8/12/2019 01 Introduction to Recip Engine (Ignition)
1/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
RECIP. ENGINE OVERHAUL
http://localhost/var/www/apps/conversion/tmp/scratch_9/Recip%20engine1.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Recip%20engine1.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
2/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
TYPES OF ENGINE1. INTERNAL COMBUSTION ENGINE
- combustionoccurs inside the engines (cylinders)
e.g; piston engine, turbineengine, rotary engine and
stirling engine
2. EXTERNAL COMBUSTION ENGINE.
- combustion occurs outside the engine
e.g: old locomotivesand ships to run the propeller.
http://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20STROKE%205%20events.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TURBINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROTARY%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/STIRLING%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LOCOMOTIVE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LOCOMOTIVE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/STIRLING%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROTARY%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TURBINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20STROKE%205%20events.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
3/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
GENERAL DESIGN AND CONSTRUCTION
Internal combustion engine or heat engine, convert heat
energy to mechanical energy to drive a propeller from theexpansion of gas (as result of combustion of fuel and air).
Reciprocating engines derive their name from the back-and-forth, or reciprocating movement of their pistons.
http://localhost/var/www/apps/conversion/tmp/scratch_9/RECIP%20ENGINE%20BASIC%20PART.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RECIP%20ENGINE%20BASIC%20PART.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
4/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
TYPE OF RECIPROCATING ENGINE
1. CLASSIFICATION
a. Cylinder arrangement with respect to the crankshaft
b. Method of cooling (liquid cooled or air cooled)
a. Cylinder arrangement
1. Radial engines.
2. In-line engines.
3. V-type engines.
4. Opposed type engines.
8/12/2019 01 Introduction to Recip Engine (Ignition)
5/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
1. RADIAL ENGINE.
a. Rotary type
b. Static type
1a. Rotarytype radial engine- Cylinder mounted around the crankcase
- Cylinder and propeller rotate together and crankshaft
stationary.
- Most popular rotating engine was the Bently,
GnomeandLeRhone
http://localhost/var/www/apps/conversion/tmp/scratch_9/ROTARY%20TYPE%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Gnome%20engine.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LeRhone%20Engine.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LeRhone%20Engine.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LeRhone%20Engine.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Gnome%20engine.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROTARY%20TYPE%20RADIAL%20ENGINE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
6/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
1a. Disadvantage of the rotary radial engine
- The torqueeffect produced by the large rotating mass of
the propeller and cylinders made aircraft difficult to control.- Coupled with carburetor, lubrication and exhaust
problem.
- Large frontal area
- Have some cooling problem
http://localhost/var/www/apps/conversion/tmp/scratch_9/1918%20Gnome%20rotary%20engine%20running.mp4http://localhost/var/www/apps/conversion/tmp/scratch_9/1918%20Gnome%20rotary%20engine%20running.mp48/12/2019 01 Introduction to Recip Engine (Ignition)
7/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
1b. Static type radial engine.
- Engine is stationary and bolted to the airframe.
- Crankshaft rotates and turns the propeller.
- No. of cylinders from 3 to 28 cylinders.
- Consist of a singlerow and multiplerows, max of 4rows with 7 cylinders in a row. And total of 28 cylinders.
- Produce higher horsepower and high power to weight
ratio, mostly used on military and civilian transport
aircraft.
- Most radial engine is a single row and has an odd numberof the cylinder and connected to the single crankshaft.
- In multiple row radial engine, cylinder is staggeredbehind
the space between the frontal cylinders to increase the
amount airflow past each cylinder for cooling
http://localhost/var/www/apps/conversion/tmp/scratch_9/RADIAL%20ENGINE2.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SINGLE-ROW%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/DOUBLE-ROW%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/staggered%20cylinder.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/staggered%20cylinder.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/DOUBLE-ROW%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SINGLE-ROW%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RADIAL%20ENGINE2.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
8/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
2. IN-LINE ENGINE
- Cylinder are aligned in single row parallel with crankshaft.- engine either liquid or air-cooled
- Piston either located upright or inverted.
- Invertedengine is generally employed.
- Number of cylinders limited to six only to facilitate cooling and
prevent engine overheating- Cylinder are generally even number to provide proper balance.
Advantages of in-line engine
- Small frontal area, less drag, greater propeller clearance as forinverted engine.
- Shorter main landing gear and provide better visibility
Disadvantages of in-line engine
- Relatively low power to weight ratio, the rearmost cylinderreceives less cooling air
- Low and medium horsepower output to engine fitted to light
aircraft only.
http://localhost/var/www/apps/conversion/tmp/scratch_9/IN-LINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/INVERTED%20INLINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/INVERTED%20INLINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/IN-LINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/IN-LINE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/IN-LINE%20ENGINE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
9/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
3. V-TYPE ENGINE
- Two type : a. Inverted V-type engine
b. Upright V-type engine.
- Cylinders are arranged in two rows (bank) forming letter V
- Angle between banks 45, 60 or 90 deg.
- Cylinders are always even number in each row
- The two banks are opposite each other
- Most V-type engine has 8 or 12 cylinders
- Either air cooled or liquid cooled
- Still employed typically found on racing aircraft.
Advantages of V-type engine
- Producing higher horsepower than in-line engine
- Small frontal area with higher power to weight ratio
- Better pilot visibility as shorter/lower main landing gear.
http://localhost/var/www/apps/conversion/tmp/scratch_9/V-TYPE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/V-TYPE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/V-TYPE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/V-TYPE%20ENGINE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
10/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
iv. OPPOSED TYPE ENGINE
- Most popular recip. engine used on light aircraft.
- Engine as little as 36 hp. and as much as 400 hp.
- Cylinder are always even numbers and opposes each other.
- Some engines are liquidcooled, mostly air cooled
- Horizontally installed on fixed wing aircraft.- When installed on helicopter it is mounted vertically.
- Recent development engine employs dual electronic ignitionsystem.
Advantages
- High power to weight ratio because of small and light weightcrankcase.
