••
TRIUMPH TR4WORKSHOP MANUAL
PART NUMBER 510322
Issued by the
SERVICE DIVISION
STANDARD-TRIUMPH SALES LIMITEDA member of the Leyland Motors Group
COVENTRY ENGLAND
Cut-away view of the Triumph TR4
INTRODUCTION
This Workshop Manual. which is in loose-leaf form, has been compiled to assist Standard~Triu111ph
Distributors and Dealers throughout the world in the efficient repair and maintenance of Triumph TR4models from Commission Number (Chassis Number) CT. 1.
The information most frequently required is given in the preliminary pages and includes :-thcIntroduction, General Specification, Unit reference numbers, Vehicle dimensions, Nut lightening torques,Special tools, Recommended lubricants, Jacking system and a short glossary of part names and alternatives.
Whilst retaining the same grouping system used for Service Information Sheets and previous WorkshopManuals, this book, the first of a new series, introd uces an additional group having the designation"'0". This describes the position and function of the instruments and controls. Recommendationsare also given for "'running in", together with detailed working instructions for carrying out the "CustomerPreparation Service", periodical lubrication, and regular maintenance operations listed on the back ofvouchers contained in the Maintenance Voucher Booklet accompanying each ne\v vehicle. A lubricationchart is provided at the end of the section.
Dismantling, assembly and adjustment procedures for the complete vehicle are divided into six groupsnumbered one to six. Each deals with one major unit and associated parts, except group six, which dealsexclusively with the electrical system. Each group is preceded by a detailed specification and dimensions.
Special ToolsThe use of special tools mentioned in the text, contributes to an efficient and profitable repair. Some
operations are, in fact. impracticable without their use, particularly those, for example, which deal v·/ith theassembly of the differential unit. Distributors are therefore urged to check their tools and order thosenecessary.
Numbering Pages and SectionThe running headline, at the top of the page, names each section \vithin a group. For example. group
one contains four sections, namely: Engine, Cooling, Fuel and Exhaust Systems, these being numbered1 to 4 respectively.
The group number is shown at the top outer edge of each page and is folhnved by a decimal point.
Each section number is placed after the decimal point following the group number.
Two numerals placed after the section number are used to identify the pages which comprise a particularsection, thus page 5 of the cooling section would appear J ,205.
Service Information and Amendment ProcedureDesign modifications, changes in procedure and notice of amendment subsequent to the preparation
of this manual are given in Service Information Sheets which are issued regularly to all authorised dealers.Should existing instructions be affected or additional information be v/arranted, new pages \vill be includedwith each consecutively numbered notice of amendment. This \vill also give details of the pages and grollJ.'l$affected. See page 21.
To ensure that this manual is kept up to date, Distributors and Dealers are advised to \\Tire theamendment number, the page number and the group number in the space provided on the page precedingG:'oup "0" as the amended pages of text are inserted. Any gaps in the sequence of amendment numberswill then be readily apparent and immediate action can be taken to obtain the missing sheets.
Schedule of Repair OperationsThe operations listed in the "'Schedule of Repair Operation Times" refer to those described in this
manual. The time set against each operation in the schedule is evolved by performing the actual operationson a standard vehicle using special tools where stated. The "'Schedule of Repair Operation Times", foruse \vith this manual, is issued as a separate publication and ma~l be obtained from the Spares Divisionunder Part Number 511225.
Page 5
GENERAL SPEClFIC\TlON
86 mOl.83 mm.92 mm.232 sq. em.216 sq. em.2138 C.e.1991 c.c.
EngineNumber of cylindersBore of cylinders
(Special Order)Stroke of crankshaftPiston area
(Special Order)Cubic capacity
(Special Order)Compression ratioValve rocker clearances~inlet and exhaustValve timing with valve rocker clearances set at
0·0165' (0,42 mm.)
4}-386"3·268:3 '622~'
36·0 sq. in.33·5 sq. m.130·5 cu. in.121·5 cu. in.9 I0·010" (cold) 0'254 mm.Inlet and exhaust valves to be equally open at T.D.C onthe exhaust stroke.
Performance Data (Engine)Nett ..
(Special Order)
Piston speed at 100 m.p.h. (top gear) "
100 B.H.P. at 4,600 r.p.m.Torque 1,520 Ib in. at 3,350 r.p.m.(Equivalent to 147 1b/sq. in. B.M.E.P.).100 B.H.P. at 5,000 r.p.m.Torque 1,410 Ib in. at 3,000 r.p.m.(Equivalent to 145 Ib/sq. in. B.M.E.P.).2,850 ft/min. at 4,800 r.p.m. (3'7 : I axle).
Lubrication (Engine)Type of pumpOil filter
Release pressure
Hobourn-Eaton eccentric rotOLPurolator ; A.C. Delco; Tecalemit full flow (replaceableelement).70 Ib/sq. in. 4'921 kg/sq. em.
setting).
0·4 mOl.
(Normal road use).(High speed touring).(Competition use).(Low octane fuel).
0·64 mm.
0'015"Lodge CNY
HN2HNCN
0'025"I : 3 : 4 : 2.4' B.T.D.C. (Basic
Gap
Ignition SystemContact breaker gapSpark plugs~Type
Firing orderIgnition timing
Cooling SystemCirculationWater pump typeTemperature control
Radiator
Filler cap-- pressure
Pump.Impeller - incorporating by~pass.
Thermostat.Opening temperature. 70°C (l58°F)Fully open at 85°C (J85°F)Pressurised-finned vertical flat tubes--extended headertank.A.C type.4 lb/sq. in. 0·28 kg/sq. em.
Fuel SystemFuel tankCarburettors
Air cleaners.Fuel pump ~ type
~- operating pressure.
Non-pressure type mounted over rear axle.Twin S.U. H6.Needle size - SM.Wire gauze type.A.C. mechanical with filter and sediment bowlJ i - 2i Ib.,/sq. in.
ClutchTypeOperationAdjustment
Borg & Beck 9"' single dry plate.Hydraulic.Push rod at slave cylinder.
GearboxType . . · . · . ·. · . ·. ·. 4 forward speeds and reverse. Synchromesh on all
forward gears.Control ·. · . · . ·. · . · . Centre floor~mounted remote controL
Rear AxleType . . · . · . · . · . · . · . Hypoid bevel gears; semi-floating axle shafts.
Tapered roller bearings.Ratio .. 3·7 or 4·1 :l.
,.. · . ·. · . ·. · .
Gear Ratios
Overdrive Overdrive OverdriveTop Top 3rd 3rd 2nd 2nd ~ Rev.
Gearbox Ratios · . 0·82 1·0 1·09 1·325 1·65 2·01 3·139 3·223
3·7 : 1 Axle
Overall Ratios · . 3·034 , 3-7 , 4·02 , 4·9 6·1 7-44 11·61 11·93
4·1 : 1 Axle
Overall Ratios ·., 3·36 , 4·1 4·46 5·44 6·76 8·24 , 12·87 , 13·21
BrakesSystem .. .. .. .. . . . . Girting hydraulic.
Front - Caliper disc.Rear - Drum (leading and trailing shoes).
Adjustment · . . . .. .. .. .. Rear brakes only (I adjuster each wheel).Dimensions .. .. .. .. .. .. Rear shoes : 9" x Ii" (22,86 x 4·45 em.).
TYRE PRESSURE DATATYRE PRESSURES
Goodyear Goodyear Goodyear GoodyearAllweather Rib Allweather Rib Motorway D.F.S.
and Dunlop Nylon and Special and (165-380)Gold Seal Dunlop Gold Dunlop Road and Michelin
Seal Nylon Speed R.S.5 (165/15X)OPERATING CONDITIONS
5'5015'90-15 5'50/5'90-15 5'50/5'90-15 (165/l5X)
Lbs. per sq. in. Lbs. per sq. in. Lbs. per sq. in. Lbs. per sq. in.---
Normal motoring with sustained Front Rear Front Rear Front Rear Front Rear
Ispeeds limited to 85 m.p.h.
20 24 20 24 20 24 24 32
I ---Fast motoring on Motorways andsimilar roads with sustained speeds 26 30 20 24 20 24 24 32up to 100 m.p.h.
---_ ..- ---High speed tuning with speeds Notregularly in excess of 100 m.p.h. recommended 26 30 20 24 24 32
Page 7
SuspensionFront
Rear ..
SteeringTypeCaster angleCamber angleKing pin inclinationFront wheel alignment
Turning circle
Independent suspension with wishbones top and bottom.Patented bottom bush and top ball joint swivels. Coilsprings controlled by telescopic dampers. Taper rollerhub bearings.Wide semi-elliptic springs, controlled by piston typedampers.
Rack and pinion unit. Telescopic steering column.3"2(, Static laden.7'~
Parallel to r (3·18 mm.) toe-in.Parallel to w" (1·59 mm.) toe-in if fitted with GoodyearD.ES. or Michelin X tyres.33' 0- 10 metres.
"
Chassis DataWheelbaseTrack: Front (Disc wheels)
Rear (Disc wheels)Front (Wire wheels)Rear (Wire wheels)
Ground clearance (Static laden) ..
Exterior DimensionsOverall length
widthheight
WeightDry (excluding extra equipment)Complete (including fuel, oil, water and tools)
CapacitiesEngine ~ from dry
Drain and refillGearbox
With overdrive from dryDrain and refill
Rear axleWater capacity of cooling system
With heater fittedFuel capacity
Electrical SystemBatteryControl boxGenerator
Page 8
7' 44' I"4' 0"4' 2"4' I'
6-
12' 104' 9V4' 2-
2128 lb.2240 lb.
Imperial11 pints10 pintsI! pints3:\ pints2t pintsI! pints13 pints14 pints
III galls.
12 volt. 51 amps. hr.Model RB.l06-2.Model C40-L
2,236 metres.1'245 metres.I '220 metres.I ·270 metres.1'245 metres.15·24 em.
391 em.146 em.127 em.
965 kg.1015 kg.
U.S.13·2 pints12 pints1,8 pints4·2 pints3'3 pints1·8 pints
15·7 pints16·8 pints14 galls.
Metric6·25 litres5·7 litres0·8 litres2·0 litres1,6 litres0·8 litres7 ·39 litres8·0 Htres
53·5 litres
LOCATION OF COMMISSION ANDUNIT NUMBERS
The Body Number is located on the R.H. side ofthe Scuttle PaneL
The Commission Number (Chassis Number) islocated on the Scuttle Panel adjacent to the windscreenwiper motor and may be seen by lifting the bonnet.
The Engine Serial Number is stamped on the L.H.side of the Cylinder Block.
The Gearbox Serial Number is stamped on theL.H. side of the Clutch Housing.
The Rear Axle Serial Number is stamped on theface of the Hypoid Housing Flange.
IMPORTANT
In all communications relating to Service or Spares,please quote the Commission Number(Chassis Number),
Page 9
VEHICLE DIMENSIONS
~.<"'~' ~~v='C: ~v
Page 10
r-
:F I CI59~
::: , ~ .~~-
VEHICLE DIMENSIONS
inches centimetres
A .. , 25·5 66·77B ... .., 88·0 223·52C 154·0 39H6D 5·5 13·97 -<... ... '"Il 6·5 16·51 ;I:
F 20·0 52·07 i'i... t"G (min.) 14·0 35·56 '"-- .... , .. " .'--'---'--~--~ ,",'.'"., ------~- --" -- -~-_ .._~- - (max.) 21·5 54·61 0H (min.) 36·5 92·71 -~(max.) 44·0 Ill·76 '"J 35·0 88·90 Z
VJK 2·0 5·08 -... .., 0L .. , 40·5 102·87 Z
VJM ... 50·I3 127·32N ... 57·25 145·37P .. , 49·75 126·37Q ... .., 60·0 152·40R ... 25·0 63·5S .. , 50·0 127·00
OPERATION
NUT TIGHTENING TORQUES
DESCRIPTION SPECIFIED TORQVESIbs. ft. Kgm.
ENGINECylinder HeadConnecting Rod Caps ..Clutch AttachmentCamshaft Bearing to Block FrontCamshaft Bearing to Block RearDynamo Bracket to BlockDynamo to Bracket and PedestalDistributor MountingDynamo Adjusting Link to Water Pump Body
End Plate Attachment ..Engine Plate and Timing Cover FrontFlywheel Attachment to Crankshaft ..Fan Attachment ..Manifold AttachmentManifold Inlet and ExhaustMain Bearing CapsOil Pump Attachment ..Oil Seal Attachment (Rear)Oil Filter Attachment
Oil Gallery Plugs
Petrol Pump AttachmentPulley to Water Pump Spindle ..
Pulley and Extension to Hub ..Rocker CoverRocker Pedestal ..Sump AttachmentStarter Motor (Attachment)Timing CoverTiming Chain Wheel to CamshaftThermostat Assembly to Cylinder HeadThermostat HousingWater Pump AttachmentWater Pump BodyFlywheel Ring Gear Attachment
GEARBOXExtension to Gearbox ..
Gearbox to Engine AttachmentSelector Fork AttachmentFront Cover to GearboxPropeller Shaft Flange to MainshaftTop Cover to Gearbox ..
