7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 1/29
1
VIII. Three-phase
Induction Machines
(Asynchronous Machines)
Induction Machines
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 2/29
2
Introduction
• Three-phase induction motors are the most common and
frequently encountered machines in industry
– simple design, rugged, low-price, easy maintenance
– wide range of power ratings: fractional horsepower to 10 MW
– run essentially as constant speed from zero to full load
– speed is power source frequency dependent
• not easy to have variable speed control
• requires a variable-frequency power-electronic drive for
optimal speed control
Construction
• An induction motor has two main parts
– a stationary stator
• consisting of a steel frame that supports a hollow, cylindrical core
• core, constructed from stacked laminations (why?), having a number
of evenly spaced slots, providing the space for the stator winding
Stator
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 3/29
3
Stator
– a revolving rotor
• composed of punched laminations, stacked to create a series of
rotor slots, providing space for the rotor winding
• one of two types of rotor windings
• conventional 3-phase windings made of insulated wire (wound-
rotor) » similar to the winding on the stator
• aluminum bus bars shorted together at the ends by two aluminumrings, forming a squirrel-cage shaped circuit (squirrel-cage)
• Two basic design types depending on the rotor design
– squirrel-cage
– wound-rotor
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 4/29
4
Induction motor types according to rotor construction:
• Squirrel cage type:
- Rotor winding is composed of copper bars embedded in the rotor
slots and shorted at both end by end rings
- Simple, low cost, robust, low maintenance
• Wound rotor type:
- Rotor winding is wound by wires. The winding terminals can be
connected to external circuits through slip rings and brushes.- Easy to control speed, more expensive.
Squirrel cage rotor
Wound rotor
Notice the
slip rings
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 5/29
5
Squirrel-Cage Rotor
/rotor winding/rotor winding
short circuits all
rotor bars.
Cutaway in a
typical wound-
rotor induction
machine.
Notice the
brushes and the
slip rings
Brushes
Slip rings
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 6/29
6
Rotating Magnetic Field
• Balanced three phase windings, i.e. mechanically
displaced 120 degrees form each other, fed by
balanced three phase source
• A rotating magnetic field with constant magnitude
is produced, rotating with a speed
Where f e is the supply frequency and P is the no. of
poles and nsync is called the synchronous speed in
rpm (revolutions per minute)
120 esync
f n rpm
P
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 7/29
7
Principle of operation
• This rotating magnetic field cuts the rotor windings and produces an
induced voltage in the rotor windings
• Due to the fact that the rotor windings are short circuited, for both squirrel
cage and wound-rotor, and induced current flows in the rotor windings
• The rotor current produces another magnetic field
• A torque is produced as a result of the interaction of those two magnetic
fields
where ind is the induced torque and B R and BS are the magnetic flux
densities of the rotor and the stator respectively
ind R skB B
Induction motor speed
At what speed will the induction motor run?
– Can the induction motor run at the synchronous speed, why?
– If rotor runs at the synchronous speed, which is the same speed of
the rotating magnetic field, then the rotor will appear stationary to
the rotating magnetic field and the rotating magnetic field will not
cut the rotor. So, no induced current will flow in the rotor and no
rotor magnetic flux will be produced so no torque is generated and
the rotor speed will fall below the synchronous speed
– When the speed falls, the rotating magnetic field will cut the rotor
windings and a torque is produced
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 8/29
8
• So, the induction motor will always run at a speed lower than the
synchronous speed
• The difference between the motor speed and the synchronous speed is
called the slip
Where nslip= slip speednsync= speed of the magnetic field
nm = mechanical shaft speed of the motor
slip sync mn n n
The Slip
sync m
sync
n ns
n
Notice that:
if the rotor runs at synchronous speed
s = 0
if the rotor is stationary
s = 1
Slip may be expressed as a percentage by multiplying the above eq. by 100,
notice that the slip is a ratio and doesn’t have units
where s is the slip
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 9/29
9
Electrical Frequency of the Rotor
An induction motor works by inducing voltages and currents in the rotor of the machine, and for that reason it has sometimes been called a rotating
transformer. Like a transformer, the primary (stator) induces a voltage in the
secondary (rotor), but unlike a transformer, the secondary frequency is not
necessarily the same as the primary frequency.
.
If the rotor of a motor is locked so that it cannot move, then the rotor will
have the same frequency as the stator. On the other hand, if the rotor turns at
synchronous speed, the frequency on the rotor will be zero. What will the
rotor frequency be for any arbitrary rate of rotor rotation?
Electrical frequency of the rotor is referred as the rotor frequency and
expressed in terms of the stator frequency, f e:
er sf f
msyncslipr nnP
nP
f 120120
or in terms of the slip speed:
Ex1. A 208-V, 10hp, four pole, 60 Hz, Y-connected induction motor has a
full-load slip of 5 percent
a) What is the synchronous speed of this motor?
b) What is the rotor speed of this motor at rated load?
c) What is the rotor frequency of this motor at rated load?
d) What is the shaft torque of this motor at rated load?
