8/10/2019 4102 NDT Notes.pdf
1/14
8/10/2019 4102 NDT Notes.pdf
2/14
Used to locate cracks,porosity, and other
defects that break the
surface of a material
and have enoughvolume to trap and
hold the penetrantmaterial. Liquidpenetrant testing is
used to inspect large
areas very efficiently
and will work on most
nonporous materials.
Used to inspectferromagnetic
materials (those that
can be magnetized)
for defects that resultin a transition in the
magnetic permeabilityof a material.Magnetic particle
inspection can detect
surface and near
surface defects.
Used to locate surfaceand subsurface defects
in many materials
including metals,
plastics, and wood.Ultrasonic inspection
is also used tomeasure the thicknessof materials and
otherwise characterize
properties of material
based on sound
velocity andattenuation
measurements.
Used to detect surfaceand near-surface flaws
in conductive
materials, such as the
metals. Eddy currentinspection is also used
to sort materials basedon electricalconductivity and
magnetic
permeability, and
measures the
thickness of thinsheets of metal and
nonconductive
coatings such as paint.
Used to inspect almostany material for
surface and subsurface
defects. X-rays can
also be used to locatesand measures internal
features, confirm thelocation of hiddenparts in an assembly,
and to measure
thickness of materials.
Main Advantages
Large surface areas or
large volumes of
parts/materials can beinspected rapidly and
at low cost.
Parts with complex
geometry are routinelyinspected.
Indications are
produced directly on
surface of the part
providing a visualimage of the
discontinuity.
Equipment investment
is minimal.
Large surface areas of
complex parts can be
inspected rapidly.
Can detect surface andsubsurface flaws.
Surface preparation is
less critical than it is
in penetrantinspection.
Magnetic particle
indications are
produced directly onthe surface of the part
and form an image of
the discontinuity.
Equipment costs are
relatively low.
Depth of penetration
for flaw detection or
measurement issuperior to other
methods.
Only single sided
access is required.
Provides distanceinformation.
Minimum part
preparation is
required.
Method can be usedfor much more than
just flaw detection.
Detects surface and
near surface defects.
Test probe does not
need to contact thepart.
Method can be used
for more than flaw
detection.
Minimum partpreparation is
required.
Can be used to inspect
virtually all materials.
Detects surface and
subsurface defects.
Ability to inspectcomplex shapes and
multi-layered
structures withoutdisassembly.
Minimum part
preparation is
required.
Disadvantages
Detects only surface
breaking defects.
Surface preparation is
critical as
contaminants canmask defects.
Requires a relatively
smooth and nonporous
surface.
Post cleaning isnecessary to remove
Only ferromagnetic
materials can be
inspected.
Proper alignment of
magnetic field anddefect is critical.
Large currents are
needed for very large
parts.
Requires relatively
Surface must be
accessible to probe
and couplant.
Skill and training
required is moreextensive than other
technique.
Surface finish and
roughness caninterfere with
inspection.
Only conductive
materials can be
inspected.
Ferromagnetic
materials requirespecial treatment to
address magnetic
permeability.
Depth of penetrationis limited.
Flaws that lie parallel
Extensive operator
training and skill
required.
Access to both sides
of the structure isusually required.
Orientation of the
radiation beam to non-
volumetric defects iscritical.
Field inspection of
8/10/2019 4102 NDT Notes.pdf
3/14
chemicals.
Requires multiple
operations under
controlled conditions.
Chemical handlingprecautions are
necessary (toxicity,
fire, waste).
smooth surface.
Paint or other
nonmagnetic
coverings adversely
affect sensitivity.
Demagnetization and
post cleaning isusually necessary.
Thin parts may bedifficult to inspect.
Linear defects
oriented parallel to the
sound beam can go
undetected.
Reference standardsare often needed.
to the inspectionprobe coil winding
direction can go
undetected.
Skill and training
required is moreextensive than other
techniques.
