8/13/2019 Mft II Manual 2
1/35
OXFORD ENGINEERING COLLEGE
(AN ISO 9001: 2000 Certified & NBA Accredited Institution)
Karumandapam, Pirattiyur, Trichy620 009
Department of Mechanical Engineering
L B M NU L
Staff In charge: HoD Mechanical
Hod Civil
SUBJECT Manufacturing technology IISUBJECT CODE ME2258
University Anna university ChennaiRegulation 2009
SEMESTER FourthLAB IN CHARGE S.Senthil kumaran
TECHNICAL ASSISTANTS Duraisamy.mSebastin. s
8/13/2019 Mft II Manual 2
2/35
8/13/2019 Mft II Manual 2
3/35
CONTENTS
Ex.No. Name of the Experiment Page. No.
1. Safety Precaution2. Study of Lathe3. Assembly of FitsLathe4. Lathe tool dynamometer5. Study of Milling machine6. Machining Hexagon from circular workpiece7. Study of Gear hobbing Machine8. Study Of SHAPPER
9. Assembly of Fits Shapper10. Study of DRILLING Machine11. Drilling operation using Drilling machine12. Key way cutting using Slotting machine13. Surface Grinding-14. Cylindrical Grinding15. Study of Tool and Cutter grinder16. Study Of Capstan And Turret Lathe
8/13/2019 Mft II Manual 2
4/35
Ex no : 1
Date
WORK SHOPSAFETY PRECAUTIONS
WORK SHOP - DEFINITION
It is a place where the raw material is converted into
finished product.
In other words it is a place where human efforts,
machines, materials & the tools togather manufacture
product.
SAFETY PRECAUTIONS
Keep your Workshop floor Clean and free from dirts.
Always wear Shoes in the Workshop.
Do not wear rings, wrist watch and bangles in the Workshop.
Wear the proper Workshop dress.
Check the machine conditions before machining.
Do not work without guidance of Workshop Supervisor.
Dont operate a machine whose controls is not surely known
to you.
Do not run or talk in the Workshop.
Avoid unnecessary discussions during work time.
Take first aid treatment immediately in case of any injury.
Use proper Safeguards.
Keep the Cutting and measuring tools separately.Check the fire extinguishers periodically.
Follow the instructions of Staff members.
Maintain discipline.
RESULT
Thus the safety Precautions are observed and followed.
8/13/2019 Mft II Manual 2
5/35
Ex no : 2 STUDY OF LATHE
Date
LATHE
Lathe is a machine, which removes the metal from a piece of
cylindrical work to the required shape &size
TYPES OF LATHE
Engine Lathe
The most common form of lathe, motor driven and comes in large
variety of sizes and shapes.
Bench Lathe
A bench top model usually of low power used to make precision
machine small work pieces.
Tracer Lathe
a lathe that has the ability to follow a template to copy a shape or
contour.
Automatic Lathe
A lathe in which the work piece is automatically feed and removed
without use of an operator. Cutting operations are automatically controlled
by a
sequencer of some form
Turret Lathe
lathe which have multiple tools mounted on turret either attached
to the tailstock or the cross-slide, which allows for quick changes in tooling
and cutting operations.
Computer Controlled Lathe
A highly automated lathe, where both cutting, loading, tool changing,and part unloading are automatically controlled by computer coding.
8/13/2019 Mft II Manual 2
6/35
CENTRE LATHE
8/13/2019 Mft II Manual 2
7/35
BED
It is the base of the machine. On its left side, the head stock is
mounted. A movable casting tail stock is mounted on the right side.
The legs of the bed have to down and grout the lathe.
HEAD STOCK
It consists of a spindle, gears and speed change levers. It is used to
transmit the motion to the job. There are two types of head stock.
1. Belt driven headstock2. Geared headstock
CARRIAGE
Carriage is used to carry a tool bring in contact with rotating
workpiece or to withdraw from such a contact. It operation on bed
ways between the head stock and tail stock.
SADDLE
It is a H shaped part fitted on thelathe bed. There is a hand wheel
to move it on the bed way. Cross slide, compound rest, tool post are
fitted on this saddle.
(a)Cross slideIt is on the upper side of saddle in the from of dove tail. A hand
wheel is provided to drive the cross slide. It the crosswise movement
of the tool (i.e.)Movement of tool towards or away from the operator.
(b)Compound restIt is fitted over the cross slide on a turn table. It permits both parallel
and
Angular movement to cutting tool.
(c) Tool postIt is fitted on the top most part of compound rest. Tool is mounted
on this tool post. Cutting tool is fixed in it with the help of screw.
APRON
8/13/2019 Mft II Manual 2
8/35
It is the hanging part in front of the carriage. It is used for
transmitting power for automatic feed or feed for thread cutting
operation.
