WNER’S MANUAL 5EK-28199-E1 TW125 Downloaded from www.Manualslib.com manuals search engine
Dec 25, 2015
OWNER’S MANUAL
5EK-28199-E1
TW125
5EK-9-E1 Hyoshi3.3P-BLUE 4/6/0 11:47 PM Page 1 (2,1) (Cyan plate)
Downloaded from www.Manualslib.com manuals search engine
siro page 4/6/0 3:58 AM Page 1
Downloaded from www.Manualslib.com manuals search engine
EAU00001
INTRODUCTION
1
2
3
4
5
6
7
8
9
Welcome to the Yamaha world of motorcycling!
As the owner of a TW125, you are benefiting from Yamaha’s vast experience in and newesttechnology for the design and the manufacture of high-quality products, which have earnedYamaha a reputation for dependability.
Please take the time to read this manual thoroughly, so as to enjoy all your TW125’s advan-tages. The owner’s manual does not only instruct you in how to operate, inspect and maintainyour motorcycle, but also in how to safeguard yourself and others from trouble and injury.
In addition, the many tips given in this manual will help to keep your motorcycle in the bestpossible condition. If you have any further questions, do not hesitate to contact your Yamahadealer.
The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 1
Downloaded from www.Manualslib.com manuals search engine
EAU00005
IMPORTANT MANUAL INFORMATION
1
2
3
4
5
6
7
8
9
Particularly important information is distinguished in this manual by the following notations:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
Failure to follow WARNING instructions could result in severe injury or death to the
motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
A CAUTION indicates special precautions that must be taken to avoid damage to
the motorcycle.
A NOTE provides key information to make procedures easier or clearer.
Q
w
cC
NOTE:
NOTE:
8 This manual should be considered a permanent part of this motorcycle and shouldremain with it even if the motorcycle is subsequently sold.
8 Yamaha continually seeks advancements in product design and quality. Therefore,while this manual contains the most current product information available at the timeof printing, there may be minor discrepancies between your motorcycle and this manu-al. If there is any question concerning this manual, please consult your Yamaha dealer.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 2
Downloaded from www.Manualslib.com manuals search engine
IMPORTANT MANUAL INFORMATION
1
2
3
4
5
6
7
8
9
EW000002
w
PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS
MOTORCYCLE.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 3
Downloaded from www.Manualslib.com manuals search engine
1
2
3
4
5
6
7
8
9
TW125
OWNER’S MANUAL
©1999 by Yamaha Motor Co., Ltd.
1st Edition, May 1999
All rights reserved. Any reprinting or
unauthorized use without the written
permission of Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in Japan.
EAU00008
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 4
Downloaded from www.Manualslib.com manuals search engine
EAU00009
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
1
5
GIVE SAFETY THE RIGHT OF WAY ..................1-1
DESCRIPTION.....................................................2-1Left view............................................................2-1Right view.........................................................2-2Controls/Instruments .......................................2-3
INSTRUMENT AND CONTROLFUNCTIONS........................................................3-1
Main switch ......................................................3-1Indicator lights..................................................3-1Speedometer ....................................................3-2Handlebar switches..........................................3-2Clutch lever.......................................................3-4Shift pedal.........................................................3-4Front brake lever ..............................................3-4Rear brake pedal ..............................................3-5Fuel tank cap.....................................................3-5Fuel....................................................................3-6Fuel cock ...........................................................3-7Starter (choke) “1”.........................................3-8Steering lock.....................................................3-8Seat ...................................................................3-9Helmet holder...................................................3-9Rear shock absorber ......................................3-10Rear carrier .....................................................3-10Luggage strap holders...................................3-10
Sidestand........................................................3-11Sidestand/clutch switch operation check.....3-12
PRE-OPERATION CHECKS.................................4-1Pre-operation check list ...................................4-1
OPERATION AND IMPORTANT RIDINGPOINTS................................................................5-1
Starting the engine ..........................................5-1Starting a warm engine...................................5-4Shifting..............................................................5-4Tips for reducing fuel consumption ...............5-5Engine break-in ................................................5-5Parking ..............................................................5-6
PERIODIC MAINTENANCE AND MINORREPAIR ................................................................6-1
Tool kit ..............................................................6-1Periodic maintenance and lubrication............6-3Cowling and panel removal andinstallation ........................................................6-6Panel A..............................................................6-6Panel B ..............................................................6-7Cowling C..........................................................6-8Spark plug.........................................................6-8Engine oil ..........................................................6-9Air filter ...........................................................6-12
1
2
3
4
6
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 5
Downloaded from www.Manualslib.com manuals search engine
Carburetor adjustment ..................................6-14Idle speed adjustment ...................................6-14Throttle cable free play inspection ...............6-15Valve clearance adjustment ..........................6-15Tires.................................................................6-16Wheels ............................................................6-18Clutch lever free play adjustment.................6-19Front brake lever free play adjustment ........6-19Rear brake pedal height and free playadjustment......................................................6-20Brake light switch adjustment.......................6-21Checking the front brake pads andrear brake shoes.............................................6-22Inspecting the brake fluid level .....................6-22Brake fluid replacement.................................6-23Drive chain slack check..................................6-24Drive chain slack adjustment ........................6-24Drive chain lubrication...................................6-25Cable inspection and lubrication ..................6-26Throttle cable and grip lubrication ...............6-26Brake and shift pedal lubrication..................6-27Brake and clutch lever lubrication ................6-27Sidestand lubrication.....................................6-27Rear suspension lubrication..........................6-28Front fork inspection......................................6-28Steering inspection........................................6-29Wheel bearings ..............................................6-29
Battery.............................................................6-30Fuse replacement...........................................6-31Headlight bulb replacement..........................6-32Turn signal and taillight bulb replacement....................................................6-33Supporting the motorcycle ...........................6-34Front wheel removal......................................6-35Front wheel installation.................................6-36Rear wheel removal .......................................6-36Rear wheel installation ..................................6-37Troubleshooting.............................................6-38Troubleshooting chart ...................................6-39
MOTORCYCLE CARE AND STORAGE..............7-1Care ...................................................................7-1Storage..............................................................7-4
SPECIFICATIONS................................................8-1How to use the conversion table ....................8-5
CONSUMER INFORMATION.............................9-1Identification numbers record.........................9-1Key identification number...............................9-1Vehicle identification number.........................9-1Model label .......................................................9-2
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
7
8
9
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 6
Downloaded from www.Manualslib.com manuals search engine
1-1
EAU00021
Q GIVE SAFETY THE RIGHT OF WAY
1
2
3
4
5
6
7
8
9
Motorcycles are fascinating vehicles, which can give you an unsurpassed feeling of power andfreedom. However, they also impose certain limits, which you must accept; even the bestmotorcycle does not ignore the laws of physics.
Regular care and maintenance are essential for preserving your motorcycle’s value and operat-ing condition. Moreover, what is true for the motorcycle is also true for the rider: good perfor-mance depends on being in good shape. Riding under the influence of medication, drugs andalcohol is, of course, out of the question. Motorcycle riders - more than car drivers - mustalways be at their mental and physical best. Under the influence of even small amounts ofalcohol, there is a tendency to take dangerous risks.
Protective clothing is as essential for the motorcycle rider as seat belts are for car drivers andpassengers. Always wear a complete motorcycle suit (whether made of leather or tear-resistantsynthetic materials with protectors), sturdy boots, motorcycle gloves and a properly fitting hel-met. Optimum protective wear, however, should not encourage carelessness. Though full-cov-erage helmets and suits, in particular, create an illusion of total safety and protection, motorcy-clists will always be vulnerable. Riders who lack critical self-control run the risk of going toofast and are apt to take chances. This is even more dangerous in wet weather. The good motor-cyclist rides safely, predictably and defensively - avoiding all dangers, including those causedby others.
Enjoy your ride!
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 7
Downloaded from www.Manualslib.com manuals search engine
2-1
EAU00026
DESCRIPTION
1
2
3
4
5
6
7
8
91. Fuel tank (page 3-5)2. Fuel cock (page 3-7)3. Helmet holder (page 3-9)4. Luggage straps (page 3-10)
5. Shift pedal (page 3-4)6. Air filter (page 6-12)7. Chain adjusting plates (page 6-24)
1 2 3 4
5 6 7
Left view
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 8
Downloaded from www.Manualslib.com manuals search engine
2-2
DESCRIPTION
1
2
3
4
5
6
7
8
98. Rear carrier (page 3-10)9. Battery (page 6-30)
10. Fuse (page 6-31)
11. Tool kit (page 6-1)12. Rear brake pedal (page 3-5, 6-20)13. Engine oil level check window (page 6-9)
8 9
10 11 12 13
Right view
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 9
Downloaded from www.Manualslib.com manuals search engine
2-3
DESCRIPTION
1
2
3
4
5
6
7
8
914. Clutch lever (page 3-4, 6-19)15. Left handlebar switches (page 3-2)16. Speedometer (page 3-2)17. Starter (choke) (page 3-8)18. Main switch (page 3-1)
19. Indicator lights panel (page 3-1)20. Right handlebar switches (page 3-3)21. Front brake lever (page 3-4, 6-19)22. Throttle grip (page 6-15, 6-26)23. Fuel tank cap (page 3-5)
14 15 16 17 18 19 20 21 22
23
Controls/Instruments
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 10
Downloaded from www.Manualslib.com manuals search engine
3-1
EAU00027
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU00028
Main switchThe main switch controls the igni-tion and lighting systems. Its oper-ation is described below.
EAU00036
ON
Electrical circuits are switched on.The engine can be started. The keycannot be removed in this position.
EAU00038
OFF
All electrical circuits are switchedoff. The key can be removed in thisposition.
EAU00056
Indicator lights
EAU00057
Turn indicator light “5”
This indicator flashes when theturn switch is moved to the left orright.
EAU00063
High beam indicator light “&”
This indicator comes on when theheadlight high beam is used.
1. Turn indicator light “5”2. High beam indicator light “&”3. Neutral indicator light “N”
EAU00061
Neutral indicator light “N”
This indicator comes on when thetransmission is in neutral.