Surface finish and
roughness mayinterfere.
Reference standards
are needed for setup.
thick section can betime consuming.
Relatively expensive
equipment investment
is required.
Possible radiation
hazard for personnel.
Penetrant
Testing
Magnetic Particle
Testing
Ultrasonic
Testing
Eddy Current
Testing
Radiographic
Testing
8/10/2019 4102 NDT Notes.pdf
4/14
NONDESTRUCTIVE TESTING
IN THE AEROSPACE INDUSTRY
How essential is nondestructive testing (NDT) to
airplanes?
In the aerospace industry, as with other transportation
industries, NDT can make the difference between lifeand death. Aircraft components are inspected before
they are assembled into the aircraft and then they are
periodically inspected throughout their useful life.Aircraft parts are designed to be as light as possible
while still performing their intended function. This
generally means that components carry very high loadsrelative to their material strength and small flaws can
cause a component to fail. Since aircraft are cycled(loaded and unloaded) as they fly, land, taxi, and
pressurize the cabin, many components are prone tofatigue cracking after some length of time. If you are unfamiliar with the term "fatigue cracking" think
about what happens when you bend a paper clip or piece of wire back and forth ...eventually it will
break. Even parts that are loaded well below the level that causes them to deform can develop fatiguecracks after being cycled for a long time. This is what happens in aircraft. After they are used for a
while, fatigue cracks start growing in some of their parts. Cracking can also occur due to other things
like a lightning strike. Aircraft have some protection against lightning strikes but occasionally theyoccur and can results in cracks forming at the strike location like the one shown in the picture.
Another problem that aircraft have is that they are under the constant attack of corrosion. When an
aircraft lands and the door is opened, the inside of the plane often fills with warm moist air. When the
plane takes flight, and reaches altitude, the skin of the aircraft becomes very cold due to the temperature
8/10/2019 4102 NDT Notes.pdf
5/14
of the outside air. This cause the moisture held by the air inside the cabin to condense on the inside of
the aircraft skin. The water will collect at low areas and serve as the electrolyte needed for corrosion to
occur.
The good news is that aircraft are designed to withstand a certain amount of damage from
cracking and corrosion without cause for concern, and NDT inspectors are trained to find the
damage before it becomes a major problem.The rigorous process used to design aircraft either allow
for a certain amount of damage to occur before a part fails, or in many cases, a part can fail completelyand performance of the aircraft will not be affected. The job of the NDT inspector is to find the damage
while it is within acceptable limits.
What kind of NDT techniques are used to ensure the safety of the airplane?
Over 80 percent of the inspections done to an aircraft are visual inspections. At regular intervals
inspectors look at various component of the aircraft for signs of damage. During heavy maintenancework, much of the interior of the aircraft is stripped out so inspectors can look for damage on the inside
surface of the fuselage. However, not all areas of the aircraft can be accessed for visual inspection and
not all damage can be detected by visual means. This is were NDT plays a critical role in thoroughly
inspecting airplanes.
NDT methods allow inspectors to inspect areas of the plane that would
otherwise be uninspectable without disassembling structure to gainaccess to the internal areas. NDT methods also allow inspectors to
detect damage that is too small to be detected by visual means. Eddy
current and ultrasonic inspection methods are used extensively to
locate tiny cracks that would otherwise be undetectable. Thesetechniques are also used to measure the thickness of the aircraft skin
from the outside and detect metal thinning from corrosion on the
inside surface of the skin. X-ray techniques are used to find defects
buried deep within the structure and to locate areas were water haspenetrated into certain structure. Obviously, this task requires trained
professionals who are capable of performing a variety of different
NDT techniques to get a complete and accurate status of the airplane.
There is no question that the success of the airplane industry is
dependent on NDT. Without NDT, the cost of maintaining and flying
in airplanes would increase dramatically, while the safety of flyingwould decrease. When people step into an airplane they trust that it
will get them to their destination with as little turbulence as possible.