TAIL STOCK
It is located at the right end of the lathe bed and it can be positioned
any where in the bed. It is used for supporting lengthy jobs and also
carries tool to carry out operations such as tapping, drilling, reaming.
LATHE OPERATIONS
Turning:
Troduce straight, conical, curved, or grooved workpieces
Facing:
To produce a flat surface at the end of the part or for making face
grooves.
Boring:
To enlarge a hole or cylindrical cavity made by a previous process or
to produce circular internal grooves.
Drilling:
To produce a hole by fixing a drill in the tailstock
Threading:
To produce external or internal threads
Knurling:
To produce a regularly shaped roughness on cylindrical surfaces
8/13/2019 Mft II Manual 2
9/35
ASSEMBLY OF FITS - LATHE
8/13/2019 Mft II Manual 2
10/35
Ex no : 3 ASSEMBLY OF FITS - LATHE
DATE :
AIMTo make the shaft and the hole on given work piece using lathe.
MATERIALS REQUIRED
Dia 45x402 nos of MS rod
TOOLS REQUIRED
1.Chuck key
2. Tool post key
3.Steel rule4.vernier caliper
5.center drill
6.HSS tool drill
7.marker/scriber.
8.Punch & hammer
PROCEDURE
Hold the given piece ( first) in 3 jaw chuck.
Turn the OD and finish it as per the dimentions given in the diagram
Remove the work piece from the lathe.
Hold the second work piece in the 3 jaw chuck.
Hold the drill bit in the center of tail stock
Make a hole in the center face of the work piece by using the drill bit.
Fit the fist ( male ) and second ( female ) work piece as per the diagram given.
RESULT
Thus the shaft and hole is finished and Fit is made as per the dimensions given in
the Drawing using lathe machine.
8/13/2019 Mft II Manual 2
11/35
LATHE TOOL DYNAMOMETER
Depth of cut - 0.1 mm
Job MaterialMild Steel
Sr
no
SPEED THRUST ( Fv)
Ch1
Feed (Fv)
Ch2
Radial (Fv)
Ch3
1
2
3
Depth Of cut0.1 mmSpeed450 rpm
Sr
no
Job Material THRUST ( Fv)
Ch1
Feed (Fv)
Ch2
Radial (Fv)
Ch3
1 Mild Steel
2 Brass
3 Aluminium
8/13/2019 Mft II Manual 2
12/35
Ex no : 4 LATHE TOOL DYNAMOMETER
Date :
AIM
To determine the effet of thrust force on depth of cut, speed, feed on thejob material.
To determine the effect of feed force on depth of cut, speed, feed on job
material.
To determine the effect of radial force on depth of cut, speed, feed on the
job material.
INTRODUCTION
In the maufacturing of various macine components a number of machiningoperations are carried. Hence it is essential to study the metal cutting process for
economical aspects. In short, the tool force measured by tool dynamometer is essentail
tool to analyse the process of metal cutting force.The test result are used to solve floor
problems such as tool performance.
SPECIFICATION
1.Sensing Unit
It consists of cylinder with strain gauges mounted on it.
2.Bridge balancing unit
3.Stain gauges
Resistance350 ohms
Gauge Factor2 +- 1
4.Balance Pot
5.Calibration
PROCEDURE
1. Fix the plan sensing unit of the dynamometer on lather tool.2. Connect force indicator with 230V single phase supply and switch on the supply3. Wait for 5 to 10 miniutes to balance the channels and get zero reading on display
with mount the solid piece in the chuck.
4. Adjust the speed & feed of the lathe machine and start the machine feed andtool feed manually to start cutting and then feed it automatically.
5. The vertical & horizantal radial force on the dynamometer should not exceed thelimits.
6. Note down the reading and change the depth of cut and repeat the sameprocedure.
PRECAUTIONS
8/13/2019 Mft II Manual 2
13/35
1. Zero adjustment must be done2. Do not apply excessive load on the sensing unit.3. To ensure long lift the balance pots must also be operated very carefully.4. Maximum force300 kg.
RESULT
Thus the lathe tool dynamometer is studied and verified.
8/13/2019 Mft II Manual 2
14/35
8/13/2019 Mft II Manual 2
15/35
Ex no : 5
DATE :
STUDY OF COLUMN & KNEE TYPE HORIZANTAL & VERTICAL MILLING MACHINE
AIM
To study the details of universal and vertical milling machine
INTRODUCTION
Milling may be defined as a machining process for removing the excess material
from a work piece with a rotating cutting tool called as milling cutter.
MILLING OPERATION
In general all the milling operation can be grouped into the following types.
