Vta28 Serie Gdrive

8/17/2019 Vta28 Serie Gdrive

http://slidepdf.com/reader/full/vta28-serie-gdrive 1/213

WARNING - This is a new format for application options.

If you have been accustomed to printing the application option page by usingCTL - P, be aware that the use of that key combination will cause the entire bookto print.

To print a single page, choose the File menu item at the top left of this windowand then select the Print command on the drop down menu. Then a pop-upwindow will give you the opportunity to specify whether you want to print theentire book, a group of pages or a single page.

DATA INCLUDED IN THIS BOOK IS SUBJECT TO CHANGE WITHOUT NOTICE.

Option compatibilities, option drawings, and other data listed in this book aresubject to change. Consult the Cummins IMS database for the latest informationor contact your Cummins representative. The dimensions shown in this book areincluded for comparative purposes and should not be used for other purposes.



VTA28 GENERATOR DRIVE ENGINEPRODUCT SUMMARY

October 2000

Model Configuration # ApplicationMaximum Gross BHP

1800 rpm 1500 rpm 1200 rpm

VTA28G1 D153086DX02Standby PowerPrime PowerContinuous Power

760690N.A.

675614

N.A.

N.A.N.A.N.A.

VTA28G5 D153103DX02Standby PowerPrime PowerContinuous Power

900815675

825750660

530480N.A.

* Notes:• All components and accessories are mounted and plumbed or wired unless otherwise noted.• Within the option categories that are mandatory, one option must be specified.

You are not required to select an option from the general categories.• Graphics for standard configuration options may be seen on the installation diagrams.

• [G] denotes “General Option Category”.• [M] denotes “Mandatory Option Category”.• N.A. denotes item not available.• N/A denotes item not applicable to engine.• TBA denotes item is to be determinedCaution:Proving torsional compatibility of an engine-generator set is the responsibility of the generator-set assembler. Cummins will supply the appropriate engine mass elastic data necessary for thecalculations and is prepared to offer assistance with torsional questions concerning the engine.



AC-Keydata

AC-Keydata

Option # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitte

AC 5090 Fram Model FA-362CU-1 Normal

AC 5091 Donaldson model

FVG16–0152Heavy




AC 5095 Donaldson modelFVG16–0152

Heavy

AC 5096 Fleetguard Normal



ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/ac/ac-Keydata.htm [10/9/2003 10:43:25 AM]



AC 5090

AC 5090

C — Air Cleaner

vision Date: 10/00

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/ac/ac-5090.htm (1 of 2) [10/9/2003 10:43:22 AM]



AC 5090

Option # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitted


rmal duty dry type air cleaners with caps. Fram Model FA-362CU-1 for outdoor service. For use on VTA28G1 only




AC 5091

AC 5091

C — Air Cleaner

vision Date: 10/00




AC 5091


AC 5091 Donaldson model FVG16–0152 Heavy

avy duty dry type air cleaners with cap. Donaldson model FVG16–0152 cycloflow for indoor or outdoor service for

TA28G1 use only.




AC 5092

AC 5092

C — Air Cleaner

vision Date: 10/00




AC 5092



rmal duty dry type air cleaners. Fram Model FA-362CU-1 for indoor service for VTA28G1 only.




AC 5093

AC 5093

C — Air Cleaner

vision Date: 10/00




AC 5093



rmal duty dry type air cleaners. Fram Model FA-362CU-1 for indoor service for VTA28G5 only.




AC 5094

AC 5094

C — Air Cleaner

vision Date: 10/00




AC 5094



rmal duty dry type air cleaners with caps. Fram Model FA-362CU-1 for outdoor service for VTA28G5 only.




AC 5095

AC 5095

C — Air Cleaner

vision Date: 10/00




AC 5095


AC 5095 Donaldson model FVG16–0152 Heavy

avy duty dry type air cleaners with cap Donaldson model FVG16–0152 cyclo flow for indoor or outdoor service for

TAG5 only.




AC 5096

AC 5096

C — Air Cleaner

vision Date: 10/00




AC 5096



rmal duty engine mounted air cleaners. For use in clean environments. Fleetguard disposable type. Appropriate for i

d outdoor use. For use on G1 series.




AC 5097

AC 5097

C — Air Cleaner

vision Date: 10/00




AC 5097




d outdoor use. For use on G5 series.




AC 5103

AC 5103

C — Air Cleaner

vision Date: 10/03




d outdoor use.

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/ac/ac-5103.htm [10/9/2003 10:43:25 AM]



AD-Keydata

Option # Groove Bolt Circle HP Notes

AD 5015Two grooves 6.80 dia. for 1/2

belts. One groove 5.375 dia. for

11/16 belts

AD 5020 Accessory drive without pulle

AD 5104Two grooves 6.35 dia. for 1/2

beltsRear mounted

AD-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ad/ad-keydata.htm [3/18/2002 11:28:26 AM]



AD 5015

D — Accessory Drive Pulley

evision Date: 10/00

Option # Groove Bolt Circle HP No

AD 5015Two grooves 6.80 dia. for 1/2 belts. One groove 5.375 dia. for

11/16 belts

ont mounted accessory drive pulley. Two grooves 6.80 dia. for 1/2 belts. One groove 5.375 dia. for

/16 belts. Pulley rotates opposite crankshaft at 1.5 times engine speed. Used for driving raw waterump and alternator (SW5007 and EE5021).

AD 5015

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ad/ad-5015.htm [3/18/2002 11:28:25 AM]



AD 5020


evision Date: 10/00


AD 5020 Accessory drive without pulley

ccessory drive without pulley. This option to be used where rear mounted accessory drive pulley is

ed.

AD 5020




AD 5104


evision Date: 10/00


AD 5104 Two grooves 6.35 dia. for 1/2 belts Rear mounted

ear mounted accessory drive pulley. Two grooves 6.35 dia. for 1/2 belts. Pulley rotates opposite

ankshaft at 1.5 times engine speed.

AD 5104




BR-Keydata

Option # Mounting Location Notes

BR 5006 Rear face of block. Dual hoses for venting engine

BR-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/br/br-keydata.htm [3/18/2002 11:28:27 AM]



BR 5006

R — Crankcase Breather

evision Date: 10/00

Option # Mounting Location Notes

BR 5006 Rear face of block. Dual hoses for venting engine

ual hoses for venting engine to a point below the pan ledge at the rear face of block.

BR 5006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/br/br-5006.htm [3/18/2002 11:28:27 AM]



CA-Keydata

Option # Type Plumbing Material Includes Inside Diameter

CA 8016 Indicator — — —

CA 8049 Indicator

CA-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ca/ca-keydata.htm [3/18/2002 11:28:29 AM]



A 8016

A — Air Cleaner Plumbing

vision Date: 10/00

ption # Type Plumbing Material Includes Inside Diameter

A 8016 Indicator — — —

CA 8016

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ca/ca-8016.htm (1 of 2) [3/18/2002 11:28:28 AM]



o air cleaner restriction service indicators set at 635 mm [25 in.] of water. Supplied in the kit for use with customer furnished air inta

tems.

CA 8016




A 8049

A — Air Cleaner Plumbing

vision Date: 10/00

ption # Type Plumbing Material Includes Inside Diameter

A 8049 Indicator

CA 8049




o air cleaner service indicators. Restriction set at 172 kPa (25 in. H2O). Supplied in kit.

CA 8049




CL-Keydata

Option # Description Notes

CL 8005 Twin disc SP-114–P1 Does not require clutch support

CL 8006 Twin Disc SL-214–P1 To be used with 1800 rpm or slower ratings

CL-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/cl/cl-keydata.htm [3/18/2002 11:28:31 AM]



L 8005

L — Clutch

vision Date: 10/00

ption # Description Notes

L 8005 Twin disc SP-114–P1 Does not require clutch support

in disc SP-114–P1 clutch. 307 Pilot bearing. Standard drive plates. Does not require clutch support.

CL 8005

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/cl/cl-8005.htm [3/18/2002 11:28:30 AM]



L 8006

L - Clutch

vision Date: 12/00


L 8006 Twin Disc SL-214–P1 To be used with 1800 rpm or slower ratings

in Disc model SL-214-P1 front power take-off clutch. 307 Pilot bearing and Standard drive plates. Requires clutch support. Applicat

ited to 1800 RPM.

