B T L INSTITUTE OF TECHNOLOGY & MANAGEMENT
No.259/B, Hosur Road, Boomasandhra, Bangalore- 560 099
A LAB MANUAL ON
LOGIC DESIGN
Subject Code: 10ESL38
(As per VTU Syllabus)
PREPARED BY
Staff Members - Dept. of ECE
Logic Design Lab
10ESL38
Dept. of ECE 1 BTL Institute of Technology & Management
TABLE OF C O NTEN T S
Experi m ents
IC Pin Configurations
Page N o.
2
1. Boolean Expression realization using Logic gates 4
2. Half/Full Adder and Subtractor 7
3. a. Parallel Adder/ Subtractor 10
b. BCD to Excess-3 and Vice-versa 14
4. Binary to Gray Conversion and vice versa 16
5. MUX/DEMUX for arithmetic circuits 21
6. Comparators 27
7. Decoder Chip for LED Display 31
8. Priority Encoder 33
9. Flip-Flop verification 35
10. Counters 38
11. Shift Registers 50
12. Ring Counter/ Johnson Counter 55
13. Sequence Generator 57
Logic Design Lab Syllabus – 10ESL38 59
Possible Viva Questions 60
Dept. of ECE 2 BTL Institute of Technology & Management
Logic Design Lab
10ESL38
IC Pin c o n f i g urations Inverter (NOT Gate) - 7404LS 2-Input AND Gate - 7408LS
2-Input OR Gate - 7432LS 2-Input NAND Gate - 7400LS
2-Input NOR Gate - 7402LS 2-Input EX-OR Gate - 7486LS
3-Input NAND Gate - 7410LS 4-bit Binary Full Adder74LS83
Dept of ECE 3 BTL Institute of Technology & Management
Logic Design Lab
10ESL38
Dual 4-Input NAND Gate - 7420LS Dual 4-input Multiplexer74153
4-Bit Magnitude Comparator - 7485 Decoders/Demultiplexer 74139
Shift Register - 7495 Synchronous Up/Down Counter– 74192
Deci m al sc a l ar - 7490 D u alJK Fli p -f l op– 7476
Dept of ECE 4 BTL Institute of Technology & Management
Logic Design Lab
10ESL38
Experiment No. 1
BO O LE A N EXPRE S SI O N REAL I Z A TION U S I NG L O G I C GATES
Aim: – To Simplify and Realize Boolean expressions using logic gates/Universal gates.
Components Required: - IC 7408 (AND), IC 7404 (NOT), IC 7432 (OR),IC 7400 (NAND), IC 7402 (NOR),IC 7486 (EX-OR)
Procedure –
1. Verify that the gates are working.
2. Construct a truth table for the given problem.
3. Draw a Karnaugh Map corresponding to the given truth table.
4. Simplify the given Boolean expression manually using the Karnaugh Map.
A: Implementation Using Logic Gates
5. Realize the simplified expression using logic gates.
6. Connect VCC and ground as shown in the pin diagram.
7. Make connections as per the logic gate diagram.
8. Apply the different combinations of input according to the truth tables.
9. Check the output readings for the given circuits; check them against the truth tables.
10. Verify that the results are correct.
B. Implementation Using Universal Gates
11. Convert the AND-OR logic into NAND-NAND and NOR-NOR logic.
12. Implement the simplified Boolean expressions using only NAND gates, and then
using only NOR gates.
13. Connect the circuits according to the circuit diagrams, apply inputs according to
the truth table and verify the results.
11
0 0 0 0
0 0 0 0
1 11 1
Dept of ECE 5 BTL Institute of Technology & Management
Logic Design Lab
10ESL38
Given Problem:
Truth Table:
A B C D Y0 0 0 0 00 0 0 1 00 0 1 0 00 0 1 1 00 1 0 0 00 1 0 1 10 1 1 0 10 1 1 1 11 0 0 0 01 0 0 1 01 0 1 0 01 0 1 1 01 1 0 0 01 1 0 1 11 1 1 0 11 1 1 1 1
Switching Expression:
∑
πKarnaugh Map Simplification:
K-Map for SOP CD
K-Map for
POS CD
AB 00 01 11 10
00011110 BC
BD
AB 00 01 11 10
00
01 0 B
11 0
10
C+D
Simplified Boolean Expression:
SOP form Y=f(A,B,C,D)=BC+BD
POS form Y=f(A,B,C,D)=B(C+D)
D
D
Expression Realization using Basic Gates:
C 17408 3
2
B4
7408 6
5
17432
2
3 Y=BC+BD
BC 1
37432D 2
17408 3
2
Y=B(C+D)
Realization using only NAND gates: Realization using only NOR gates:
C 17400 3
2
B4
97400
10
8Y=BC+BD
2
B 74023
C 8
1 57402
6
4 Y=B(C+D)
7400 6
57402 10
D 9
Realization using only NOR gates:
2C 7402
3
5B 7402
6
8
D 74029
1 11
12
4
2
310
7402 13
7402' 1
57402'
6
84 7402'
9
10 Y=BC+BD
Realization using only NAND gates:
B1
C 7400 3
2
4
D 7400 6
5
9 8
7400
10
117400
12
13 17400'
2
3 Y=B(C+D)
Experiment No. 2
HALF/FU L L ADDER AND HALF/FULL S U B TR A C T OR
Aim: – To realize half/full adder and half/full subtractor using Logic gates
Components Required: - IC 7408, IC 7432, IC 7486, IC 7404, etc.
Procedure: -
1. Verify that the gates are working.
2. Make the connections as per the circuit diagram for the half adder circuit, on the trainer
kit.
3. Switch on the VCC power supply and apply the various combinations of the inputs
according to the respective truth tables.
