To buy: Contact Sylvane at 800-934-9194 or visit www ... · Air Washer must be installed and operated on an even surface. I Vibrations and noise can occur on soft or non-flat surfaces.

WINIX Korea 35-1, Unjung-Dong, Bundang-gu, Seongnam-si, 463-440, South Koreawww.winixcorp.com e-Mail [email protected] Tel +82.31.701.1173(4574)

WINIX Inc 120 Prairie Lake Road, Unit E East Dundee, lllinois 60118www.winixinc.com e-Mail [email protected] Tel +1.847.551.9900

WINIX Europe 14 Cours de l'Intendance, 33000 Bordeaux, Francewww.winixeu.com e-Mail [email protected] Tel +33.556.448.572

Thank you for purchasing this WINIX product

This marking shown on the product or its literature, indicates that it should notbe disposed with other household wastes at the end of its working life. Toprevent possible harm to the environment or human health from uncontrolledwaste disposal, please separate this from other types of wastes and recycle itresponsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased thisproduct, or their local government office, for details of where and how they can take thisitem for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of thepurchase contract. This product should not be mixed with other commercial wastes fordisposal.

Sep. 2012

To buy: Contact Sylvane at 800-934-9194 or visit www.sylvane.comFor product support: Contact Winix at 877.699.4649

1 2

Intro

du

ction

Installatio

nO

peratio

nM

ainten

ance

TABLE OF CONTENTS

FEATURES 1

Read all instruction 1

INTRODUCTION 3

SAFETY INSTRUCTIONS 3

PRODUCT AND PARTS VIEWS 7

PRODUCT INSTALLATION 9

SETTING UP YOUR AIR WASHER 9

PRODUCT OPERATION 10

BEFORE TURNING ON 10

AUTO MODE 12

SLEEP MODE 13

ADJUSTING FAN SPEED 13

EMPTYING WATER TANK 14

CARE AND MAINTENANCE 15

OUTER SURFACE 15

CLEANING PRE-FILTER 15

CLEANING ANTIMICROBIAL DISK AND WATER BUCKET 16

CLEANING THE UNIT 17

FAQs & TROUBLESHOOTING 19

SPECIFICATIONS 21

FEATURES

2-in-1 Air Treatment The Winix FresHome Air Washergently and safely captures odorsand impurities while gentlyhumidifying the air.

CleancelTM Anti-Microbial CoatingThe Winix Air Washer is treated withCleancelTM to prevent the growth ofodor causing bacteria and microbeson the cleanable humidifyingcollection discs.

Auto Sleep ModeThe Winix Air Washer willautomatically dim the displaylights and operate at lowest speedto not disturb sleep.

Auto ModeA sensor continually monitors theenvironment and adjusts theperformance for optimal humiditylevels.

Auto Shut-OffWINIX Air Washer shuts offautomatically when the waterbucket is low.

Plasma WaveTM TechnologyAttacks pollutants at the molecularlevel to neutralize viruses, bacteria,chemical vapors, odors and gases inthe air leaving the Air Washer.

Read all instruction: Important Safeguards

When using electrical appliances, especially when children are present basic safetyprecautions should always have followed, including the following:

1. Always have water in the water tank when operating unit.

2. Use only clean, cool tap water to fill tank.

3. Use only 100~120V AC outlet. As with any electrical device, plug and unplug unit withdry hands only. Turn unit off prior to unplugging it. Unplug unit when not in use andbefore you clean or move the unit.

4. This unit shuts off automatically when water tank is empty.

5. Never operate unit with a damaged coed or plug. Keep cord straight.

6. Always place unit on an elevated (at least one(1)foot off the ground), flat, level surfaceaway from direct sunlight. Keep cord away from heated surface and areas where it couldbe walked on or tripped over. Do not place on objects that are not resistant to waterdamage from spillage or moisture.

7. Do not titt or tip unit or attempt to empty or fill it while it is operating.

8. The unit should not be left unattended in closed rooms as air could become saturatedand leave condensation on walls or furniture. Always leave room door partially open.

9. Do not tilt or tip unit or attempt to empty or fill while it is operating.

10. Replace demineralization cartridge every 2~3 months or more frequently as needed.

▶Power Cord Warning

43

INTRODUCTION

DON'T unplug the unit by pulling on itspower cord.

DON'T touch the plug with wet hands.

DON'T bend or place heavy object(s) onthe power cord.

DON'T replace or modify the power cord.If the power cord/plug is damaged, it must bereplaced by the manufacturer or a qualifiedtechnician.

Follow these instructions to avoid any risk ofpersonal injury, property damage, electricalshocks or fire hazards.

WARNING

Failure to follow the safety instructions canlead to personal injury or property damage.

