This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC). Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re. This product is rated for indoor installation and only for dry locations. Do not modify this product beyond the instructions in this guide or the warranty will be voided. Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding Safety & Warnings Before you begin, read all warnings and installation instructions. 1. Product Parameter: WiFi-103 is a versatile RGB color control lighting system. Through WiFi function and mobile devices, the wi-103 can control various types of RGB LED lighting products VIA iOS or Android. WiFi-103 lighting control system integrates four functional controls including; dimming, color temperature adjusting, and RGB controller. The WiFi-103 can work with the optional wireless T3 controller and T3-CV Receiving controller. Communication Standard Input Voltage Max Current Load Max Output Power Product Size Weight(G.W.) 2.4 GHz Wi-Fi, 802.11 b/g/n Protocol DC12V~DC24V (Use only with Class 2 listed regulated power supply) 4A x 3CH Max 12A 144W/288W (12V/24V) L128 × W73 × H45 mm 290g WiFi-103 control system supports direct connection or by router: In directly connection, mobile phone, IOS and Android can directly control the WiFi-103 controller + T3-CV wireless control, without any third party of network equipment. Optional remote (T3) is available, if software is not used. WiFi Control Distance Working Temperature Package Size 100m -20°C ~ 40°C WiFi-103 Controller L135 x W80 x H50mm WiFi-103 WiFi Lighting Control System 1 LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s). RGB Color Change Mode 32 xed modes, 8 DIY modes Scene Mode 9 RGB modes, 3 CT (Color Temperature) modes
11
Embed
WiFi-103 WiFi Lighting Control System · Repeat the a-b-c steps if you are connecting multiple WiFi-103 controller to same wireless router. d). Exit WiFi-103 application, go to mobile
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).
Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations.
Do not modify this product beyond the instructions in this guide or the warranty will be voided.Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding
Safety & Warnings
Before you begin, read all warnings and installation instructions.
1. Product Parameter:
WiFi-103 is a versatile RGB color control lighting system. Through WiFi function and mobile devices, the wi-103 can control various types of RGB LED lighting products VIA iOS or Android.
WiFi-103 lighting control system integrates four functional controls including; dimming, color temperature adjusting, and RGB controller. The WiFi-103 can work with the optional wireless T3 controller and T3-CV Receiving controller.
Communication Standard
Input Voltage
Max Current Load
Max Output Power
Product Size
Weight(G.W.)
2.4 GHz Wi-Fi, 802.11 b/g/n Protocol
DC12V~DC24V (Use only with Class 2 listed regulated power supply)
4A x 3CH Max 12A
144W/288W (12V/24V)
L128 × W73 × H45 mm
290g
WiFi-103 control system supports direct connection or by router:In directly connection, mobile phone, IOS and Android can directly control the WiFi-103 controller + T3-CV wireless control, without any third party of network equipment. Optional remote (T3) is available, if software is not used.
WiFi Control Distance
Working Temperature
Package Size
100m
-20°C ~ 40°C
WiFi-103 Controller
L135 x W80 x H50mm
WiFi-103 WiFi Lighting Control System
1LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
RGB Color Change Mode 32 xed modes, 8 DIY modes
Scene Mode 9 RGB modes, 3 CT (Color Temperature) modes
WiFi-103 Wi-Controller
2. Conguration Diagram
www.ledworldlighting.com
Working Frequency
Input Voltage
Max Current Load
Max Output Power
Product Size
2.4GHz
DC5V~DC24V (Use only with Class 2 listed regulated power supply)
6A x 3CH Max 18A
90W/216W/432W (5V/12V/24V)
L 178 x W 48 x H 33 mm
T3-CV Receiver
3. Controller Operating Instructions
ANTENNA installation instruction
1). Install / Uninstall ANTENNARotate Antenna clockwise to install. To uninstall rotate Antenna anti-clockwise
2). Light Indicator InstructionsŸ RUN : It ashes quickly about 25s during the electric
initialization. Flashes once per second after initialization
Ÿ LINK: It keeps on when the mobile device connected with WiFi controller, and turns off when disconnected
T3 Remote Controller
Wireless Frequency
Input Voltage
Battery Capacity
Remote Distance
2.4GHz
DC5V built-in Lithium Battery
≤30mA
1000mAh
30m
Current
Standby Time
Product Size
Weight(G.W.)