4. Note down the output readings for the half adder circuit for the corresponding
combination of inputs.
5. Verify that the outputs are according to the expected results.
6. Repeat the procedure for the full adder circuit, the half subtractor and full subtractor
circuits.
7. Verify that the sum/difference and carry/borrow bits are according to the expected
values.
3
Half Adder Using Basic Gates
A B S C
0 0 0 0
0 1 1 0
1 0 1 0
1 1 0 1
A. Half Adder using Logic Gates:
A 1
7486B 2
17408 3
2
B. Full Adder Using Logic Gates
Full Adder Using Basic Gates
A B Cn-1 S C
0 0 0 0 0
0 0 1 1 0
0 1 0 1 0
0 1 1 0 1
1 0 0 1 0
1 0 1 0 1
1 1 0 0 1
1 1 1 1 1
Half Subtractor Using Basic Gates
A B D B
0 0 0 0
0 1 1 1
1 0 1 0
1 1 0 0
C. Half Subtractor Using Logic Gates
C
D. Full Subtractor Using Logic Gates
Full Subtractor Using Basic Gates
A B Cn-1 D B
0 0 0 0 0
0 0 1 1 1
0 1 0 1 1
0 1 1 0 1
1 0 0 1 0
1 0 1 0 0
1 1 0 0 0
1 1 1 1 1
Dept of ECE. 1010
BTL Institute of Technology & Management
Experiment No. 3
P A RA L LEL ADDER A N D SUB T R A CTOR U S I NG 7483
Aim: –i. To realize Parallel Adder and Subtractor Circuits using IC 7483ii. BCD to Excess-3 Code conversion and Vice Versa using IC7483
Components Required: - IC 7483, IC 7486, etc.
Procedure: -
1. Connect one set of inputs from A1 to A4 pins and the other set from B1 to B4, on
the IC 7483.
2.Connect the pins from S1 to S4 to output terminals.
3. Short S,C0 to XOR gate 1 input and other input take from C4 and obtain the
Output Carry Cout (Output Borrow Bout).
4. In order to Perform Addition take S=0.
5. In order to implement the IC 7483 as a subtractor, Take S=1, Apply the B input
through XOR gates (essentially taking complement of B).
6. Apply the inputs to the adder/ subtractor circuits as shown in the truth tables.
7. Check the outputs and note them down in the table for the corresponding inputs.
8. Verify that the outputs match with the expected results.
IC 7483 Pin Diagram
7483
1
74862
4
5
9
10
74868
7
12
748611
1113
13
Dept of ECE. 1111
BTL Institute of Technology & Management
A. IC 7483 as a Parallel Adder
Circuit Diagram:
VCC
A4 5
OutputCarry
1
Input Data A
B4
1A3
3A2
8
A110
3 16
7486 6 4 7483
14 C4
2
S415
S32
S26
S19
7486'3 Cout
DataOutput
Input DataB
B3
B2
B1
S=0
12
C0 GND
Truth Table:- 4-BIT Parallel Adder Using 7483 where S=0
Input Data A Input Data B Addition
A4 A3 A2 A1 B4 B3 B2 B1 Cout S4 S3 S2 S1
1 0 0 0 0 0 1 0 0 1 0 1 0
1 0 0 0 1 0 0 0 1 0 0 0 0
0 0 1 0 1 0 0 0 0 1 0 1 0
0 0 0 1 0 1 1 1 0 1 0 0 0
1 0 1 0 1 0 1 1 1 0 1 0 1
0 1 1 0 0 0 1 1 0 1 0 0 1
1 1 1 0 1 1 1 1 1 1 1 0 1
1 0 1 0 1 1 0 1 1 0 1 1 1
11
Input Data A Input Data BSubtraction
A4 A3 A2 A1 B4 B3 B2 B1 Bout S4 S3 S2 S1
1 0 0 0 0 0 1 0 0 0 1 1 0
1 0 0 0 1 0 0 0 0 0 0 0 0
0 0 1 0 1 0 0 0 1 1 0 1 0
0 0 0 1 0 1 1 1 1 1 0 1 0
1 0 1 0 1 0 1 1 1 1 1 1 1
0 1 1 0 0 0 1 1 0 0 0 1 1
1 1 1 0 1 1 1 1 1 1 1 1 1
1 0 1 0 1 1 0 1 1 1 1 0 1
B. IC 7483 as a Parallel Subtractor
Circuit Diagram:A4
VCC
5
OutputCarry
1
Input Data A
B4
1A3
3A2
8
A110
1
7486 3 16
2
4
7486 6 4 7483
14 C4
2
S415
S32
S26
S19
7486'3
Bout
DataOutput
Input DataB
B3
B2
B1
S=1
5
98
7486 710
12
7486 1113
13
C0
12
GND
4-BIT Parallel Subtractor Using 7483 Where S=1
Truth Table:
Note: Bout = 1 for A<B; Bout = 0 for A>B;
Example
4bit adder operation using 7483if control input S=0,addition can be performed
Ex: If↓C0=0
A4 A3 A2 A1=1100B4 B3 B2 B1=0011
then Sum,S4 S3 S2 S1 =1111 and C0 C4 = Cout.
4 bit subtraction operation using 7483 for A>B here S=1A4 A3 A2 A1= 1001B4 B3 B2 B1= 1101 (2's complement) of +3=0011
The end around carry is disregarded 1 0110C0 C4 = Bout = 0
Difference, S4 S3 S2 S1 = 01102's complement method of subtraction can be performed, if S=1(i.e. C0=1).