OFFON 31 2
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 11
Downloaded from www.Manualslib.com manuals search engine
3-2
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU01087
SpeedometerThe speedometer shows ridingspeed. This speedometer isequipped with an odometer andtrip odometer. The trip odometercan be reset to “0” with the resetknob. Use the trip odometer toestimate how far you can ride on atank of fuel. This information willenable you to plan fuel stops in thefuture.
1. Reset knob2. Speedometer3. Odometer4. Trip odometer
EAU00118
Handlebar switchesEAU00121
Dimmer switch
Turn the switch to “&” for thehigh beam and to “%” for the lowbeam.
1. Lights switch2. Dimmer switch 3. Turn signal switch 4. Horn switch “*”
NOTE:
(for German model equipped withspeed limiter only)This motorcycle is equipped with aspeed limiter which prevents itfrom exceeding a top speed of 80km/h.
1
2
3
4
4
1
2
3
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 12
Downloaded from www.Manualslib.com manuals search engine
3-3
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU00127
Turn signal switch
To signal a right-hand turn, pushthe switch to “6”. To signal a left-hand turn, push the switch to“4”. Once the switch is releasedit will return to the center position.To cancel the signal, push theswitch in after it has returned tothe center position.
EAU00129
Horn switch “*”
Press the switch to sound the horn.
EAU00134
Lights switch
Turning the light switch to “'”,turns on the auxiliary light, meterlights and taillight. Turning thelight switch to “:” turns the head-light on also.
EAU00143
Start switch “,“
The starter motor cranks theengine when pushing the startswitch.
EC000005
cC
See starting instructions prior to
starting the engine.
1
2
EAU00138
Engine stop switch
The engine stop switch is a safetydevice for use in an emergencysuch as when the motorcycle over-turns or if trouble occurs in thethrottle system. Turn the switch to“#” to start the engine.In case of emergency, turn theswitch to “$” to stop the engine.
1. Engine stop switch 2. Start switch “,”
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 13
Downloaded from www.Manualslib.com manuals search engine
3-4
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU00157
Shift pedalThis motorcycle is equipped with aconstant-mesh 5-speed transmis-sion.The shift pedal is located on theleft side of the engine and is usedin combination with the clutchwhen shifting.
1. Shift pedalN. Neutral
EAU00152
Clutch leverThe clutch lever is located on theleft handlebar, and the ignition cir-cuit cut-off system is incorporatedin the clutch lever holder. Pull theclutch lever to the handlebar to dis-engage the clutch, and release thelever to engage the clutch. Thelever should be pulled rapidly andreleased slowly for smooth clutchoperation. (Refer to the enginestarting procedures for a descrip-tion of the ignition circuit cut-offsystem.)
1. Clutch lever
EAU00158
Front brake leverThe front brake lever is located onthe right handlebar. Pull it towardthe handlebar to apply the frontbrake.
1. Front brake lever
1 1
1
N
5432
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 14
Downloaded from www.Manualslib.com manuals search engine
3-5
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU00162
Rear brake pedalThe rear brake pedal is on the rightside of the motorcycle. Press downon the brake pedal to apply therear brake.
1. Rear brake pedal
EAU01498
Fuel tank capTo open
Insert the key and turn it 1/4 turncounterclockwise. Open the cap byturning it counterclockwise.
To close
Turn the cap clockwise with thekey inserted. To remove the key,turn it clockwise to the originalposition.
1. Fuel tank cap
NOTE:
This tank cap cannot be closedunless the key is in the lock. Thekey cannot be removed if the cap isnot locked properly.
EW000023
w
Be sure the cap is properly
installed and locked in place
before riding the motorcycle.
1 1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 15
Downloaded from www.Manualslib.com manuals search engine
3-6
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
1
2
EAU01183
FuelMake sure there is sufficient fuel inthe tank. Fill the fuel tank to thebottom of the filler tube as shownin the illustration.
EW000130
w
Do not overfill the fuel tank. Avoid
spilling fuel on the hot engine. Do
not fill the fuel tank above the bot-
tom of the filler tube or it may
overflow when the fuel heats up
later and expands.
1. Filler tube2. Fuel level
EAU00185
cC
Always wipe off spilled fuel imme-
diately with a dry and clean soft
cloth. Fuel may deteriorate painted
surfaces or plastic parts.
EAU00191
NOTE:
If knocking or pinging occurs, use adifferent brand of gasoline or high-er octane grade.
Recommended fuel:Regular unleaded gasoline with a research octane number of 91 or higher.
Fuel tank capacity:Total:
7.0 LReserve:
1.0 L
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 16
Downloaded from www.Manualslib.com manuals search engine
3-7
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU01121
Fuel cockThe fuel cock supplies fuel fromthe tank to the carburetor while fil-tering it also.The fuel cock has three positions:
OFF
With the lever in this position, fuelwill not flow. Always return thelever to this position when theengine is not running.
1. Arrow mark positioned over “OFF”
ON
With the lever in this position, fuelflows to the carburetor. Normalriding is done with the lever in thisposition.
1. Arrow mark positioned over “ON”
RES
This indicates reserve. If you runout of fuel while riding, move thelever to this position. Fill the tankat the first opportunity. Be sure toset the fuel cock back to “ON” afterrefueling!
1. Arrow mark positioned over “RES”
RES
ONFUEL
OFF
1
Off position
OFF
ONFUEL
RES
1
RESReserve position
ONFUEL
RES
OFF
1ON
Normal position
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 17
Downloaded from www.Manualslib.com manuals search engine
3-8
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU02976
Starter (choke) “1”Starting a cold engine requires aricher air-fuel mixture. A separatestarter circuit supplies this mixture.Move in direction a to turn on thestarter (choke).Move in direction b to turn off thestarter (choke).
1. Starter (choke) “1”
EAU02934
Steering lockTo lock the steering
Turn the handlebars all the way tothe right and open the steeringlock cover.Insert the key and turn it 1/8 turncounterclockwise. Then, push thekey in while turning the handlebarsslightly to the left and turn the key1/8 turn clockwise.Check that the steering is locked,remove the key and close the lockcover.
1. Steering lock2. Cover
To unlock the steering
Insert the key, push it in and turn it1/8 turn counterclockwise so that itmoves out. Then, release andremove the key.
a
b
1
1
2
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 18
Downloaded from www.Manualslib.com manuals search engine
3-9
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU01092
SeatTo remove the seat, remove thebolts.
1. Bolt (×2)
To install the seat, insert the pro-jection on the front of the seat intothe holder and push down on theseat, then tighten the bolts.
NOTE:
Make sure that the seat is securelyfitted.
1. Projection2. Seat holder
EAU00260
Helmet holderTo open the helmet holder, insertthe key in the lock and turn it asshown. To lock the helmet holder,replace the holder in its originalposition.
EW000030
w
Never ride with a helmet in the
helmet holder. The helmet may hit
objects, causing loss of control
and possibly an accident.
1. Helmet holder
1
1
12
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 19
Downloaded from www.Manualslib.com manuals search engine
3-10
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU01343
Rear shock absorberEAU00315
w
This shock absorber contains high-
ly pressurized nitrogen gas. Read
and understand the following
information before handling the
shock absorber. The manufacturer
cannot be held responsible for
property damage or personal
injury that may result from
improper handling.
8 Do not tamper with or
attempt to open the cylinder
assembly.
8 Do not subject the shock
absorber to an open flame or
other high heat source. This
may cause the unit to explode
due to excessive gas pressure.
8 Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.
8 Take your shock absorber to a
Yamaha dealer for any service.
EAU00320
Rear carrierEW000032
w
Do not exceed the load limit of
3 kg.
1. Rear carrier
EAU01493
Luggage strap holdersThere are four luggage strap hold-ers below the rear carrier.
1. Luggage strap (×4)
1 1
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 20
Downloaded from www.Manualslib.com manuals search engine
3-11
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU00330
SidestandThis model is equipped with anignition circuit cut-off system. Themotorcycle must not be riddenwhen the sidestand is down. Thesidestand is located on the left sideof the frame. (Refer to page 5-1 foran explanation of this system.)
EW000044
w
This motorcycle must not be oper-
ated with the sidestand in the
down position. If the stand is not
properly retracted, it could contact
the ground and distract the opera-
tor, resulting in a possible loss of
control. Yamaha has designed into
this motorcycle a lockout system
to assist the operator in fulfilling
the responsibility of retracting the
sidestand. Please check carefully
the operating instructions listed
below and if there is any indication
of a malfunction, return the motor-
cycle to a Yamaha dealer immedi-
ately for repair.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 21
Downloaded from www.Manualslib.com manuals search engine
3-12
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
EAU00331
Sidestand/clutch switch operation checkCheck the operation of the side-stand switch and clutch switchagainst the information below.
EW000045
w
If improper operation is noted,
consult a Yamaha dealer immedi-
ately.
SIDESTAND IS DOWN.
ENGINE WILL STALL.
SIDESTAND SWITCH IS OK.
TURN THE MAIN SWITCH TO “ON”
AND THE ENGINE STOP SWITCH TO
“#”.
TRANSMISSION IS IN GEAR AND
SIDESTAND IS UP.
PULL IN CLUTCH LEVER AND
PUSH THE START SWITCH.
ENGINE WILL START.
CLUTCH SWITCH IS OK.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 22
Downloaded from www.Manualslib.com manuals search engine
4-1
EAU01114
PRE-OPERATION CHECKS
1
2
3
4
5
6
7
8
9
Owners are personally responsible for their vehicle’s condition. Your motorcycle’s vital functions can start todeteriorate quickly and unexpectedly, even if it remains unused (for instance, if it is exposed to the elements).Any damage, fluid leak or loss of tire pressure could have serious consequences. Therefore, it is very importantthat, in addition to a thorough visual inspection, you check the following points before each ride.
EAU00340
PRE-OPERATION CHECK LIST
ITEM CHECKS PAGE
Front brake9 Check operation, free play, fluid level and vehicle for fluid leakage. 3-4, 6-19 ~ 6-20, 6-22 ~ 6-239 Fill with DOT 4 (or DOT 3) brake fluid if necessary.
