Design of Joint S K Mondals Chapter 1
1. Design of Joint
Theory at a glance (IES, IAS, GATE & PSU)
Cotters In machinery, the general term shaft refers to a member, usually of circular cross-
section, which supports gears, sprockets, wheels, rotors, etc., and which is subjected to torsion and to transverse or axial loads acting singly or in combination.
An axle is a non-rotating member that supports wheels, pulleys, and carries no torque.
A spindle is a short shaft. Terms such as line-shaft, head-shaft, stub shaft, transmission shaft, countershaft, and flexible shaft are names associated with special usage.
A cotter is a flat wedge-shaped piece of steel as shown in figure below. This is used to connect rigidly two rods which transmit motion in the axial direction, without rotation. These joints may be subjected to tensile or compressive forces along the axes of the rods. Examples of cotter joint connections are: connection of piston rod to the crosshead of a steam engine, valve rod and its stem etc.
Figure- A typical cotter with a taper on one side only
A typical cotter joint is as shown in figure below. One of the rods has a socket end into which the other rod is inserted and the cotter is driven into a slot, made in both the socket and the rod. The cotter tapers in width (usually 1:24) on one side only and when this is driven in, the rod is forced into the socket. However, if the taper is provided on both the edges it must be less than the sum of the friction angles for both the edges to make it self locking i.e. + < +1 2 1 2 where 1 2, are the angles of taper on the rod edge and socket edge of the cotter respectively and 1 2, are the corresponding angles of friction. This also means that if taper is given on
Page 1 of 263
Design of Joint S K Mondals Chapter 1
one side only then < +1 2 for self locking. Clearances between the cotter and slots in the rod end and socket allows the driven cotter to draw together the two parts of the joint until the socket end comes in contact with the cotter on the rod end.
t
3d 1d 2dd
Figure- Cross-sectional views of a typical cotter joint
Figure- An isometric view of a typical cotter joint
Design of a cotter joint If the allowable stresses in tension, compression and shear for the socket, rod and cotter be
,t c and respectively, assuming that they are all made of the same material, we may write the following failure criteria:
1. Tension failure of rod at diameter d
=24 t
d P
Fig. Tension failure of the rod
Page 2 of 263
Design of Joint S K Mondals Chapter 1
2. Tension failure of rod across slot
=
21 14 t
d d t P
Fig. Tension failure of rod across slot
3. Tensile failure of socket across slot
( ) ( ) = 2 22 1 2 14 td d d d t P
Fig. Tensile failure of socket across slot
4. Shear failure of cotter
=2bt P
Fig. Shear failure of cotter
5. Shear failure of rod end
=1 12l d P
Fig. Shear failure of rod end
6. Shear failure of socket end ( ) =3 12l d d P
Fig. Shear failure of socket end
Page 3 of 263
Design of Joint S K Mondals Chapter 1
7. Crushing failure of rod or cotter
=1 cd t P
Fig. Crushing failure of rod or cotter
8. Crushing failure of socket or rod ( ) =3 1 cd d t P
Fig. Crushing failure of socket or rod
9. Crushing failure of collar
( ) =2 24 14 cd d P
Fig. Crushing failure of collar
10. Shear failure of collar
=1 1d t P
Fig. Shear failure of collar
Cotters may bend when driven into position. When this occurs, the bending moment cannot be correctly estimated since the pressure distribution is not known. However, if we assume a triangular pressure distribution over the rod, as shown in figure below, we may approximate the loading as shown in figure below.
Page 4 of 263
Design of Joint S K Mondals Chapter 1
Figure-Bending of the cotter
This gives maximum bending moment = +
3 1 1
2 6 4d d dP and
The bending stress, ( ) + + = =
3 1 3 11 1
3 2
32 6 4 2 6 4
12b
d d d dd dP b P
tb tb
Tightening of cotter introduces initial stresses which are again difficult to estimate. Sometimes therefore it is necessary to use empirical proportions to design the joint. Some typical proportions are given below:
A design based on empirical relation may be checked using the formulae based on failure Mechanisms. Question: Design a typical cotter joint to transmit a load of 50 kN in tension or compression.
Consider that the rod, socket and cotter are all made of a material with the following allowable stresses:
Allowable tensile stress ( y )= 150 MPa
Allowable crushing stress (c) = 110 MPa
Allowable shear stress (y) = 110 MPa.
Answer: Refer to figures
d1 = 1.21.d d4 = 1.5.d
l = l1 = 0.75d
d2 = 1.75.d
t = 0.31d
t1 = 0.45d
d3 = 2.4 d
b = 1.6d
c = clearance
Page 5 of 263
Design of Joint S K Mondals Chapter 1
t
3d 1d 2dd
Axial load ( ) = 24 yP d . On substitution this gives d=20 mm. In general Standard shaft size in mm is 6 mm to 22 mm diameter 2 mm in increment 25 mm to 60 mm diameter 5 mm in increment 60 mm to 110 mm diameter 10 mm in increment 110 mm to 140 mm diameter 15 mm in increment 140 mm to 160 mm diameter 20 mm in increment 500 mm to 600 mm diameter 30 mm in increment We therefore choose a suitable rod size to be 25 mm. Refer to figure
For tension failure across slot =
214 y
d d t P . This gives
d1t = 1.58x10-4m2. From empirical relations we may take t=0.4d i.e. 10 mm and this gives d1= 15.8 mm. Maintaining the proportion let d1= 1.2 d = 30 mm.
Refer to figure
The tensile failure of socket across slot ( ) = 2 22 1 2 14 y
d d d d t P
This gives d2 = 37 mm. Let d2 = 40 mm Refer to figure above For shear failure of cotter 2bt = P. On substitution this gives b = 22.72 mm. Let b = 25 mm. Refer to figure For shear failure of rod end 2l1d1 = P and this gives l1 = 7.57 mm. Let l1 = 10 mm. Refer to figure For shear failure of socket end 2l(d2-d1) = P and this gives l = 22.72 mm. Let l = 25 mm.
Page 6 of 263
Design of Joint S K Mondals Chapter 1
Refer to figure For crushing failure of socket or rod (d3-d1)tc = P. This gives d3 = 75.5 mm. Let d3 = 77 mm.
Refer to figure
For crushing failure of collar ( ) =2 24 14 cd d P . On substitution this gives d4 = 38.4 mm. Let d4 = 40 mm. Refer to figure For shear failure of collar d1t1 = P which gives t1 = 4.8 mm. Let t1 = 5 mm. Therefore the final chosen values of dimensions are d = 25 mm; d1 = 30 mm; d2 = 40 mm; d3 = 77 mm; d4 = 40 mm; t = 10 mm; t1 = 5 mm; l = 25 mm; l1 = 10 mm; b = 27 mm.
Knuckle Joint A knuckle joint (as shown in figure below) is used to connect two rods under tensile load. This joint permits angular misalignment of the rods and may take compressive load if it is guided.
d
2t
3d2d
1d
t1t
1t 2td
Figure- A typical knuckle joint
These joints are used for different types of connections e.g. tie rods, tension links in bridge structure. In this, one of the rods has an eye at the rod end and the other one is forked with eyes at both the legs. A pin (knuckle pin) is inserted through the rod-end eye and fork-end eyes and is secured by a collar and a split pin. Normally, empirical relations are available to find different dimensions of the joint and they are safe from design point of view. The proportions are given in the figure above. d = diameter of rod
d1 = d t = 1.25d
d2 = 2d t1 = 0.75d d3 = 1.5.d t2 = 0.5d
Mean diameter of the split pin = 0.25 d
Page 7 of 263
Design of Joint S K Mondals Chapter 1
However, failures analysis may be carried out for checking. The analyses are shown below assuming the same materials for the rods and pins and the yield stresses in tension, compression and shear are given by t, c and . 1. Failure of rod in tension:
=24 t
d P 2. Failure of knuckle pin in double sheer:
=212 4 d P 3. Failure of knuckle pin in bending (if the pin is loose in the fork)
Assuming a triangular pressure distribution on the pin, the loading on the pin is shown in figure below.
Equating the maximum bending stress to tensile or compressive yield stress we have
+ =1
31
163 4
t
t tP
d
Figure- Bending of a knuckle pin
4. Failure of rod eye in shear:
(d2 - d1) t = P 5. Failure of rod eye in crushing:
d1tc = P 6. Failure of rod eye in tension:
(d2 - d1)tt = P 7. Failure of forked end in shear:
2(d2 - d1)t1 = P
Page 8 of 263
Design of Joint S K Mondals Chapter 1
8. Failure of forked end in tension: 2(d2 - d1)t1t = P
9. Failure of forked end in crushing:
2d1t1c = P The design may be carried out using the empirical proportions and then the analytical relations may be used as checks.
For example using the 2nd equation we have = 212Pd
. We may now put value of d1 from
empirical relation and then find FACTOR OF SAFTEY, (F.S.) =
y which should be more
than one. Q. Two mild steel rods are connected by a knuckle joint to transmit an axial
force of 100 kN. Design the joint completely assuming the working stresses for both the pin and rod materials to be 100 MPa in tension, 65 MPa in shear and 150 MPa in crushing.
d
2t
3d2d
1d
t1t
1t 2t
d
Refer to figure above
For failure of rod in tension, = 24 y
P d . On substituting P = 100 kN, y = 100 MPa we have d= 35.6 mm. Let us choose the rod diameter d = 40 mm which is the next standard size.