Consider the above Example A4 A_3 A2_A_1= 1_001 and B4 B3 B2 B1= 0011
1‟s Complement of B4 B3 B2 B1 is B4 B3 B2 B1= 1100
. _A4 A_3 A_2 A_1= 1001
B4 B3 B2 B1= 1100 → (1's complement) of +3 = 0011+1 ← C0=1(S&C0 shorted)
2‟s Complementof
B input = -B
The end around carry is disregarded 1 0110C0 C4 = Bout = 0 +6
4 bit subtraction operation using 7483 for A<B here S=1
_A4 A_3 A_2 A_1= 1110
B4 B3 B2 B1= 0000 → (1's complement) of +15 = 1111+1 ← C0=1(S&C0 shorted)
2‟s Complementof
B input = -B
The end around carry is disregarded 0 1111 → (2's complement) of +1 = 0001C0 C4 = Bout = 1
-1
11
C. BCD To Excess-3 And Vice-Versa Conversion Using 7483 Chip
I. BCD TO EXCESS-3 CONVERTER
Note: S = 0 and B3,B2,B1,B0 = 0011 vary the BCD input at A3,A2,A1,A0.
Circuit Diagram:
Input Data A
B3 = 0
A31
A23
A18
A010
1
7486 3 162
VCC
5
14 C4
E315
E22
E16
E09
X NC
DataOutput
Input DataB B2 = 0
B1 = 1
B0 = 1
S=0
4
7486 6
5
98
748610
12
748613
4 7483
7
11
13 12
C0 GND
Truth Table : BCD to XCS3 using 7483
Consider Constant Value for B3B2B1B0 = 0011 and S=0
BCD Inputs Excess – 3 Outputs
A3 A2 A1 A0 E3 E2 E1 E0
0 0 0 0 0 0 1 1
0 0 0 1 0 1 0 0
0 0 1 0 0 1 0 1
0 0 1 1 0 1 1 0
0 1 0 0 0 1 1 1
0 1 0 1 1 0 0 0
0 1 1 0 1 0 0 1
0 1 1 1 1 0 1 0
1 0 0 0 1 0 1 1
1 0 0 1 1 1 0 0
1 0 1 0 X X X X
1 0 1 1 X X X X
1 1 0 0 X X X X
1 1 0 1 X X X X
1 1 1 0 X X X X
1 1 1 1 X X X X
11
II. EXCESS-3 to BCD CONVERTER
Note: S=1 and B3,B2,B1,B0 = 0011 vary the Excess-3 input at A3(E3),A2(E2),A1(E1),A0(E0).
Circuit Diagram: VCC
Input Data A
B3 = 0
Input Data
A31
A23
A18
A010
1
7486 3 162
4
7486 6 4
5
7483
14 C4
D15
C2
B6
A9
X NC
DataOutput
B B2 = 0
B1 = 1
B0 = 1
S=1
5
98
7486 71012
7486 1113
13
C0
12
GND
Truth Table : XCS3 to BCD using 7483
Consider Constant Value for B3B2B1B0 = 0011 and S=1
Excess-3 Inputs BCD Outputs
E3 E2 E1 E0 A B C D
0 0 1 1 0 0 0 0
0 1 0 0 0 0 0 1
0 1 0 1 0 0 1 0
0 1 1 0 0 0 1 1
0 1 1 1 0 1 0 0
1 0 0 0 0 1 0 1
1 0 0 1 0 1 1 0
1 0 1 0 0 1 1 1
1 0 1 1 1 0 0 0
1 1 0 0 1 0 0 1
Experiment No. 4
BIN A RY T O G R AY CO N V E RT E R AND VICE V E R SA
Aim: – To realize:.i. Binary to Gray Converter using logic gates. ii. Gray to Binary Converter using logic gates.
Components Required: - IC 7486, etc.
Procedure: -
1.Verify that the gates are working properly.
2. Write the proper truth table for the given Binary to Gray converter.
3. Draw Karnaugh maps for each bit of output. Simplify the Karnaugh maps to get
simplified Boolean Expressions.
4. Make connections on the trainer kit as shown in the circuit diagram for the Binary
to Gray converter.
5. Apply the Binary inputs at B3-B0 pins, according to the truth table.
6. Check the outputs at the G3-G0 pins and note them down in the table for the
corresponding inputs.
7. Verify that the outputs match with the expected results.
8. Repeat the procedure to design, test and verify the working of a Grey to Binary
Converter.
A. Binary to Gray Converter.
Truth Table:
Binary Input Gray Code Output
B3 B2 B1 B0 G3 G2 G1 G0
0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1
0 0 1 0 0 0 1 1
0 0 1 1 0 0 1 0
0 1 0 0 0 1 1 0
0 1 0 1 0 1 1 1
0 1 1 0 0 1 0 1
0 1 1 1 0 1 0 0
1 0 0 0 1 1 0 0
1 0 0 1 1 1 0 1
1 0 1 0 1 1 1 1
1 0 1 1 1 1 1 0
1 1 0 0 1 0 1 0
1 1 0 1 1 0 1 1
1 1 1 0 1 0 0 1
1 1 1 1 1 0 0 0
Karnaugh Maps:
For G3: For G2:
G3 = B3
Circuit:
For G1: For G0:
B. Gray to Binary Converter
Truth Table
Gray Code Input Binary Output
G3 G2 G1 G0 B3 B2 B1 B0
0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1
0 0 1 1 0 0 1 0
0 0 1 0 0 0 1 1
0 1 1 0 0 1 0 0
0 1 1 1 0 1 0 1
0 1 0 1 0 1 1 0
0 1 0 0 0 1 1 1
1 1 0 0 1 0 0 0
1 1 0 1 1 0 0 1
1 1 1 1 1 0 1 0
1 1 1 0 1 0 1 1
1 0 1 0 1 1 0 0
1 0 1 1 1 1 0 1
1 0 0 1 1 1 1 0
1 0 0 0 1 1 1 1
Karnaugh Maps:
For B3: For B2:
B3 = G3
Circuit:
For B1: For B0:
Experiment No. 5
MUX / DEMUX F O R ARI TH ME T I C C IRCU I TS Aim: – To study IC 74153 and 74139 and to implement arithmetic circuits with them.
