UNDERSTAND THE NATURE AND BRACE PURPOSE
UNDERSTAND NATURE SIGNAL AUDIOBy Sarbini, S.Pd (SMK Muhammadiyah 3 Yogyakarta)
Teknologi dan Rekayasa
A. AMPLIFIER
Amplifier or power amplifier function amplify the audio signal and then follow to the loudspeaker
POWER AMPLIFIER
Power Amplifier tata panggung
Teknologi dan Rekayasa
Fidelitas and Efficiency
Fidelity means that the similar form of the output signal of a replica of the original input signal.
Brace system is said to have fidelitas high (high fidelity), if the system is able to produce the output signal of exactly the same as the input signal.
Teknologi dan Rekayasa
Efficiency: comparison of power output than the input power.
Brace system said to have high levels of efficiency (100%) if there is no loss-loss in the process amplify / no power be heat.
Teknologi dan Rekayasa
B. AMPLY VARIOUS
1.Class A Characteristics:
Signal output work on active areas. Fidelitas high Form of signal keluarannya match the input
Low efficiency (25% - 50%). Transistor is always ON, so most of the power
source portion terbuang heat. Transistor class A brace plus the necessary extra
cooling (such as a larger heatsinks).
Teknologi dan Rekayasa
Kurva amply class A
Teknologi dan Rekayasa
2. CLASS B
Characteristics :
Phuspull / Transistors work alternately between the transistors Q1 (NPN) and Q2 (PNP).
Heat generated is not too large
Greater efficiency (75%)
There is a cross-disability (cross over)
Power supply voltage +, _ and Ground
Teknologi dan Rekayasa
Curve amply class B
Teknologi dan Rekayasa
Series amply class B
Teknologi dan Rekayasa
3. CLASS AB
Characteristics :
Phuspull / transistors work alternately between the transistors Q1 (NPN) and Q2 (PNP).
Heat generated is not too large
Greater efficiency (50% s / d 75%)
Disability does not occur cross (cross over)
Fidelitas Highest
There was a signal on my second transistornya actively at the time of transition (gumming).
Power supply voltage +, _ and Ground
Teknologi dan Rekayasa
Series brace Class AB OVERLAPPING OUTPUT PENGUAT KELAS AB
Teknologi dan Rekayasa
4. CLASS C
Characteristics :
Transistors only need one work only on the active phase positive High efficiency (100%) Fidelitas lower than class AB Often used in a series of transmitter oscillator Working in the area of active / linear
Teknologi dan Rekayasa
Series brace Class C
Teknologi dan Rekayasa
5. CLASS D Characteristics
Using the PWM technique Pulsa Width Modulation) where the width of the balance is proportional to the input signal amplitudo.
Teknologi dan Rekayasa
Illustrated amply PWM modulation class D
Teknologi dan Rekayasa
Working as a switching transistor
Using sampling techniques
require a triangular wave generator and comparator to produce a signal proportional to the PWM signal input amplitudo.
Raising fidelitas required to filter Brace is often used in digital 1 bit (on or off).
Teknologi dan Rekayasa
6. CLASS E
Characteristics: Brace similar to the class C
Require a series of LC with a working transistor less than half a duty cycle
Working as a switching transistor
Usually require the type of FET transistors
Teknologi dan Rekayasa
Efficient and suitable for applications that require large drive currents, but with the input current is very small.
Disipasi small heat
Usually applied to the transmission equipment such as mobile phone
Teknologi dan Rekayasa
7. CLASS T
Characteristics :
Also called digital brace
Using the concept of modulation PWM switching transistor and the filter
The process is a manipulation of the previous bit-bit digital. In a processor with the audio feedback process that is also a digital correction for time delay and phase.
Teknologi dan Rekayasa
8. CLASS G
Characteristics :
Including analog brace to improve the efficiency of the brace class B / AB
Supply Voltage made step because requires a high voltage
Teknologi dan Rekayasa
Brace the concept of class G with a supply voltage multilevel
Teknologi dan Rekayasa
9. CLASS H
Characteristics :
Including analog brace to improve the efficiency of the brace class B / AB
Brace similar to the G-class supply voltage that can be changed as needed
Complex but efficient
High-low voltage supply is designed to be more limited linier not only have 2 or 3 phase only
Supply voltage and the voltage output is only a few more high-volt