17 2011/12 Transport and lifting devices Extensive range Whether loads need to be weighed, lifted or moved, you will find a suitable product here. Comprehensive testing and quality assurance Guaranteed by means of rigorous product tests or in collaboration with suppliers who also take up the cause of quality. Special solutions Our application engineers will provide advice and assistance for the joint development of a cost-effective solution for requirements which cannot be met by the standard products. All-inclusive service We will provide support for all your needs – whether this is competent advice prior to purchase or through our inspection service afterwards. Weighing equipment ............... 18 Load-lifting magnets ............... 26 Pipe hooks .............................. 30 Manual hoists (lever hoists and pulley blocks) ................... 31 Manual hoists explosion-proof ....................... 37 Electric chain hoists................ 39 Rope hoists ............................. 50 Rope pulleys ........................... 51 Wire rope traction hoists ........ 52 Manual rope winches.............. 55 Electric rope winches.............. 57 HIT fork pallet trucks............... 58 Fork pallet truck ...................... 59 Transport rollers ..................... 62 HIT steel winches.................... 66 Hydraulic jacks ....................... 67 Hydraulic bottle jacks ............. 68 Hydraulic cylinders ................. 69 Hydraulic pumps ..................... 72 Hydraulic accessories............. 73
57
Embed
Transport and lifting devices - vazacitechnik.cz · Transport and lifting devices ... Manual hoists explosion-proof ... Dimension D mm 146 146 146 146 165 193 215 230 320 350 350
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
172011/12
Transport and lifting devices
Extensive range Whether loads need to be weighed, lifted or moved,
you will find a suitable product here.
Comprehensive testing and quality assurance Guaranteed by means of rigorous product tests or in
collaboration with suppliers who also take up the cause of quality.
Special solutions
Our application engineers will provide advice and assistance for the joint development of a cost-effective
solution for requirements which cannot be met by the standard products.
All-inclusive service
We will provide support for all your needs – whether this is competent advice prior to purchase or through
our inspection service afterwards.
Weighing equipment ............... 18
Load-lifting magnets ............... 26
Pipe hooks .............................. 30
Manual hoists (lever hoists and pulley blocks)................... 31
Reference no. 218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry
Reference no. 218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry218251 218251 218251 218251 218252 218253 218254 218255 on enquiry on enquiry on enquiry
Other units of measurement on enquiry.
NEW: The PFEIFER-plusNEW: The PFEIFER- crane scales series � plus points with PFEIFERWe offer you:
+ Trust � 3-year manufacturer�s warranty! We are sure!+ Optimum price � performance ratio+ Long service life � devices protected against dampness and dust - protection class IP65 - solid housing (aluminium, sheet steel)+ Handling � extremely compact design, low dead weight.+ Easy to use � switch on, weigh, done.+ Safety � integrated overload protection in all devices (a warning signal sounds on overloading)+ Reliability � maximum accuracy +/� 0.3 % of the suspended weight+ Flexibility � versatile in use, compact and light, many units of measurement can be set+ Selection � the right device for every application+ Advice � we advise you before and after the purchase. Our extensive network of technical advisors and our inspection service will be only too pleased to help!
= 10 plus points for our customers!
202011/12
PFEIFER Multi PlusUp to 12 remote-readable dynamometers on one read-out device!
Up to 12 dynamometers can be connected to one handheld device
Displays all individual values or the total value of all connected
dynamometers
Optional thermal printer can be supplied. By pressing a button, the
individual values and the total value are sent wirelessly to the printer
Individual! Choose the system configuration yourself
Plug & Play – the required system is supplied already configured
No troublesome cables – wireless connection (2.4 GHz) between
dynamometers, read-out devices and optional printer
Handy! Extremely small and light read-out device
Range up to 100 m (less inside buildings)Use of conventional 1.5 V batteries
Caution: The following table relates only to the dynamometer! Please order the
read-out device and optional printer separately!
Caution: Please order dynamometers, read-out devices and optional printers
Measuring range t 0.2 0.5 1 2 5Measuring range t 0.2 0.5 1 2 5Measuring range t 0.2 0.5 1 2 5Measuring range t 0.2 0.5 1 2 5Measuring range t 0.2 0.5 1 2 5Measuring range t 0.2 0.5 1 2 5Measuring range t 0.2 0.5 1 2 5
Dimension A mm 81 81 81 92 92Dimension A mm 81 81 81 92 92Dimension A mm 81 81 81 92 92Dimension A mm 81 81 81 92 92Dimension A mm 81 81 81 92 92Dimension A mm 81 81 81 92 92Dimension A mm 81 81 81 92 92
Dimension B mm 81 81 81 117 136Dimension B mm 81 81 81 117 136Dimension B mm 81 81 81 117 136Dimension B mm 81 81 81 117 136Dimension B mm 81 81 81 117 136Dimension B mm 81 81 81 117 136Dimension B mm 81 81 81 117 136
Dimension C mm 103 103 103 112 112Dimension C mm 103 103 103 112 112Dimension C mm 103 103 103 112 112Dimension C mm 103 103 103 112 112Dimension C mm 103 103 103 112 112Dimension C mm 103 103 103 112 112Dimension C mm 103 103 103 112 112
Dimension D mm 90 90 90 104 115Dimension D mm 90 90 90 104 115Dimension D mm 90 90 90 104 115Dimension D mm 90 90 90 104 115Dimension D mm 90 90 90 104 115Dimension D mm 90 90 90 104 115Dimension D mm 90 90 90 104 115
Due to the deep prism in the pole piece the round material is taken up safely.
HIT-NEO 125 Air Gap < 0.1 mm Air Gap 0.1 – 0.3 mm Air Gap 0.3 – 0.5 mm
Material thickness
mm
Max. L mm
Max. WLL kg
Max. L mm
Max. WLL kg
Max. L mm
Max. WLL kg
>=20 1500 125 1250 75 1000 60
>=15 1500 115 1250 70 1000 55
>=10 1250 110 1000 65 750 50
>= 4 800 45 600 40 500 30
>= 2 500 15 400 13 400 12
Ø 50 – 100 mm 2500 60 2500 40 2500 25
HIT-NEO 250 Air Gap < 0.1 mm Air Gap 0.1 – 0.3 mm Air Gap 0.3 – 0.5 mm
Material thickness
mm
Max. L mm
Max. W
mm
Max. WLL kg
Max. L mm
Max. W
mm
Max. WLL kg
Max. L mm
Max. W
mm
Max. WLL kg
>=25 2250 1000 250 2000 1000 170 1500 1000 105
>=15 2250 1000 205 2000 1000 150 1500 1000 90
>=10 2250 1000 170 2000 1000 130 1500 1000 85
>= 6 1750 1000 100 1500 1000 80 1350 1000 60
>= 4 1600 1000 50 1400 1000 45 1000 1000 36
Ø 50 – 200 mm 3500 – 125 3000 – 100 2500 – 70
HIT-NEO 500 Air Gap < 0.1 mm Air Gap 0.1 – 0.3 mm Air Gap 0.3 – 0.5 mm
Material thickness
mm
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
>=30 2500 1500 500 2350 1250 380 2150 1000 255
>=20 2500 1500 425 2350 1250 320 2150 1000 220
>=15 2500 1500 400 2350 1250 300 2150 1000 205
>=10 2500 1500 270 2350 1250 220 2150 1000 165
>= 8 2300 1500 195 2250 1250 160 2000 1000 125
>= 6 2000 1500 125 2000 1250 100 2000 1000 80
Ø 65 – 270 mm 4000 – 250 3500 – 200 3000 – 150
HIT-NEO 1000 Air Gap < 0.1 mm Air Gap 0.1 – 0.3 mm Air Gap 0.3 – 0.5 mm
Material thickness
mm
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
>=40 3000 1500 1000 3000 1500 845 2500 1250 650
>=30 3000 1500 860 3000 1500 730 2500 1250 565
>=25 3000 1500 830 3000 1500 705 2500 1250 550
>=20 3000 1500 745 3000 1500 640 2500 1250 510
>=15 3000 1500 500 3000 1500 445 2500 1250 380
>=10 2750 1500 285 2500 1500 240 2000 1250 200
Ø 100 – 300 mm 4500 – 500 4000 – 400 3500 – 300
WLL Chart HIT-NEO (L=length of load, W=width of load)
To be continued on the following
292011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Permanent magnet transporterFor manual operation: Model SH 12/4 (not suitable for crane operation)For manual and crane operation: Model SH 35 K
Easy handling of sheet steel and laminar steel parts in the production plant,
flame cutting plant, sheet metal warehouse etc.