Mounting Rear to Gearbox Extension
REAR AXLEBearing Caps to HousingBacking Plate AttachmentCrown Wheel to Differential CaseHypoid Pinion Flange ..Hub to Axle ShaftRear Cover Attachment
Page 12
!" V.N.F. & B.N.C StudI,." V.N.F. Boltf:;'" >:: 18 V.N.C. Setscrewil;'" N.C. SetscrewII;'" V,N.F. SetscrewJi" x 18 D.N.C SetscrewJi" x 24 V.N.F. Bolt," N.F. & N.C Studf,' D.N.C Boltf,' V.N.C Setscrewf," x 18 D.N.C BoltJi' N.F. & D.N.C StudI' x 24 N.F. Setscrew1~' D.N.F. Boltr N.C StudJi' x 24 D.N.F. Studr D.N.C Setscrewfo' N.F. & N.C Studr x 20 D.N.C. Setscrewf," D.N.C Bolts1~" N.F. & N.C Stud*' x 14 V.N.C Setscrewr x 16 D.N.C Setscrew1~' N.F. & N.C Studf,' 24 D.N.F. Simmonds
Nyloc Nutr D.N.F. BoltJi" N.F. & N.C Studr D.N.F. & D.N.C Stud1'k" x 18 V.N.F. Setscrewr x 24 N.F. Boltf," x 18 & 24 N.C Setscrew-{k" x J8N,C. Setscrewtil" x 24 V.N.C. BoltsJi'D.N.F.r x 16 D.N.C Boltsr N.F. & N.C Studf,' D.N.F. x 1·25" Bolt
~"," x 18 V.N.C BoltiGor" x 18 V.N.C. Setscrewf,' N.F. & N.C Setscrew111" V.N.F. Taper Setscrew-e,;-" x 18 N.C. Setscrewr x 16 N.F. Slotted NutJi' N.C SetscrewA" D.N.C Boltr x 20 D.N.F. Bolt
i" x 24 Setscrewr x 24 Setscrewr x 24 D.N.F.V x 18 D.N.F.l" x 18 U.N.F. Nut Slottedri; H '< 24 V,N. F. Setscrew
100 - 10555 - 60
2016 - 1812 - 1416 - 1816 - 188 - 10
16 - 18
14 - 1612 - 1442 - 4616 - 1822 - 2412 - 1485 - 9012 - 148 - 10
22 - 24
32 - 3624 - 2612 - 14
16 - 188 - 10
224 - 2618 - 2026 - 2814 - 1624 - 2616 - 1812 - 1426 - 2826 - 2816 - 18
14 - 1614 - 168 - 108 - 10
14 - 1680 - 12014 - 1614 - 1650 - 55
34 - 3626 - 2835 - 4085 - 100
125 - 14516 - 18
13'826" 14'5207,604" 8·293
2'7652·212 - 2·489I '659 - 1·9362'212 - 2'4892·212 - 2·4891,106- 1·3832-212 - 2-489
1·936 - 2·212I ·659 - 1·9365·807 - 6·3602·212 - 2·4893·042- 3·3181·659 - 1·936
11·752 -12·4431·659 - 1·9361-106 - 1·3833'042- 3·318
4·424 - 4·9773·318 - 3·5951·659 - 1·936
2·212 - 2-4891·106- 1·383
0·2763·318 - 3'5952'489 - 2·7653·595 - 3·8711·936 - 2·2123·318 - 3·5952'212 - 2·4891·659 - I '9363·595- 3·8713·595 - 3·8712'212 - 2·489
1·936 - 2·2121,936- 2·2121,106- 1·3831'106- 1·3831·936 - 2-212
11·060 - 16'5901·936- 2·2121'936 - 2·2126·913 - 7·604
4·701 - 4·9773,595- 3·8714·839 - 5·530
11·752 - 13·82617,282-20'0472·212 - 2·489
OPERATION
NUT TIGHTENING TORQUES-eonlinued
DESCRIPTION SPECIFIED TORQVESIbs. ft. Kgm.
FRONT SUSPENSIONBack Plate and Tie Rod Levers to Vertical Link ~ " 24 U.N.F. Setscrew andii
Bolts 24·26 3-318 - 3·595Ball Pin to Vertical Link !- 20 V.N.F. Nut Slotted 55 - 65 7·604 - 8·987Front Hub to Stub Axle !" x 20 V.N.F. Nut Slotted See group 4Lower Fulcrum Bracket to Chassis i';r" x 24 U.N.F. Setscrew 16 - 18 2·212 - 2-489Stub Axle to Vertical Link r x 20 V.N.F. Stub Axle
Thread 55 - 60 7·604 - 8·295Lower Wishbone to Fulcrum Pin t, - >: 20 V.N.F. Nyloc Nut 26·28 3·595· 3·871Spring Pad to Wishbone r x 24 V.N.F. Stud
r x 24 V.N.F. Bolt 26 - 28 3·595- 3-871Top Wishbone to Fulcrum Pin '" - x 20 V.N.F. Nut Slotted 26·40 3·595· 5·530Top Inner Fulcrum Pin to Chassis r x 24 V.N.F. Bolt
!" x 24 V.N.F. Setscrew 26·28 3 ·595· 3·871Outer Tie Rod to Levers it" x 24 V.N.F. Simmonds
Nyloc Nut 26·28 3·595- 3-871Lower Wishbones to Vertical Link Trunnion . . "'- V.N.F. Slotted Nut See group 4Hub Extension Studs for Wire Wheel Attachment 1~-" N.F. Stud 65 8·987Brake Disc Attachment !" N.F. Bolt 32 - 35 4-424 - 4·839Caliper Attachment '" - N.F. Bolt 50 - 55 6·913 - 7-604Brake Pad Retaining Plate Bolts r N.F. Bolt 5 - 6 0·691 - 0·830
REAR SUSPENSIONRear Road Spring r Centre Bolt 30 - 35 4·148 - 4·839Road Spring to Rear Axle r x 24 V.N.F. Clip Nyloc Nut 28 - 30 3-871 - 4·148Shock Absorber to Frame Bracket r x 24 V.N.F. Setscrew
r x 24 V.N.F. Nyloc 26 - 28 3·595 - 3-871Spring Shackle (Nut to Pin) r x 24 V.N.F. Nut Shackle Pin 26 - 28 3·595· 3·871Spring Front End to Frame V x 20 U.N.F. Bolt 28·30 3·871 - 4·148
CHASSISGearbox Mounting to Crossmember ~"U.N.F. Studs 35 - 40 4·839 - 4·530Gearbox Mounting Crossmember to Chassis .. r V.N.F. x r Bolts 26·28 3·595 - 3·871Body Mounting Extension to Chassis .. i\" V.N.F. x r Bolts 18 - 20 2·489- 2·765Front Cross Tube to Suspension Turrets i" U.N.F. x r Bolts 26 - 28 3·595 - 3-871
STEERING UNITSteering Unit to Chassis 1,- N.F. 'V' Bolts 12 - 14 1·659 - 1·936Steering Column Coupling ~I,' N.F. Bolts 12 - 14 1·659 - j·936Adaptor Column Coupling Unit r N.F. Bolt 6 - 8 ·8295 - I ·106
BODY COMPONENTSSeat to Runner Attachment !- V.N.F. 5 - 6 ·6913 - ·8295
MISCELLANEOUSWheel Studs and Nuts l," U.N.F. 45 - 55 6·221 - 7·604
Pa2e 13
SPECIAL TOOLS
DesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableDesirableEssentialEssentialEssentialDesirableDesirableDesirableDesirableDesirableDesirableEssentialEssentialDesirableDesirableDesirableDesirable
Cylinder Sleeve RetainersValve Guide Remover and Replacer (Main Tool)Valve Guide Remover and Replacer (Adaptors)Valve Seat Insert CutterValve Seat Insert Cutter (Adaptors) ..Valve Seat Insert Cutter (Adaptors) ..Valve Seat Cutter HandlePilotPilotCutter 45'-', H" dia.Cutter 45 -, I JV dia.Cutter IS', n- dia.Cutter 15", 11.' dia.Cutter 75', Ii" dia.Cutter 75 \ I 1. - dia.Valve Spring CompressorValve Spring Compressor (Adaptor)Connecting Rod Aligning JigMaster Multi-purpose Connecting Rod ArborArbor Adaptor (2'2325')Bending BarWater Pump Impeller Remover and Replacer (Adaptors)Universal Pulley PullerSmall End Bush Remover and ReplacerAdjustable Small End Bush Reaming FixtureSet of Reamers . .Camshaft Bushes Remover and Replacer (Main Tool)Camshaft Bushes Remover and Replacer (Adaptors)Oil Seal Driver HandleFuel Pump WrenchSpark Plug WrenchStud Extractor
The following special tools. recommended for the efficient servicing of Standard-Triumph vehicles, should beordered direct from Messrs. V. L. Churchill and Company Limited, Great South West Road, Bedfont, Fcltham.Middlesex, England.
Engine ToolsS.13860AS.60A-26056MFS.6056-1MFS.6056-2316,X316-10316-12317-22317-25317.T-22317.T-25317.P-22317.P-25611861 I8-1335336S.336-230AMFS.J27631220SM. FT.62016200A20SM. FT.6200B32S.32-15504316F20SM.99450
Clutch and Gearbox Tools99A20S.72S,422 IA20SM.9020S.634235S,4235A-220SM.6920SM,4620SM.76S,4221-320SM.73A20SM,477065S.314S,422IA-15
Clutch Assembly FixtureClutch Plate CentraliserMulti-purpose Hand PressPropeller Shaft Flange HolderGearbox Extension Remover . .Axle Shaft Remover (Main Tool)Constant Pinion Shaft Remover (Adaptor) ..Mainshaft Circlip RemoverCirclip InstallerGearbox Countershaft Assembly PilotConstant Pinion Bearing Removing and Replacing AdaptorsGearbox Front Cover Oil Seal DriverGearbox Front Oil Seal Installer2-way Circlip PliersMainshaft Ball Bearing ReplacerMainshaft Ball Race Remover
EssentialDesirableEssentialDesirableDesirableEssentialEssentialDesirableDesirableDesirableDesirableDesirableDesirableDesirableEssentialEssential
Page 14
Overdrive ToolsL.188L.176A7657UnA
L.178L.l79L.181L.182L.183Ll84L.185AU80Ll86Ll87L.190A
Rear Axle ToolsM.86AS.4235A-3S.4221-220S.92SJOIS.l03TS.IM.lOOAM.8420SM.9820SM.90
Hydraulic Test EquipmentDrive Shaft Oil Seal Remover (Adaptor)Mainshaft Oil Seal Remover ..Drive Shaft Oil Seal Replacer Cone Clutch and Spring Thrust Housing
Dismantling ToolFreewheel Assembly RingPiston Ring Fitting Tool, It" dia.Accumulator "'0" Ring ReplacerAccumulator Piston Housing RemoverPump Barrel RemoverPump Barrel Replacer ..Dummy Drive ShaftPiston Ring Fitting Tool, I i-" dia.Mainshaft Bearing Replacer ..Annulus and Tail Shaft Bearing Remover and ReplacerTail Shaft End Float Gauge ..
Hub Remover ..Half Shaft Remover (Adaptor)Half Shaft Bearing Remover (Taper Roller Bearing Type-Adaptors)Half Shaft Bearing and Rear Hub Oil Seal DriverDifferential Case SpreaderDifferential Bearing Removal Ring ..Pinion Head Bearing Inner Cone RemoverjReplacerPinion Oil Seal Replacer (Adaptor)Pinion Bearing Setting GaugePre-load Tester ..Propeller Shaft Flange Holder
EssentialEssentialEssential
EssentialEssentialEssentialEssentialEssentialEssentialEssentialEssentialEssentialEssentialEssentialEssential
EssentialEssentialDesirableDesirableEssentialEssentialEssentialDesirableEssentialEssentialDesirable
Front Suspension and Steering ToolsS.36OO Steering Wheel RemoverS.160 Tie Rod Ball Joint Separator ..S.166 Vertical Link Ball Joint SeparatorS.112 l.F.S. Coil Spring CompressorS.112-1 l.ES. Coil Spring Compressor (Adaptor)
EssentialDesirableDesirableEssentialEssential
Page 15
"1:1
~...'"
RECOMMENDED LUBRICANTS-~HOMEMARKETS
COMPONENT MOBil SHELl. E= D.P. CASTRO!. DUCKHAM'S REGENl
~---~~- -~ .. + ~-~~. ,~-~ I
Mobiloil Shell X·l00 Energol Duckham's HavolineArctic 'OW Esso Extra Motor Oil Nol Twenty 20/20W
ENGINE SUMP~ ., ., Motor Oil 'OW Castrolite ., .,Mobiloil x·tOO Multigrade 20W/30 ., Duckham's HavolineSpedal IOWt30 VIsco Static Q5500 Spednl tOW/3D
. ..... ............
UPPER CYLINDER Mobil Shell & •• Energol Castrollo Duckham's Regent U.c.L.LUBRICANT Upperlube V.COL. V.c.L. V.c.L. Adcoids
.......... ..... .. ISUMMER Esso Extra Energol
CARBURKITOR Mobiloil A X·lOO 30 Motor Oil 30 Motor Oil 30 Castrol XL Nol ''Thirly'' Uavoline 30DASH POTS .. ~ ... ~........ . .. I
WINTER F..sso Extra Energol HavulineMobiloil Arctic X-tOO 20W Motor Oil lOW Motor Oil 20W Castrolite Nol "Twenty" 20/20W
. ,.' •..-.------~-~.~.~". ...
GEARBOX ANI) OVERDRIVE Mobilube- Shell Spiral< Esso Gear Oil Energol E.P. Castrol Dllckham's Unhel1lalREAR AXLE GX,90 90 E.P. GP.90 S.A.E. 90 Hypoy Hypoid 90 Thuban 90
........... ","'- - --- .--~-,- ~~~ ~ -- -- ~ ~.~.
STEERING UNIT Mobilgrease Shell &ro Energrease Calltrolease Dllckham's M.arfak(;REASE GUN M.P. Retinax A Multi·Purpose L,2 I..M. LB,10 Multipurpose 2
Grease H~ -"",-------- ~~~'- -- ----------~-- -- .. , .. '_.._'- - --,--~..
OIL CAN Mobil Shell X·tOO E,ro Energol EYeryman Dllckham's HayolineHandy Oil 'OW Handy Oil S.A.E. lOW Oil G~eral Purpose Oil 20/20W
..~ I~ .. ~- ,~
REAR ROAD SPRINGS OLD REAR AXLE OR ENGINE OIL
.~ ...