We may now use the empirical relations to find the necessary dimensions and then check the failure criteria.
d1= 40 mm t= 50 mm d2 = 80 mm t1= 30 mm; d3 = 60 mm t2= 20 mm; Split pin diameter = 0.25 d1 = 10 mm To check the failure modes:
Page 9 of 263
Design of Joint S K Mondals Chapter 1
1. Failure of knuckle pin in shear: =
212 4 y
P d ,which gives y = 39.8
MPa. This is less than the yield shear stress.
2. For failure of knuckle pin in bending:
+ =1
31
163 4
y
t tP
d. On substitution
this gives y = 179 MPa which is more than the allowable tensile yield stress of 100 MPa. We therefore increase the knuckle pin diameter to 55 mm which gives y = 69 MPa that is well within the tensile yield stress.
3. For failure of rod eye in shear: (d2 - d1)t = P. On substitution d1 = 55mm = 80
MPa which exceeds the yield shear stress of 65 MPa. So d2 should be at least 85.8 mm. Let d2 be 90 mm.
4. for failure of rod eye in crushing: d1 t c = P which gives c = 36.36 MPa that is
well within the crushing strength of 150 MPa.
5. Failure of rod eye in tension: (d2 - d1)tt = P. Tensile stress developed at the rod eye is then t = 57.14 MPa which is safe.
6. Failure of forked end in shear: 2(d2-d1)t1 = P. Thus shear stress developed in
the forked end is = 47.61 MPa which is safe.
7. Failure of forked end in tension: 2(d2 -d1)t1y = P. Tensile strength developed in the forked end is then y= 47.61 MPa which is safe.
8. Failure of forked end in crushing: 2d1t1c = P which gives the crushing stress
developed in the forked end as c = 42 MPa. This is well within the crushing strength of 150 MPa.
Therefore the final chosen values of dimensions are:
d1 = 55 mm t = 50 mm d2 = 90 mm t1= 30 mm; and d = 40 mm d3 = 60 mm t2= 20 mm;
Keys In the assembly of pulley, key and shaft, Key is made the Weakest so that it is cheap and easy to replace in case of failure.
Page 10 of 263
S K M
Frogrem
Rectan
1. Repro
Wh
The
Monda
Figure- (a) Sounded; alsib head. (dectangular
metric sizes.
ngular ctangular
oportions of
Width Thickn
here d = Diae key has ta
als
Square or rso available d) Woodrufkey; = hu (f) Tapered
and sq sunk key: this key are
of key, (w)ness of key
ameter of thaper 1 in 1
Des
rectangular with both ff key; als
ub length, hd gib-head k
quare ke: A rectangue:
) y, (t)
he shaft or d00 on the to
sign o
key. (b) Sqends round
so availableh = height; tkey; dimensi
ey ular sunk k
= d / 4 = 2w / 3 =
diameter of top side only
of Join
quare or reded. (c) Sque with flattaper is 18 ions and tap
key is shown
d / 6
the hole in t.
nt
ectangular kuare or rectattened bott in for 12 inper same as
n in figure
the hub.
Chapte
key with onangular keytom. (e) Tan or 1 for 1s in (e).
below. The
er 1
ne end y with apered 100 for
usual
Page 11 of 263
S
2.ke
3.isan
Th
If
o Q
So
S K Mo
. Square suey is that it
. Gib-head usually prnd its use in
he usual proWT
f a square ke
8x
Torld
=Q. A heat
50 mmSelect a
olution: Cofigure b
ondal
unk key: Ts width and
key: It is a
rovided to fan shown in f
oportions ofWidth, (wThicknes
ey of sides d
2Td
[W
treated stm. The shaf
an approp
onsider a rebelow. The k
s Figu
The only diffd thickness a
a rectangulaacilitate thefigure below
f the gib heaw) ss at larg
d/4 is used t
here x the
teel shaft oft rotates
priate key f
ectangular key may fail
Desig
ure-. Rectan
ference betware equal, i.
w = t = d / 4
ar sunk keye removal o
w.
Figure- Gi
ad key are:
ge end, (
then. In tha
4d l
yield is stre
of tensile yat 1000 rpfor the gea
key of widtl (a) in shea
gn of ngular sunk
ween a rect.e.
4
y with a heaof key. A gib
ib-head key
= d t ) =2w
t case, for s
=2xd T
ess in shear
yield strenpm and trar.
th (w), thickr or (b) in cr
Joint
k key.
angular sun
ad at one enb head key
.
/ 4 w / 3 = d /
hear failure
and l is the
gth of 350 ansmits 10
kness (t) anrushing.
C
nk key and
nd known a is shown i
/ 6
e we have
e key length
MPa has a00 kW thr
nd length (L
Chapter
a square su
as gib headn figure be
h.]
a diameterrough a ge
L) as shown
r 1
unk
d. It low
r of ear.
n in
Page 12 of 263
S K M
Sh
Wh
N bandyie4 m
Cru
Flat ke A flat keyfriction fortight fit. T
Saddle A saddle is concaveused for hstress conc
Tange
Monda
ear failure
here torque
being in rpmd y is the yld stress an
m2.
ushing fail
ey y, as shownr the grip. T
Theses keys
e key key, showne to fit the sheavy loads.centration o
ent Key
als
e: The failu
e transmit
m, w, L and yield stress ind substitut
lure c=
n in figure bThe sides o have about
Flat key
n in figure ashaft surfac A simple p
occurs in the
Des
Figure
ure criterio
tted is, (T d are the win shear of ting the valu
2 2ct L d
below is useof these keyt half the th
above, is vece. These kepin can be ue shaft in th
sign o
on is =
) =T Powewidth, lengththe key matues in above
d
ed for lighys are paralickness of s
ry similar teys also havused as a kehese cases. T
of Join
y w L
2/60
Ner
h and diamterial. Takine equations
t load becallel but the unk keys.
Saddle
to a flat keyve friction gey to transmThis is show
nt
2d
N
eter of the sng y to be h and we hav
ause they de top is sligh
e key
y except thagrip and thmit large town in figure
Chapte
shaft respechalf of the tve wL = 2.19
epend entirhtly tapered
at the bottomerefore cann
orques. Verye above.
er 1
ctively tensile 9 x 10-
rely on d for a
m side not be y little
Page 13 of 263
S
F A to
W A shkeusde
T
S K Mo
Feather feather key
o the hub or
Woodru woodruff hown in figueyway is cused in machepth.
he main ad
ondal
key y is used wh the shaft a
uff key f key is a foure below. I
ut in the shhine tools a
dvantages
s
hen one comand the keyw
form of sunkIt is usuallyaft using a and automo
of a wood
Desig
Figure- T
mponent slidway usually
Figure- f
k key whery used for s milling cutobiles due t
Figure- W
ruff key ar
gn of
Tangent Key
des over anoy has a slidin
feather key
re the key sshafts less ttter, as shoto the extra
Woodruff key
re as follow
Joint
other. The kng fit.
shape is thathan about wn in the fa advantag
y
ws:
C
key may be f
at of a trun 60 mm diafigure belowge derived f
Chapter
fastened eit
ncated disc,ameter and w. It is widfrom the ex
r 1
her
, as the
dely xtra
Page 14 of 263
Design of Joint S K Mondals Chapter 1
1. It accommodates itself to any taper in the hub or boss of the mating piece. 2. It is useful on tapering shaft ends. Its extra depth in the shaft prevents any tendency to turn over in its keyway.
The main dis-advantages of a woodruff key are as follows: 1. The depth of the keyway weakens the shaft. 2. It can not be used as a feather.
Circular (Pin) Keys
Significantly lower stress concentration factors result from this type of key as compared to parallel or tapered keys. A ball end mill can be used to make the circular key seat.
Splines Splines are essentially stub by gear teeth formed on the outside of the shaft and on the inside of the hub of the load-transmitting component. Splines are generally much more expensive to manufacture than keys, and are usually not necessary for simple torque transmission. They are typically used to transfer high torques. One feature of a spline is that it can be made with a reasonably loose slip fit to allow for large axial motion between the shaft and component while still transmitting torque. This is useful for connecting two shafts where relative motion between them is common, such as in connecting a power takeoff (PTO) shaft of a tractor to an implement. Stress concentration factors are greatest where the spline ends and blends into the shaft, but are generally quite moderate.
Page 15 of 263
S
S K Mo
ondal
s Desig
gn of
Joint
Splines caas a skeyways keys mashaft.
There areof splinindustry: splines, asplines.
Splines puniform transfer oshaft than
C
an be thougeries of
with machined on
two major nes used 1) straight-and 2) inv
provide a circumfere
of torque tn a key.
Chapter
ght of axial
mating nto a
types in -sided volute
more ential o the
r 1
Page 16 of 263
Design of Joint S K Mondals Chapter 1
Spline Manufacturing Methods Splines are either cut (machined) or rolled. Rolled splines are stronger than cut splines due to the cold working of the metal. Nitriding is common to achieve very hard surfaces which reduce wear.