Rear brake9 Check operation, condition and free play. 3-5, 6-20 ~ 6-229 Adjust if necessary.
Clutch9 Check operation, condition and free play. 3-4, 6-199 Adjust if necessary.
Throttle grip and housing9 Check for smooth operation. 6-15, 6-269 Lubricate if necessary.
Engine oil9 Check oil level. 6-9 ~ 6-129 Fill with oil if necessary.
Drive chain9 Check chain slack and condition. 6-24 ~ 6-259 Adjust if necessary.
Wheels and tires9 Check tire pressure, wear, damage and spoke tightness. 6-16 ~ 6-189 Tighten spokes if necessary.
Brake and shift pedal shafts9 Check for smooth operation. 6-279 Lubricate if necessary.
Brake and clutch lever pivots9 Check for smooth operation. 6-279 Lubricate if necessary.
Sidestand pivot9 Check for smooth operation. 6-279 Lubricate if necessary.
Chassis fasteners9 Make sure that all nuts, bolts and screws are properly tightened. —9 Tighten if necessary.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 23
Downloaded from www.Manualslib.com manuals search engine
4-2
PRE-OPERATION CHECKS
1
2
3
4
5
6
7
8
9
NOTE:
Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accom-plished in a very short time; and the added safety it assures is more than worth the time involved.
w
If any item in the PRE-OPERATION CHECKS is not working properly, have it inspected and repaired before oper-
ating the motorcycle.
ITEM CHECKS PAGE
Fuel tank9 Check fuel level. 3-5 ~ 3-79 Fill with fuel if necessary.
Lights, signals and9 Check for proper operation. 6-32 ~ 6-34
switches
Battery9 Check fluid level. 6-30 ~ 6-319 Fill with distilled water if necessary.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 24
Downloaded from www.Manualslib.com manuals search engine
5-1
EAU00372
OPERATION AND IMPORTANT RIDING POINTS
1
2
3
4
5
6
7
8
9
EAU00373
w
8 Before riding this motorcycle,
become thoroughly familiar
with all operating controls and
their functions. Consult a
Yamaha dealer regarding any
control or function that you do
not thoroughly understand.
8 Never start your engine or let
it run for any length of time in
a closed area. The exhaust
fumes are poisonous and can
cause loss of consciousness
and death within a short time.
Always operate your motorcy-
cle in an area with adequate
ventilation.
8 Before starting out, always be
sure the sidestand is up.
Failure to retract the sidestand
completely can result in a seri-
ous accident when you try to
turn a corner.
EAU03011
Starting the engine
NOTE:
This motorcycle is equipped withan ignition circuit cut-off system.The engine can be started onlyunder one of the following condi-tions:8 The transmission is in neutral.8 The sidestand is up, the trans-
mission is in gear and theclutch is disengaged.
The motorcycle must not be riddenwhen the sidestand is down.
EW000054
w
Before going through the follow-
ing steps, check the function of the
sidestand switch and clutch
switch. (Refer to page 3-12.)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 25
Downloaded from www.Manualslib.com manuals search engine
5-2
OPERATION AND IMPORTANT RIDING POINTS
1
2
3
4
5
6
7
8
9
IF THE TRANSMISSION IS IN NEUTRAL ANDTHE SIDESTAND IS DOWN, PUSH STARTSWITCH.
THE ENGINE WILL START.
RETRACT THE SIDESTAND AND PUT THETRANSMISSION IN GEAR.
THE MOTORCYCLE CAN BE RIDDEN.THE MOTORCYCLE CAN BE RIDDEN.
IF THE TRANSMISSION IS IN GEAR AND THESIDESTAND IS UP, PULL IN THE CLUTCHLEVER AND PUSH THE START SWITCH.
TURN THE MAIN SWITCH TO “ON” ANDTHE ENGINE STOP SWITCH TO “#”.
THE ENGINE WILL START.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 26
Downloaded from www.Manualslib.com manuals search engine
5-3
OPERATION AND IMPORTANT RIDING POINTS
1
2
3
4
5
6
7
8
9
1. Turn the fuel cock to “ON”.2. Turn the main switch to “ON”
and the engine stop switch to“#”.
3. Shift the transmission intoneutral.
NOTE:
When the transmission is in neu-tral, the neutral indicator lightshould be on. If the light does notcome on, ask a Yamaha dealer toinspect it.
4. Turn on the starter (choke) andcompletely close the throttlegrip.
5. Start the engine by pushingthe start switch.
NOTE:
If the engine fails to start, releasethe start switch, wait a few sec-onds, then try again. Each attemptshould be as short as possible topreserve the battery. Do not crankthe engine more than 10 secondson any one attempt.
6. After starting the engine, movethe starter (choke) to thehalfway position.
NOTE:
For maximum engine life, neveraccelerate hard with a cold engine!
7. After warming up the engine,turn off the starter (choke)completely.
NOTE:
The engine is warm when itresponds normally to the throttlewith the starter (choke) turned off.
ONFUEL
RES
OFF
ON
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 27
Downloaded from www.Manualslib.com manuals search engine
5-4
OPERATION AND IMPORTANT RIDING POINTS
1
2
3
4
5
6
7
8
9
EAU01258
Starting a warm engineThe starter (choke) is not requiredwhen the engine is warm.
EC000046
cC
See the “Engine break-in” section
prior to operating the motorcycle
for the first time.
EC000048
cC
8 Do not coast for long periods
with the engine off, and do
not tow the motorcycle a long
distance. Even with gears in
neutral, the transmission is
only properly lubricated when
the engine is running.
Inadequate lubrication may
damage the transmission.
8 Always use the clutch when
changing gears. The engine,
transmission, and driveline are
not designed to withstand the
shock of forced shifting and
can be damaged by shifting
without using the clutch.
1
N
5432
1
EAU00423
ShiftingThe transmission lets you controlthe amount of power you haveavailable at a given speed for start-ing, accelerating, climbing hills,etc. The use of the shift pedal isshown in the illustration.
To shift into neutral, depress theshift pedal repeatedly until it reach-es the end of its travel, then raisethe pedal slightly.
1. Shift pedalN. Neutral
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 28
Downloaded from www.Manualslib.com manuals search engine
5-5
OPERATION AND IMPORTANT RIDING POINTS
1
2
3
4
5
6
7
8
9
EAU00424
Tips for reducing fuel consumptionYour motorcycle’s fuel consump-tion depends to a large extent onyour riding style. The followingtips can help reduce fuel consump-tion:8 Warm up the engine before
riding.8 Turn off the starter (choke) as
soon as possible.8 Shift up swiftly and avoid high
engine speeds during accelera-tion.
8 Do not double-clutch or rev theengine while shifting downand avoid high engine speedswith no load on the engine.
8 Turn off the engine instead ofletting it idle for an extendedlength of time, i.e. in trafficjams, at traffic lights or rail-road crossings.
EAU01128
Engine break-inThere is never a more importantperiod in the life of your motorcy-cle than the period between zeroand 1,600 km. For this reason weask that you carefully read the fol-lowing material. Because theengine is brand new, you must notput an excessive load on it for thefirst 1,600 km. The various parts inthe engine wear and polish them-selves to the correct operatingclearances. During this period, pro-longed full throttle operation, orany condition which might result inexcessive heating of the engine,must be avoided.
EAU01500
0 ~ 1,000 km
Avoid operation above 1/3 throttle.
1,000 ~ 1,600 km
Avoid cruising speeds in excess of1/2 throttle.
EC000057
cC
After 1,000 km of operation, be
sure to replace the engine oil and
clean the oil filter element and oil
strainer.
1,600 km and beyond
Proceed with normal riding.EC000049
cC
If any engine trouble should occur
during the break-in period, consult
a Yamaha dealer immediately.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 29
Downloaded from www.Manualslib.com manuals search engine
5-6
OPERATION AND IMPORTANT RIDING POINTS
1
2
3
4
5
6
7
8
9
RES
ONFUEL
OFF
EAU00457
ParkingWhen parking the motorcycle, stopthe engine and remove the ignitionkey. Turn the fuel cock to “OFF”whenever stopping the engine.
EW000058
w
The exhaust system is hot. Park
the motorcycle in a place where
pedestrians or children are not
likely to touch the motorcycle. Do
not park the motorcycle on a slope
or soft ground; the motorcycle
may overturn.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 30
Downloaded from www.Manualslib.com manuals search engine
6-1
EAU00462
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00464
Periodic inspection, adjustmentand lubrication will keep yourmotorcycle in the safest and mostefficient condition possible. Safetyis an obligation of the motorcycleowner. The maintenance and lubri-cation schedule chart should beconsidered strictly as a guide togeneral maintenance and lubrica-tion intervals. YOU MUST TAKEINTO CONSIDERATION THATWEATHER, TERRAIN, GEOGRAPHI-CAL LOCATIONS, AND A VARIETYOF INDIVIDUAL USES ALL TENDTO DEMAND THAT EACH OWNERALTER THIS TIME SCHEDULE TOSHORTER INTERVALS TO MATCHTHE ENVIRONMENT. The mostimportant points of motorcycleinspection, adjustment, and lubri-cation are explained in the follow-ing pages.
EW000060
w
If you are not familiar with motor-
cycle service, this work should be
done by a Yamaha dealer.
1
EAU01175
Tool kitThe tool kit is located behind panelB. (See page 6-7 for panel removaland installation procedures.) Thetools provided in the owner’s tool kitare to assist you in the performanceof periodic maintenance. However,some other tools such as a torquewrench are also necessary to per-form the maintenance correctly.The service information included inthis manual is intended to provideyou, the owner, with the necessaryinformation for completing some ofyour own preventive maintenanceand minor repairs.
1. Tool kit
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 31
Downloaded from www.Manualslib.com manuals search engine
6-2
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
NOTE:
If you do not have necessary toolsrequired during a service opera-tion, take your motorcycle to aYamaha dealer for service.