Components Required: - IC 74153, IC 74139, IC 7404, IC 7400, IC 7420,etc.
Procedure –
A. For MUX IC 74153
1.The Pin [16] is connected to + Vcc and Pin [8] is connected to ground.
2. The inputs are applied either to ‘A’ input or ‘B’ input.
3.If MUX ‘A’ has to be initialized, EA is made low and if MUX ‘B’ has to be
initialized, EB is made low.
4. Based on the selection lines one of the inputs will be selected at
the output, and thus the truth table is verified.
5.In case of half adder using MUX, apply constant inputs at (I0a, I1a, I2a,
I3a)and (I0b, I1b, I2b and I3b) as shown.
6.The corresponding values of select input lines, A and B (S1 and S0)
are changed as per table and the output is taken at Za as sum
and Zb as carry.
7.In this case, the inputs A and B are varied. Making Ea and Eb
zero andthe output is taken at Za, and Zb.
8.In case of Half Subtractor, connections are made according to the
circuit, Inputs are applied at A and B as shown, and outputs are
taken at Za (Difference) and Zb (Borrow). Verify outputs.
9.In full adder using MUX, the inputs are applied at Cn-1, An and
Bn according to the truth table. The corresponding outputs are taken
at Sn (pin Za) and Cn (pin Zb) and are verified according to the truth
table.
10. In full subtractor using MUX, the inputs are applied at Cn-1, An
and Bn according to the truth table. The corresponding outputs
are taken at pin Za(Difference) and pin Zb(Borrow) and are verified
according to the truth table.
Half Adder Using 74153 Half Subtractor using 74153
Truth Table:
Inputs Half Adder Outputs Half Subtractor Outputs
A B Sum Carry Diff Borrow
0 0 0 0 0 0
0 1 1 0 1 1
1 0 1 0 1 0
1 1 0 1 0 0
Full Adder Using 74153 Full Subtractor using 74153
Truth Tables for Full Adder/Subtractor using 74153
Inputs Full Adder Outputs Full Subtractor Outputs
A B Cin/Bin S Cout D Bout
0 0 00 0 0 0
0 0 11 0 1 1
0 1 01 0 1 1
0 1 10 1 0 1
1 0 01 0 1 0
1 0 10 1 0 0
1 1 00 1 0 0
1 1 11 1 1 1
Procedure –
B. For DEMUX IC 74139
1. The Pin [16] is connected to + Vcc and Pin [8] is connected to ground.2. The inputs are applied either to ‘A’ input or ‘B’ input.3. If DEMUX ‘A’ has to be initialized, EA is made low and if DEMUX ‘B’
has to be initialized, EB is made low.4. Based on the selection lines one of the inputs will be selected at the
set of outputs, and thus the truth table is verified.5. In case of half adder using DEMUX,Ea is set to 0, the corresponding
values of select input lines, A and B (S1a and S0a) are changed as per table and the output is taken at Sum and Carry. Verify outputs.
6. In case of Half Subtractor, connections are made according to the circuit, Inputs are applied at A and B as shown, and outputs are taken at Differenceand Borrow. Verify outputs.
7. In full adder using DEMUX, the inputs are applied at Cn-1, An and Bn according to the truth table. The corresponding outputs are taken at Sum and Carry, and are verified according to the truth table.
8. In full subtractor using DEMUX, the inputs are applied at Cn-1, An
and Bn according to the truth table. The corresponding outputs are
taken at Difference and Borrow as shown, and are verified according to the truth table.
Half Adder Using 74139
Half Subtractor Using 74139
Truth Tables:
Inputs Half Adder Outputs Half Subtractor Outputs
A B Sum Carry Diff Borrow
0 0 0 0 0 0
0 1 1 0 1 1
1 0 1 0 1 0
1 1 0 1 0 0
Full Adder Using 74139
Full Subtractor Using 74139
Truth Tables:
Inputs Full Adder Outputs Full Subtractor Outputs
A B Cin/Bin S Cout D Bout
0 0 00 0 0 0
0 0 11 0 1 1
0 1 01 0 1 1
0 1 10 1 0 1
1 0 01 0 1 0
1 0 10 1 0 0
1 1 00 1 0 0
1 1 11 1 1 1
Inputs Outputs
A B A>B A=B A<B
0 0 0 1 0
0 1 0 0 1
1 0 1 0 0
1 1 0 1 0
Experiment No. 6
ONE/T W O B I TC O MPAR A TOR AN D IC 74 8 5
Aim: – To verify the truth tables for one bit and two bit comparators after constructing them with basic logic gates, and to study the working of IC 7485.
Components Required: - IC 7404, IC 7408, IC 7486, IC 7432, IC 7485, etc.
Procedure –
A. Comparators Using Logic Gates:
1.Verify the working of the logic gates.
2.Make the connections as per the respective circuit diagrams.
3.Switch on Vcc.
4.Apply the inputs as per the truth tables.
5.Check the outputs and verify that they are according to the truth tables.
B. Study of IC 7485:
1.Write the truth table for an4-bit comparator.
2. Connect pin 16 to Vcc and pin 8 to GND for the ICs.
3.Apply the two inputs as shown; making sure that the MSB and LSB is correctly
connected.
4. Outputs are recorded at pin 2 (A<B), pin 4 (A>B), pin 3 (A=B) pins and are
verified as being according to the truth table.