≤6 months
L 145 × W 55 × H 22 mm
200g
2LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Power input/LED output
RUN
RX/TX
LINK
EXT KEY
SSID
MATCH
SCENE
SSID code switchIndicator Learning ID sceneManufacturerinterface
127.6mm
44.5mm
73m
m
RUN
RX/TX
LINK
EXT KEY
SSID
MATCH
FUN
WiFi-103 Wi-Controller
4. ios/Android application instructions:
1). Download Application:
www.ledworldlighting.com
Channel Color
3). SSID Number SettingUse code switch to set the controller's SSID Number. WiFi-103-SSID-X, X is the code switch with numerical value (from 0 to F). Which means our product could set 16 isolated LAN in the same area. The controller will re-enter initialization status once the code switch changes. RUN LED indicator light will ash quickly about 25 seconds. Search with Mobile device and connect WiFi again after Initialization nished.
4). MATCH Key and SCENE KeyShort press SCENE to the user-dened scene modes sequentially, Scene mode will cycle through scenes 1 to 9, then cycle back from scenes 9 to 1.
Restore factory settings/Delete passwordLong press MATCH key and SCENE key simultaneously more than 2 seconds, the mach ine w i l l back to the defau l t parameter, including the parameters of changing modes and network parameters.
WiFi-103 controllers will be restored and connection password will be erased to blank..
scan to download android appscan to download ios app
2). How to operate the Application:A). Network connection setting :WiFi-103 support 2 connection modes: Directly connection as router or connect by additional router.
Ÿ Connecting WiFi-103 controller as a routerGo to mobile device's WiFi setting, Search the available WiFi Network. From the list select WiFi Network, appended with SSID-Number.(As Legend-1), (no password is set by default).
IOS WiFi connectionAndroid WiFi connection
(Legend-1)
3LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Ÿ RX/TX: The indicator light turns on when the controller receives or transmits the WiFi data. Turns off in idle time
54 63 72 81 90 AF BE CD
RUN
RX/TX
LINK
EXT KEY
SSID
MATC
HSCENE
RGB scene interface CT scene interface
MATCH
SCENE
RUN
RX/TX
LINK
EXT KEY
SSID
MATCH
SCENE
Scene1 Scene2 Scene3
Scene4 Scene5 Scene6
Scene7 Scene8 Scene9
G 255255 255B 50R
PlayPlay
DIYScene Mode Device
Long press scene icons to Exchange pictures
WWW 10050
Scene1 Scene2 Scene3
50
Save
12:34 PM 100% 12:34 PM 100%
WLAN settings
WLAN
Connect to WiFi-103-SSID-0
Network notification
Auto Connect
WiFi-103-SSID-0
TP-008
ACW1F
Notify me when an open network is
available
set the way of network’s connection
Connected
Remembered, secured with WPA/
WPA2 PSK
Remembered
WLAN networks
16:0714:17 PM
Wi-FiSettings
Wi-Fi
Other...
Ask t o jin Networks
Known networks will be joined automatically.if no known networks are available, you willhave to manually select a network.
CHOOSE A NETWORK...
WiFi-103-SSID-0
WiFi-103-SSID-1
100%
www.ledworldlighting.com
Ÿ Connect WiFi-103 with a additional router:
a). Connect to the WiFi-103 controller, as same procedure as (A)b). Click WiFi-103 application icon to start the app. The app will search and list the working WiFi controller automatically
WiFi-103 Wi-Controller
c). Click Network key to enter Network interface(as legend-3-1). Turn ON connect to existing LAN option and app will search the available WiFi SSID list. Choose the available router to connect (Note : Do not choose WiFi-103 controller)(as legend-3-2 )
Repeat the a-b-c steps if you are connecting multiple WiFi-103 controller to same wireless router.
d). Exit WiFi-103 application, go to mobile wireless network setting, choose the wireless router to connect. Start WiFi-103 application again, device will list interface as legend-2-2. Complete the same steps to connect to the additional router.
(Legend 3-1)
Network interface
(Legend 3-2)
Note: In this connection mode, to avoid the mobile device automatically connect to WiFi-103 after the setting has completed, please click “workable WiFi-103". On dialog box click "Forget this network" or "Cancel save".
Cancel saved WiFi-103 connection information
4LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Version:WiFi-103.0.15
Network
WiFi-103- 02SSID-
32:AA:3C:7E:B4:DA
Disconnected
Device List
WiFi-103-SSID-01
32:AA:3C:7E:B4:DA
Network
Driver
Connect to WiFi WiFi-103...
