8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 1/14
Omega DENALITM
Adjustable-Height Desk System
INSTALLATION MANUALVERSION 1.0
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 2/142
BEFORE YOU BEGINPROVIDED:
(19) M6 hexagonal
machine bolts
(10) 5x20 mm
Machine Screws
(4) Foot Caps
(2) Support ArmsRight and Lef
(2) Hex Wrenches (2) Feet
(2) Liing LegsRight and Lef
(1) Crank Handle
(1) Drive ShaRight, lef, and center
(2) CrossbarsIdentical (1) Crank Sha
Identical
(1) Omega table top
R
LR
L
*ruler in inches & millimeters foryour convenience
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 3/14
(1) Keyboard Plaorm Mounng Assembly
(2) Keyboard Plaorm Supports
(2) Carriage bolts
(2) Rubber bumpers
(1) Keyboard Plaorm
(1) Keyboard fence
(6) Spacers
(6) #10 1-1/4” fat head
Phillips screws
(7) #10 5/8” pan head
Phillips screws
(8) M5 20mm pan head
machine screws
ROVIDED FOR KEYBOARD TRAY ASSEMBLY:
STEP 11
STEPS 11 & 14STEP 12
R E A D T H I S CONGRATULATIONS on your purchase o an OmegaDENALI™ adjustable-height desk system! We designedthis product to be as easy as possible to assemble, buti you have any questions during the assembly processplease contact our Customer Care team using theinormation on the back page.
SHOULD you be installing your owntable top on the ELLURE rame, besure to drill pilot holes beore inserting woodscrews. Te wood screws supplied with the ELLUREbase should work with most table tops. It is critical to
pay attention to the available depth for pilot holes so a
not to damage the lamination of the table top surface.
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 4/144
the feet are compatible withboth the right or left leg
ASSEMBLY INSTRUCTIONS
CLEAR a good-sized area to lay out all componentsand assemble the desk. Lay the table top down on the floor,laminate side down. I not on carpet, we recommend
placing a sof blanket down first in order to protect thetable top surace. Make sure the entire area is clear o anyloose screws or debris, to avoid scratching the laminatedsurace. Alternatively, this can all be done on top o anothertable rather than on the floor. Be careul not to slide thetable top while upside-down, to protect the laminate.
THE ELLURE base is designed to work with any table top,though assembly is easiest when using a genuine ELLUREtable top. ELLURE table tops include threaded insert nutsthat remove any conusion as to where to drill, the bit size
to use, or how deep to drill. Tese recessed nuts also extendthe lie o the product, by preventing degradation o thewood fibers rom over-tightening and rom removing andreinstalling wood screws too many times.
1PREPARE FOR ASSEMBLY
FOR THIS STEP:
ATTACH one oot to each lifing leg with our (4) M6
machine bolts provided.
SET the right and lef lifing legs upside down on the table.Ensure they are positioned correctly on the table top,reerring to the diagram below. Te right lifing leg willhave the crank gear housing attached. Insert one end oeach crossbar into the opposing ends o the lifing legs,connecting the two legs together.
2 ATTACH FEET AND SET CROSSBAR
IN LEGS
FOR THIS STEP:
the right lifting leghas the crank shaft
housing module
CAUTION!
R L
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 5/14
ATTACH the lef and right top arms to theirrespective lifing columns using our (4) M6 machinebolts or each top arm. Make sure the top support arms areacing outwards. Do not tighten these bolts all the way.
3 ATTACH ARMS TO LEGS
FOR THIS STEP:
EXTEND the base to the appropriate width, sothat the holes in the base are aligned with the recessed nutson the table top. Secure the base to the table top with theappropriate machine screws. You may now tighten the toparm screws rom Step 3.
4 ATTACH BASE TO TABLE TOP
FOR THIS STEP:
R
R
L
L
R
L
x3
x3
use the smaller hex wrench for tset screws
not provided
the four (4) set screwsare located on the
bottom of the crossbars
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 6/146
INSERT the two rods into the drive shaf. Positionthe drive shaf between the two legs and expand
the drive shaf until the two rods are inserted into theirrespective legs.