The full adhesive force is reached on smooth, also untreated surfacesOil and fat hardly impair the adhesive force at all
Removal of the magnet transporter from the load using a free-moving,
mechanical pressing device
Temperature range up to 80 °C
Type SH 12/4 SH 35 K
Holding surface mm 133 x 106 190 x 110
Lifting capacity (SF:3) kg 90 250
Tractive force kg 50 110
Sheet metal thickness mm from 1.0 from 3.0
Weight kg 1.5 4
Reference no. 114592 114593
Permanent magnet with vertical loading device for lifting and swivelling flat material by 90° on enquiry
Load lifting magnets with battery and infrared remote control on enquiry
Magnetic cross-beam for HIT & BUX magnets on enquiry
Left:
Centre:
Right:
HIT-NEO 1500 Air Gap < 0.1 mm Air Gap 0.1 – 0.3 mm Air Gap 0.3 – 0.5 mm
Material thickness
mm
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
>=60 3500 2000 1500 3500 2000 1240 2500 2000 975
>=50 3500 2000 1300 3500 2000 1100 2500 2000 880
>=30 3500 1500 1000 3500 1500 860 2500 1500 750
>=20 3000 1500 825 3000 1500 750 2500 1500 675
>=15 3000 1500 480 3000 1500 450 2500 1500 410
150 – 350 mm 4500 – 750 4000 – 675 3500 – 600
HIT-NEO 2000 Air Gap < 0.1 mm Air Gap 0.1 – 0.3 mm Air Gap 0.3 – 0.5 mm
Material thickness
mm
Max. L mm
Max. W mm
Max. WLL kg
Max. L mm
Max. W kg
Max. WLL kg
Max. L mm
Max. W mm
Max. WLL kg
>=60 3500 2000 2000 3500 2000 1650 3000 1500 1300
>=50 3500 2000 1600 3500 2000 1300 3000 1500 1100
>=30 3500 2000 1350 3500 2000 1150 2500 1500 1000
>=20 3000 2000 1100 3000 1500 1000 2500 1500 900
>=15 3000 1500 650 3000 1500 600 2000 1500 550
150 – 350 mm 5000 – 1000 4500 – 900 4000 – 800
WLL chart HIT-NEO – continuation
302011/12
Pipe hooks
PFEIFER pipe hook with impact protection
Type PPHC for sensitive pipes
Careful handling of pipes without damaging the ends of the pipe
Optimum handling due to ergonomic arrangement of the handle
Maximum service life, since the impact cheeks are replaceable
BGR test is not a problem, because the opening width of the hook
is measurable thanks to a punch mark
Serial number and working load limit can be read off from the
handle and are undetachable
The soft, extremely well-adhering coating as well as the plastic impact cheeks
enable the careful handling of pipes, whose ends have been machined precisely. Example: Pipelines
The pipe hooks are attached in two-line suspension by means of shackles.
In order to attach the pipe, one pipe hook is fastened at each end of the pipe.
Dimensions of the required shackle: Eyebolt diameter max. 27.5mm;
clearance width of the shackle min. 33mm
Maximum pipe wall thickness 43mm
WLLkg
Reference no.
6700 212044
PFEIFER pipe hooks
Type PPH for standard applications in the factory
Optimum handling due to ergonomic arrangement of the handle
BGR test is not a problem, because the opening width of the hook is
measurable thanks to a punch mark
Serial number and working load limit can be read off from the
handle and are undetachable
These pipe hooks are used for the in-plant handling of pipes where the ends of
the pipe do not require special protection.
The pipe hooks are attached in two-line suspension by means of shackles. In order to attach the pipe, one pipe hook is fastened at each end of the pipe.
Dimensions of the required shackle: Eyebolt diameter max. 27.5mm;
clearance width of the shackle min. 33mm
Maximum pipe wall thickness 43mm
WLLkg
Reference no.
6700 212043
PFEIFER pipe hooks in use for the handling of sensitive pipes. Impact protection and coating reliably prevent damage to the ends of the pipe.
312011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Manual hoists (lever hoists and pulley blocks)
Which is the correct one? It all depends on the application!
The relevant questions are:� Level of mechanical stress on the chain hoist
� Ambient conditions (humidity, dust, explosive environment, effects of weather)
� Other influences (e. g. vibration, oscillation, short-term relief)
� Dimensional requirements for the chain hoist
� Stroke per lever movement or per meter of hand chain?
� Dead weight
Standard application?For standard applications the chrome HIT lever hoists and pulley blocks are the best choice. But what counts as a standard? A standard can be defined as:
� no excessive exposure to moisture and dust.
� no extreme mechanical stresses (impacts and shocks)
� no explosion protection required.
Sheet steel vs. cast devices?For lever hoists a distinction is made between devices made of sheet steel and those which are cast. Sheet steel devices are generally lighter and cheaper. Cast devices have a higher stability and longer lifetime.
Load chain?Appreciate the value of a lifting chain made in Europe. We have detected considerable safety deficiencies in some chains from the Far East. Our chain hoists always use chains from Europe.
Not much space? When space is limited (installation in inaccessible locations), then the dimensions are of utmost impor-tance. For these applications we suggest the lever hoist P07 and 360° pulley block, devices with the smallest dimensions and at the same time reduced manual force.
Dead weight? The dead weight is of par ticular importance when the device has to be lifted as well. The lever hoists made from sheet steel have the edge here. The extremely sturdy malleable cast iron device P95 is only marginally heavier.
Consider the following when making the selection:
Moisture and dust?Devices made from sheet steel have an open chain path. Moisture and dust can therefore get into the brake or the gear mechanism through holes for bolts etc. This does not adversely affect the device either outside or inside during normal use. Devices which are frequently exposed to considerable moisture (e. g. rain) or dust and dir t should be sealed accordingly. In such cases the most suitable lever hoists are the P95, P85 and AL devices as these have a closed chain path. The best pulley block is the 360 ° type, also with a closed chain path.