CL 8006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/cl/cl-8006.htm [3/18/2002 11:28:31 AM]



CS-Keydata

Option # Type Kit Includes Notes

CS 5036 Manually operated fluid starting aidDoes not include fluid

starting bottle

CS 5045 240 volt single phase 4000 watt



CS 5048Coolant heater. 208 volt single phase,

4000 watt.

CS 8038 Oil Pan immersion heater — Supplied in k



CS-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/cs/cs-keydata.htm [3/18/2002 11:28:36 AM]



CS 5036

S — Injection Starting Aid

evision Date: 10/00


CS 5036 Manually operated fluid starting aid Does not include fluid starting bottle

anually operated fluid starting aid. Operated by Knob on valve assembly. Does not include fluid

arting bottle. Starting aid mounted to rear of lube oil cooler. Atomizers with two spray holes, 180

gree apart, are installed in the air manifolds.

CS 5036

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/cs/cs-5036.htm [3/18/2002 11:28:32 AM]



CS 5045


evision Date: 10/00



oolant heater 240 volt single phase 4000 watt.

CS 5045




CS 5046


evision Date: 10/00




CS 5046




CS 5047


evision Date: 10/00




CS 5047




CS 5048


evision Date: 10/00


CS 5048 Coolant heater. 208 volt single phase, 4000 watt.

oolant heater. 208 volt single phase, 4000 watt.

CS 5048




S 8038

S - Starting Aids

vision Date: 02/00

ption # Type Kit includes Notes

S 8038 Oil Pan immersion heater — Supplied in kit.

watt/120V oil pan immersion heater, supplied in kit.

tomer to mount in oil pan.

CS 8038




S 8039

S - Starting Aids

vision Date: 02/00





CS 8039




S 8045

S - Starting Aids

vision Date: 02/00





CS 8045




DA-Keydata

Option #

Fan Drive

Crank Pulley

Dia

Addt'l Drive

PulleysPTO Provision Max/Engine Rated Spee

DA 5014 7.835 inch

DA 5018 8.750 inch

DA 5054 8.750 inch

Includes drive flange

for SAE-14 FPTO

clutch

DA 5055 No pulley

DA 5073 7.835 inch 1500 RPM

DA 5074 8.750 inch

DA 5075 1500 RPM

DA-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/da/da-keydata.htm [3/18/2002 11:28:39 AM]



DA 5014

A — Vibration Damper

evision Date: 10/00

Option #Fan Drive Crank

Pulley Dia

Addt'l Drive

PulleysPTO Provision Max/Engine Rated Spe

DA 5014 7.835 inch

astic member vibration damper with 7.835 inch diameter crank pulley drive. Pulley has three groov

r 7/8 inch wide V-belts for engine mounted fan drive.

DA 5014

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/da/da-5014.htm [3/18/2002 11:28:37 AM]



DA 5018


evision Date: 10/00


Pulley Dia

Addt'l Drive


DA 5018 8.750 inch

astic member vibration damper with 8.750 inch diameter crank pulley drive. Pulley has three groov

r 3/4 inch wide V-belts for radiator mounted fan drive.

DA 5018




DA 5054


evision Date: 10/00

Option #

Fan Drive

Crank Pulley

Dia

Addt'l Drive


DA 5054 8.750 inch

Includes drive flange

for SAE-14 FPTO

clutch

astic member vibration damper without crank pulley. Vibration damper is reverse mounted. Includive flange for SAE-14 FPTO clutch.

DA 5054




DA 5055


evision Date: 10/00


Pulley Dia

Addt'l Drive


DA 5055 No pulley

astic member vibration damper without drive pulley. For heat exchanger or remote cooling.

DA 5055




DA 5073


evision Date: 10/00


Pulley Dia

Addt'l Drive


DA 5073 7.835 inch 1500 RPM

iscous vibration damper for VTA-28G5. Limited to 1500 RPM. Includes 7.835 inch diameter crank

ulley for use with three 7/8 inch wide V-belts. For engine mounted fan drive.

DA 5073




DA 5074


evision Date: 10/00


Pulley Dia

Addt'l Drive


DA 5074 8.750 inch

iscous vibration damper for VTA28G5. Limited to 1500 RPM. Includes 8.750 inch diameter crank

ulley for use with three 3/4 inch wide V-belts. For radiator mounted fan drive.

DA 5074




DA 5075


evision Date: 10/00


Pulley Dia

Addt'l Drive


DA 5075 1500 RPM

iscous vibration damper without crank pulley for VTA28G5 limited to 1500 RPM. For heat exchan

remote cooling.

DA 5075




DC-Keydata


DC 8003 Heavy duty cycle For high output/heavy duty applicatio

DC 8006 For standard power advantage rating G-driveand construction application

DC-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/dc/dc-keydata.htm [3/18/2002 11:28:40 AM]



C 8003

C - Duty Cycle

vision Date: 07/00


C 8003 Heavy duty cycle For high output/heavy duty application

high output/heavy duty application such prime power gen drive, hydraulic excavator, etc.

es prime performance parts.

DC 8003

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/dc/dc-8003.htm [3/18/2002 11:28:39 AM]



DC 8006

C — Normal Duty Cycle

evision Date: 10/00


DC 8006 For standard power advantage rating G-drive and construction application

ormal duty cycle for standard power advantage rating G-drive and construction application.

erformance parts include standard intake valves and chrome stem exhaust valves.

DC 8006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/dc/dc-8006.htm [3/18/2002 11:28:40 AM]



EA-Keydata


EA 8044 Battery charger Supplied in kit.

EA 8045 24V Automatic Cranking Panel 4 Timed Cranking Cycles.

EA-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ea/ea-keydata.htm [3/18/2002 11:28:43 AM]



A 8044

A — Electrical Accessories

vision Date: 07/00


A 8044 Battery charger Supplied in kit.

tery charger with automatic float/equalize charge mode.ludes module to indicate malfunction of battery charger.

e only with lead acid battery.

ut rating: 120, 220, or 240V, 50 or 60 Hz.

put rating: 24V, 5 amp current limited.

pplied in kit.

r use with or without engine wiring.

EA 8044

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ea/ea-8044.htm [3/18/2002 11:28:41 AM]



A 8045

A — Electrical Accessories

vision Date: 03/00


A 8045 24V Automatic Cranking Panel 4 Timed Cranking Cycles.

V automatic cranking panel with four timed cranking cycles.

ludes red alarm lights for coolant high temperature, low lubricating oil pressure, overspeed and overcrank; and one green light to ind

en selector switch is set for automatic operation.

pplied in kit.

EA 8045

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ea/ea-8045.htm [3/18/2002 11:28:42 AM]





EC 8316High Coolant Temperature Switch

—

Shuts engine down on increasi

temperature at 106 ± 1.7 °C[2

± 3 °F].

EC 8317 Low lube oil pressure switch —

Shuts engine down on

decreasing temperature at 12 ±

PSI. [83± 14 kpa].

EC 8318 Low lube oil pressure switch —

Shuts engine down ondecreasing temperature at

30 ±3 PSI.

[207 ± 21 kpa].

EC-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ec/ec-keydata.htm (2 of 2) [3/18/2002 11:28:48 AM]



C 5051

C — Thermostat

vision Date: 10/00

ption # Description Opening Temp Notes

C 5051 Used to wire all safety switches and transducers on the V28 engine

ed to wire all safety switches and transducers on the V28 engine.

EC 5051

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ec/ec-5051.htm [3/18/2002 11:28:43 AM]



EC 8023

C - Engine Controls

evision Date: 01/01

EC 8023

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ec/ec-8023.htm (1 of 2) [3/18/2002 11:28:44 AM]



Option # Description Opening Temp Notes

EC 8023 Alarm Horn and Relay — 24V

larm horn and relay to activate horn when warning lights are activated by safety control. Supplied i

t.

EC 8023




C 8160

C - Engine Controls

vision Date: 05/00


C 8160 Speed Switch — Includes crank cut-out, paralleling and overspeed shutdown contacts.

mote mount, solid state speed switch. Includes crank cut-out, paralleling and overspeed shutdown contacts.

pplied in kit.

p Crank set point: 325 RPM

allel contact set point: 800 RPM

erspeed set point: 2070 RPM

Points refer to settings when used on engines with SAE #0 flywheel with 142 teeth ring gear. When used with SAE #1 flywheel with or SAE #00 flywheel with 168 teeth, switch must be readjusted to correct speed.

quires magnetic pickup (speed sensor) for operation.

te: When used with Cummins instrument panels these switches shut the engine down and provide a signal to indicate that a

t-down took place.