NOTICE

WARNING / NOTICE DIRECTION

PROHIBITED

DO NOT DISASSEMBLE

Intro

du

ction

WARNING:SAFETY INSTRUCTIONS Warning ▶Power

Warning ▶Operation

DO connect the power cordto outlets with a groundconnection ONLY.

DO unplug air washer whennot in use to save energyconsumption.

DON'T plug power cordinto loose or damagedelectrical outlet.(Can lead to overheating orelectrical shock.)

DO NOT attempt to repair,alter or disassemble theair washer.

DON'T operate the airwasher if standing water ispresent.

DON'T operate air washeron an uneven surface.

DON'T pour water into thetop of the air washer, onlyplace in water tank asdirected.

DON'T operate air washer near flammable materials.

Must Follow

Ground connection protectingfrom electrical shock

Note ▶Operation

65

Note ▶Power

Note ▶Operation

DON'T disconnect thepower cord duringoperation.

DO unplug the applianceduring filling and cleaning.

DO unplug the unit andcontact your service dealerif any irregular noise orsmoke occurs.

DO use the air washer afterassembling the AntimicrobialDisk.

DON'T insert ANYTHINGinto the air inlet or outlet.

DON'T place theair washer near a heatsource.

DON'T place hands orbody parts near the airoutlet during operation.

DON'T place the air washernear curtains or othermaterials that can cover thevents of the unit.

DON'T strike or drop theair washer.

DON'T allow children toplay on or near the airwasher.

DON'T use hot water in thewater tank.

DO clean Antimicrobial diskregularly with warm tapwater and allow to air dry.Discs are top-rack dishwasher safe.Follow directions in the Care andMaintenance section.

DON'T spray flammableliquids or gases into the unit.

DON'T place air washernear your head when yousleep.

DO move the top coverand water bucket of theunit separately whenmoving air washer.

DON'T use flammable material(such as benzene or alcohol) to cleanthe air washer.

DON'T cover the top of the air washerduring operation.

※ This appliance intended for adult use only.

DO NOT spray liquids directly intoair washer during cleaning.

DON'T install the unit in direct sunlightor near inverter lighting or automaticsensor lights.

Intro

du

ction

87

Display Panel

Power / Function Button

Disk Assembly Handle

Air outlet

CleancelTM Antimicrobial Disks

Water Bucket

Power Cord

Air Inlet

Power Button

Current Humidity Level

Fan/Disk Speed

PlasmaWaveTM

On/Off Indicator

Low Water Indicator

Function Button:Fan/Disk Speed (LOW MEDIUM

HIGH), Sleep Mode, Auto Mode.

Front Display Panel and Controls

Back

Intro

du

ction

PRODUCT AND PARTS VIEWS

Top Cover

Pre-Filter

Light Sensor

Sleep Mode Indicator

Auto Mode Indicator

9 10

PRODUCT INSTALLATION PRODUCT OPERATION

Do not install the unit under direct sunlight.Long Exposure to direct sunlight can cause defects.

Air Washer must be installed and operated on an even surface.Vibrations and noise can occur on soft or non-flat surfaces.

Products must be installed approximately 4 inches away from the wall and 15 inches from other electronic appliances.

Before operating the air washer, remove any plastic bags and polyfoams fromoutside and inside of the unit.

SPACE SELECTION & INSTALLATIONFor better performance and longer product life, please select an adequate space toinstall the unit.

Installatio

nO

peratio

n

❷ Fill the water tank with cool tap waterup to the indicator line on inside of thewater tank. For optimal performance donot overfill.

❸ Replace the top section of the air cleaner.Make sure that it is seated properly andlines up correctly.

❶ Lift and remove top section of theair washer to open.

Water Line

Cautions ▶Make sure to unplug the power cord before filling the water tank.

▶Hard water may cause operation defects. Please use filtered water if necessary.

▶Use caution when moving air washer with a full water tank, as it will be heavy.

SETTING UP YOUR AIR WASHER BEFORE TURNING ON

1211

Op

eration

❺ Push POWER button.

❹ Plug the power cord into a power outlet.

❻ The air washer will start in Auto Modeand the PlasmaWaveTM function will beON. If the Low Water Indicator is on,refill the water bucket.

AUTO MODE

❶ Push FUNCTION button to select Automode.

The FUNCTION button will cycle the unit betweenthe following: LOW MEDIUM HIGH SLEEP MODE AUTO MODE.

❷ AUTO Mode Indicator will illuminate.Fan and disk speed will automatically adjust,according to chart below, for optimal humiditylevel of around 50%.

❸ Push the POWER button to turn off.All lights will be off.

Fan speedHumidity RangeMore than 60% LOW

MEDIUMHIGH

From 50% to 59%Less than 50%

1413

Manual Sleep Mode

❶ Push FUNCTION button.