EW000063
w
Modifications to this motorcycle
not approved by Yamaha may
cause loss of performance, and
render it unsafe for use. Consult a
Yamaha dealer before attempting
any changes.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 32
Downloaded from www.Manualslib.com manuals search engine
6-3
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00473
PERIODIC MAINTENANCE AND LUBRICATION
Every Every6,000 km 12,000 km
No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL or or
1,000 km 6 months 12 months(Whichever (Whichevercomes first) comes first)
1 * Fuel line 9 Check fuel hoses for cracks or damage. √ √9 Replace if necessary.
2 Spark plug9 Check condition. √ √ √9 Clean, regap or replace if necessary.
3 * Valves 9 Check valve clearance. √ √ √9 Adjust if necessary.
4 Air filter 9 Clean or replace if necessary. √ √9 Check electrolyte level and specific gravity.
5 * Battery 9 Correct or recharge if necessary. √ √9Make sure that the breather hose is properly routed.
6 Clutch9 Check operation. √ √ √9 Adjust or replace cable.
9 Check operation, fluid level and vehicle for fluid leakage.
7 * Front brake (See NOTE on page 6-5.) √ √ √9 Correct accordingly.9 Replace brake pads if necessary.
8 * Rear brake 9 Check operation. √ √ √9 Adjust brake pedal freeplay and replace brake shoes if necessary.
9 * Wheels 9 Check balance, runout, spoke tightness and for damage. √ √9 Tighten spokes and rebalance, replace if necessary.
9 Check tread depth and for damage.
10 * Tires9 Replace if necessary. √ √9 Check air pressure.9 Correct if necessary.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 33
Downloaded from www.Manualslib.com manuals search engine
6-4
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
Every Every6,000 km 12,000 km
No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL or or
1,000 km 6 months 12 months(Whichever (Whichevercomes first) comes first)
11 * Wheel bearings9 Check bearing for looseness or damage. √ √9 Replace if necessary.
9 Check swingarm pivoting point for play.12 * Swingarm 9 Correct if necessary. √ √
9 Lubricate with lithium soap base grease.
9 Check chain slack. Every 500 km and after washing13 Drive chain 9 Adjust if necessary. Make sure that the rear wheel is properly aligned. the motorcycle or riding in the rain
9 Clean and lubricate.
9 Check bearing play and steering for roughness.
14 * Steering bearings9 Correct accordingly. √ √9 Lubricate with lithium soap base grease every 24,000 km or
24 months (whichever comes first).
15 * Chassis fasteners9Make sure that all nuts, bolts and screws are properly tightened. √ √9 Tighten if necessary.
16 Sidestand9 Check operation. √ √9 Lubricate and repair if necessary.
17 * Sidestand switch9 Check operation. √ √ √9 Replace if necessary.
18 * Front fork9 Check operation and for oil leakage. √ √9 Correct accordingly.
19 *Rear shock absorber 9 Check operation and shock absorber for oil leakage. √ √assembly 9 Replace shock absorber assembly if necessary.
Rear shock absorber 9 Check operation. 20 assembly pivoting 9 Lubricate with lithium soap base grease every 24,000 km or √ √
points 24 months (whichever comes first).
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 34
Downloaded from www.Manualslib.com manuals search engine
6-5
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
*: Since these items require special tools, data and technical skills, they should be serviced by a Yamaha dealer.
EAU02970
NOTE:
8 The air filter needs more frequent service if you are riding in unusually wet or dusty areas.8 Hydraulic brake system8 When disassembling the master cylinder or caliper, always replace the brake fluid. Check the brake fluid
level regularly and fill as required.8 Replace the oil seals on the inner parts of the master cylinder and caliper every two years.8 Replace the brake hoses every four years or if cracked or damaged.
Every Every6,000 km 12,000 km
No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL or or
1,000 km 6 months 12 months(Whichever (Whichevercomes first) comes first)
21 * Carburetor9 Check engine idling speed and starter operation. √ √ √9 Adjust if necessary.
9 Check oil level and vehicle for oil leakage. 22 Engine oil 9 Correct if necessary. √ √ √
9 Change. (Warm engine before draining.)
23 Engine oil filter element 9 Clean or replace if necessary. √ √24 * Engine oil strainer 9 Clean or replace if necessary. √ √
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 35
Downloaded from www.Manualslib.com manuals search engine
6-6
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01139
Cowling and panel removal and installationThe cowlings and panels illustratedneed to be removed to performsome of the maintenancedescribed in this chapter.Refer to this section each time acowling or panel has to beremoved or reinstalled.
1. Panel B 1. Panel A2. Cowling C
EAU01492
Panel ATo remove
Remove the screws and pull out-ward on the area shown.
1. Panel A2. Screw (×2)
1
2
1
21
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 36
Downloaded from www.Manualslib.com manuals search engine
6-7
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
To install
Place the panel in the original posi-tion and install the screws.
EAU00494
Panel BTo remove
Pull outward on the areas shown.
1. Panel B
To install
Place the panel in its original posi-tion.
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 37
Downloaded from www.Manualslib.com manuals search engine
6-8
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01833
Spark plugRemoval
1. Remove the spark plug cap.2. Use the spark plug wrench in
the tool kit to remove the sparkplug as shown.
1. Spark plug wrench
Inspection
The spark plug is an importantengine component and is easy toinspect. The condition of the sparkplug can indicate the condition ofthe engine.The ideal color on the white insula-tor around the center electrode is amedium-to-light tan color for amotorcycle that is being riddennormally.Do not attempt to diagnose suchproblems yourself. Instead, takethe motorcycle to a Yamaha deal-er. You should periodically removeand inspect the spark plug becauseheat and deposits will cause anyspark plug to slowly break downand erode. If electrode erosionbecomes excessive, or if carbonand other deposits are excessive,you should replace the spark plugwith the specified plug.
Specified spark plug:DR8EA (NGK)
12
1
EAU01145
Cowling CTo remove
Remove the cowling screw andpull outward on the areas shown.
To install
Place in the original position andinstall the screw.
1. Cowling C2. Screw
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 38
Downloaded from www.Manualslib.com manuals search engine
6-9
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
Installation
1. Measure the electrode gapwith a wire thickness gaugeand, if necessary, adjust thegap to specification.
2. Clean the gasket surface. Wipeoff any grime from thethreads.
3. Install the spark plug and tight-en it to the specified torque.
1. Spark plug gap
NOTE:
If a torque wrench is not availablewhen you are installing a sparkplug, a good estimate of the cor-rect torque is 1/4 to 1/2 turn pastfinger tight. Have the spark plugtightened to the specified torque assoon as possible.
4. Install the spark plug cap.
EAU00517*
Engine oilOil level measurement
1. Place the motorcycle on a levelplace and hold it in an uprightposition. Warm up the enginefor several minutes.
NOTE:
Be sure the motorcycle is posi-tioned straight up when checkingthe oil level. A slight tilt toward theside can result in false readings.
Spark plug gap:0.6 ~ 0.7 mm
Tightening torque:Spark plug:
17.5 Nm (1.75 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 39
Downloaded from www.Manualslib.com manuals search engine
6-10
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
2. With the engine stopped,check the oil level through thelevel window located at thelower part of the right sidecrankcase cover.
NOTE:
Wait a few minutes until the oillevel settles before checking.
3. The oil level should bebetween the maximum andminimum marks. If the level islow, add sufficient oil to raiseit to the proper level.
1. Maximum level mark2. Minimum level mark
Engine oil replacement
1. Warm up the engine for a fewminutes.
2. Stop the engine. Place an oilpan under the engine andremove the oil filler cap.
1. Engine oil filler cap
3. Remove the drain bolts.
1. Engine oil drain bolt
1
1
12
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 40
Downloaded from www.Manualslib.com manuals search engine
6-11
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EC000070
cC
When removing the oil drain bolt,
the O-ring, compression spring,
and oil strainer will fall out. Take
care not to lose these parts.
1. Strainer2. Compression spring3. O-ring
NOTE:
The oil filter cover is secured bytwo screws and a drain bolt.Remove the drain bolt to drain thefilter cavity.
1. Bolts (×3)2. Engine oil drain bolt
4. Remove the filter cover screwsand the oil filter cover.
5. Remove the oil filter elementand O-ring.
6. Clean the oil filter and strainerwith solvent. Replace if neces-sary.
7. Check the O-rings. If damaged,replace.
8. Install the filter cover, screwsand drain bolts. Tighten thedrain bolts to the specifiedtightening torques.
NOTE:
Make sure the O-ring is seatedproperly.
1. Oil filter element2. O-ring
1 2 3
1
2
12
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 41
Downloaded from www.Manualslib.com manuals search engine
6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
2 2
EAU01501*
Air filterThe air filter should be cleaned atthe specified intervals. It should becleaned more frequently when rid-ing in unusually wet or dustyareas.
Air filter element cleaning
1. Remove panel A. (See page6-6 for removal and installa-tion procedures.)
2. Remove the air filter case fit-ting screws and the filter casecover.
1. Air filter case cover2. Screw (×4)
EC000066
cC
8 Do not put in any chemical
additives. Engine oil also lubri-
cates the clutch and additives
could cause clutch slippage.
8 Be sure no foreign material
enters the crankcase.
10. Start the engine and warm upfor a few minutes. Whilewarming up, check for oil leak-age. If oil leakage is found,stop the engine immediatelyand check for the cause.
EC000071
cC
Before reinstalling the oil drain
bolt, do not forget to install the O-
ring, compression spring, and oil
strainer in position.
9. Fill the engine with oil. Installthe oil filler cap and tighten.
Tightening torque:Drain bolt:
43 Nm (4.3 m·kg)Filter cover screw:
7.0 Nm (0.7 m·kg)Drain bolt (filter cover):
10 Nm (1.0 m·kg)
Recommended oil:See page 8-1.
Total amount:1.3 L
Periodic oil change:1.0 L
With oil filter replacement:1.1 L
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 42
Downloaded from www.Manualslib.com manuals search engine
6-13
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
3. Remove the air filter from thecase.
4. Remove the air filter elementfrom its frame and clean itwith solvent. After cleaning,remove the remaining solventby squeezing the element.