A. One-Bit Comparator:
Circuit : Truth Table: 1bit Comparator
B. Two-Bit Comparator:
Truth Table : 2bit Comparator
A1 A0 B1 B0 A > B A = B A < B
0 0 0 0 0 1 0
0 0 0 1 0 0 1
0 0 1 0 0 0 1
0 0 1 1 0 0 1
0 1 0 0 1 0 0
0 1 0 1 0 1 0
0 1 1 0 0 0 1
0 1 1 1 0 0 1
1 0 0 0 1 0 0
1 0 0 1 1 0 0
1 0 1 0 0 1 0
1 0 1 1 0 0 1
1 1 0 0 1 0 0
1 1 0 1 1 0 0
1 1 1 0 1 0 0
1 1 1 1 0 1 0
Karnaugh Maps:
For A>B: For A<B
For A=B
Circuit:
C. 4-Bit comparator using IC 7485
Pin Diagram:
Truth Table: 4bit Comparator
Input A Input B Output
A3 A2 A1 A0 B3 B2 B1 B0 A>B A<B A=B
0 0 0 0 0 0 0 1 0 1 0
0 1 0 1 0 0 1 1 1 0 0
1 0 1 0 1 0 1 0 0 0 1
0 0 1 1 0 1 1 0 0 1 0
0 1 0 0 1 0 0 0 0 1 0
1 1 0 1 1 0 1 1 1 0 0
0 1 1 0 0 1 1 0 0 0 1
1 1 1 1 1 1 1 0 1 0 0
Experiment No. 7
D E CODER CHIP FOR L ED DIS P L A Y
Aim: – Tostudy the use of a Decoder Chip (IC 7447) to drive a LED Display.
Components required: - IC 7447, 7-segment LED Display, etc.
Procedure: -
1. Test and verify that all the segments of the LED Display are working.
2. Make the circuit connections as shown in the circuit diagram.
3. Connect Pin 16 to Vcc and Pin 8 to GND.
4. Connect the input pinsof the 7-segment LED Display to the respective pins (A3-A0)
of the 7447 BCD to 7-Segment decoder driver chip.
5. Give the different BCD inputs according to the truth table, and observe the Decimal
outputs displayed on the 7-segment LCD Display.
6. Verify that the outputs match the expected results in the truth tables.
IC 7447 Pin Diagram
Circuit Diagram:
Output Table:
BCD inputs segment outputs displayD C B A a b c d e f g0 0 0 0 1 1 1 1 1 1 0
0 0 0 1 0 1 1 0 0 0 0
0 0 1 0 1 1 0 1 1 0 1
0 0 1 1 1 1 1 1 0 0 1
0 1 0 0 0 1 1 0 0 1 1
0 1 0 1 1 0 1 1 0 1 1
0 1 1 0 0 0 1 1 1 1 1
0 1 1 1 1 1 1 0 0 0 0
1 0 0 0 1 1 1 1 1 1 1
1 0 0 1 1 1 1 0 0 1 1
7-segment LED Display Schematic
Experiment No. 8
P R I O RITY ENC O D E R
Aim: – Tostudy the use of a 10-line-to-4-Line Priority Encoder Chip (IC 74147).
Components Required: - IC 74147, etc.
Procedure: -
1. Make the connections as shown in the circuit diagram.
2. Connect Pin 16 of the IC to Vcc and Pin 8 to GND.
3. Connect the pins designated Inputs 1 through 9, to the input switches of the trainer kit.
4. Connect the Output pins designated A, B, C, D to the LED indicators of the trainer kit.
5. Provide the inputs to the encoder chip as shown in the truth table.
6. Observe the outputs on the LED indicators, and note down the results for the
respective inputs.
7. Verify that the outputs are as shown in the truth table.
IC 74147 Pin Diagram
Truth Table:
Decimal Input BCD Output DecimalValue1 2
1 3
1 4 1
5 1
6 1
7 1
8 1
9 D C 1
B 1
A1 1 1 1 00 1 1 1 1 1 1 1 1 1 1 1 0 1X 0 1 1 1 1 1 1 1 1 1 0 1 2X X 0 1 1 1 1 1 1 1 1 0 0 3X X X 0 1 1 1 1 1 1 0 1 1 4X X X X 0 1 1 1 1 1 0 1 0 5X X X X X 0 1 1 1 1 0 0 1 6X X X X X X 0 1 1 1 0 0 0 7X X X X X X X 0 1 0 1 1 1 8X X X X X X X X 0 0 1 1 0 9
Experiment No. 9
STUDY O F FLIP-FLOPS
Aim: – To study and verify the truth tables for J-K Master Slave Flip Flop, T-type and D- Type Flip-Flops.
Components Required: - IC 7410, IC 7400, etc.
Procedure: -
1. Make the connections as shown in the respective circuit diagrams.
2. Apply inputs as shown in the respective truth tables, for each of the flip-flop circuits.
3. Check the outputs of the circuits; verify that they match that of the respective truth
tables.
A. J-K Master-Slave Flip-Flop
Circuit:
Truth Table :
Preset Clear J K Clock Status
0 1 X X X 1 0 Set
1 0 X X X 0 1 Reset
1 1 0 0 No Change
1 1 0 1 0 1 Reset
1 1 1 0 1 0 Set
1 1 1 1 Toggle
B. T-Type Flip-Flop
Circuit:
Truth Table :
Preset Clear T Clock
1 1 0
1 1 1
C. D-Type Flip-Flop
Circuit:
Truth Table:
Preset Clear D Clock
1 1 0 0 1
1 1 1 1 0
Experiment No. 10
STUDY O F COUNTE R S
Aim: – Realization of 3-bit counters as a sequential circuit and Mod-N counter Design (7476,7490, 74192, 74193)
Components Required: - IC 7476, IC 7490, IC 74192, IC 74193, IC 7400, IC 7408, IC7416, IC 7432, etc.
