xA 2004-2007 xB 2004-2008 tC 2005-2007 xD 2008 99-8209 · 2010. 7. 11. · Scion tC 2005-2007 4 Disconnect the negative battery ter-minal to prevent an accidental short circuit. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8209

99-8209

APPLICATIONSSCION

xA 2004-2007 xB 2004-2008tC 2005-2007xD 2008

KIT FEATURES

• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket

A) Radio Housing • B) Brackets Set 1 • C) Brackets Set 2 • D) ISO Snap-In Brackets • E) Trim Plate

KIT COMPONENTS

A

Phillips Screwdriver • Panel Removal Tool • Socket Set

1-800-221-0932 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION

www.metraonline.com

B

C

TOOLS REQUIRED:

D E

Dash Disassembly- SCION xA 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1- SCION xB 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- SCION xB 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- SCION tC 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4- SCION xD 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Kit Assembly- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .7

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TABLE OF CONTENTS

99-8209

*Note: Refer also to the instructions included with the aftermarket radio.

99-8209 DASH DISASSEMBLY

Scion xA 2004-2007A

OFF

HI

B

OFF

HI

C

OFF

HI

D

OFF

HI

E

1

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Pull outward on the (3) climate con-trol knobs and remove. (Figure A)

2

Remove (2) Phillips screws frombehind the outer two climate knobs.(Figure B)

3

Unsnap and remove the trim pieceson each side of the climatecontrol/ashtray/pocket assembly.(Figure C)

4

Remove (2) Phillips screws from thebottom of the climate control/radiotrim panel and unsnap and removethe entire panel. (Figure D)

5

Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.(Figure E)

6

Continue to final assembly.

99-8209 DASH DISASSEMBLY

Scion xB 2004-2007

2

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Pull outward on the (3) climate con-trol knobs and remove. (Figure A)

2

Remove (2) Phillips screws frombehind the outer (2) knobs. (Figure B)

3

Unsnap and remove the entire panelsurrounding the climate controls andthe radio. (Figure C)

4

Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.

5

Continue to final assembly.

OFF

HI

A

OFF

HI

B

OFF

HI

C

99-8209 DASH DISASSEMBLY

Scion xB 2008

3

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unclip and remove the trim panelaround the radio including the a/cvents. (Figure A)

2

Unclip and remove the trim panel atthe bottom edge of the dash cavity.(Figure A)

3

Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.(Figure B)

4

Continue to final assembly.

A

B

99-8209 DASH DISASSEMBLY

Scion tC 2005-2007

4

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unsnap trim from around shifter. (Notnecessary to be removed). (Figure A)

2

Unsnap and remove panel fromaround radio. (Including climate con-trols and radio door). (Figure B)

3

Remove (2)10MM nuts from the topmounting locations and two Phillipsscrews from the bottom mountinglocations to remove the radio. (Figure C)

4

Continue to final assembly.

A

B

C

99-8209 DASH DISASSEMBLY

Scion xD 2008

5

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unclip radio trim panel. Unplug andremove panel. (Figure A)

2

Remove (4) Phillips screws securingthe radio. Unplug and remove radio.(Figure B)

3

Remove factory brackets from radio.Retain brackets for use during kitassembly. (Figure C)

4

Continue to final assembly.

A

B

C

99-8209 KIT ASSEMBLY

6

A

B

CD

Slide the Mounting Brackets onto thesides of the Radio Housing until theside clips engage. Note: Use bracketset 1 for xA, xB, and tC. Use bracketset 2 for the 2008 xB and xD. (Figure A)

1

For bracket set 1 cut and remove allmounting tabs except the tabs beingused for your application. Note: Tabsare marked xA, xB and tC. For bracketset 2 skip to step 3. (Figure B)

2

Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure C)

3

Slide the aftermarket radio into thecage until it snaps into place. (Figure D)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

DIN RADIO PROVISION WITH POCKET

99-8209 KIT ASSEMBLY

7

Slide the corresponding mountingbrackets onto the sides of the RadioHousing until the side clips engage.Note: Use bracket set 1 for xA, xB,and tC Use bracket set 2 for the 2008xB and xD. (Figure A)

1

For bracket set 1 cut and remove allmounting tabs except the tabs beingused for your application. Note: Tabsare marked xA, xB and tC. For bracketset 2 skip to step 3. (Figure B)

2

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure C)

3

Slide the radio into the radio housinguntil it snaps into place. (Figure D)

4

Snap the Trim Plate onto the front ofthe Radio Housing. (Figure D)

5

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

ISO MOUNT RADIO PROVISION WITH POCKET

A

B

CD

99-8209 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

8

NOTES

9

99-8209

99-8209 INSTRUCTIONS

1-800-221-0932 REV. 10/05/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8209

www.metraonline.com