5INSERT DRIVE SHAFT
FOR THIS STEP:
1 2
3
aerial view of underside
drive shaft
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 7/14
ATTACH a oot cap to the end o each oot.7 ATTACH FOOT CAPS
FOR THIS STEP:
INSERT the crank shaf into the crank gearhousing on the right leg. Affix the crank shaf to
the top arm using three (3) M6 machine bolts.
6 ATTACH CRANK TO ARM
FOR THIS STEP:
crank gear housingcrank shaft
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 8/148
ATTACH the two oot supports to the undersideo the keyboard platorm using three #10 1-1/4” flathead Phillips screws and three spacers per oot support.Position each set o spacers between the oot support andthe underside o the keyboard platorm. DO NOT placewashers between screw head and foot support.
Position the tube assembly by matching the squaremounting plate to the triangular pattern o recessed holesin the center o the underside o the keyboard platorm.Attach the mounting assembly to the underside o thekeyboard platorm using our #10 5/8” pan head Phillips
8 ASSEMBLE KEYBOARD PLATFORM
FOR THIS STEP:
IN ORDER: WASHER, FOOTREST, SCREW
6x2x
6x
4x
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 9/14
USING eight M5 20mm pan head machinescrews, attach the mounting assembly and platorm tothe underside o the desk. Align the tube assembly bymatching the our holes on each mounting bracket to theour insert nuts on both sides o the Omega cutout.
9 ATTACH KEYBOARD PLATFORM
FOR THIS STEP:
8x
10 CAREFULLY FLIP THE DESK UP
DO NOT drag the tabletop alongside its edges. Doing so may
result in scratches. Insert crank handle into the crank shaf.
FOR THIS STEP:
handle folds outof crank
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 10/1410
TILT the Omega keyboard platorm so that youcan easily access both the top and bottom o the
rear end o the platorm. Using three #10 5/8” pan headPhillips, attach the keyboard ence to the back o theplatorm so that the built-in cable guide is acing up whenthe keyboard platorm is flat.
11 ATTACH KEYBOARD FENCE FOR THIS STEP:
3x
we recommend tilting the
platform up for easier access
align the three holes of the
fence with the three holes on thebottom of the platform. once
alugned, use the pan-head screws
to attach the two together.
once the fence is attached to the
platform, you’re ready to install
the bumpers!
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 11/14
AFTER connecting all the cables and testing that
the desk is working properly, you may want to use thesupplied sel-adhesive cable guides to tidy up the cablesor a cleaner appearance.
13 FINAL TOUCHESFOR THIS STEP:
ATTACH each rubber keyboard bumper tothe keyboard platorm by fitting a carriage bolt
through each o the two slots cut into the platorm so thatthe bolt’s head is flush with the underside o the platorm.Secure each bumper in place by using your hand to twistthe rubber bumper o the bolt over the screw threads.
12 ATTACH RUBBER BUMPERSFOR THIS STEP:
2x 2x
on the bottom of the platform,
put the carriage bolts through
the slots.
twist the rubber bumpers over
the bolts until they are secured
this is what the keyboard
platform should look like from
your perspective after you’re
done.
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 12/1412
THE OMEGA Keyboard Platorm can be set to one o two height positions. By deault, the bar assembly arrives setthe lower position. You can adjust the bar assembly higher by removing the two hex screws rom both ends o the pivbar, and reattaching the bar by inserting those same hex screws through the upper set o holes on the bracket.
o adjust the Omega Keyboard Platorm, simply loosen the central clamp by twisting the rubberized kncounterclockwise. Ten push down on the rear end o the platorm or a steeper angle or push up rom the bottom o platorm or a shallower angle. Once you have the platorm set to the desired position, secure it in place by tightenithe rubberized knob by twisting it clockwise.
Depending on the depth and shape o your keyboard you may want to adjust the rubber bumpers orward or back. do this, simply loosen the rubber bumper, slide it to the desired location, and retighten.
USING THE OMEGA KEYBOARDPLATFORM
OPTIONAL ACCESSORIES
1 2 3
THERMODESK INSURFACE DUALAC POWER SOCKET
THE 3” grommet holes provided in the OMEGA tabletops are ideally sized or accepting the flush-mountedpower socket “nodes.”