BRAKE CABLES Mobilgrease Shell Essa Multi·Purpose Energrease Castrolease Dllckbam's MarfakM,P, Retinax A Grease H L.' Brake Cable Grease K~nol K.G.16 M ultipllrpose 2
.... -~ ~---~-.~
CLUTCH AND BRAKE CASTROL GIRUNG BRAKE AND CLUTCH FLUID WHERE THE PROPRIETARY BRAND IS NOT AVAILABLE, OTHER FLUIDSRESERVOIRS WHICH MEET THE S.A.E. 70 R.3 SPECIFICAnON MAYBE USED.
*Where circuit or other severe competitions are contemplated it is advisable to use oils of high viscosity in ,-iew of the increased temperature encountered.
ANTI-FREEZE SOLUTIONS M.ohilI.·ermavme
ShellAnti-freeze
E".Anti·freeze
B.P.Anti-freeze
CastrolAnti-freeze
Duckham'sAnti-freeze
Smith'sBluecol
The grades listed are not in the order of preference
RECOMMENDED LUBRICANTS-OVERSEAS COUNTRIESS.A.E. & AP.L
COMPONENT MOBIL SUELL E= B.P. CASTROL DUCKHAM'S CALTEX TEXACO DESIGNATION
~-- -,~~- ,-------_.. .,-------- ---- ---- ,'----,,- -,-,. -,,,,.••.. -.,,.- '.-- "'" -- ._--,--~~,~ ,,-,_.~- .--'---_.,ENGINE· X.IOO Multigrade E5S0 EJl:tra MotoJ:' Energo! !I Duckham's Havoline 40 orSUMP Air Temp. of. Mobiloil 20Wj40 or Oil20W/40 or Motor Oil Castrol XXL No' Havoline Special S.A.E.40
A,F. X·too 40 Esso 40 "Forty" 20Wl40 M.M.Over 70° ,., Motor Oil 40
C -,," --------_.,,,- --- -----,----",,--- _._,._------- ,. --~----~-~-_._.
Shell Esso
~Energol Duckham's
40° to 70° ~ Mooiloil A X·IOO Motor Motor Oil Castrol XL Not Havolin.. S.A.E.30
'" 3. Oil 30 3. "Thirty" Q 3. M.M.!l ~
5 ~,.,
~~"-"--,,.,,----,- "'- 0 --_.,-"" "" -_. - ---- "" ,,--~- - _... -,-~"-------
~Q Shell ",O~ E,% (,) Energol
!J)u~kham's ::32,.,
g~~ " ~10° to 40° ;; Mobiloil X·lOO ~~i '" Motor Oil Castrolite Nol Hllvoline S,A.K 20W"7_i< Motor " 0'"0 Arctic ""'Q '.W O"'Q Oil 20 '.W ''Twenty'' ~~ 20/20W M.M.:1 ,.,- "'0- ~O;;;
f2~-----,--_._--~,--
"'''':1 Shell Esso Energol Duckham's ..'"Below !00 Mobiloil X·IOO Motor Motor Oil Castrol Z No' Hamline S.A.E. lOW
lOW I.W Oil lOW I.W "Teo" '.W M.M.
llPPER CYLINDER Mobil Shell Esso Upper Energol Castrollo Duckham's Upper CylinderLUBRICANT Uppe,~lube Dona" U Motor Lubricant V.CI.. Adcoids I.ubricant
---- ----,,,._._-,,,- --,,_. --~-- -,- --- -- ----"'-_._--~CARBURKITOR DASHPOTS USE APPROPRIATE CURRENT SINGLE GRADE ENGINE OIL
---- ...----- -'------ ~--,~,--~,--~---- -"--,,,,'" -'--'- 'T'-
Mobiluhe Shell E...so Gear Oil Energol E.P. Castrol Duckham's Univenal G.L4GEARBOX Over 30° GX.90 Spirax 90 E.P. G.P.I){} S.A.E. 90 Hypo, Hypoid 90 Thuban 90 Hypoid 90
----~~-'-'. -----",-"" -- ----~--_ ..,-----
REAR AXLE Below 30° Mobilube Shell Spira" Esso Gear Oil Energ<:lI KP. Castrol Duckham's Universal G.L.4GX.SO 80 E.P. G.P.80 S.A.E. 80 Hypoy Light Hypoid 80 Thuban SO Hypoid SO
-----------STEERING UNIT Mobilgrease Shell EIiSO Multi- Energrease Castrolease Duckham's MarfakGREASE GUN M.P. Retinax A Purpose Grease H L2 L.M. I..B.I0 Multipurpose 2
,--I- " -----------
Energol Duckham'sOIL CAN Mobil Sbell X-too Motor Oil Everyman General Purpose Home
Handy Oil '.W Handy Oil S.A.E.20W Oil Oil Lubricant.."L
REAR ROAD SPRINGS OLD REAR AXLE OR ENGINE OIL
E&..o CastroleaseBRAKE CABLK'i Mobilgrease Shell Multi-Purpose Energrease Brake Cable Duckham's Marfak
M.P. Retinax A Grease H L2 Grease Keenol KG 16 Multipurpose 2------ ,,--.'.-.'" .. --- --,-" -,,-~------
CLUTCH AND BRAKf( CASTROL G1RLlNG BRAKE AND CLUTCH FLUID
IWHERE THE PROPRIETARY BRAND IS NOT AVAILABLE OTHER FLUIDS
RK'iERVOIRS WHICH MEET THE S.A.E.70 R3 SPECIFICATION MAY BE USED.
" Where circuit or other severe competitions are ('ontemplated it is advisable to use oils of high viscosity in view of the increased oil temperature enJ:ountered.
ANTI-FRF-EZE SOLUTIONS 8.P. Mobil Sbcll EllllO Castrol Du~kham'll Smith's
The grades listed are not in the order of preferen~e?--.J
Anti-frost Perma:Wne Anti-freeze Anti-freeze Anti-freeze Anti-freeze 8Iu('('01
JACKING AND TOWING
Jacking (Fig. 3)Using the jack provided in the tool kit, raise
either side of the vehicle for road wheel removal,as follo\VS :-I. Ensure that the handbrake is applied and one
of the wheels remaining on the ground ischocked.
2. Lift the floor covering adjacent to the doorsill and remove the rubber grommet fromthe aperture in the floor panel.
3. Lower the jack through the aperture andengage the jack lug with the slotted bracketon the chassis frame.
4. Using the ratchet jack handle included in thetool kit, rotate the hexagonal shank of thejack clockwise to raise the vehicle.
5. To lower the jack, reverse the position of theratchet handle and turn it counter--clockwise.
Front End (Fig. 1)When raising the front end for servicing, place
a hydraulically operated trolley jack under thefront crossmember centrally between the frontwheels, and place chassis stands under the chassisside members rearward of the front suspension.
Rear End (Fig. 2)Raise the rear end using a trolley jack under
the centre of the rear axle and place chassis standsunder the chassis side members forward of therear springs.
TowingOne or two methods of towing may be
employed when moving the car.(a) A towing ambulance, which may be placed
under the front crossmember, or under therear axle, depending upon the tow required.
(b) A towing rope secured to the front cross-member.
Fig. 1. Using an hydraulic trolley jack under thefront cross-member
Fig. 2. Jacking WIder the rear axle
NOTE: Do NOT jack up or tow the vehicleusing the radiator cradle.
PallO 18
Fig. 3. The car jacklocated in the chassislifting bracket
GLOSSARY OF PART NAMES AND ALTERNATIVES
ENGINE
FUEL
CLUTCH
GEARBOX
REAR AXLE ..
ELECTRICAL ..
Gudgeon PinInlet ValvePiston Oil Control RingInduction ManifoldOil SumpCore PlugDipstickSilencer ..
Carburettor ChokeSlow Running JetVolume Control Screw ..Fuel PumpAir CleanerFuel TaukAccelerator
Clutch Release BearingClutch LiningSpigot Bearing ..Clutch Housiug ..
Gear LeverSelector ForkInput Shaft
CountershaftSynchro ConeReverse Idler Gear
Crowu WheelBevel Pinion'U' BoltsAxle ShaftDifferential GearDifferential Pinion
GeneratorControl BoxCapacitorInterior LightLeusHead Lamp RimDirection IndicatorsMicrometer AdjustmentRear Lamps
Piston pin. Small-end pin. Wrist pin.Intake valve.Piston scraper ring.Inlet manifold. Intake manifold.Oil pan. Oil reservoir. Sump tray.Expansion plug. Welch plug. Sealing disc.Oil dipper rod. Oil level gauge rod. Oil level indicator.Muffler, expansion box, diffuser.
Carburettor Venturi.Low speed jet. Idler jet.Idling mixture screw.Petrol Pump. Fuel lift pump.Air silencer. muffler.Petrol tank.Throttle.
Throwout bearing. Thrust bearing.Disc facing. Friction ring.Clutch pilot bearing.Bell housing.
Transmission.Change speed lever. gearshift lever.Change speed fork. Shift fork.Constant motion shaft. First motion shaft, drive gear.First reduction pinion. Main drive pinion. Clutch shaft.Clutch gear.Layshaft.Synchronizing ring,Reverse Pinion.
Final Drive Unit.Ring gear, final drive gear, spiral drive gear.Small pinion, spiral drive pinion.Spring clips,Half·shaft. Hub driving shaft. Jack driving shaft.Sun wheeLPlanet wheel.
Dynamo.Cut-out, voltage regulator, voltage control, circuit breaker.Condenser,Dome lamp.GlassHead lamp surround. Head lamp moulding,Signal lamps, flashers.Octane selector.Tail lamps.
Page 19
GLOSSARY OF PART NAMES AND ALTERNATIVES - continued
STEERING
BRAKES
BODY ..
Drop ArmRocker ShaftSwivel PinStuh AxleTrack RodDraglink ..Steering ColumnSteering Column BearingSteering ArmStarter Tube
Master CylinderBrake Shoe Lining
BonnetLuggage LockerLuggage Locker LidMudguardsRoofNave PlateFinishing StripWindscreenRear WindowQuarter Vent
Pitman arm.Pitman shaft. Drop arm shaft.Pivot pin. King pin. Steering pin.Swivel axle.Cross tube. Tie rod.Side tube. Steering connecting rod.Steering gear shaft.Mast jacket bearing.Steering knuckle arm.Control tube.
Main cylinder.Brake shoe facing.
Hood.Boot. Luggage compartment.Boot lid. Rear deck.Quarter panels. Fenders. Mud wings. Wings.Canopy.Wheel disc. Hub cap.Moulding. Chromed strip.Windshield.Rear windscreen. Rear windshield. Backlight.(N.D.V.). No draught ventilator
Page 20
AbbreviationsL.H.S. - Left-hand side (viewed from driver's seat).R.H.S. - Right-hand side (viewed from driver's seat)
TR.4A
GENERAL SPECIFICATION
The general specifica'tion for the TRAA is the same as that for the TRA except where listed belo\\-':
Performance Data (Engine)Nett
Piston Speed at 100 m.p.h. (top gear)
Cooling SystemRadiator
Fuel SystemCarburettors
Air Cleaners
ClutchType
Rear AxleTypeLive axleI.R.S.Ratio
TYRE PRESSURE DATA
104 RH.P. at 4,700 r.p.m.Torque 1,590 lb. in. at 3,000 r.p.l11.(Equivalent to 154 Ib/sq. in. 8.M.E.P.).2,898 ft/min. at 4,800 r.p.lll.
Pressurised-finned vertical flat tubes. No~loss system.
Twin Stromberg 175 CD. HorizontaLNeedle size~2E up to CTC 54939.. 2H from CTC 54940.Replaceable paper elements.
Borg & Beck Diaphragm spring type, 8V diameter.
Hypoid bevel gears, taper roller bearings.Semi-floating axle shafts, three-piece casing.Final~drive unit rubber mounted.3'70[4'1: I.
TYRE PRESSURES----
Independent rear Rigid rear axleRevs./Mile suspension vehicles vehicles
TYRE at 30 m.p.h. ROLLINGRADIUS PRESSURE~lbs/sq.in. PRESSURE~lbs/sq. in.
Inches Front Rear Front Rear
Goodyear6.95 x 15 G.P. 820 12'3 17 21 19 23
Dunlop165/6.5 x 15 S.P. 820 12'3 24 28 24 28
1\1ichelin .. ..
I165 x 15 'X' .. .. 808 12-48 17 21 17 25
NOTE: The tyre pressures given in the above table are suitable for speeds up to 110 m.p.h. Where cars are to beused for racing, consu!t the respective Tyre Company regarding the need for tyres of full racing construction.
SuspensionFront
Rear-Live axleI.R.S.
Low periodicity independent suspension system. Patented bottom bush and top ball-joint swivels. Coilsprings controlled by telescopic dampers. Taper rollerhub bearings.Wide semi~elliptic springs, controlled by piston dampers.Semi~trailing arm independent suspension with coi!springs controlled by piston dampers. Mounted ontoframe rubber-bushed pivots and with rubber
SteeringTypeCastor AngleCamber AngleKingpin inclinationFront wheel alignmentTurning circle
Chassis DataWheelbaseTrack: Front-Disc WheelsTrack: Front-Disc Wheels
Wire WheelsRear~
LR,S, Disc WheelsWire Wheels
Live Axle Disc WheelsWire Wheels
Ground Clearance (Static laden)
Exterior DimensionsOverall length
widthheight (unladen)Hood erectTop of screenHood folded and screenremoved
CapacitiesWater capacity of cooling system
with beater fitted
Pape 22
TRAA
Rack and pinion unit. Telescopic steering column.2"40' cc 1o t9' = iParallel to ,k-" (1'59 mm.) toe~in.
33' 0" 10 metres.
7' 4" 223,6 em,4' 1" 124'5 em.4' 1" 124·5 em.4' ti" 126·3 em.
4' 01" 123·2 em.4' 1-.tN 125·1 em.4' 0" 122'0 em.4' Of' 123'9 em.
