1 Transforming amorphous carbon into graphene by current- induced annealing Amelia Barreiro 1, † , ‡ ,* , Felix Börrnert 2, ‡ ,* , Stanislav M. Avdoshenko 3 , Bernd Rellinghaus 2 , Gi- anaurelio Cuniberti 3 , Mark H. Rümmeli 2,3 , Lieven M. K. Vandersypen 1 1 Kavli Institute of Nanoscience, Delft University of Technology, Lorentzweg 1, 2628 CJ Delft, The Netherlands. 2 IFW Dresden, Postfach 270116, 01171 Dresden, Germany. 3 TU Dresden, 01062 Dresden, Germany. KEYWORDS. graphene, graphene growth mechanisms, TEM, molecular dynamics, non-catalytic growth Supporting Information Placeholder ABSTRACT: We report on the catalyst-free growth of graphene from amorphous carbon (a-C) by current-induced an- nealing. This is a novel mechanism that we could witness by in-situ transmission electron microscopy and simulate with molecular dynamics calculations. We observe that small a-C clusters on a graphene substrate rearrange and crystallize into graphene patches due to the high temperatures involved and van-der-Waals interactions with the substrate. Fur- thermore, we report that in the presence of a-C, graphene can grow from the borders of holes in graphene, healing them out completely. These findings open up new avenues for bottom-up engineering of graphene-based devices. Graphene, a single atomic layer of carbon connected by sp 2 hybridized bonds, has attracted intense scientific in- terest since its recent discovery. 1 Much of the research on graphene has been directed towards the exploration of its novel electronic properties which open up new ave- nues to both exciting experiments in basic science 2-5 and electronic applications. 6 Further experiments and novel devices could be envisaged but remain to be demonstrat- ed due to technological challenges in fabrication such as the lack of precision for locating or growing graphene of a specific size on a substrate of choice. Whilst significant strides have been made in under- standing graphene synthesis, 7 the mechanisms behind growth remain highly debated. Graphene growth cannot be captured by a universal mechanism with specific routes and conditions but a variety of synthesis strategies and growth modes exist. The best-known mechanism is the use of metal catalysts whereby free carbon radicals are formed, carbon is dissolved in the catalyst, and final- ly precipitates at the surface. The free carbon radicals usually are supplied from a hydrocarbon feedstock, but there also are a few reports where the carbon feedstock is provided by a-C. 8-10 Another surface that can provide suitable sites for growth is a bulk oxide support without any metal catalyst present where the carbon precursor is supplied by a hy- drocarbon feedstock. 11-14 In the case of graphene growth from stable oxides as the support material, carbon disso- lution is unlikely and therefore the growth probably oc- curs through surface diffusion processes. Oxides without a metal catalyst can also be used for the growth of carbon nanotubes (CNTs). 15-16 The growth of sp 2 structures without a catalyst relies on a mechanism that largely remains to be understood. 17 Another example of such a process is the formation of CNTs on the cathode in the arc-discharge route which can occur without catalyst addition above 4000 ºC. 18-21 More recently, other growth routes without catalyst have emerged such as the formation of CNTs on graphitic sur- faces, 22,23 the substrate-free gas-phase synthesis of gra- phene sheets, 24 or the growth of graphene sheets by mi- crowave chemical vapour deposition (CVD). 25 Recently, the non-catalytic graphitization of a-C into polycrystalline graphene 26 and into additional shells on multi-walled (MW) CNTs 21,27,28 by current-induced an- nealing of graphene or of MWCNTs, respectively, has been reported. Moreover, catalyst-free crystallization of a-C nanowires led to the formation of tubular graphitic shells with nano-onions in their interior. 29 Unfortunate- ly, the quality of all these graphitized nanostructures was rather poor as compared to arc-discharge grown CNTs or mechanically exfoliated graphene, presumably because temperatures were insufficiently high (below 3000 ºC) to induce perfect graphitization. 21,30 In this Article we report on in-situ transmission elec- tron microscopy (TEM) and molecular dynamics (MD) studies of the structural changes that lead from a-C to graphene by catalyst-free growth via current-induced annealing. We observe that small a-C clusters on top of a graphene substrate rearrange and crystallize into gra-
18
Embed
Transforming amorphous carbon into graphene by current ... · KEYWORDS. graphene, graphene growth mechanisms, TEM, molecular dynamics, non-catalytic growth Supporting Information
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
Transforming amorphous carbon into graphene by current-
induced annealing
Amelia Barreiro1, †, ‡,*, Felix Börrnert2, ‡,*, Stanislav M. Avdoshenko3, Bernd Rellinghaus2, Gi-anaurelio Cuniberti3, Mark H. Rümmeli2,3, Lieven M. K. Vandersypen1
1 Kavli Institute of Nanoscience, Delft University of Technology, Lorentzweg 1, 2628 CJ Delft, The Netherlands. 2 IFW Dresden, Postfach 270116, 01171 Dresden, Germany. 3 TU Dresden, 01062 Dresden, Germany.
