ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control 1 | Page Quick Setup Guide ZDL-GSM-516-5112 A Voice Only Intercom Access Control System designed to use Mobile/Cell- phone Network. System works with any Mobile Network regardless of service provider and Network type (CDMA/GSM). System requires no major programming or computerization, just a simple plug and play type system setup. Accessible anywhere using your “Smart Phone”, edit/modify Tenant Name/Contact Phone Numbers/Add-Delete Tenant Smart (Key-Fob) Card Info/Add-Delete Tenant Entrance Unlock Code-Password and more.
19
Embed
ZDL-GSM-516-5112 Mobile Network Voice Intercom … Mobile Network Voice Intercom With Access Control 3 | P a g e System Communication Requirement: As stated, system utilizes Cell-Phone
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
1 | P a g e
Quick Setup Guide
ZDL-GSM-516-5112 A Voice Only Intercom Access Control System designed to use Mobile/Cell-
phone Network. System works with any Mobile Network regardless of service provider and Network
type (CDMA/GSM). System requires no major programming or computerization, just a simple plug and
play type system setup. Accessible anywhere using your “Smart Phone”, edit/modify Tenant
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
4 | P a g e
Initial System Assembly:
Panel consists of two parts: System Panel Mount Bracket / System Panel. System panel slide in to the
mount bracket, carefully remove mounting bracket by detaching from system panel. See illustration
below:
System Panel Housing Dimension
System Mounts Flush To Flat Surface/Wall
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
5 | P a g e
Panel With Mounting Bracket:
When detached, it will lead you to access to Main System Panel rear cover. Remove screws attached to
cover to access Main System Board (Please protect screws, Be extremely patient when performing this
process due to electro-magnetic static, and avoid touching Main Board. Be sure not to expose board to
any form of water, extreme heat, etc).
Inserting SIM-Card, 8-GB SD-Card, Antenna and other accessories will be discussed in the next page.
Exact board illustrative drawing available in next page should guide installer as to how and where to
locate SIM-Card Slot, SD-Card Slot, Power Supply input and Antenna wiring.
*****Important
Be sure to avoid connecting or placing accessories in the wrong spot as this could lead to system
operation instability.
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
6 | P a g e
System Board Diagram:
**Inserting SIM-Card
SIM-Card slot is located on the top right corner (Below SD-Card slot). (Insert Card Chip Side Down)
**Connecting Antenna
Antenna SMA Female Connector is located on the top left corner (Above System Processor). Antenna
comes with 6-feet wire; you can extend cable using SMA Coupler (female to Female). This can be
obtained at your local electronic store.
**Wiring System Power Supply
System comes with 1-15V 1.5Amp transformer, you can splice cable right in the middle and extend
wiring distance with 2-conductor wire to reach designated power source. If distance is less than 75-feet,
22-guage 2-conductor wire should be fine. But if distance exceeds 75-feet, we recommend 18-guage 2-
conductor wire. Thickness of this wire will maintain stable current flow for runs over 100-feet or more.
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
7 | P a g e
******Important Wiring Tips
It is highly recommended that you make use of included power supply. We do not recommend any third
party power supply, and if you choose to do so. Please consult system vendor to be sure that intended
third-party hardware will cause no harm/damage to system.
System Board
Wiring/Connection:
****Important (Network Configuration)
Make sure to follow wiring instruction as specified above. With loaded SIM-Card on board, nothing else
should be required to link system to public network. System should search, locate and establish
connection to the closest cell tower on its own.
Link Signal Meter/Indicator is located on the upper left corner of the screen. It will display signal link
strength between tower and system. Included antenna strength go as far as almost 2.5-miles, and it is
totally waterproof/weatherproof.
***Important*** +Linking Public Network Initial Identification by your service provider’s server actually depends on the proximity of the closest cell-tower to system location. Connecting this device to your service carrier’s network requires strong network signal to obtain successful handshake between carrier’s network and this device. If you are experiencing weak link signal, you can:
1. Take device to a different location and power on & off.
2. Relocate Antenna to higher level.
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
8 | P a g e
Electronic Lock Wiring
*****Lock Wiring Diagram Tips -5-Wire Pin Assignment: Green (NO) Blue (GND) Yellow (NC) Magnetic Locks: Mostly NC / Exit Button: White/Black Electronic Lock Power Wiring
**Wiring Tips System works with any E-lock, as long as external power is used and wired properly. Be sure to follow wiring procedure as shown. Note: You might want to consider 15V-Power Supply Box with Backup Battery to keep lock armed in the event of power outage.