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 10/29
10
a)
b)
c)
d)
120 120(60)1800
4
esync
f n rpm
P
(1 )
(1 0.05) 1800 1710
m sn s n
rpm
0.05 60 3r e
f sf Hz
260
10 746 / 41.7 .
1710 2 (1/ 60)
out out load
mm
P Pn
hp watt hp N m
Solution:
Ex2.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 11/29
11
Conventional equivalent circuit
Note:
• Never use three-phase equivalent circuit. Always use per-
phase equivalent circuit.
• The equivalent circuit always bases on the Y connection
regardless of the actual connection of the motor.
• Induction machine equivalent circuit is very similar to the
single-phase equivalent circuit of transformer. It is composed
of stator circuit and rotor circuit
Equivalent Circuit of Induction Machines
Note that the frequency of the primary side (stator), f e is not the same asthe frequency of the secondary side, f r , unless the rotor is stationary, i.e.
frequency of V P is f e and the frequency of E R is f r where
er sf f
and
1 E a E eff R
here aeff represents the turns ratio.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 12/29
12
The primary internal stator voltage E1 is coupled to the secondary E R by an ideal
transformer with an effective turns ratio aeff . The effective turns ratio aeff is fairly easy to
determine for a wound-rotor motor- it is basically the ratio of the conductors per phaseon the stator to the conductors per phase on the rotor, modified by any pitch and
distribution factor differences. It is rather difficult to see aeff clearly in the cage of a case
rotor motor because there are no distinct windings on the cage rotor. In either case, there
is an effective turns ratio for the motor.
In an induction motor, when the voltage is applied to the stator windings, a voltage is
induced in the rotor windings of the machine, In general, the greater the relative motion
between the rotor and the stator magnetic fields, the greater the resulting rotor voltage
and rotor frequency, The largest relative motion occurs when the rotor is stationary,
called the locked-rotor or blocked-rotor condition, so the largest voltage and rotor
frequency arc induced in the rotor at that condition, The smallest voltage (0 V) and
frequency (0 Hz) occur when the rotor moves at the same speed as the stator magnetic
field, resulting in no relative motion, The magnitude and frequency of the voltage
induced in the rotor at any speed between these extremes is directly proportional tothe slip of the rotor. Therefore, if the magnitude of the induced rotor voltage at locked-
rotor conditions is called E R0, the magnitude of the induced voltage at any s lip will be
given by the equation
0 R R sE E
0222 R Re Re Rr R sX L f s Lsf L f X
00 / R R
R
R R
R
R jX s R
sE
jsX R
E
I
0
0
/ R R
R R
jX s R
E I
Hence
0, / R Req R jX s R Z
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 13/29
13
Finally, the resultant equivalent circuit is given by
01 Reff E a E
where
eff
R
a
I I 2
Reff Ra R 22
02
2 Reff X a X
eq Reff Z a Z ,2
2
The rotor resistance R R and the locked-rotor rotor reactance X R0 are
very difficult or impossible to determine directly on cage rotors, and
the effective turns ratio aeff is also difficult to obtain for cage rotors.
Fortunately, though, it is possible to make measurements that will
directly give the referred resistance and reactance R1 and X1, even
though R R, X R0 and aeff are not known separately.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 14/29
14
Power losses in Induction machines
• Copper losses
– Copper loss in the stator (PSCL) = I 12 R1
– Copper loss in the rotor (P RCL) = I 22 R2
• Core loss (Pcore)
• Mechanical power loss due to friction and windage
• How this power flow in the motor?
Power flow in induction motor
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 15/29
15
Power relations
3 cos 3 cosin L L ph phP V I V I
2
1 13SCLP I R
( ) AG in SCL coreP P P P
2
2 23 RCLP I R
conv AG RCLP P P
( )out conv f w strayP P P P
Equivalent Circuit
• We can rearrange the equivalent circuit as
follows
Actual rotor
resistance
Resistance
equivalent to
mechanical load
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 16/29
16
Power relations - continued
3 cos 3 cosin L L ph phP V I V I
2
1 13SCLP I R
( ) AG in SCL coreP P P P
2
2 23 RCLP I R
conv AG RCLP P P
( )out conv f w strayP P P P
conv RCLP P 2 223
R I
s
2 22
(1 )3 R s I s
RCLP
s
(1 ) RCLP ss
Torque, power and Thevenin’s Theorem
• Thevenin’s theorem can be used to transform the network to the left of
points ‘a’ and ‘b’ into an equivalent voltage source V 1eq in series with
equivalent impedance Req+ jX eq
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 17/29
17
1 1
1 1( )
M eq
M
jX V V
R j X X
1 1( ) // eq eq M
R jX R jX jX
1 1
22
222( )
eq eq
T
eq eq
V V I
Z R R X X
s
Then the power converted to mechanical (Pconv)
2 22
(1 )conv
R sP I
s
and the internal mechanical torque (T conv)
convconv
m
PT
(1 )
conv
s
P
s
2 22
s
R I
s
2
1 2
2
222
1
( )
eq
conv
s
eq eq
V RT
s R R X X
s
2 21
2
222
1
( )
eq
conv
s
eq eq
RV
sT
R R X X
s
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 18/29
18
Torque-speed characteristics
Typical torque-speed characteristics of induction motor
Induction motor torque-speed characteristic curve, showing the extended operating ranges
(braking region and generator region)