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 13/14
WARRANTYTHE THERMODESK ELLURE warranty coverage includes 5 years on table tops, and 2 years on the base. Te ollowilimitations apply:
THIS WARRANTY only covers deects as specified herein and does not include deects or damages attributable improper installation, misuse or normal surace weathering, or deects or damages caused by accidents or fire or othcasualty or Acts o God, or any other causes or occurrences beyond the manuacturer’s control. Te exclusive remedaction provided or the customer hereunder shall be repair, restoration or replacement o the components as are outo be deective.
TABLE TOP: Te replacement o new materials or those as may be deective may result in a color variance in comparisto the originally installed laminates due to slight color or texture changes by laminate manuacturers and is not indicato a deect. iMovR reserves the right to substitute such laminates as are then being manuactured and is only obligatto match color and quality with such products as it is manuacturing at the time o replacement.
THIS WARRANTY is limited to repair, restoration and/or replacement by iMovR o any deective unit provided tmanuacturer: (a) receives a written, axed or emailed notice o claim under this warranty, including sufficiently hiresolution photographs that clearly show the nature o the damage, and (b) within 30 days afer notice o claim, is receipt o the deective unit at its place o business, unless this requirement is waived by iMovR. Te manuacturer warrange or retrieval o the deective product via its carrier-o-choice. In some cases the manuacturer may elect notretrieve the deective component, and may opt to send a replacement product based only on photographic evidence
warrantied deects. I upon receipt and inspection o the returned component it is determined that the damage was ndue to a manuacturing flaw but rather one o the exempted reasons stated above, the costs o shipping the units to arom the manuacturer, plus the cost o the replacement component, shall be charged back to the customer.
LIMITATION OF LIABILITY: IT IS UNDERSTOOD AND AGREED THAT MANUFACTURER’S LIABILIT
WHETHER IN CONTRACT, IN TORT UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWIS
SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF PURCHASE PRICE FOR THE DEFECTIVE ITE
PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR SPECIA
INDIRECT OR CONSEQUENTIAL DAMAGES. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF TH
TRANSACTIONS UNDER THIS AGREEMENT MAY BE BROUGHT BY THE PURCHASER MORE THAN ON
YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.
PREVENTATIVE MAINTENANCE AND CLEANINGAFTER first week o use: ighten down all screws and bolts.
CLEANING THE BASE: Clean the base rame by wiping it down with a microfiber cloth moistened with a standhousehold cleaning solution. Never use solvents or abrasive or corrosive compounds on the rame. Te base shouldcleaned at regular intervals to remove dust and dirt, and inspected or mechanical damage, wear and breaks - worn oparts should be replaced.
CLEANING THE TABLE TOP: All TermoDesk table tops are manuactured with a “3D lamination” process that resuin an extremely durable surace, similar to what is ofen used in hospital environments. As such it can stand up to mocleaning solutions without risk o discoloration or degradation. Anti-bacterial solutions may be used. Always test ncleaning solutions on a less-seen surace first beore using on the entire table top.
TROUBLESHOOTINGIF one side o the Omega Denali is rising up or down but not the other, check that the drive shaf is connected to bolegs.
8/10/2019 Omega Denali Manual
http://slidepdf.com/reader/full/omega-denali-manual 14/14
SPECIFICATIONS
DYNAMIC WEIGHT CAPACITY:
STATIC WEIGHT CAPACTIY:
HEIGHT ADJUSTMENT RANGE:
WIDTH ADJUSTMENT RANGE:
200 lbs.
From 29-¼” to 48-¾”
From 32-½” to 54”
390 lbs.
TRAVEL SPEED:
ADJUSTABLE:
MANUFACTURING ORIGIN:
1 inch per 3 cranks
Manual Crank
Made in China
LAMINATION TYPE:
AVAILABLE SIZES:
Sur(x) 3D
30”x42” | 30”x48” | 30”x60” | 30”x72”
EDGING:
SURFACE RATING:
MANUFACTURING ORIGIN:
Ultra-durable
Ergonomically-contoured “comort edge”
Made in Michigan, USA
C O N T A C T : iMovR
HOURS:PHONE:FAX:EMAIL:LIVE CHAT:
See www.iMovr.com/hours(888) 208-6770 or (425) 999-3550(425) [email protected]
AVAILABLE OPTIONS FROM iMovR
Stowaway Ergonomic Keyboard ray
Single and Dual-Arm LCD Monitor Stands
Grommet-mounted Dual-AC Power Socket
DENALI Base
DENALI Table Top
2
1
3
1
2
3