KEYWORDS. graphene, graphene growth mechanisms, TEM, molecular dynamics, non-catalytic growth
Supporting Information Placeholder
ABSTRACT: We report on the catalyst-free growth of graphene from amorphous carbon (a-C) by current-induced an-nealing. This is a novel mechanism that we could witness by in-situ transmission electron microscopy and simulate with molecular dynamics calculations. We observe that small a-C clusters on a graphene substrate rearrange and crystallize into graphene patches due to the high temperatures involved and van-der-Waals interactions with the substrate. Fur-thermore, we report that in the presence of a-C, graphene can grow from the borders of holes in graphene, healing them out completely. These findings open up new avenues for bottom-up engineering of graphene-based devices.
Graphene, a single atomic layer of carbon connected by sp2 hybridized bonds, has attracted intense scientific in-terest since its recent discovery.1 Much of the research on graphene has been directed towards the exploration of its novel electronic properties which open up new ave-nues to both exciting experiments in basic science2-5 and electronic applications.6 Further experiments and novel devices could be envisaged but remain to be demonstrat-ed due to technological challenges in fabrication such as the lack of precision for locating or growing graphene of a specific size on a substrate of choice.
Whilst significant strides have been made in under-standing graphene synthesis,7 the mechanisms behind growth remain highly debated. Graphene growth cannot be captured by a universal mechanism with specific routes and conditions but a variety of synthesis strategies and growth modes exist. The best-known mechanism is the use of metal catalysts whereby free carbon radicals are formed, carbon is dissolved in the catalyst, and final-ly precipitates at the surface. The free carbon radicals usually are supplied from a hydrocarbon feedstock, but there also are a few reports where the carbon feedstock is provided by a-C.8-10
Another surface that can provide suitable sites for growth is a bulk oxide support without any metal catalyst present where the carbon precursor is supplied by a hy-drocarbon feedstock.11-14 In the case of graphene growth from stable oxides as the support material, carbon disso-lution is unlikely and therefore the growth probably oc-curs through surface diffusion processes. Oxides without
a metal catalyst can also be used for the growth of carbon nanotubes (CNTs).15-16
The growth of sp2 structures without a catalyst relies on a mechanism that largely remains to be understood.17 Another example of such a process is the formation of CNTs on the cathode in the arc-discharge route which can occur without catalyst addition above 4000 ºC.18-21 More recently, other growth routes without catalyst have emerged such as the formation of CNTs on graphitic sur-faces,22,23 the substrate-free gas-phase synthesis of gra-phene sheets,24 or the growth of graphene sheets by mi-crowave chemical vapour deposition (CVD).25
Recently, the non-catalytic graphitization of a-C into polycrystalline graphene26 and into additional shells on multi-walled (MW) CNTs21,27,28 by current-induced an-nealing of graphene or of MWCNTs, respectively, has been reported. Moreover, catalyst-free crystallization of a-C nanowires led to the formation of tubular graphitic shells with nano-onions in their interior.29 Unfortunate-ly, the quality of all these graphitized nanostructures was rather poor as compared to arc-discharge grown CNTs or mechanically exfoliated graphene, presumably because temperatures were insufficiently high (below 3000 ºC) to induce perfect graphitization.21,30
In this Article we report on in-situ transmission elec-tron microscopy (TEM) and molecular dynamics (MD) studies of the structural changes that lead from a-C to graphene by catalyst-free growth via current-induced annealing. We observe that small a-C clusters on top of a graphene substrate rearrange and crystallize into gra-
2
phene patches. Due to the high temperatures involved and aided by the van der Waals interactions with the substrate, large grain sizes and even crystalline graphene are obtained. Furthermore, in the presence of a-C, gra-phene can grow from the borders of holes and form a seamless graphene sheet.
