1
Owner’s manual
ElectroDrive Lipo Smart Para
and Lipo Smart Tetra
Version 04-2016
Hand over to the customer
always together with the
standard manual
Find an installation Video at
www.stricker-handbikes.de
/installation
2
The device complies with the current standards and directives of the EU. We certify this in the EC declaration
of conformity. If required we will be glad to send you the according declaration of conformity.
Index of Contents
Safety Instructions Please read these safety instructions carefully before the first use: - Before starting, check if the battery is well connected, especially if you have disconnect for
charging
- Before starting, check the function of the brakes
- turn the key switch to “ON”
Attention:
- When you stop „off“ the key switch at the controller case
- If you interrupt riding for a longer time „off“ the switch at the battery (otherwise the
battery will be discharged by itself)
- At disconnecting the bike or move the bike forward and rank, always turn off the motor. If
the bike is unguarded remove the key or
- Put the driving gas to 0 to avoid unintentional driving by moving the crank handle.
If you are not using the battery for a longer time (winter season) store the battery
completely charged and charge again every 4 month to avoid damage of the battery
(deep discharge). - use only our charger
- don’t choose the fastest speed in narrow or busy places
- keep the device out of reach of children especially don’t allow somebody to enter anything into
the battery, risk of explosion or fire
- for loading the electro drive lipo into the car, remove the battery-
- driving uphill: For protecting the system, watch the battery temperature at the display (see page
12) while driving up the hill. The temperature shouldn’t go over 45 degrees Celsius.
1. Speed control and pedelec sensor................................................................................................... 03
1.1 Paraversion..................................................................................................................................... 03
1.2 Tetraversion.................................................................................................................................... 04
2. Operation of the ElectroDrive Lipo Smart...................................................................................... 04
3. Start – Journey – End……………………...................................................................................... 04
3.1 Light switch……………………………....................................................................................... 05
3.2 3-speedswitch…………………………........................................................................................ 05
3.3 LED temperature display of engine temperature........................................................................... 05
4.1 Batteries………………………………………………………………………………………….
4.2 Remove the battery........................................................................................................................
06
08
4.3 Fuse................................................................................................................................................ 09
4.4 Charger and charging of the battery.............................................................................................. 09
4.5 Optional equipment: 2 lipo batteries connected at the fork with 2 switches.................................
4.6 Optional equipment: 2 lipo batteries connected at the fork with 4 switches.................................
4.7 Optional equipment: Lead acid batteries at klickfix connector.....................................................
10
11
12
5. Instruction capacity display............................................................................................................. 13
6. Change of tyres................................................................................................................................. 14
7.0 Error search......................................................................................................................................
7.1 Brake contact…...............................................................................................................................
14
15
8. Technical Facts.................................................................................................................................. 16
9. Shipment…........................................................................................................................................ 16
3
Owner’s manual
1. Speed control and pedelec sensor
1.1 Paraversion
- At the ergo handle there is a thumb throttle for controlling the speed and a brake lever
with interrupter as well as a locking mechanism (picture 1).
- Since 15th of July 2014 there is no brake interrupter installed anymore.
- The brake lever on right has no interrupt and is therefore useful for starting at a slope.
- You can drive with the thumb throttle between 6 to 25 km/h without pedaling
depending on the law of your country. When you start pedaling, the pedelec sensor
perceive it, and then the thumb throttle at the ergo handle will be deactivated. Now
the control at the handhold is controlling the speed (picture 2).
- Furthermore there is a 3speedswitch for a pre-adjustment of the speed (picture 3).
The brake lever on the left side has an electrical interrupt. While using it the electronic is switched
off.
The brake lever on right has no interrupt and is therefore very useful for starting at a slope.
