TEST MEASUREMENT...Test Equipment CABAC Test Equipment Ideal for professional use in industrial, electrical applications, field environments, laboratory or workshop applications there’s

133 122 | cabac.com.auREV1 / October’20

TESTMEASUREMENT

2 cabac.com.au133 122

1. CAT IThis covers measurements performed on circuits not connected directly to the mains. Surges in an electronic device e.g. a PCB inside a photocopier, may have some electronic ripple.2. CAT IIFor measurements on circuits connected directly to the low voltage installation e.g an appliance. Appliances such as power tools or household appliances and the electrical cord may have low surges from a motor for example.3. CAT IIIFor measurements of the circuit in a building installation i.e. plugs and sockets, distribution boards, lighting circuits, underground cable, boreholes connected by underground cable, etc. e.g. dissipated lightning surges.4. CAT IVFor measurements at the source of an electrical installation. This covers outside supply lines, overhead lines and the main board connected to overhead lines. These electrical circuits are exposed to substantial surges such as lightning.

Handy Info (IEC61010-1 2010)Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements. Explanation of categories listed in clause 6.7.4

The table on the right indicates the applied voltages (BIL) of an impulse generator. The generator shall produce an open circuit voltage waveform of 1,2/50ms.

Impulse Withstand Voltages for the IEC61010 Categories

Nominal Voltages Voltage Transients

Phase toNeutral Voltage*

Transient stresses estimated within the installation without any over-voltage limiting devices

CATII CATIII CATIV50 500 800 1500

100 800 1500 2500

150 1500 2500 4000

300 2500 4000 6000

600 4000 6000 8000

1000 6000 8000 12000

Output Impedance of Impulse Generator 12Ω 2Ω 2Ω

Loop Impedance is the sum of impedances in a circuit measured from an outlet point to the supply transformer via active or neutral or earth and the respective return in the loop. PSC is the prospective short circuit current that the loop will carry due to the resistance and applied voltage.

The T2726 Loop Impedance Tester will display in scrolling order, the line voltage, the sum of and individual impedances and the prospective short circuit current (PSC) in loops Active/Neutral and Active/Earth. The instrument calculates the PSC using the recorded voltages and measured impedances. To obtain accurate milliohm values the instrument uses a high test current, which will trip the RCD. The RCD should be by-passed and the load on the circuit minimized before the test is done. Instruments that do not trip the RCD use test currents below 20mA and are not as accurate as when using a higher current test. Determining the PSC is useful to determine the maximum load protection on a circuit e.g. a class C circuit breaker needs to trip at 7.5 times its rated current and the circuit must be able to carry it.

A loop impedance meter will test neutral integrity according to AS4741 as per Appendix B Method B3.

Drawing 1 – Physical Layout of Supply Loops

Meter Board

Transformer

AN

E

Pole Fuse

Active

Neutral

MENLINK

Drawing 2 – Earth Fault Loop

Notes on Loop Impedance

3cabac.com.au 133 122

Triple R Service & Calibration Policy

Certificate of Quality

CABAC confirms herein that the unit you have purchased has been calibrated, during

the manufacturing process, in compliance with the test procedures defined by CABAC

and the manufacturer.

All CABAC procedures are monitored on a permanent basis in compliance with

ISO 9000 Quality Management Standards.

In addition CABAC confirms that all test equipment and instruments used during the

calibration process are subject to constant control. All test equipment and instruments

used are calibrated at determined intervals, using reference equipment, which has

been calibrated in compliance with (and traceable to) the calibration standards of

international laboratories and the country of manufacturer’s national standards.

The factory settings are valid for a period of one year from the date of purchase from

your reseller.

CABAC test and measurement equipment complies with Australian EMC regulatory

and international requirements.

CABAC Test Equipment

CABAC Test EquipmentIdeal for professional use in industrial, electrical applications, field environments, laboratory or workshop applications there’s a model to suit every need.

CABAC test equipment use the latest microprocessor technology to provide comprehensive measuring ranges and features in hand held instruments. There is a wide range of test and measurement equipment to suit all applications and budgets.

All products conform to International Standard requirements, and all carry a long list of exclusive features. Some models have “Lifetime of Product Warranty” as standard, and all are backed by the CABAC name for quality.

Whether you are buying a general purpose unit, that has advanced features such as auto ranging, data hold, auto power off, reinforced case for durability, etc. or a professional range unit which offers additional features and accessories, the CABAC range of test equipment will suit your work requirements and provide you with many years of reliable service.

Some models have “Lifetime of Product Warranty”

*Refer to CABAC website cabac.com.au for terms and conditions on warranty.

CABAC OFFERS A CALIBRATION SERVICE FOR INSTRUMENTS The Calibration can either be Factory Standard calibration or independent external NATA accredited calibration. Please note part numbers for calibration of Multimeters, Clamp meters, Installation testers, Multi-function and appliance testers. An installation tester is defined as an instrument that conducts RCD, LOOP or Insulation testing. Multifunction testers which encompass all these testers in the one unit will attract a higher calibration price due to the extra time taken to check all functions.