Chips with single-layer and few-layer graphene flakes supported by metal contacts were mounted on a custom-built sample holder for TEM with electric terminals, ena-bling simultaneous TEM imaging and electrical meas-urements. For imaging, a FEI Titan3 80–300 transmis-sion electron microscope with a CEOS third-order spher-ical aberration corrector for the objective lens was used. It was operated at an acceleration voltage of 80 kV to reduce knock-on damage. All studies were conducted at room temperature with a pressure of approx. 10-7 mbar. The graphene device fabrication and measurement pro-cedures are described in detail in ref. 31. In brief, a gra-phene flake is transferred onto Cr/Au electrodes that are freely suspended over an opening in a Si/SiO2 wafer. The device is voltage biased and the current is measured. In total, we measured 15 devices, with spacings between the electrodes between 1 and 20 µm.
We perform in-situ current-induced annealing of the suspended graphene devices by taking the samples to the high bias regime, specifically up to 2 - 3 V.32 Tempera-tures as high as 2000 ˚C,26,33 or even 3000 ˚C,29 were estimated to be reached due to Joule heating. As a result, contaminants from fabrication are removed,32 and we observe that we obtain atomically clean graphene devic-es, as can be resolved from TEM imaging. After the cur-rent annealing process, the bias is taken back to 0 V and the samples cool down. During the TEM imaging of the cold samples, we observe a-C deposition on the previous-ly clean graphene surfaces,34 see figure 1. The carbon source can originate from the decomposition of hydro-carbons in the TEM column and/or from organic impuri-ties adsorbed on the chip, the chip carrier and the sample holder. The regions where the a-C preferentially deposits are the edges of the individual layers in few layer gra-phene flakes, edges and other defects, fig. 1.35 Amor-phisation of the graphene sheet because of disorder in-troduced by the electron beam is unlikely at an accelera-tion voltage of 80 keV, which is below the “knock-on” damage threshold of carbon nanostructures.36 Thus gra-phene sheets remain stable and defect free in clean re-gions.37 However, holes can form in contaminated areas by beam-driven chemical modifications with contami-nants and adsorbates at energies below the knock-on threshold.38 These holes seem to concentrate around edges and other defects, fig. 1 b, c.35 Interestingly, during the current-annealing process itself, we never observe deposition of a-C. Presumably, hydrocarbon precursors for a-C formation evaporate before being able to reach the graphene flake due to the high temperatures and de-posit on colder areas around the hot graphene.
After deposition of a-C on the previously atomically clean graphene surfaces, the samples are brought back once more to the high bias regime and current-annealed again. We proceed by stepwise increasing the voltage, waiting for changes to occur and then slowly further in-crease the bias voltage. Interestingly, during this process
we observe that it is not possible to evaporate the a-C but instead it gradually transforms into graphene patches. We have observed the transformation of a-C to graphene by current-induced annealing on 15 of 15 samples where a-C had been intentionally deposited by the TEM beam. Fig. 2 illustrates the evolution of the process from amor-phous matter to crystalline graphene.
Due to the nature of our in-situ TEM experiments, we can unequivocally testify to the circumstances during growth by performing atomic resolution imaging. Small a-C clusters rearrange and crystallize due to the high temperatures reached during current annealing without the involvement of any catalyst. Before reaching temper-atures high enough to evaporate the a-C, it can rearrange through a phase of glasslike carbon into high-quality graphene, see figure 2.