Use always both brake levers for braking.
picture 1: thumb throttle at ergo handle picture 2: control at the handhold
picture 4: pedelec sensor, distance 1-2 mm
4
1.2 Tetraversion
1- speed control for chin operation
2- starting aid button: press one second and the Lipo Smart starts two seconds long
2. Operation of the Lipo Smart
Check if all components are screwed tight. The cables may not disturb the steering and must
be fixed narrow to the frame. No cable may be damaged.
3. Start – Journey - End
Use fully charged battery. Choose a calm place for using the Lipo Smart the first time.
Start:
key switch „on“(picture 5; you can remove the key now to avoid losing it while riding)
Turn the grip throttle for acceleration.
End:
On/Off- switch at the battery “off” (picture 7), key switch at controller case „off“(picture 6)
and remove the key
5
key position:
3.1 Light switch (1)
To on and off the 36V LED lamp.
3.2 3-speedswitch (2)
To adjust the performance and speed limit of the bike. Level 1 (50%), level 2 (75%)
and level 3 (100%) of the maximal engine performance.
3.3 LED temperature display of engine temperature
Since the 1th of june 2015, the control boxes are equipped with a LED temperature display.
If the Lipo Smart has a LED in the control box but is without a temperature sensor in the motor, the
LED has no function.
• Is a coil temperature in the motor (hub) of 150C° reached, the LED lights up.
• If the LED lights up, the speed must be reduced and the manual mode should be increasingly
used.
• If the LED doesn´t stop lightning, the handbike needs to be stopped until the engine has
cooled and the light goes out.
picture 5: on picture 6: off
6
4. Battery, remove the battery, charger and charging of the battery
4.1 Battery
The ElectroDrive Lipo Smart has a maintenance-free 36 Volt Lipo Battery with a capacity of 11,6A.
The battery has no so called memory effect. You can charge all the time.
I.e. no need for totally discharging the battery before charging again.
Attention: The new Lipo Smart models have no fuses.
Batteries are consumables. The warranty is 6 month. Please bring damaged batteries to the labelled
places.
Always turn off at the
Break of journey
battery main switch:
picture 7: off Picture 8: on
7
8
1.
4.2 Removing the battery For removing the battery turn the key counterclockwise and pull the battery from the socket.
Attention!
Make sure that the battery is locked (clockwise) before start riding to avoid the falling down of the
battery (picture 9)
Attention!
Always remove the key while riding, to avoid the reopening of the key by itself.
see charging conditions by pushing
the button
if you switch-off the battery main
switch, the display switches-off, too.
Dreistufenschalter
picture 8 picture 9
picture 7
9
4.3 Fuse
The battery has a fuse, 16 A slow.
Our order number is 630947-0. The new batteries (since 2012) with the
yellow casing don’t have a fuse.
Since 2015 the batteries have a fuse again.
4.4 Charger and charging of the battery
10
4.5 Optional equipment: 2 lipo batteries connected at the fork with 2 switches (no standard battery connector on top)
At the controller case there are 2 dipswitches.
One for switch the batteries from right to left because it’s not allowed to connect the batteries
parallel.
And one for switch the display to the correct battery.
Always switch both switches, i.e. the switches must be always in the same position.
Switch case to switch the batteries (the form could diversify)
battery left on duty battery right on duty
11
4.6 Optional equipment: 2 lipo batteries connected at the fork with 4 switches,
with the possibility to connect one battery on top at
the standard battery connector
At the controller case there are 2 dipswitches.
Ones for switch the batteries from right to left because it’s not allowed to connect the batteries
parallel.
And ones for switch the display to the correct battery.
Furthermore 2 more switches to change from up to down.
battery above on duty battery down left on duty
battery down right on duty
12
4.7 Optional equipment: Lead acid batteries at klickfix connector at the fork additional to lipo battery above with switch from lipo battery to lead
acid battery.
The capacity display is not working while lead acid battery is on duty.