6" 15·24 em.
13' 0" 396 em.4' 10" 147 em.
4' 2" 127 em.3' 10" 117 em.
3' 4" 102 em.
Imperial U.S. Metric10 pints 12 pints 5-7 htres11 pints 13'2 pints 6'25 litres
TR.4A
NUT TIGHTENING TORQVES
The nut tightening torques for the TRAA are as those for the TRA with the addition of those listed below:
SPECIFIED TORQUESlbs. ft. Kg.m.
OPERATION
REAR AXLECrown Wheel to Differential CaseRear Cover AttachmentInner Driving Flange to Inner AxleMounting Plate to Hypoid Housing RearMounting Plate to Hypoid Housing FrontOil Seal Housing to Hypoid Housing
DESCRIPTION
i" x 24 V.N.F. Bolt-i1>" x 24 U.N.F. Setscrewr x 18 V.N.F. Nyloc nutf' x 24 V.N.F. Studi" x 24 V.N.F. Boltf,;" x 24 V.N.F. Setscrew
40 - 4518" 20
100-11026 - 283516 - 18
5·530 - 6·2212'489" 2'765
13'826" 15·2093'595 - 3·8714'8392'212" 2·489
REAR SVSPENSION (Live Axle)Front Spring Eye to Brackets ..Front Spring Eye Brackets to FrameDamper to Frame BracketsSpring to Axle 'V' Bolts ..Damper Link Attachment
Bump Rubber AttachmentsExtension Studs for Wire WheelsWheel Attachment
f' x 18 V.N.F. Bolt 28 - 30 3-871 - 4'148r x 24 V.N.F. Bolt 28" 30 3·871 - 4'14811>" x 20 U.N.F. Setscrew 55 - 60 7·604 " 8'293i" x 24 V.N.F. 'V' Bolt 26" 28 3'595- 3-871-ik- H x 20 U.N.F. 40 - 45 5·530 - 6·221i' x 24 V.N.F. Link 18 - 20 2'489 - 2-765i" x 24 U.N.F. 18 - 20 2'489 " 2·765CL H x 20 U.N.F. Stud 65 8'987"is-" x 20 V.N.F. Nut 55 - 60 7'604 - 8'293
REAR SVSPENSION (I.R.S.)Damper to ,Frame Mounting Brackets.. -ik-# x 20 V.N.F. SetscrewDamper Link Attachment r x 24 V.N.F. LinkInner Driving Flange to Rear Hub and Axle Shaft -r x 24 V.N.F. BoltRear Hub Assembly V x 18 V.N.F. Stub AxleTrailing Arm to Mounting Bracket ,:t;--" x 20 V.N.F. BoltTrailing Arm Mounting Brackets to Frame -r x 24 V.N.F. BoltTrailing Arm to Brake Back Plate -k" x 24 U.N.F. Stud
SPECIAL TOOLS
55 - 6018" 2028 - 30
100-11045" 5028" 3012 - 14
7'604" 8·2932'489" 2·7653-871 - 4'148
13-826" 15'2096·221 - 6·9133·871 - 4'1481-652" 1'936
The special tools required for the TRAA are the same as those for the TRA with the addition of those listed below:
SVSPENSIONS.1l2AS.1l2A-IA
REAR AXLES.101-1S.317S.318S.422IA-16
LF.S. Coil Spring CompressorLF.S. Coil Spring Compressor Adaptor
Differential Case Spreader AdaptorsRear Hub Adjusting Nut WrenchHalfshaft Assembly Holding Jig.Outer Hub Taper Bearing Remover/Replacer Adaptor.
Page 23
TRIUMPH TR4WORKSHOP MANUAL
GROUP 0
Comprising:
Instruments, switches and controls ...
Running-in
Customer preparation Service
Daily and weekly checks
Periodical lubrication and regular maintenance
Lubrication chart
Section 1
"Section 2
"""
TR4 WORKSHOP MANUAL
GROUP 0
CONTENTS
0·101
Section 1Instruments
Switches and Controls
Heating and Ventilation Controls
Locks and Keys
Running-in Recommendations
Section 2Customer Preparation Service
Daily and Weekly Attention
500 Mile Free Service
1,500 Mile Lubrication and Regular Maintenance
3,000 Mile Lubrication and Regular Maintenance
6,000 Mile Luhrication and Regular Maintenance
12,000 Mile Lubrication and Regular Maintenance
Lubrication Chart ...
Page0·102
0·104
0·106
0·107
0·108
0·201
0·202
0·203
0·205
0·207
0·211
0·212
INSTRUMENTS, SWITCHES AND CONTROLS
INSTRUMENTS
1 Fresh air vent controls.2 Overdrive switch (Special Accessory)3 Tachometer4 Turn signal indicator5 Ignition warning light6 Horn button7 Speedometer8 Turn signal control9 Water temperature gauge
10 Oil pressure gauge
11 Fuel gauge12 Ash tray13 Ammeter14 Facia locker15 Panel illumination rheostat16 Headlamp dipper switch17 Clutch pedal18 Brake pedal19 Accelerator pedal20 Parking and headJamp switch
21 Windscreen washer control22 Windscreen wiper switch23 Heat control24 Heater blower switch25 Gear shift lever,26 Heat distribution control27 Ignition/Starter switch28 Handbrake lever29 Scuttle ventilator control30 Choke control
Fig. 1. Arrangement of Instruments, Switches and Controls (L.lI.D.)
Turn Signal IndicatorThe green flashing indicator monitor light, at the
right-hand side of the tachometer, glows intermittentlywhen the direction control is operated and the ignitionis switched on. Sec ''Turn Signal Control'" on page0·105.
TachometerThe tachometer, which is the large instrument on
the left, indicates the engine speed in revolutions perminute and is calibrated in divisions of 100, extendingto 6,000. The speed range within the red segment issubject to special precautions. These are given onpage 0·108.
Fig. 2. Tachometer (Jeft) and Speedometer (right)L.H.D.
Viewed left to right from the driving position, eachinstrument and indicator within the left-hand groupperforms the following function :-
Ignition '\laming LightThe small red warning light at the left of the
speedometer glows when the ignition is sV\'itched on and I
is extinguished when the engine is accelerated. If the Iindicator glows when driving, this indicates an electrical ifault which should be traced and rectified without delay. I
INSTRUMENTS, SWITCHES AND CONTROLS 0·103
SpeedometerThe speedometer indicates the road speed of the
vehicle in miles per hour and is calibrated in divisionsof 2, extending to 120.
The figures within the aperture above the centre ofthe dial may be used to record individual journeys,provided that the figures are fe-set to zero at thebeginning. This is achieved by pushing up and turninganti-clockwise the knob which extends downwards frombehind the instrument.
The figures within the aperture below the centre ofthe dial show the total mileage of the vehicle and maybe used as a guide for periodic lubrication and maintenance.
The High Beam indicator near the bottom of thedial glows only when the headlamp main beams are inusc. When the dipper switch is operated the indicatoris extinguished.
Tachometer and Speedometer IlluminationIllumination of the tachometer and speedometer is
controlled by a switch at the left side of the tachometer.Turn the switch knob clockwise to switch on, andfurther clockwise to dim the illumination. Turn fullyanti-clockwise to switch off.
z
3
1 Trip indicator2 Total mileage indicator3 High beam indicator
Fig. 3. Speedometer
Water Temperature GaugeThe gauge is calibrated in degrees Fahrenheit and
indicates the temperature of water leaving the cylinderhead. The normal operating temperature is reachedwhen the needle registers in the central sector of the dial.
Oil Pressure GaugeCalibrated in Ibs. per sq. in., the oil gauge registers
the pressure of oil fed to the bearings. At speedsexceeding 30 m.p.h., when the oil is hot, the gaugeneedle should register between 65 and 75. A low pressureis normal when idling or running at a lower speed.
Fuel GaugeThe fuel gauge is calibrated relative to the fuel tank
and registers the approximate contents only. When theignition is switched on the needle moves slowly acrossits scale, taking up to one minute to reach a truereading. The needle then maintains a steady readingregardless of vehicle movement.
AmmeterThe ammeter is calibrated in amperes and indicates
the rate of battery charge and discharge. The chargingrate is indicated when the pointer moves to the righthand side of "zero", and discharge, by movement tothe left.
1 Water temperature gauge2 Oil pressure gauge3 Ashtray4 Fuel contents gauge5 Ammeter
Fig. 4. Centre instrument group
0·104 SWITCHES AND CONTROLS
Fig. 5. Upper Central Controls
Lighting SwitchMounted on the central switch panel and identified
by a "Headlamp" sign, the lighting switch is on theextreme left. Pull this out to the first position toilluminate the side, rear, number plate and centreinstrument panel lights. In addition to these, twist theswitch slightly clockwise and pull out to the secondposition to illuminate the headlamps. See "DipperSwitch" .
Windscreen WasherThe windscreen washer control, on the right of the
lighting switch, should be used in conjunction with thewindscreen wiper. Operate by pushing the control tospray clean fluid on to the screen as the wiper bladesdisperse the mud. If the washer has remained unusedfor some time, depress the control a few times to chargethe system.
Windscreen WiperThe windscreen wiper switch is located in the centre
of the panel and to the left of the ignition switch. Pullthe switch knob to operate, and push to switch off, whenthe wipers will automatically return to the parkedposition at the base of the windscreen. The wipers canonly be operated when the ignition switch is turned tothe "ignition" or auxiliary positions.
Choke ControlThe choke control is located on the extreme right of
the panel and is used to enrich the fuel mixture foreasier starting from cold. The control should not beused if the engine is warm, and may not be necessary inwarm climates.
Fig. 6. Ignition Switch positions
1. OFF2. IGNITION3. START4. AUXILIARY
Ignition and Starter SwitchOperated by a separate key, the combined ignition
and starter switch has four positions. These are:I, "Off", in which position the key may be withdrawn;2, "Ignition"; 3. Start; 4, Auxiliary. (See Fig. 6).
With the key in the "Off" position (vertical), tumthe key clockwise to switch on the ignition and auxiliarycircuits.
L__.:::::=::::::::..- ...J~1L!8~5U
To operate the starter motor, turn the key furtherclockwise against spring pressure and when the enginefires, release the key, which will return to the "Ignition"position. If the engine has failed to start, wait untilthe starter motor has come to rest before returning thekey to the "Start" position.
To select "Auxiliary" turn the key anti-clockwisefrom the vertical position. This will enable, for example,the radio to be used with the ignition switched off and,since the key must be withdrawn from the switch to lockthe vehicle, accessories cannot continue to function.
SWITCHES AND CONTROLS 0·105
1 Headlamp dipper switch 2 Clutch pedal3 Footbrake 4 Accelerator pedal
Fig. 7. Foot controlsOverdrive Control
When an overdrive is fitted, the control is mountedon the right-hand side of the steering column cowl. Movethe lever down to engage overdrive, and up to release it.Before using the control, see "Recommended speedlimits" on page O' 108.
Clutch, Brake and Accelerator PedalsThese are conventional items which do not need
further explanation.
Turn Signal ControlThe turn signal lamps are controlled by a lever
mounted on the left-hand side of the steering columncowl. Before making a right-hand turn, move the leverupwards. Move it downwards before turning left.When either left- or right-hand turn signal lamps areoperating, this is indicated by the intermittent flashingof a green indicator light on the facia.
Headlamp Dipper SwitchA foot operated dipper switch, located on the toe
board to the left of the dutch pedal, enables the driverto quickly lower his hcadlamp beams whilst maintainingfull control of the steering and other hand controls.
\\'hen the headlamps arc illuminated, see lightingswitch on pageO"I04, the main beams may be lowered bypressing the dipper switch and releasing it. To returnto the main beam position, again press the dipper switchand release it. The main beam position is indicated bya red warning light near the bottom of the speedometerdial.
HornsOperate the horns by pressing the button in the
centre of the steering wheel.
Gear Shift LeverAll forward gears have synchromesh engagement.
See Fig. 10 for the gear shift positions. Reverse is Fig. 8. Fig. 9.engaged by moving the gear shift lever to the right, 1 T_u_rn_ S1_·:.gJ1_a_l_co_n_tr_o_1 O_v_er_d_r_iv_e_CO_n_fr_o_I _lifting it and then moving it rearwards.
HaudbrakeTo apply the rear wheel brakes, pull the handbrake
lever and retain it in position by pressing the button ontop of the lever. Release the handbrake by pulling itslightly rearwards to free the pawl, then allow the leverto move forward to the "OFF" position.
Seat AdjustmentThe driver's and passenger's seats are adjustable for
leg reach by lifting the lever at the outer side of eachseat and sliding the seat to the desired position, allowingthe lever to re.-engage in the nearest adjustment notch.The passenger's seat backrest hinges forward to provide
Iaccess to the rear compartment. Do not forget to movethe driver's seat forward before lowering or raising the
I"Soft Top". See group 5.
Radio Controls
"
For operating instructions see the radio leafletprovided with the set. This is protected against elec~
I trical damage by a 5 amp. fuse housed in the main lead! union.
Fig. 10. Change speedlever positions
Fig. 11.Handbrake Ic\'cr
0·106 SWITCHES AND CONTROLS
Left-Heater control Centre-Blower switch Right-Distribution controlFig. 12. Heater controls
HEATING AND VENTILATION
Fig. 14. Faciavent control
Fig. 13. Scuttle ventilator and controlsho~n on inset
The heater is designed to heat and distributeincoming fresh air, or if dust and exhaust fumes arebeing admitted, the heater may be used to recirculateair already in the vehicle.
Fresh air is admitted to the heater duct through theopen scuttle ventilator. This is opened by pulling theventilator lever rearwards and closed by pushing itforwards.
When the scuttle ventilator is closed, air is drawn inthrough the open facia vents and recirculated by theheater unit. The facia vents are opened by turning thehandwheel, at the side of each vent, forward.