- Small frontal areas, more streamline and less drag
- Less vibration because the power impulses tend to canceleach other.
http://localhost/var/www/apps/conversion/tmp/scratch_9/OPPOSED%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LIQUID-COOLED.ppthttp://localhost/var/www/apps/conversion/02%20RECIPROCATING%20ENGINE%20DIAGRAM1/Boxerengineanimation.gifhttp://localhost/var/www/apps/conversion/02%20RECIPROCATING%20ENGINE%20DIAGRAM1/engine-flat-4.gifhttp://localhost/var/www/apps/conversion/02%20RECIPROCATING%20ENGINE%20DIAGRAM1/engine-flat-4.gifhttp://localhost/var/www/apps/conversion/02%20RECIPROCATING%20ENGINE%20DIAGRAM1/Boxerengineanimation.gifhttp://localhost/var/www/apps/conversion/tmp/scratch_9/LIQUID-COOLED.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/OPPOSED%20ENGINE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
11/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
MAJOR ENGINE COMPONENTS1. Basic part of reciprocating engine include:
a. Crankcase
b. Crankshaft
c. Connecting rod
d. Piston
e. Cylinders
f. Valves
g. Valve operating mechanism
2. Valves, pistons and plugs are located in the cylinder
http://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20COMPONENTS.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RECIP%20ENGINE%20BASIC%20PART.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RECIP%20ENGINE%20BASIC%20PART.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20COMPONENTS.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
12/84
8/12/2019 01 Introduction to Recip Engine (Ignition)
13/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
Opposed Engine Crankcase
- Consist of two halves of cast aluminum alloy.
- Halves split vertically, held together by bolts and nuts
- Manufactured either by sand casting or mold (permold).
- Thinner wall, strong, denser (mold) and fewer tendencies
to crack due to fatigue.- Cylindrical in shape with smooth are machined to serve as
cylinder pad
- Cylinder padplace to mount cylinder to crankcase.
- To allow a crankcase to support a crankshaft, a series oftransverse webs are cast directly into a crankcase.
- Webs integral parts of the structure and houses thatbearings support the crankshaft and strengthen thecrankcase.
http://localhost/var/www/apps/conversion/tmp/scratch_9/continental%20engine.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/OPPOSED%20CRANKCASE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/OPPOSED%20CRANKCASE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/OPPOSED%20CRANKCASE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/continental%20engine.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
14/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
RadialEngine Crankcase
- Radial engine crankcase separates into 4 section
a. Nose section
b. Power section
c. Supercharger
d. Accessories section
a. Nose section
- Front of the crankcase, bolted to the power section
- Made of aluminum alloy, one piece with domed/convex shape.
- Houses and support prop. governor drive shaft,prop. shaft, cam
ring and reduction gear.
- Additionalmounting for magneto and others engine accessories.
http://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20SECTION%20OF%20RADIAL%20ENGINE%20CRANKCASE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RADIAL%20ENGINE3.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RADIAL%20ENGINE3.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20SECTION%20OF%20RADIAL%20ENGINE%20CRANKCASE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
15/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
b. Power section
- Section of the crankcase where the reciprocating motion of thepiston is converted to the rotary motion of the crankshaft.
- One or three pieces, made of aluminum or magnesium boltedtogether.
- Contain machined bosses that rigidly support the crankshaft bearingand the crankshaft.
- Cylinder are attached around the perimeter
- Inner circumference of a cylinder pad is chamfered or tapered topermit the installation of O-ring on the cylinder skirt that seal the joint
between the cylinder and cylinder pad
http://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20SECTION%20OF%20RADIAL%20ENGINE%20CRANKCASE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20SECTION%20OF%20RADIAL%20ENGINE%20CRANKCASE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
16/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
c. Diffuseror Supercharger section
- Houses the gear train, bevel and spur gear to drivevarious engine components.
- Spur gear drive heavy load on accessories.
d. Accessories section
- Provide mounting for accessories such as magneto,
carb., pump, starter and generator.
http://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20SECTION%20OF%20RADIAL%20ENGINE%20CRANKCASE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/BASIC%20SECTION%20OF%20RADIAL%20ENGINE%20CRANKCASE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
17/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
b. CRANKSHAFT
- Purpose to transform the reciprocating motion ofthe piston and connecting rod into rotary motion to
turn the propeller.- The crankshaft may have one or more throws. Twocrank cheek and crankpin is one throw
- Can withstand high stress, made of forged alloy
such as chromium-nikel molybdenum steel.
8/12/2019 01 Introduction to Recip Engine (Ignition)
18/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
b. CRANKSHAFT cond
- Main part of crankshaft
a. Main bearing journal (Main journal)
- Represent centerline of a crankshaft and supportthe crankshaft as it rotates in the main bearings
b. Crankpin
- Attachment points for the connecting rod.
- Forged directly into a crankshaft and offset fromthe main bearing journal.
c. Crank cheeks or crank arms
- Connect the crankpin to the crankshaft
d. Counterweightand dampershelp to balance theshaft dynamically
http://localhost/var/www/apps/conversion/tmp/scratch_9/CRANKSHAFT%20CONSTRUCTION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COUNTERWEIGHT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COUNTERWEIGHT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CRANKSHAFT%20CONSTRUCTION.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
19/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
b. CRANKSHAFT cond
- Types of crankshaft depend on number and arrangement ofcylinder
- The common typessingle, two, four and six throws
- Single throw crankshaft is used on single row radial engine.
Bearing
- To support and reduce friction between moving part:
a. Plain bearing - radial load onlyb. Ball bearing - high radial load
c. Roller bearing - radial load
d. Tapped - radial and thrust load.