The extra battery comes with an automatic charger 36V/1,4A with following performance:
3 steps charge control for fast an automatic charge
different electric tension for charge and maintenance
charging condition is shown by 3 LED‘s
reverse voltage protection
The charger is made for these batteries. Use only this charger to reach the maximum life span and to
avoid a damage of the battery.
For charging you can remove the batteries or you can keep it on the device.
Remove the plug at the battery and connect the plug from the charger to the battery.
Make sure that the charger is connected with the electric supply network. To charge the
battery completely full it will take approx. 3,5 hours.
If you are not using the battery for a longer time (winter season) store the
batteries completely charged and charge again every 2 month to avoid damage of
the batteries (deep discharge).
Please consider the different capacities at different temperatures: 40°C 102%; 25°C 100%; 0°C 85%; -15°C 65%
The plug at the controller case (see underneath) got modified. Therefore a click connection of the
plug is not possible again. The sense of this is to avoid a damage of the cable while removing the
battery.
13
5. Instruction of the capacity display
14
6. Change of tyres
Before changing the tyre disconnect both connectors (picture 10) by cutting the cable ties open.
Stick it together after the change and fix it with cable ties again (picture 11).
7. Error search
- Display doesn’t shine and engine doesn’t work:
a. Battery switch isn’t on ’ON‘
b. Fuse at the battery is blown
c. Battery is empty
- Display is shining but engine doesn’t start while pedaling
a. raise the speed control
b. key switch is on ’OFF‘
c. brake lever damaged – for testing unplug the connector at the brake lever
d. thumb throttle damaged – check which one, without pedaling the thumb throttle at the
ergo handle activates the engine, while pedaling the control at the handhold controls the
speed
e. the connectors at the engine are disconnected
- Engine power is weak:
a. raise the speed control
b. Battery is empty
picture 10 picture 11
15
7.1 Brake contact
7.1 Schedule
1. Battery-Display (4-pin)
2. Pedelec sensor (3-pin)
3. Thumb trottle/transport holder
(3-pin)
4. Thumb throttle
/Starting aid (3-pin)
5. Light (4-pin)
6. sensor for the brake
(2-Polig)
Sensor is free, no magnetic
contact. Unit should work.
Sensor is activated, unit does
not work. Either is the brake
misplaced, on firmly, the
Bowden cable to tight or
slipped out.
Unloose the Magnet with a
screwdriver and justify it new.
16
8. Technical facts weight: ready to start with battery: 24,5 kg
transport without battery: 22,15 kg
weight without kickstand and battery: 21,7 kg
battery: 1,9 kg
measure: height = 110 cm
breadth = 53 cm
length = 55 cm
weight of driver: 120 kg max.
maximal speed: 25 km/h steeples controllable
depends on the law of the country
maximal uphill grade: 14% (depend on the wheelchair)
maximal cross slope: 5%
drive: electrical hub engine
motor capacity: 250 W continuous power with 36V
reach: 30 km plane area
battery: 36 Volt maintenance-free lipo battery with a capacity of 11,6
A
storage temperature range: +5° to 30° C
discharge temperature range: -20° to 40° C
capacity display: the capacity display is set at the battery
brakes: 1.) mech. disk brake at the front wheel
2.) mech. V-brake at the front wheel
tire size: 20 x 175 /47x409
tire pressure: 3 bar (see max. air pressure at tire)
lightening: front light 36V
speedometer: bike-computer
9. Shipment The Lipo Smart consists of
the Lipo Smart, one battery, one charger
rear light for the wheelchair, long Allen key SW6
one safety fuse 16A slow, owner’s manual
Attention!
During connecting the handbike to the wheelchair, make sure that the clamps are parallel to the
tubes of the wheelchair. Otherwise, the PCV-protection can be damaged.
Before you start riding, please make sure, that the PVC- protection on the clamps are undamaged.
PVC-protection parts are wear parts and taken out from warranty!
If there are damages on the wheelchair tube caused by damaged PVC-protection parts (scratches) we
are not liable.