EC 8160




EC 8219

C - Engine Controls

evision Date: 02/00

EC 8219




Option # Description Opening Temp Notes

EC 8219 Alarm Horn — 24V

larm Horn activated by high coolant temperature, low coolant level,

w lube oil pressure and overspeed. Relay is supplied mounted on printed circuit board container in

strument panel enclosure options.

oes not include shut-down switches. Supplied in kit.

EC 8219




C 8226

C - Engine Controls

vision Date: 01/01


C 8226 Speed Switch N/A Mounts by plugging into circuit board contained in engine instrument panel.

V electronic adjustable speed switch for overspeed shut-down. Switch operates at 350 crank termination and 1450 rpm paralleling.

erspeed operating range adjustments available are: 1725 to 2415 rpm with SAE #00 and #0 flywheel and 1725–2760 rpm with SAE#

flywheel. Requires magnetic pickup. Mounts by plugging into circuit board contained in engine instrument panel enclosure options.

EC 8226




C 8264

C — Engine Controls

vision Date: 10/00


C 8264 1.6 m [5.3 ft.] extension harness — —

ension harness. Used when remote mounting either the engine instrument panel or the generator control panel, less than 5 feet away

engine. Supplied in kit. Maximum allowable length is 22.9 m [75 ft.]

EC 8264




C 8268

C - Engine Controls

vision Date: 05/00


C 8268 4.7 m [15.3 ft] extension harness — —

ension harness. Used when remote mounting either the engine instrument panel or the generator control panel, less than 4 m [15 ft.]

m the engine.

pplied in kit. Maximum allowable length is 22.9 m [75 ft.]

EC 8268




C 8269

C - Engine Controls

vision Date: 02/00


C 8269 7.6m [25.0 ft] extension harness — —

ension harness. Used when remote mounting either the engine instrument panel or the generator control panel, less than

[25.0 ft] away from the engine.

pplied in kit. Maximum allowable length is 22.9 m ]75 ft.]

EC 8269




C 8270

C - Engine Controls

vision Date: 05/00


C 8270 15.2 m [50 ft.] extension harness — —

ension harness. Used when remote mounting either the engine instrument panel or the generator control panel, less than 15 m [50 ft.

m the engine.

pplied in kit. Maximum allowable length is 22.9 m [75 ft.]

EC 8270




C 8273

C - Engine Controls

vision Date: 01/01


C 8273 Low Lube Oil pressure switch —Shuts engine down on decreasing pressure at 83 ± 14 kPa

[12± 2 psi].

w lube oil pressure switch. Shuts engine down on decreasing pressure at 83 ± 14 kPa [12 ± 2 psi]. Fungus and corrosion resistant. Cu

plied engine wiring harness.

e: When used with Cummins instrument panels these switches shut the engine down and provide a signal to indicate that a shut-dow

ce.

EC 8273




C 8275

C - Engine Controls

vision Date: 02/00


C 8275 High Coolant Temperature Switch —Shuts engine down on increasing temperature at 106 ± 1.7 °C [223

°F].

itch shuts engine down on increasing temperature at 106 ± 1.7 °C [223 ± 3 °F]. Fungus and corrosion resistant.

EC 8275




C 8277

C - Engine Controls

vision Date: 05/00


C 8277 NFPA Switches — 5 switches

e switches functioning as follows:

o low lube oil pressure switches: one which provides an alarm on decreasing pressure at 124 ± 14 kPa [18 ± 2 psi] and a second whi

ts the engine down on decreasing pressure at 83 ± 14 kPa

± 2 psi].

o high coolant temperature switches: one which provides an alarm on increasing temperature at 102 ± 1.7 °C [215 ± 3 °F] and a seco

ch shuts the engine down on increasing temperature at± 1.7 °C [223 ± 3 °F].

eparate low coolant temperature switch which provides an alarm on decreasing temperature at 32 ± 1 °C [90 ± 2 °F].

EC 8277




C 8308

C — Thermostat

vision Date: 10/00


C 8308 Low lube oil pressure switch

w lube oil pressure switch, normally open contact opens on decreasing pressure at 12 (+ or —) 2 PSI. 83 (+ or —) 14 KPA. Fungus a

rosion resistant. Cannot be used with Cummins supplied wiring harness. For use with 64 V.D.C. nominal system. Supplied in kit.

EC 8308




C 8309

C — Thermostat

vision Date: 10/00


C 8309 High coolant temperature switch

h coolant temperature switch. Normally closed contact opens on increasing temperature at 223 (+ or —) 3 degrees F.

(+ or —) 1.7 degrees C.

ngus and corrosion resistant. Cannot be used with Cummins supplied wiring harness. For use with 64 V.D.C. nominal system. Suppl

EC 8309




C 8316

C - Engine Controls

vision Date: 08/00


C 8316 High Coolant Temperature Switch —Shuts engine down on increasing temperature at 106 ± 1.7 °C [223

°F].

itch shuts engine down on increasing temperature at 106 ± 1.7 °C [223 ± 3 °F]. Fungus and corrosion resistant.

EC 8316




C 8317

C - Engine Controls

vision Date: 08/00


C 8317 Low lube oil pressure switch — Shuts engine down on decreasing temperature at 12 ± 2 PSI. [83 ± 14 kp

uts engine down on decreasing temperature at 12 ± 2 PSI. [83 ± 14 kpa]. Fungus and corrosion resistant.

EC 8317




C 8318

C - Engine Controls

vision Date: 08/00


C 8318 Low lube oil pressure switch —

Shuts engine down on decreasing temperature at

30 ± 3 PSI.

[207 ± 21 kpa].

uts engine down on decreasing temperature at 30 ± 3 PSI

± 21 kpa].

ngus and corrosion resistant.

EC 8318




EE-Keydata

Option # Mfg/Model Voltage/Amps Notes

EE 5021Delco Remy (SI) or Leece Neville

(LN-JB)

EE 5027Delco Remy (SI) or Leece Neville

(LN-JB)

EE 8078Leece-Neville

LN 2303–JB24V/45A Built-in voltage regulat

EE 8080 Delco Remy model 20 SI 300 24V/35A Built-in voltage regulat

EE-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ee/ee-keydata.htm [3/18/2002 11:28:51 AM]



EE 5021

E — Alternator

evision Date: 10/00


EE 5021 Delco Remy (SI) or Leece Neville (LN-JB)

ounting arrangement for Delco Remy (SI) or Leece Neville (LN-JB) series alternators. Mounted ab

cessory drive shaft and driven from front accessory drive pulley 3.65 times engine speed. Includes

lts and alternator drive pulley. Does not include alternator or belt shield. Cannot be used with aummins mounted radiator or heat exchanger. Contains 34 inch belts.

EE 5021

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ee/ee-5021.htm [3/18/2002 11:28:49 AM]



EE 5027

E — Alternator

evision Date: 10/00


EE 5027 Delco Remy (SI) or Leece Neville (LN-JB)

ounting arrangement for Delco Remy (SI) or Leece Neville (LN-JB) series alternators. Mounted be

cessory drive shaft and driven from rear accessory drive shaft and driven from rear accessory drive

ulley at 2.55 times engine speed includes belts and alterntor drive pulley. Does not include alternatolt shield.

EE 5027




E 8078

E - Alternator

vision Date: 02/00

ption # Manufacturer/Model Voltage/Amps Notes

E 8078Leece-Neville

LN 2303–JB24V/45A Built-in voltage regulator

ulated 24V/45A Leece-Neville LN 2303–JB alternator with built-in voltage regulator has been approved by Underwriters Laboratori

gnite a surrounding gaseous atmosphere.

arate ground strap required.

EE 8078




E 8080

E - Alternator

vision Date: 02/00

ption # Manufacturer/Model Voltage/Amps Notes

E 8080 Delco Remy model 20 SI 300 24V/35A Built-in voltage regulator

V/35A negative ground model 20 SI 300 Delco Remy alternator with built-in voltage regulator. Includes ground strap.

EE 8080




EM-Keydata

Option # Type Attachment Hole Damper Notes

EM 5022

EM 5071 For use with mounted raw water pump

EM 5072 SAE 1–14 FPTO housing

EM 5074 Trunnion

EM-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/em/em-keydata.htm [3/18/2002 11:28:53 AM]



EM 5022

M — Front Engine Support

evision Date: 10/00


EM 5022

ont engine support for use with Cummins furnished base rails.