Driver
RGB
DIM
Version:WiFi-103.0.15
Network
WiFi-103- 02SSID-
32:AA:3C:7E:B4:DA
Connect to TP-LINK1
Device List
WiFi-103-SSID-01
32:AA:3C:7E:B4:DA
Network
Driver
Connect to TP-LINK1
Driver
RGB
DIM
Delete WiFi-103 controller from list
RGB Driver mode
Disconnected WiFi-103 controller
Network interface
RGB/CT/DIM Driver settingChange the background interface
Connected additional router
Available WiFi-103
14:17 PM 100%14:17 PM 100%
Connect with additional routerWiFi-103 connected as a router
Connected to WiFi-103
Manual searching button for WiFi-103 controller
NetworkBack
User setting
Wireless mode
Connect to existing LAN
Change SSID and password
NetworkBack
Available wireless LAN networks
TP-LINK1
WiFi-103-SSID-0
WiFi103SSID1- - -
User setting
Wireless mode
Connect to existing LAN
Change SSID and password
WiFi-103-SSID-2
WiFi-103-SSID-3
WiFi-103-SSID-4
12:34 PM 100% 12:34 PM 100%
WLAN settings
WLAN
Connect to WiFi-103-SSID-0
Network notification
Auto Connect
WiFi-103-SSID-0
TP-008
ACW1F
Notify me when an open network is
available
set the way of network’s connection
Connected
Remembered, secured with WPA/
WPA2 PSK
Remembered
WLAN networks
16:07
WiFi-103-SSID-0
Cancel Forget Disconnect
StatusConnected
Signal strengthExcellent
Link speed65Mbps
SecurityOpen
IP address10.10.100.103
14:17 PM
WiFi-103-SSID-0Wi-Fi
Forget t his Netnwork
IP ADDRESS
100%
DHCP BootP Static
IP Address
Subnet Mask
Router
DNS
Search Domains
10.10.100.103
255.255.255.0
10.10.100.254
10.10.100.254
Hi_flying
www.ledworldlighting.com WiFi-103 Wi-Controller
B). RGB, CT, DIM Driver color wheel interface
C). RGB Linear Toning Interface
Click To modify linear toning interface in the RGB mode color wheel
Click on SCENE Button on the RGB driver interface. 9 scenes available in interface to choose from. The corresponding scene changing mode will display immediately, the mode parameters are displayed above the screen. Click Play key to cycle through dynamic change mode.
Click SAVE Button on the interface of RGB color wheel, linear toning, and mode. Select any Scene from 1 to 9, and click OK, the Scene name dialogue box will displayed. Scene name can be modied from dialogue box. Click OK to save current changing mode or CANCEL to Cancel the Save operation.
5LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
On application front screen, Device List interface is the default one. Click Driver into the Driver selection screen. Select the RGB/CT/DIM drive and return to the Device List interface. Click the color palette into the color palette interface, touch the color wheel to change and control the color, CT, brightness, saturation (RGB mode only) which connected to the controller, drag the brightness bar to adjust the brightness of the lighting. Click the ON / OFF button to turn off or turn on the controller. Click the save button to save scene operation.
50
GR 255 B255 255
Save
DIYScene Mode Device
12:34 PM 100%
W 255
50
RGB mode
ON/OFF
RGB Values
Brightness Slider
Selected Color
Color Wheel
Driver interface
changing mode
Linear toning Interface
Scene saving
DIY interface
Select Driver
CT
RGB
DIM
Driver interface
Driver Interface
DriverWWW 10050
Scene1 Scene2 Scene3
50
Save
12:34 PM 100% 12:34 PM 100% 12:34 PM 100%
Scene interfaceDimming modeCT mode
50
GR 197 B161 132
Save
DIYScene Mode Device
78% 64% 52%
50
GR 197 B161 132
Save
DIYScene Mode Device
78% 64% 52%
1 2 31 2 3
7 8 9
4 5 64
7
5
8
6
9
00Done
A B CA B C D E FD E F
GH IGH I J K LJ K L MNOMNO
P QRP QRSS T U VT U V WX YWX YZZ
12:34 PM 100% 12:34 PM 100%
RGB Slider
Scene Save
Brightness Slider
RGB value adjuster
RGB linear toning interface RGB value adjuster
D). RGB Scene Interface
Scene1 Scene2 Scene3
Scene4 Scene5 Scene6
Scene7 Scene8 Scene9
G 255255 255B 50R
PlayPlay
DIYScene Mode Device
Long press scene icons to Exchange pictures
12:34 PM 100%RGB Parameter Values
Long press changes the background scene
Scene modes
Dynamic scene play Button