http://localhost/var/www/apps/conversion/tmp/scratch_9/SINGLE%20THROW.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PLAIN%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/BALL%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROLLER%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TAPERED%20ROLLER%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TAPERED%20ROLLER%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TAPERED%20ROLLER%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROLLER%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/BALL%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PLAIN%20BEARING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SINGLE%20THROW.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
20/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
CRANKSHAFT BALANCE
TO REDUCE ENGINE VIBRATION WHICH CAN CAUSE FATIQUE AND
FAIL AND WEAR EXCESSIVELY
EXCESSSIVE VIBRATION IS CAUSE BY UNBALANCE CRANKSHAFT
TYPE OF BALANCE
1. STATICALLY BALANCE
2. DYNAMIC BALANCE
8/12/2019 01 Introduction to Recip Engine (Ignition)
21/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
DYNAMIC BALANCE
BALANCING THE CENTRIFUGAL FORCE CREATE BY THE ROTATINGCRANKSHAFT AND THE IMPACT FORCE CREATE BY ENGINE POWER
IMPULSE
CORRECTED THROUGH USING OF DYNAMIC DAMPERS
STATICALLY BALANCE
WHEN ENTIRE CRANKSHAFT IS BALANCE AROUND ITS AXIS OF ROTATION
CAN BE ACHIEVED BY PLACING IT IN KNIFE EDGE BALANCING BLOCK
http://localhost/var/www/apps/conversion/tmp/scratch_9/STATICALLY%20BALANCING%20FOR%20CRANKSHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/STATICALLY%20BALANCING%20FOR%20CRANKSHAFT.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
22/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
c. CONNECTING ROD
- Purpose a. To transmit exerted forces on a piston to a
crankshaft.
b. To convert reciprocating motion of piston to a
rotary motion of crankshaft.
- Small end is connected to the piston and big end
connected to the crankshaft.
- Types
a. Plain types
b. Master and articulated type
c. Fork and blade type
http://localhost/var/www/apps/conversion/tmp/scratch_9/PLAIN%20CONNECTING%20ROD.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CONNECTING%20ROD%20FOR%20RADIAL%20ENGINE%20AND%20MOVEMENT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FORK%20AND%20BLADE%20TYPE%20CONNECTING%20ROD.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FORK%20AND%20BLADE%20TYPE%20CONNECTING%20ROD.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CONNECTING%20ROD%20FOR%20RADIAL%20ENGINE%20AND%20MOVEMENT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PLAIN%20CONNECTING%20ROD.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
23/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
a. PLAINCONNECTING ROD
USED ON INLINE AND OPPOSED ENGINE
BRONZE BUSHING ARE PRESSED AT THE PISTON PIN END
CRANNKPIN END USUALLY FITTED WITH TWO PIECESBEARING AND CAP WHICH IS HELD BY BOLT AND STUD
TO PROVIDE PROPER FIT AND BALANCE CONNECTING RODARE MATCH WITH THE PISTON
STAMP WITH NUMBERS TO IDENTIFY CYLINDER AND PISTON
ASSEMBLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/PLAIN%20CONNECTING%20ROD.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PLAIN%20CONNECTING%20ROD.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
24/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
b. MASTERAND ARTICULATED ROD
USED ON RADIAL TYPE OF PISTON ENGINE
ONE PISTON IN EACH ROW OF CYLINDER IS CONNECTED TOCRANKSHAFT BY A MASTER ROD
THE REMAINING PISTON IS CONNECTED TO A MASTER ROD THROUGH A
LINK OR ARTICULATED RODSMASTER ROD ARE MANUFACTURED FROM A STEEL ALLOY FORGINGWHILE LINK ARE MANUFACTURED FROM FORGED STEEL ALLOW
LINK ROD IS EITHER I OR H CROSS SECTIONAL PROFILE
MASTER ROD IS THE ONLY BETWEEN THE PISTON AND THE CRANKPIN
LINK ROD IS ATTACHED TO MASTER THROUGH KNUCKLE PIN
SOME KNUCKLE PIN DO NOT IN THE FLANGE HOLE BUT SOME FULLFLOATING
http://localhost/var/www/apps/conversion/tmp/scratch_9/CONNECTING%20ROD%20FOR%20RADIAL%20ENGINE%20AND%20MOVEMENT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CONNECTING%20ROD%20FOR%20RADIAL%20ENGINE%20AND%20MOVEMENT.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
25/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
FORK AND BLADE TYPE
- Used primarily on V-type engine.- Consists of fork-connecting rod and blade
connecting rod
http://localhost/var/www/apps/conversion/tmp/scratch_9/FORK%20AND%20BLADE%20TYPE%20CONNECTING%20ROD.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FORK%20AND%20BLADE%20TYPE%20CONNECTING%20ROD.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
26/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
d. PISTON
- Two primary functions:
a. Draw fuel and air into a cylinder and compress the gases
b. To transmit the force produced by combustion to thecrankshaft
- The ring grooves are cut at outside surface of piston to hold set of pistonrings. As many as six ring grooves.
- The lower/base of the piston are called piston skirt.- Piston are often classified according to their head design.
- Type of heads:
a. Flat head
b. Flat head with valve recessed
c. Cupped head
d. Domed head
e. Truncated cone
- Flat head type is commonly used in modern aircraft
- All piston expend as they heat up. Camground piston compensate foruneven expansion of the piston.
http://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20CONSTRUCTION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20AND%20OIL%20RING%20ARE%20INSTALLATION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20CONSTRUCTION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20HEAD%20SHAPE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CAM%20GROUND%20PISTON.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CAM%20GROUND%20PISTON.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20HEAD%20SHAPE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20CONSTRUCTION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20AND%20OIL%20RING%20ARE%20INSTALLATION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20AND%20OIL%20RING%20ARE%20INSTALLATION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20CONSTRUCTION.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
27/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
d. PISTON cont
Piston rings- Perform three functions
a. To prevent gas leakage from combustion chamber
b. Reduce oil leakage into combustion chamber.
c. To transfer heat from the piston to cylinder wall
- Piston ring gap
a. Butt joint
b. Angle joint
c. Step joint
- Types of piston ring
a. Compression ring
prevent gas escape past the piston during engineoperation.
- placed in the ring groove below the piston head.
- no. of ring used on piston determined by the type ofengine and design.
http://localhost/var/www/apps/conversion/tmp/scratch_9/RECIP%20ENGINE%20BASIC%20PART.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TYPES%20OF%20PISTON%20RING%20GAP.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/POSITION%20OF%20COM.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/POSITION%20OF%20COM.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TYPES%20OF%20PISTON%20RING%20GAP.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/RECIP%20ENGINE%20BASIC%20PART.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
28/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
d. PISTON cont
b. Oil ring
control amount of oil that applied to the cylinder wall as well asprevent oil from entering the combustion chamber.
- 2 types of oil ring
1. Oil control ring- to regulate the thickness of oil film on the cyl. wall.
- placed below compression ring
2. Oil scraper ring (oil wiper ring)
- to regulate amount of oil that passes between thepiston skirt and cylinder wall.
