SF6DC 0CE107SF6DC 0CE227VF6DC 0CE227VF6DC 0CE477SF6DC

DESCRIPTION 4.7UF MVG 50V 20% SMD 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 4.7UF MVG 50V 20% SMD 100UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 4.7UF MVG 50V 20% SMD 100UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 47UF STD 16V M FL TP5 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 47UF STD 16V M FL TP5 100UF MVG 16V M SMD 470UF STD 35V 20% FL TP 5 220UF MV 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 100UF MVG 16V M SMD 470UF STD 35V 20% FL TP 5 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 4.7UF MVG 50V 20% SMD 470UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 4.7UF MVG 50V 20% SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 100UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 47UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 100UF MVG 16V M SMD 220UF MV 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 220UF MV 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD


PART NO 0CE227VF6DC 0CE227VF6DC 0CE227VF6DC 0CE227VF6DC 0CE475SK6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE107SF6DC 0CE227VF6DC 0CE227VF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE477SF6DC 0CE476SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE107SF6DC 0CE477SF6DC 0CE477SF6DC 0CE476XFKDC 0CE476XFKDC 0CE106SF6DC 0CE476XFKDC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CE106SF6DC 0CN105EJ56A 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE106SF6DC 0CN105EJ56A 0CE476SF6DC

DESCRIPTION 220UF MV 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 4.7UF MVG 50V 20% SMD 47UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 47UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 220UF MV 16V 20%(SMD) SMD 220UF MV 16V 20%(SMD) SMD 100UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 470UF MVG 16V 20%(SMD) SMD 470UF MVG 16V 20%(SMD) SMD 47UF MVK-BP,CN 16V 20%,-20% SMD TAPPING 47UF MVK-BP,CN 16V 20%,-20% SMD TAPPING 10UF MVG 16V 20%(SMD) SMD 47UF MVK-BP,CN 16V 20%,-20% SMD TAPPING 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 1.0UF 3216 35V 10% X7R 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 1.0UF 3216 35V 10% X7R 47UF MVG 16V M SMD

- 38 -





PART NO 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE227VF6DC 0CE476SF6DC 0CE107SF6DC 0CE227VF6DC 0CE476SF6DC 0CE107SF6DC 0CE105SK6DC 0CE107SF6DC 0CE107SF6DC 0CE106SF6DC 0CE106SF6DC 0CE1074F618 0CE1074F618 0CE227DF618 0CE105CK636 0CE105CK636 0CE105CK636 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE105SK6DC 0CE106SF6DC 0CE476SF6DC 0CE106SF6DC 0CE107SF6DC 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CE106SF6DC 0CE107SF6DC 0CE107SF6DC 0CE226SF6DC 0CE106SF6DC 0CE106SF6DC 0CE226SF6DC 0CE226SF6DC 0CE106SF6DC

DESCRIPTION 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 47UF MVG 16V M SMD 220UF MV 16V 20%(SMD) SMD 47UF MVG 16V M SMD 100UF MVG 16V M SMD 220UF MV 16V 20%(SMD) SMD 47UF MVG 16V M SMD 100UF MVG 16V M SMD 1UF MVG 50V M SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 100UF SRA 16V M FL TP5 100UF SRA 16V M FL TP5 220UF STD 16V M FL TP5 1UF SHL,SD 50V M FM5 BP(D) TP 1UF SHL,SD 50V M FM5 BP(D) TP 1UF SHL,SD 50V M FM5 BP(D) TP 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 1UF MVG 50V M SMD 10UF MVG 16V 20%(SMD) SMD 47UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 100UF MVG 16V M SMD 22UF MVG 16V 20% SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 10UF MVG 16V 20%(SMD) SMD

LOCA. NO C737 C744 C752 C757 C762 C769 C777 C778 C785 C800 C801 C802 C803 C812 C822 C825 C827 C828 C829 C834 C837 C840 C841 C847 C851 C852 C862 C863 C872 C873 C874

PART NO 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE335SK6DC 0CE226SF6DC 0CE226SF6DC 0CE476SF6DC 0CE226VF6DC 0CE226VF6DC 0CE107SF6DC 0CE335SK6DC 0CE107SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CN105EJ56A 0CE108DH618 0CE108DH618 0CF4741L438 0CF4741L438 0CE335SK6DC 0CN105EJ56A 0CE108DH618