(i) Peripheral milling(ii) Face MillingTYPES OF MILLING MACHINE
(a)According to the axis(I) Horizantal milling machine(II) Vertical milling machine
(b)According to the purpose(i) General Purpose Milling Maching(ii) Plain milling machine(iii) Universal Milling machine
(c) Accoring to the production type(i) Planner type milling machine(ii) Beam type milling machine(iii) Arm type milling machine(iv) Hand operated machine(v) Continious Machine(vi) Controlled production milling machine
UNIVERSAL HORIZANTAL MILLING MACHINE
The universal Horizantal milling machine differs from the saddle in two parts, so
that the table can be horizantally controlled.
8/13/2019 Mft II Manual 2
16/35
VERTICAL MILLING MACHINE
The vertical milling machine is very similar to the plain horizantal milling machine
in neutral position. It is of two types (I) Fixed Bed type ( ii) Column Type.
.
Cutting Speed :
The speed of the milling cutter is its perripheral linear speed resulting from rotating and
it is expressed in M/Min
V = Pi xNxD/ 1000 M/Min
Feed
It is defined as the rate with which operation work pieces advances under cutter.
SAFETY MEASUREMENTS
1) Learn to operate control before operating the machine.2) Work piece must be held on the work piece.3) Dont change spindle speed when the machine is running.
RESULT
Thus the details of Column & Knee type ; Horzantal & vertical milling machine are
studied.
8/13/2019 Mft II Manual 2
17/35
MACHINING A HEXAGON FORM A CIRCULAR JOB
8/13/2019 Mft II Manual 2
18/35
8/13/2019 Mft II Manual 2
19/35
8/13/2019 Mft II Manual 2
20/35
EX no : 7 STUDY OF GEAR HOBBING MACHINE
DATE
GEAR HOBBING PROCESS
In gear generating process the gear are formed by machining by means of form
cutter the cutting teeth of the gear have the shape and size of the teeth of gear to be cut.
In generating process the gear teeth are machined as a result of some relative
motion between gear blank and cutter. A cutter of pitch of capable of generating gear
hobbing different number of teeth.
The common generaating process used for cutting teeth are as follows.
GEAR HOBBING
Hobbing is a gear generating process by means of a rotating cutter hob. The hob
resemble a worm with straight and helical thread parallel to the axis.
This will form reach shaped cutting teeth with proper rake and clearance angle of
the holes are either single threaded or multithreaded.
A single threaded hob will complete one revolution for the generation of each
teeth when as threaded the gear cutting with a hob involves the basic motions.
1) Rotation of hob and gear blank2) Radial movement of gear blank3) Down ward feed of job.
RESULT
Thus the study of gear hobbing process is studied.
8/13/2019 Mft II Manual 2
21/35
SURFACE GRINDING USING HORIZANTAL SPINDLE SURFACE GRINDER
8/13/2019 Mft II Manual 2
22/35
EX NO : 8 SURFACE GRINDING USING HORIZANTAL SPINDLE SURFACE GRINDER
DATE :
AIM
To grind accurately the surfaces of rectangular work piece to the given
dimension.
TOOLS REQUIRED
1.Vernier Caliper
2.Dial Gauge3.Slip Gauge
PROCEDURE
1.The job is firmly held on the magnetic chuck of the table in a surface grinding machine
2.Suitable speed and traverse limit of the table is fixed .
3.The machine is switched on.
4.By giving suitable depth of cut, step down the grinding wheel towards the job.
5.the job is ground accurately to 0.01 mm step by step, so as to completely grind all the
four surfaces to the given accuracy and to the given dimensions.
6. The job is removed and checked.
7.The machine is stopped.
RESULT
Thus the given job surfaces is ground on all the four sides to the given accuracy level.
8/13/2019 Mft II Manual 2
23/35
GRINDING A CIRCULAR JOB IN A UNIVERSAL CYLINDRICAL GRINDINGMACHINE
8/13/2019 Mft II Manual 2
24/35
EX NO : 9 GRINDING A CIRCULAR JOB IN A UNIVERSAL CYLINDRICAL GRINDING
DATE MACHINE
AIM
TO grind a cylindrical and tappered cylindrical surface on a given circular rod.
TOOLS REQUIRED
1. Vernier Caliper2. Dial Gauge3. Slip Gauge
PROCEDURE
1.The given job is mounted in between the centers of the work piece holder of
cylindrical grinding machine.
2. The speed of the grinding wheel head and that of work piece is selected andmachine is switched on .
3. To and fro traverse of the work table is fixed.4. The wheel head is brought near to the rotating job.5. Suitable depth of cut is given and traverse motion of the table is performed to
grind the work piece to entire length.
6. Depth of cut is suitabley given for each traverse motion in step by step, so as tocomplete the grinding of the job
7. The required angle to grind the taper as per the calulation(D-d)/2 x J/L x 360/n = angle in degree
8.The table is switched to the required angle and the work piece is ground for the
length of 35 mm from one end to produce the taper on the work piece.