RGB scene interface
E). RGB Scene Saving Interface
www.ledworldlighting.com WiFi-103 Wi-Controller
F). RGB Mode Interface
6LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
DeviceDIYScene Mode
Save
M1.Static red
M2.Static green
M3.Static blue
M4.Static yellow
M5.Static purple
ModeMode
Speed 8
Brightness 100%
12:34 PM 100%
DeviceDIYScene Mode
Save
M1.Static red
M2.Static green
M3.Static blue
M4.Static yellow
M5.Static purple
ModeMode
Speed 8
Brightness 100%
12:34 PM 100%
Saved to the Scene
Scene1 Scene2 Scene3
Scene4 Scene5 Scene6
Scene7 Scene8 Scene9
OKOKCancelCancel
Modify the Scene nameScene saving interface
可修改场景名称CANCELCANCEL OKOK
Scene1
Please enter the scene name Please enter the scene name
Saved to the Scene
Scene1 Scene2 Scene3
Scene4 Scene5 Scene6
Scene7 Scene8 Scene9
OKOKCancelCancel
Changing the Scene name
DeviceDIYScene Mode
Save
M1.Static red
M2.Static green
M3.Static blue
M4.Static yellow
M5.Static purple
ModeMode
Speed 8
Brightness 100%
12:34 PM 100%
Mode interface
Changing mode selection
Speed Slider
Brightness Slider
Play/Pause
Scene Saving
Static Red
Static Green
Static Blue
Static Yellow
RGB Skipping
7 Color Skipping
7 Colors Strobe
Red Fade out and Fade in
Static Purple
Static Cyan
Static White
Green Fade out and Fade in
White Strobe
Blue Fade out and Fade in
Mode Description
Adjustable Brightness
Adjustable Brightness
Adjustable Brightness
Adjustable Brightness
Adjustable Brightness
Adjustable Brightness
Adjustable Brightness
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Yellow Fade out and Fade in
Mode Description
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Purple Fade out and Fade in
Cyan Fade out and Fade in
White Fade out and Fade in
RGB Fade out and Fade in
Red Green color smooth
Red Blue color smooth
Green Blue color smooth
Red Yellow color smooth
Green Cyan color smooth
Blue Purple color smooth
Green Yellow color smooth
Blue Cyan color smooth
Red Purple color smooth
Color Changing Modes:
Blue White color smooth
Yellow/Purple/Cyan smooth
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
Adjustable Brightness/Speed
RGB color smooth
Full color gradual alternatively
www.ledworldlighting.com WiFi-103 Wi-Controller
G). DIY Interface
The Sequence for 10 color boxes is shown above. If the type of changing mode is jump, carry out the black, red, black, green, black, blue, black, yellow jump changing mode. That is red, green, blue, yellow strobe changing mode. If the changing mode is gradual, carry out the black,red, black, green, black, blue, black, yellow gradual changing mode. That is red fade out and fade in, green fade out and fade in, blue fade out and fade in, yellow fade out and fade in.
5. WiFi Network SSID Name and Password Setting
In Device list interface, click NETWORK KEY to enter Network interface. Select Change SSID and Password to enter User Setting interface. New SSID name and password must min 8 characters and consist of 0-9, a-z and A-Z. Click APPLY button on the top right corner of the interface to save the changes.
7LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
50
GR 255 B255 255
DIYScene Mode Device
S6
S7
S5
75%
87%
62%
Jump
Gradual
D3
D4
D2SPEEDBRTMODEDIY
Delete the color
by long pressing
Save
12:34 PM 100%
DIY interface
Jump/Gradual/Strobe switching
Mode D1-D8
Long press to delete current color
Brightness adjustment
Color select box
Play/Pause
Scene saving
Speed selection
Brightness selection
Color wheel
For example:
H). CT Interface
1). Select Scene:Select any scene from 1 to 3 on the CT interface,The corresponding scene changing mode will be displayed immediately. Mode parameters are as shown on screen above.
2). Save Scene:On CT (Color Temprature) interface, from the color wheel select color temperature. Click SAVE to select any scene from 1 to 3, the Scene name prompt box will displayed. Click OK to save current changing mode as Scene changing mode or click CANCEL to Cancel the Save operation.
