user manual pco.Silicon Software grabber & driver installation

pco.Silicon Software grabber & driver installation

pco.

user manual

2

PCO asks you to read this manual carefully before using the Silicon Software runtime installation and follow the instructions.

In case of any questions or comments, please contact us at PCO.

telephone +49 (0) 9441 2005 50

fax +49 (0) 9441 2005 20

email [email protected]

postal address PCO AG Donaupark 11 93309 Kelheim, Germany

The cover photo shows an exemplary PCO camera system. The lens is sold separately.

Copyright © 2017 PCO AG (called PCO hereinafter), Kelheim, Germany. All rights reserved. PCO assumes no responsibility for errors or omissions in these materials. These materials are provided as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, or non-infringement. PCO further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. PCO shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. The information is subject to change without notice and does not represent a commitment on the part of PCO in the future. PCO hereby authorizes you to copy documents for non – commercial use within your organization only. In consideration of this authorization, you agree that any copy of these documents, which you make, shall retain all copyright and other proprietary notices contained herein. Each individual document published by PCO may contain other proprietary notices and copyright information relating to that individual document. Nothing contained herein shall be construed as conferring by implication or otherwise any license or right under any patent or trademark of PCO or any third party. Except as expressly provided, above nothing contained herein shall be construed as conferring any license or right under any PCO copyright. Note that any product, process, or technology in this document may be the subject of other intellectual property rights reserved by PCO, and may not be licensed hereunder.

Released October 2017 © PCO AG

By Martin Blaschke & Thomas Hartmann pco.Silicon Software driver & grabber installation Manual V1.00 © PCO AG, Germany

3

TABLE OF CONTENTS

1. INTRODUCTION 4

1.1 INSTALLATION ORDER 4

2. DRIVER INSTALLATION 5

3. INSTALL GRABBER CARD TO PC 7

4. MICRO DIAGNOSTICS TOOL 8

4.1 MEIV GRABBER FIRMWARE UPGRADE 8

4.2 MEV GRABBER FIRMWARE UPGRADE 10

4.3 PERFORMANCE TEST 12

ABOUT PCO 13

TOP

4

1 INTRODUCTION

1. INTRODUCTION

Instructions for installing and testing the Silicon Software microEnable IV (mEIV) Camera Link grabber card and the Silicon Software micro Enable V (mEV) Camera Link HS grabber card for Microsoft Windows operating systems. These cards are required to be able to use a pco.edge with Camera Link interface or Camera Link HS interface. Frame grabber installation must be performed by a technician, because high voltages can occur on single parts of your computer. Please install the correct version according to your Windows Operating system. On 64bit systems the 32bit runtime must be installed additionally, if 32bit applications have to be used.

1.1 INSTALLATION ORDER

First Step Runtime

Install Silicon software runtime installation See chapter 2

Second Step Grabber Card

Install grabber card to your computer See chapter 3

Third Step microDiagnostics

Run microDiagnostics Tool See chapter 4

Fourth Step Firmware Upgrade

Update the firmware of your grabber card Follow the instructions:

mEIV grabber See chapter 4.1

mEV grabber See chapter 4.2

Fifth Step Perfomance

Apply Board & Performance test See chapter 4.3

Final Step Start Camware

5

2 DRIVER INSTALLATION

2

3

1

2. DRIVER INSTALLATION

Install the latest Silicon Software runtime package (Download: http://www.pco.de/support/) Follow the steps in this order.

Uninstall former versions of Silicon Software runtime. Select Destination Location. Select Full Installation. If you want to save disk space deselect documentation and frame grabber SDK.

6

2 DRIVER INSTALLATION

4

5

6

7

Select the name of the start menu folder or select “Don’t create a Start Menu folder” (not recommended). Select Additional Tasks: only select “Update device drivers”. Ready to install. Confirm the selection to start the install. After installation is finished, it is necessary to restart your computer. After restarting , start the microDiagnostics tool (see chapter 4).

7

3 INSTALL GRABBER CARD TO PC

3. INSTALL GRABBER CARD TO PC

The Silicon Software frame grabber card must be installed to your computer.

ELECTRIC SHOCK WARNING DUE TO VOLTAGE PARTS INSIDE Risk of injury due to electric shock.

Always pull mains plug before opening the computer.

Installation of new components to a computer should only be performed by a technician or qualified personal.