Procedure: -
A. Counter Circuits using IC 7476
1. Make the connections as shown in the respective circuit diagrams.
2. Clock inputs are applied one by one at the clock I/P, and the outputs are
observed at QA, QB and QC pins of the 7476 ICs.
3. Verify that the circuit outputs match those indicated by the truth tables.
B. Study of Counters IC 74192, IC 74193
1. Connections are made as shown in the respective circuit diagrams, except for
the connection from the output of the NAND gate to the load input.
2. The data (0011) = 3 is made available at the data input pins designated A, B, C
and D respectively.
3. The Load pin is made LOW so that the data 0011 appears at QD, QC, QB and
QA respectively.
4. Now, the output of the NAND gate is connected to the Load input pin.
5. Clock pulses are applied to the “Count Up” pin, and truth table is verified for that condition.
6. Next, the data (1100) =12 (for 12 to 5 counter) is applied at A, B, C and D and
the same procedure as explained above, is performed.
7. IC 74192 and IC 74193 have the same pin configurations. 74192 can be
configured to count between 0 and 9 in either direction. Starting value can be
any number between 0 and 9.
A. 3-bit Asynchronous Up Counter
Circuit Diagram:
Timing Diagram:
Truth Table:
Clock QC QB QA
0 0 0 0
1 0 0 1
2 0 1 0
3 0 1 1
4 1 0 0
5 1 0 1
6 1 1 0
7 1 1 1
8 0 0 0
9 0 0 1
Dept. Of ECE. 40 BTL Institute of Technology & Management
B. 3-bit Asynchronous Down Counter
Circuit Diagram:
Timing Diagram:
Truth Table:
Clock QC QB QA
0 1 1 1
1 1 1 0
2 1 0 1
3 1 0 0
4 0 1 1
5 0 1 0
6 0 0 1
7 0 0 0
8 1 1 1
9 1 1 0
Dept. Of ECE. 41 BTL Institute of Technology & Management
C. Mod-5 Asynchronous Counter
Circuit:
Timing Diagram:
Truth Table:
Clock QC QB QA
0 0 0 0
1 0 0 1
2 0 1 0
3 0 1 1
4 1 0 0
5 0 0 0
Dept. Of ECE. 42 BTL Institute of Technology & Management
D. Mod-3 Asynchronous Counter
Circuit:
Timing Diagram:
Truth Table:
Clock QC QB QA
0 0 0 0
1 0 0 1
2 0 1 0
3 0 0 0
4 0 0 1
5 0 1 0
Dept. Of ECE. 43 BTL Institute of Technology & Management
E. 3-bit Synchronous Counter
Circuit:
Timing Diagram:
Truth Table:
Clock QC QB QA
0 0 0 0
1 0 0 1
2 0 1 0
3 0 1 1
4 1 0 0
5 1 0 1
6 1 1 0
7 1 1 1
8 0 0 0
9 0 0 1
Dept. Of ECE. 44 BTL Institute of Technology & Management
F. 4-bit Ripple Counter
Circuit:
Truth Table:
CLK QD QC QB QA
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
10 1 0 1 0
11 1 0 1 1
12 1 1 0 0
13 1 1 0 1
14 1 1 1 0
15 1 1 1 1
Dept. Of ECE. 45 BTL Institute of Technology & Management
G. Mod-10 Ripple Counter
Circuit:
Truth Table
CLK QD QC QB QA
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
10 0 0 0 0
Dept. Of ECE. 46 BTL Institute of Technology & Management
H. Decade Counter (using IC 7490)
Circuit:
Truth Table:
Clock QD QC QB QA
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
10 0 0 0 0
Dept. Of ECE. 47 BTL Institute of Technology & Management
I. Mod-8 Counter (Using IC 7490)
Circuit:
Truth Table:
Clock QD QC QB QA
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 0 0 0 0
9 0 0 0 1
Dept. Of ECE. 48 BTL Institute of Technology & Management
J. Presettable counter using IC 74192/IC 74193 to count up from 3 to 8
Circuit:
Truth Table:
Clock QD QC QB QA Decimal
0 0 0 1 1 3
1 0 1 0 0 4
2 0 1 0 1 5
3 0 1 1 0 6
4 0 1 1 1 7
5 1 0 0 0 8
6 0 0 1 1 3
7 0 1 0 0 4
Dept. Of ECE. 49 BTL Institute of Technology & Management
K. Presettable counter using IC 74192/74193 to count down from 5 to 12
Circuit:
Implementation of 4-Input OR gate:
Truth Table:
Clock QD QC QB QA Decimal
0 0 1 0 1 5
1 0 1 1 0 6
2 0 1 1 1 7
3 1 0 0 0 8
4 1 0 0 1 9
5 1 0 1 0 10
6 1 0 1 1 11
7 1 1 0 0 12
8 0 1 0 1 5
9 0 1 1 0 6
Dept. Of ECE. 50 BTL Institute of Technology & Management
Experiment No. 11
STUDY O F SH I FT R E G IS TE R S
Aim: – To study IC 74S95, and the realization of Shift left, Shift right, SIPO, SISO, PISO, PIPO operations using the same.
Components Required: - IC 7495, etc.
Procedure: -
A. Serial In-Parallel Out (Left Shift):
1. Make the connections as shown in the respective circuit diagram.
2. Make sure the 7495 is operating in Parallel mode by ensuring Pin 6 (Mode M)
is set to HIGH, and connect clock input to Pin 8 (Clk 2).
3. Apply the first data at pin 5 (D) and apply one clock pulse. We observe that
this data appears at pin 10 (QD).