- usually beveled face and installed belowof thepiston skirt.
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/POSITION%20OF%20COM.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/POSITION%20OF%20COM.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
29/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
d. PISTON cont
- Ring gap must be staggered/offset to prevent gas leak or known as blow-by
ring gaps are staggered at 120 apart for three piston rings.
- Cross section of piston ring
a. Rectangular
b. Taperedc. Wedge
Piston pin
Is to joint the piston to the connecting rod.
- Types of piston pina. Stationary (rigid) pinheld tightly in place by screw that
prevents movement.
b. Semi-floatingretained stationary in the connecting rod.
c. Full-floatingfree to rotate.
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/CROSS-SECTION%20OF%20PISTON%20RING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/STATIONARY%20OR%20RIGID%20PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/STATIONARY%20OR%20RIGID%20PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PISTON%20PIN.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CROSS-SECTION%20OF%20PISTON%20RING.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
30/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
d. PISTON cont
A piston pin must be held in place laterally to prevent it from rubbingand scoring the cylinder walls.
Three devices that are used to hold a piston pin in place are
1. circlets,
2. spring rings, and
3. metal plugs.
A circlet is similar to a snap ring that fits into a groove cut into each endof the piston boss.
A spring ring also fits into grooves cut into the ends of a piston boss butconsists of a single circular spring-steel coil. Both circlets and spring ringsare used primarily on earlier piston engines.
More current practice is to install a plug of relatively soft aluminumcalled a piston-pin plug.
These plugs are inserted into the open ends of the piston pins andprovide a good bearing surface against the cylinder walls.
FOR TRAINING PURPOSE ONLY
8/12/2019 01 Introduction to Recip Engine (Ignition)
31/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
e. CYLINDER- Provide a combustion chamber where the burning and expansion of
gases takes place to produce power.
- Houses of piston and connecting rod assembly as well as the valves
and spark plugs.
- Cylinder must be strong, lightweight and good heat-conductingproperties.
- Air cooled cyl. consist of : i. Barrel
ii. Cylinder heads
iii. Mounting flange
iv. Skirtv. Cooling fins
vi. Valve assembly.
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/ENGINE%20CYLINDER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ENGINE%20CYLINDER.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
32/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
e. CYLINDER cond
Cylinder barrels- Construction for cylinder barrel must be as light as possible.
- Material usedchromium molybdenum steel
- nickel chromium molybdenum steel
- Cylinder barrels are machined with a skirt that project into the
crankcase and mounting flange, used to attach the cylinder to thecrankcase.
- Exterior cylinder barrel consist of several thin cooling fins.
- Threaded at the top part of the barrel so cylinder head can be
screwed into it.
- Cylinder borechoke bore cylinder- smaller at the top for
expansions cause by operating temperature.
- The amount of choke is between .003 and .005 inches.
- Internal surface of the barrel is treated with chrome
plating/electroplating and nitriding to form of case hardening on the
surface.
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/CYLINDER%20BARREL.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CHOKE%20BORE%20CYLINDER,%20THE%20DIAMETER%20AT%20THE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CHOKE%20BORE%20CYLINDER,%20THE%20DIAMETER%20AT%20THE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CYLINDER%20BARREL.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
33/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
e. CYLINDER cond
- Identification for nitrided cylinder by applying blue band around cyl.base or cooling fin, and orange paint for the electroplating cylinders.
- chromium is too smooth that it could not retain enough oil to lubricatethe piston ring
- overcome through process called chromechanneling- chrome channeling is a process where by a reverse current is through acylinder for controlled period of time after chromium is applied
- microscopic crack will occur on the surface that help holding lubricatingoil
- Advantages over nitrided cylinder
1- less susceptible to rust and corrosion
2- once it wear beyond its usable limit it may be chromeplated back to original size
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/CHROME%20CHANNELING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CHROME%20CHANNELING.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
34/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
Cylinder headscond
- Provide an enclosed chamber for combustion
- Heads contain intake and exhaust ports, spark plug,valve actuating mechanism and also conduct heat awayfrom cylinder barrels.
- Made of forged or die-cast aluminum alloy because ofgood heat conductor, lightweight and durable
- Inner surface maybe flat, semi-spherical or peaked.
- The semi-spherical type proved to be the mostsatisfactory and stronger and provide more rapid and
thorough scavenging of exhaust gas.
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/CYLINDER%20HEAD.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CYLINDER%20HEAD.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
35/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
e. CYLINDER cond
Cylinder Numbering
- Left or right of an engine always viewing form the rear.
- The crankshaft rotation is also referenced from the rear of the
engine is specified as either clockwise or counterclockwise.
- All cylinders are numbered, odd numbered are on the right and
even numbered on the left.
- Continental engine start its cylinder numbering with the most
rearward cylinder.
- Lycomingengine start with the most forward
- Radialengine cylinders are numbered consecutively starting fromthe top cylinder and progressing clockwise as viewed from the rear of
the engine.
- Double row radial engine, all odd numbered cylinders are in the
rear row and the even numbered cylinders are in the front row
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/CONTINENTAL%20CYLINDER%20NUMBERING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LYCOMING%20CYLINDER%20NUMBERING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/DOUBLE-ROW%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/DOUBLE-ROW%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LYCOMING%20CYLINDER%20NUMBERING.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CONTINENTAL%20CYLINDER%20NUMBERING.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
36/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
f. VALVES
1. Purpose is to regulate flow of gases into and out of cylinder byopening and closing valves port at predetermine times.