5. Apply recommended oil to theentire surface of the elementand squeeze out the excess oil.The element should be wet butnot dripping.
1. Air filter element2. Air filter element frame
6. Install the air filter frame ontothe air filter and install theassembly in the case.
7. Install the air filter case coverand panel.
EC000082
cC
8 Make sure the air filter is prop-
erly seated in the air filter
case.
8 The engine should never be
run without the air filter
installed. Excessive piston
and/or cylinder wear may
result.
Air filter case drain hose cleaning
Frequently check the hose at thebottom of the air filter case. If dirtor water is visible, remove andclean the hose, then reinstall it.
1. Hose
Recommended oil:Engine oil
12
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 43
Downloaded from www.Manualslib.com manuals search engine
6-14
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00629
Carburetor adjustmentThe carburetor is a vital part of theengine and requires very sophisti-cated adjustment. Most adjust-ments should be left to a Yamahadealer who has the professionalknowledge and experience to doso. However, the following may beserviced by the owner as part ofroutine maintenance.
EC000094
cC
The carburetor was set at the
Yamaha factory after many tests. If
the settings are changed, poor
engine performance and damage
may result.
EAU01168
Idle speed adjustment
NOTE:
A diagnostic tachometer must beused for this procedure.
1. Attach the tachometer. Startthe engine and warm it up fora few minutes at approximate-ly 1,000 to 2,000 r/min.Occasionally rev the engine to4,000 to 5,000 r/min. Theengine is warm when it quicklyresponds to the throttle.
2. Set the idle to the specifiedengine speed by adjusting thethrottle stop screw. Turn thescrew in direction a toincrease engine speed and indirection b to decrease enginespeed.
NOTE:
If the specified idle speed cannotbe obtained by performing theabove adjustment, consult aYamaha dealer.
1. Throttle stop screw
1
ab
Standard idle speed:1,300 ~ 1,500 r/min
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 44
Downloaded from www.Manualslib.com manuals search engine
6-15
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00634
Throttle cable free play adjustment
NOTE:
Before checking the throttle cablefree play, the engine idling speedshould be adjusted.
Adjust the throttle cable by turningthe adjusting nut so that specifiedfree play at the throttle grip isobtained.
1. Adjusting nut2. Locknutc. Free play
1. Loosen the locknut.2. Turn the adjusting nut in direc-
tion a to increase free playand in direction b to decreasefree play.
3. Tighten the locknut.
EAU00637
Valve clearance adjustmentThe correct valve clearancechanges with use, resulting inimproper fuel/air supply or enginenoise. To prevent this, the valveclearance must be adjusted regu-larly. This adjustment however,should be left to a professionalYamaha service technician.
1 2a
b
c
Free play:3 ~ 5 mm
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 45
Downloaded from www.Manualslib.com manuals search engine
6-16
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00652
TiresTo ensure maximum performance,long service and safe operation,note the following:
Tire air pressure
Always check and adjust the tirepressure before operating themotorcycle.
EW000082
w
Tire inflation pressure should be
checked and adjusted when the
temperature of the tire equals the
ambient air temperature. Tire infla-
tion pressure must be adjusted
according to total weight of cargo,
rider, passenger, and accessories
(fairing, saddlebags, etc. if
approved for this model), and vehi-
cle speed.
EW000083
w
Proper loading of your motorcycle
is important for several character-
istics of your motorcycle, such as
handling, braking, performance
and safety. Do not carry loosely
packed items that can shift.
Securely pack your heaviest items
close to the center of the motorcy-
cle, and distribute the weight
evenly from side to side. Properly
adjust the suspension for your
load, and check the condition and
pressure of your tires. NEVER
OVERLOAD YOUR MOTORCYCLE.
Make sure the total weight of the
cargo, rider, passenger, and acces-
sories (fairing, saddlebags, etc. if
approved for this model) does not
exceed the maximum load of the
motorcycle. Operation of an over-
loaded motorcycle could cause tire
damage, an accident, or even
injury.
* Load is the total weight of cargo, rider, passen-ger and accessories.
Maximum load* 180 kg
Cold tire pressure Front Rear
150 kPa 150 kPaUp to 80 kg (1.50 kg/cm2, (1.50 kg/cm2,
1.50 bar) 1.50 bar)
80 kg load -150 kPa 175 kPa
Maximum load*(1.50 kg/cm2, (1.75 kg/cm2,
1.50 bar) 1.75 bar)
125 kPa 125 kPaOff-road riding (1.25 kg/cm2, (1.25 kg/cm2,
1.25 bar) 1.25 bar)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 46
Downloaded from www.Manualslib.com manuals search engine
6-17
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
2
Tire inspection
Always check the tires before oper-ating the motorcycle. If centertread depth reaches the limit asshown, if the tire has a nail or glassfragments in it, or if the side wall iscracked, contact a Yamaha dealerimmediately and have the tirereplaced.
1. Tread depth2. Side wall
EW000078
w
After extensive tests, the tires
mentioned below have been
approved by Yamaha Motor Co.,
Ltd. for this model. No guarantee
for handling characteristics can be
given if tire combinations other
than what is approved are used on
this motorcycle. The front and rear
tires should be of the same manu-
facture and design.
NOTE:
These limits may be different byregulation from country to country.If so, conform to the limits speci-fied by the regulations of your owncountry.
Manufacture Size Type
BRIDGESTONE 130/80-18 66P TW31
Manufacture Size Type
BRIDGESTONE 180/80-14M/C 78P TW34
REAR
Minimum tire tread depth (front and rear)
1.6 mm
FRONT
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 47
Downloaded from www.Manualslib.com manuals search engine
6-18
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00681
w
8 Operating the motorcycle with
excessively worn tires
decrease riding stability and
can lead to loss of control.
Have excessively worn tires
replaced by a Yamaha dealer
immediately. Brakes, tires, and
related wheel parts replace-
ment should be left to a
Yamaha Service Technician.
8 Patching a punctured tube is
not recommended. If it is
absolutely necessary to do so,
use great care and replace the
tube as soon as possible with
a good quality replacement.
EAU00685
WheelsTo ensure maximum performance,long service, and safe operation,note the following:8 Always inspect the wheels
before a ride. Check for cracks,bends or warpage of thewheel. Be sure the spokes aretight and undamaged. If anyabnormal condition exists in awheel, consult a Yamaha deal-er. Do not attempt even smallrepairs to the wheel. If a wheelis deformed or cracked, it mustbe replaced.
8 Tires and wheels should bebalanced whenever either oneis changed or replaced. Failureto have a wheel balanced canresult in poor performance,adverse handling characteris-tics, and shortened tire life.
8 Ride at moderate speeds afterchanging a tire since the tiresurface must first be broken infor it to develop its optimalcharacteristics.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 48
Downloaded from www.Manualslib.com manuals search engine
6-19
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
If the specified free play cannot beobtained, proceed with the follow-ing steps.
4. Loosen the locknut at theclutch lever.
5. Turn the adjusting bolt at theclutch lever in direction a toloosen the cable.
6. Loosen the locknut at thecrankcase side.
7. Turn the adjusting nut at thecrankcase in direction a toincrease free play or in direc-tion b to decrease free play.
8. Tighten the locknut at thecrankcase and the clutch lever.
1. Locknut2. Adjusting nut
EAU00694
Clutch lever free play adjustmentThe clutch lever free play shouldbe adjusted to 10 ~ 15 mm.
1. Loosen the locknut at theclutch lever.
2. Turn the adjusting bolt at theclutch lever in direction a toincrease free play or in direc-tion b to decrease free play.
3. Tighten the locknut at theclutch lever.
1. Locknut 2. Adjusting boltc. Free play
EAU00696
Front brake lever free playadjustmentThe free play at the front brakelever should be 2 ~ 5 mm.
1. Loosen the locknut.2. Turn the adjusting bolt in
direction a to increase freeplay or in direction b todecrease free play.
3. After adjusting, tighten thelocknut.
1. Locknut2. Adjusting boltc. Free play
c
1
2
a
b
1a
b
2
1 2 c
a
b
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 49
Downloaded from www.Manualslib.com manuals search engine
6-20
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
d
c
21
a
b
EAU00707
Rear brake pedal height and free play adjustment
EW000104
w
It is advisable to have a Yamaha
dealer make this adjustment.
Pedal height
The brake pedal should be posi-tioned so that its top end isapproximately 15 mm below thetop of the footrest.
1. Loosen the locknut.
1. Locknut2. Adjusting boltc. Pedal heightd. Free play
EW000099
w
8 Check the brake lever free
play. Be sure the brake is
working properly.
8 A soft or spongy feeling in the
brake lever can indicate the
presence of air in the brake
system. This air must be
removed by bleeding the
brake system before the
motorcycle is operated. Air in
the system will cause greatly
diminished braking capability
and can result in loss of con-
trol and an accident. Have a
Yamaha dealer inspect and
bleed the system if necessary.
2. Turn the adjusting bolt indirection a to raise pedalheight or in direction b tolower pedal height.
3. Tighten the locknut.EW000105
w
After adjusting the pedal height
adjust brake pedal free play.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 50
Downloaded from www.Manualslib.com manuals search engine
6-21
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
b
a
Free play
The rear brake pedal free playshould be adjusted to 20 ~ 30 mmat the brake pedal end. Turn theadjusting nut on the brake rod indirection a to increase free play orin direction b to decrease freeplay.
1. Adjusting nut
EW000106
w
8 Brake pedal free play should
be checked whenever the
chain is adjusted or the rear
wheel is removed and then
reinstalled.
8 Check the operation of the
brake light after adjusting the
rear brake.
8 If it is impossible to make
proper adjustment, consult a
Yamaha dealer.
1
2a
b
EAU00713
Brake light switch adjustmentThe rear brake light switch is acti-vated by the brake pedal and isproperly adjusted when the brakelight comes on just before brakingtakes effect. To adjust the rearbrake light switch, hold the switchbody so it does not rotate whileturning the adjusting nut.Turn the adjusting nut in directiona to make the brake light come onearlier.Turn the adjusting nut in directionb to make the brake light come onlater.