DESCRIPTION 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 3.3UF MVG 50V 20% SMD 22UF MVG 16V 20% SMD 22UF MVG 16V 20% SMD 47UF MVG 16V M SMD 22UF MV 16V 20%(SMD) SMD 22UF MV 16V 20%(SMD) SMD 100UF MVG 16V M SMD 3.3UF MVG 50V 20% SMD 100UF MVG 16V M SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 10UF MVG 16V 20%(SMD) SMD 100UF MVG 16V M SMD 1.0UF 3216 35V 10% X7R 1000UF STD 25V M FL TP5 1000UF STD 25V M FL TP5 0.47UF D 63V 5% TP 5 M/PE NI 0.47UF D 63V 5% TP 5 M/PE NI 3.3UF MVG 50V 20% SMD 1.0UF 3216 35V 10% X7R 1000UF STD 25V M FL TP5

COILL1004 L1005 L1006 L1007 L1200 L1203 L1209 L1213 L803 L804 L805 L806 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0024A 6140VB0024A 6140VB0024A 6140VB0024A 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 LPK-1322A SOOJUNG 22UH +-10% LPK-1322A SOOJUNG 22UH +-10% LPK-1322A SOOJUNG 22UH +-10% LPK-1322A SOOJUNG 22UH +-10%

RESISTORAR500 AR501 AR502 AR503 AR504 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5%

- 39 -




LOCA. NO AR505 AR513 AR600 AR600 AR601 AR601 AR602 AR602 AR603 AR603 AR604 AR605 AR606 AR607 AR608 AR609 AR610 AR611 AR612 AR613 AR614 AR615 AR616 AR617 AR618 AR700 AR701 AR701 AR702 AR703 AR707 AR708 AR709 AR710 AR711 AR712 AR713 AR714 AR715 AR717 AR718 AR719 R5026

PART NO 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RD0152H609

DESCRIPTION 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 15 OHM 1/2 W 5.00% TA52

LOCA. NO LD1204 LD1206 LD1207

PART NO 0DL233309AC 0DL233309AC 0DL233309AC

DESCRIPTION SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD

SWITCHSW201 SW202 SW203 SW204 SW205 SW206 SW800 140-315A 140-315A 140-315A 140-315A 140-315A 140-315A 6600VM2006A TACT SKHV17910B LG C&D NON 12V TACT SKHV17910B LG C&D NON 12V TACT SKHV17910B LG C&D NON 12V TACT SKHV17910B LG C&D NON 12V TACT SKHV17910B LG C&D NON 12V TACT SKHV17910B LG C&D NON 12V SDDF3PATP011 250V 4A HORIZONTAL .G

FILTER & CRYSTALL100 L100 L1000 L1002 L1008 L1009 L101 L101 L1010 L1011 L1012 L1013 L1014 L1015 L1016 L1017 L1018 L1019 L102 L102 L102 L103 L103 L103 L104 L104 L105 L105 L106 L107 L108 L1201 L1206 L1207 L1210 L1211 L1216 L1217 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6200JB8010L 6200JB8010L 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM

LEDIC103 IC104 LD1000 LD1001 LD1002 LD1003 LD1203 6301V00003A 6301V00003A 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC UEX-LD-048 WHITE WHITE LED INDEX UEX-LD-048 WHITE WHITE LED INDEX SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD

- 40 -

LOCA. NO L1300 L1302 L1303 L1304 L1305 L1307 L1310 L1311 L1312 L1313 L1314 L1315 L1316 L1317 L1318 L1321 L1322 L1325 L1326 L1327 L1328 L1329 L1330 L1331 L1332 L1333 L1500 L200 L200 L201 L201 L202 L203 L204 L205 L206 L207 L208 L210 L211 L212 L213 L213 L214 L215 L216 L216 L300 L301 L302 L305 L306

PART NO 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6200JB8013L 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6210VC0006A 6200JB8010L 6200JB8010L 6200JB8010L 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0005A 6210VC0005A