NDT plays a vital role in keeping air travel one of the safest modes of transportation.
8/10/2019 4102 NDT Notes.pdf
6/14
BRIDGE INSPECTION
The US has 578,000 highway bridges, which are the lifelines of US commerce. The average life span ofhighway bridges is about 70 years and the majority of
bridges currently in use were built after 1945. However,
significant environmental damage requiring repair typically
occurs before the average bridge reaches mid-life.Corrosion, cracking and other damage can all affect a
bridge's load carrying capacity. Therefore, all of theelements that directly affect performance of the bridge
including the footing, substructure, deck, and
superstructure must be periodically inspected or monitored.
Visual inspection is the primary NDE method used toevaluate the condition of the majority of the nation's
highway bridges. Inspectors periodically (about every two
years) pay each bridge a visit to assess its condition. However, it is not uncommon for a fisherman,canoeist and other passerby to alert officials to major damage that may have occurred between
inspections.
The potential penalties for ineffective inspection of bridges canbe very severe. Instances of major bridge collapse are very rare,
but the results are truly catastrophic. The collapse of the Silver
Bridge in 1967 resulted in loss of 47 lives. The bridge connected
Point Pleasant, West Virginia and Gallipolis,Ohio over the OhioRiver. The cost of this disaster was 175 million dollars but some
experts estimate the same occurrence today would cost between
2.1 and 5.6 billion dollars. Furthermore, these cost figures do nottake into account factors such as loss of business resulting from
loss of access or detours, the cost resulting from blockage of a
major river shipping channel, and potential environmental
damage due to hazardous materials being transported over the bridge at the time of collapse.
The consequences of ineffective bridge inspection are usually not as severe as those at Silver Bridge.
However, repair and retrofit costs on bridges represent a very significant portion of a state's
transportation budget. In the future, replacement of a bridge will become an increasingly unattractivealternative. Growing construction costs, increased losses due to traffic disruption during repair or
replacement, and continuing tight budgets will force life extension to be the only viable alternative for
our aging bridges.
Fatigue cracking and corrosion will become
increasingly important considerations as we go
beyond the 75 year life expectancy and currentvisual inspection techniques will not suffice. The life
extension approach will require increased use of
NDE in a coordinated effort to obtain reliability
assurance for these structures. NDE techniques suchas magnetic particle inspection and ultrasonic
inspection are being used with greater frequency.
One of the newer NDE technologies being used is
8/10/2019 4102 NDT Notes.pdf
7/14
acoustic emission (AE) monitoring. Some bridges are being fitted with AE instruments that listen to the
sounds that a bridge makes. These sophisticated systems can detect the sound energy produced when a
crack grows and alert the inspector to the cracks presence. Sensors can be permanently fixed to the
bridge and the data transmitted back to the lab so that continuous bridge condition monitoring ispossible. The image provided here shows field engineers installing an AE monitoring system on the lift
cables of the Ben Franklin Bridge in Philadelphia, PA
8/10/2019 4102 NDT Notes.pdf
8/14
Pipeline Inspection
In the United States, millions of miles of pipeline carrying everythingfrom water to crude oil. The pipe is vulnerable to attack by internal
and external corrosion, cracking, third party damage and
manufacturing flaws. If a pipeline carrying water springs a leak
bursts, it can be a problem but it usually doesn't harm theenvironment. However, if a petroleum or chemical pipeline leaks, it
can be a environmental disaster. More information on recent USpipeline accidents can be found at the,National Transportation
Safety Board's Internet site. In an attempt to keep pipelines operating
safely, periodic inspections are performed to find flaws and damage before they become cause for
concern.
When a pipeline is built, inspection personnel may use visual, X-
ray, magnetic particle, ultrasonic and other inspection methods to
evaluate the welds and ensure that they are of high quality. Theimage to the left show two NDT technicians setting up equipment
to perform an X-ray inspection of a pipe weld. These inspections
are performed as the pipeline is being constructed so gaining accessthe inspection area is not problem. In some areas like Alaska,
sections of pipeline are left above ground like shown above, but in
most areas they get buried. Once the pipe is buried, it is undesirable
to dig it up for any reason.