Welded joints A welded joint is a permanent joint which is obtained by the fusion of the edges of the two parts to be joined together, with or without the application of pressure and a filler material. The heat required for the fusion of the material may be obtained by burning of gas (in case of gas welding) or by an electric arc (in case of electric arc welding). The latter method is extensively used because of greater speed of welding. Welding is extensively used in fabrication as an alternative method for casting or forging and as a replacement for bolted and riveted joints. It is also used as a repair medium e.g. to reunite metal at a crack, to build up a small part that has broken off such as gear tooth or to repair a worn surface such as a bearing surface.
Types of welded joints: Welded joints are primarily of two kinds: (a) Lap or fillet joint Obtained by overlapping the plates and welding their edges. The fillet joints may be single transverse fillet, double transverse fillet or parallel fillet joints (see figure below).
Page 17 of 263
S
(b
Th
S K Mo
b) Butt Formed b(for thickbutt joint Squar Single Single Single Single
hese are sch
ondal
Joints by placing tk plates) on ts may be of re butt jointe V-butt joine U-butt joine J-butt joine bevel-butt
hematically
s
Figur
the plates e the edges bf different tyt nt, double Vnt, double Unt, double J- joint, doub
shown in fi
Desig
re- Different
dge to edgebefore weldypes, e.g.
V-butt joint U-butt joint -butt joint le bevel but
igure below
gn of
t types of la
e and weldinding. Accord
tt joint.
Joint
ap joints
ng them. Gding to the
C
Grooves are shape of th
Chapter
sometimes he grooves,
r 1
cut the
Page 18 of 263
S K M
There are
Cor Edg T-jo
Weldin A welding
1. R 2. A 3. B 4. D 5. S 6. F 7. T 8. S These wel
Monda
e other typrner joint (sge or seal jooint (see fig
ng sym symbol has
Reference liArrow. Basic weld sDimensions SupplementFinish symbTail. Specification
ding symbo
als
pes of weldsee figure beoint ( see figgure below)
mbol s following b
ne.
symbols (lik tary symbolbols
n processes
ls are place
Des
Figure- Dif
ded joints, elow) gure below)
basic elemen
ke fillet, but
s.
ed in standa
sign o
fferent types
for examp
nts:
t joints etc.)
ard locations
of Join
s of butt join
ple,
)
s (see figure
nt
nts
e below)
Chapte
er 1
Page 19 of 263
S
Ew
D Thbu
W
Fo(s
S K Mo
xample: If with convex c
Design he main faiutt joint is
Where t = t =th l =len
or a square see figure be
ondal
the desiredcontour, the
of a builure mecha
allowable thickness of tngth of the butt joint t
elow).
s
d weld is a fe weld symb
utt joint nism of wel
ensile strenthe weld weld. t is equal to
Desig
fillet weld ofbol will be a
Figure-
lded butt jo
=Pngth of the w
o the thickn
gn of
f size 10 mms following
Tee joint
int is tensil
At t weld materi
ness of the p
Joint
m to be don
le failure. T
al.
plates. In ge
C
e on each si
Therefore th
eneral, this
Chapter
ide of Tee jo
e strength o
need not be
r 1
oint
of a
e so
Page 20 of 263
S K M
Design Consider athe weld mload P acta fillet we
throat is e
transverse
Where s Athroat = thFor a doub
Design Consider ato see fromarea (try t
throat are
Monda
n of traa single tranmetal is verys as shear fld. If the fil
easily seen t
e fillet weld
= allowablehroat area. ble transver
n of paa parallel film the strengto prove it).
a =2t
lhA . T
als
ansversnsverse joiny complicatforce on thellet weld ha
to be2
hl . W
is
e shear stres
rse fillet join
Figu
rallel fillet weld as gth of mater. The allow
The total all
Des
Figu
se fillet nt as showned. In desig
e throat areaas equal bas
With the abo
P = ss
nt the allow
ure- Enlarg
llet join shown in firial approacable load ca
lowable load
sign o
ure- butt joint
joint n in figure bgn, a simplea, which is se and heigh
ove conside
s .Athroa
wable load is
e view of fil
nt igure belowch that the married by ea
d is P = 2 s
of Join
t
below. The g procedure the smallesht, (h, say),
ration the p
at
s twice that
llet welding
. Each weldmaximum sach of the j
s At.
nt
general streis used assu
st area of th then the cr
permissible
of the singl
d carries a loshear occursoint is s
Chapte
ess distributuming that he cross sectross section
load carrie
le fillet joint
oad 2P . It is along the tA , whe
er 1
tion in entire tion in of the
d by a
t.
is easy throat
ere the
Page 21 of 263
S
Inabfig
W
D Cbeasdito
W
S K Mo
n designing bove designgure below)
Where
Design onsider a celow. If the s in paralleiameter of torque the m
Where
ondal
a weld joinn criteria. W
the allowab
At tA = throa
of circucircular sha shaft is subel fillet jointhe shaft, thaximum she
T =d = outer d
throatt = t
pJ = polar
= 32
s
nt the desigWhen a comb
ble load is
= throat arat area alon
ular filleaft connectebjected to a
nt. Assuminhe maximumear stress in
max == torque appdiameter of throat thicknr moment of
( + throat2td
Desig
gn variablesbination of t
2 sP =rea along th
ng the trans
Figure et weld
ed to a plata torque, sheng that the m shear strn the weld i
2p
dT t
J
+=plied. f the shaft ness f area of the
) 4 4d
gn of
are h and transverse
s t s tA A + he longitudiverse direct
d subjecte by meansear stress d weld thickress occurs is
throat
p
t
e throat sect
Joint
l. They canand paralle
nal directiotion.
cted to s of a fillet develops in tkness is verin the throa
tion.
C
n be selectedel filled join
n.
torsion joint as shthe weld inry small comat area. Th
Chapter
d based on t required (
n hown in fig
n a similar wmpared to us, for a giv
r 1
the (see
gure way the ven
Page 22 of 263
S K M
When tht
The throat
Q. A plmeathe l
Solution.
a loa
= thr
2556 1
allow(Note
Q. Two
tranthe s
Solution:
assumspeciMPaweld
Monda
hroat ,d
t dimension
late 50 mmns of paralength of th
In a parallad of 50 k
2P =
roat length =3
310 2 5012.5 10
=wance for ste that the a
plates 20nsverse welsize of the
According ming maximified the she. Assuming is calculate
als
=max4
n and hence
m wide anallel fillet whe weld. A
lel fillet welkN 25kN= .
12.52
mm= . S
0.5mm . How
tarting or sllowance ha
00 mm wilds at the weld assum
to the desimum shear ear strength there are twed from
35 Or l
Des
=3
2
throat
dT
t d weld dimen
2throa
Tt
nd 12.5 mmwelds. The
Assume allo
lding two linMaximum s
Since splt
=
wever some
stopping of as no connec
ide and 10ends. If thming the a
gn principle stress occuh may be cawo welds, e
3 110 l = = 141.42 m
sign o
=2
throat
Tt d
nsion can be
m2at
Td
=
Fig.
m thick is e plates areowable she
nes of weldishear stress
656 10= . H
e extra len
the bead. Action with th
0 mm thiche plates arallowable t
e of fillet (turs along thalculated as
each weld ca
310 10 32
mm.
of Join
2d
e selected fr
max
to be wee subjectedear strengt
ing are to bs in the par
Hence the mi
ngth of the
A usual allhe plate thi
ck are to re subjectetensile stre
ransverse) he throat ars half of tenarries a load
635 10
nt
rom the equ
lded to and to a loadth to be 56
be provided.rallel fillet w
inimum len
weld is to
owance of ickness)
be weldeed to a loaess 70 MPa
joint the wrea. Since tensile strengd of 35 kN a
Chapte
ation
nother plad of 50 kN. MPa.
Each line sweld is p
lt, w
ngth of the w
o be provid
12.5 mm is
d by meaad of 70 kNa.
eld is desensile stren
gth, i.e. , sand the size
er 1
ate by . Find
shares where t
weld is
ded as
s kept.
ans of N, find
signed ngth is = 35 of the
Page 23 of 263
Design of Joint S K Mondals Chapter 1
Adding an allowance of 12.5 mm for stopping and starting of the bead, the length of the weld should be 154 mm.
Q. A 50 mm diameter solid shaft is to be welded to a flat plate and is required to
carry a torque of 1500 Nm. If fillet joint is used foe welding what will be the minimum size of the weld when working shear stress is 56 MPa.
Solution. According to the procedure for calculating strength in the weld joint,
= sthroatT
t d22
Where the symbols have usual significance. For given data, the throat thickness is 6.8 mm. Assuming equal base and height of the fillet the minimum size is 9.6 mm. Therefore a fillet weld of size 10 mm will have to be used.
Q. A strap of mild steel is welded to a plate as shown in the following figure.
Check whether the weld size is safe or not when the joint is subjected to completely reversed load of 5 kN.
Fig.
Solution. As shown in the figure the joint is a parallel fillet joint with leg size as 9 mm and
the welding is done on both sides of the strap. Hence the total weld length is 2(50) = 100 mm.