EM 5022

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/em/em-5022.htm [3/18/2002 11:28:52 AM]



EM 5071


evision Date: 10/00


EM 5071 For use with mounted raw water pump

ont engine support for use with mounted raw water pump. Can be used with subbase. Includes gea

vers.

EM 5071




EM 5072


evision Date: 10/00


EM 5072 SAE 1–14 FPTO housing

ont engine support and SAE 1–14 FPTO housing. Cannot be used with Cummins mounted heat

changer. Can be used with subbase. Includes gear cover.

EM 5072




M 5074


vision Date: 10/00

ption # Type Attachment Hole Damper Notes

M 5074 Trunnion

nt engine support

unting location: Front

pe: Trunnion

draulic pump compatible: Y

gree of engine tilt: )

ar cover material: Cast iron

pport material: Ductile iron

ading capability: 4.5 G

mpatible isolators: N/A

EM 5074




EP-Keydata

Option # Description

EP 5006 Engine instrument panel enclosure

EP-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ep/ep-keydata.htm [3/18/2002 11:28:54 AM]



EP 5006

P — Engine Instrument Panel

evision Date: 10/00


EP 5006 Engine instrument panel enclosure

ngine instrument panel enclosure. For mounting engine instrument panel on left side of engine. To

ar. Use only on VT/VTA-1710 engines.

EP 5006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ep/ep-5006.htm [3/18/2002 11:28:54 AM]



ES-Keydata

Option # Mounting location Notes

ES 8029 Secured to starter mounting flange 24V

ES-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/es/es-keydata.htm [3/18/2002 11:28:56 AM]



S 8029

S — Magnetic Switch

vision Date: 12/00

ption # Mounting location Notes

S 8029 Secured to starter mounting flange 24V

V insulated magnetic switch. Secured to the starter mounting flange. When engine wiring and electric starters are specified, this optio

selected.

ES 8029

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/es/es-8029.htm [3/18/2002 11:28:56 AM]



FA-Keydata

Option # Bolt Circle mm Drive Ratio Fan Center mm Tensioner Type

FA 5019 .48 to 1 539.75 [21 1/4 in.]

FA 5036 .63 to 1 488.95 [19 1/4 in.]

FA 5043 .735 to 1 457.2 [18 in.]

A-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fa/fa-keydata.htm [3/18/2002 11:28:57 AM]





FA 5036

A — Fan Drive Arrangement

evision Date: 10/00


FA 5036 .63 to 1 488.95 [19 1/4 in.]

an drive arrangement with .63 to 1 ratio and 19 1/4 inch fan centers. Cannot be used with a Cummin

rnished cooling system.

A 5036

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fa/fa-5036.htm [3/18/2002 11:28:57 AM]



FA 5043

A — Fan Drive Arrangement

evision Date: 10/00


FA 5043 .735 to 1 457.2 [18 in.]

an drive arrangement with .735 to 1 ratio and 18 inch fan centers. For use with radiator cooling.

A 5043

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fa/fa-5043.htm [3/18/2002 11:28:57 AM]



FF-Keydata

Option # Element FiltrationWater Separator/WIF

SensorLocation/Not

FF 5077

Dual spin-on water

separator/fuel filter

Contains

10–micron fuelfilters

F-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ff/ff-keydata.htm [3/18/2002 11:28:59 AM]



FF 5077

F — Fuel Filter

evision Date: 10/00

Option # Element FiltrationWater Separator/WIF

SensorLocation/No

FF 5077Dual spin-on water

separator/fuel filter

Contains

10–micron fuel

filters

ual spin-on water separator/fuel filter for stationary power applications only. Contains 10–micron f

ters.

F 5077

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ff/ff-5077.htm [3/18/2002 11:28:59 AM]



FH-Keydata

Option # SAE/Wet or Dry Application Housing Material Starter Quadrant

FH 5020 No. 2 or No. 3

H-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fh/fh-keydata.htm [3/18/2002 11:29:01 AM]



FH 5020

H — Flywheel Housing

evision Date: 10/00

Option # SAE/Wet or Dry Application Housing Material Starter Quadrant

FH 5020 No. 2 or No. 3

ywheel housing SAE No. 0 with starter mounting in No. 2 or No. 3 quadrant.

H 5020

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fh/fh-5020.htm [3/18/2002 11:29:00 AM]



FN-Keydata

Option # Type Diameter Max Speed Material

FN 4801 Blower 48 inch

FN 5601 Blower 56 inch

N-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fn/fn-keydata.htm [3/18/2002 11:29:03 AM]



N 4801

N — Fan

vision Date: 10/00

ption # Type Diameter Max Speed Material

N 4801 Blower 48 inch

nch diameter Hayless Albion manufactured fan — blower type.

N 4801

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fn/fn-4801.htm [3/18/2002 11:29:02 AM]



N 5601

N — Fan

vision Date: 10/00

ption # Type Diameter Max Speed Material

N 5601 Blower 56 inch

nch diameter fan — blower type.

N 5601

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fn/fn-5601.htm [3/18/2002 11:29:03 AM]



FP-Keydata


FP 5143

FP 5147 Woodward 2301 electronic governor with EG-1PC actuator and non AFC fuel pump

FP 5164 Woodward PSG hydraulic governor

FP 5185 Cummins electric fuel control governor (24 volt DC normally closed)

FP 5186 Cummins electric fuel control governor (24 volt DC normally closed) system

FP 5188 Woodard 2301A series

FP 5189 Woodward 2301A series

FP 8001 Carbon graphite bushing equipped gear pump

P-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fp/fp-keydata.htm [3/18/2002 11:29:06 AM]



FP 5143

P — Fuel Pump

evision Date: 10/00


FP 5143

oodward PSG hydraulic governor with:

—solid ball head

—3 slot pilot valve bushingternal droop adjutment

cludes:—AFC style PTG/auto fuel pump

—vernier throttle control

—2:1 drive ratio for 1800/1500 RPM operation

P 5143

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fp/fp-5143.htm [3/18/2002 11:29:04 AM]



FP 5147

P — Fuel Pump

evision Date: 10/00


FP 5147 Woodward 2301 electronic governor with EG-1PC actuator and non AFC fuel pump

oodward 2301 electronic governor with EG-1PC actuator and non AFC fuel pump with limiting sp

overnor. Includes control unit without load sensing. In kit.

P 5147




FP 5164

P — Fuel Pump

evision Date: 10/00


FP 5164 Woodward PSG hydraulic governor

oodward PSG hydraulic governor with external droop adjustment and 24 volt motorized head. Non

FC VS fuel pump. Includes vernier throttle control. Woodward PSG hydraulic governor with solid

ad, 3–slot pilot valve bushing, external droop adjustment and 24 volt motorized head.cludes AFC style PTG/VS fuel pump, vernier throttle control, 2:1 drive ratio for 1800/1500 RPM

peration.

P 5164




FP 5185

P — Fuel Pump

evision Date: 10/00


FP 5185 Cummins electric fuel control governor (24 volt DC normally closed)

ummins electric fuel control governor (24 volt DC normally closed) system. Fuel pump governor:

miting speed. EFC governor actuator is installed in the fuel pump AFC cavity. Requires an engine

ounted magnetic pickup. Includes a plug-in type control module installed in the engine instrumentnel or generator panel on gen sets. On g-drive the control unit to be shipped in the kit. Control mod

uires a 24 volt DC negative ground power supply. Without load sensing module.

ote: The governor actuator moves to the fully closed position with electrical failure, or shutdown.

P 5185




FP 5186

P — Fuel Pump

evision Date: 10/00


FP 5186 Cummins electric fuel control governor (24 volt DC normally closed) system

ummins electric fuel control governor (24 volt DC normally closed) system. Fuel pump governor:

miting speed, EFC governor actuator is installed in the fuel pump AFC cavity. Requires an engine

ounted magnetic pickup. Includes a control unit with speed and droop adjustments supplied in kit.ntrol unit requires a 24 volt DC negative ground power supply. without load sensing module.

ote: The governor actuator moves to the fully closed position with electrical failure, or shutdown.

P 5186




FP 5188

P — Fuel Pump

evision Date: 10/00


FP 5188 Woodard 2301A series

oodard 2301A series electronic governor with EG-1PG actuator and non-AFC fuel pump with limi

eed governor. Includes control unit with load sensing; in kit.