The supporting information (SI) contains low magnifi-cation TEM images (figure S3) and a video (movie S1) of a different device where an overview can be obtained regarding the gradual transformation of a-C to graphene by current-induced annealing.
Based on high resolution (HR) TEM (see Fig. 3) we were able to confirm that indeed the newly grown patch-es are graphene. From the corresponding Fourier trans-form (FT) in Fig. 3 (b) we can obtain the typical lattice parameter of graphene and the orientation of the newly grown layer which is rotated by 22 degrees with respect to the substrate. These patches can reach up to 100 nm x 100 nm in size. The fact that we obtain a clear FT signal from an overlayer of an area of approx. 30 nm2 suggests that the graphene grown is not disordered and has a “long range order”, i.e. consists of a single grain.
In order to shed light on the catalyst-free transfor-mation mechanism of a-C into graphene and to explore the role of the graphene substrate, we have performed molecular dynamics simulations of a perfect graphene substrate and four a-C clusters of 1 nm diameter on top at a distance of ~ 3.5 Å (Fig. 4); for more details see [SOM]. During the MD simulations, the graphene sub-strate and the four a-C clusters on top are subject to stepwise increasing temperatures. In particular we chose 300, 600, 1200 and 1800 K. This scenario resembles well our experimental procedure. In the experiments, a para-bolic thermal gradient is present because the heat is only evacuated through the electrodes and the hottest spot is close to the middle. In the theoretical modeling we will assume a constant temperature, which is a reasonable approximation for the small windows used in the simula-tions, especially at the hottest spot where the thermal gradient is small.
Upon increasing temperature, the a-C starts trans-forming, goes through a glasslike phase at 600 - 1200 K and finally reaches a graphene structure at 1800 K, see figure 4 (b).35 The structure formed is flat and is located 3.5 Å above the initial graphene template. Nevertheless, big holes are still present because there was not enough carbon precursor available to grow graphene over the whole area of the graphene template. Upon further addi-tion of a-C at 1800 K the graphene structure grows and, progressively, defects are healed out (Fig. 4c). Indeed, some areas display defect-free graphene such as in figure 4d. The remaining holes and defects could be healed by
3
further addition of a-C and a longer annealing time but would lead to excessively long calculation times. In mov-ie S2, showing the transformation of a-C to graphene, it can be observed that only at the last stage of the growth process when the graphene precursor flakes merge into a bigger unit, they are immobilized on the surface due to energy gain given by the π-π coupling, suggesting that any atomically smooth substrate could serve as a tem-plate.
Recently, similar MD simulations modeled the synthe-sis of fullerenes.39-41 An important difference between those simulations and ours is that in our case there is a graphene substrate while the fullerene synthesis was ob-tained in a substrate free model. Independently on the initial geometry and velocity of the a-C, at the end of the MD runs, graphene is reproducibly formed on top of the graphene template. Although the substrate is only weakly coupled to the a-C, it apparently strongly influences the transformation of the nano-structure on top of it and prevents the formation of fullerene-like structures, demonstrating its influence on the formation of gra-phene. Experimental evidence that confirms that the graphene template is only weakly coupled to a-C is found by the fact that the newly grown graphene patch is rotat-ed with respect to the initial one, see figure 3. Once more, these results suggest that, in a more general picture, our graphene growth method is universal for atomically smooth template-supported processes such as graphene, hBN or other two-dimensional layered materials such as MoS2. Indeed, a similar “substrate effect” has recently been recently reported for the growth of graphene on Ni,42 and it was possible to grow graphene on hBN by CVD,43 further supporting the universality of this growth method on atomically flat 2D systems.