In order to calculate the design stress the following data are used
k1 = 2.7 (parallel fillet joint, refer table 3) (there is required a table to solve the problem)
w = 0.9 cm K = -1 for completely reversed loading The value of the allowable fatigue stress (assuming the weld to be a line) is then
1358 0.9 214.8 kgf/cm = 214800N/m
1.5 = = (approx).The design stress is Therefore
Page 24 of 263
S K M =1, 2142.dfluctuating
Thread Bothseop Scinin
Bolts
Machi
Monda=800 79556
.7g load allow
ded fas
olt - Threahrough holeecured by tpposite the h
crew - Thrnserted thronto a threade
ne Scre
als N/m . Since
wable for the
steners
aded fastens in matingtightening head of the
readed fastough a holeed hole in a
ews
Des
e the total
e joint is 795
ner designeg members a nut frombolt.
tener desige in one mea mating me
sign o
l length of
55.6 N. The
ed to pass and to be
m the end
gned to be ember and ember.
of Join
f the weld
e joint is the
nt
d is 0.1 m
erefore safe.
Fig.
Fig.
Chaptem, the max
er 1 ximum
Page 25 of 263
S
S
T
ThT Tnu
S K Mo
Sheet M
Thread
he pitch linThread
hread Seriumber of th
ondal
Metal an
F
Profiles
e or diametSeriesies - groups
hreads per in
s
nd Lag S
Figure-Sheet
s
er is located
s of diametench applied
Desig
Screws
t metal scre
d at the h
er-pitch com to a specific
gn of
s
ews are often
height of the
mbinations dc diameter.
Joint
n self-tappi
e theoretical
distinguishe
C
ng.
l sharp v-th
ed from eac
Chapter
hread profile
ch other by
r 1
e.
the
Page 26 of 263
Design of Joint S K Mondals Chapter 1
M-Series Metric system of diameters, pitches, and tolerance/allowances.
Tensile Stress Area The average axial stress in a fastener is computed using a tensile stress area.
=avet
FA
+ = 2
4 2r p
t
D DA
F Axial Force Dr Root Diameter Dp Pitch Diameter At Tensile Stress Area ave Average axial stress
Length of Engagement (Equal Strength Materials) If the internal thread and external thread material have the same strength, then
Tensile Strength (External Thread)
maxt
t
FA
=
Shear Strength (Internal Thread)
max
,0.5 t
s i e
FA L
=
Where
max ,0.5t t t s i eF A A L = = =
,
2 te
s i
ALA
Bolt/Nut Design Philosophy ANSI standard bolts and nuts of equal grades are designed to have the bolt fail before the threads in the nut are stripped. The engineer designing a machine element is responsible for determining how something should fail taking into account the safety of the operators and public. Length of engagement is an important consideration in designing machine elements with machine screws.
Objective Questions (For GATE, IES & IAS)
Page 27 of 263
Design of Joint S K Mondals Chapter 1
Previous 20-Years GATE Questions Keys GATE-1. Square key of side "d/4" each and length l is used to transmit torque "T"
from the shaft of diameter "d" to the hub of a pulley. Assuming the length of the key to be equal to the thickness of the pulley, the average shear stress developed in the key is given by [GATE-2003]
2 2 34T 16T 8T 16T(a) (b) (c) (d)ld ld ld d
GATE-1. Ans. (c) If a square key of sides d/4 is used then. In that case, for shear failure we
have xd dl T4 2
=
x 28Torld
= [Where x is the yield stress in shear and l is the key length.] GATE-2. A key connecting a flange coupling to a shaft is likely to fail in[GATE-1995]
(a) Shear (b) tension (c) torsion (d) bending GATE-2. Ans. (a) Shear is the dominant stress on the key
Welded joints GATE-3. A 60 mm long and 6 mm thick fillet weld carries a steady load of 15 kN
along the weld. The shear strength of the weld material is equal to 200 MPa. The factor of safety is [GATE-2006] (a) 2.4 (b) 3.4 (c) 4.8 (d) 6.8
GATE-3. Ans. (b) Strength of materialFactorofsafety
Actual load or strength onmaterial=
3
6o
200(in MPa) 200(in MPa) 3.458.91(in MPa)15 10
660 10 (in MPa)cos45
= =
Threaded fasteners
Page 28 of 263
Design of Joint S K Mondals Chapter 1
GATE-4. A threaded nut of M16, ISO metric type, having 2 mm pitch with a pitch diameter of 14.701 mm is to be checked for its pitch diameter using two or three numbers of balls or rollers of the following sizes [GATE-2003] (a) Rollers of 2 mm (b) Rollers of 1.155 mm (c) Balls of 2 mm (d) Balls of 1.155 mm
GATE-4. Ans. (b)
Previous 20-Years IES Questions
Cotters IES-1. Assertion (A): A cotter joint is used to rigidly connect two coaxial rods carrying
tensile load. Reason (R): Taper in the cotter is provided to facilitate its removal when it fails due to shear. [IES-2008] (a) Both A and R are true and R is the correct explanation of A (b) Both A and R are true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true
IES-1. Ans. (b) A cotter is a flat wedge shaped piece of rectangular cross-section and its width is tapered (either on one side or both sides) from one end to another for an easy adjustment. The taper varies from 1 in 48 to 1 in 24 and it may be increased up to 1 in 8, if a locking device is provided. The locking device may be a taper pin or a set screw used on the lower end of the cotter. The cotter is usually made of mild steel or wrought iron. A cotter joint is a temporary fastening and is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces.
IES-2. Match List I with List II and select the correct answer using the code given
below the Lists: [IES 2007] List I List II
(Application) (Joint) A. Boiler shell 1. Cotter joint B. Marine shaft coupling 2. Knuckle joint C. Crosshead and piston road 3. Riveted joint D. Automobile gear box 4. Splines
(gears to shaft) 5. Bolted Joint Code: A B C D A B C D
(a) 1 4 2 5 (b) 3 5 1 4 (c) 1 5 2 4 (d) 3 4 1 5 IES-2. Ans. (b) IES-3. Match List-I (Parts to be joined) with List-II (Type of Joint) and select the
correct answer using the code given below: [IES-2006] List-I List -II
A. Two rods having relative axial motion 1. Pin Joint B. Strap end of the connecting rod 2. Knuckle Joint C. Piston rod and cross head 3. Gib and Cotter Joint D. Links of four-bar chain 4. Cotter Joint
A B C D A B C D (a) 1 3 4 2 (b) 2 4 3 1
Page 29 of 263
SIE IE
IE IE
IE
IE
IE IE
IE
S K Mo(c)
ES-3. Ans. (
ES-4. MaLiA. B.C.D.
Code(a)(c)
ES-4. Ans. (
ES-5. In(a)(c)
ES-5. Ans. (
ES-6. MacoLiA.
B.C D.
(a)(c)
ES-6. Ans. (
ES-7. Inthsh(a)
ES-7. Ans. (
ondal) 1 4 (d)
atch List Iist I (Types Riveted jo Welded jo Bolted joi. Knuckle js: A B ) 4 3 ) 2 4 (c)
n a gib and ) Single she) Single shea(d)
atch List Iorrect answist I Bolts in b
cylinder Cotters inRivets in l. Bolts hold
a flange cA B
) 4 1 ) 3 1 (a)
n a cotter hickness ishearing str) 120 N/mm(d) It i
Shear stre
s 3
I with List s of joints) oint oint int joint
C 2 3
cotter joinar only ar and crush
I (Items inwer using t
bolted joincover plat
n cotter joilap joints ding two flcoupling
C 3 4
joint, the s 12 mm. Tress develo
m2 is a case of d
ess Load2 Area
=
Desig
2 (d)
II and sele List 1. P 2. St 3. Lo 4. FD 1 (b) 1 (d)
nt, the gib hing
n joints) wthe codes g
nts of enginte int langes in
D 2 (b) 2 (d)
width of The load aoped in the(b) 100 N/mdouble shea
360 10a 2 50 12
=
gn of
2 3
ect the cort II (An elein trap ock washeillet
A B2 32 4
and cotter(b) doubl(d) doubl
with List IIgiven below
Lne 1
2 3 4
A B4 2 3 2
the cotteracting on te cotter? mm2 (car.
250N / mm2
=
Joint 4
rrect answement of th
er
B C 4 1
r are subjele shear onlle shear and
I (Type of w the Lists
List II .Doubletra
. Torsiona Single tra. Tension
B C 3 4
r at the cethe cotter c) 75 N/mm2
2
C1
er. he joint)
D 1 3
ected to ly d crushing
failure) ans:
ansverse sh
l shear ansverse sh
D 1 1
entre is 50r is 60 kN. 2 (d)
Chapter
[IES-199
[IES-200
nd select t [IES-20
hear
hears
0 mm and . What is t [IES-200) 50 N/mm2
r 1
94]
06]
the 04]
its the 04]
Page 30 of 263
Design of Joint S K Mondals Chapter 1
IES-8. The spigot of a cotter joint has a diameter D and carries a slot for cotter. The permissible crushing stress is x times the permissible tensile stress for the material of spigot where x > 1. The joint carries an axial load P. Which one of the following equations will give the diameter of the spigot?