Frequent use or large lifting height? With frequent use or a large lifting height, the lift for each lever rotation for lever hoists or per meter move-ment of the hand chain for pulley
blocks plays an important role. This turns out to be relatively small due to the gear ratio in the gear mechanism. Check the suitability of the relevant device for your application in the technical data.
Mechanical strain?The hoist will be under more or less strain depending on the application. The so-called sheet steel devices are ideal for standard applications. For lever hoists subject to higher stresses e.g. impacts or shocks, it is best to use devices made of malleable cast iron (e. g. P95 and P85). Although the purchase costs are higher at the outset, these hoists are actually considerably more economical calcu-lated over the lifetime of the device. The aluminium lever hoist made from cast aluminium offers an optimum price-stability ratio.
In the following we offer you a selection of manual hoists, in which we already offer devices as a standard according to application.
We will be only too pleased to assist you in selecting the optimum hoist for your application! Just contact us!
Talk to your sales advisor or give us a call on:
+49 (0) 83 31-937-112 � We look forward to hearing from you.
322011/12
HIT Chrome lever hoistsTop quality for all-round use!
Optimum corrosion protection thanks to chrome plated, closed
sheet-steel housing and galvanised inner plates
Proven quality – 100% tested before shipment in the Pfeifer
headquarters, Memmingen
European, high-tensile, galvanised load chain according to EN
Low hand force due to optimum gear ratio and high-quality steel plain
bearings
Top price-performance ratio!
Usable from – 25 °C to +40 °C
360° swivelling hooksCan be used anywhere for lifting, pulling, tensioning and lashing!
WLL kg 750 1500 3000 6000
Number of chain legs Piece 1 1 1 2
Lever pressure at full load kg 14 22 32 34
Stroke for each lever rotation mmlever rotation mm 20 21 17 8
Overall height of hook from inner edge to inner edgeedge to inner edge
mm 325 380 480 620
Hook dimension, mm B 20.5 28 44 53
Hook dimension, mm C 30 36 40 50
Hook dimension, mm D 15 19 28 34
Weight with 1.5 m stroke kg 7 11 21 31
Reference no. with 1.5m stroke 218953 218954 218955 218956
Reference no. with 3m stroke 218957 218958 218959 218960
Additional lifting heights on enquiry!
The compact one – P07 lever hoistCompact, with low hand force – ideal for assembly works!
Pleasant handling due to extremely compact dimensions, reduced
lever force and low dead weight! You will be surprised!
Virtually wear-free brake, hence less maintenance costs, higher safety!
Maximum service life due to closed bearings, specially adapted lifting chain and extremely robust housing!
Compact dimensions enable it to be used in tight spaces.
High-quality European lifting chain according to EN
The adaptable one – 360° spur wheel pulley blockOperate it safely from outside the danger area!
Hand chain can be rotated by 360° – facilitates operation at a safe
distance from the load
Can also be operated without difficulty from above or from the side –
perfect for pulling and tensioning
Long-lasting because it is not susceptible to moisture and dust
thanks to the closed chain path
Top handling – compact dimensions and low hand force
High-quality European lifting chain according to EN
Robust, powder-coated sheet steel design
Operate it safely and conveniently next to the load. The rotatable hand chain
makes this unit particularly suitable for bulky loads.
WLL kg 500 1000 2000 3000 5000
Number of chain legs Piece 1 1 1 1 2
Overall height of hook from inner edge to inner edge
mm 300 335 395 520 640
Tensile force of hand chain at nominal load
daN 21 30 32 38 34
Stroke per 1m unreeling of the hand chain
mm 33.3 20.4 14.1 11.5 5.8
Hook dimension, mm B 17 22 30 38 45
Hook dimension, mm C 24 29 35 40 47
Hook dimension, mm D 14 19 22 30 37
Weight with 3m stroke kg 8.7 10.6 15 23.4 37.5
Reference no. with 3 m stroke 169228 169229 169230 169231 169232
Reference no. with 6 m stroke 238991 238992 238993 238994 238995
Other lifting heights on enquiry!
The miracle space-saver – 360° pulley block with integrated roller running gearMakes best use of the height!
Optimum utilisation of the ceiling height thanks to its own extremely small height
Inherently stable – no wobbling or rocking since the pulley block is rigidly attached to the geared trolleys
Hand chain can be rotated by 360° – facilitates operation at a safe distance from the load
Fast assembly due to infinite adjustment of the round nuts
Tipping protection, wheel-fracture protection, and approach buffers as a standard
Long-lasting because it is not susceptible to moisture and dust thanks to the closed chain path
High-quality European lifting chain according to EN
Robust, powder-coated sheet steel design
Operate it safely and conveniently next to the load. The rotatable hand chain makes this unit particularly suitable for bulky loads.
Roller and ball bearings on all rotary par ts
WLL kg 500 1000 2000 3000 5000
Number of chain legs 1 1 1 1 2
Overall height of hook from inner edge to inner edge
mm 245 272 323 382 550
Tensile force of hand chain daN 21 30 32 38 34
Beam flange width mm 50–180 50–180 58–180 74–180 98–180
Weight with 3m stroke kg 20 27 44 77 125
Reference no. with 3m stroke 161263 161264 161265 161266 161267
Reference no. with 6m stroke 238997 238998 238999 239000 239001
Higher working load limits and carrying flange widths up to 300mm and with winder running gear on enquiry.
Other lifting heights on enquiry!
372011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Manual hoists explosion-proof
Explosion-proof version � Pulley block 360° For use in potentially explosive environments
� ATEX classification: II 2 GD c IIB T4 T 125° C X and
II 2 GD c IIB T3 T 145° C
� Copper-plated hook
� Special brake for reduced heat generation
� Hand chain in stainless steel, galvanised load chain, optionally in stainless steel
� Top corrosion prevention from MKS coating of all metal surfaces
� Protection from soiling and corro-sion thanks to closed housing and closed chain path.
� Lift safely outside the danger zone. The 360° revolving hand chain enables operation from the side at a safe distance from the load.
� Can also easily be operated from above or from the side. Also ideal for tensioning or pulling.
Uno-Ex lever hoistFor use in potentially explosive environments
� ATEX classification: I M2 II 2 GD c IIB T4 T120° C X
� Copper-plated hook
� Galvanised load chain, optionally in stainless steel
� Special brake for reduced heat generation
� Robust sheet steel construction
� Low dead weight
Explosion-proof version 360° pulley block with
integrated trolley
� ATEX classification: II 2 GD c IIB T4 T 125° C X
II 2 GD c IIB T3 T 145° C
� Copper-plated hook, rollers made from solid bronze
� Special brake for reduced heat generation
� Hand chain in stainless steel, galvanised load chain, optionally in stainless
steel
� Top corrosion prevention from MKS coating of all metal surfaces
� Protection from soiling and corrosion thanks to closed housing and closed
chain path.
� Maximum use of room height thanks to very small overall chain hoist
height.
� No shaking, no swinging. Very stable in itself as the pulley block is
mounted securely on the trolley.
� Trolley with wheel fracture protection and approach buffers
� Lift safely outside the danger zone. The 360° revolving hand chain enables
operation from the side at a safe distance from the load.