2. Types of valve:
i. Intake valve (chromium, nickel or tungsten steel)
ii. Exhaust valveexhaust valve stems are hollowed and
partially filled with metallic sodium. (inconel, silicon- chromium or cobalt-chromium alloys)
3. Classified by shape of head
i. Flat head
ii. Semi tulip
iii. Tulipiv. Mushroom
4. Valve springs are hold valve face against valve seat
5. Valve springs are held in place by spring retainer and split key
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/VALVE%20ASSEMBLY.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TYPE%20OF%20VALVE%20FACE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/VALVE%20IN%20POSITION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SPLIT%20KEY.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SPLIT%20KEY.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/VALVE%20IN%20POSITION.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TYPE%20OF%20VALVE%20FACE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/VALVE%20ASSEMBLY.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
37/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
g. VALVE OPERATING MECHANISM
- To open and close each valve at correct time
- Consist of :
i. Camshaft or cam rings
ii. Valve lifter or tapped
iii. Pushrod
iv. Rocker arm
- Camshaft is used in opposed engine while cam ring is used in radial
engine
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/VALVE%20OPERATING%20MECHANISM1.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CAMSHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/HYDRAULIC%20LIFTER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PUSH%20ROD%20N%20COVER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROCKER%20ARM.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROCKER%20ARM.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PUSH%20ROD%20N%20COVER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/HYDRAULIC%20LIFTER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CAMSHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/VALVE%20OPERATING%20MECHANISM1.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
38/84
Malaysian Institute of Aviation Technology
HYDRAULICLIFTERS
1. MOST OPPOSED ENGINE USED HYDRAULIC LIFTERS2. USED OIL PRESSURE TO CUSHION THE IMPACT OF THE
CAMLOBES STRIKING THE LIFTER AND REMOVES ANY PLAY
WITHIN THE VALVES OPERATING MECHENISM
FOR TRAINING PURPOSE ONLY
http://localhost/var/www/apps/conversion/tmp/scratch_9/HYDRAULIC%20LIFTER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/HYDRAULIC%20LIFTER.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
39/84
Malaysian Institute of Aviation Technology
OPPOSED ENGINE VALVE OPERATING
MECHANISM
1. Valve operation begins with the camshaft
2. Consists of round shaft with a series of cams or lobes.
3. To transform a circular motion of the crankshaft to a linear motionneeded to actuate valve.
4. The shape of the cam lobes determines valve left (distance a valvelifted off its seat and valve duration)
5. Each valve must open and close for every two rotations of thecrankshaft. (speed of camshaft is one-half that of the crankshaft.
6. OPERATION: camshaft rotates, the lobe raise the valve lifter (tappet),transmits the lifting force of the cam to the push rod
FOR TRAINING PURPOSE ONLY
i i f A i i
http://localhost/var/www/apps/conversion/tmp/scratch_9/CAMSHAFT%201.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/4-STROKE%20CYCLES%20OF%20RECIP%20ENGIE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/4-STROKE%20CYCLES%20OF%20RECIP%20ENGIE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/CAMSHAFT%201.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
40/84
Malaysian Institute of Aviation Technology
PUSH ROD
Transmit lifter action to the rocker arm
Hole on each end to allow oil flow from lifter to valve
component
Enclose by thin metal shroud that run from cylinder head to
crankcase
These provide return path for oil that is pump up to cylinder
head
FOR TRAINING PURPOSE ONLY
M l i I tit t f A i ti T h l
http://localhost/var/www/apps/conversion/tmp/scratch_9/PUSH%20ROD%20N%20COVER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/PUSH%20ROD%20N%20COVER.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
41/84
Malaysian Institute of Aviation Technology
ROCKER ARM
PURPOSE
Change lifting movement of the pushrod
into downward motion needed to open
the valve
FOR TRAINING PURPOSE ONLY
M l i I tit t f A i ti T h l
http://localhost/var/www/apps/conversion/tmp/scratch_9/ROCKER%20ARM.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/ROCKER%20ARM.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
42/84
Malaysian Institute of Aviation Technology
RADIALENGINE VALVE OPERATING
MECHANISM1. VALVE OPERATING MECHANISM ON RADIAL USED ONE OR TWO
DEPENDING ON THE NO. OF ROWS
2. THE CAMRING IS A CIRCULAR PIECE OF STEEL WITH A SERIES OF CAM
LOBES.3. THE SMOOTH AREA BETWEEN THE LOBES IS CALLED CAM TRACK
4. CAM RING IS DRIVEN BY CRANKSHAFT THROUGH A SERIES OF GEAR.
5. THE SPEED OF THE CAMRING IS CAN BE DETERMINED BY USING THE
FORMULA
1
2 X NUMBER OF LOBES
FOR TRAINING PURPOSE ONLY
M l i I tit t f A i ti T h l
http://localhost/var/www/apps/conversion/tmp/scratch_9/HYDRAULIC%20LIFTER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/HYDRAULIC%20LIFTER.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
43/84
Malaysian Institute of Aviation Technology
VALVE CLEARANCE
SPACE OR CLEARANCE BETWEEN VALVE TIP AND ROCKER ARM FACE
VALVE CLEARANCE
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
44/84
Malaysian Institute of Aviation Technology
VALVE CLEARANCE1. To maintain engine running smoothly
2. To set up the valve clearances, refer engine MM specifieseither cold or hot valve clearance.
3. During normal engine operating temperature, the cylinderassemblies expand and force the cylinder along with itvalve operating component further away from thecrankcase.
4. Due to mass the push rod expand less than the cylinderresulting increases in valve clearance.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
45/84
Malaysian Institute of Aviation Technology
PROPELLER REDUCTION GEAR
- Purpose of the reduction gear, permits a propeller to turn slower than
the engine speed.
- Mostly used by the high powered engine.
- Utilize spur gears, planetary gears or a combination of two.
- Whenever reduction gear is used that does not aligned with thecrankshaft, vibration will be created to the engine.
- To minimize the vibration a quill shaft and planetary reduction gear is
used
- Type of propeller shaft
1- Taperedpropeller shaft2- Splinedpropeller shaft
3- Flangedpropeller shaft
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/TAPERED%20PROPELLER%20SHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SPLINED%20PROPELLER%20SHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FLANGED%20PROPELLER%20SHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FLANGED%20PROPELLER%20SHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/SPLINED%20PROPELLER%20SHAFT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TAPERED%20PROPELLER%20SHAFT.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
46/84
Malaysian Institute of Aviation Technology
ENGINE IDENTIFICATION- Almost recip. engine are identified by a series of letters and numbers.- Most manufacturers use the same identification code consists of letter or
series of letters followed by number and model designation.
- Ohorizontally opposed engine
Rradial engine
Iinline engine
Vv-type engine
Tturbocharged
Ifuel injected
SsuperchargedGgeared nose section
LLH rotation for multi engine
Hhorizontal mounting for helicopters
Vvertical mounting for helicopter
Amodified for aerobatics
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
47/84
Malaysian Institute of Aviation Technology
ENGINE IDENTIFICATION cond
1- e.g ; O-320 indicate horizontally opposed engine with a
displacement of 320 cubic inch.