1. Brake light switch2. Adjusting nut
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 51
Downloaded from www.Manualslib.com manuals search engine
6-22
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00720
Checking the front brake pads and rear brake shoes
EAU01119
Front brake
Wear indicator grooves are provid-ed on each brake pad. These indi-cators allow checking of brake padwear without disassembling thebrake. Inspect the grooves. If theyhave almost disappeared, ask aYamaha dealer to replace the pads.
1. Indicator grooves
EAU00727
Rear brake
Apply the brake and inspect thewear indicator.If the indicator reaches the wearlimit line, ask a Yamaha dealer toreplace the shoes.
1. Wear limit line2. Wear indicator
EAU00732
Inspecting the brake fluid levelInsufficient brake fluid may let airenter the brake system, possiblycausing the brakes to become inef-fective.Before riding, check that the brakefluid is above the minimum leveland fill when necessary.Observe these precautions:8 When checking the fluid level,
make sure the top of the mas-ter cylinder is level by turningthe handlebars.
1. Minimum level mark
1
FRONT
2
1REAR
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 52
Downloaded from www.Manualslib.com manuals search engine
6-23
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
8 Use only the designated quali-ty brake fluid. Otherwise, therubber seals may deteriorate,causing leakage and poorbrake performance.
NOTE:
If DOT 4 is not available, DOT 3 canbe used.
8 Refill with the same type ofbrake fluid. Mixing fluids mayresult in a harmful chemicalreaction and lead to poorbrake performance.
8 Be careful that water does notenter the master cylinder whenrefilling. Water will significant-ly lower the boiling point ofthe fluid and may result invapor lock.
8 Brake fluid may deterioratepainted surfaces or plasticparts. Always clean up spilledfluid immediately.
8 Have a Yamaha dealer checkthe cause if the brake fluidlevel goes down.
EAU00742
Brake fluid replacementThe brake fluid should be replacedonly by trained Yamaha servicepersonnel. Have the Yamaha deal-er replace the following compo-nents during periodic maintenanceor when they are damaged or leak-ing:8 oil seals (every two years)8 brake hoses (every four years)
Recommended brake fluid: DOT 4
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 53
Downloaded from www.Manualslib.com manuals search engine
6-24
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00744
Drive chain slack check
NOTE:
Spin the wheel several times andfind the tightest position of thechain. Check and/or adjust thechain slack while it’s in this tightestposition.
a. Chain slack
To check the chain slack the motor-cycle must be held straight up withboth wheels on the ground andwithout rider. Check the slack atthe position shown in the illustra-tion. Normal slack is approximately35 ~ 60 mm. If the slack exceeds 60 mm, adjust.
EAU01533
Drive chain slack adjustment1. Loosen the rear brake adjust-
ing nut.2. Loosen the wheel axle nut.3. To tighten the chain, turn the
chain adjusting plates in direc-tion a. To loosen the chain,turn the chain adjusting platesin direction b and push thewheel forward. Turn eachchain adjusting plate to exactlythe same position to maintaincorrect axle alignment.
1. Wheel axle nut2. Chain adjusting plate3. Rear brake adjusting nut
a 2
1
a
b
3
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 54
Downloaded from www.Manualslib.com manuals search engine
6-25
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EC000096
cC
Too little chain slack will overload
the engine and other vital parts.
Keep the slack within the specified
limits.
4. Tighten the wheel axle nut tothe specified torque.
5. Adjust the brake pedal freeplay.
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
EAU01106*
Drive chain lubricationThe chain consists of many partswhich work with each other. If thechain is not maintained properly, itwill wear out quickly. Therefore,the chain must be serviced regular-ly. This service is especially neces-sary when riding in dusty areas.The drive chain should be lubri-cated every 500 km. First, removeall dirt and mud from the chainwith a brush or cloth. Then, sprayany of the many brands of spray-type chain lubricant betweenboth rows of side plates and onall center rollers.To clean the chain thoroughly,remove it from the motorcycle,dip it in solvent, and clean out asmuch dirt as possible. Then, takethe chain out of the solvent todry it, and immediately lubricateit to prevent it from rusting.
EC000097
cC
Be sure to oil the chain after wash-
ing the motorcycle or riding in the
rain.
Tightening torque:Wheel axle nut:
90 Nm (9.0 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 55
Downloaded from www.Manualslib.com manuals search engine
6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU02962
Cable inspection and lubrication
EW000112
w
Damage to the outer housing of
cables may lead to internal rusting
and interfere with the cable move-
ment. Replace damaged cables as
soon as possible to prevent unsafe
conditions.
Lubricate the cables and cableends. If a cable does not operatesmoothly, ask a Yamaha dealer toreplace it.
EAU00773
Throttle cable and grip lubricationThe throttle twist grip assemblyshould be greased at the time thatthe cable is lubricated, since thegrip must be removed to get at theend of the throttle cable. Afterremoving the screws, hold the endof the cable up in the air and put inseveral drops of lubricant. With thethrottle grip disassembled, coat themetal surface of the grip assemblywith a suitable all-purpose grease.
Recommended lubricant:Engine oil
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 56
Downloaded from www.Manualslib.com manuals search engine
6-27
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU02984
Brake and shift pedal lubricationLubricate the pivoting parts.
EAU02985
Brake and clutch lever lubricationLubricate the pivoting parts.
EAU02986
Sidestand lubricationLubricate the sidestand pivotingpoint and metal-to-metal contactsurfaces. Check that the sidestandmoves up and down smoothly.
EW000113
w
If the sidestand does not move
smoothly, consult a Yamaha deal-
er.
Recommended lubricant:Engine oil
Recommended lubricant:Engine oil
Recommended lubricant:Engine oil
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 57
Downloaded from www.Manualslib.com manuals search engine
6-28
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00791
Rear suspension lubricationLubricate the pivoting parts.
1. Grease nipple (×2)
EAU02939
Front fork inspectionVisual check
EW000115
w
Securely support the motorcycle
so there is no danger of it falling
over.
Check for scratches or damage onthe inner tube and excessive oilleakage from the front fork.
Operation check
1. Place the motorcycle on a levelplace.
2. Hold the motorcycle in anupright position and apply thefront brake.
3. Push down hard on the han-dlebars several times andcheck if the fork reboundssmoothly.
EC000098
cC
If any damage or unsmooth move-
ment is found with the front fork,
consult a Yamaha dealer.
1
Recommended lubricant:Lithium soap base grease
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 58
Downloaded from www.Manualslib.com manuals search engine
6-29
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00794
Steering inspectionPeriodically inspect the conditionof the steering. Worn out or loosesteering bearings may be danger-ous. Place a stand under theengine to raise the front wheel offthe ground. Hold the lower end ofthe front forks and try to movethem forward and backward. If anyfree play can be felt, ask a Yamahadealer to inspect and adjust thesteering. Inspection is easier if thefront wheel is removed.
EW000115
w
Securely support the motorcycle
so there is no danger of it falling
over.
EAU01144
Wheel bearingsIf there is play in the front or rearwheel hub or if the wheel does notturn smoothly, have a Yamahadealer inspect the wheel bearings.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 59
Downloaded from www.Manualslib.com manuals search engine
6-30
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
EAU01071
BatteryCheck the level of the battery elec-trolyte and make sure that the ter-minals are tight.Fill with distilled water if the elec-trolyte level is low.
EC000099
cC
When inspecting the battery, be
sure the breather hose is routed
correctly. If the breather hose is
positioned in such a way as to
cause battery electrolyte or gas to
exit onto the frame, structural and
cosmetic damage to the motorcy-
cle can occur.
1. Battery
EW000116
w
Battery electrolyte is poisonous
and dangerous, causing severe
burns, etc. It contains sulfuric acid.
Avoid contact with skin, eyes or
clothing.
ANTIDOTE:
8 EXTERNAL: Flush with water.
8 INTERNAL: Drink large quanti-
ties of water or milk. Follow
with milk of magnesia, beaten
egg, or vegetable oil. Call a
physician immediately.
8 EYES: Flush with water for 15
minutes and get prompt med-
ical attention.
Batteries produce explosive gases.
Keep sparks, flame, cigarettes etc.,
away. Ventilate when charging or
using in an enclosed space.
Always shield your eyes when
working near batteries.
KEEP OUT OF REACH OF CHIL-
DREN.
12
Replenishing the battery fluid
A poorly maintained battery willcorrode and discharge quickly. Thebattery fluid should be checked atleast once a month. The levelshould be between the minimumlevel and maximum level marks.Use only distilled water if refillingis necessary.
EC000100
cC
Normal tap water contains miner-
als which are harmful to a battery;
therefore, refill only with distilled
water.
1. Maximum level mark2. Minimum level mark
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 60
Downloaded from www.Manualslib.com manuals search engine
6-31
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EW000117
w
Take care not to spill battery fluid
on the chain. Battery fluid may
weaken the chain causing shorter
chain life and possibly result in an
accident.
Battery storage
8 When the motorcycle will notbe used for a month or longer,remove the battery, fullycharge it and store it in a cool,dry place. Completely rechargethe battery before reinstalla-tion.
1. Battery breather hose
8 If the battery will be stored forlonger than two months, checkthe specific gravity of the fluidat least once a month and fullyrecharge the battery when it istoo low.
8 Always make sure the connec-tions are correct when puttingthe battery back in the motor-cycle. Make sure the breatherhose is properly connectedand is not damaged orobstructed.
1. Battery2. Battery breather hose
EAU01307
Fuse replacementThe fuse is located behind panel B.(See page 6-7 for panel removaland installation procedures.)If the fuse is blown, turn off themain switch and the switch of thecircuit in question. Install a newfuse of proper amperage. Turn onthe switches and see if the electri-cal device operates. If the fuseimmediately blows again, consult aYamaha dealer.