P 5188




FP 5189

P — Fuel Pump

evision Date: 10/00


FP 5189 Woodward 2301A series

oodward 2301A series electronic governor with EGB-IP actuator with hydraulic backup. Includes

ntrol unit with load sensing; in kit. Engine will operate in droop with hydraulic ballhead backup

overnor upon failure of electric governor. Not for use in paralleled genset applications. Non-AFC fuump with limiting speed governor.

P 5189




FP 8001

P — Fuel Pump

evision Date: 10/00


FP 8001 Carbon graphite bushing equipped gear pump

arbon graphite bushing equipped gear pump for enhanced durability. For use in place of a standard

uel pump) gear pump.

P 8001




FR-Keydata

Option # Standby HP Prime HP Ltd Prime HP Inter / Continuous

FR 5104

FR 5122 900 BHP 815 BHP

FR 5123 820 BHP 750 BHP

FR 5124 480 BHP

R-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fr/fr-keydata.htm [3/18/2002 11:29:07 AM]



R 5104

R — Fuel Rating

vision Date: 10/00

ption # Standby HP Prime HP Ltd Prime HP Inter / Continuous

R 5104

BHP at 1800 RPM and 675 BHP at 1500 RPM. For standby duty application. VTA-28G1 sales curve C-3657.

R 5104

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fr/fr-5104.htm [3/18/2002 11:29:06 AM]



R 5122

R — Fuel Rating

vision Date: 10/00


R 5122 900 BHP 815 BHP

0 RPM application:

BHP for standby power

BHP for prime power

0 RPM application:


A for prime powerL 1651

ming Code: R

A28–G5 with rubber vibration damper. Sales Curve: C4886.

R 5122




R 5123

R — Fuel Rating

vision Date: 10/00


R 5123 820 BHP 750 BHP

tricted to 1500 RPM operation.


BHP for prime power

use when engine is intended to be operated continuously at 1500 RPM.

L: 1651

ming code: RA28–G5 with viscous vibration damper

es curve: C-4886

R 5123




R 5124

R — Fuel Rating

vision Date: 10/00


R 5124 480 BHP

BHP prime power with 530 BHP overload capability at 1200 RPM.

prime power duty application

L 1176

ming Code: R

A28–G5 with rubber vibration

es curve: C-4320

R 5124




FS-Keydata

Option # Description Flow/Pressure Fitting Size Notes

FS 5020

FS 8017 Digital Load Sensing Module — — Kitted

FS 802215.2 litre [4 gal.] fuel float

tank assembly

Supplied in kit with

mounting straps

S-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fs/fs-keydata.htm [3/18/2002 11:29:09 AM]



FS 5020

S — Check Valve

evision Date: 10/00

Option # Description Flow/Pressure Fitting Size Notes

FS 5020

uel transfer pump mounted and driven through rear of front cover. Plumbed to float tank. Additiona

el strainer and check valves supplied in kit. Standard hose.

S 5020

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fs/fs-5020.htm [3/18/2002 11:29:08 AM]



S 8017

S - Fuel System Accessories

vision Date: 05/00

ption # Description Flow/Pressure Fitting Size Notes

S 8017 Digital Load Sensing Module — — Kitted

ital load sensing module for use with Cummins EFC governing system. For Isochronous parallel operation.

ludes forward and reverse power relay output signals.

vides load power indication on increasing high power level and on decreasing low power level.

pplied in kit.

ted for AC line-to-line Voltage at 50 or 60 Hz.

0/480V ± 20%5/240V ± 20% (Not Applicable)

C Governor Accessories

verning system for isochronous parallel operation.

ay be used for single generator set isochronous or droop operation when future parallel operation is anticipated.

oad sharing by 3–phase load sensing requires:

urrent transformers; included as part of the ammeter/V meter phase selector switch in customer supplied generator control panel.

ital load sensing module

ludes:

everse power relay output signal.

orward power relay output signal

ovides Load power indication onncreasing high power level

ecreasing low power level

orward power monitoring analog signal.

oad sensing module must be wired per 3032429 wiring diagram.

S 8017




S 8022

S - Fuel System Accessories

vision Date: 03/01

ption # Description Flow/Pressure Fitting Size Notes

S 8022 15.2 litre [4 gal.] fuel float tank assembly Supplied in kit with mounting straps

2 litre [4 gal.] fuel float tank assembly. Supplied in kit with mounting straps. Cannot be used on off-shore oil platforms due to operat

ularity requirements.

S 8022




FV-Keydata

Option # Volts/Description Location Notes

FV 8026 Manually operated shut-off valve

FV 8050 74 volt DC two terminal

FV 8060 Manually operated shut-off valve 24 volt DC solenoid

FV 8061 24 volt DC two terminal solenoid

FV 8063 24 volt dual coil fuel shut-off valve made by Lucifer

V-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fv/fv-keydata.htm [3/18/2002 11:29:12 AM]



V 8026

V — Fuel Shutoff Valve

vision Date: 10/00

ption # Volts/Description Location Notes

V 8026 Manually operated shut-off valve

nually operated shut-off valve. Pull to shut-off. Includes lever with swivel block for attachment to cutomer furnished cable.

V 8026

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fv/fv-8026.htm [3/18/2002 11:29:10 AM]



FV 8050


evision Date: 10/00


FV 8050 74 volt DC two terminal

4 volt DC two terminal heavy duty rapid restart fuel shutoff falve (1/4 inch N.P.T. outlet).

V 8050






FV 8061


evision Date: 10/00


FV 8061 24 volt DC two terminal solenoid

4 volt DC two terminal solenoid operated rapid restart fuel shut-off valve. (Non slotted solenoid)

V 8061




FV 8063


evision Date: 10/00


FV 8063 24 volt dual coil fuel shut-off valve made by Lucifer

4 volt dual coil fuel shut-off valve made by Lucifer. Temporary energize to open and temporary

ergize to close. Valve mounted to intake mfld. Above fuel pump.

V 8063




FW-Keydata

Option # SAE Pilot Bearing Bore Dia Ring Gear Pitch/Teeth Indicated Drive

FW 5013 #0

W-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fw/fw-keydata.htm [3/18/2002 11:29:12 AM]



FW 5013

W — Flywheel

evision Date: 10/00

Option # SAE Pilot Bearing Bore Dia Ring Gear Pitch/Teeth Indicated Drive

FW 5013 #0

AE #0 — Flywheel pilot bore.

or 18 3/8 or 22 1/2 generator flex.

isc for use when standard generator is omitted.96612 flywheel, 124507 ring gear also for use with a Cummins stubshaft.

W 5013

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/fw/fw-5013.htm [3/18/2002 11:29:12 AM]



HD-Keydata

Option # Description Mfg/Model Flange Type Shaft Typ

HD 50072 bolt SAE A type

flange

HD 5009Gear housing to be used when no

hydraulic drive is required.

HD 5010Gear housing to be used when a

hydraulic drive is required.

HD-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/hd/hd-keydata.htm [3/18/2002 11:29:14 AM]



HD 5007

D — Hydraulic Pump

evision Date: 10/00

Option # Description Mfg/Model Flange Type Shaft Type

HD 5007 2 bolt SAE A type flange

ydraulic pump drive with 2 bolt SAE A type flange and 11 tooth spline coupling. Mounts on rear o

ar housing below fuel pump. Drive ratio 1.26 to 1.

HD 5007

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/hd/hd-5007.htm [3/18/2002 11:29:13 AM]



HD 5009


evision Date: 10/00

Option # Description Mfg/Model Flange Type Shaft Ty

HD 5009Gear housing to be used when no hydraulic

drive is required.

ear housing to be used when no hydraulic drive is required.

HD 5009




HD 5010


evision Date: 10/00

Option # Description Mfg/Model Flange Type Shaft Ty

HD 5010Gear housing to be used when a hydraulic

drive is required.

ear housing to be used when a hydraulic drive is required.

HD 5010




HX-Keydata


HX 5103 Engine cooling system with heat exchanger and expansion tank

HX 5149 Heat exchanger vcooling system used with dry pulse manifold

HX-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/hx/hx-keydata.htm [3/18/2002 11:29:15 AM]



HX 5103

X — Heat Exchanger

evision Date: 10/00


HX 5103 Engine cooling system with heat exchanger and expansion tank

ngine cooling system with heat exchanger and expansion tank including liquid level gauge. Does no

clude water pump belt, guard or damper shield.

HX 5103

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/hx/hx-5103.htm [3/18/2002 11:29:15 AM]



HX 5149

X — Heat Exchanger

evision Date: 10/00


HX 5149 Heat exchanger vcooling system used with dry pulse manifold

eat exchanger cooling system used with dry pulse manifold. Includes heat exchanger, expansion tan

d liquid level gauge. Does not include water pump belt, guard or damper shield..