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 19/29
19
1. The induced torque of the motor is zero at synchronous speed.
2. The torque- speed curve is nearly linear between no load and full load. In this range, the rotor
resistance is much larger than the rotor reactance, so the rotor current, the rotor magnetic
field, and the induced torque increase linearly with increasing slip.
3. There is a maximum possible torque that cannot be exceeded. This torque, called the pullout
torque or breakdown torque, is 2 to 3 times the rated full load torque of the motor.
4. The starting torque on the motor is slightly larger than its full-load torque, so this motor will
start carrying any load that it can supply at full power.
5. Notice that the torque on the motor for a given slip varies as the square of the applied
voltage.
6. If the rotor of the induction motor is driven faster than synchronous speed, then the direction
of the induced torque in the machine reverses and the machine becomes a generator,
converting mechanical power to electric power.
7. If the motor is turning backward relative to the direction of the magnetic fields, the induced
torque in the machine will stop the machine very rapidly and will try to rotate it in the other
direction. Since reversing the direction of magnetic field rotation is simply a matter of
switching any two stator phases, this fact can be used as a way to very rapidly stop an
induction motor. The act of switching two phases in order to stop the motor very rapidly
is called plugging.
Comments on Torque-Speed Curve
Finding maximum torque
• Maximum torque occurs when the power transferred to R2 / s is
maximum.
• This condition occurs when R2 / s equals the magnitude of the
impedance Req + j ( X eq + X 2)
max
2 222
( )eq eq
T
R R X X
s
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 20/29
20
• The corresponding maximum torque of an induction motor equals
The maximum torque is independent of R2
2
m ax2 2
2
1
2 ( )
eq
s eq eq e q
V T
R R X X
max
2
2 22( )
T
eq eq
Rs
R X X
The slip at maximum torque is directly proportional to the rotor resistance R2
• Rotor resistance can be increased by inserting external resistance only
in the rotor of a wound-rotor induction motor.
• The value of the maximum torque remains unaffected but the speed at
which it occurs can be controlled.
Effect of rotor resistance on torque-speed characteristic
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 21/29
21
Speed Control
There are 3 types of speed control of 3 phase induction machines
a. Varying rotor resistance
b. Varying supply voltage
c. Varying supply voltage and supply frequency
a. Varying rotor resistance
• For wound rotor only
• Speed is decreasing for constant
torque
• Constant maximum torque
• The speed at which max torque
occurs changes
• Disadvantages:
– large speed regulation
– power loss in Rext
– reduce the efficiency
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 22/29
22
• Maximum torque changes
• The speed which at max torque occurs is
constant
• Relatively simple method – uses power
electronics circuit for voltage controller
• Suitable for fan type load
• Disadvantages :
– Large speed regulation since ~ ns
b. Varying supply voltage
• The best method since supply voltage and
supply frequency is varied to keep V / f constant
• Maintain speed regulation
• Uses power electronics circuit for frequency
and voltage controller
• Constant maximum torque
c. Varying supply voltage and supply frequency
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 23/29
23
Above figure illustrates the desired motor characteristic. This figure shows two wound-
rotor motor characteristics, one with high resistance and one with low resistance. At high
slips, the desired motor should behave like the high-resistance wound-rotor motor curve; at
low slips, it should behave like the low-resistance wound-rotor motor curve. Fortunately, itis possible to accomplish just this effect by properly taking advantage of leakage
reactance in induction motor rotor design.
Typical torque-speed
curves for 1800 rpm
general-purpose
induction motors
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 24/29
24
(a) Class A:
large bars near the surface;
(b) Class B:
large, deep rotor bars;
(c) Class C:
double-cage rotor design;
(d) Class D:
small bars near the surface.
Laminations from typical cage
induction motor rotors, showingthe cross section of the rotor
bars:
Ex3.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 25/29
25
Sol.
Ex4.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 26/29
26
Sol.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 27/29
27
Ex5.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 28/29
28
Sol.
7/30/2019 Three Phase Induction Machines-2p
http://slidepdf.com/reader/full/three-phase-induction-machines-2p 29/29