Another interesting finding is that in the presence of a-C at a high bias it is possible to repair holes in the gra-phene lattice. In Fig. 5 we observe that holes formed by the reaction of contaminants with graphene due to the electron beam,38 are self-repaired by growing new gra-phene covering the holes. Recently, it was found that vacancies in a graphene lattice can be quickly reoccupied by C ad-atoms and graphene can recover its crystallinity. This repairing mechanism works best at temperatures above 600 °C and was attributed to lattice reconstruc-tions.34 Healing of multivacancies in carbon nanotubes with up to 20 missing atoms can also be achieved with lattice reconstructions due to the TEM beam.44 The holes in our graphene lattice are much bigger and can have diameters up to 5 nm.35 Indeed, figure 6 suggests that the holes are closing step by step, presumably by the for-mation of new bonds with carbon radicals originating from the a-C. In this sense, the healing mechanism of the holes can be understood as substrate-free growth starting from the borders of holes in the graphene lattice by car-bon atom addition to the reactive dangling bonds at the edges.
Low magnification TEM images (figure S4) and a video (movie S3) of a different device to obtain an overview regarding the gradual healing of holes in graphene in the presence of a-C by current-induced annealing can be found in the supporting information (SI).
To gain further insight into this experimental observa-tion, we performed MD simulations. We create a hole with a 1 nm radius in an ideal graphene flake and place 3 a-C clusters (of 1 nm3 size each) on top of it, see figure 6. Then we heat our system to 1800 K. First, long fibers and big polyedres (C8-10) are formed across the hole. After further annealing, the hole is healed completely. For sev-eral independent runs with different initial structural and velocity conditions it always took 25 - 30 ps to com-pletely heal the hole. The newly grown graphene contains at least one Stone-Wales defect (two pentagons (C5) and two heptagons (C7) forming a double pair),35 which would heal out if significantly increasing the simulation time. This process of graphene growing in a hole until it heals out completely can be seen in movie S4.
Interestingly, running the same MD simulations at temperatures below 600 K instead of at 1800 K does not yield healed out holes, suggesting that high temperatures are required for repairing holes and growing graphene in them. Effective changes in a reasonable timeframe for the simulations (around 10 ps) only take place above 600 K. Due to the high temperatures reached during current annealing, untangled and non-saturated bonds from the a-C diffuse on the graphene and act as a source of radi-cals. They react with the dangling bonds at the edge of holes, gradually healing them out by growing a new gra-phene lattice.
The speed of the transformation from a-C to graphene or the growth of graphene in holes in our MD simula-tions can be markedly fast, down to about 50 ps. Howev-er, the time elapsed for the transformation of a-C to gra-phene observed experimentally takes up to 1 - 15 minutes. The large difference in velocity between the experiments and simulations is attributed to the differ-ence in the system dimensions. Apart from that, experi-ments were done as slowly as possible to prevent bring-ing the sample to an excessively high bias where the transformation would occur quicker but the risk of com-plete electrical breakdown of the sample is larger. Be-cause our calculation capabilities do not allow timescales of minutes to be reached, a direct comparison of the timescale between experiments and simulations cannot be made, although the mechanism responsible for the growth appear to be similar.
In conclusion, our in situ real-time TEM observations correlated with MD simulations demonstrate that a di-rect transformation of a-C to flat graphene sheets is pos-sible. Small a-C clusters rearrange and crystallize into graphene at high temperatures on a graphene substrate or from the edges of holes. This finding opens up new avenues for engineering novel graphene-based devices such as thermal motors where a cargo could be trans-ported on top of a graphene patch,45 or for graphene-based optoelectronic devices with monolayer-bilayer junctions.46 Clusters of a-C could be deposited on speci-fied locations on top of graphene and then be trans-formed to additional graphene patches in-situ by a fur-ther (current-)annealing step. In a more general picture, our graphene growth method seems to be universal for atomically smooth template-supported processes such as graphene, hBN or other strongly layered 2D crystals such as MoS2 or NbSe2. Indeed, it has already been demon-
4
strated that it is possible to grow graphene by CVD on monolayers of hBN.43 Importantly, graphene on hBN devices holds great promise for novel experiments and applications due to graphene’s improved mobility.47,48 Indeed, the substrate strongly influences the quality of the graphene; mobilities up to 80.000 cm2/V-1s-1 and
35.000 cm2/V-1s-1 of mechanically cleaved graphene and CVD grown graphene transferred onto hBN, respectively, have been reported, several times larger than the mobili-ties of graphene on SiO2.47,49 Transforming a-C to gra-phene could open up new avenues for novel devices con-sisting of graphene on top of 2D materials of choice.