2- e.g ; LIO-360-C indicate left-hand rotation, fuel injected,horizontally opposed engine, displacement of 320 cubic inch
and C model.
3- e.g : GTSIO-520-F indicate engine is geared, turbocharged
engine, fuel injected, horizontally opposed engine, displaces520 cubic inch and F model
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
48/84
Malaysian Institute of Aviation Technology
FINISH FOR THE DESIGN AND CONSTRUCTIONOF RECIP ENGINE
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
49/84
Malaysian Institute of Aviation Technology
RECIPROCATING ENGINEOPERATING PRINCIPLES
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
50/84
Malaysian Institute of Aviation Technology
ENERGY TRANSFORMATION
- AN ENGINE IS A DEVICE THAT CONVERTCHEMICAL ENERGY OF THE FUEL INTO HEAT
ENERGY
- ONCE CONVERTED, THE HEAT CUASES AN
INCREASE OF GAS PRESSURE IN THE CYLINDERTHAT CONVERT IT INTO MECHANICAL ENERGY
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
51/84
Malaysian Institute of Aviation Technology
BASIC OPERATING PRINCIPLES cond
TERM:
1. Type of operating cycle :
a. Four stroke
b. Two strokeThose operating cycles are developed by August Otto, sometimes
referred as OTTO CYCLE.
2. Stroke is a total distance travel of piston most outward and inward.
3. Most outward travel is called top dead center (TDC)
4. Most inward travel is called bottom dead center (BDC)
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/TERM%20FOR%20RECIP.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TERM%20FOR%20RECIP.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
52/84
ys s u e o v o ec o ogy
BASIC OPERATING PRINCIPLES cond
FOUR STROKE CYCLE
1. The four stroke cycles consists of :
a. Intake stroke
b. Compression stroke
c. Power stroke
d. Exhaust stroke
2. To complete four stroke cycle requires two revolutionsof the crankshaft.
3. Ignition takes place during compression stroke.Therefore in one complete cycle there are four strokeand five events.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
53/84
y gy
OPERATING PRINCIPLES
1. The sequences of events of reciprocating engine are :
i. Intake
ii. Compression
iii. Ignition
iv. Power
v. Exhaust
i. Intake
- Piston travels from top dead center to bottom dead center.
- Intake valve opens and exhaust valve closes.
- Fuel and air mixture drawn into cylinder
ii. Compression
- Piston travels from top dead center to bottom dead center.
- Both valves are closed
- Mixture fuel and air compressed
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/Intake.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20STROKE%205%20events.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/COMPRESSION%20STROKE%205%20events.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Intake.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
54/84
y gy
iii.. Ignition
- Compressed mixture is ignited by spark plug.
- Both valves are still closed
- Piston near top/top dead center
iv. Power- Expanded burning gases forces piston downward
- Crankshaft rotates to produces work.
- Both valves are still closed
v. Exhaust
- Exhaust valve opens and intake valve still close.
- Piston travels from bottom to top dead center.
- Burned gases scavenged out of cylinder.
2. All five events are considered one cycle.
BASIC OPERATING PRINCIPLES cond
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/Ignition.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Power.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Exhaust.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/4-STROKE%20CYCLES%20OF%20RECIP%20ENGIE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/4-STROKE%20CYCLES%20OF%20RECIP%20ENGIE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Exhaust.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Power.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Ignition.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
55/84
y gy
VALVE TIMING OR MODIFIED OTTOCYCLE
TERM USED TO DESCRIBES THE POINT ATWHICH THE INTAKE AND EXHAUST BEGIN
TO OPEN AND CLOSED DURING THE FOUR
STROKE CYCLE
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
56/84
VALVE TIMING- To increase engine performance and more efficient.
- The no. of crankshaft degrees that the intake valve opens early
before the piston reaches TDC (valve lead).
- To ensure sufficient charge (mixture) enter the cylinder.
- The no. of degrees the exhaust valve remain open after TDC. (valve
lag).
- To ensure fully scavenge of hot gases from the cylinder.
- Combination of the valve lead and valve lag is called VALVE
OVERLAP.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/MODIFIED%20OTTO%20CYCLE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/MODIFIED%20OTTO%20CYCLE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
57/84
- Purpose of valve overlap is to allow the charge (mixture) toenter the cylinder as early as possible to increase engine
performance and aid in cylinder cooling and also to ensurefully scavenge of hot gases from the cylinder.
- Therefore, e.g. if the amount of intake valve open, will be 15degrees to reach TBC, 180 degrees to reach BDC then 45
degrees past BC and the total of 240 degrees of rotation.(duration of intake valve open).
VALVE TIMING
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/MODIFIED%20OTTO%20CYCLE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/MODIFIED%20OTTO%20CYCLE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
58/84
FIRING ORDER
Define as
- the sequence in which ignition occurs in different
cylinder
- Each engine is designed with a specific firing order tomaintain balance and reduce vibration.
Example
- continental0-200a= 1324
- lycoming0-320-E3D = same order but cylinder arenumbered differently
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20OF%20CONTINENTAL%20ENGINE%200200A.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20OF%20LYCOMING%20ENGINE%200320E3D.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20OF%20LYCOMING%20ENGINE%200320E3D.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20OF%20CONTINENTAL%20ENGINE%200200A.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
59/84
FIRING ORDER ON RADIAL ENGINE
THE ODDCYLINDER FIRE FIRST FOLLOWED BY THE EVEN NOCYLINDER.
14 CYLINDER = +9 -5, MEANS IF NO 1 IS FIRING THE NEXTCYLINDER TO FIRE IS 1 + 9 = 10 CYLINDER, THE NEXT CLINDER TOFIRE IS 105 = 5 AND SO O N
18 CYLINDER +117, IF NO 1 CYLINDER IS FIRING THE NEXTCYLINDER TO FIRE IS 1 + 11= 12 NEXT WILL BE 127 = 5
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20FOR%20SINGLE%20ROW%209%20CYLINDER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20FOR%2018%20CYLINDERS%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20FOR%2018%20CYLINDERS%20RADIAL%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/FIRING%20ORDER%20FOR%20SINGLE%20ROW%209%20CYLINDER.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
60/84
BASIC OPERATING PRINCIPLES cond
TWO STROKE CYCLE
1. Has the same five events and only two piston strokes rather than fourstrokes in only one crankshaft revolution to complete the cycle.