Parameter Values
Scene
Save Scene
CT mode Scene name
Modify the Scene Name
Settings
WWW 10050
Scene1 Scene2 Scene3
50
Save
12:34 PM 100%
WWW 10050
Scene1 Scene2 Scene3
50
Save
12:34 PM 100%
可修改场景名称CANCELCANCEL OKOK
Scene1
Please enter the scene name Please enter the scene name
8
www.ledworldlighting.com WiFi-103 Wi-Controller
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
NetworkBack
User setting
Wireless mode
Connect to existing LAN
Change SSID and password
14:17 PM 100%
User Setting
SSID
Password
WiFi-103-SSID-0
Ent the new Password
Back
Restore factory settings
Change the SSID name and password Apply
14:17 PM 100%
User Setting
Accoun
Change the account name and password
SSID
Password
Ltech-WiFi-103-0
Ent the new Password
Admin
Password
Restore factory settings
Change the SSID name and password
Cancel OK
Change the SSID password
Ent the NEW Password
Ent the NEW Password again
Back
14:17 PM 100%
Device List
2 3 4
5 6 7
1
8
10 11 129
WiFi-103-SSID-0
32:AA:3C:7E:B4:DA
Network
Zone
Connect to WiFi-103-SSID-1
14:17 PM 100%
1.Device List interface 2.Network interface 3.Change SSID name interface 4.Change SSID password interface
Note: In direct connection of the WiFi-103 as a router, please close application after changing the SSID name and the password, then enter the mobile device system setting to reconnect the WiFi-103. In additional wireless router connection, it only needs to search again the WiFi-103 controller.
Note: To reset WiFi network password, simultaneously press : and more than 2s.It will delete the WiFi network password. More details in page 3 [Restore factory settings/Delete password].
MATCH SCENE
6. Remote Control Operating Instructions
1). Learning method of T3 to WiFi-103Learning ID:Short press learning key MATCH on WiFi-103 (buzzer sound), then short press any key on Remote within 5 seconds until the green LED indicator or the white one ashes 3 times (Long buzzer sound) means the controlling between remote and WiFi-103 is activated.
Cancelling ID:long press “MATCH” on WiFi-103 over 5 seconds (until long buzzer sound) means the conection between remote and WiFi-103 is cancelled.
2). T3 Remote Control Function Overview
T3
Color Circle
On/Off
Speed Control Buttons
Mode Control Buttons
Pause Key
Sync Indicator Light
Brightness Control Buttons
Saved Scenes
www.ledworldlighting.com WiFi-103 Wi-Controller
9LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
7. Conjunction Diagram
1). Wireless branch control connection:Can add branch control with T3-CV
The method of synchronization for the WiFi-103 controller and T3-CV:Learning ID: Long press the SCENE key on the WiFi-103 controller more than 2 second until the long buzzer sound. Then short press the ID on the T3-CV until the long buzzer sound. During the synchronization RUN light will ash quickly.
Cancelling ID: Long press the SCENE Key on the WiFi-103 controller untill long buzzer sound twice. It will cancel the synchronization between the WIFi-103 and T3-CV.
50 G
R255
B
255
255
Save
DIY
Scene
Mode
Settings
12:34 PM
100%
50
GR 197
B161
132
Save
DIY
SceneMode
Settings
78%
64%52%
12:34 PM100%
T3-CV
T3-CV
T3-CVT3-CV
T3-CV
Router
50
GR 255 B255 255
Save
DIYScene Mode Device
12:34 PM 100%
Mobile phone
WiFi-103
T3-CV
T3-CV
WiFi-103
T3-CV
T3-CV
www.ledworldlighting.com WiFi-103 Wi-Controller
10LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
2). Remote Distance Reference
Router
50
GR 255 B255 255
Save
DIYScene Mode Device
12:34 PM 100%
Mobile phone
WiFi-103
T3-CV
T3-CV
WiFi-103
T3-CV
T3-CV
3). LED Strip Connection
Warning: Input voltage must be identical to output voltage of the LED Fixture!
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 22 to 16 AWG gauge wire for output terminals.
WIRE 6-8 MM (0.25-0.30")
RGB mode
CT mode
121
121
121
121
121
121
121
121
RGB three-in-one LED strip
+
B
R
G
+
B
R
G
121
121
121
Two- in -One color temperature led strip
121
121
121
ww
w
511
511
331
511
511
331 331
121
121
511
511
331
511
511
331 331
+
B
R
G
+
B
R
GWiFi-103
WiFi-103
DIM mode
121
121
121
+
single color LED strip
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
WiFi-103
Class 2 Low Regulated Power SupplyL
N
AC Power50/60Hz
G
N
L tu
pnI
tu
ptu
O
V+
V-
Class 2 Low Regulated Power SupplyL
N
AC Power50/60Hz
G
N
L tu
pnI
tu
ptu
O
V+
V-
Class 2 Low Regulated Power SupplyL
N
AC Power50/60Hz
G
N
L tu
pnI
tu
ptu
O
V+
V-
www.ledworldlighting.com WiFi-103 Wi-Controller
11LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
8. Limited Warranty
We provide lifelong technical assistance with this product
A 1-year Limited factory warranty from the date of purchase. The warranty is for free repair or replacement and covers manufacturing faults only.