382011/12
Roller running gearSuitable for manual, electric and pneumatic hoists
Very simple, virtually infinite adaptation to various beam flange widths
Adjustable for wide range of beams and different profiles (e.g. INP, IPE, IPB)Optimum running characteristics due to ball-bearing-mounted rollers
Tipping protection and wheel fracture protection as standard
Centric suspension of the hoist in the eye cross beam – no lateral wandering on
the cross beam500/1000/2000 versions, small flange widths in blue
WLLkg
Beam flange widthmm
max. flange thicknessmm
smallest curve radiusm
Weightkg
Reference no.
500 50–220 24 0.90 5.2 115188
500 160–300 40 0.90 10.6 115189
1000 58–220 30 1.00 9.0 115190
1000 160–300 40 0.90 12.0 115191
2000 66–220 36 1.10 13.5 115192
2000 160–300 40 1.15 19.3 115193
3000 74–220 25 1.40 32.0 115194
3000 160–300 40 1.40 35.8 115195
5000 90–220 25 1.80 48.0 115196
5000 180–300 40 1.80 52.2 115197
Reel running gearVersion like roller running gear; however, driven by means of hand
chain via a hand chain sprocket. With galvanised hand chain for 3 m
running track height.
Other chain lengths for higher running tracks on enquiry.
WLLkg
Beam flange widthmm
max. flange thicknessmm
smallest curve radiusm
Manual force at rated loaddaN
Weightkg
Reference no.
500 50–220 25 0.90 3 9.7 168186
500 160–300 40 0.90 3 12.6 168187
1000 58–220 25 0.90 6 11.2 168188
1000 160–300 40 0.90 6 14.1 168189
2000 66–220 25 1.15 7 18.0 168190
2000 160–300 40 1.15 7 21.3 168191
3000 74–220 25 1.40 7 35.4 168192
3000 160–300 40 1.40 7 39.2 168193
5000 90–220 25 1.80 9 51.8 168194
5000 180–300 40 1.80 9 56.0 168195
Beam clampsFor fastening an attachment point to an I-beam
Also suitable for the lifting of I-beams in a vertical direction
Easy and simple assembly, adjustable to the beam size using the screw jack
For the vertical suspension of hoistsLow overall height
Also suitable for I-sections with inclination of the lower flange up to 20%
WLLkg
Dimensions in mm Weightkg
Reference no.B
min.B
max.B1
max.D E
min.E
max.
2000 75 260 215 23 102 155 5.2 136879
3000 80 354 320 24 140 225 10.0 198086
5000 80 354 320 28 140 225 11.3 136881
392011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Electric chain hoists
The selection of the correct electric chain hoist depends primarily on the application.
The following questions arise:– Necessary hook travel
– Suspension height
– Frequency of application (rarely, more frequently, continuous operation)
– Type of operation (longer distances without a break or frequent switching/lifting/lowering)
– Environmental conditions (temperature, hygiene requirements, aggressive environment, e.g. offshore or explosive environment)
Duty cycleSpecifies the operating/pause ratio of the electric chain hoist.
This is specified in %. Although the minimum values are specified in the standards, the performance of many chain hoists is better than that demanded by the standard.
Full load hoursThis number indicates the period of operation after which the chain hoist must be subjected to a “big” service or a general overhaul. This limit is reached sooner or later, depending upon the application or frequency of operation.
It is calculated on the basis of the hook travel employed, the number of operations per day and the lifting speed.
Motor groupaccording to FEM 9.511The FEM is divided into the classes 1DM to 5 m, whereby 5 m is the best class. The following are indicated for each class in the FEM:
– The minimum requirement for the duty cycle
– The maximum length of time that the chain hoist may be operated without a break
– The maintenance intervals in full load hours
The correct class is to be selected here depending on the application!
Depending upon the individual application, the correct hoist can then be selected with the following parameters:
Number of legsThere are electric chain hoists with one or more legs. The more legs, the higher the working load limit of the chain hoist for the same motor power. However, many legs mean a lower lifting speed and cause long chain lengths = high weight, large chain store.
Limit switchesThere are limit switches for lifting and lowering. The load movement is stopped if the load hook reaches a certain position at the top or bottom. This prevents the hook from being driven against the housing at the top or to the stop of the load chain at the bottom. The integrated friction coupling is relieved as a result, extending the service life.
Type of controlIn general there are two types of control. Direct control and contactor control. Direct control means that the operating voltage (400 V) is switched directly in the pendant control panel. In the case of contactor control, the operating voltage is converted to a low voltage and this is switched in the pendant control panel. This option may be useful depending on the environment, e.g. humidity. Certain other parameters, such as stroke limit switches, may make contactor control necessary.
In the following we offer you a selection of electric chain hoists, in which we already offer devices as a standard according to application.
We will be only too pleased to assist you in selecting the optimum hoist for your application! Just contact us!
Speak to your technical advisor or call us:
+49 (0)83 31-937-112 – we look forward to your call!
402011/12
Electric chain hoists for standard service with standard lifting height, hook suspension and 2 lifting speeds
Selection criteria: flexibly usable with good price-performance ratio
thanks to high degree of standardisation
Fast lifting or exact positioning possible by means of two lifting
speeds
Safe! Protected against overload by friction coupling
Pleasant handling due to compact dimensions and low dead weight.
Long life! Dust and splash-proof (protection class IP55 / insulation
class F)
High performance chain hoist, made in Germany
All models include chain store
With hook suspension
This chain hoist is characterised by its great flexibility. The hook suspension can be hung up in an eye, a ring or optional running gear – depending upon needs.
The standard from 250 kg to 2,000kg
Other lifting heights on enquiry!
Suitable beam trolleys and beam clamps on page 38
WLL kg 250 500 1000 2000
Model 250/1-8/2 500/1-10/2.5 1000/2-5/1.25 2000/2-3/0.75
Main stroke m/min 8 10 5 3
Fine stroke m/min 2 2.5 1.25 0.75
Number of chain legs 1 1 2 2
Motor group FEM 9.511 2 m 2m 2m 1 Am
Duty cycle, main % 40 60 60 60
Duty cycle, fine % 25 25 25 25
Dimension of load chain mm 4 x 12 7.2 x 21 7.2 x 21 7.2 x 21
Lifting motor (400V 50 Hz) kW 0.32/0.08 0.9/0.2 0.9/0.2 1.1/0.2
Reference no. with 3m stroke, 1.5 m control cable and hook suspension
Reference no. with 10m stroke, 8.5 m control cable and hook suspensionand hook suspension
237403 237406 237409 237412
412011/12
The simple ones from 250 kg to 6,300kg
Electric chain hoists for occasional use! One lifting speed, directly controlled.
Selection criteria: application-
specific implementation with top price-performance ratio
Long life! Dust and splash-proof (protection class IP55 / insulation
class F)
Safe! Protected against overload by friction coupling
Usable e. g. in the workshop or for the occasional movement of loads in industry
and handicraft
All models include chain storeDirectly-controlled 5 tonne and 6.3 tonne version, contactor-controlled with limit
switch
Operating voltage 400 V AC/50 Hz
One speed for lifting and loweringWith eye or hook suspension or with manual or electric running gear
Further options available from standard. Please enquire:
Other lifting heights (higher and lower) and other lifting speedsContactor control or radio remote control, e. g. in a damp environment or in the
case of heavy demands on the pendant control panel. – For additional safety!