2. Each stroke two events take place.
3. When piston moves up induction and compression takes place.4. Ignition occurs when piston moves up a few degrees before top dead
center.
5. When piston moves down power and exhaust occur
6. During downward movement of pistoncompression also takes place
in crankcase not in cylinder.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/TWO%20STROKE%20ENGINE.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/TWO%20STROKE%20ENGINE.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
61/84
WORK-POWER CONSIDERATIONS
ALL AIRCRAFT ENGINE ARE TESTED AND RATED ACCORDING
TO THEIR ABILITY TO DO WORK AND PRODUCE POWER.
ENGINE DESIGNS AND CONSTRUCTION DETERMINES HOW
EFFECTIVE IN CONVERTING FUELS CHEMICAL ENERGY TO
WORK AND POWER
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
62/84
DEFINATION OF WORK If force applied to an object and the object moves,
work is done.
Amount of work done is directly proportional to theforce applied and distance the object moves.
If force is applied to an object and the does notmoves , work is not done.
Work produced by the engine is used to turn the
propellerwork (w) = force (f) x distance (d)
= ______ ft/lbs
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
63/84
DEFINATION OF WORK English system, work is typically measured in foot-pounds. One foot-
pound is equal to one pound of force applied to an object through thedistance of one foot
In the metric system, the unit of work is the joule.
One joule is the work done by a force of one newton acting through adistance of one meter.
One pound is equal to 4.448 newtons.
The work produced by an engine is used to turn a propeller which isproduces thrust to move an aircraft.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
64/84
POWER
When determining the amount of work done, time required to do thework is not considered, Power, on the other hand, does take time intoconsideration.
Define as time rate of doing work.
FORMULA
FORCE X DISTANCE = ___________ft/lbs/secTIME
When rating engines, power is a primary consideration because itrepresents how quickly an engine-propeller combination can respond topower demands.
Power is a critical factor when determining whether or not an engine candeliver the force needed to produce a specific amount of work in a giventime.
E.g., a large airplane needs more power to take off in the samedistance as a small airplane because more force is needed to accelerate aheavier object the same distance in the same amount of time.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
65/84
HORSE POWER Another unit of measure for power is the horse-power.
The amount of power required to do 33,000 ft/lbs work in 1 minor 550 foot-pounds of work in one second.
HORSEPOWER = FORCE X DISTANCE
33000 X TIME
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
66/84
INDICATED HORSE POWER
(IHP) is the total power actually developed in an enginescylinders without reference to friction losses within theengine.
To calculate indicated horsepower, the average effective
pressure within the cylinders must be known. One way to determine the effective pressure is to attach a
mechanical indicating device to the engine cylinder thatrecords the actual pressure existing in the cylinder during acomplete operating cycle.
This average pressure is referred to as indicated meaneffective pressureand is included in the indicated horsepowercalculation with other engine specifications.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
67/84
INDICATED HORSE POWER
FORMULA
PLANK
33,000
P = IMEP inside the during a power strokeL = length of stroke
A = area of piston head
N = number of power stroke per min for one cylinder.
On a four-stroke engine, this is found by dividing the rpm bytwo.
K = number of cylinder
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
68/84
FRICTION HORSEPOWER
Not all of the horsepower developed by engine goes to
driving the propeller, all the moving part inside the engine
will creating friction.
Engine lubrication is crucial in limiting friction and wear, but
cannot completely eliminated.
The power required to overcome the friction and energy
losses
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
69/84
BRAKE HORSEPOWER
The actual power delivered to the propeller shaft
IHP - FHP = BHP Devices that are capable to measuring torque, including
the dynamometer and torquemeter.
Early powerplant design engineers measured brake
horsepower using a Prony brake dynamometer ,on mostmodern engines is measured with an electric or hydraulic
dynamometer.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/DYNAMOMETER.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/DYNAMOMETER.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
70/84
PISTON DISPLACEMENT
Volume of air displace by a piston as it moves from
BDC to TDC
FORMULA - A X L X N
A = area of piston head ( r )
L = length of stroke in inches
N = number cylinders
piston displacement always in cubic inches
8/12/2019 01 Introduction to Recip Engine (Ignition)
71/84
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
72/84
THERMAL EFFICIENCY
- A ratio of the amount of energy converted to useful work tothe amount of heat energy contained in the fuel used tosupport combustion
- E.g - two engine that produce the same amount hp butconsume different amount of fuel
- the engine that consume less amount of fuel has higher
thermal efficiency
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
73/84
VOLUMETERIC EFFICIENCY Ratio of volume of fuel and air takes into the cylinder to the
total piston displacement
If engine draws in volume of fuel/air that is exactly equal to
the total piston displacement, VE would be 100%
Varies with change of atmospheric condition
VE in normally aspirated engine is less than 100 %
VE on turbo charge engine can exceed than 100 %
Anything that decreases the density, or volume of air
entering a cylinder decreases volumetric efficiency.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
74/84
MECHANICAL EFFICIENCY
Is the ratio of brake horsepower to indicated horsepowerand represents the percentage of power developed in thecylinders that reaches the propeller shaft.
E.g an engine develops 160 brake horsepower and 180indicated horsepower, the ratio of brake horsepower toindicated horsepower is 160:180, which represents amechanical efficiency of 89 percent.
The factor that has the greatest effect on mechanicalefficiency is the friction within the engine itself.