[IES-2001]
(a) t
P x 1D 2x= (b) t
P x 1D 2x+= (c) t
2 P x 1Dx+= (d) t
2PD x 1= + IES-8. Ans. (b) IES-9. Match List-l (Machine element) with List-II (Cause of failure) and select
the correct answer using the codes given below the lists: [IES-1998] List-I List-II
A. Axle 1. Shear stress B. Cotter 2. Tensile/compressive stress C. Connecting rod 3. Wear D. Journal bearing 4. Bending stress Code: A B C D A B C D
(a) 1 4 2 3 (b) 4 1 2 3 (c) 4 1 3 2 (d) 1 4 3 2
IES-9. Ans. (b) In machinery, the general term shaft refers to a member, usually of circular
cross-section, which supports gears, sprockets, wheels, rotors, etc., and which is subjected to torsion and to transverse or axial loads acting singly or in combination.
An axle is a non-rotating member that supports wheels, pulleys, and carries no torque.
A spindle is a short shaft. Terms such as line-shaft, head-shaft, stub shaft, transmission shaft, countershaft, and flexible shaft are names associated with special usage.
IES-10. The piston rod and the crosshead in a steam engine are usually connected
by means of [IES-2003] (a) Cotter joint (b) Knuckle joint (c) Ball joint (d) Universal joint
IES-10. Ans. (a) IES-11. A cotter joint is used when no relative motion is permitted between the
rods joined by the cotter. It is capable of transmitting [IES-2002] (a) Twisting moment (b) an axial tensile as well as compressive load (c) The bending moment (d) only compressive axial load
IES-11. Ans. (b) IES-12. Match List I with List II and select the correct answer using the codes
given below the lists: [IES-1995] List I List II
(Different types of detachable joints) (Specific use of these detachable joints) A. Cotter joint 1. Tie rod of a wall crane B. Knuckle joint 2. Suspension bridges C. Suspension link joint 3. Diagonal stays in boiler D. Turn buckle (adjustable joint) 4. Cross-head of a steam engine Codes: A B C D A B C D
(a) 4 2 3 1 (b) 4 3 2 1 (c) 3 2 1 4 (d) 2 1 4 3
Page 31 of 263
SIE IE
IE
IE
IE
KIE
S K MoES-12. Ans.
ES-13. Magiv
A. B.C.D.
1. 2. 3. 4. 5. Co
ES-13. AnstwmaCoetc
ES-14. AsthupReloa(a)(b)(c)(d)
ES-14. Ans.
Keys ES-15. In
(a)
ondal. (a)
atch List ven below
List I (Ty Cotter joi Knuckle j Turn buck. Riveted jo
List II (M Connects Rigidly co Connects Permanen Connects odes: A
(a) 5 (c) 5
. (b) A cottwo rods whicay be subjeconnection ofc are examp
ssertion (Ae connectin
pon the direceason (R): ading and re) Both A and) Both A and) A is true b) A is false b. (b)
n the assem) pulley is m
s
I with Lis the lists:
ype of jointnt oint kle oint
Mode of jointwo rods o
onnects twtwo rods h
nt fluid-tigtwo shafts
B 1 3
er is a flat ch transmit cted to tensif piston rod ples of cotter
A): When thng rods eithction of rota A turn bucequiring subd R are indid R are indiut R is falsebut R is true
mbly of pulmade the we
Desig
st II and s t)
nting memor bars pero members
having threht joint be
s and transC D 3 2 2 4 wedge-shap motion in tile or compr to the crossr joint.
he coupler oher move clation of the ckle is usedbsequent adividually truividually true e
Fig. Tu
ley, key aneakest
gn of
select the
mbers) rmitting sms eaded end
etween twosmits torqu
A(b) 2 (d) 2
ped piece of the axial dirressive forces-head of a
of a turn buoser or mov coupler. d to connectdjustment foue and R is ue but R is n
urnbuckle
nd shaft (b) key is
Joint
correct an
mall amoun
s o flat pieceue
A B 1 3 steel. This
rection, withes along thesteam engin
uckle is turve away fro t two roundor tightenin the correct not the corr
s made the
C
nswer usin
nt of flexib
es
C D 3 4 1 4
is used to chout rotatioe axes of thene, valve ro
ned in one om each oth
d rods subjeng or looseni explanationrect explana
[IEweakest
Chapter
ng the cod [IES-19
bility
connect rigin. These joi
e rods. od and its st
direction bher depend [IES-199
ected to tening. n of A ation of A
S-1993; 199
r 1
des 93]
idly ints
tem
both ding 96] sile
98]
Page 32 of 263
S K M
IES-15. A
IES-16.
IES-16. A
IES-17.
IES-17. A IES-18.
IES-18. A IES-19.
IES-19. A
Monda(c) Key is m
Ans. (b) Keyfailure.
Match Licorrect anList-I A. WoodruB. KennedC. FeatheD. Flat keCode: A
(a) (c)
Ans. (b) A febe fastened
Match Ligiven beloList-I (KeyA. Gib heaB. WoodruC. ParalleD. SplinesCode: A
(a) (c)
Ans. (c)
A spur gerectangul(a) Shear s(c) Both sh
Ans. (c) Key
Assertioncapacity anReason (R(a) Both A (b) Both A (c) A is tru(d) A is fals
Ans. (d)
als made the str
y is made t
st-I (Typenswer usin uff key dy key r key
ey A B 2 3 2 3
eather key isd either to t
st-I with ow the listy/splines) ad key uff key el key s A B 1 2 2 1
ear transmlar sectionstress alone hear and beay develops bo
(A): The nd to increaR): Highly lo and R are i and R are ie but R is fase but R is t
Des
rongest
the weakest
of keys) ng the code
L 1 2 3 4C D1 4 4 1
s used whenhe hub or th
Fig.
List-II ands:
C D3 4 3 4
mitting pown. The type aring stresseoth shear an
effect of kese its torsioocalized strendividuallyndividuallyalse true
sign o
(d) astreng
t so that it
with Listes given be
List-II . Loose fitt. Heavy du. Self-align. Normal in
D (b) (d) n one compohe shaft and
feather key
d select th List-I1. Sel2. Fac3. Mo4. Ax
D (b) (d)
wer is con (s) of stres
(b) bees (d) shnd bearing s
eyways on onal rigidityesses occur
y true and Ry true but R
of Join ll the thregth is cheap an
t-II (Charaelow the Li
ting, light uty ning ndustrial u
A B 3 2 3 2
onent slidesd the keywa
y
he correct
II (Applicalf aligning cilitates re
ostly used ial movem
A B 1 2 2 1
nnected tosses develo
earing stresshearing, beastresses.
a shaft is y. at or near t
R is the corre is not the c
nt ee are des
nd easy to r
acteristic) ists:
duty
use C 1 4
s over anothay usually h
t answer
ation) emoval
ment possib C
4 4
o the shaftoped in thes alone ring and be
to reduce
the corners ect explanatcorrect expl
Chaptesigned for
replace in c
and selec [IES-
D 4 1
her. The keyhas a sliding
using the [IES-
ble D 3 3
t with a ke key is far [IES-
ending stres
its load ca [IES-of keyways.tion of A anation of A
er 1 equal
case of
ct the -1997]
y may g fit.
code -2008]
key of re. -1995] ses.
rrying -1994] .
A
Page 33 of 263
Design of Joint S K Mondals Chapter 1
IES-20. Which key is preferred for the condition where a large amount of impact torque is to be transmitted in both direction of rotation? [IES-1992] (a) Woodruff key (b) Feather key (c) Gib-head key (d) Tangent key
IES-20. Ans. (d) IES-21. What is sunk key made in the form of a segment of a circular disc of
uniform thickness, known as? [IES-2006] (a) Feather key (b) Kennedy key (c) Woodruff key (d) Saddle key
IES-21. Ans. (c) IES-22. What are the key functions of a master schedule? [IES-2005]
1. To generate material and capacity requirements 2. To maintain valid priorities 3. An effective capacity utilization 4. Planning the quantity and timing of output over the intermediate time horizons Select the correct answer using the code given below: (a) 1, 2 and 3 (b) 2, 3 and 4 (c) 1, 3 and 4 (d) 1, 2 and 4
IES-22. Ans. (b) IES-23. A square key of side d/4 is to be fitted on a shaft of diameter d and in the
hub of a pulley. If the material of the key and shaft is same and the two are to be equally strong in shear, what is the length of the key? [IES-2005]
(a) d2
(b) 2 d3 (c) 3 d
4 (d) 4 d
5
IES-23. Ans. (a) IES-24. Which one of the following statements is correct? [IES-2004]
While designing a parallel sunk key it is assumed that the distribution of force along the length of the key (a) Varies linearly (b) is uniform throughout (c) varies exponentially, being more at the torque input end (d) varies exponentially, being less at torque output end
IES-24. Ans. (c) Parallel sunk key. The parallel sunk keys may be of rectangular or square section uniform in width and thickness throughout. It may be noted that a parallel key is a taperless and is used where the pulley, gear or other mating piece is required to slide along the shaft. In designing a key, forces due to fit of the key are neglected and it is assumed that the distribution of forces along the length of key is uniform.