So, how do you inspect a buried pipeline?
Have you ever felt the ground move under your feet? If you're standing in New
York City, it may be the subway train passing by. However, if you're standing inthe middle of a field in Kansas it may be a pig passing under your feet. Huh???
Engineers have developed devices, called pigs, that are sent through the buried
pipe to perform inspections and clean the pipe. If you're standing near a pipeline,vibrations can be felt as these pigs move through the pipeline. The pigs are about
the same diameter of the pipe so they range in size from small to huge. The pigs
are carried through the pipe by the flow of the liquid or gas and can travel and
perform inspections over very large distances. They may be put into the pipe lineon one end and taken out at the
other. The pigs carry a small
computer to collect, store andtransmit the data for analysis.
In 1997, a pig set a world record when it completed a
continuous inspection of the Trans Alaska crude oilpipeline, covering a distance of 1,055 km in one run.
Click here to read more about this record setting
inspection.
Pigs use several nondestructive testing methods toperform the inspections. Most pigs use a magnetic flux
leakage method but some also use ultrasound to
8/10/2019 4102 NDT Notes.pdf
9/14
perform the inspections. The pig shown to the left and below uses magnetic flux leakage. A strong
magnetic field is established in the pipe wall using either magnets or by injecting electrical current into
the steel. Damaged areas of the pipe can not support as much magnetic flux as undamaged areas so
magnetic flux leaks out of the pipe wall at the damaged areas. An array of sensor around thecircumference of the pig detects the magnetic flux leakage and notes the area of damage. Pigs that use
ultrasound, have an array of transducers that emits a high frequency sound pulse perpendicular to the
pipe wall and receives echo signals from the inner surface and the outer surface of the pipe. The toolmeasures the time interval between the arrival of a reflected echos from inner surface and outer surface
to calculate the wall thickness.
On some pipelines it is easier to use remote visual inspection equipment to assess the condition of thepipe. Robotic crawlers of all shapes and sizes have been developed to navigate the pipe. The video
signal is typically fed to a truck where an operator reviews the images and controls the robot.
8/10/2019 4102 NDT Notes.pdf
10/14
Rail Inspection
One of the major problems that railroads have facedsince the earliest days is the prevention of service
failures in track. As is the case with all modes of high-
speed travel, failures of an essential component can have
serious consequences. The North American railroadshave been inspecting their most costly infrastructure
asset, the rail, since the late 1920's. With increasedtraffic at higher speed, and with heavier axle loads in the
1990's, rail inspection is more important today than it has
ever been. Although the focus of the inspection seems
like a fairly well-defined piece of steel, the testingvariables present are significant and make the inspection
process challenging.
Rail is manufactured in different weights; there aredifferent rail conditions (wear, corrosion etc) present;
there are a significant number of potential defects
possible; and the task has to be performed with somespeed to reliably inspect the thousands of miles of track
stretching across the land. Sperry Rail Service, one of the
country's leading inspector of railroad tracks, has been
using specialized test equipment mounted on self-propelled rail cars for over seventy years to protect the
safety of passengers and freight. This information
provides a brief look at rail inspection.
The history of railroading is rooted in the production of
the first metal rails near the city of Sheffield, England in 1776. The rail improved the transportation of
materials in industries such as mining. In 1803 the first railroad intended for public use was opened foroperation between the London docks and Croyden. This first railway, the Surrey Iron Railway, offered a
smoother ride than a wagon, but offered no real advantage in speed since draft animals were used for
locomotion. However, the first steam locomotive was soon to arrive on the scene. In 1804, a steam
locomotive pulled a train of cars carrying several tons of ore for the iron works at Merthyr Tydfil inSouth Wales. The first American locomotive, the Best Friend of Charleston, was placed in operation on
the South Carolina Railroad in 1831.