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
75/84
FACTORS THAT EFFECT VOLUMETRIC EFFICIENCY OF A
NON-TURBOCHARGED ENGINE
1. PART THROTTLE OPERATION
2. LONG, SMALLER DIAMETER INTAKE PIPES
3. INDUCTION SYSTEM SHARP BEND
4. HIGHCARBURETOR AIR TEMPERATURE
5. INCOMPLETE SCAVENGING
6. IMPROPER VALVE TIMING
7. INCREASE IN ALTITUDE
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
http://localhost/var/www/apps/conversion/tmp/scratch_9/Part%20throttle%20operation.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LONG%20SMALL%20DIAMETER%20INTAKE%20PIPES.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Induction%20systems%20with%20sharp%20bends.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/High%20CAT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Incomplete%20scavenging.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Improper%20valve%20timing.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Increases%20in%20altitude.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Increases%20in%20altitude.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Improper%20valve%20timing.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Incomplete%20scavenging.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/High%20CAT.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Induction%20systems%20with%20sharp%20bends.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/LONG%20SMALL%20DIAMETER%20INTAKE%20PIPES.ppthttp://localhost/var/www/apps/conversion/tmp/scratch_9/Part%20throttle%20operation.ppt8/12/2019 01 Introduction to Recip Engine (Ignition)
76/84
FACTORS AFFECTING POWER OF THE ENGINE
1. MANIFOLD PRESSURE
2. DETONATION AND PRE IGNITION
3. COMPRESSION RATIO
4. IGNITION TIMING
5. ENGINE SPEED
6. SPECIFIC FUEL CONSUMPTION
7. ALTITUDE
8. FUEL / AIR RATIO
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
77/84
MANIFOLD PRESSURE
CHANGE OF MANIFOLD PRESSURE AFFECT THE
AMOUNT OF POWER AN ENGINE CAN PRODUCE CONTINUE SUPPLY OF HIGH MANIFOLD PRESSURE
CAN DAMAGE THE ENGINE
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
78/84
DETONATION AND PRE-IGNITION
DETONATION IS UNCONTROL EXPLOSIVE IGNITION IN THECYLINDER
PROMOTES TO HIGH CYLINDER TEMPERATURE
CAN BE DETECT THROUGH KNOCKING IN THE ENGINE
PRE-IGNITION FUEL/AIR MIXTURE IGNITES TOO SOON CAUSE BY HOT SPOT DUE TO OVERHEATED VALVE EDGE,
SILICA DEPOSIT ON SPARK PLUG, OR RED HOT SPARK PLUGELECTRODE
DETONATION AND PREIGNITION CAN OCCURSIMULTANEOUSLY
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
79/84
COMPRESSION RATIO
A RATIO OF CYLINDER WHEN THE PISTON IS AT BDC TO WHEN THE PISTONIS AT TDC
DETERMINE THE AMOUNT OF HEAT ENERGY THAT IS CONVERT TOUSEFUL WORK
HIGH CR ALLOWS THE FUEL/AIR MIXTURE TO RELEASE ENERGYRAPIDLY AND PRODUCE MAXIMUM PRESSURE INSIDE THECYLINDER JUST AS THE PISTON BEGIN THE POWER STROKE
ONLY CAN BE INCREASED OR DECREASED BY ALTERING THE ENGINEDESIGN
CHARACTERISTIC OF AVAILABLE FUEL DETERMINE THE PRACTICALOF COMPRESSON RATIO THAT CAN BE USED IN ENGINE DESIGN
IF TURBO CHARGE ENGINE DEGREE OF TURBOCHARGING LIMIT THECOMPRESSION RATIO
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
80/84
IGNITION TIMING
CHANGE IN IN ENGINE IGNITION WILL ALSO EFFECT THE ENGINE
POWER
TO ENSURE COMPLETE COMBUSTION THE ENGINE MUST BE TIME
PROPERLY
EARLY IGNITION LOST POWER DUE TO MAXIMUM PRESSURE IN THECYLINDER BUILT TOO EARLY , AND EXPANDING GAS OPPOSED THE
ROTATIONAL INERTIA BECAUSE THE PISTON IS STILL MOVING UPWARD
GAS PRESSURE ON PISTON HEAD DOES NOT BUILD UP TO EXPECTED
LEVEL
LATE IGNITION DOES NOT ALLOW ENOUGH TIME FOR COMPLETE
COMBUSTION
CAN LEAD TO DETONATION
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
81/84
SPECIFIC FUEL CONSUMPTION
A NUMBER OF POUND OF FUEL BURN PER HR TO PRODUCE 1HORSEPOWER
IF AN ENGINE BURN 12 GALLON WHILE PRODUCING 180 BHP THEREFOREBSFC IS .4
- CALCULATION 7 X 12 = 84
- 84 DEVIDE BY 180 = .46666666666
FACTORS EFFECTING ENGINE FUEL CONSUMPTION
- ENGINE SPEED
- DESIGN
- VOLUMETRIC EFFICIENCY- FRICTION LOSSES
THE BEST FUEL CONSUMPTION IS APPROXIMATELY AT 75% POWER (CRUISING )
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
82/84
ALTITUDE
ANY TIME ENGINE IS OPERATED ABOVE SEA LEVAL LESSAIR IS DRAWN INTO THE ENGINE THUS RESULTING INDECREASE ENGINE POWER OUTPUT
DENSITY IS A TERM GIVEN TO DESCRIBE THE DENSITY OFAIR AT GIVEN ALTITUTE
EVENTHOUGH THE ACTUAL ALTITUTE DOES NOTCHANGE DENSITY ALTITUTE CAN CHANGE CONSTANTLYDUE TO CHANGE AIR TEMPERATURE
CAN BE OVERCOME BY THE USED TURBOCHARGER
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
83/84
FUEL/AIR RATIO
STOICHIOMETRIC MIXTURE IS A PERFECTLY BALANCE FUEL/AIR MIXTURE
RICH MIXTURE MORE FUEL LESS AIR E.G 14: 1.
COMBUSTIBLE FUEL AIR RATIO IS RANGE BETWEEN 8:1 TO 18:1
CONTROL MIXTUREALLOW ADJUSTMENT OF THE FUEL/AIR RATIOFROM IDLE CUT-OFF TO FULL RICH MIXTURE.
LEANING MIXTURE CAN RAISE ENGINE OPERATING TEMPERATURE
LEANING MIXTURE IS NECESSARY AS ALTITUTE INCREASE BECAUSE FUELWILL BECOME RICHER DUE TO LESS AIR AT ALTITUTE
BEST POWER MIXTURE USED DURING TAKE OFF
FOR TRAINING PURPOSE ONLY
Malaysian Institute of Aviation Technology
8/12/2019 01 Introduction to Recip Engine (Ignition)
84/84
END