Hoist limit switch for lifting and lowering. Reliably prevents the load hook from
driving into the stop at the top or bottom.Electric running gear with other driving speeds up to 25 m/min or 2 driving
speeds
Tip: Electric running gear should be used for loads of 1,000kg or more! Such
heavy loads can no longer or hardly be moved at all by a manual running gear!
Caution! In the case of the chain hoists with the reference numbers 217800, 217801 and 217802, an additional attachment point is required in order to relieve
the chain store. In the case of chain hoists with running gear, a trailing running gear is required. Please order at the same time!
Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16Driving speed, electric running gear type N m/min 16 16 16 16 16 16 8 8 4/16 4/16
Beam flange width, running gear type N mm 50Beam flange width, running gear type N mm 50Beam flange width, running gear type N mm 50– 106 50106 50– 106 66106 66– 135 66135 66– 135 66135 66– 135 66135 66– 135 82135 82– 155 82155 82–155 90155 90 –155 90155 90 –155
422011/12
The continuous runnersfrom 250 kg to 5,000kg
Electric chain hoists that are used frequently and often switched on/off!
Selection criteria: High duty
cycle, high motor group, number of permissible switchings per hour
Fast lifting and positioning to the exact millimetre due to 2 lifting
speeds
Low-maintenance due to high motor group
Long life! Dust and splash-proof (protection class IP55 / insulation
class F)
Safe! Protected against overload by friction coupling
Employed wherever the chain hoist is used very frequently or switched frequently
on the pendant control panel, e. g. on swivelling cranes at a loading point etc.
Directly controlled, operating voltage 400 V AC/50 Hz
Models 091/56 and 111/52 include contactor controller and limit switchWith eye or hook suspension or with manual or electric running gear
Further options available from standard. Please enquire:
Other lifting heights (higher and lower) and other lifting speeds
Contactor control or radio remote control, e. g. in a damp environment or in the case of heavy demands on the pendant control panel. – For additional safety!
Hoist limit switch for lifting and lowering. Reliably prevents the load hook from
driving into the stop at the top or bottom.Trolleys for other flange widths and other driving speeds
Caution! In the case of the chain hoists with the reference numbers 218126, 218127 and 218128, an additional attachment point is required in order to relieve the chain store. In the case of chain hoists with running gear, a trailing running gear is required. Please order at the same time!
Reference no., manual running gear type N 218204 218205 218206 218207 — —Reference no., electric running gear type N 218227 218228 218229 218230 218231 218232
Driving speed, electric running gear type N m/min 5/20 5/20 5/20 5/20 4/16 4/16
Beam flange width, running gear type N mm 50–106 66–135 82–155 82–155 90–155 90–155
Caution! In the case of the chain hoists with the reference numbers 217818, 217819, 217823, 217824, 217825, 217827, 217828, 217829, 217830, 217831, an
additional attachment point is required in order to relieve the chain store. In the case of chain hoists with running gear, a trailing running gear is required. Please order at the same time!
* The hook travel describes the entire distance (lifting and lowering) travelled by the hook. If the maximum hook travel is used, then the chain hoist must cool down completely afterwards.
Trailing running gearReference no.
218233
442011/12
The indestructible onesfrom 2,500 kg to 30,000 kg
Electric chain hoists for extreme stresses
Selection criteria: High duty cycle, high motor group, sturdy and
precise manufacture, best material and construction, lowest wear
Long life, low wear inner workings
Extremely sturdy design
High basic standard
This chain hoist is used in applications where the equipment is subjected to ex-treme stresses. The entire construction is designed down to the tiniest detail for
extreme loads. Whether it be for offshore, drilling rigs, tunnel construction, mili-
tary, mining or other extreme applications, this chain hoists copes with just anything!
Extremely wear-resistant, because: the chain driving sprocket is milled from spe-
cial steel; highly precise, diagonally-toothed gears; German lifting chain specially
matched to the sprocket, defined chain intake with twist protection Overload protection by means of friction coupling or power-off
Motor group 2 m also for high working load limits – therefore low maintenance;
high duty cycle – therefore frequent loading possible
Defined sealing of the equipment with o-rings (is also sealed 100% again after service)
Extra-sturdy, ventilated brake motor with thermal monitoring (switches off before
overheating)
Extra-sturdy steel housing, dust and splash-proof – protection class IP55 / insula-tion class F
All models include chain store
Contactor control 42 V DC. Greater safety in damp environments or in the case of heavy demand on the pendant control panel
Fast lifting and positioning to the exact millimetre due to 2 lifting speeds
With stroke limit switches – reliably prevent the load hook from driving into the
stop at the top or bottom.Operating voltage 400 V AC/50 Hz
Electric chain hoists for the “normal” 230 V socket! Incl. 1 m cable and plug.
Plug in and start working!
Operation with 230 V socket
With hook suspension for
flexible use
Long life! Dust and splash-proof (protection class IP55 / insulation
class F)
Safe! Protected against overload by friction coupling
Chain hoists from this series are particularly suited for installation work. The par-
ticular advantage is the flexibility. The chain hoist can be used wherever there is a mains socket.
All models include chain store
Directly controlled
Operating voltage 230 V AC/50 Hz
WLL kg 250 500 1000 2000
Model 020/01 020/01 050/02 070/01
Description 250/1-8 500/2-4 1000/2-4 2000/2-3
Main stroke m/min 8 4 4 3
Number of chain legs 1 2 2 2
Motor group FEM 9.511 2m 2m 1Am 1Am
Motor group load chain EN 818-7 1Bm 1Bm 1Bm 1Bm
Duty cycle, main % 40 40 40 40
Max. permissible switchings per hour 240 240 240 240
Dimensions of load chain mm 4×12 4×12 5.2×15 7.2×21
Lifting motor (230V 50 Hz) kW 0.25 0.25 0.55 1.1
Reference no. with 3m stroke, 1.5 m control cable and hook suspensionand hook suspension
218129 218130 218131 218132
Reference no. with 6m stroke, 4.5 m control cable and hook suspensionand hook suspension
218133 218134 218135 218136
Reference no. with 10m stroke, 8.5 m control cable and hook suspensionand hook suspension
218137 218138 218139 218140
Further options available from standard. Please enquire:
Other lifting heights (higher and lower) and other lifting speedsElectric or manual running gear
PFEIFER is your specialist for electric chain hoists … … far beyond the catalogue!
Are you looking for an electric chain hoist for a special application? We know what it depends on and will select the correct equipment for you!
Do you have special requirements and wishes? We will be only too pleased to determine the correct chain hoist for you, even far beyond the offer in our catalogue!
Do you need neutral advice and selection of a suitable chain hoist? We offer you the correct chain hoist – neutrally, objectively and independent of the manufacturer!
Do you need an on-site consultation? Our technical advisors will be only too pleased to visit you and discuss your application!
Our inspection service takes care of the annual inspection as well as the servicing of your equipment, either on-site or at one of our service centres!
Our claim:We advise you on your individual application professionally and objectively! We offer the correct electric chain hoist including service for every customer and every application!