When the scuttle ventilator is open, cool fresh air isblown out of the open facia vents and may be directedup or down, or may be cut-off by adjusting the handwheel. There is no provision for heating the air blownfrom the facia vents.
The degree of heat given out by the heater unit is---------------------------1 controlled by the left-hand control on the heater control
panel. Pull the control fully out for maximum heat, orpush it fully in for cold. Intermediate positions givevarying degrees of heat.
The blower switch on the centre of the panel controlsa motor-driven fan which stimulates the ftow of freshair from outside when the vehicle is stationary, andboosts the air circulation when the vehicle is moving,The blower is operated by pulling the control to switchon, and pushing it to switch off,
The distribution of warmed air is effected by theright-hand control. Pulling the control fully out directsair to the interior of the vehicle, Pushing the controlfully in directs air to the windscreen only. Intermediatepositions direct air to the screen and interior in varyingproportions,
LOCKS AND KEYS 0'107
LOCKSLocks anti Keys
Two sets of keys are provided, one for operatingthe ignition switch and door locks. and the other forlocking the facia locker and luggage compartment.
Facia Locker (Fig. 15)The facia cubby box may be unlocked by turning
the key a quarter turn clockwise and opened by depressing the locking barrel and pulling on the lipped plate.
Fig. 15. Facia lockerLuggage Compartment (Fig. 16)
To open the luggage compartment lid, turn theunlocked handle counter-clockwise to a vertical positionand raise the lid to its limit before engaging the stay inthe slot provided.
To close the lid, raise it slightly to release the staywhich can then be engaged in its rubber retainer on theboot lid support assembly. Lower the lid and turn thehandle, which may be locked by turning the key a halfturn counter-clockwisc.
Fnel Filler Cap (Fig. 17)The fuel filler cap, located forward of the luggage
locker lid, is opened by depressing a small lever at theside of the cap. Press the cap to close.
Bonnet ReleaseTo open the bonnet, pull the control situated below
the right-hand side of the facia. The bonnet will rise Fig. 16. Luggage locker showing hingedsufficiently to enable the fingers to be inserted under 1 ....:s,;;pa:;r.:e_w.:.·h.:.ee=l.:co.:.v.:.e.:.r _
the rear edge to raise it to a near vertical position, whereit will be supported by a stay. Disengage the stayfrom its recess before closing the bonnet.
Door LocksEither door may be locked from inside or outside
irrespective of which door was last used as an exit.The mechanism automatically prevents the insidehandle being set in the locked position whilst the dooris open. This eliminates the possibility of being lockedout of the car in the event of the key being inadvertentlyleft inside.
Fig. 17. Fuel filler cap
0·108 RUNNING-IN RECOMMEI\'DATIONS
RUNNING-IN FROM NEW
Running-inThe importance of correct running.in cannot be too
strongly emphasized, for during the first 500 miles ofmotoring, the working surfaces of a new engine arebedding down. Power and performance will improveonly if during this vital period the engine receivescareful treatment.
Whilst no specific speeds arc recommended duringthe running·in period, avoid placing heavy loads uponthe engine, such as using full throttle at low speeds orwhen the engine is cold. Running.in should be pro·gressive and no harm will result from the engine beingallowed to "rev." fairly fast provided that it is thoroughlywarm and not pulling hard. Always select a lower gearif necessary to relieve the engine of load.
Full power should not be used until at least 500 mileshave been covered and even then, it should be used onlyfor short periods at a time. These periods can beextended as the engine becomes more responsive.
After 1,000 miles running, the engine can be con~
sidered as fully run-in,
To prevent possible damage to a valve seat as themetal stabilizes during the running-in period, valvegrinding is recommended early in the life of the engine.
Recommended Speed LimitsAvoid over-revving, particularly in the lower gears.
The driver is advised not to drive the car continuouslyat engine speeds above 4,500 r.p.m. in any gear. However, whilst accelerating through the gears it is per~
missible to attain 5,000 r.p.m. for short periods, thisspeed being indicated by a red segment on the tachometer.
When an overdrive is fitted, do not change fromoverdrive to normal 3rd or 2nd gears at engine speedexceeding 3,500 r.p.m., otherwise damage may resultfrom "over-revving".
40 m.p.h.30 m.p.h.
TR.4A
SUPPLEMENT TO GROUP "0" SECTION 1.
The instruments, switches and controls used in TR.4A models are mounted in a walnut facia. They arc similarlypositioned and function as those described for TRA models, except for the following details:-
Panel Illumination RheostatThe panel illumination rheostat switch (item 15, Fig. 1) is positioned in place of the lighting switch (item 20, Fig. 1).
Windscreen Wiper SwitchThe windscreen wipers have two speeds, these being controlled by a two-position pull switch positioned as item 22,
Fig. 1, When the switch is pulled to its first position, the wipers operate at fast speed, when the switch is pulled toits second position, the wipers operate at slow speed.
HandbrakeThe handbrake has been reRpositioned and is mounted on the propeller shaft tunnel.
Recommended Speed LimitsThe recommended speed limits stated on page 0'108 apply to TR.4 models. The following figures apply
to TR.4A models.Avoid over-revving, particularly in the lower gears. The driver is advised not to drive the car continuously at
engine speeds above 5,000 r,p.m, in any gear. However, whilst accelerating through the gears it is permissible toattain 5,500 r.p.m. for short periods, these speeds being indicated by the beginning and the end of the red segmenton the tachometer.
, When an overdrive is fitted, do not change from overdrive to normal 3rd or 2nd gears at engine speed exceeding4,500 r.p.m., otherwise damage may result from "over-revving".Suggested minimum engagement speeds are:
Top gearThird gear
Maximum disengagement speeds are;-
0'109
Top gear3rd gear2nd gear
The above disengagementof the OlD at speeds higher
3'7 AXLE 4-1 AXLEAt driver's discretion At driver's discretion
82 m.p.h. 74 m.p.h.54 m.p.h. 49 m.p.h.
speeds correspond approximately to peak revs. in normal gear. Disengagementthan those stated may cause damage from "over-revving".
CUSTOMER PREPARATION SERVICE
ClJSTO.llEB PBEPABATI01V SEBl"ICE
0·201
Commission Number...
Owner's Name....
Address ..
Engine Number
RegistrationNumber ...
Dale
SpeedometerReading.
Every precaution has been taken at the factory to ensure that the car reaches the customer in thebest possible condition. A few preparatory operations remain, however, which in the best interestsof all, must be carefully carried out by the selling Distributor or Dealer before the car is handedto the customer.
Details of the preparation service are as follows :-
MECHANICAL
o I. Check cooling system for leaks and top upradiator level as necessary_
COACH
o I. Fit front carpets and retainer strips.
o 2. Check carburettors and petrol system forleaks.
o 3. Check brake/dutch master cylinders fluidlevel and top up as necessary.
o 4. Check and adjust tyre pressures.
ELECTRICAL
0 I. Top up battery with distilled water asnecessary_
n 2. Check windscreen wiper operation.~
0 3. Check operation of horn.
0 4. Check all instruments for operation.
5. Cheek flasher operation.
LJ 6. Cheek lamps for operation.
LUBRICATION
n 1. Check engine for correct oil leveL
GENERAL FINISH
0 I. Examine paintwork, touching-up as neces-sary.
0 2. Check interior trim and seats for cleanlinessand seat slide(s) for correct operation.
0 3. Remove all masking tape and anti~corrosive
preparation from chromium plating.
0 4. Wash and polish car, examine for leaks.
0 5. Check tool kit and that all literature ispresent.
ROAD TEST
I. Test car on road.
IMPORTANT
To avoid possible errors, mark the appropriate square as each operation is completedand record on the back of this form any pointsrequiring special attention.
0·202 DAILY AND WEEKLY ATTENTION
DAILY ATTENTION
EngineDaily, or every 250 miles (500 km.), withdraw the
dipstick (l), wipe clean and push fully horne beforewithdrawing it for reading; if the reading correspondswith the lower mark, 4 pints (4-8 U.S.A.) (2'27 htres)will be required for topping up via the cap (3).
RadiatorTop up the radiator with clean rain water until the
level is one inch below the filler neck. This will allowfor expansion of the coolant as the engine warms upand is particularly important if an anti-freeze mixtureis being used, since the expansion allowance will preventunnecessary loss of fluid and consequent dilution asfurther topping up takes place.
CAUTION If the engine is hot, turn the filler cap (2) ahalf~turn and allow pressure to be fullyreleased before completely removing it.
WEEKLY ATTENTION
Fig. 1. Under Bonnet ViewTyres
Adjust the tyre pressures in accordance with conditions and pressure schedules given on page 5.
---------------------------1 Additional information is given in group 3.
BatteryExamine the level of the electrolyte in the cells and,
if necessary, add distilled water via the plugs (4),Fig. 1, to bring the level up to the top of the separators.
Examine the battery terminals and, if necessary.clean and coat them with petroleum jelly. Wipe awayany foreign matter or moisture from the top of thebattery and ensure that the connections and fixings areclean and tight.
IMPORTANTNever use a naked lightwhen examining thebattery, as the mixtureofoxygen and hydrogengiven off by the batterycan be dangerouslyexplosive.
Fig. 2. Topping upthe battery cells
I
II
LUBRICATION AND REGULAR MAINTENANCE (FREE SERVICE)
500 MILES (FREE SERVICE)
Many of the components, including gaskets. bolts and studs, inevitably settledown during the first 500 miles (J ,000 km.) of usc. Therefore, at the completionof this mileage, the vehicle should receive the following attention :~
1. Thoroughly lubricate all chassis points, door hinges, luggage locker and bonnethinges, locks and striker plates, pedal pivots, throttle controls, handbrake cableand rear hubs.
2. Change oil in engine, gearbox and rear axle.
3. Examine and top up if necessary :(a) Water level in radiator.(b) Electrolyte level in battery.(c) Hydraulic fluid levels in brake and clutch systems.(d) S.U. Carburettor dashpots (if fitted).
4. Tighten all nuts where required, particularly those securing the cylinder head,exhaust manifold, exhaust pipe and silencer attachments, steering unit, tie~rods
and levers, differential unit, universal couplings, rear springs and body mountings.
5. Check oil filter attachments for tightness.
6. Check and if necessary adjust :(a) Ignition timing.(b) Fan belt.(c) Carburettor and controls for slow running.(d) Front wheel track alignment.(e) Front hubs, wheel nuts and tyre pressures.(f) Valve clearances.(g) Ignition distributor and sparking plug points.
7. Clean the air filter and fuel pump bowl.
8. Adjust brakes and clutch if required.
9. Check operation of all electrical equipment and focus headlamps.
10. Clean battery terminals, smear with petroleum jelly and check battery mounting but do not over-tighten holding down clamps,
11. Check and tighten starter and generator attachment bolts and terminals.
12. Check all hydraulic pipe connections for tightness and all flexible hoses forclearance.
13. Road test car and report any defects.
14. Wipe clean door handles, controls and 'A'indscreen.
0·203
0·204 1,500 MILE LUBRICATION AND REGULAR MAINTENANCE
Fig. 3.1 Brake master cylinder.2 Clutch master cylinder.
Fig. 4. Steering and Front Suspension Greasing Points
Fig. 5. Propeller Shaft Greasing Points
EVERY 1,500 MILES
Engine Compartment1. Check the levels and if necessary top up the engine
oil sump and radiator header tank.2. \Vipe the master cylinder caps clean, remove them
and check the fluid level in the clutch and brakemaster cylinder reservoirs. If necessary, top up thefluid until it is level with the arrow on the side ofthe reservoirs. Ensure that the breather hole ineach cap is unobstructed before refitting the capsto the master cylinders.
NOTE. As the brake pads wear, the level of fluid inthe master cylinder falls. The addition of fluidto compensate for pad wear is unnecessary.Should the level have fallen appreciably, checkthe condition of the pads. If their conditionis satisfactory, establish the cause of loss andrectify the defect immediately. Refer togroup 3, "Bleeding the Brake and ClutchHydraulic System".
Car Hoisted1. Front Suspension and Steering Tie Rods-take the
weight off the front suspension by jacking up thefront of the chassis until the road wheels are clearof the ground. Using good quality grease, pressurelubricate the nipples 1-5 on both sides of thevehicle. Wipe away all surplus grease to preventcontamination of the disc brakes and tyres.
NOTE. The inner ends of the upper and lower wishbones are mounted on nylon bushes whichsometimes develop a pronounced squeakwhen dry. This can be rectified by occasionallyforcing each rubber dust seal to one side andinjecting a few drops of thin oil.
2. Propeller Shaft-Apply the grease gun to nipplesA and B.
3. Gearbox and Rear Axle-Check each unit forleakage. Rectify and replenish lubricant if required.
Car on GroundI. T}Te pressure-Adjust (See page 5).2. Check tightness of road wheel nuts.3. Wipe clean door handles, steering wheel, gear lever,
handbrake lever and windscreen.
3,000 MILE LUBRICATION AND REGULAR MAINTENANCE 0·205
I<'ig. 6.Engine oil filter
Fig.7.Engine sumpdrain plug
1 Drain plug.2 Filler plug.
Fig. 8.Gearbox drainand filler plugs
I Filler plug.2 Drain plug.
Fig. 9.Rear Axle drainand filler plugs
3,000 MILES
At 3,000 mile intervals, carry out the work listedunder 1,500 miles and the following additional v.'ork:~
Change Engine OilFor average driving conditions, defined below, drain
the oil sump by removing the plug shown arrowed,refit the plug and refill with the appropriate grade of oilat the end of each 3,000 mile period. This period shouldbe reduced for unfavourable conditions or may beextended for those more favourable.Favourable Long distance journeys with little or no
engine idling, on well-surfaced roads, 1--------------------------reasonably free from dust.
Average Medium length journeys on well-surfaced roads with a small proportion ofstop/start operation.
Unfavourable Either of the following:~
(a) Operating during cold weather, especially when frequent engine idling isinvolved.
