8/9/2019 Safety Tips Wiring Harness
http://slidepdf.com/reader/full/safety-tips-wiring-harness 1/3
1. DO NOT eave g t connecte to a power source w en not n use.
2. DO NOT place light face down on ANY surface. If the light is switched on the intense heat generated may ignite the surfacean cause a me t own o t e amp o y.
3. Ensure a e ectr ca connectors are secure - oose connect ons w generate excess ve eat, amage w r ng an causee ectr ca a ure.
4. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry rag willscratc t e ens, espec a y t e sur ace s usty. NEVER c ean t e g t w t c ean ng u or so vent.
5. DO NOT attempt to c ean t e ns e o t e g t or touc t e ns e ens an re ector.
6. LIGHTFORCE an e g ts may e use n e t er po ar ty as t ey are not eart e v a ous ng.
7. LIGHTFORCE lights are not designed to be used for long periods of time in a stationary position with minimal airow, failure tocomp y w vo warranty. Contact LIGHTFORCE rect to scuss a ternat ve opt ons suc as re uc ng g o e wattage.
8. GLOBE REPLACEMENT: T e Xenop ot® g o e g ves approx mate y 10% greater e c ency t an any ot er Ha ogen g o e osimilar voltage. A number of optional globe strengths are available upon request. For removal, simply:
a Rotate t e re ector ous ng ant -coc w se to sengage t.
Remove o g o e y gr pp ng rm y an pu ng out n t e ong ax s rect on o t e g o e.
DO NOT TOUCH NEW GLOBE WITH FINGERS, use a t ssue or p ast c s eeve. Pr or to nsert ng a new g o e, scrape t eg o e egs w t an a ras ve sur ace san paper or n e e ge to ensure post t ve contact w t t e g o e o er e ectro es.
ii) Position the globe legs rmly into the xed electrodes of the globe holder, applying a rm pressure towards the rear. AVOIDer ng or tw st ng movements. NOTE: G o e can on y e move to t e e t an r g t NOT up an own.
iii) Mere placement of the globe into the globe holder is often not sufcient to give a properly ne tuned beam. The operatorcan overcome t s y a gn ng t e sp t ne a ong t e top o t e rotat on oc ng NIB an t e sp t ne on t e en o t ean e w t t e centre o t e g o e ament. see F g.1
v P ease note: w en tt ng a 12v vert ca ament g o e to your RMSM, eave 3 -4mm c earance etween t e g o e o erp ns an t e ase o t e g o e, t s w a ow opt ma ocus ng a ty. T e 12v 75W vert ca ament g o e s stan ar nRMSM140 & RMS
v A ot er g o e .
v Max mum g o e wattage recommen aton:
140 LANCE: 12V 75W
170 STRIKER: 12V 100W
40 BLITZ: 12V 100W
REDATOR: 12V 30W
NFORCER: 12V 35W
Note: USING GREATER WATTAGE WILL VOID WARRANTY
9. FOCUSING MECHANISM: T e patente ocus mec an sm a ows prec se a ustment o t e eam to var ous concentrat onpatterns as es re . S mp y rotate t e re ector an se ect t e es re SPOT not app ca e or Pre ator & Stu y g tmo e s .
10.S orten ng ca e engt can e respons e or VASTLY s orten ng g o e e.
11.Ensure during use reector surface is not wound too far forward past the globe holder or melting of the housing can occuran w not e covere un er warranty.
12.We recommen w r ng RM g ts w t a m n mum 10 amp w re.
13.LIGHTFORCE AUSTRALIA PTY LTD shall not be liable for damage, malfunction, failure resulting from accident, misapplication,m suse, unaut or se repa r, neg ect, mo cat on, unaut or se or non stan ar rep acement parts, accessor es, g o es,
atter es or vo tage or t e operaton o t e pro uct eyon ts tec n ca an env ronmenta spec cat ons. T e purc aserac now e ges t at oca aws may pro t t e use o some o t e pro uct on motor ve c es trave ng on pu c roa s anagrees t at t s t e r respons ty to ascerta n t e e ect o oca aws.
PERFORMANCE LIGHTING
LIGHTFORCE AUSTRALIA PTY LTD • 28 Orsmond Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: 08 8440 0888 | Fax: 08 8346 0504 • Int’l: Tel: +618 8440 0888 | Fax: +618 8346 0504
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © Oct 2006 • Data and specications contained maybe subject to change without notice.
LIGHTFORCE Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modication, unauthorised or non standard replacement parts,
accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specication.
INSTRUCTION DATA
RODUCT: USE & SAFETY TIPS
VER: 1.0
ATE: OCTOBER 2006
8/9/2019 Safety Tips Wiring Harness
http://slidepdf.com/reader/full/safety-tips-wiring-harness 2/3
8/9/2019 Safety Tips Wiring Harness
http://slidepdf.com/reader/full/safety-tips-wiring-harness 3/3
LIGHTFORCE AUSTRALIA PTY LTD • 28 Orsmond Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: 08 8440 0888 | Fax: 08 8346 0504 • Int’l: Tel: +618 8440 0888 | Fax: +618 8346 0504
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © Oct 2006 • Data and specications contained maybe subject to change without notice.
LIGHTFORCE Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modication, unauthorised or non standard replacement parts,accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specication.
PERFORMANCE LIGHTING
COMPONENT BREAKDOWN
� �
� � �
� � �� � �
� �� � ��
� �
� � �
� � �� �� � �� � � �
� � �
� �
� �
� �
� �
� �
��
�
�
�
��
� ���
� � �� �
� ��
edBlack/R
Brown
Black/Yellow
Black
White
Black
White
Black
Yellow
rown
A
B
C