HX 5149

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/hx/hx-5149.htm [3/18/2002 11:29:15 AM]



M-Keydata

Option # Description Engine Model Compatability After Cooler Type

IM 5020 Two low profile cross bolt Do not use with T.C. cooler Dry exhaust

IM 5023 Two low profile cross bolt Do not use with T.C. cooler Wet exhaust

M-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/im/im-keydata.htm [3/18/2002 11:29:16 AM]



M 5020

M — Air Intake Manifold

evision Date: 10/00


IM 5020 Two low profile cross bolt Do not use with T.C. cooler Dry exhaust

wo low profile cross bolt intake manifolds. Aftercooled for use with dry exhaust manifold. Do not u

ith T.C. cooler.

M 5020

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/im/im-5020.htm [3/18/2002 11:29:16 AM]



M 5023

M — Air Intake Manifold

evision Date: 10/00


IM 5023 Two low profile cross bolt Do not use with T.C. cooler Wet exhaust

wo low profile cross bolt intake manifolds. Aftercooled for use only with wet exhaust manifold. Do

e with T.C. cooler.

M 5023

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/im/im-5023.htm [3/18/2002 11:29:16 AM]



LF-Keydata

Option # Type Hose Length Location Notes

LF 5034 Low

Do not use with Woodward

governor or dual starter

arrangements

LF 5042 HighCannot use with Woodward

governor

LF 5043Replaceable paper

elementsLow

Use with Woodward govern

F-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/lf/lf-keydata.htm [3/18/2002 11:29:17 AM]



LF 5034

F — Lubricating Oil Filter

evision Date: 10/00


LF 5034 LowDo not use with Woodward governor or dual starter

arrangements

lter-cooler assembly with spin-on elements. The water transfer pipe is in the low position. Do not u

ith Woodward governor or dual starter arrangements.

F 5034

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/lf/lf-5034.htm [3/18/2002 11:29:17 AM]



LF 5042


evision Date: 10/00


LF 5042 High Cannot use with Woodward governor

lter-cooler assembly with spin-on elements. The water transfer pipe is in the high position. Cannot

ith Woodward governor arrangements.

F 5042




LF 5043


evision Date: 10/00


LF 5043 Replaceable paper elements Low Use with Woodward governo

lter-cooler assembly with replaceable paper elements mounted on top of cooler. For use with dual

arter arrangement. May use with Woodward governor. If DL5002 and FS5016 is rquired use FT580

F 5043




OB-Keydata

Option # Location Fill Type With Dipstick Notes

OB 5016Center hand hole cover

Yes

OB 5031Center hand hole cover

Yes

OB 5037Sight glass for determining lo

lube oil level while engine is

operatin

OB-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ob/ob-keydata.htm [3/18/2002 11:29:19 AM]



OB 5016

OB — Oil Fill Arrangement

evision Date: 10/00


OB 5016 Center hand hole cover Yes

il fill tube and dip type oil gauge for use with base type sump oil pan located on center hand hole co

n right hand side (facing flywheel) bayonet calibrated for 0 degree power angle. Oil levels 102 liter

gh/80 liters low. 27 gallon high/21 gallon low. Bayonet overall length 21 5/16 inches.

OB 5016

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ob/ob-5016.htm [3/18/2002 11:29:18 AM]



OB 5031


evision Date: 10/00


OB 5031 Center hand hole cover Yes

il fill tube and dip type oil gauge for use with center sump oil pan located on center hand hole cove

n right hand side (facing flywheel) bayonet calibrated for 0 degree power angle. Oil levels 18 gallo

gh/16 gallon low (68 liters/61/liters. Bayonet overall length 21 5/16 inches.

OB 5031




OB 5037


evision Date: 10/00


OB 5037Sight glass for determining low lube oil level

while engine is operatin

ght glass for determining low lube oil level while engine is operating. Sight glass must be mounted

l pan) on fuel pump side for accurate reading.

OB 5037




OF-Keydata

Option # Element Mounted Notes

OF 5011 SingleOn oil pan ledge on right side of engine using holes No. 7

and 8 plumbed

OF 8010 Single Supplied in k

OF-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/of/of-keydata.htm [3/18/2002 11:29:20 AM]





OF 8010

OF — Oil Bypass Filter

evision Date: 10/00

Option # Element Mounted Notes

OF 8010 Single Supplied in kit

ngle element bypass engine oil filter with a spin-on cartridge. Supplied in kit.

OF 8010

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/of/of-8010.htm [3/18/2002 11:29:20 AM]



OP-Keydata

Option # Type/MaterialDrain Location

Angularity Capacity

OP 5123 Full sump base type

24 deg. front up,

23 deg. front down,30 deg. side to side

27 gallon hig

and 21 gallonlow

OP 5127 Center sump/Aluminum

35 degree front up,

30 degree front

down, 35 degree

side to side

18 gallon

high/16 gallo

low

OP 5130 Center sump basetype/Aluminum

35 degree front up,

30 degree frontdown, 35 degree

side to side.

18 gallonhigh/16 gallo

low

OP-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/op/op-keydata.htm [3/18/2002 11:29:21 AM]



OP 5123

OP — Oil Pan

evision Date: 10/00

Option # Type/Material Drain Location Angularity Capacity

OP 5123 Full sump base type

24 deg. front up, 23 deg.

front down, 30 deg. side

to side

27 gallon high and

21 gallon low

ull sump base type oil pan. Pan capacity 27 gallon high and 21 gallon low. No scavenge system.ngularity capability: 24 deg. front up, 23 deg. front down, 30 deg. side to side.

OP 5123

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/op/op-5123.htm [3/18/2002 11:29:21 AM]



OP 5127

OP — Oil Pan

evision Date: 10/00


OP 5127 Center sump/Aluminum

35 degree front up, 30

degree front down, 35

degree side to side

18 gallon high/1

gallon low

luminum center sump oil pan. Oil pan capacity 18 gallon high/16 gallon low. Angularity capabilitygree front up, 30 degree front down, 35 degree side to side. For stationary power applications only

OP 5127




OP 5130

OP — Oil Pan

evision Date: 10/00


OP 5130Center sump base

type/Aluminum

35 degree front up,

30 degree front

down, 35 degree

side to side.

18 gallon

high/16 gallon

low

luminum center sump oil pan drilled and tapped for sight glass left side. Oil pan capacity 18 gallon

gh/16 gallon low. Angularity capability 35 degree front up, 30 degree front down, 35 degree side tode. For staionary power applications only.

OP 5130




PS-Keydata

Option # Description Used With Notes

PS 8006 Scavenge Pump PS 8012 Supplied in kit

PS 8009 Oil drain valve Includes 1–18NS-2 to 1/2 NPT reducing bushing

PS-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ps/ps-keydata.htm [3/18/2002 11:29:23 AM]



S 8006

S — Scavenge Pump

vision Date: 02/00

ption # Description Used With Notes

S 8006 Scavenge Pump PS 8012 Supplied in kit

nually operated rotary sump pump for draining oil pan.ludes 760 mm [30 in.] No. 10 hose to plumb to oil pan drain.

mp and hose supplied in kit.

mps 37.85 litres [10 U.S.gal.] per 115 revolutions.

PS 8006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ps/ps-8006.htm [3/18/2002 11:29:23 AM]



S 8009

S — Scavenge Pump

vision Date: 03/01

ption # Description Used With Notes

S 8009 Oil drain valve Includes 1–18NS-2 to 1/2 NPT reducing bushing

drain valve. Includes 1–18NS-2 to 1/2 NPT reducing bushing and a 1/2 NPT ball valve.

PS 8009

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ps/ps-8009.htm [3/18/2002 11:29:23 AM]



RE-Keydata


RE 5001 Pedestal-type Use with SAE #0 flywheel housing

RE-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/re/re-keydata.htm [3/18/2002 11:29:24 AM]



RE 5001

E - Rear Engine Support

evision Date: 10/00


RE 5001 Pedestal-type Use with SAE #0 flywheel housing

edestal-type rear engine supports for use with SAE #0 flywheel housing.