1. Spare fuse2. Main fuse
1
2
1
2
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 61
Downloaded from www.Manualslib.com manuals search engine
6-32
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EC000103
cC
Do not use fuses of higher amper-
age rating than those recommend-
ed. Substitution of a fuse of
improper rating can cause exten-
sive electrical system damage and
possibly a fire.
EAU01158
Headlight bulb replacementIf the headlight bulb burns out,replace the bulb as follows:
1. Remove cowling C. (See page6-8 for removal and installa-tion procedures.)
2. Remove the headlight unit byremoving the bolts.
1. Bolt (×2)
3. Remove the headlight connec-tor and the bulb holder cover.
1. Connector2. Bulb holder cover
1
1
2
Specified fuse: 20A
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 62
Downloaded from www.Manualslib.com manuals search engine
6-33
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
4. Turn the bulb holder counter-clockwise to remove it andthen remove the defectivebulb.
EW000119
w
Keep flammable products and your
hands away from a bulb while it is
on, as it is hot. Do not touch a bulb
until it cools down.
5. Put a new bulb into positionand secure it in place with thebulb holder.
1. Bulb holder
6. Install the bulb holder cover,connector and headlight unit.
7. Install the cowling.8. If the headlight beam adjust-
ment is necessary, ask aYamaha dealer to make thatadjustment.
EAU00855
Turn signal and taillight bulb replacement
1. Remove the screws and thelens.
1. Screw
1 1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 63
Downloaded from www.Manualslib.com manuals search engine
6-34
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
2. Push the bulb inward and turnit counterclockwise.
1. Screw (×2)
3. Place a new bulb in the socket.Push the bulb inward and turnit clockwise until it engagesinto the socket.
4. Install the lens and the screws.EC000108
cC
Do not over-tighten the screws as
the lens may break.
1. Bulb
EAU01579
Supporting the motorcycleSince the Yamaha TW125 has nocenterstand, follow these precau-tions when removing the front andrear wheel or performing othermaintenance requiring the motor-cycle to stand upright. Check thatthe motorcycle is in a stable andlevel position before starting anymaintenance. A strong woodenbox can be placed under theengine for added stability.
Front wheel service
To stabilize the rear of the motor-cycle, either use a motorcyclestand or place a motorcycle jackunder the frame in front of the rearwheel to prevent it from movingfrom side to side. Then use amotorcycle stand to elevate thefront wheel off of the ground.
11
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 64
Downloaded from www.Manualslib.com manuals search engine
6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
Rear wheel service
Use a motorcycle stand or motor-cycle jack to elevate the motorcycleso the rear wheel is off the ground.Alternatively, two jacks can beplaced under the frame orswingarm.
1
2
EAU01494
Front wheel removalEW000122
w
8 It is advisable to have a
Yamaha dealer service the
wheel.
8 Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Remove the speedometercable from the front wheelside.
1. Speedometer cable2. Wheel axle nut
2. Loosen the wheel axle nut.3. Elevate the front wheel by
placing a suitable stand underthe engine.
4. Remove the wheel axle nut,the wheel axle and the frontwheel. Make sure the motorcy-cle is properly supported.
NOTE:
Do not depress the brake leverwhen the disc and caliper are sepa-rated.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 65
Downloaded from www.Manualslib.com manuals search engine
6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01495
Front wheel installation1. Install the speedometer gear
unit housing into the wheelhub. Make sure the projectionsare meshed into the slots.
2. Lift up the wheel between thefront fork legs. Make sure thatthere is enough gap betweenthe brake pads before insertingthe brake disc and that the slotin the speedometer gear unithousing fits over the stopperon the front fork outer tube.
3. Install the wheel axle and axlenut. Then, let the motorcycledown.
4. Tighten the axle nut to thespecified torque.
5. Install the speedometer cable.
EAU01496
Rear wheel removalEW000122
w
8 It is advisable to have a
Yamaha dealer service the
wheel.
8 Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Loosen the wheel axle nut.2. Remove the brake adjusting
nut and brake rod from thebrake cam lever.
1. Wheel axle nut2. Chain adjusting plate3. Brake adjusting nut4. Brake rod
2
1
a
b
3 4
Tightening torque:Axle nut:
90 Nm (9.0 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 66
Downloaded from www.Manualslib.com manuals search engine
6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
3. Turn the chain adjusting plateson each side fully in directionb.
4. Elevate the rear wheel.5. Remove the axle nut.6. Pull out the rear axle.7. Push the wheel forward and
remove the drive chain.8. Remove the wheel assembly.
EAU01497
Rear wheel installation1. Install the wheel assembly and
insert the axle from the left-hand side. Be sure that thechain adjusting plates areinstalled with the punched sideoutward and the slot in thebrake shoe plate fits over thestopper on the swingarm.
2. Install and adjust the drivechain. (See page 6-24 fordetails about adjusting thedrive chain slack.)
3. Install the axle nut and let themotorcycle down.
4. Tighten the axle nut to thespecified torque.
5. Insert the brake rod into thebrake cam lever and install thebrake pedal free play adjustingnut.
6. Adjust the rear brake pedalfree play. (See page 6-20.)
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
Tightening torque:Axle nut:
90 Nm (9.0 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 67
Downloaded from www.Manualslib.com manuals search engine
6-38
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01008
TroubleshootingAlthough Yamaha motorcyclesreceive a rigid inspection beforeshipment from the factory, troublemay occur during operation.Any problem in the fuel, compres-sion, or ignition systems can causepoor starting and loss of power.The troubleshooting chartdescribes a quick, easy procedurefor making checks.If your motorcycle requires anyrepair, bring it to a Yamaha dealer.The skilled technicians at aYamaha dealership have the tools,experience, and know-how toproperly service your motorcycle.Use only genuine Yamaha parts onyour motorcycle. Imitation partsmay look like Yamaha parts, butthey are often inferior.Consequently, they have a shorterservice life and can lead to expen-sive repair bills.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 68
Downloaded from www.Manualslib.com manuals search engine
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
6-39
EAU03009
Troubleshooting chartEW000125
w
Never check the fuel system while smoking or in the vicinity of an open flame.
1. Fuel
2. Compression
3. Ignition
4. Battery
Use the electric starter.
Remove spark
There is compression. Go to ignition check.
No compression. Ask a Yamaha dealer to inspect.
Wet.
Dry.
Wipe clean with dry cloth and Open throttle half-way and start
Ask a Yamaha dealer to inspect.
Engine turns over
Engine turns over
Battery good.
Check fluid, recharge,
Use the electric starter.
Check if there is fuel
Enough fuel.
No fuel.
Go to compression check.
Supply fuel.
in the fuel tank.
electrodes.plug and check
quickly.
slowly. check connections.
Engine doesn’t start, go to batterycheck.
the engine.correct spark gap or replace plug.
Engine doesn’t start, ask a Yamahadealer to inspect.
Engine doesn’t start, go to compression check.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 69
Downloaded from www.Manualslib.com manuals search engine
7-1
EAU01518
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9
CareThe exposure of its technologymakes a motorcycle charming butalso vulnerable. Although high-quality components are used, theyare not all rust-resistant. While arusty exhaust pipe may remainunnoticed on a car, it does lookunattractive on a motorcycle.Frequent and proper care, howev-er, will keep your motorcycle look-ing good, extend its life and main-tain its performance. Moreover, thewarranty states that the vehiclemust be properly taken care of. Forall these reasons, it is recommend-ed that you observe the followingcleaning and storing precautions.
Before cleaning
1. Cover up the muffler outletwith a plastic bag.
2. Make sure that all caps andcovers as well as all electricalcouplers and connectors,including the spark plug cap,are tightly installed.
3. Remove extremely stubborndirt, like oil burnt onto thecrankcase, with a degreasingagent and a brush, but neverapply such products ontoseals, gaskets, sprockets, thedrive chain and wheel axles.Always rinse the dirt anddegreaser off with water.
Cleaning
After normal useRemove dirt with warm water, aneutral detergent and a soft cleansponge, then rinse with plenty ofclean water. Use a tooth or bottlebrush for hard-to-reach parts.Tougher dirt and insects will comeoff more easily if the area is cov-ered with a wet cloth for a fewminutes before cleaning.
ECA00010
cC
8 Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If you do use
such products for hard-to-
remove dirt, do not leave it on
any longer than instructed,
then thoroughly rinse it off
with water, immediately dry
the area and apply a corrosion
protection spray.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 70
Downloaded from www.Manualslib.com manuals search engine
7-2
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9
8 Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8 Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, solvent
or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
8 Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
8 For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
After riding in the rain, near thesea or on salt-sprayed roadsSince sea salt or salt sprayed onthe roads in the winter areextremely corrosive in combina-tion with water, carry out the fol-lowing steps after each ride in therain, near the sea or on salt-sprayed roads. (Salt sprayed in thewinter may remain on the roadswell into spring.)
1. Clean your motorcycle withcold water and soap after theengine has cooled down.
ECA00012
cC
Do not use warm water since it
increases the corrosive action of
the salt.
2. Be sure to apply a corrosionprotection spray on all (evenchrome- and nickel-plated)metal surfaces to prevent cor-rosion.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 71
Downloaded from www.Manualslib.com manuals search engine
7-3
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9
After cleaning
1. Dry the motorcycle with achamois or an absorbing cloth.
2. Immediately dry the drivechain and lubricate it to pre-vent it from rusting.
3. Use a chrome polish to shinechrome, aluminum and stain-less-steel parts, including theexhaust system. (Even thethermally induced discoloringof stainless-steel exhaust sys-tems can be removed throughpolishing.)
4. To prevent corrosion, it is rec-ommended to apply a corro-sion protection spray on all(even chrome- and nickel-plat-ed) metal surfaces.
5. Use spray oil as a universalcleaner to remove any remain-ing dirt.
6. Touch up minor paint damagecaused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry com-pletely before storing it or cov-ering it.
EWA00001
w
Make sure that there is no oil or
wax on the brakes and tires. If nec-
essary, clean the brake discs and
linings with a regular brake disc
cleaner or acetone, and wash the
tires with warm water and mild
soap. Then, carefully test the
motorcycle for its braking perfor-
mance and cornering behavior.