4. Now, apply the second data at D. Apply a clock pulse. We now observe that
the earlier data is shifted from QD to QC, and the new data appears at QD.
5. Repeat the earlier step to enter data, until all bits are entered one by one.
6. At the end of the 4th clock pulse, we notice that all 4 bits are available at the
parallel output pins QA (MSB), QB, QC, QD (LSB).
7. Enter more bits to see there is a left shifting of bits with each succeeding clock
pulse.
B. Serial In-Parallel Out (Right Shift):
1. Make the connections as shown in the respective circuit diagram.
2. Make sure the 7495 is operating in SIPO mode by ensuring Pin 6 (Mode M) is
set to LOW, and connect clock input to Pin 9 (Clk 1).
3. Apply the first data at pin 1 (SD1) and apply one clock pulse. We observe that
this data appears at pin 13 (QA).
4. Now, apply the second data at SD1. Apply a clock pulse. We now observe that
the earlier data is shifted from QA to QB, and the new data appears at QA.
5. Repeat the earlier step to enter data, until all bits are entered one by one.
6. At the end of the 4th clock pulse, we notice that all 4 bits are available at the
parallel output pins QA through QD.
7. Enter more bits to see there is a right shifting of bits with each succeeding
clock pulse.
Dept. Of ECE. 51 BTL Institute of Technology & Management
C. Serial In-Serial Out Mode:
1. Connections are made as shown in the SISO circuit diagram.
2. Make sure the 7495 is operating in SIPO mode by ensuring Pin 6 (Mode) is set
to LOW, and connect clock input to Clk 1(Pin 9).
3. The 4 bits are applied at the Serial Input pin (Pin 1), one by one, with a clock
pulse in between each pair of inputs to load the bits into the IC.
4. At the end of the 4th clock pulse, the first data bit, „d0‟ appears at the output pin
QD.
5. Apply another clock pulse, to get the second data bit „d1‟ at QD. Applying yet
another clock pulse gets the third data bit „d2‟ at QD, and so on.
6. Thus we see the IC 7495 operating in SISO mode, with serially applied inputs
appearing as serial outputs.
D. Parallel In-Serial Out Mode:
1. Connections are made as shown in the PISO circuit diagram.
2. Now apply the 4-bit data at the parallel input pins A, B, C, D (pins 2 through
5).
3. Keeping the mode control M on HIGH, apply one clock pulse. The data applied
at the parallel input pins A, B, C, D will appear at the parallel output pins QA,
QB, QC, QDrespectively.
4. Now set the Mode Control M to LOW, and apply clock pulses one by one.
Observe the data coming out in a serial mode at QD.
5. We observe now that the IC operates in PISO mode with parallel inputs being
transferred to the output side serially.
E. Parallel In-Parallel Out Mode:
1. Connections are made as shown in the PIPO mode circuit diagram.
2. Set Mode Control M to HIGH to enable Parallel transfer.
3. Apply the 4 data bits as input to pins A, B, C, D.
4. Apply one clock pulse at Clk 2 (Pin 8).
5. Note that the 4 bit data at parallel inputs A, B, C, D appears at the parallel
output pins QA, QB, QC, QDrespectively.
ClockSerial
I/PQA QB QC QD
1 1 X X X 1
2 0 X X 1 0
3 1 X 1 0 1
4 1 1 0 1 1
ClockSerial
I/PQA QB QC QD
1 1 1 X X X
2 0 0 1 X X
3 1 1 0 1 X
4 1 1 1 0 1
Dept. Of ECE. 52 BTL Institute of Technology & Management
IC 7495 Pin Diagram:
A. SIPO Mode (Left Shift)
Circuit: Truth Table:
1
B. SIPO MODE (Right Shift)
Circuit: Truth Table:
ClockSerial
I/PQA QB QC QD
1 d0=0 0 X X X
2 d1=1 1 0 X X
3 d2=1 1 1 0 X
4 d3=1 1 1 1 0=d0
5 X X 1 1 1=d1
6 X X X 1 1=d2
7 X X X X 1=d3
Mode Clk Parallel I/P Parallel O/P
A B C D QA QB QC QD
1 1 1 0 1 1 1 0 1 1
0 2 X X X X X 1 0 1
0 3 X X X X X X 1 0
0 4 X X X X X X X 1
Dept. Of ECE. 53 BTL Institute of Technology & Management
C. SISO Mode
Circuit: Truth Table:
D. PISO Mode
Circuit: Truth Table:
Clk Parallel I/P Parallel O/P
A B C D QA QB QC QD
1 1 0 1 1 1 0 1 1
Dept. Of ECE. 54 BTL Institute of Technology & Management
E. PIPO Mode
Circuit: Truth Table:
Mode Clock QA QB QC QD
1 1 1 0 0 0
0 2 0 1 0 0
0 3 0 0 1 0
0 4 0 0 0 1
0 5 1 0 0 0
0 6 0 1 0 0
Dept. Of ECE. 55 BTL Institute of Technology & Management
Experiment No. 12
RING C O U N TER /JO H NSON COU N TER
Aim: – To design and study the operation of a ring counter and a Johnson Counter.
Components Required: - IC 7495, IC 7404, etc.
Procedure: -
1. Make the connections as shown in the respective circuit diagram for the Ring
Counter.
2. Apply an initial input (1000) at the A, B, C, D pins respectively.
3. Keep Select Mode = HIGH (1) and apply one clock pulse.
4. Next, Select Mode = LOW (0) to switch to serial mode and apply clock pulses.
5. Observe the output after each clock pulse, record the observations and verify that
they match the expected outputs from the truth table.
6. Repeat the same procedure as above for the Johnson Counter circuit and verify its
operation.