IES-25. Match List-I (Device) with List-II (Component/Accessory) and select the
correct answer using the codes given below the Lists: [IES-2003] List-I List-II (Device) (Component/Accessory)
A. Lifting machine 1. Idler of Jockey pulley B. Fibre rope drive 2. Sun wheel C. Differential gear 3. Sheave D. Belt drive 4. Power screw Codes: A B C D A B C D
(a) 4 3 1 2 (b) 3 4 1 2 (c) 4 3 2 1 (d) 3 4 2 1
IES-25. Ans. (c)
Page 34 of 263
S K M IES-26.
IES-26. A
IES-27.
IES-27. A
MondaA pulley means of key is takthe key isthe length
(a) 4
Ans. (c)
Shearing s
AssertionReason (Rof the mati(a) Both A (b) Both A (c) A is tru(d) A is fals
Ans. (b)
The main a1. It accom2. It is useftendency toThe main d1. The dept2. It can no
als is conneca rectangu
ken as d/4.s equal to th of the ke
(b)
trength of k
(A): A WooR): The Wooing piece. and R are i and R are ie but R is fase but R is t
advantages mmodates its
ful on tapero turn over dis-advantath of the keyot be used a
Des
cted to a ular sunk k. For full pthe torsiony to the di
2
3
dkey:F .4
Torque(T
Torsiona
or T d
For samed d. .l .4 2lord 2
=
=
=
odruff key isodruff key a ndividuallyndividuallyalse true
of a woodruself to any tring shaft en in its keywa
ages of a wooyway weake
as a feather.
sign o
power trakey of widpower trannal shearinameter of
(c) 2
3
3
.l
dT) =F. .2
l shearing,
16e strengthd d2 16
=
=
s an easily aaccommodat y true and Ry true but R
uff key are aaper in the nds. Its extray. odruff key aens the shaf
of Join
ansmissiondth wand lensmission, ng strengththe shaft (
4
d d.l .4 2T
dd232
=
adjustable ktes itself to
R is the corre is not the c
as follows: hub or bossra depth in t
are as followft.
nt
n shaft of ength l. T the shear
h of the sha(l/d) is
(d)
key. any taper i
ect explanatcorrect expl
s of the matthe shaft pr
ws:
Chapte
diameter The width oring strengaft. The ra [IES-
n the hub o [IES-tion of A anation of A
ing piece. revents any
er 1
d by of the gth of atio of -2003]
or boss -2003]
A
Page 35 of 263
Design of Joint S K Mondals Chapter 1
IES-28. The key shown in the above figure is a
(a) Barth key (b) Kennedy key (c) Lewis key (d) Woodruff key
[IES-2000]
IES-28. Ans. (a) IES-29. Match List I (Keys) with List II (Characteristics) and select the correct
answer using the codes given below the Lists: [IES-2000] List I List II
A. Saddle key 1. Strong in shear and crushing B. Woodruff key 2. Withstands tension in one direction C. Tangent key 3. Transmission of power through frictional
resistance D. Kennedy key 4. Semicircular in shape Code: A B C D A B C D
(a) 3 4 1 2 (b) 4 3 2 1 (c) 4 3 1 2 (d) 3 4 2 1
IES-29. Ans. (d) IES-30. Match List-I with List-II and select the correct answer using the code
given below the Lists: [IES-2009] List-I List-II
(Description) (shape) A. Spline 1. Involute B. Roll pin 2. Semicircular C. Gib-headed key 3. Tapered on on side D. Woodruff key 4. Circular Code: A B C D A B C D
(a) 1 3 4 2 (b) 2 3 4 1 (c) 1 4 3 2 (d) 2 4 3 1
IES-30. Ans. (c) IES-31. The shearing area of a key of length 'L', breadth 'b' and depth 'h' is equal to
(a) b x h (b) Lx h (c) Lx b (d) Lx (h/2) [IES-1998] IES-31. Ans. (c)
Splines IES-32. Consider the following statements: [IES-1998]
A splined shaft is used for 1. Transmitting power 2. Holding a flywheel rigidly in position 3. Moving axially the gear wheels mounted on it 4. Mounting V-belt pulleys on it. Of these statements (a) 2 and 3 are correct (b) 1 and 4 are correct
Page 36 of 263
Design of Joint S K Mondals Chapter 1
(c) 2 and 4 are correct (d) 1 and 3 are correct IES-32. Ans. (d)
Welded joints IES-33. In a fillet welded joint, the weakest area of the weld is [IES-2002]
(a) Toe (b) root (c) throat (d) face IES-33. Ans. (c) IES-34. A single parallel fillet weld of total length L and weld size h subjected to a
tensile load P, will have what design stress? [IES 2007] (a) Tensile and equal to P
0.707Lh (b) Tensile and equal to P
Lh
(c) Shear and equal to P0.707Lh
(d) Shear and equal to PLh
IES-34. Ans. (c)
Throat, t = h cos450 =
2
1 hv
= 0.707h
T = PLt
= P0.707Lh
IES-35. Two metal plates of thickness t and width 'w' are joined by a fillet weld of 45 as shown in given figure.
[IES-1998]
When subjected to a pulling force 'F', the stress induced in the weld will be
(a) oF
wt sin 45 (b) F
wt (c)
oFsin 45wt
(d) 2Fwt
IES-35. Ans. (a) IES-36. A butt welded joint, subjected to
tensile force P is shown in the given figure, l = length of the weld (in mm) h = throat of the butt weld (in mm) and H is the total height of weld including reinforcement. The average tensile stress t, in the weld is given by
[IES-1997]
( ) ( ) ( ) ( )t t t tP P P 2Pa b c d Hl hl 2hl Hl = = = = IES-36. Ans. (b)
Page 37 of 263
Design of Joint S K Mondals Chapter 1
IES-37. In the welded joint shown in the given figure, if the weld at B has thicker fillets than that at A, then the load carrying capacity P, of the joint will
(a) increase (b) decrease (c) remain unaffected (d) exactly get doubled
[IES-1997]
IES-37. Ans. (c) IES-38. A double fillet welded joint with parallel fillet weld of length L and leg B is
subjected to a tensile force P. Assuming uniform stress distribution, the shear stress in the weld is given by [IES-1996]
(a) 2P B.L
(b) P 2.B.L
(c) P2.B.L
(d) 2PB.L
IES-38. Ans. (c) IES-39. The following two figures show welded joints (x x x x x indicates welds),
for the same load and same dimensions of plate and weld. [IES-1994]
The joint shown in (a) fig. I is better because the weld is in shear and the principal stress in the weld is not in line with P (b) fig. I is better because the load transfer from the tie bar to the plate is not direct (c) fig. II is better because the weld is in tension and safe stress of weld in tension is greater than that in shear (d) fig. II is better because it has less stress concentration.
IES-39. Ans. (c) Figure II is better because the weld is in tension and safe stress of weld in tension is greater than shear.
IES-40. Assertion (A): In design of double fillet welding of unsymmetrical sections with
plates subjected to axial loads lengths of parallel welds are made unequal. Reason (R): The lengths of parallel welds in fillet welding of an unsymmetrical section with a plate are so proportioned that the sum of the resisting moments of welds about the centre of gravity axis is zero. [IES-2008] (a) Both A and R are true and R is the correct explanation of A (b) Both A and R are true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true
IES-40. Ans. (a) Axially loaded unsymmetrical welded joints
Page 38 of 263
Design of Joint S K Mondals Chapter 1
1
1
1 1
1 1
2 2
1 1 2 2
1 1 2 2
1 1 2 2
PA
P AP t IP t IP y P ytI y tI y
I y I y
== = =
= =
=
IES-41. Two plates are joined together by means of
single transverse and double parallel fillet welds as shown in figure given above. If the size of fillet is 5 mm and allowable shear load per mm is 300 N, what is the approximate length of each parallel fillet?
(a) 150 mm (b) 200 mm (c) 250 mm (d) 300 mm [IES-2005] IES-41. Ans. (b) ( )300 100 2l 15000 or l 200 + = = IES-42. A circular rod of diameter d is welded to a flat plate along its
circumference by fillet weld of thickness t. Assuming w as the allowable shear stress for the weld material, what is the value of the safe torque that can be transmitted? [IES-2004]
(a) 2 wd .t. (b) 2
wd .t.2
(c) 2
wd .t.
2 2 (d)
2
wd .t.2
IES-42. Ans. (b)
( )
W
W2
W W
Shear stressShear fore dt
d dTorque T dt .t2 2
= =
= =
IES-43. A circular solid rod of diameter d welded to a rigid flat plate by a circular
fillet weld of throat thickness t is subjected to a twisting moment T. The maximum shear stress induced in the weld is [IES-2003] (a) 2
Ttd (b) 2
2Ttd (c) 2
4Ttd (d) 3
2Ttd
IES-43. Ans. (b) 3 2
dT.T.r 2T2J td td
4
= = =
Page 39 of 263
Design of Joint S K Mondals Chapter 1
IES-44. The permissible stress in a filled weld is 100 N/mm2. The fillet weld has equal leg lengths of 15 mm each. The allowable shearing load on weldment per cm length of the weld is [IES-1995] (a) 22.5 kN (b) 15.0 kN (c) 10.6 kN (d) 7.5 kN.