❷ Select Sleep Mode.(Indicator light will illuminate)

❸ Sleep Mode will dim the display lights.(Fan speed :low)

Auto Sleep Mode

● When in Auto Mode (see previoussection), the light sensor will detect thelight in the room and will turn on SleepMode when external light sources aredimmed.

Main

tenan

ce

SLEEP MODE EMPTYING WATER TANK

● Push FUNCTION button to changeFan/Disk speed.

The FUNCTION button will cycle the unit betweenthe following: LOW MEDIUM HIGHSLEEP MODE AUTO MODE

❷ Remove the use water left in the watertank and dispose of in an appropriatemanner. Refill water tank. (do not fillpast indicator line as directed)

❸ Replace the disk assembly. Lay handledown flush with water tank. Carefullyreplace top section of air washer andassure proper alignment.

❶ Remove the top cover the unit. Lifet thedisk assembly by the handle and carefullyremove it.

Cautions ▶Allows unplug the power cord when removing or adding water to the water tank.

▶If the air washer has not been used for an extended period of time, use fresh waterto avoid performance issues.

Adjust Fan/Disk Speed

15 16

Main

tenan

ce

❷ Clean the inside of water bucket with asoft cloth and mild detergent.

Clean the water bucket every week to preventthe growth of mold, germs, and bacteria.Refill the bucket with clean tap water.

❸ Place CleancelTM Antimicrobial Disk backinto the bucket aligning with groovesand with handle laid flat.

❶ Clean Antimicrobial Discs with warmtap water.

Cautions ▶Before cleaning air washer, unplug the power cord.

▶Don’t use flammable materials such as benzene and alcohol to clean air washer.

▶If the air washer has not been used for more than two days, unplug the power cordand refill the water bucket with new water.

▶Always clean the antimicrobial discs and water bucket of the unit has not beenused for an extended period of time to prevent contamination.

CARE AND MAINTENANCE

❷ Rinse pre-filter clean with warm tapwater.

❸ Use tabs and slide pre-filter back intooriginal position.

❶ Use the tab on each side of the prefilterand gently pull up and out from bothsides.

● Clean the outside of the unit with a softcloth and mild detergent. Wipe cleanwith a dry cloth.

OUTER SURFACE CLEANING ANTIMICROBIAL DISK AND WATER BUCKET

CLEANING PRE-FILTER

17 18

Main

tenan

ce

❺ Wash the fan with warm water. Use a soft cloth to wipe dry.

❻ Reassemble in reverse order aftercleaning.

❹ Gently clean the inside of the housingwith a soft cloth or vacuum cleanerattachment.

Cautions ▶Only the fan should be washed with water.

❷ Open venting guides until you hearthem 'click'

❸ Remove the fan cover by turning thelocking nut clockwise and lifting thefan up.

❶ Remove the top cover and place itupside down on an even surface.

CLEANING THE UNIT

2019

Symptom Check if: Remedy:

▶Water is too cold or icy.

▶Fan speed is on low level.

▶Use 68℉ to 77℉temperature water.

▶Change to highfan speed.

▶Remove the film.

▶Use FUNCTION button toturn off Sleep Mode.

Low air flow.

Display panel light istoo dark.

▶Protective film is still on.

▶Manual Sleep Mode is on.

▶Auto Sleep Mode is on.

Unpleasant odors arepresent.

▶Air Washer is being usedwhere strong odorsand/or dust are present.

▶Replace the water in thewater tank and changewater more frequently.

Main

tenan

ce

FAQs & TroubleshootingCheck if you can resolve issues before calling customer service.

Symptom Check if: Remedy:

▶Power cord is plugged in.

▶Low Water Indicator lightis on

▶Top and bottom sectionsare aligned.

▶Plug the power cord in.

▶Fill the the water tank.

▶Make sure the top andbottom of the air washerare lined up correctly.

Air washer does notturn on.

▶Power cord is plugged in.

▶Auto Mode Indicator is on.

▶Sensor is obstructed.

▶Plug the power cord in.

▶Push FUNCTION buttonto select Auto Mode.

▶Clean the sensor surface

Auto Mode is notworking.

▶The unit is located on anuneven surface.

▶Move to even surface.Vibrates or makes a lotof noise.

2221

NotesSPECIFICATIONS

Model No.

Power Supply

Power Consumption

Humidifying Capacity

For rooms up to

Tank(Max/Full)

Weight

Dimension(WXDXH)

230V / 50Hz

10ℓ/ 8ℓ

330×330×420(mm)

400CC / Hour (20℃/30%)

6.5㎏

17W

AW107 (EU)

110V / 60Hz

2.64gal/2.11gal

600 sq. ft.600 sq. ft.

12.9In×12.9In×16.5In

0.105gal / hour(33.8℉/30%)

14.3Ib

17W

AW107 (USA)