Transcript
1
MySpot 200Installation Procedure (Concrete)
19JULY2007
2
Locating the MySpot 200The unit is placed so that,
when the car is parked the barrier is ahead of the
rear wheels but does not interfere with
the access to the front doors.
3
Install in Middle
Only install the unit in the middle of the space
4
Space Requirements
Surface must be flat No standing water No high points
5
Inspect the CartonA: PowerPod (includes the
electronics and the mechanism)
B: IdlePod
C: Barrier
D: (2) remote controls
E: Parts kit
F: Drilling Template
6
Where to Place the Unit
Place the template “TT” as shown
7
Direction of Template
The template must be perpendicular to the edge of the parking space
Note the direction of the arrow on the template
8
Drill Pilot Holes
Use a small (6mm, ¼”) drill to mark the 7 holes by drilling through the template into the surface
Do not drill directly with the larger drill
Remove template Verify that all 7 holes are
clearly visible
9
Concrete or Asphalt?
The procedure is different for concrete and for asphalt surfaces.
If the surface is asphalt, close this manual and select the “Asphalt installation” manual
10
Concrete Anchors 7 anchors are included Each includes a special M6
bolt and washer They require a 65mm hole
depth They require a hole
diameter of 10mm (3/8”)
11
Concrete: Drill 7 holes
Use a 10mm (3/8”) masonry drill
Drill precisely where the 7 small holes were marked
Drill to a depth of 65mm (2.5”) or more
Blow holes clean when done
12
Insert Anchors
Push anchors into holes until the head is flush with ground
Use M6 wrench to tighten Allen bolt moderately
Do not remove bolts yet
13
Clean Surface
Broom sweep area
14
Remove Screws
Removed the bolts and washers from the 7 anchors
15
Separate Plates from Pods
Remove 4 security bolts from PowerPod
Remove 2 security bolts from IdlePod
Separate the pods from the plates
16
Attach Plates
Use large washers and bolts from anchors (7 sets)
Secure plates to ground Do not tighten yet
17
Check alignment Bend or cut template as
shown Place template between
plates Adjust plates until aligned
parallel to edges of template
Verify that there is less than 4mm (1/8”) gap between template and plates
18
Tighten Screws
Once the alignment has been confirmed, tighten the 7 bolts of the anchors
If any bolt will not tighten (anchor slips), remove anchor, use some filler and reapply anchor
It is essential that all 7 anchors share the load
19
Attach PowerPod Use the 4 security bolts
and washers that came with the IdlePod assembly to secure the pod to the plate
If the wrong bolts are used (too long), they will push the plates out of the ground
Tighten the 4 bolts securely
20
Disassemble IdlePod
The IdlePod needs to be attached to its plate using 3 bolts
To access the 3rd bolt, the cover needs to be removed
Use the security wrench to remove the 3 bolts
21
Remove Cover
Lift the cover of the IdlePod
Lift the shaft The 3rd hole may be
protected by a plastic insert
Remove the insert by pushing it from the top
22
Prepare IdlePod Plate
Place 2 adaptors over the 2 outside holes in the plate
If these adaptors are not in your kit, proceed without them
23
Attach IdlePod Use security bolt, star
washer and flat washer to attach the 2 outside ears of the pod to the plate
Use a black Allen bolt with star washer and flat washer for the middle attachment point
Make sure all bolts are the proper length; bolts that are too long will push the plate off the ground
Tighten all 3 bolts
24
Place Shaft in IdlePod Place the shaft back so
that the slot fits over the bar in the base
The cowling on the shaft must be free to fall forward (towards the entrance to the space)
If it is not, rotate the shaft 180 degrees before placing it on the base
25
Close Cover of IdlePod Place the cover over the
IdlePod Make sure it is seated
correctly Secure in place using 3
security bolts with star washers
26
WARNING Failure to use the
internal bolt for mounting the IdlePod to the plate will cause the IdlePod ears to break off and void the warranty
27
Install the Barrier Slide the barrier over the
cowlings of the 2 pods as shown
The barrier should be kept parallel to the ground as it is being installed
Only minimal force is required
If excessive force is required, check the alignment of the pods
28
Secure the Barrier
Use the 4 short security bolts and star washers
Tighten securely using the special wrench in the kit
29
Ready for Test
The installation is now complete. The next steps cover the test procedure
30
The Remotes
2 Remote controls are included in the kit
Each remote can control up to 9 separate barriers
The barrier in the kit was factory programmed to accept the #2 button on each of the 2 remotes
31
Terminology
Please study the sketch on the right
Shown are 4 states of the barrier
32
Locked Up State This is the normal
“blocking” state Applying moderate force
to the barrier in either direction will not move the barrier
However, if the force exceeds 30 Kg (65 lbs), the barrier will yield
When the excessive force is removed, the barrier will return to the Locked Up state.
Barrier Does not Respond If the barrier does not
respond when removed from the carton..
And it is in the Locked Down state..
Use the Emergency key To release the barrier A. Remove the security bolt
and washer B. Use the 6mm Allen wrench
and rotate the internal bolt counter clockwise
33
34
UnLocked State Press the #2 button on
the Remote. The barrier will fall Its new position is the Un
Locked state In this state, the barrier can be raised
by hand with no resistance If raised all the way, it will lock in the
Locked Up position If the barrier was previously manually
raised, when the command drops the barrier to the UnLocked state, the internal motor can be heard running an extra cycle. This is normal
35
Locked Down State When a wheel of the car
drives over the barrier, the barrier is pushed to the ground
That is the Overtravel state
When the wheel leaves the barrier, the barrier returns to the Locked Down state
The only way to exit the locked down state is via a remote command
36
Testing, continued If the barrier is in the
Unlocked state… …Step on the barrier You need to apply 100 Kg
(220 lbs) to force the barrier to the ground
Jump if your weight is less than that…
The barrier will hit the ground
When you step off, it will rise somewhat to the Locked Down state
37
Testing, Last Step Step on the barrier a
second time The barrier needs to be
driven on twice, like a car getting in and out, to prevent accidental raising of the barrier under a parked car
Push the #2 button on the remote
The barrier will rise to the Locked Up position
38
Troubleshooting
If you run into a problem when testing the unit
Look up the troubleshooting chart
The chart is printed at the end of the installation manual
Or it is available on the web site
39
Thank You
Please do not hesitate to contact our hotline+1 973 669 8214 ext 1 during business hours09:00 to 17:00 Eastern Standard Time (GMT -5:00)
top related