INSTALLATION GUIDE FOR MOUNT KIT (BOCN0103)
SUITS: Nissan NP300
(Refer to website for suitable model years and variants)
BOCAR NUDGE BAR
https://bocar.com.au/nudge-bars/BOCN0103
BOCAR NUDGE BAR 21-Jan-21 Page 2 of 9
Important Notes:
• Nudge bar suits for non-parking sensor variants only
• Read instructions completely before commencing fitment.
• Towing point is removed for this product fitting.
• Additional fitting kits may be required for vehicles fitted with parking sensors, radar, winch etc.
consult website or retailer.
• Bocar and its affiliated companies are not responsible for any damage that may occur to you or
your vehicle during the installation of these products.
Electrical system damage may be possible due to incorrect wiring or method and is the
responsibility of the person fitting.
Note: Incandescent test lamps are not recommended as damage to vehicle electronics is
possible.
Please consult an auto electrician if you are not comfortable with modifying the vehicles
electrical system.
• Do not attach VFPS to the vehicle using anchorages not intended for this purpose (e.g. engine
mountings bolts).
• Do not use this product for any vehicle make or model, other than those specified by the VFPS
manufacturer.
• Do not remove the plaque or label from the VFPS.
• Do not modify the structure of the VFPS in any way.
Bolt tensions Dia. (mm) Nm
All bolt tensions are as follows unless otherwise specified.
5 5
6 9
8 22
10 44
12 77
BOCAR NUDGE BAR 21-Jan-21 Page 3 of 9
Required kits – Nudge Kit – BOCN0100 or BOCN0200
Item
No. Description Qty Part No.
BOLT KIT
5 M12 x 1.25 x 50 Hex Bolt - ZP DIN – CL 8.8 4 K0572
6 1/2 x 1-1/4 x 2.5mm ZP - Washer Flat 10 K0623
7 M12 x 1.25 ZP Nut Hex Nyloc 6 K1200
4 M12X1.25X30 Hex Bolt on Wire 2 BOCON0047
Item No. Description Qty Part No.
PARTS LIST
N/A Bocar Nudge Bar
(Purchased separately) 1
BOCN0200
or
BOCN0100
Mount Kit
2 Mount LH 1 BOCN0028L
3 Mount RH 1 BOCN0028R
1 Mount Spacer 2 BOCN0012
N/A Compliance Label – Nissan NP300 1 -
BOCAR NUDGE BAR 21-Jan-21 Page 4 of 9
Assembly Images:
BOCAR NUDGE BAR 21-Jan-21 Page 5 of 9
1. Before fitting, please check factory
bumper and grille are compatible with
your nudge bar.
2. Remove the number plate from the
bumper and retain.
3. Remove and retain middle bumper skirt
to gain access to the underside of the
front chassis. Retain fasteners.
4. Ensure Compliance Label is fixed to the
rear side of the tube as shown. Surface
must be clean before sticker applied.
5. Fit the RH Mount (BOCN0028R) to the
Right-Hand chassis using M10x1.25x30
• Hex Bolt on Wire (2)
• 1/2 x Ø1-1/4 Flat Washer (2)
• M12 x 1.25 Nyloc Nut (2)
(Feed in through slots in outer chassis
face near wheel arch.)
Align straight with chassis and tighten in
place.
LHS SHOWN
Front
BOCAR NUDGE BAR 21-Jan-21 Page 6 of 9
6. Remove the OE tow point and discard,
retain fasteners.
7. Using the fasteners from previous step
fasten the LH mount to the left front
chassis. (Original Bolts into tow point
location). Align with chassis and tighten
in place.
8. Neatly trim middle bumper skirt as
shown. Remove shaded areas.
9. Refit trimmed middle skirt.
10. Lift nudge bar to mounts and check skirt
trimming. Adjust on vehicle if necessary.
Nudge bar fits to inside of chassis
mounts.
Front
BOCAR NUDGE BAR 21-Jan-21 Page 7 of 9
11. If required use Mount Spacers between
the nudge bar and the mount. Then fit
the nudge bar using:
• M12 x 1.25 x 50mm Hex Bolt (2)
• 1/2 x Ø1-1/4 mm Flat Washer (4)
• M12 x 1.25 Nyloc Nut (2)
Repeat for opposite side.
Mounts have a small amount of adjustment to the
chassis left and right. Reposition if required.
12. Ensure there is adequate clearance
between the nudge bar and the front of
the bumper.
13. Tighten all the previously installed
fasteners to the relevant torque settings
listed on Page 2.
SPACER
LHS SHOWN
BOCAR NUDGE BAR 21-Jan-21 Page 8 of 9
14. Refit the number plate to the nudge bar
using:
• M6 x 1.0 x 20mm Hex Bolt (2)
• M6 x 1.0 Flange Nut (2)
from Nudge bar kit (BOCN100 or BOCN200)
BOCAR NUDGE BAR 21-Jan-21 Page 9 of 9
PRODUCT CARE & INFORMATION Customer Copy
Corrosion Protection Tips
• Going on an adventure! Be sure to rinse all areas and remove any sand, mud, or debris in
and around any areas that can catch this type of matter.
• Going to the beach! Make sure to rinse all salt water and sand off. To improve the
longevity and life of this product, be very thorough with fresh water and a sponge.
Nuts and Bolts
• At Bocar we do not get to experience your adventures or service your vehicle, so be sure
to regularly check all nuts and bolts, especially after a large Off-Road trip or regular use
on Civil, Mining and construction sites.
Love Care and Attention
• Planning to drive in a salty environment! If so, spray all fasteners with a Lanolin or WD40
protectant for longevity.
• If you spot a deep scratch touch up with paint to help prevent rust and inhibit corrosion.
• Regularly Wash & Dry the product the same as your vehicle using normal car wash to
maintain appearance.
Modifying Your Vehicle
• Modifications to your vehicle involves some risk, all care has been taken to test driver
aids, so they work as the vehicle manufacturer intended. There may be the need to re-
calibrate after fitment by the vehicle manufacturer. As the owner of your vehicle the
driver remains, responsible for the vehicle at all times when driving.
• Check and re-tighten any components after your first adventure. Regular upkeep will
help you get the most out of your Genuine Bocar Product and your pride and joy.
Warranty
• 2yr/40,000km. Warranty conditions apply. Our goods come with consumer guarantees
that cannot be excluded under the Australian Consumer Law. Our warranty does not
limit and may not exceed your rights under those guarantees. For full details on our
warranty please refer to www.bocar.com.au/warranty