(b) Extremely dusty conditions.If the vehicle is used for competition or sustained
high speed work, use of higher viscosity oils is advisedbecause of the increased oil temperature. Additiveswhich dilute the oil or impair its efficiency must not beused.
An upper cylinder lubricant, mixed with the fuel in 1 _
the proportions given on the container, may be usedwith advantage throughout the life of the vehicle,particularlY during the running-in period and when theweather is wintry.
Top-up GearboxWith the vehicle standing on level ground, remove
the oil level plug (2) and, using a suitable dispenser suchas a pump type oil can with flexible nozzle, filled withan extreme pressure (Hypoid) lubricant, top up thegearbox until the oil is level with the bottom of thefiller plug threads.
AHow surplus oil to drain away before refitting thelevel plug and wiping clean. Avoid overfilling as thismay result in the oil leaking into the clutch housingwith consequent ill-effects to the clutch facings.
Top-up Rear AxleRemove the oil level plug (I) and, using the same
dispenser as used for topping-up the gearbox, and thesame oil, i.e., extreme pressure (Hypoid) lubricant, topup the rear axle until the oil is level with the bottom ofthe filler plug threads.
Allow surplus oil to drain away before refitting thelevel plug and wiping clean. Avoid overfilling and if anexcessive amount of oil is required, check for leakagearound the driving flange seal and rear cover.
0·206 3,000 MILE LUBRICATION AND REGULAR MAINTENANCE
Fig. 10. Filling Carburettor Dashpots
Carburcttor Dash PotsUnscrew the hexagon plug from the top of each
carburettor and withdraw the plug and damper assem·bly. Top up the damper chambers with the currentgrade of engine oil. The oil level is correct when,utilizing the damper as a dipstick, its threaded plug isi-" (6-3 mm.) above the dash pots when resistance is felt.Refit the damper and hexagonal plug. Using an oil can,apply oil to the throttle and choke control linkages.
I Bleed nipple2 Adjusting rod
Fig.
3 Locknut4 Clevis
11. Clutch Linkage
5 Crosswshaftgreaser
Clutch AdjustmentCheck, and if necessary, adjust the clearance between
the clutch operating piston and the push rod (2). Thecorrect clearance is 0·1" (2·5 rom.). To adjust:-I. Slacken the nut (3) and unscrew the push rod (2)
until all clearance between the push rod and thecupped end of the operating piston (inside slavecylinder) is taken up.
2. Adjust the position of the locknut (3) until a feelergauge of 0·1" (2,5 mm.) thickness may be insertedbetween the locknut face and the clevis fork (4).
3. Without disturbing the locknut on the push rod.screw the push rod into the clevis until the nutcontacts the clevis face, then lock up the nut (3).
Brake adjuster 2 Hub greaser3 Bleed nipple
Fig. 12. Rear Hub and Backing Plate
Front Brake AdjustmentThe disc brakes, fitted to the front wheels, arc self
adjusting and should only need replacement shoe padswhen the linings are reduced to approximately -k '"(3 mm.) thickness.
Rear Brake AdjustmentCheck the travel of the foot brake and hand brake.Each rear brake is provided with a smaller adjuster,
(l), Fig. 12, which is positioned on the brake backingplate, above the axle case, and accessible ~1th the roadwheel removed. To adjust the shoes, turn the adjusterclockwise until the shoes are hard against the drum ;then slacken the adjuster by one notch. If the drumis not free to rotate slacken the adjuster still further.
Hand Brake AdjustmentAdjustment of the rear brake shoes automatically
re-adjusts the hand brake mechanism,
6,000 MILE LUBRICATION AND REGULAR MAINTENANCE 0·207
6,000 MILES
At 6,000 mile intervals, carry out the work listedunder 3,000 miles and the following additional work:-
Ignition DistributorRelease the clips and remove the distributor cap and
rotor arm. Detach the contact breaker points and cleantheir contact faces with a fine carborundum stone. Ifall trace of pitting cannot be removed, fit new contacts.Using a sman screwdriver in the slot (2), adjust themoving contact so that when the contact heel is on thepeak of the cam a 0·015" (0·38 mm.) feeler gauge maybe inserted between the contact faces (7); then tightenthe screw (8).
Apply a few drops of thin oil around the edge of thescrew (3) to lubricate the cam bearings and distributorspindle. Place a single drop of clean engine oil on thepivot (6). Smear the cam (4) with engine oil. A squeakmay occur when the cam is dry.
Refit the rotor arm and ensure that the distributorcap is clean and the central carbon brush is free in itshousing. Refit the cap and secure it to the distributor.
Sparking PlugsRemove the sparking plugs for cleaning and re~set
the gaps to 0·025" (0·63 mm.). Clean the ceramicinsulators and examine them for cracks or other damagelikely to cause "H.T." tracking. Test the plugs beforerefitting and renew those which are suspect.
Water PumpApply a grease gun to the grease nipple and inject
grease until it exudes from a hole in the side of thepump.
Fig. 13. Ignition Distributor
Fig. 14. Water Pump Greaser
all~e
Fig. 16.Air cleanerflange
Fuel Pump BowlClean the sediment bowl as follows :-Disconnect the fuel pipe (1) from the suction side of
the pump and to prevent loss of fuel, fit a taperedrubber or wood plug into the pipe bore Ct J.D.).(0,63 mm). Alternatively, attach one end of a lengthof rubber tube over the end of the fuel pipe and tie theopposite end of the tube above the fuel tank leveL
Unscrew the stirrup nut (2) under the bowl, swingthe stirrup to one side and remove the bowl. Swill outthe sediment bowl and wipe it clean.
To avoid damaging the glass sediment bowl whenrefitting it, tighten the stirrup nut only sufficiently toensure a fuel-tight joint. Reconnect the fuel pipe andprime the carburettors.
Air Cleaners Fig. 15. Fuel PumpRemove and wash the air cleaners in fueL Soak the I-----------.::-.--.:;~---'-----------
gauzes in engine oil and allow to drain before wiping TOPthem clean. When refitting the cleaners, ensure that theholes above the carburettor flange setscrew holes arecorrectly aligned with corresponding holes in the aircleaner and gaskets. (See Fig. 16).
If the engine is operating under dusty conditions,clean the filters more frequently.
0·208 6,000 MILE LUBRICATION AND REGULAR MAINTENANCE
Oil Filter Element (Fig. 17)To renew the element, unscrew the securing bolt 'C',
remove the container and withdraw the element. Washthe container to remove foreign matter trapped by thefilter and discard the old washer 'A'" replacing it by anew one each time the element is renewed.
\Vhen re-assembling the container and a newelement, ensure that the washer 'A' is correctly positioned in its groove in the filter body. Do not tightenthe bolt 'c' more than is necessary to effect an oil-tightjoint.
Before restarting the engine, make sure that thesump is filled to the correct level with clean fresh oiL
Oil Filler Cap (Fig. 1)Remove and swill the cap (3) in fuel, allow to drain
before refitting.
GeneratorUse an oil can to pour a few drops of engine oil
through the hole in the centre of the rear end cap.
B
~--c
A. Washer.B. Element.C. Securing bolt.
Fig. 17.Oil Filter
Fan Belt Tension (Fig. 18)The fan belt should be sufficiently tight to drive the
------------------:.~:.:·--------Igenerator without unduly loading the bearings.Adjust the belt by slackening the adjusting bolt (5)
and the generator pivots (3 and 4). Pivot the generatoruntil the belt can be moved i' to I' (19 to 25 rom.) at itslongest run (6). Maintaining the generator in this position, securely tighten the adjusting bolt and the twopivots.
Fig. 18. Fan Belt Adjnstment Valve Rocker Clearances (Fig. 19)---------'------------------1 Check and, if necessary, adjust the inlet and exhaust
valve clearances to 0·010' (0,25 mm.) when cold. Thesesettings, which are correct for all operating conditions,are obtained as follows :-1. Turn the crankshaft until No. 1 push rod has
reached its highest point, then rotate the crankshafta further complete revolution.
2. To adjust No. 1 rocker, slacken the locknut andinsert a 0·010' (0'25 mm.) feeler gauge betweenthe rocker and valve stem. Turn the adjuster witha screwdriver until slight resistance is felt as thegauge is moved across the valve stem; then retighten the locknut.
3. After tightening the locknut, re-check the clearanceand, if satisfactory, deal with the remaining rockersin a similar manner, ensuring that each rocker iscorrectly positioned before attempting to adjust it.
Fig. 19. Adjusting Valve Rocker Gearances
6.000 MILE LUBRICATION AND REGULAR MAINTENANCE 0'209
Fig. 21. Rear wheel brakes
Fig. 20. Adjusting the front hubs
Rear Hub Bearings (Fig. 12)Lubricate the rear hub bearings by applying the
grease gun and giving 5 strokes to a nipple (2) situatedbehind the rear brake backing plate.
Front Hub Bearings (Fig. 20)Adjust the front hub bearings as follO\vs :Remove the split pin, tighten the hub nut until
slight resistance to hub rotation is felt; then slackenoff the nut by one-half flat and insert the split pinthrough one of the two holes provided.
De-Dust Rear Brake Linings (Fig. 2l)Jack up the rear of the car and remove both road
wheels and brake drums. Examine the brake linings forwear and freedom from oil or grease, Renew worn orcontaminated linings.
Using a high pressure air line, or a foot pump, blowall loose dust from the mechanism and, using a cleandry cloth, wipe the dust from the inside of the drums,Avoid touching the braking surfaces with greasy hands. 1---------------------------
Refit the brake drums and road wheels, re~ad.iust thebrakes and remove the jack.
Interchange Road Wheels (Fig. 22)Uneven tyre wear may be caused by road conditions,
traffic conditions, driving methods and certain featuresof design which are essential to the controL steeringand driving of a vehicle. Close attention to inflationpressures and the mechanical condition of the vehiclewill not always prevent irregular wear. It is thereforerecommended that front tyres be interchanged with reartyres at least every 3,000 miles. Diagonal interchangingbetween near front and off rear and between off frontand near rear provides the most satisfactory first changebecause it reverses the direction of rotation.
Subsequent interchanging of front and rear tyresshould be as indicated by the appearance of the tyres,with the object of keeping the wear of all tyres even anduniform.
When interchanging the wheels, examine each tyreand remove flints or other road matter which may havebecome embedded in the tread. Remove oil or greasewith a petrol- (gasoline)- moistened cloth.
Adjust all tyres to the correct pressure. (See page 5).
Overdrive FilterIf an overdrive is fitted, unscrew the large knurled
drain plug under the overdrive unit and withdraw thegauze filter for cleaning. Refit the filter and tighten thedrain plug.
Replenish the unit with oil, and after a short runusing the overdrive, re-check and adjust the oil level ifnecessary.
The same oil is used both for the overdrive unit andthe gearbox, an internal transfer hole allows oil to flowfrom the gearbox into the overdrive unit until a commonlevel is attained. Do no! use additives; their lise maybe detrimental 10 lhe proper operatloll of lhe unl!.
Fig. 22. Diagram of wheel interchanging
0·210 6,000 MILE LUBRICATION AND REGULAR MAINTENANCE
Clutch Cross Shaft Bearings (Fig. 23)Inject a small amount of grease through a nipple
located at each end of the clutch cross shaft andaccessible from beneath the vehicle.
Clutch and Brake Pedal BearingsUse an oil can to lubricate the clutch and brake
pedal bearings and their linkages. These are accessiblefrom within the driving compartment.
Fig. 23. Clutch Cross~shaft Grease Nipple
Hand Brake Cahle Conduit (Fig. 24)Inject grease through a nipple (1) on the hand brake
conduit until grease exudes from both ends of theconduit. During winter months, frequent greasing atthis point will prevent a frozen hand brake cable.
Hand Brake Compensator (Fig. 24)Inject grease through two nipples (2 and 3) on the
hand brake compensator. Apply oil to all pivot pins.
Fig. 24. Handbrake Cable and Compensator Grease Nipples
Steering UnitRemove a sealing plug from the top of the steering
unit and replace it by a grease nipple. Apply the greasegun and give 5 strokes only. Remove the nipple andrefit the plug. Over~greasing can cause damage to therubber bellows.
Check the tightness of all bolts and nuts, particularlythe front and rear suspension, the steering and thewheel nuts.
Fig. 25. Steering Unit Filler
12,000 MILE LUBRICATION AND REGULAR MAINTENANCE 0·211
Fig. 28. Arrangement of H.T. Cables
12,000 MILES
At 12,000 mile intervals, carry out the work listedunder 6,000 miles, and the following additional work:-
Front Hub Lubrication (Fig. 26)If the car is being used for competition work, fe-pack
the front hubs with grease every 12,000 miles. Thisperiod may be extended to 24,000 miles for normal usc.
To pack the hubs with grease :-Jack up the front of the car and remove one front
road wheeL Without disturbing the hydraulic pipeunions, unscrew the caliper securing bolts (l) and liftthe caliper from the disc, tying it to a convenient pointto prevent it hanging by the attached hydraulic pipe.Note the number of shims fitted between the caliper and Caliper attachments 2 Bleed nipplevertical link. 1 ~F~ig;:.~2~6::..~D~i~se~B::.ra~k~e:...::Ca::::Ii!::pe:::r _
When wire-spoked wheels are fitted, remove thesplined hub extensions by detaching the nuts shownon Fig. 27.
To remove the hub grease cap. screw the No. 10 A.F.setscrew provided in the tool kit into the tapped holein the grease cap.
Withdraw the split pin and remove the slotted nutand "D" washer. Detach the hub assembly and outerrace from the stub axle. Wash all trace of grease fromthe hub and bearings. Pack the hub and bearings withnew grease, working it well into the rollers.