IES-44. Ans. (c) Load allowed = 100 x 0.707 x 10 x15 = 10.6 kN
Threaded fasteners IES-45. A force F is to be transmitted through a square-threaded power screw
into a nut. If t is the height of the nut and d is the minor diameter, then which one of the following is the average shear stress over the screw thread? [IES 2007]
(a) 2fdt (b)
Fdt (c)
F2 dt (d)
4Fdt
IES-45. Ans. (b) IES-46. Consider the case of a square-
threaded screw loaded by a nut as shown in the given figure. The value of the average shearing stress of the screw is given by (symbols have the usual meaning)
( )
r r
2F F(a) (b)d h d h
2F F(c) ddh dh
[IES-1997] IES-46. Ans. (b) IES-47. Assertion (A): Uniform-strength bolts are used for resisting impact loads.
Reason (R): The area of cross-section of the threaded and unthreaded parts is made equal. [IES-1994] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true
IES-47. Ans. (c) A is true and R is false. IES-48. How can shock absorbing capacity of a bolt be increased? [IES 2007]
(a) By tightening it property (b) By increasing the shank diameter (c) By grinding the shank (d) By making the shank diameter equal to the core diameter of thread
IES-48. Ans. (d)
IES-49. The number of slots is a 25 mm castle nut is [IES-1992] (a) 2 (b) 4 (c) 6 (d) 8
IES-49. Ans. (c)
Page 40 of 263
Design of Joint S K Mondals Chapter 1
Answers with Explanation (Objective)
Page 41 of 263
Design of Friction Drives S K Mondals Chapter 2
2. Design of Friction Drives
Theory at a glance (GATE, IES, IAS & PSU)
Couplings
Introduction Couplings are used to connect two shafts for torque transmission in varied applications. It may be to connect two units such as a motor and a generator or it may be to form a long line shaft by connecting shafts of standard lengths say 6-8m by couplings. Coupling may be rigid or they may provide flexibility and compensate for misalignment. They may also reduce shock loading and vibration. A wide variety of commercial shaft couplings are available ranging from a simple keyed coupling to one which requires a complex design procedure using gears or fluid drives etc. However there are two main types of couplings: Rigid couplings. Flexible couplings.
Rigid couplings are used for shafts having no misalignment while the flexible couplings can absorb some amount of misalignment in the shafts to be connected. In the next section we shall discuss different types of couplings and their uses under these two broad headings.
Types and uses of shaft couplings
Rigid couplings Since these couplings cannot absorb any misalignment the shafts to be connected by a rigid coupling must have good lateral and angular alignment. The types of misalignments are shown schematically in figure below.
Page 42 of 263
Design of Friction Drives S K Mondals Chapter 2
Figure- Types of misalignments in shafts
Sleeve coupling One of the simple types of rigid coupling is a sleeve coupling which consists of a cylindrical sleeve keyed to the shafts to be connected. A typical sleeve coupling is shown in figure below
0d
L
id
Figure- A typical sleeve coupling Normally sunk keys are used and in order to transmit the torque safely it is important to design the sleeve and the key properly. The key design is usually based on shear and bearing stresses. If the torque transmitted is T, the shaft radius is r and a rectangular sunk key of dimension b and length L is used then the induced shear stress (figure below) in the key is given by
2
TLb r
=
And for safety ( )2 / yT bLr <
Page 43 of 263
Design of Friction Drives S K Mondals Chapter 2
Where y is the yield stress in shear of the key material. A suitable factor of safety must be used. The induced crushing stress in the key is given as
2 2br
Tb L r
=
And for a safe design 4T /(bLr) < c Where c is the crushing strength of the key material.
Figure- Shear and crushing planes in the key.
The sleeve transmits the torque from one shaft to the other. Therefore if di is the inside diameter of the sleeve which is also close to the shaft diameter d (say) and d0 is outside diameter of the sleeve, the shear stress developed in the sleeve is
( ) = 04 4016
sleevei
Tdd d
and the shear stress in the shaft is given by
= 316
shafti
Td
. Substituting yield shear stresses of the sleeve and shaft materials for
sleeve and shaft both di and d0 may be evaluated. However from the empirical proportions we have: d0 = 2di + 12.5 mm and L=3.5d. These may be used as checks. Sleeve coupling with taper pins Torque transmission from one shaft to another may also be done using pins as shown in figure below.
Page 44 of 263
Design of Friction Drives S K Mondals Chapter 2
Figure- A representative sleeve coupling with taper pins
The usual proportions in terms of shaft diameter d for these couplings are: d0 = 1.5d, L = 3d and a = 0.75d. The mean pin diameter dmean = 0.2 to 0.25 d. For small couplings dmean is taken as 0.25d and for large couplings dmean is taken as 0.2d. Once the dimensions are fixed we may check the pin for shear failure using the relation
= 22
4 2meandd T .
Here T is the torque and the shear stress must not exceed the shear yield stress of the pin material. A suitable factor of safety may be used for the shear yield stress.
Clamp coupling A typical clamp coupling is shown in figure below. It essentially consists of two half cylinders which are placed over the ends of the shafts to be coupled and are held together by through bolt.
Figure- A representative clamp coupling
The length of these couplings L usually vary between 3.5 to 5 times the and the outside diameter d0 of the coupling sleeve between 2 to 4 times the shaft diameter d. It is assumed that even with a key the torque is transmitted due to the friction grip. If now the number of bolt on each half is n, its core diameter is dc and the coefficient of friction between the shaft and sleeve material is we may find the torque transmitted T as follows. The clamping pressure between the shaft and the sleeve is given by
Page 45 of 263
Design of Friction Drives S K Mondals Chapter 2
( )2 / 22 4 c tnp d dL = Where n is the total number of bolts, the number of effective bolts for each shaft is n/2 and t is the allowable tensile stress in the bolt. The tangential force per unit area in the shaft periphery is F = p. The torque transmitted can therefore be given by
= 2 2dL dT p
Ring compression type couplings The coupling (figure below) consists of two cones which are placed on the shafts to be coupled and a sleeve that fits over the cones. Three bolts are used to draw the cones towards each other and thus wedge them firmly between the shafts and the outer sleeve. The usual proportions for these couplings in terms of shaft diameter d are approximately as follows: d1 = 2d + 15.24 mm L1 = 3d d2 = 2.45d + 27.94 mm L2 = 3.5d + 12.7 mm d3 = 0.23d + 3.17 mm L3 = 1.5d And the taper of the cone is approximately 1 in 4 on diameters.
Figure- A representative ring compression type coupling.
.
Oldham coupling These couplings can accommodate both lateral and angular misalignment to some extent. An Oldham coupling consists of two flanges with slots on the faces and the flanges are keyed or screwed to the shafts. A cylindrical piece, called the disc, has a narrow rectangular raised portion running across each face but at right angle to each other. The disc is placed between the flanges such that the raised portions fit into the slots in the flanges. The disc may be made of flexible materials and this absorbs some misalignment. A schematic representation is shown in figure below.
Page 46 of 263
S K M
UniverThese joinwidely usejoint is scommerciacenter piethe two foroften knowparallel of
Designcoupli Flange It is a verbolted. Th
Monda
rsal joints are capaed in agricushown in fally but theyce through rk ends sucwn as, Hooffset.
n proceings
couplinry widely u
his is illustra
Desials
Figure- A s
nts (or able of hanultural macfigure beloy essentiallwhich passh that a larokes coup
Figure- -Uedures
ng used rigid cated in figur
gn of
schematic di
Hookedling relatichinery, maow. There ly consist of s two pins wrge angular pling has n
Universal jofor rig
coupling andre below.
Frict
iagram of an
s or) cively large achine toolsare many
f two forks kwith mutual misalignmeno torsional
oints (or Hoogid and
d consists o
ion Dr
n Oldham c
coupling angular ms and autom forms of keyed or scrlly perpendient can be al rigidity n
okes or) cou flexibl
of two flang
rives
coupling
g misalignmemobiles. A
these courewed to theicular axes accommodatnor can it a
upling le rubb
ges keyed t
Chapte
ent and thetypical uniplings, ava
e shaft. Theand they co
ted. The couaccommodat
ber-bus
to the shaft
er 2
ey are iversal ailable re is a onnect upling, te any
hed
ts and
Page 47 of 263
S
T(a(b(c
RA flaboprboon Thtocopr (1
W (2
S K Mo
he main fea) Design of b) Design of ) Overall de
Rigid Fl typical rigianges whicholted in the rovided to golt circle diane flange an
he design porque transoupling are rocedure is
1) Shaft diam
Where T is th
2) Hub diam
Dondal
eatures of t bolts. hub. esign and di
ange Cid flange couh are keyed annular spguard the pameter and
nd a recess o
procedure ismission an obtained. given in the
meterd bas
he torque an
meter, d1 =
Desigs
Figu
the design
imensions.