DESCRIPTION FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM BEAD FEELUX 60 OHM TB201209U060 FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM BK2125 HS 750 TAIYOYUDEN 2X1.25X0.85MM BK2125 HS 750 TAIYOYUDEN 2X1.25X0.85MM

LOCA. NO L307 L308 L309 L310 L311 L312 L313 L314 L400 L400 L401 L401 L402 L403 L404 L405 L406 L407 L408 L500 L5001 L501 L502 L503 L504 L505 L506 L507 L700 L800 L807 L808 R102 R103 R106 R107 R108 X500 X600 X600 X700 X700 X800

PART NO 6210VC0005A 6210VC0006A 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0005A 6210VC0005A 6210VC0005A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6202VDT002K 6202VDB007B 6202VDT002J 6202VDB007B 6202VDT002B 156-A02M

DESCRIPTION BK2125 HS 750 TAIYOYUDEN 2X1.25X0.85MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM BK2125 HS 750 TAIYOYUDEN 2X1.25X0.85MM BK2125 HS 750 TAIYOYUDEN 2X1.25X0.85MM BK2125 HS 750 TAIYOYUDEN 2X1.25X0.85MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM FBMH3216 HM501NT TAIYOYUDEN 3.2X1.6X1.6MM MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA MLB-201209-1000L-N2 1000OHM 350MA RESONATOR,CRYSTAL SX-1 6MHZ RESONATOR,CRYSTAL HC49U20.250MHZ RESONATOR,CRYSTAL SX-1 13.500000MHZ RESONATOR,CRYSTAL HC49U 20.250MHZ RESONATOR,CRYSTAL SX-1 SC14.3MHZ RESONATOR,CRYSTAL HC49U 18.432MHZ

JACKJK103 JK200 JK201 JK202 JK300 P101 P102 6613V00026A 6612M00009A 6612M00009A 6612M00009A 6612J00057A 380-068E 6612BBBHN6A UJB-03-28A UGCOM UJB-R1-033 UGCOM 21P UJB-R1-033 UGCOM 21P UJB-R1-033 UGCOM 21P UJB-08-01A UGCOM 8P RCA+1P UEJ-CV-018 UGCOM D3.5 E/P 440062-1 AMP DVI INTERACED RIGHT ANGLE

- 41 -

LOCA. NO P201

PART NO 380-068E

DESCRIPTION UEJ-CV-018 UGCOM D3.5 E/P

LOCA. NO

PART NO

DESCRIPTION

ACCESSORIESA1 A2 A3 A4 A5 A6 A7 3828VA0509F 6710V00116W 6410VEH003C 6850J00004A 6850VA0004J 6851V00019A 4810V00509B MANUAL,OWNERS 116W TX 026H REMOTE CONTROLLER, AF045A RZ-50PY10 POWER CORD, M2511A-001 2800MM CABLE,DVI LVDS UL20276 AWG30 500MM CABLE,COAXIAL UL1365#26 150MM UCA-EX-069 CABLE ASSEMBLY, 4AC208A0 3M CORE 2EA BRACKET, WALL AP-60DA10

MISCELLANEOUSP100 P200 S1 TU100 TU101 6630VGA001C 6630VGA004B 6851V00022C 6700MF0010A 6700MF0010B CONNECTOR (CIRC),D-SUB 68114-1521 CONNECTOR (CIRC),D-SUB 69107-0921 CABLE,COAXIAL UL1365#26 VW-1 TUNER, TAUM-W501P MINI 4 SYSTEM MAIN TUNER, TAFM-W502P MINI 4SYSTEM SUB

- 42 -

PRINTED CIRCUIT BOARDMAIN (TOP) MAIN (BOTTOM ) POWER S/W(TOP) POWER S/W(BOTTOM)

SIDE A/V(TOP)

SIDE A/V(BOTTOM)

CONTROL(TOP)

CONTROL(BOTTOM)

TUNER(TOP)

TUNER(BOTTOM) FAN CONTROL(TOP)

FAN CONTROL(BOTTOM)

INDEX(TOP)

INDEX(BOTTOM)

P/NO : 3828VD0161F

Aug., 2004 Printed in Korea

Lg Plasma Rz-60py10

Documents