8/10/2019 4102 NDT Notes.pdf
11/14
The rails have evolved from cast iron plates to specially alloyed steels, which are rolled to a standardshape and specially heat-treated to obtain the desired properties. The figures above show the progression
of rail development. Present day steel rails are vastly superior to their predecessors in both strength and
wear qualities, however defects still develop. The heavy loads and high speed of today's trains can causerails to fail in service unless regular inspections are performed.
Rail inspections were initially performed solely by visual means. Of course,
visual inspections will only detect external defects and sometimes the subtle
signs of large internal problems. The need for a better inspection method
became a high priority because of a derailment at Manchester, NY in 1911, inwhich 29 people were killed and 60 seriously injured. In the U.S. Bureau of
Safety's (now the National Transportation Safety Board) investigation of theaccident, a broken rail was determined to be the cause of the derailment. The
bureau established that the rail failure was caused by a defect that was entirely
internal and probably could not have been detected by visual means. Thedefect was called a transverse fissure (example shown on the left). The railroads began investigating the
prevalence of this defect and found transverse fissures were widespread.
In 1915, the Bureau of Standards began research to determine if magnetic testing could be used to detect
transverse fissures. The inspection technique involved passing a magnetizing solenoid along the rail to
establish a flux in the rail. Flux leakage caused by a defect was detected with search coils. The techniquewas successful in the laboratory but was unable to differentiate between defects and non-relevant rail
features in the field.
8/10/2019 4102 NDT Notes.pdf
12/14
In 1923, Dr. Elmer Sperry, started to develop and build a
rail inspection car with the capability of detecting
transverse fissures in railroad rails. In 1927 Sperry built an
inspection car (shown on the right) under contract with theAmerican Railway Association. The small flatbed in front
of the cab contained the inspection equipment. The
operator and recording devices were housed in the cab.
In 1928, a Sperry built inspection car, SRS 102, was testing
rail on the Wabash Railway in Montpelier, Ohio. The
inspection technique Sperry used established a strongmagnetic field in the rail by passing a large amount of low voltage current through it. A pair of search
coils, fixed at a constant distance from the rail, detected any changes in the magnetic field around the
rail. This magnetic induction flux leakage technique became the foundation of early rail inspection.
This drawing on the left shows the basic operation ofrail inspection using the induction method. Brushes are
used to contact the rail and "inject" electrical current.
The current creates a strong magnetic field in the rail.Where there is a defect in the rail, the steel material
will not support magnetic flux and some of the flux is
forced out of the part. The sensing coil detects a changein the magnetic field and the defect indication is
recorded on the strip chart. Computers are now being
used to record and evaluate the date.
Unfortunately, transverse fissures are not the only types
of defects found in rail. Other manufacturing and service-related defects that can occur includeinclusions, seams, shelling, and corrosion. Fatigue cracks can initiate from these defects, as well as
normal features of the rail such as bolt-holes. If these defects go undetected, they can lead to rail headand web separations. Many of these defects are not detectable with the flux leakage method because the
flaws run parallel to the magnet flux lines or the flaws are too far away from the sensing coils to detect.
The induction technique inspects mainly the railhead.
To complement the flux leakage method, and detect additional flaw types, ultrasonic inspection has
become common. High-frequency sound is transmitted into the metal rail and reflections from rail jointsand surface conditions, as well as internal defects, are displayed on a screen or cause movement of a pen
on a recording tape. Both normal- and angle-beam techniques are used, as are both pulse-echo and pitch-
catch techniques. The different transducer arrangements offer different inspection capabilities. Manualcontact testing is done to evaluate small sections of rail but the ultrasonic inspection has been automated
to allow inspection of large amounts of rail, like the electromagnetic technique previously discussed.The first all-ultrasonic inspection car was introduced in 1959. This car was developed specifically to
meet the needs of the New York City Transit Authority (NYCTA).