A. Ring Counter
Circuit: Truth Table:
Mode Clock QA QB QC QD
1 1 1 0 0 0
0 2 1 1 0 0
0 3 1 1 1 0
0 4 1 1 1 1
0 5 0 1 1 1
0 6 0 0 1 1
0 7 0 0 0 1
0 8 0 0 0 0
0 9 1 0 0 0
0 10 1 1 0 0
Dept. Of ECE. 56 BTL Institute of Technology & Management
B. Johnson Counter
Circuit: Truth Table:
Dept. Of ECE. 57 BTL Institute of Technology & Management
Experiment No. 13
SEQUE N CE GEN E RA T OR
Aim: – To design and study the operation of a Sequence Generator.
Components Required: - IC 7495, IC 7486, etc.
Theory: -
In order to generate a sequence of length „S‟, it is necessary to use at least„N‟ number ofFlip-flops, in order to satisfy the condition .
The given sequence length S = 15Therefore, N = 4
Note: There is no guarantee that the given sequence can be generated by 4 flip-flops. If the sequence is not realizable by 4 flip-flops, we need to use 5 flip-flops, and so on.
Procedure:-
1. Truth table is constructed for the given sequence, and Karnaugh maps are drawn in
order to obtain a simplified Boolean expression for the circuit.
2. Connections are made as shown in the circuit diagram.
3. Mode M is set to LOW (0), and clock pulses are fed through Clk 1 (pin 9).
4. Clock pulses are applied at CLK 1 and the output values are noted, and checked
against the expected values from the truth table.
5. The functioning of the circuit as a sequence generator is verified.
Circuit:
Clock QA QB QC QD
O/p
D
1 1 1 1 1 0
2 0 1 1 1 0
3 0 0 1 1 0
4 0 0 0 1 1
5 1 0 0 0 0
6 0 1 0 0 0
7 0 0 1 0 1
8 1 0 0 1 1
9 1 1 0 0 0
10 0 1 1 0 1
11 1 0 1 1 0
12 0 1 0 1 1
13 1 0 1 0 1
14 1 1 0 1 1
15 1 1 1 0 1
1 1 1
1 1
1
Dept. Of ECE. 58 BTL Institute of Technology & Management
Truth Table: Karnaugh Map:
Map
Value
15
7
3
1
8
4
2
9
12
6
11
5
10
13
14
Dept. Of ECE. 59 BTL Institute of Technology & Management
Syllabus
LOGIC DESIGN LAB (Common to
EC/TC/EE/IT/BM/ML)
Sub Code :10ESL38 IA Marks : 25
Hrs/ Week : 03 Exam Hours : 03
Total Hrs.: Exam Marks : 50
NOTE: Use discrete components to test and verify the logic gates. LabView can be used for
designing the gates along with the above.
1. Simplification, realization of Boolean expressions using logic gates/Universal gates.
2. Realization of Half/Full adder and Half/Full Subtractors using logic gates.
3. (i)Realization of parallel adder/Subtractors using 7483 chip
(ii) BCD to Excess-3 code conversion and vice versausing 7483 chip.
4. Realization of Binary to Gray code conversion and vice versa
5. MUX/DEMUX – use of 74153, 74139 for arithmetic circuits and code converter.
6. Realization of One/Two bit comparator and study of 7485 magnitude comparator.
7. Use of Decoder chip to drive LED display.
8. Use of IC 74147 as Priority encoder.
9. Truth table verification of Flip-Flops:
(i) JK Master slave
(ii) T type
(iii) D type.
10. Realization of 3 bit counters as a sequential circuit and MOD – N counter design
(7476, 7490, 74192,74193).
11. Shift left; Shift right, SIPO, SISO, PISO, PIPO operations using 74S95.
12. Wiring and testing Ring counter/Johnson counter.
13. Wiring and testing of Sequence generator.
http://ww w .sc r ibd.co m /doc/62491691/Logi c -D e sig n -Lab -M anua l -10E S L38-3rd-s e m -2011
Dept. Of ECE. 60 BTL Institute of Technology & Management
1. Define a logic gate.2. What are basic gates?
Possible Viva Questions
3. Why NAND and NOR gates are called as universal gates.4. State De-morgans theorem5. Give examples for SOP and POS6. Explain how transistor can be used as NOT gate7. Explain AND and OR gate using diodes8. Realize logic gates using NAND and NOR gates only9. Define LSI, MSI , SSI10. List the applications of EX-OR and EX~NOR gates11. What is a truth table?12. What is a half adder?13. Differentiate between half adder and half subtractor14. What is a full adder?15. Differentiate between combinational and sequential circuits. Give examples16. Give the applications of combinational and sequential circuits17. Give the block diagram of sequential circuits18. Define flip flop19. What is an excitation table/functional table20. Differentiate between flip flop and latch21. What is race around condition?22. How do you eliminate race around condition23. Give the block diagram of parallel adders24. What are BCD Give their applications or uses25. What is minterm and maxterm?26. Explain the working of 7483 adder chip. Explain how it can be used as EX-3 to
BCD conversion and vice versa27. Define multiplexer/ data selector28. What is a Demultiplexer?29. Give the applications of mux and demux30. What is a encoder and decoder31. Compare mux and encoder32. Compare demux and decoder33. What is a priority encoder?34. What is a code converter?35. What are counters? Give their applications36. Compare synchronous and asynchronous counters37. What is a ripple counter?38. What is modulus of a number?39. What is a shift register?40. Explain how a shift register can be used as ring and johnson counter41. Give the applications of johnson and ring counters42. What is an up counter and down counter?43. What is common cathode and common anode LED?44. What is LCD and LED.45. What is a static and a dynamic display.46. List the types of LCD's and LED's.47. What does LS stand for, in 74LS00?48. Mention the different logic families.49. Which is the fastest logic?