Just contact us: +49 (0) 83 31-937-112
462011/12
Electric chain hoists for special applications
HandymasterFor crane-assisted working
This chain hoist facilitates working wherever loads need to be lifted and guided precisely without problems. Load hooks and pendant control panel thereby form an ergonomically shaped, fixed unit.
Suitable for any kind of workplace where moderate to heavy loads need to be moved frequently. e.g. assembly, dispatch and logistics etc.
The load can be lifted and guided with just one hand!
– Lower hook lockable, facilitates work in the case of constantly repeated operational sequences
– No separate, bothersome pendant control panel
– Available with hook suspension, eye, roller running gear or electric running gear
Electric chain hoist with stainless steel chainFor work in hygienic or particularly aggressive environments
Equipped with a stainless steel chain and optional food-safe lubrication, this chain hoist is par ticularly suitable for use in clean environments. Together with the food-safe lubrication, it is outstandingly well suited for use in the food industry. e.g. dairies, breweries, mineral water wells.
In aggressive environments, where a galvanised lifting chain corrodes fast, the stainless steel chain extends the service life enormously.
Electric chain hoist in explosion-proof designFor use in potentially explosive environments
In the chemical and pharmaceutical industry as well as in other fields, gases or dusts may be generated that can explode due to unprotected electrical appliances.
In order to prevent this, PFEIFER offers a wide range of explosion-proof chain hoists complying with the latest ATEX standard, including all necessary approvals and documents. In addition, a suitable main switch and installation cable can be delivered together with the chain hoist.
We offer the following safety classes:
Gas-Ex: ATEX II2G Eex cde IIB T4, zone 1
ATEX II2G Eex cde IIC T4, zone 1
ATEX II3G Eex nA II T3, zone 2
Dust-Ex: ATEX II2D Eex cde IIB T4 IP65, zone 21
ATEX II3D IP55, 135°, zone 22
472011/12
Pneumatic hoists from 250 kg to 6,000 kgUsable in continuous operation, duty cycle 100%
Optimum handling due to infinitely variable lifting speed and low dead
weight
Fast working – high lifting speed shortens the idle stroke time, espe-
cially in the unloaded condition
Safe and insensitive since no electricity present. Also no problem to use outdoors
Proven in many applications!
E.g. chemical and pharmaceutical industry (explosion-proof version), automotive industry, shipbuilding,
paint shops, refineries, foundries, paper and food industry… no doubt in your application too!
Pneumatic hoists have a duty cycle of 100%. That means that these devices can be used without any breaks in operation at all.
Furthermore, they offer the advantage of a relatively low dead weight, in particular for high working load limits. The lifting
speed is also high, especially in the unloaded condition.
Robust cast steel housing
Supplied with chain store
Standard lifting height 3 m, rope control (2.5 m), suspension hook
Weight per unit length approx. kg/m 0.677 1.004 2.33Weight per unit length approx. kg/m 0.677 1.004 2.33Weight per unit length approx. kg/m 0.677 1.004 2.33Weight per unit length approx. kg/m 0.677 1.004 2.33Weight per unit length approx. kg/m 0.677 1.004 2.33
For the transport of persons With electronic overload
protection
For moving loadsWith slack rope switch Infinitely variable speed
Special designs on request
532011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Ropes for traction hoistsRopes for traction hoists have to meet specific requirements (e. g. pre- forming) and have special properties (such as extreme crushing strength).
The unrivalled manufacturing expertise of our subsidiary PFEIFER DRAKO in
Mülheim/Ruhr enables it to ensure the highest quality and wear-resistance for
a long service life.You can identify original PFEIFER DRAKO continuous winch ropes by the blue
strand.
Ropes for guided loadsYou can use these ropes when your loads are guided by rollers, rails, etc. so that
untwisting of the ropes is prevented.
Rope diameter mm 8.4 9 10.2
Rope-end stylePress-fitted eye hook at one end
Press-fitted eye hook at one end
Press-fitted eye hook at one end
Minimum breaking force rope F
min
kN 55 65.7 86
Weight per unit length
approx. kg/m 4.304 4.458 4.757
Reference no. 235866 235867 235868
Ropes for unguided loadsThese cables are extremely rotation-resistant, meaning they do not rotate under
load and can therefore be used for lifting where it is not possible to guide the load.
Rope diameter mm 8 9 10
Rope-end stylePress-fitted
swivel hook at one end
Press-fitted swivel hook at
one end
Press-fitted swivel hook at
one end
Minimum breaking force rope F
min
kN 55.3 69.2 83
Weight per unit length
approx. kg/m 4.736 5.077 5.599
Reference no. 235869 235870 235871
!Rope handling
Reel Winding DeviceWinder Willi
Careful rope handling and protection from mechanical damage
Further information on how to handle your ropes exper tly with the winder willi can be found on page 236.
Accessories
dual lift® arresting deviceIn accordance with the requirements of EN 1808, every winch for the transporta-
tion of persons requires a safety system on an independent safety rope. The OSL (Overspeed Safety Lock) trips a clamping jaw mechanism if the fall speed reach-
es 30 m/min. The ISL is a mechanism closing at a rope inclination or an inclina-
tion of teh platform of >10°
Description OSL508 CE OSL1010 CE OSL809 CE
Reference no. 238481 238488 238483
Description ISL508 CE ISL1010 CE ISL809 CE
Reference no. 238489 238491 238490
!PFEIFER is an authorised service company for the inspection of dual lift
®
wire rope traction hoists
OSL ISL
542011/12
dual lift® connection adapterApart from the four mounting holes, the wire rope traction hoists can also be
connected via an adapter. This can be used on various connections. A custom-
Simple operation/unlimited rope length/light and handy
Stroke limitation and rope run-out protection by means of limit switches (the scope of supply of the motorised rope hoist includes a 2.5 m control cable, winder with 10 m rope with hook, 2 limit switch springs with hexagonal wrench in cardboard
packing.)
Model Tr 11 Tr 31 Tr 30S Tr 50
WLL kg 100 300 300 500
Rope diameter mm 6.5 6.5 6.5 6.5
Rope speed m/min 15 5 12 7
Power kW 0.37 0.37 1.1 1.1
Dead weight kg 21 21 31.6 31.6
Reference no. 136430 136431 136432 136433
!PFEIFER is an authorised service company for the inspection of wire rope traction hoists.
552011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Manual rope winches
Rope winch, manually operatedTensile force 900 daN
Easy, jerk-free lifting, lowering and pulling
Load pressure brake
Drive crank removable (version with automatic unroll function)Also usable with belt; note: order belt fastener at the same time
Type SSW 900/1 Automatic unroll function SSW 900/2
Tensile load in the 1st rope position daN 900 900
Tensile load in the uppermost rope position daN 330 330
Wire rope diameter mm 7 7
Total rope uptake m 25 25
Gear assistance 8.75:1 8.75:1
Weight without rope kg 7.5 7.5
Reference no. 136442 136443
Description Rope, 20m, with hook Rope, 20 m, with hook
Reference no. 148439 148439
Description Belt fastener Belt fastener
Reference no. 188349 188349
Description Belt, 5.5m, with triangular hook Belt, 5.5m, with triangular hook
Reference no. 181051 181051
Wall-mounted rope winch
with aluminium housing
Self-locking
Removable crank
Low crank force
Low noiseCorrosion-resistant
Surface powder-coated
Compact form, encapsulated housing
Tensile load daN 50 100
maximum rope uptake m 12 8
Rope diameter mm 2 3
Stroke per crank revolution mm 96 38
crank pressure kg 8 6
Weight kg 1 2
Reference no., winch 156037 156038
Reference no., rope with thimble
236541 236542
Rope and end fittings for the rope on enquiry.