Fluid filled wheels or sleds are often used to couple the transducers to the rail. Sperry Rail Services has,
over the years, developed and made use of Roller Search Units (RSU's) comprising a combination of
different transducer angles to achieve the best inspection possible. A schematic of an RSU is shownbelow.
8/10/2019 4102 NDT Notes.pdf
13/14
At Sperry, there are two primary inspection units. The SperryRail Detector Car, referred to as the "big" car, uses both
ultrasonic and electromagnetic technologies to identify defects.
The inspection equipment on a Sperry test car is carried in a
carriage slung between the axles.
The Hi-Rail trucks
currently use only
ultrasonics becausethe electromagnet
equipment is too large
for this vehicle. The detector car will test rail between 6.5 and13 miles per hour. However, higher speed units are in
development.
The data from the inspection
equipment is fed to the operatorinside the car. A picture of the
operator station is shown on the right. Federal Railroad Administration (FRA)
rules require that any indication considered suspect by the test equipment onthe test car are hand verified immediately. This leads to a stop-start test mode.
When the operator sees something on the tape indicating a problem, he uses a
buzzer signal system to tell the driver up front to stop. The car then backs upto the point of examination where the operator gets out to hand test the rail
with an ultrasonic test set mounted on the rear of the car. If a defect isconfirmed, it is marked and a railroad work crew following the Sperry car will change the rail. If they
can't get to it right away, the section of track is assigned a slow order (slower speed) until the crew canrepair it. The amount of rail being tested can be increased by the use of chase cars following the testing
vehicles. The chase cars will receive a radioed signal of the test being done by the lead truck and will
stop to do the necessary hand testing. This elimination of the need to back up to hand test, allows thetesting vehicle to move forward, continuously testing, with the results being sent and recorded for
examination by the chase car.
8/10/2019 4102 NDT Notes.pdf
14/14
Wire Rope (Cable) Inspection
Most skiers and snowboarders rate ski resorts by their average powder base and theoverall quality of the slopes. Few likely give serious consideration to the safety of
chair lifts at their favorite mountains. It is likely, however, that many have looked
up at that relatively small cable that they are dangling from high in the air and
hoped that someone had check to see that it was in good working condition.Luckily, ski resort operators and governing authorities perform regular inspections
and maintenance of chair lifts to ensure passenger safety . One of the components
that gets close scrutiny is the cable.
Wire rope or cable is made by weaving many
individual wires together to produce a product that is both strong andflexible. Wire rope is used in many safety critical applications in
addition to chair lift and gondola systems. Some of these applications
include hoisting systems, such as cranes and winches; guy wires used intall antennas and towers; and mooring lines of oil drilling platforms at
sea. A cable failure in one of these applications could have very serious
consequences.
All wire rope eventually wears out making periodic inspections necessarythroughout the service life of the rope. Wire rope is prone to damage and wear due
to abrasion, fatigue, corrosion, and improper handling. NDT personnel look for
localized flaws or loss of metallic cross-sectional area using a variety of inspectionmethods. The least sophisticated method is visual inspection. Inspector simply look
for broken strands, wear and corrosion on the surface of the cable. However, for a
more thorough evaluation, a number of instruments have been developed that allow
inspectors to assess the internal areas of the cable.
One of the more widely used of
these instruments uses magnetism
to inspect the rope. The inspectioninstrument is placed around the
wire rope and moved along the rope or the rope is
pulled through the instrument. Strong permanentmagnets or electromagnets are used to create a strong
magnetic field within the rope. The rope is said to be
magnetically saturated because it is caring all the
magnet flux that it possibly can. In areas where the ropeis damaged, it can not support as much of the magnet
flux and some of it "leaks" out of the rope. Sensors in
the inspection head detect the magnetic flux leakagecaused by the internal or external defects in the rope.
Defects as small as 0.05 % of the rope's cross-sectional area can often be detected.