ECA00013
cC
8 Apply spray oil and wax spar-
ingly and wipe off any excess.
8 Never apply oil or wax on rub-
ber and plastic parts, but treat
them with a suitable care
product.
8 Avoid using abrasive polishing
compounds as they wear
away the paint.
NOTE:
Consult a Yamaha dealer foradvice on what products to use.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 72
Downloaded from www.Manualslib.com manuals search engine
7-4
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9
StorageShort-term
Always store your motorcycle in acool, dry place and, if necessary,protect it against dust with aporous cover.
ECA00014
cC
8 Storing the motorcycle in a
poorly ventilated room or cov-
ering it with a tarp while it is
still wet will allow water and
humidity to seep in and cause
rust.
8 To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chem-
icals are stored.
Long-term
Before storing your motorcycle forseveral months:
1. Follow all the instructions inthe “Care” section of thischapter.
2. Drain the carburetor floatchamber by loosening thedrain bolt; this will prevent fueldeposits from building up.Pour the drained fuel into thefuel tank.
3. Only for motorcycles equippedwith a fuel cock which has an“OFF” position: Turn the fuelcock to “OFF”.
4. Fill up the fuel tank and addfuel stabilizer (if available) toprevent the fuel tank from rust-ing and the fuel from deterio-rating.
5. Perform the following steps toprotect the cylinder, pistonrings, etc. from corrosion.
a. Remove the spark plug capand spark plug.
b. Pour a teaspoonful of engineoil into the spark plug bore.
c. Install the spark plug cap ontothe spark plug and place thespark plug on the cylinderhead so that the electrodes aregrounded. (This will limitsparking during the next step.)
d. Turn the engine over severaltimes with the starter. (Thiswill coat the cylinder wall withoil.)
e. Remove the spark plug capfrom the spark plug, install thespark plug and then the sparkplug cap.
EWA00003
w
When turning the engine over, be
sure to ground the spark plug elec-
trodes to prevent damage or injury
from sparking.
6. Lubricate all control cables andthe pivoting points of all leversand pedals as well as of thesidestand/centerstand.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 73
Downloaded from www.Manualslib.com manuals search engine
7-5
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9
7. Check and, if necessary, cor-rect the tire air pressure, thenraise the motorcycle so thatboth of its wheels are off theground. Alternatively, turn thewheels a little every month inorder to prevent the tires frombecoming degraded in onespot.
8. Cover up the muffler outletwith a plastic bag to preventmoisture from entering.
9. Remove the battery and fullycharge it. Store it in a cool, dryplace and recharge it once amonth. Do not store the bat-tery in an excessively cold orwarm place (less than 0°C ormore than 30°C). For moreinformation, see “Battery stor-age” in the chapter “PERIODICMAINTENANCE AND MINORREPAIRS”.
NOTE:
Make any necessary repairs beforestoring the motorcycle.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 74
Downloaded from www.Manualslib.com manuals search engine
8-1
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Specifications
Model TW125
Dimensions
Overall length 2,140 mm
Overall width 810 mm
Overall height 1,120 mm
Seat height 805 mm
Wheelbase 1,330 mm
Ground clearance 260 mm
Minimum turning radius 2,100 mm
Basic weight (with oil and fullfuel tank) 125 kg
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined single cylinder
Displacement 124 cm3
Bore × Stroke 57.0 × 48.8 mm
Compression ratio 10:1
Starting system Electric starter
Lubrication system Wet sump
Engine oil
Type
Recommended engine oilclassification API Service SE, SF, SG type
or higher
cCBe sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled “Energy
Conserving”) contain anti-friction additives which will cause
clutch and/or starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity
Periodic oil change 1.0 L
With oil filter replacement 1.1 L
Total amount 1.3 L
Air filter Wet type element
–10° 0° 10° 20° 30° 40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40
50°C
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 75
Downloaded from www.Manualslib.com manuals search engine
Fuel
Type Regular unleaded gasoline
Fuel tank capacity 7.0 L
Reserve amount 1.0 L
Carburetor
Type/quantity Y24P/1
Manufacturer TEIKEI
Spark plug
Manufacturer / Type NGK / DR8EA
Spark plug gap 0.6 ~ 0.7 mm
Clutch type Wet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 74/20 (3.700)
Secondary reduction system Chain drive
Secondary reduction ratio 50/14 (3.571)
Transmission type Constant mesh 5-speed
Operation Left foot operation
Gear ratio 1st 2.250
2nd 1.476
3rd 1.125
4th 0.926
5th 0.793
Chassis
Frame type Diamond
Frame type Pressed and steel tube frame
Caster angle 26°
Trail 95 mm
Tires
Type With tube
Front
Size 130/80-18 66P
Manufacturer/ BRIDGESTONE / TW31model
Rear
Size 180/80-14M/C 78P
Manufacturer/ BRIDGESTONE / TW34model
Maximum load* 180 kg
Air pressure (cold tire)up to 80 kg load*
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
8-2
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 76
Downloaded from www.Manualslib.com manuals search engine
8-3
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Front 150 kPa (1.50 kg/cm2, 1.50 bar)
Rear 150 kPa (1.50 kg/cm2, 1.50 bar)
80 kg load ~ Maximumload*
Front 150 kPa (1.50 kg/cm2, 1.50 bar)
Rear 175 kPa (1.75 kg/cm2, 1.75 bar)
Off-road riding
Front 125 kPa (1.25 kg/cm2, 1.25 bar)
Rear 125 kPa (1.25 kg/cm2, 1.25 bar)
*Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
Type Spoke wheel
Size 2.50 × 18
Rear
Type Spoke wheel
Size 14M/C × MT4.50
Brakes
Front
Type Single disc brake
Operation Right hand operation
Fluid DOT 3 or DOT 4
Rear
Type Drum brake
Operation Right foot operation
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm (Monocross suspension)
Shock absorber
Front Coil spring/oil damper
Rear Coil-gas spring/oil damper
Wheel travel
Front 160 mm
Rear 150 mm
Electrical
Ignition system C.D.I.
Charging system
Type C.D.I. magneto
Standard output 12 V, 11 A @ 5,000 rpm
Battery
Type GM7CZ-3D
Voltage, capacity 12 V, 7 AH
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 77
Downloaded from www.Manualslib.com manuals search engine
Headlight bulb type Incandescence
Bulb voltage, wattage × quantity
Headlight 12 V, 45 W/40 W × 1
Stop/tail light 12 V, 21 W/5 W × 1
Front flasher light 12 V, 21 W × 2
Rear flasher light 12 V, 21 W × 2
Marker light 12 V, 4 W × 1
Meter light 12 V, 3.4 W × 1
Neutral indicator light 12 V, 3.4 W × 1
High beam indicator light 12 V, 3.4 W × 1
Turn indicator light 12 V, 3.4 W × 1
Fuse
Main 20 A
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
8-4
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 78
Downloaded from www.Manualslib.com manuals search engine
1
2
3
4
5
6
7
9
8-5
SPECIFICATIONS
8
EAU01064
HOW TO USE THE CONVERSION TABLEAll specification data in this manual are listed in SIand METRIC UNITS.Use this table to convert METRIC unit data to IMPERIAL unit data.
Ex.
METRIC MULTIPLIER IMPERIAL
** mm × 0.03937 = ** in2 mm × 0.03937 = 0.08 in
METRIC TO IMPERIAL
Metric unit Multiplier Imperial unit
m • kg 7.233 ft • lb
Torque m • kg 86.794 in• lbcm • kg 0.0723 ft • lbcm • kg 0.8679 in • lb
Weight kg 2.205 lbg 0.03527 oz
Speed km/hr 0.6214 mph
km 0.6214 mim 3.281 ft
Distance m 1.094 ydcm 0.3937 inmm 0.03937 in
cc (cm3) 0.03527 oz (IMP liq.)Volume/ cc (cm3) 0.06102 cu • inCapacity lt (liter) 0.8799 qt (IMP liq.)
lt (liter) 0.2199 gal (IMP liq.)
kg/mm 55.997 lb/inMisc. kg/cm2 14.2234 psi (lb/in2)
Centigrade(°C) 9/5 + 32 Fahrenheit(°F)
CONVERSION TABLE
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 79
Downloaded from www.Manualslib.com manuals search engine
EAU01039
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
9-1
EAU02944
Identification number recordsRecord the key identification num-ber, vehicle identification numberand model label information in thespaces provided for assistancewhen ordering spare parts from aYamaha dealer or for reference incase the vehicle is stolen.
1. KEY IDENTIFICATIONNUMBER:
2. VEHICLE IDENTIFICATIONNUMBER:
3. MODEL LABEL INFORMATION:
EAU01041
Key identification numberThe key identification number isstamped on the key tag.Record this number in the spaceprovided and use it for referencewhen obtaining a new key.
1. Key identification number
EAU01043
Vehicle identification numberThe vehicle identification numberis stamped into the steering headpipe.Record this number in the spaceprovided.
NOTE:
The vehicle identification numberis used to identify your motorcycleand may be used to register yourmotorcycle with the licensingauthority in your state.
1. Vehicle identification number
1
1
16
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 80
Downloaded from www.Manualslib.com manuals search engine
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
9-2
EAU01049
Model labelThe model label is affixed to thelocation shown in the figure.Record the information on thislabel in the space provided. Thisinformation will be needed toorder spare parts from yourYamaha dealer.
1. Model label
1
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 81
Downloaded from www.Manualslib.com manuals search engine
siro page 4/6/0 3:58 AM Page 1
Downloaded from www.Manualslib.com manuals search engine
siro page 4/6/0 3:58 AM Page 1
Downloaded from www.Manualslib.com manuals search engine
PRINTED ON RECYCLED PAPER PRINTED IN JAPAN
99·5–0.2×1(E) !
YAMAHA MOTOR CO., LTD.
5EK-9-E1 Hyoshi3.3P-BLUE 4/6/0 11:47 PM Page 1 (1,1) (Cyan plate)
Downloaded from www.Manualslib.com manuals search engine