RE 5001

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/re/re-5001.htm [3/18/2002 11:29:24 AM]



SA-Keydata

Option # Description PTO Clutch Support Use With

SA 5001 Front Twin disc SL-214–P1 clutch

SA-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sa/sa-keydata.htm [3/18/2002 11:29:25 AM]



SA 5001

A — Power Train Support

evision Date: 10/00

Option # Description PTO Clutch Support Use With

SA 5001 Front Twin disc SL-214–P1 clutch

ont power take-off clutch support. For use with twin disc SL-214–P1 clutch. Re-use the same

ounting capscrews that bolt the bearing housing to the clutch housing.

SA 5001

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sa/sa-5001.htm [3/18/2002 11:29:25 AM]



SG-Keydata


SG 5005 Vibration damper shield


SG 5007 Shield for accessory drive and engine water pump

SG 5008 Alternator belt shield

SG 5010 Raw water pump and alternator belt shield


SG 5015 Vibration damper shield for heat exchanger cooling


SG-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sg/sg-keydata.htm [3/18/2002 11:29:28 AM]



SG 5005

G — Alternator Guard

evision Date: 10/00



ibration damper shield. For remote cooling systems.

SG 5005

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sg/sg-5005.htm [3/18/2002 11:29:26 AM]



SG 5006


evision Date: 10/00



ibration damper shield for use with heat exchanger cooling system.

SG 5006




SG 5007


evision Date: 10/00


SG 5007 Shield for accessory drive and engine water pump

hield for accessory drive and engine water pump. May use with remote cooling or heat exchanger.

SG 5007




SG 5008


evision Date: 10/00


SG 5008 Alternator belt shield

lternator belt shield. For remote or heat exchanger cooling. For use with accessory drive pulley

ounted to rear of gear cover.

SG 5008




SG 5010


evision Date: 10/00



aw water pump and alternator belt shield. May use with heat exchanger. Cannot use with FPTO.

SG 5010




SG 5011


evision Date: 10/00



aw water pump and alternator belt shield. For use with acessory drive pulley mounted to front of ge

ver. May us with FPTO.

SG 5011




SG 5015


evision Date: 10/00


SG 5015 Vibration damper shield for heat exchanger cooling

ibration damper shield for heat exchanger cooling and front engine support suitable for mounting ra

ater pump.

SG 5015




SG 5016


evision Date: 10/00



ibration damper shield. For remote cooling system and front engine support suitable for mounting r

ater pump.

SG 5016




SP-Keydata

Option # Description Thickness Bolt Circle Dia Notes

SP 8326 Fan Spacer116 mm

[4.58 in.]

140 mm

[5.5 in.]

76 mm

[3.0 in]

fan pilot

SP-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sp/sp-keydata.htm [3/18/2002 11:29:29 AM]



P 8326

P — Fan Spacer

vision Date: 02/00

ption # Description Thickness Bolt Circle Dia Notes

P 8326 Fan Spacer116 mm

[4.58 in.]

140 mm

[5.5 in.]

76 mm

[3.0 in]

fan pilot

spacer providing a total of 116 mm [4.58 in.] of fan spacing. Fits fan hubs with 81 mm [3.18 in.] bore has 76 mm [3.0 in.] fan pilot

unting holes on 140 mm [5.5 in.] B.C.

SP 8326

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sp/sp-8326.htm [3/18/2002 11:29:29 AM]



SS-Keydata


SS 8019 Export Boxing

SS 8035 Engine Shipping Cover

SS 8050 Special handling

SS 8058 Cummins beige

SS 8078 Lubricating Oil

SS-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ss/ss-keydata.htm [3/18/2002 11:29:31 AM]



S 8019

S — Export Boxing

vision Date: 02/01

ption # Description

S 8019 Export Boxing

port Boxing. Engine Only.

SS 8019

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/ss/ss-8019.htm [3/18/2002 11:29:30 AM]



S 8035

S — Engine Shipping Cover

vision Date: 02/01

ption # Description

S 8035 Engine Shipping Cover

ntilated plastic engine cover 3 mil thick and 5080 mm [200 in.] by 2743.2 mm [108 in.].

SS 8035




S 8050

S — Special Handling

vision Date: 02/01

ption # Description

S 8050 Special handling

content option used to provide a flag to pricing that the sales order requires special handling as outlined in the shop order notes and

rge back will be required.

SS 8050




S 8058

S — Paint

vision Date: 10/00

ption # Description

S 8058 Cummins beige

mmins beige. Includes primer. Used on industrial engines.

SS 8058




S 8078

S — Lubricating Oil

vision Date: 02/00

ption # Description

S 8078 Lubricating Oil

mmins premium blue 15W40 lube oil for filling engines prior to shipment.

antity: 50.15 litres [13.25 U.S. gal.]

SS 8078




ST-Keydata

Option # Voltage/kW Mfg/ModelPinion Gear

PitchNotes

ST 5013 Ingersoll Rand/SS815

ST 5016 24 VDelco-Remy 50 MT and Ingersoll-Rand

model SS815

Use only with

high mounted

oil filter

ST 8023 24V Delco Remy 50MT 6/8 Positork driv

ST 8093 N/A Ingersoll-Rand/SS800 N/APush button

manual valve

ST 8094 24V Ingersoll-Rand/SS800 N/A Electric airstarting valve

ST 8096 N/A Ingersoll-Rand/SS800 N/A Supplied in k

ST 8127

ST-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/st/st-keydata.htm [3/18/2002 11:29:35 AM]



ST 5013

T — Starting Motor

evision Date: 10/00

Option # Voltage/kW Mfg/Model Pinion Gear Pitch Notes

ST 5013 Ingersoll Rand/SS815

gersoll Rand air starter model SS815 (positive engagement type). Option includes support bracket

ounted. For SAE #0 hsg located in #2 quadrant.

ST 5013

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/st/st-5013.htm [3/18/2002 11:29:31 AM]



ST 5016

T — Starting Motor

evision Date: 10/00

Option # Voltage/kW Mfg/ModelPinion Gear

PitchNotes

ST 5016 24 VDelco-Remy 50 MT and

Ingersoll-Rand model SS815

Use only with hig

mounted oil filter

ual starters — One electric 24 volt Delco-Remy 50 MT mountd in No. 2 quadrant and one air startegersoll-Rand model SS815 mounted in No. 3 quadrant with support bracket. Use with SAE 0 flywh

ousing. Delco-Remy starter is inslulated positive engagement. Oil sealed with long life features.olenoid angle 278 degrees type 300. Use only with high mounted oil filter.

ST 5016




T 8023

T - Starting Motor

vision Date: 02/01

ption # Voltage/kW Mfg/Model Pinion Gear Pitch Notes

T 8023 24V Delco Remy 50MT 6/8 Positork drive

V insulated ground Delco Remy 50MT starter with Bendix Positork drive. Mounted on exhaust (starboard) side of engine. Exhaust si

inlet and outlet flange drilled to 125 lb. IPS nominal ASA pipe flange standard. Includes two mating companion flanges with 8 in. N

rnal threads and two gaskets. All items supplied in kit.

ST 8023




T 8093

T - Starter

vision Date: 03/01


T 8093 N/A Ingersoll-Rand/SS800 N/A Push button manual valve

starting valves for air starters. Includes manual push button starting valve, relay valve and lubricator. Supplied in kit.

ST 8093




T 8094

T - Starting Motor

vision Date: 03/00


T 8094 24V Ingersoll-Rand/SS800 N/A Electric air starting valve

V electric air starting valve for air starters. Also includes relay valve and lubricator. Supplied in kit.

ST 8094




T 8096

T - Starting Motor

vision Date: 03/01


T 8096 N/A Ingersoll-Rand/SS800 N/A Supplied in kit

ffler for use with air starter. Supplied in kit.

ST 8096




T 8127

T - Starting Motor

vision Date: 02/00


T 8127

pressure regulator. Reduces system air pressure between 1034 - 2067 kPa [150 - 300 psi] to a working pressure of 1034 kPa [150 ps

pplied in kit.