8. The operation is performed step by step, so as to acheive dimensional accuracy of0.01mm.
9. The machine is stopped and the work piece is checked for dimensions andaccuracy.
10.The work piece is then removed from the work head.RESULT
Hence the job is ground for the required shape with the dimensions accuracy of
0.02mm.
8/13/2019 Mft II Manual 2
25/35
KEY WAY BY USING SLOTTING MACHINE
8/13/2019 Mft II Manual 2
26/35
EX NO :10 KEY WAY BY USING SLOTTING MACHINE
DATE :
AIM :
To make a key way in the given hollow cylindrical work piece.
MATERIAL REQURED
Cylindrical work piece.
TOOLS REQUIRED
1.Scriber
2.Punch
3.Hammer
4. Slotting tool
5.Steel Rule
6.Bolt and nut for holding
7.Spanner set.
PROCEDURE
1.Hold the work piece on the table by using bolt and nut.
2.Set the tool in the tool post.
3.Arrange for slotting movement.
4.Give 0.1 mm depth of cut.
5.Finish to dimensions
6.Switch of the machine
7.Check the work piece for dimensions.
RESULT
Thus the Key way is machined in the given hollow cylindrical work piece by using
slotting machine.
8/13/2019 Mft II Manual 2
27/35
CRANK AND SLOTTED LINK MECHANISM
8/13/2019 Mft II Manual 2
28/35
Ex no : 11 STUDY OF SHAPING MACHINE
Date
Aim
To Study the Quick return mechanism in shaping machine
Crank and slotted link mechanism
The crank and slotted link mechanism is shown in fig. The motion or power is transmitted
to the bull gear through a pinion which receives its motion from An individual motor or
over head line shaft through speed control mechanism. Speed of bull gear may be
changed by different combination of gearing or by simply shifting the the belt on the
step cone pulley.
Bull gear is the large gear mounted with in the column. Bolted to the centre of the bull
gear is a radial slide which carries a sliding block into which the crank pin is fitted.
Rotation of the bull gear will cause the crank pin to revolve a t a uniform speed.
Sliding block which is mounted upon the crank pin is fitted with in the slotted link. The
slotted link which is also known as the rocker arm is pivoted at its bottom end attached
the frame of the column. The upper end of the rocker arm is forked and connected to
the ram block 8 by a pin.
As the bull gear rotates causing the crank pin to rotate, the sliding block fastened to the
crank pin will rotate on the crank pin circle and at the same time will move up and down
the slot in the slotted link giving it a rocking movement which is communicated to the
ram. Thus the rotary motion of the bull gear is converted to receiprocating movement
of the ram.
Result
Thus the crank and slotted link mechanism in shaper is
studied.
8/13/2019 Mft II Manual 2
29/35
ASSEMBLY OF FITS- SHAPING
8/13/2019 Mft II Manual 2
30/35
8/13/2019 Mft II Manual 2
31/35
8/13/2019 Mft II Manual 2
32/35
EX NO13 STUDY OF TOOL AND CUTTER GRINDER
DATE
AIM
To study the tool and cutter grinder.
A universal tool and cutter grinder is used to sharpen the Reamers, Taps, Single point
cutting tool, milling cutters, dies and punches.
MAIN PARTS OF MACHINE
BASE
It supports all the other parts of the machine . The body and frame are in one unit . the
driving and feed mechanism are fitted to the body.
SADDLE
It is on the top of the body. It carries the table . And ot provides the transverse and ctross
wise movement to the table.
COLUMN
It is on the base of the machine and it carries the wheel head, which moves up and down
for the depth of cut.
Wheel Head
It has two grinding wheels on both ends of the spindle and can be swivelled to the
requirement angle ( 360 degree)
WORK HEAD
It is a seperate part and is fitted on the table for cylindrical works. It is drivebn by a
seperate motor fitted with the work head. It moves along the table and can be swievelled
to any angle ( 180 Degree)
8/13/2019 Mft II Manual 2
33/35
SPECIFICATION
1. Maximum Diameter of the wheel that can be held in the spindle.2.
Maximum height of the job that can be ground.
3. Maximum length of the job that can be ground.4. Maximum breath of the job that can be ground.5. Types of drive ( hydraulic & electrical)6. Number of attachment.
RESULT
Thus the tool and cutter grinder is studied.
8/13/2019 Mft II Manual 2
34/35
MACHINE THE COMPONENT AS PER DRAWING BY USING
SENSITIVE DRILLING MACHINE.
8/13/2019 Mft II Manual 2
35/35
Ex No : 14
Date :
MACHINING THE COMPONENT USING SENSITIVE DRILLING MACHINE
Aim :
To machine the given component as per given drawing using sensitive
drilling machine.
Tools Required:
Sensitive drilling machine
Drill Bit061 no
Drill10 - 1 no
Steel rule1 no
Scriber1 no
Machine vice1 no
Packing plates and blocks.
PROCEDURE
1.