Couplinupling is shd to the shaace between
projecting bd the numbeon the oppos
is generallynd then foCheck for
e following s
sed on torqu
nd y is the y
=1.75d + 6.5
n of F
ure- A typica
n are essen
g hown in Figuafts to be jon the hub anolt heads aer of bolt dsing face is
y based on ollowing em
different fasteps:
ue transmis
1d =
yield stress
5 mm
Frictio
al flange cou
tially
ure above. Ioined. The fnd the prote
and nuts. Thepends on t provided fo
determininmpirical relailure mode
ssion is give
1/16
s
T
in shear.
on Driv
upling
If essentiallflanges are ecting flanghe bolts arethe shaft dir ease of as
ng the shaftlations diffees can then
en by
3
ves C
ly consists obrought tog
ge. The protee placed equiameter d. Asembly.
ft diameter erent dimen be carrie
Chapter
of two cast igether and ective flangui-spaced oA spigot A
d for a givensions of ed out. Des
r 2
ron are
ge is n a on
ven the
sign
Page 48 of 263
Design of Friction Drives S K Mondals Chapter 2
(3) Hub length, L = 1.5d But the hub length also depends on the length of the key. Therefore this length L must be checked while finding the key dimension based on shear and crushing failure modes. (4) Key dimensions: If a square key of sides b is used then b is commonly taken as
4d . In that case, for shear failure
we have
= k4 2yd dL T
Where y is the yield stress in shear and Lk is the key length.
This gives =k 28
y
TLd
If Lk determined here is less than hub length L we may assume the key length to be the same as hub length. For crushing failure we have
= k8 2cd dL T Where c is crushing stress induced in the key. This gives
= 2k
16c
TL d
And if c < cy , the bearing strength of the key material ,the key dimensions chosen are in order. (5) Bolt dimensions: The bolts are subjected to shear and bearing stresses while transmitting torque. Considering the shear failure mode we have
cb yb
dn d24 2
= Where n is the number of bolts, db nominal bolt diameter, T is the torque transmitted, yb is the shear yield strength of the bolt material and dc is the bolt circle diameter. The bolt
Page 49 of 263
Design of Friction Drives S K Mondals Chapter 2
diameter may now be obtained if n is known. The number of bolts n is often given by the following empirical relation:
4 3150
n d= + Where d is the shaft diameter in mm. The bolt circle diameter must be such that it should provide clearance for socket wrench to be used for the bolts. The empirical relation takes care of this. Considering crushing failure we have
= cb cyb dn d t2. 2 Where 2t is the flange width over which the bolts make contact and cyb is the yield crushing strength of the bolt material. This gives t2. Clearly the bolt length must be more than 2 2t and a suitable standard length for the bolt diameter may be chosen from hand book. (6) A protecting flange is provided as a guard for bolt heads and nuts. The thickness t3 is less than 2 2
t the corners of the flanges should be rounded. (7) The spigot depth is usually taken between 2-3mm. (8) Another check for the shear failure of the hub is to be carried out. For this failure mode we may write
11 2 2yf
dd t = Where d1 is the hub diameter and yf is the shear yield strength of the flange material. Knowing yf we may check if the chosen value of t2 is satisfactory or not. Finally, knowing hub diameter d1, bolt diameter and protective thickness t2 We may decide the overall diameter d3. Flexible rubber bushed couplings Flexible coupling
Page 50 of 263
S K MAs discussvariety of will be dis This is simbelow.
In a rigid the bolts a However iabove) pro Because of
(1) Bea Rubber bubushes aremm thicknbrass sleev Thickness
Where db ithickness
Mondased earlier t flexible coucussed here
mplest type
Fi
coupling thand in this a
in the busheovide flexibi
f the rubber
aring sushings aree mostly avaness for larve
may be tak
is the diamof rubber bu
Desials these coupliuplings aree.
of flexible c
igure- A typ
e torque is arrangemen
ed coupling lity and the
r bushing th
tress e available ailable in thrger bores.
ken to be 1.5
eter of the bushing. We
gn of
ings can acc available c
coupling an
ical flexible
transmittednt shafts nee
the rubberese coupling
he design fo
for differenhickness betBrass sleev
5mm. The o
dr = d
bolt or pin, may now w
Frict commodate commercial
d a typical
e coupling w
d from one hed be aligne
r bushings og can accomm
r pins shoul
nt inside antween 6 mmves are ma
utside diam
db +2 tbr +2
tbr is the thwrite
ion Dr some misally and prin
coupling of
with rubber b
half of the ced very well
over the pinmodate som
ld be consid
nd out side m to 7.5 mmade to suit
meter of rubb
tr
hickness of t
rives ignment an
ncipal featu
this type is
bushings.
coupling to t.
ns (bolts) (asme misalignm
dered carefu
diameters. m for bores u
the require
ber bushing
the brass sl
Chaptend impact. Ares of only
s shown in F
the other th
s shown in Fment.
ully.
However rupto 25 mm ements. How
g dr is given
leeve and tr
er 2 A large a few
Figure
hrough
Figure
rubber and 9 wever,
by
is the
Page 51 of 263
Design of Friction Drives S K Mondals Chapter 2
2. 2c
r bdn d t p T=
Where dc is the bolt circle diameter and t2 the flange thickness over the bush contact area. A suitable bearing pressure for rubber is 0.035 N/mm2 and the number of pin is given by
325dn = + where d is in mm.
The dc here is different from what we had for rigid flange bearings. This must be judged considering the hub diameters, out side diameter of the bush and a suitable clearance. A rough drawing is often useful in this regard. From the above torque equation we may obtain bearing pressure developed and compare this with the bearing pressure of rubber for safely.
(2) Shear stress The pins in the coupling are subjected to shear and it is a good practice to ensure that the shear plane avoids the threaded portion of the bolt. Unlike the rigid coupling the shear stress due to torque transmission is given in terms of the tangential force F at the outside diameter of the rubber bush. Shear stress at the neck area is given by
2
2
4
b rb
neck
p t d
d =
Where dneck is bolt diameter at the neck i.e. at the shear plane.
Bending Stress The pin loading is shown in Figure below.
Page 52 of 263
S K M
Clearly thbending of
Knowing tusing appr We may al Hub diam Hub lengt
Pin diame
Monda
he bearing f the pin. Co
the shear anropriate the
lso assume
meter = 2d
th = 1.5d
eter at the n
Desials
Figure- Lo
pressure thonsidering a
nd bending eories of fail
the followin
neck = 0.5n
gn of
oading on a
hat acts asan equivalen
3b =
stresses welure.
ng empirical
5dn
Frict
pin support
s distributent concentra
( 23
32br
F td
e may check
l relations:
ion Dr
ting the bus
d load on rated load F=
)/ 2r
k the pin dia
rives
shings.
rubber bus= pt2d the b
ameter for p
Chapte
h would prbending stre
principal st
er 2
roduce ess is
tresses
Page 53 of 263
Design of Friction Drives S K Mondals Chapter 2
Problems with Solution Q. Design a typical rigid flange coupling for connecting a motor and a centrifugal
pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter.
Solution: The shaft diameter based on strength may be given by
= 316
y
Td Where T is the torque transmitted and y is the allowable yield
stress in shear.
Here T32 15 10Power / 143Nm2 100060
60
N
= = =
And substituting y = 60 x 106 Pa we have. Let us consider a shaft of 25 mm which is a standard size. From the rigidity point of view
T GJ L
=
Substituting T = 143Nm, ( )4 9 4 90.025 38.3 10 , 84 1032J m G Pa = = =
9 9143
38.3 10 84 10L
= = 0.044 radian per meter The limiting twist is 1 degree in 20 times the shaft diameter
Which is 180 0.03520 0.025
= radian per meter
Therefore, the shaft diameter of 25mm is safe. We now consider a typical rigid flange coupling as shown in Figure above Hub
Page 54 of 263
Design of Friction Drives S K Mondals Chapter 2
Using empirical relations Hub diameter d1 = 1.75d + 6.5 mm. This gives d1 = 1.75 x 25 + 6.5 = 50.25mm say d1 = 51 mm Hub length L=1.5d. This gives L = 1.5 x 25 = 37.5mm, say L= 38mm. Hub thickness, 11
51 25 132 2
d dt mm = = =
Key Now to avoid the shear failure of the key (refer to Figure above)
4 2k yd dL T = , Where the key width 4
dw = and the key length is Lk
This gives ( ) ( )268 143. . 0.0366 36.6
50 10 0.025i e m mm = = k 2y
8TL = d
The hub length is 37.5 mm. Therefore we take Lk = 37.5mm. To avoid crushing failure of the key (Refer to Figure below)
8 2kd dL = , Where is the crushing stress developed in the key.
This gives 216
k
TL d
= Substituting T = 143Nm, Lk = 37.5 x 10-3 m and d = 0.025 m
( )6
23
16 143 10 97.62MPa37.5 10 0.025
= =
Assuming an allowable crushing stress for the key material to be 100MPa, the key design is safe. Therefore the key size may be taken as: a square key of 6.25 mm size and 37.5 mm long. However keeping in mind that for a shaft of diameter between 22mm and 30 mm a rectangular key of 8mm width, 7mm depth and length between 18mm and 90mm is
Page 55 of 263
Design of Friction Drives S K Mondals Chapter 2
recommended. We choose a standard key of 8mm width, 7mm depth and 38mm length which is safe for the present purpose.
Bolts To avoid shear failure of bolts