562011/12
Wall-mounted rope winch
galvanised, with wall mounting
Self-locking
Direction-independent rope outlet, large rope capacity
Low noiseCorrosion-resistant
Compact form, encapsulated housing
Folding crank handle
Tensile load daN 300 500
maximum rope uptake m 29 22
Rope diameter mm 4 5
Rope drum diameter mm 60 60
Stroke per crank revolution mm 65 46
Transmission ratio 1/3.1 1/4.5
Weight kg 5 5
Reference no., winch with wall mount
156039 156040
Reference no., winch with bracket mount
200208 200209
Reference no., rope with thimble
236543 236544
Rope and end fittings for the rope on enquiry.
Wall-mounted rope winch
Painted
Self-locking, recoil-free safety crank with folding handleLoad pressure brake to prevent unintentional lowering of the load
Protected against corrosion
Maintenance-free plain bearing
Simple and space-saving wall installationComplies with UVV BGV D8
Tensile loaddaN
maximum rope uptake
m
Rope diametermm
Stroke per crank revolution
mm
crank pressurekg
Weightkg
Reference no., winch
Reference no., rope with thimble
300 11 6.0 74 18 10 156041 236545
500 10 6.5 30 21 10 156042 236546
750 12 8.0 28 20 14 156043 236547
1000 10 9.0 19 18 15 156044 236548
2000 8 12.0 16 32 23 156045 236551
3000 7 13.0 10 30 32 156046 236552
Rope and end fittings for the rope on enquiry.
572011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Electric rope winches
Transport and loading of goods, conveying of materials and persons, shifting from left to right, from top to bottom, diagonally and crosswise in each case. Convinc-ing, large performance range as regards load bearing capacity, lifting height and speed. Functional design, sturdy and purposeful at
the same time. PFEIFER offers the correct rope winch for every appli-cation with a wide range of cus-tomisable options such as various connection options (230 V, 400 V) and special equipment such as drum free-wheeling, slack rope switch, remote control, explosion protection or transport of persons.
For multi-rope
operation
With flanged pulley
enlargement
For the transport
of persons
With electronic overload
protection
Drum free-wheeling can be
activated
For moving loads back and
forth
With slack rope switch
With brake ventilating
mechanism plus hand wheel
Infinitely variable speed
WLL kg 125 250 250 250 500 630 980 1250 1600 3200
Model Mini Mini Mini Mini BG 1 BG 1 BG 2 BG 2 BG 3 BG 3.5
Roller skate transport setsFor short, variable transport routes
For the transport of moderately heavy loads, e. g. machines and
machine parts, to the place of operation
Permits driving around corners thanks to pivot plates with a
maximum pushing speed of 5 m/min
Components of the roller skate transport sets: 4 roller skates, 2 steering bars, 2 pivot plates, 2 tie rods, 2 levelling pieces, 1 sheet metal case. The components
can also be supplied separately.
Please note: The road surface is decisive for a trouble-free transport process,
not the working load limit of the roller skate. Tiles and asphalt are unsuitable, concrete is only conditionally suitable; sturdy metal sheets should ideally be
underlaid (at least 10 mm thick).
WLL per setkg
Roller Ømm
Load surfacemm
Overall heightmm
Pivot plate Ømm
Weight per setkg
Reference no.
20000 18 120×120 108 130 48 114241
30000 24 120×120 117 130 56 114242
60000 30 130×130 140 150 90 114243
Pry bar rollers
An indispensable aid
For lifting machines or other articles with little or no floor clearance
Ideal handling – long 1.6-metre lever facilitates the raising of heavy
articles as well!
Robust! – grip and load bearing part made of forged steel
Quality made in Germany!
Ideally suited for creating the necessary floor clearance in order to push a jack or roller chassis underneath.
With rubber rollers made of highly resistant armoured rubber for low-noise, safe
operation without slipping.
WLL kg 3000
Lever length mm 1600
Weight kg 14
Reference no. with iron rollers 155711
Reference no. with rubber rollers 155712
662011/12
HIT steel winches
Top stability – solid baseplate with profile provides for optimum
stability, even on dirty surfaces!
Top service life – rack made of specially hardened steel, therefore
low wear; highest manufacturing precision of each individual part;
solid implementation of the crank element; extra-thick foot claw;
ideal machining of the housing from solid sheet steel!
Made in Germany!
Universal, free-moving lifting device for the simple raising of loads. Depending upon conditions, the foot claw or the head can be applied. The shape of these
two points reliably prevents the load from slipping.
The self-locking crank holds the load securely in any position! The crank handle
is foldable.All devices are available with safety crank or ratchet crank!
Version with adjustable lifting claw also available. The claw can be attached at 10
different heights.
Type 100 steel winches in accordance with DIN 7355WLL kg 1500 3000 5000 10000
Overall height mm 725 725 725 800
Lifting height mm 350 350 300 300
Claw height in the lowest position
mm 70 75 70 90
Weight kg 12 20 24 42
Reference no. with safety crank
242031 242032 242033 242034
Reference no. with ratchet crank
242035 242036 242037 242038
Type 200 steel winches with smaller overall heightWLL kg 1500 3000 5000 10000
Overall height mm 570 570 600 650
Lifting height mm 300 300 300 300
Claw height in the lowest position
mm 70 75 70 80
Weight kg 11 18 22 38
Reference no. with safety crank
242039 242040 242041 242042
Reference no. with ratchet crank
242043 242044 242045 242046
Type 300 steel winches with adjustable foot clawsWLL kg 1500 3000 5000 10000
Overall height mm 725 725 725 725
Lifting height mm 350 350 300 300
Claw height in the lowest position
mm 80 80 80 80
Claw height in the highest position
mm 670 670 670 670
Weight kg 17 23 29 46
Reference no. with safety crank
242047 242048 242049 242050
Reference no. with ratchet crank
242051 242052 242053 242054
672011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Hydraulic jacks
Long service life due to extremely robust construction and high
service-friendliness
Minimal costs spread over the service life
Safe and simple with relief valve – protects against overload
Simply to use! Head and foot claw have the same, specified lifting
force
Sturdy and stable due to high-quality special steel, robust hydraulics
and wear-resistant seals
Service-friendly, as it can be completely dismantled and optimum
spare part supply
Flexibly usable! As little as 26mm floor clearance suffice for the
5 tonne and 10 tonne version.
Simple handling due to compact design and removable hand lever
Hydraulic jacks are used wherever machines of the most diverse types need to be raised, for example for repair or assembly work.
Whether for the maintenance of heavyweight processing centres in industry or
for the repair of vehicles, fork lift trucks, construction machines or lorries, these devices are indestructible and always provide faithful service.
A big advantage of these devices is also their service-friendliness and longevity.