FIGURES.
Figure 1. TEM images of the stepwise deposition of a-C on an initially clean graphene sheet due to imaging. The scale bar is 20 nm. (a) Preferential deposition at edges of other graphene layers. (b) Formation of holes (marked with arrows) and further deposition of a-C. (c) Growth of holes (marked with arrows) and almost complete coverage of a-C on the graphene template.
Figure 2. Aberration corrected HR-TEM images of the stepwise transformation of a-C into graphene patches by means of current annealing at 3.32 V, 0.55 mA. (a) a-C on graphene. The scale bar is 2 nm. (b,c) Gradual crystalliza-tion of the a-C through a glass-like phase. (c) Transfor-mation into highly ordered graphene patches. The time elapsed between the four frames is 22 minutes.
Figure 3. (a) Aberration corrected HR-TEM image of the graphene support (top) and a graphene patch grown on top of it (bottom) from a-C by means of current annealing. The scale bar is 2 nm. The contrast of the micrograph was enhanced through Wiener filtering to suppress noise. (b) FT of the initial graphene layer in the upper part of the TEM image marked by a square. (c) FT of the whole mi-crograph containing the graphene support layer and the graphene patch grown on top (circles), which are rotated with respect to each other by 22º.
5
Figure 4. Molecular dynamics simulations of the stepwise transformation of a-C to graphene. (a) Initial 4 a-C clusters on top of a graphene unit cell marked by a yellow square. (b) Intermediate stage after annealing at 1800 K. (c) Struc-tural shape after further a-C addition at 1800 K. The time elapsed between each frame is ~50 ps (see text for details). (d) Zoom in into the red square in panel (c) displaying a perfect graphene region without defects.
Figure 5. Aberration corrected HR-TEM images of the gradual healing of a hole in the graphene lattice by means of current annealing of graphene in the presence of a-C at 2.75 V, 2.2 mA. The arrows point to the initial hole (a), that gradually gets smaller (b) until it completely heals out (c). The scale bar is 2 nm. The time elapsed between the three frames is 30 s.
Figure 6. Molecular dynamics simulations at 1800 K de-scribing the hole healing process. a-C is represented by the semi-transparent spheres. (a) Initial configuration display-ing a hole in the graphene lattice. (b) Intermediate state of the structural transformation. (c) Repaired hole.
a
c
b
6
ASSOCIATED CONTENT
Supporting Information. Details of the experimental methods; additional images and discussion regarding the preferential deposition of a-C on the edges of individual layers and defects in few layer graphene; effect of the 80 keV beam; additional TEM images of the transformation of a-C to graphene and graphene growth in holes by current-induced annealing; detailed information of our molecular dynamics simulations. Movie S1: Video transforming a-C to graphene, 6 times quicker than in real time. Movie S2: Video of the MD calculations regarding a-C to graphene. Movie S3: Video transforming a-C to graphene and healing of holes, 5 times quicker than in real time. Movie S4: Video of the MD calculation of healing a hole. This material is available free of charge via the Internet at http://pubs.acs.org.
† Department of Physics, Columbia University, New York, New York 10027, USA.
Author Contributions
‡These authors contributed equally.
Funding Sources
Financial support was obtained from the Dutch Founda-tion for Fundamental Research on Matter (FOM), Agència de Gestió d´Ajuts Universitaris i de Recerca de la Generali-tat de Catalunya (2010_BP_A_00301), DFG (RU1540/8-1), EU (ECEMP) and the Freistaat Sachsen. Notes Any additional relevant notes should be placed here.