Rewassemble the hub and races to the stub axle,securing them with the "D" washer and slotted nut.Spin the hub and tighten the nut until resistance is feltto hub rotation, then slacken off the nut one-half flatand fit a new split pin. Re-assemble the brake caliperunit to the vertical link, refitting any shims removedduring dismantling. Re-assemble the splined hub Fig. 27. Wire Wheel Nut Extensionextension (if fitted). Refit the road wheel and lower I------~::...::--------------------the jack. See "Warning" on page 3·401.
Repeat the above operations with the oppositewheel hub.
Sparking Plugs (Fig. 28)Renew the sparking plugs at 12,000 miles. When
•replacing the plugs, make sure that they are the correcttype and the gaps are set to 0'025". The types recommended are given on page 4.
Re-connect the plug leads as shown.
Gearbox Oil CbaugeDrain and refill the gearbox. See page 0'205.
Rear Axle Oil CbangeDrain and refill the rear axle. See page 0'205.
Rear Road SpringsPeriodically, relieve the weight of the vehicle from
the rear springs and apply oil to the spring leaveswith a brush or spray. Ensure that the oil penetratesbetween the spring leaves, but avoid contaminating therubber bushes at the end of the spring.
Hydraulic DampersRemove the plugs from the rear dampers and top
up with Armstrong Shock Absorber Fluid to the levelof the bottom of the plug hole. Take care to preventforeign matter falling into the damper. Refit the plugsto the damper.
. .....1 ....:.F:.;i::g.:.,::29:.:.:.....R:.:ea='_Da=:.:rn::pe;:':.,::F;:il:.:le::,'.:.P:.;I:.:u::g -'~
0·212 LUBRICATION CHART
• ..... •... z ...= = '";:: .....z '"... c::l-I- ~.. '"ro
6 ....
AmI/
/
IG
faII,III
II,I
JII
I
L- =
LLBRICATION CHART 0'213
Rcf. Items DetailsPageRef. :Mileage Intervals
\Veekly
\V~kly
\Veeklf
0·2020·209
0·202
0·202
0·204 1,500
To? up
Top up-------I~-----.-~-
�-----~-~~--~
Tyre Pressures and "~'heel Interchanging
Steering SwiwJs (4 nipples) __,___ ._____ . _
9
_~_6~I-B-a-tt-e-r)-"__··· ~~ ~.~~I----
14
I~~~~~ -~~~~~~~~~~~~~--~~-~--~~-~~~--~-~
3 Radiator Water Level
1,500
1,500
1,500
1,500
0·204
0·204
0·204 1,500
0·204
0·204
Gun
Grease Gun
Three or Four Strokes
Outer Tie Rod Ball Joints(4 nipples)
Lower Wishbone Outer Bushes (4 nipples) ...".·~-----I~---~~-------~--~I---~~-
Splines (1 nipple)
Steering
PropeIJer Shaft21
14
14
Slave Drop Arm Pimt---~-------------I
1,500
3,000
Top up Fluid Level 0-204--~-I-----
Oil as Recommended Oil Can 0·206
19
5
6,000
6,000
6,000
0·2040·205 3,000
0.207
0·209
0·207
Grease Gun
Grease Gun
Top up Oil LevelDrain and Refill with New Oil
Top up Oil Level
~~--~I------~
250 Miles
Handbrake
Engine
Clutch Cross Shaft Bearings (2 nipples) "'"._ "..._7
1
20
16
23
24
15
11
----~----~----~-~--~--~
Gearbox 0·205 3,000-I~~~----
0·210 6,000
Compensator (2 nipples) 0·210 6,000~~---~~~--~~~~~-~--------I---~--"--~-~~-----I----~-
0·210 6,000--~~---~I
...... ..... . .....--~~~~~~----~~-~~-~C"-----
Cable (1 nipple)~~~~~-------
Engine Water Pump (I nipple) '"''''''--~--~~~-:--:-~~~-
Hubs~Rear (2 nipples)
Ignition Distributor """ .. ,,,. ."".
Door Locks, Hinges. Bonnet Safc~'¥Catch, Root andWheel Locks . " """
-~-+-~-~-----~-~-~~--"-------
8 Handbrake Lever ..... ......Oil Can
0·210 6,000
6,000
6,000
25 Rear Axle 6.000
13 StL"ering Unit ....
4
17
Air Cleaners
Oil Filter
2 Hubs-~Front
12,000
20 Gearbox 12,000
22 Rear Road Springs Clean and Oil 0·211 12,000
TR.4A
SUPPLEMENT TO GROUP "0" SECTION 2.
Experience and design improvements incorporated in TRAA models have permitted servicing intervals and operatioJils to be revised. The revised schedules, which apply to TR.4A models are listed below.
SCHEDULE OF OPERATIONS RELATING TO "FREE SERVICE"
At the completion of 1,000 miles (1,600 km.) or as near to this figure as possible, perform the following operations:
0·215
ENGINECoolant-Check levelSump-Drain and refillCylinder head-Check tightnessCarburettor-Top up carburettor dash pots and adjust
engine idling speedAccelerator control linkage and pedal fulcrum-OilFan belt-Adjust tensionValves-Adjust clearancesMounting bolts-Check tightnessManifolds-Check tightnessOil filter-Check for oil leaksFnel pump-Clean filter
CLUTCH AND CONTROLSPedal pivot bushes-LubricateMaster cylinder-Top upHydraulic pipes-Check for leakage
TRANSMISSIONGearbox, Overdrive-Check level and top upRear axle-Check level and top upUniversal joint coupling bolts-Check tightness
STEERING AND SUSPENSIONLower steering swivels-LubricateWheel alignment--Check by condition of tyre treadSteering unit attachments and "UH bolts-Check for
tightnessTie rods and levers--Check for tightness
BRAKES AND CONTROLSHandbrake cable and linkage-LubricateHydraulic pipes-Check for leaks, chafing and for hose
clearanceMaster cylinder-Check level and top upPedal pivot bush-LubricateBrake shoes and handbrake cable-Adjust as necessary
ELECTRICAL EQUIPMENTBattery-Check and adjust ievel
Check charging rateDynamo and starter motor-Check fixing bolts for
tightnessDistributor-Lubricate and adjust pointsHeadlamp-Check alignment and adjust if requiredLights, heater, screen washer, wipers and warning
equipment-Check operation
WHEELS AND TYRESWheel nuts-Check tightnessTyres-Check and adjust pressures
BODYDoor strikers, locks and hinges- Oil and check operationBody mounting bolts-Check tightnessDoor handles, controls and windshield-Wipe cleanRoad test-Test vehicle on road
SCHEDULE OF OPERATIONS RELATING TO "A" VOUCHERS
Carry out the following operations every 6.000 miles (10,000 km.) or every six months, whichever is the earlier.
ENGINESom_Drain and refillAir cleaner-Remove element, clean and replaceCarburettor dash-pots-Top upCarburettor idling controls-AdjustAccelerator controls and pedal fulcrum-OilFan belt-Adjust tensionValves-Adjust clearances
CLUTCH AND CONTROLSPedal pivot bushes-LubricateHydraulic pipes-Check for leakage
TRANSMISSIONPropeller shaft-Lubricate (if nipples are provided)
STEERING AND SUSPENSIONUpper steering swivels-LubricateLower steering swivels-LubricateWheel alignment (Front and Rear independent sus
pension models)-Check by condition of tyre tread
0·216 TR.4A
BRAKES A,"ID CONTROLSHandbrake cable and linkage-LubricateHydraulic pipes-Check for leaks, chafing and hose
clearancePedal pivot bushes-LubricateBrakes-Adjust shoes
ELECTRICAL EQUIPMENTDistributor-Lubricate and adjust pointsSparking plugs-Clean, re·set gaps, test and refitLigh~ heater, screen washer, wipers and warning
equipment-Check operation
WHEELS AND TYRESWheel nuts-Check for tightnessTyres-Check and adjust tyre pressures
BODYDoor strikers, locks and hinges-Oil and check
operationDoor handles, controls and windshield-\Vipe cleanTest vehicle on road
SCHEDULE OF OPERATIONS RELATING TO "B" VOUCHERS
Every 12,000 miles (20,000 km.) or every twelve months, whichever is the earlier, carry out the work listed for "'A"vouchers and perform the following additional operations:
ENGINEOil filter-RenewFuel pump--Clean the filter and sediment chamberExhaust system-Examine and report conditionCrankcase breather valve-Dismantle, clean and re-
assemble. Ensure breather hole in oil filler cap isfree from obstruction
Water pump-Grease
TRANSMISSIONGearbox, Overdrive-Check level and top upRear axle-Check level and top upUniversal joint coupling bolts-Check tightness
STEERING AND SUSPENSIONSteering unit attachments and "U" bolts-Check
tightnessTie rods and levers-Check tightnessSteering unit-Grease
BRAKES A,"ID CONTROLSBrake drums and caliper pads-Remove, de-dust and
examine brake shoes, pads, drums, and wheelcylinders
ELECTRICAL EQUIPMENTGenerator-Lubricate rear bearingSparking plugs-Renew
WHEELS AND TYRESFront hubs-Check and adjust if necessaryRear hubs (fitted with Live axle)-LubricateTest vehicle on road
TRIUMPH TR4WORKSHOP, MANUAL
GROUP 1
Comprising:
Engine
Cooling system
Fuel system ...
Exhaust system
Section 1
Section 2
Section 3
Section 4
TR4 WORKSHOP MANUALGROUP 1
CONTENTS
1'101
Engine (Section 1)Dimensions and Tolerances
Oil circulation
Engine and gearbox removal
Engine installation
Replacement unit
Engine dismantling ...
Engine reconditioning
Cooling System (Section 2)Filling, draining and flushing
Pressure testing
Anti-freeze recommendations
Thermostat
Radiator
Water pump ...
Fuel System (Section 3)Fuel pump ...
Carburettors ...
Accelerator pedal details
Exhaust System (Section 4)Manifold details
The exhaust system ...
Page] ·103
JoI07
1·109
I·Ill
] ·112
1·113
l·llS
1·201
1·201
]·203
] ·203
]·203
]·204
1·301
1-303
1·306
1-401
1·402
ENGINE-DIMENSIONS AND TOLERANCES
Dimensions and Tolerances
1'103
Parts and Description ins. mOl. Remarks
CYLINDER BLOCKBlock bore in liners 3 ·6245 - 3 '6260 (92'062 - 92'1004)
PISTON AND CYLINDER LINERS
GRADING DIMENSIONS FOR STANDARD BORE SIZE ONLY (Fig. 33)
GRADE F G H
mm. ins. mOl. ins. mm. ins.Cylinder Liner Bore .. 85·997 3·3857 86·007 3·3861 86·017 3-3865
85·989 3-3854 85 ·999 3-3858 86·009 3-3862
Major Top Dia. 'BB' .. 85-870 3-3807 85 ·880 3·3811 85-890 3-381585-860 3-3803 85 ·870 3-3807 85·880 3 ·3811
.
Major Bottom Dia. 'AA' 85 ·908 3'3822 85·918 3-3826 85 ·928 3 ·383085·898 3·3818 85·908 3-3822 85·918 3-3826
Number of rings 2 compression, J scraperRing groove width:
Top ·. 0·0635 - 0·0645 ( 1·6129 1,638)Centre 0·0635 -0,0645 ( 1-6129 1,638)Scraper 0·1572 - 0·1582 ( 3-993 4'018)
Piston pin bore .. 0·87505 - 0·87530 (22'226 -·22'233)Piston removal From top of block
PISTON PINLength 2·916 - 2·920 (74-06 -74'168)Diameter .. 0'87485 -0'87510 (22,187 - 22,227)Clearance in piston oo5סס·0 - 0'00045 (0'00127 -0,01029)
PISTON RINGSWidth:
Top .. 0·0615 --0,0625 (1,562 - 1'5875)Centre 0·0615 -0,0625 (1,562 - 1'5875)Scraper 0·1552 -0,1562 (3 ·942 - 3,967)
Ring to groove clearance, all rings:Mfg. · . 0·0010 - 0·0030 (0,0254 -0,0762)Wear limit .. 0·0038 (0,0965)
Gaps (in position) all rings 0·010 -0,015 (0,254 -0']81)
VALVE SPRINGSNo. of Springs per valve:Inlet · . 2Exhaust 3
Ffee length :Auxiliary inner (Exhaust only) 1·55 -1·57 (39,37 - 39'878)
Inner 1·88 -1·90 (47 ·752 - 48·360)Outer I ·94 ···1·96 (49276 -49,784)
Valve clearance (cold) :Inlet and Exhaust 0·010 (-254)
1"104 ENGINE-DIMENSIONS AND TOLERANCES
Dimensions and Tolerances
0·010,0·020,0·030 (·254, ·508, ·762)
Big end offset. will pass through liner bore6·248 -6·252 (158·7 - 158·8)2·2327 -2-2335 (55·91 - 56·73)1·1775 -1·1795 (29·90 - 29·96)
0·0028 - 0·0040 (0·071 -0·1016)0·005 (0·127)0·965 - 0·975 (24·511 -24·765)
0·8742 -0·8758 (22·208 - 22·252)1·070 - 1·090 (27-318 -27-686)
0·007 -0·014 (·1778 ·3556)
Parts and Description
CONNECTING RODSTypeLength (centre to centre)Big end - Bore ..
- WidthBig end bearing clearances:
Mfg...Wear limit ..
Big end bearing' width ..Small end bearing bore when
reamed . .Width
Connecting rod end float, oncrankpin
Undersize big end bearings available ..
Max. connecting rod bend andtwist .. 0·002
ins.
(-0508)
mOl. Remarks
- 52-9964)- 30·3241)- 62·9793)
CRANKSHAFTCrankpin diameterCrankpin width ..Main journal diameterUndersize main bearings available
Main journal length:FrontCentreRear ..
Main bearing wall thicknessMain bearing housing dia.Main bearing clearance:
Mfg...Wear limit "
Crankshaft end float
Mfg.Wear limit ..