PFEIFER hydraulic jack
The original – still unique today!
WLL kg 5000 10000 20000
Lifting height mm 205 240 220
Lifting range with lifting foot
mm 26– 231 26 –266 60 – 260
Lifting range with lifting head
mm 362– 567 415 – 655 440 –660
Dimensions L × W × H mm 575×130×362 585×130×415 850×180×440
Weight kg 19 25 52
Reference no. 114307 114333 114335
682011/12
Hydraulic bottle jacks
Saving time due to screwable spindle – prevents idle stroke and
installation of the jack underneath
Ideally suited for straightening work, e.g. on sections, frames or
steel structures, because they can be used horizontally and vertically
The right jack for every application: Whether for a long stroke or
cramped conditions – the range extends from standard to mini!
Safe, stable footing due to large baseplate
Finely controlled lowering
Designed and constructed for use by professionals. High-quality
branded goods.
Bottle jacks of this type can be found in almost every workshop. Whether as a
classic vehicle jack for raising machines or for alignment work.
Standard jacksLifting load t 3 5 8 12 15 20
Lifting height mm 114 121 121 149 156 159
Overall height, retracted mm 191 200 200 241 230 270
Overall height, extended mm 365 391 391 470 495 469
Length of the bolts mm 60 70 70 79 110 40
Number of pumping move-ments for 25mm stroke
10 12 18 26 27 22
Support surface diameter mm 29 35 38 48 60 51
Baseplate diameter mm 114×72 132×76 152×92 165×106 130×140 183×129
Supplied as a standard with a coupling half with 3/8" NPT thread
Replaceable plunger
Exactly like flat cylinders, short-stroke cylinders are suitable for use in cramped
spaces.These devices are used where the standard cylinder is too large and the flat cylin-
der has too little lift.
WLLt
Strokemm
TypeOverall height
mmOil requirement
cm³Weight
kgrecommended
hand pumpReference no.
10 38.1 RSS101 88.9 55.8 2.7 P19 156027
20 44.5 RSS202 95.3 126.3 4.5 P19 156028
30 61.9 RSS302 117.5 259.1 6.7 P19 156029
50 60.3 RSS502 127.0 373.7 10.5 P59 156030
100 57.2 RSS1002 139.7 724.9 21.4 P159 156031
Larger lifting heights and working load limits on enquiry!
722011/12
Hydraulic pumps
Standard hand and foot pumps
For single-action cylinders
In this selection you will find the appropriate pump for each cylinder in our as-
sortment. When selecting, please note:
The oil volume of the pump must in general be larger than that of the cylinder.Single-stage pumps (P55) have only one pressure stage. Advantage: inexpensive
price, disadvantage: with a light load or idle stroke the cylinder extends only
slowly, since the quantity of oil is small for each pumping movement.Two-stage pumps have a low pressure and a high pressure stage. Advantage: in
the low pressure stage the quantity of oil for each pumping movement is larger.
Hence, the cylinder extends faster in the case of lighter loads or idle stroke. That
saves time.
Type Pressure stagesVol./stroke
stage 1cm³
Vol./stroke stage 2
cm³
Lever forcekg
Oil volumecm³
Usable oil quantity
cm³
ConnectionInch
Weightkg
Reference no.
P55 1 2.6 — 66 902 738 3/8-NPT 7.2 155975
P19 2 5 1.2 45 400 328 3/8-NPT 3.0 155976
P59 2 10.9 2.6 66 902 738 3/8-NPT 7.8 155977
P59F 2 9 2.1 55 902 738 3/8-NPT 6.4 218312
P159 2 42.6 2.6 64 2491 2245 3/8-NPT 11.9 155978
P460 2 120.5 4.6 41 9500 7539 3/8-NPT 24.9 155979
Additional pumps on enquiry!
Lightweight pumps with lower leverage force
For single-action cylinders
Compared to standard pumps, these pumps have a significantly
lower dead weight and a reduced leverage force with a larger oil
volume at the same time.
When selecting the right pump, the same applies as with the standard pumps –
see above!
Type Pressure stagesVol./stroke
stage 1cm³
Vol./stroke stage 2
cm³
Lever forcekg
Oil volumecm³
Usable oil quantity
cm³
ConnectionInch
Weightkg
Reference no.
P19L 2 4.1 0.9 37 475 443 3/8-NPT 2.3 218310
P59L 2 12 2.6 44 1131 1082 3/8-NPT 4.1 218311
Additional pumps on enquiry!
Pneumatic and electric pumps
For single-action cylinders
Pumps with pneumatic or electric drive are recommended for more convenience
when dealing frequently with hydraulics.
In this selection you will find the appropriate pump for each cylinder in our as-
sortment. When selecting, please note:Electric pump for 230 V / 50 Hz, with 3.1 m control cable
Air pressure required for pneumatic pumps: 3 to 8 bar
Type of drive Type Pressure stagesOil volume
cm³Usable oil quantity
cm³Connection
InchWeight
kgReference no.
Compressed air PA 6 1 1.7 1.6 3/8-NPT 6.3 155998
Compressed air PA462 2 9.5 9.4 3/8-NPT 27.2 218335
electric PE 172 – E 220 2 — 4.72 3/8-NPT 20.4 156000
Additional pneumatic and electric pumps on enquiry!
Pumps with battery/rechargeable battery drive on enquiry!
732011/12
Tra
nsp
ort
and
lif
ting
dev
ices
Hydraulic accessories
Hydraulic tubes and coupling halvesHigh-stability hydraulic tubes made of polyurethane. Safety factor 4. Operating
pressure to bursting pressure (700 bar: 2800 bar).
Complete with external thread at both ends
Inside diameter 6.4 mmA hydraulic tube and a coupling half for connection to the cylinder are required
for all pumps.
TypeLength
mReference no.
9765E 0.6 156001
9767E 1.8 156002
9769E 3.1 156003
9771E 6.1 156004
Other hose materials, e.g. rubber tubes or non-conductive tubes on enquiry!
Tubes with a larger diameter for faster oil return or faster lowering on enquiry!
Coupling halves including dust capfor high pressure hydraulics 700 bar
Type Reference no.
9798 156005
Manometer for load or pressure displayLoad or pressure display in bar
Manometer in diameters 63.5 or 101.6 mm
Insensitive to vibration and long life due to silicone filling
Red needle for optimum readability
Robust housing made of stainless steel
For the precise measurement of the load weight or the determination of the pres-
sure in the system. Enables, for example, tension or pressure with defined force.
The manometer is usually attached directly behind the pump. Only an additional adaptor piece is necessary. The manometer can also be attached directly in front
of the cylinder using the same adaptor.
TypeManometer
sizemm
Measuring rangebar
Scale main division
bar
Scale subdivi-sionbar
Reference no.
9040E 63.5 0 – 690 100 20 160984
9052E 100.0 0– 690 100 10 218319
Display in tonnes is also an option. Please enquire!
Connection fittings for manometersThe following fittings are required in order to integrate the manometer into the
hydraulics:
Connection directly after the pump, T-piece type 9670 or 9699Connection directly before the cylinder, T-piece type 9670
Connection in the tube pipe, T-piece type 9670 or 9699 and coupling 9680 as
well as a further hydraulic tube with external thread at each end