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
9 | P a g e
System Main Menu:
Now that all required accessories like: SIM-Card, SD-Card, Antenna, Power Supply and E-lock (If needed)
have installed, the next step will be to power system on. System will conduct self-check each time it
powers on/off. A “Welcome” screen displays, then system “Status” screen follows: Status Screen should
display “Welcome” on top with operating instructions at the bottom as shown below. **Note: Screen
dims down (Standby Mode) after approximately 10-seconds.
**Main Screen Display Instructions
*Dial:
Means, visitors/guests can enter 3-4-digit apartment number at anytime and pressing # to dial.
*Unlock:
This feature is intended for tenants with authorized assigned CODE to gain access to the building by
simply pressing * to access code input screen. Upon display, input 6-digit assigned CODE and press # to
unlock Electronic Lock. ***Note: Default Administrative Unlock Code Is: 123456
*Menu:
By pressing #, you will be navigating to 3-major areas of which two is mainly visitors/guest features.
****Important Tips!!! Make Your Selection Using Menu Number: Instruction (1), Query (2) etc.
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
10 | P a g e
System Menu Details
***** Navigating System Menus:
# - To Confirm Your Selection / * - To Go Back/Exit / 1 – To Scroll Down / 7 – To Scroll Up
Instructions (Option-1)
**Instruction: Information about how to place calls. **Information on how to unlock e-lock with Code
Query: (Option-2) User Search (Residents) / Display All Users (Residents)
**Query: Visitors/Guest can easily locate resident in the building using this menu. There are 2-ways
visitors can search resident directory, either to search using Selection-1: Query User: Or by using the
keypad to enter tenant’s User Name (Keys Consist Of Letters/Alphabets). Selection-2: Display All Users
(Residents): Easiest way to view Tenant’s Directory. Screen displays every single resident listed in the
directory. (Note: Press 7: To Scroll Up, 1 To Scroll Down, # To Confirm Selection, * To Exit)
Set Up: (Option-3) (Main System Programming Menu Gateway)
System Main Programming Menu
***Requires Administrative Password/Code To Access. System Default Is: 123456
***Editing Tips
To Edit Password Set: Press-1, System Set: Press-2, User Set: Press-3, Capacity Set: Press-4 etc
To Exit: Press # (Enter Your Selection using Front Keypad)
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
11 | P a g e
System Main Programming Menu Cont’d
**Password Set: (Option-1)
(Note: Editing Password Set: Press-1, System Set: Press-2, User Set: Press-3, Capacity Set: Press-4 etc)
Press 1 to enter this menu. This is where you can edit Administrative Password, Administrative E-Lock
Code, and Enable/Disable Administrative E-Lock function.
**Administrative Password Tips
Default System Admin Code Is: 123456
Default Admin unlock Code Is: 123456
*To change admin password/code: Press 1, enter new 6-digit password (Numbers Only). Re-enter to
confirm password. System will authenticate changes by indicating “DONE”. Same process apply to
admin unlock code.
*Disabling Unlock Function: Automatically disables admin unlock password to function.
**System Set: (Option-2)
This section consists of questionnaire about how you choose to have system function during operation.
You can edit system Talk Time (Communication Length), Microphone Volume, Speaker Volume,
Preferred Event Archive Mode, Maximum User Capacity Setting, Date/Time/Year settings.
To edit Talk Time, Press 1. System accepts time range between 1 To 3-Minutes, enter using keypad.
To edit Microphone Volume, Press 2. System accepts volume range from 0 To 6. Key-in your choice.
To edit Speaker Volume, Press 3. Volume range is 0 To 7, enter your option
To edit Preferred Mode, Press 4, Option to Capture Visitor’s Photo or Video
(Note: Photo Capture / Video Recording Not Available In This Model).
Editing Capacity, Press 5 and enter System desired capacity (User Capacity Can Not Exceed Specification)
Editing Date/Time/Year, Press 6 to change current settings. Enter hour (Military Time format
recommended), enter minutes and Press # to skip to Year/Month/Date. Press # again to confirm.
****Navigating Setup Menu: Enter Menu Item Number To Select Menu, Press # To Exit
ZDL-GSM-516-5112 Mobile Network Voice Intercom With Access Control
12 | P a g e
User Set: (Option-3) Editing (Residents/Tenants Setup)
You can navigate to this menu anytime by pressing #, enter 3 using keypad to access Setup Gate-keeper.
And of course will demand for admin password (123456) to grant access. Option 3 should put you
directly into User Editing (Residents/Tenants) menu.
Under this menu, you will be able to setup/edit: Building Guard Post Information (Option-1), Building
Residents/Tenants Information (Option-2), Query/Look Up Tenant Record/Information (Option-3),