2·0861 - 2·0866 (52·96891·1865 -1·1915 (30·19712-4790 - 2·4795 (62 ·9660·010, 0·020, 0·030,
(-254, ·508, ·762)
1·776 - 1·786 (45·1104 .- 45·3644)1·7498 -1·7507 (44·4549 -44·4678)1·808 -1·818 (45·9232 -46·1772)0·0720 -0·07225 (1·8288 - 1·83400)2·6250 - 2·6255 (66·675 -66·6877)
0·0015 -0·0025 (·0381 - ·0635)0·0031 (-0787)0·004 -0·006 (·1016 - ·1524)
(desirable)0·0048 -0·0117 (-12192 - ·28118)0·015 (-381)
OIL PUMPOuter Rotor:
External diameterHousing internal diameter . .Depth of rotorHousing depth
Inner Rotor:Major diameterMinor diameterRotor depth ..
Spindle diameter ..Bore in housing for spindleSpindle clearance in housing
1·5965 - 1·5975I ·603 - 1·604I -4985 - 1·49951·500 - 1·501
1-171 -1·1720·729 - 0·731I -4985 - 1-49950-4980 -- 0·49850·4995 - 0·50100·001 - 0·003
(40·5511 - 40·5765)(40·7162 - 40·7416)(38·0619 - 38·0873)(38·1 - 38·1254)
(29·7434 - 29·7688)(18·5166 - 18·5674)(38·0619 - 38·0873)(12·6492 - 12-6619)(12·6873 - 12·7254)( ·0254 - ·0762)
Dimensions and Tolerances
Parts and Description ins. mm.
1,71725-1,71825 (43'61815-43'64355)
0-0028 -0,0047 1'07112 - -ll938)0·0059 ('14986)
- 47-6685)- 28,829)- 19-304)- 33,5915)-47,7428)
-43'6624)- 47,5488)- 30·734)-19'304)
(43 ·637(414984(30-226(18'796
(41'6304(28,321(18,796(33 ·0835(47,7199
1'0381 - 0'766)1'09398)(6'604)('1016 .- '19(5)
- 1-7158- 1·872-- 1·210-0-760
-1·8775-1-135-0'760- 1-3225- 1·8757
1·71531·8701·1900·740
1-8760l·ll50·7401·30251·8748
0·0015 - 0-00290·00370·2600·0040 - 0·0075
CAMSHAFTNumber of bearingsFront journal diameterCentre intermediate and rear
journal diameterFront bearing lengthCentre and rear bearing length ..Intermediate bearing lengthJournal length :
FrontCentreIntermediateRear ..
Front bearing internal dia.Centre, intermediate and rear
bearing internal diameter ..Clearance between front bearing
and journal:Mfg...Wear limit ..
Clearance between centre, inter~
mediate, rear bearings andjournals:
Mfg...Wear limit
Cam. lift (max.)Camshaft end float
TAPPETSLength
Stern diameterBlock bore for tappetClearance in block - Mfg.
- Wear limit
1·969 - 1-9710·9367 - 0·93710·9373 - 0·93800·0002 - 0·00130·0016
(49'8069(23'7922(23'8074( ·00508( -04064)
-49-8119)- 23'8023)-23'8252)
-·03302)
(49,5732 -·49'6748)(32'9955 - 33 -0962)
(-0254 -0762)1'0965)(-0762- '127)1'0762 -- '127)(-16002)
VALVESHead diameter - Inlet
- ExhaustAngle of seat (Valves)Angle of seat (Cylinder Head)Valve stern diameter:
Inlet ..Exhaust
Valve guide bore:Inlet ..Exhaust
Stem to guide clearance:Inlet - Mfg.
- Wear limitExhaust -- Mfg.Exhaust "~ Mfg.
- Wear limit
1·558 - 1·5621·299 - 1·30345'441'
0·310 -0,3110·3705 - 0·3715
0·312 -0·3130-3745 - 0·3755
0-001 - 0·0030-00380-003 - 0·0050-003 _.- 0·0050·0063
(1'864(9-4107
(7,9248(9'1523
- 7-8994)- 9'4361)
-7'9502)- 9-5377)
VALVE SEAT INSERTSRefer to page I-125 for details
ENGINE DETAILS (Fixed Parts)
I-1M
82 I Z J 6 7 8 <f 10 II 12 13 14 IS 16
\
I 'i I I K', 10 ,"g. I
l I 1 Split collets 42 Oil pump filler gaUl!.'
17 2 Adjusting 5CTeW 43 Bolt
3 Nut 44 Setscrew and spring washer4 Rocker pedestal 45 Spring washer5 Nut and spring washer 46 Nut6 Rocker, R.B. 47 Oil pump
20 7 Spring 48 Oil pump gasket8 Spring--eentre 49 Dipslkk9 Rocket cover 50 Scaling piece
73 ,"'''-.Ii "-,-_, . I' 1 lLL..-------- ---- 22 10 Fibre washer 51 Front sealing bkx:k
"-, ~ ",- ~ ~-) 11 Nyloctlut 52 Screw72 "" '" -'-, ... /23 12 Plain wa,h",r 53 NUl and spring washer
71 _ "'" ~ // 24 13 Lifting eye 54 Engine mounting~_~I. ~ , ',:,<', ~. 14 Flncr cap 55 Main !leMing cap b,,,11 ;md\fldng washer70 ,U
l~~ ~,__ _~ /' I 25 15 Rocker covef gasket 56 Front main bl'aring cap
_ D" ~~ - ::J~~--' ~'@" ~." 16 Screwandshakeproofwa,her 57 Gasket69 - '::-11 _ - • ," 69°':,» ~'" ,.." -'. 26 17 Rear rocker pedestal 58 Front bearer plale
68 JL -'-8 ",lD •r~"" ~ tr J _ it!~ \\~ ~ 27 .18 Cylinder head 59 Setscrew and spring washer-. • ~ 1/' Ay' \ ~ ~/ / 19 Cylinder hcad gasket 60 Se(~crewandspnngwasher
67 JL -I'll Q 191ft~ .- r!J~>j;';~ \, ~.]; / " 20 C,"oO", II,", 61 Te<q'w """,,,,, '"'' 'IOU Ii"ff"11 - -'~ UI - • 11 ,I(, -.Jt-~:'-~ 4" \ ........ \ D ,./ 21 Cyhnder head stud 62 hhrc washer
66 C~.-/iCl l l~"" .. ~~ 11 f, _~- ~~ }~j • ~ 2'J 22 Linergaskct 63 Shoulderetlstud
23 Drain lap und fibre washer fA Spring washer24 Stud 65 Bolt25 Setscrew and spring washer 66 Lifting eye26 Rear oil re'"J 67 Nut and spring ",a,her27 Rear main rearing Clip 68 Tappet28 Scaling felt 69 Pushwd29 Distributor drive gear bush 70 Exhll<L~t villve:\0 Oil gallery plug and copper washer 71 Tnlet valve31 Set",rew 72 Exhamt valve guide32 Spring wasru;r 73 Collar:n Nlit 74 Auxiliary valve spring34 Breather pipe 75 Inner valve spring35 Oil filter alluehment bolt and spring wa~her 76 Outer val"e spring36 Cylinder block 77 tnlet val"e guidc37 Sump gasket 78 Valve collal38 Centre main bearing Clip 79 Rocker ~hafl cnd cap39 Sump 80 Mills rin40 Breatber pipe ora"ket and diSlance pie<..--c RI Spring41 Sump ptug 82 Rocker, L H.
/.! ,
I / , '"55 54 53 51 50 4'J 48 45 44 '43 42 COJ~
HR. 1. FJl!<:llle Ol'hlih (Fixed parts)
Fig. 2. Oil circulation(side view)
Fig. 3. Oil circuJation(end view)
ENGINE OIL CIRCULATION H07
121
120
114
li5
:16
t"':il7 Z
/~
:2118 '"/ '"t"':119 ::::
0
"'>,.
124125 123 C095
132133 131135
\ 136137
1,54... ' ~"~'~~~U~~~~Ir-,@lf ,t: ~. '.-. . ,~\ \ -~,; ! J !J \ \
153,/ J!j . I \ tl \ \ \152/ /1 I \ \ \
/ 150! 148 146 \ 144 142 \ 140 \ 138151 /49 147 145 143 141 139
Fig. 4. Engine Ddlllls (Moving parts)
Key to Fig, 4
83 Bolt and spring wash", ,.) Compression ring (laper) 135 Front main bearing shell
"' Timing cover 110 Compre;;sion ring (parallel) ,% Shim washer O{lO4" (0-[ mm,)
85 GllSkel III Oil control ring In Shim washer 0-006" (0-15 mm.)
En Timing chain m Piston 138 Cral1hhafl sprocket
" Oil seal II) Gudgeon pin 139 Oillhrower disc
8R Split pin 114 Cirdip '" Boll
89 \\'asher 115 Gudgeon pin bush '" Pulley
'" Tensioner blade 116 C0I111iXting rod 142 Pulky huh
91 Bolt 117 Flywheel 143 Starting handle dog boll
n Tcn,ioncr pin 118 l.ockplate '''4 W~,her and ,,01
93 Lockplaj~ 119 Boit 145 Fan extension
94 Camshaft ,pmckd 120 Tab washer 146 Ruhber bush
" &)11 and spring washer 121 Bolt '47 D;slan~", tube
% Fr"nt camshaft bearing 122 Staner ring gear ,<$ Fan
';7 Camshaft 123 Dowel ,<9 Rubber h(l~h
" Oi,tribulor drive gear 124 Sp;gol bearing 150 Plain wa,her
9'; Ga,kd 125 Rear main bearing 'hdl 151 Plate
100 Di,;trihutor pede,tal 126 CmHod be"r;ng snell 152 Balaneer
101 Stud 127 C,m·rod cap 153 Bolt
110 Spring washer 128 LGckpiale 154 Lockplate
10"' Peg holt 129 Con-rod boit 155 W,xxJmlk key
104 TJcbomete' drive ge~r no Dowel 1.% Oil pump drive $haf,
105 Rubber '(Y ring 131 Cemre main be"r;ng "lteil 157 Intermediate from ~ilm,I,,\ft bearing
iOti Drive gear hou'ing; 132 Lo"'er In""1 ,,'asher 158 Peg bolt
107 C~? 133 CranbhMl 159 lippe, Ibn!'t \v~,h~,
109 Mill,; pin 134 W'lodrul", key, IW Intermcdiatc reM Gam,h~n bearin"
1M Rear camshaft bearing
ENGINE DETAILS (Moving Parts)
83 64 85 86 87 88 89 90 91 92 93 94 95 96 97
'54
148 146 144 \ 142145 143 141
155
\\
\ 138 \ 136139 137
Fig.4. Engine Delfiils (Mo"ng parts)
\131
1\8
/( 119
123 C09S
Key to Fig. 4
8.1 Bolt and spring wa'her 109 Comprcs,ion ring (taper) 135 Front main bearing 'hell
'" Timing cover 13O Compression ring (parallel) 136 Shim wa,her O{lOr (O-I mm.)
" Ga,ket III Oil conlwl ring 137 Shim waoher 0{)06~ ;0-15 mm.)
"' Timing chain lI2 Piston "8 Crankshaft sprocket
"' Oil ,cal 113 Gudgeon pin 139 Oil thm",-cr disc
88 Split pin 1>4 Cirdip 1M' Boll
" Washer '15 Gudgeon pin bnsh ," Pulley
90 Tension"r blade 116 Connecting rod 142 Pulley hub
" Rolt 117 Flywheel >43 Starting handle dog Mit
92 T~nsionef pin 118 Lockplale 144 Washer and nut
9.1 Lockplate 119 Boll >4' Fan extension
94 Cam'haft sprocket 120 Tab ",a,her ''''' Rubber bush
95 Rolt -In<j spring washer 121 """ >47 Dj,tance tube
% Fmn! camshaft b~aring 122 Staner ring gear 148 Fan
'"J7 Camshaft 123 Dowel >49 Rubber bmh
9& Di,:ributor driv" gear 124 Spigol bearing 150 Pbin washer
"" Ga_'kct 115 Rear main bearing shell 151 Plate
'00 Di,trihulor pcd6lal 126 COll.rod bearing shell 152 Balancer
WI S:ud 127 Con_rod caD 153 Bolt
102 Spring wa,her "8 LDckplate 154 Lllckplate
103 Peg holt 129 Con-rod holt 155 Woodruffe key
'04 T'Khomelcr drive gear 130 Dowel 156 Oil pump drive shaft
W5 Rubber '0' ring 131 Ccn:rc main bearing 'hell 157 Inlcrme.diatc I"mnt ~ams;h"rl bearing
1O" Dri'·e geM hOll,ing 132 LO"'¢r Ihr",t w'lsher 158 Peg boll
107 Cap 13.1 Crili1k,hafl 159 Upper IhrlJS;1 w;hher
I(l~ Mills pin 134 Woodrulfe keys '00 lntermediatc reM cam_,-haft bearing
'M Rear cam,haf: bearing
ENGINE REMOVAL H09
ENGINE Al'iD GEARBOX REMOVAL
Remove the battery and drain the coolingsystem, engine and gearbox.
Refer to Fig. 5 and disconnect:- oil pressure pipe (6).- fuel pipe (5).- tachometer drive cable (7).- fuel pipe (2).- vacuum pipe (8).- coil S.W. cable (4).- temperature transmitter cable (3).-horns (I).- fan belt.- engine earthing strap. (Not shown).
Fig. 5. Left~hand view of Engine
Refer to Fig. 6 and disconnect:- heater valve control (12).- hoses (13) aod (14).- mixture control cable (10).- accelerator rod (11) and remove the
carburettors (9).- exhaust pipe flange (not shown).
Fig. 6. Right~hand view of Engine
Referring to Fig. 7:- remove the coupling bolt (I).- release two 'u' bolts (2).- move the steering unit (3) as far forward
as possible.- remove the front cross tube (4).
Fig. 7. Steering unit attachment