ST 8127




SW-Keydata

Option # Description Capacity/RPM Mfg/Model

SW 500773 ft [22.25 mm] at 1800 RPM engine speed

54 ft [16.46 mm] at 1500 RPM engine speedJabsco/8150–0211

SW-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sw/sw-keydata.htm [3/18/2002 11:29:36 AM]



SW 5007

W — Raw Water Pump

evision Date: 10/00

Option # Description Capacity/RPM Mfg/Model

SW 500773 ft [22.25 mm] at 1800 RPM engine speed

54 ft [16.46 mm] at 1500 RPM engine speedJabsco/8150–0211

bsco light duty, raw water pump model 8150–0211 with 5.5 ft. (1.68M) lift capability at 61 GPM (

er/min) against a maximum head of: ft [22.25 mm] at 1800 RPM engine speed

4 ft [16.46 mm] at 1500 RPM engine speed

SW 5007

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/sw/sw-5007.htm [3/18/2002 11:29:36 AM]



TB-Keydata

Option #Mount/Exhaust Outlet

LocationWastegate Water-Cooled Notes

TB 5023 Top/Front

TB 5029For two HC3 Holset

turbochargers

Includes air crossove

connections

B-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/tb/tb-keydata.htm [3/18/2002 11:29:37 AM]



TB 5023

B — Turbocharger Arrangement

evision Date: 10/00

Option # Mount/Exhaust Outlet Location Wastegate Water-Cooled Notes

TB 5023 Top/Front

wo ST50 turbochargers top mountd. Exhaust outlets to front wet exhaust manifolds.

ir connections.

B 5023

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/tb/tb-5023.htm [3/18/2002 11:29:36 AM]



TB 5029

B — Turbocharger Arrangement

evision Date: 10/00

Option #Mount/Exhaust Outlet

LocationWastegate Water-Cooled Notes

TB 5029For two HC3 Holset

turbochargers

Includes air crossove

connections

ulsed dry exhaust manifolding for mounting two HC3 Holset turbochargers with exhaust outlet to frcludes air crossover connections.

B 5029

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/tb/tb-5029.htm [3/18/2002 11:29:37 AM]



VB-Keydata

Option # # of Isolators RTD Wgt Per Isolator

VB 5001 Six 3500 lb

VB-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/vb/vb-keydata.htm [3/18/2002 11:29:38 AM]



VB 5001

B — Vibration Isolator

evision Date: 10/00

Option # # of Isolators RTD Wgt Per Isolator

VB 5001 Six 3500 lb

et of six spring type vibration isolators. Rated at 3500 lb. per isolator. For installation between subb

d floor. Supplied in kit.

VB 5001

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/vb/vb-5001.htm [3/18/2002 11:29:38 AM]



WF-Keydata

Option # Supplier/Type Mounting DCA4 Plus Units Notes

WF 5010 Dual spin-on Right side front


WF-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wf/wf-keydata.htm [3/18/2002 11:29:39 AM]



WF 5010

WF — Corrosion Resistor

evision Date: 10/00



ual spin-on corrosion resistors. Mounted to right side front of afterooler. For use with dry type exha

anifold. Contains DC4 corrosion inhibitor sized for coolant system capapcity of 37–69 gal.

WF 5010

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wf/wf-5010.htm [3/18/2002 11:29:38 AM]



WF 5017

WF — Corrosion Resistor

evision Date: 10/00



ual spin-on corrosion resistors. Mounted to right side front of afterooler. For use with water cooled

haust manifold. Contains DC4 corrosion inhibitor sized for coolant system capapcity of 37–69 gal

WF 5017

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wf/wf-5017.htm [3/18/2002 11:29:39 AM]



WI-Keydata

Option # Inlet O.D. Orientation Notes

WI 5043 3.5 inch [89 mm]

WI-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wi/wi-keydata.htm [3/18/2002 11:29:40 AM]



WI 5043

WI — Water Inlet Connection

evision Date: 10/00

Option # Inlet O.D. Orientation Notes

WI 5043 3.5 inch [89 mm]

ater inlet connection. 3.5 inch [89 mm] O.D. Includes water pump and idler assembly.

WI 5043

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wi/wi-5043.htm [3/18/2002 11:29:39 AM]



WM-Keydata

Option # Use With/Engine Type Aftercooler type

WM 5006 Wet exhaust manifolds Not for T.C. cooler

WM 5018 Dry pulse type manifold

WM-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wm/wm-keydata.htm [3/18/2002 11:29:41 AM]



WM 5006

WM — Water Manifold

evision Date: 10/00


WM 5006 Wet exhaust manifolds Not for T.C. cooler

hermostats and thermostat housings without separate water manifolds for use with wet exhaust

anifolds. Aftercooled, not for T.C. cooler.

WM 5006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wm/wm-5006.htm [3/18/2002 11:29:41 AM]



WM 5018

WM — Water Manifold

evision Date: 10/00


WM 5018 Dry pulse type manifold

ater manifolding. For use with dry pulse type exhaust manifold. Requires dependent option WM57

WM5702 water bypass connection. Includes boss with 1/8' N.P.T.F. thread.

WM 5018

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wm/wm-5018.htm [3/18/2002 11:29:41 AM]



WO-Keydata

Option # Outlet O.D. Orientation Notes

WO 5006 Straight up For use with remote cooling

WO 5008 45 degree from horizontal plane For use with Cummins mountradiator cooling system

WO 5011 Pointing forward

WO 5012 Straight up For use with radiator cooling

WO 5014front of engine 90 degree from

vertical planeUse with EXPAB

WO-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wo/wo-keydata.htm [3/18/2002 11:29:43 AM]



WO 5006

WO — Water Outlet Connection

evision Date: 10/00


WO 5006 Straight up For use with remote cooling

ual water outlet connections. For use with dry type exhaust manifolds. Outlets point straight up. Fo

ith remote cooling.

WO 5006

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/wo/wo-5006.htm [3/18/2002 11:29:42 AM]



WO 5008


evision Date: 10/00


WO 5008 45 degree from horizontal planeFor use with Cummins mounted radia

cooling system

ual water outlet connections. For use with dry type exhaust manifolds. Outlets point to front of eng

45 degree from horizontal plane. For use with Cummins mounted radiator cooling system.

WO 5008




WO 5011


evision Date: 10/00


WO 5011 Pointing forward

ual water outlet connections pointing forward. For use with wet type exhaust manifolds and Cumm

ounted heat exchanger.

WO 5011




WO 5012


evision Date: 10/00


WO 5012 Straight up For use with radiator cooling

ual water outlet connections. For use with wet type exhaust manifolds. Outlets point straight up. Fo

e with radiator cooling on generator sets.

WO 5012




WO 5014


evision Date: 10/00


WO 5014 front of engine 90 degree from vertical plane Use with EXPAB

ual water outlet connections. For use with dry pulse type exhaust manifolds. Outlets point toward f

engine 90 degree from vertical plane. Use with EXPAB.

WO 5014




XS-Keydata

Option # Description Connection O.D. Marmon Type Notes

XS 8014Two 90 degree turbocharger

exhaust elbows5 inch [127 mm]

XS 8030 Two flexible exhaust tubing 8–bolt flang

XS 8031Two 127 mm [5 in.] I.D. clamp

type flexible exhaust tubing

XS 8070Dual flanged exhaust expansion

adapters

XS 8092

Two 90 degree turbocharger

ehaust elbows with 5 inch [127mm] I.D. flange type exhaust

outlets

XS-Keydata

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/xs/xs-keydata.htm [3/18/2002 11:29:48 AM]



S 8014

S — Exhaust Outlet Connection

vision Date: 10/00

ption # Description Connection O.D. Marmon Type Notes

S 8014 Two 90 degree turbocharger exhaust elbows 5 inch [127 mm]

o 90 degree turbocharger exhaust elbows with 5 inch [127 mm] O.D. exhaust outlets..

XS 8014

ttp://marketingtechdata.cummins.com/curves/database/options/vta28g/vta28g/xs/xs-8014.htm [3/18/2002 11:29:44 AM]



S 8030


vision Date: 03/01


S 8030 Two flexible exhaust tubing 8–bolt flange

o 127 mm [5 in.] I.D. 610 mm [24 in.] long flanged flexible exhaust tubing with outlet flange drilled to 125 lb, 127 mm [5 in.] nomi

A pipe flange standard includes two gaskets for inlet flange. Supplied in kit.

XS 8030




S 8031


vision Date: 03/01


S 8031 Two 127 mm [5 in.] I.D. clamp type flexible exhaust tubing

o 127 mm [5 in.] I.D. clamp type flexible exhaust tubing 610 mm [24 in.] length and four U-bolt clamps. Supplied in kit.

XS 8031




S 8070


vision Date: 10/00


S 8070 Dual flanged exhaust expansion adapters

al flanged exhaust expansion adapters. For adapting 5 inch flanged flexible exhaust tubing to 6 inch exhaust silencers. Includes four

kets and two companion flanges with 6 inch internal thread. Supplied in kit.

XS 8070




S 8092


vision Date: 10/00

XS 8092

Vta28 Serie Gdrive

Documents