• Shutdown your computer • Unplug it from mains • Open the computer case • Install the frame grabber card to a proper slot

o mEIV: PCI Express x4 (Gen1), DMA900 o mEV: PCI Express x4 (Gen 2), DMA1800

• Start your computer

Device manager:

The grabber card should be displayed within the device manager. If the device is not shown this way, please reinstall the Silicon Software device driver.

Windows short-cut for device manager: press windows + pause/break key.

WARNING

1

2 1 2

8

4 MICRO DIAGNOSTICS TOOL

4

1 2

3

4. MICRO DIAGNOSTICS TOOL

microDiagnostics Tool works with mEIV (AD4 / VD4) and mEV frame grabber cards.

Run various diagnostic routines directly on the frame grabber, including Applets test, Board test, Performance test.

4.1 MEIV GRABBER FIRMWARE UPGRADE

Upgrade to the latest firmware for your Silicon Software mEIV frame grabber.

This is only necessary, if the latest firmware is not installed to your frame grabber!

Click Firmware.

Click Load new applet.

Select the appropriate hap file.

Click Flash Now.

3

4

1

2

9

4 MICRO DIAGNOSTICS TOOL

Flash Dialog opens. Click Flash.

Now it is successfully flashed. Close this dialog.

You must shut down (a restart is insufficient) your computer completely after the firmware upgrade for the changes to take effect.

Last step: Select Diagnosis → Applets Result must be: succeeded.

6

5

5

6

10

4 MICRO DIAGNOSTICS TOOL

1

3

4

5

2

4.2 MEV GRABBER FIRMWARE UPGRADE

This is only necessary, if the latest firmware is not installed to your frame grabber! First test, if a proper firmware version is installed. Select Diagnosis → Applets If test result is skipped an update is required. Select Diagnosis → Firmware The current Applet must be updated. Click Load new applet and select the new

Acq_DualCLHSx1AreaRAW DLL. Click Open.

Click Flash Now.

1

2

3

4

5

11

4 MICRO DIAGNOSTICS TOOL

6

7

8

9

Flash Dialog opens. Click Flash. Now it is successfully flashed. Close this dialog.

Please restart all applications using the board. Select Diagnosis → Applets Now the Result is succeeded. PCO cameras only use the AcqDualCLHS DLL.

6

7

12

4 MICRO DIAGNOSTICS TOOL

4.3 PERFORMANCE TEST

To test the board, open Diagnosis menu and click Board to start the test.

All tests should succeed.

Test the performance: click Performance to start the test.

It is mandatory that the board PCIe is Highspeed Capable. Otherwise the board is probably not able to transfer the necessary data rate.

These two screenshots show achievable data rates for mEIV and mEV boards.

For further information or problems with mainboards please contact PCO support section.

2

1

1

2

3

4

3 4

13

ABOUT PCO

ABOUT PCO

In 1987, PCO was founded with the objective to develop and to produce specialized, fast and sensitive video camera systems, mainly for scientific applications. Meanwhile the product range of PCO cameras covers digital camera systems with high dynamic range, high resolution, high speed and low noise, which are sold in the scientific and industrial market all over the world.

Currently PCO is one of the leading manufacturers of scientific cameras. Worldwide representatives, together with our own sales department and technical support assure that we keep in touch with our customers and their needs. The actual wide range of specialized camera systems is the result of technical challenge and product specific know-how. A design according to advanced techniques, a high standard of production and strict quality controls guarantee a reliable operation of the cameras. Our own developments in conjunction with an excellent contact to leading manufacturers of image sensors ensure our access to state-of-the-art CCD- and CMOS-technology for our cameras. Since 2001, PCO is located in its own facility building in Kelheim at the shore of the beautiful and international river Danube. Here in the county Bavaria, which is well known for its excellent support and conditions for high technology companies, we share the benefits of the simple access to high performance products and services in the surrounding area.

Kelheim itself is a historical town, first documented in 866. The small city is founded at the confluence of the Danube and the Altmühl, which has been converted into the Rhine-Main-Danube bypass channel for water transport. Located in Danube-valley, it is the heart of a beautiful river and forest covered lime plateau landscape. It´s landmark, the Hall of Liberation, was built by Ludwig I. in 1863 on the Mount Michael and is visible from all over the city and valley. The beautiful Danube-Gorge, which is protected as natural monument since 1840, is located between Kelheim and the famous abbey Weltenburg.

pco.

pco.