ACKNOWLEDGMENT
We gratefully acknowledge M. Rudneva and H. Zandber-gen for help in the early stages of the experiment, G. F. Schneider for help with graphene transfer and M. Zuid-dam for help with the deep reactive ion etching process. Financial support was obtained from the Dutch Founda-tion for Fundamental Research on Matter (FOM), Agència de Gestió d´Ajuts Universitaris i de Recerca de la Generali-tat de Catalunya (2010_BP_A_00301), DFG (RU1540/8-1), EU (ECEMP) and the Freistaat Sachsen.
[1] Novoselov, K. S.; Jiang, D.; Schedin, F.; Booth, T. J.; Khotkevich, V. V.; Morozov, S. V.; Geim, A. K. Proc. Natl Acad. Sci. USA 2005, 102, 10451–10453. [2] Zhang, Y.; Tan, Y.-W.; Stormer, H. L.; Kim, P. Nature
2005, 438, 201-204. [3] Novoselov, K. S.; Geim, A. K.; Morozov, S. V.; Jiang, D.;
Katsnelson, M. I.; Grigorieva, I. V.; Dubonos, S. V.; Firsov. A. A. Nature 2005, 438, 197-200. [4] Bolotin, K. I.; Ghahari, F.; Shulman, M. D.; Stormer, H.
L.; Kim, P. Nature 2009, 462, 196-199. [5] Du, X.; Skachko, I.; Duerr, F.; Luican, A.; Andrei, E. Y.
[29] Huang, J. Y.; Chen, S.; Ren, Z. F.; Chen, G.; Dressel-haus M. S. NanoLetters 2006, 6, 1699-175. [30] Physics of Graphite; Kelly, B. T.; Applied Science Pub-
S. J. Am. Chem. Soc. 2011, 133, 18837–18842. [43] Usachov, D.; Adamchuk, V. K.; Haberer, D.; Grüneis,
A.; Sachdev, H.; Preobrajenski, A. B.; Laubschat, C.; Vyalikh, D. V. Phys. Rev. B 2010, 82, 075415.
[44] Börrnert, F.; Gorantla, S.; Bachmatiuk, A.; Warner, J. H.; Ibrahim, I.; Thomas, J.; Gemming, T.; Eckert, J.; Cuniber-ti, G.; Büchner, B.; Rümmeli, M. H. Phys. Rev. B 2010, 81, 201401R. [45] Barreiro, A.; Rurali, R.; Hernandez, E. R.; Moser, J.;
Pichler, T.; Forro, L.; Bachtold, A. Science 2008, 320, 775–778. [46] Xu, X.; Gabor, N. M.; Alden, J. S., van der Zande, A.
M.; McEuen P. L. Nano Lett. 2010, 10, 562-566. [47] Dean, C. R.; Young, A. F.; Meric, I.; Lee, C.; Wang, L.;
Sorgenfrei, S.; Watanabe, K.; Taniguchi, T.; Kim, P.; Shepard, K. L.; Hone, J. Nature Nanotechnology 2010, 5, 722-726. [48] L. A. Ponomarenko, A. K. Geim, A. A. Zhukov, R. Jalil,
S. V. Morozov, K. S. Novoselov, I. V. Grigorieva, E. H. Hill, V. V. Cheianov, V. I. Fal’ko, K. Watanabe, T. Taniguchi, R. V. Gorbachev. Nature Physics 2011, 7, 958-961. [49] Gannett, W.; Regan, W.; Watanabe, K.; Taniguchi, T.;
Crommie, M. F.; Zettl, A. Appl. Phys. Lett. 2011, 98, 242105.
TOC.
8
Supporting Information
Transforming amorphous carbon into graphene by current-
induced annealing
Amelia Barreiro1, †, ‡,*, Felix Börrnert2, ‡,*, Stanislav M. Avdoshenko3, Bernd Rellinghaus2, Gi-anaurelio Cuniberti3, Mark H. Rümmeli2,3, Lieven M. K. Vandersypen1
1 Kavli Institute of Nanoscience, Delft University of Technology, Lorentzweg 1, 2628 CJ Delft, The Netherlands. 2 IFW Dresden, Postfach 270116, 01171 Dresden, Germany. 3 TU Dresden, 01062 Dresden, Germany.