Part Number DescriptionCALNATAMM NATA Calibration MultimeterCALNATAIMF NATA Calibration Multifunction TestersCALNATACLAMP NATA Calibration ClampCALNATAAPP NATA Calibration Appliance TestersCALNATAINS NATA Calibration Installation Testers

Part Number Description CALSTANMM Factory Calibration MultimeterCALSTANMF Factory Calibration Multifunction TestersCALSTANCLAMP Factory Calibration ClampCALSTANAPP Factory Calibration Appliance TestersCALSTANINS Factory Calibration Insulation Testers

On accepting an instrument to be repaired the following procedure is to take place.

1st R REPAIR1. Provide a quote for labour and parts to repair the instrument to manufacturers specifications. 2. Repair the instrument after receiving written acceptance of the quotation (a purchase order from the

referring wholesale branch is sufficient).3. The work shall be warranted for a maximum of 3 months.

2nd R REPLACEIf the customer elects not to have the instrument repaired then they have the choice to accept as close an equivalent as possible an instrument we supply at a price suggested by the referring wholesaler or pay the minimum quotation fee for the time taken to diagnose the problem. Please note:* The quotation of repair and replacement parts is subject to availability from the supplier especially

in the case of meters not sold by CABAC.* The quotation fee will be waived if the customer purchases one of our suggested replacement

meters.

3rd R RETURNIf the customer elects to pay the quotation fee we will return the instrument to the referring wholesale branch.Please note: *The quotation fee will be charged to the referring wholesaler for unclaimed goods left for more than 3 months.


Part No. C505 •High quality taut band movement •IEC61010 CAT III 600V •Manual scale selection •Easy to read 3-colour scale •Mirror scale for accuracy

PROFESSIONAL ANALOGUE MULTI METER

MULTIMETERS

Unit: EA Qty: 1

Part No. TBM27 •Pocket size - small and compact DMM with EF test and low 2 mA current. •3 5/6 digit 6000 count LCD •Data hold, continuity and diode test •Electric Field (NCV) detection, unit updates 5x per second •HI-Z DCV & ACV

DELUX POCKET DMM Unit: EA Qty: 1

Part No. T8211D •Pen type digital multimeter for testing AC and DC voltage and resistance •IEC61010 CATII 600V •Maximum and data hold •Audible and visual flashing alarm with retractable probe on meter •Suitable for electronic and appliance testing

PEN TYPE METER Unit: EA Qty: 1

Part No. C187 •3 1/2 digit, 4000 count LCD digital multimeter with LAN cable pin to pin testing •Voltage and resistance DMM. CATIII 600V •Data hold, continuity, diode test 7 low battery indication •RJ45/RJ11 pin ot pin testing with/without remote receiver •Ideal instrument for the data cable installer electrician

DMM LAN CABLE TESTER Unit: EA Qty: 1

Part No. T8268 •Autoranging DMM featuring audible and visual lead input socket selection

indication •3 1/2 digit 1999 count LCD •CATIII 600V and backlight LCD •Maximum, relative and data hold •hfe transistor test

AUTO RANGE DIGITAL MULTIMETER Unit: EA Qty: 1


Part No. TBM685 •Rugged and compact voltage, resistance, capacitance and continuity digital

multimeter •IEC 61010CATIV 1000V •Electric Field (NCV) detection strength indication •AutocheckTM Voltage and resistance •Data hold Function

DELUX AUTOCHECK DIGITAL MULTIMETER Unit: EA Qty: 1

Part No. BM251 •Economical, compact multimeter forcontractor’s daily use - functions: data hold,

relative measurement and electric field testing •IEC61010 CATIII 600V & Beep-Jack lead input warning •3 5/6, 6000 count LCD •Electric field test (EF), frequency (Hz) •PC interface with optional BRUA-20X software pack

GENERAL PURPOSE DIGITAL MULTI METER Unit: EA Qty: 1

Part No. TBM805 •Digital multimeter with BEEP-JACK input warning •IEC61010 CATIII 600V •3 ¾ digit 4000 count LCD •Rugged splash-proof housing •Maximum, relative zero and data hold

PRACTICAL PROFESSIONAL DMM Unit: EA Qty: 1

Part No. T8229 •Autoranging DMM, 5 in 1 feature packed with lux, humidity and sound

measurement •CAT III 600V, 3 ¾ 3999 count LCD •Audible & visual socket correct lead input indication •Data hold and relative measurement •Temperature measuremt with type-k thermocouple

5 IN 1 AUTO RANGE DIGITAL MULTIMETER Unit: EA Qty: 1

Part No. BM257 •Compact True RMS DMM, 3 5/6 digit, 6000 count LCD with 24 segment bargraph

and EF bar indication. •CatIV 300V, CATIII 600V, CATIV 300V •Extra feature: min/max, relative zero, crest & data hold •Backlight LCD, Beep-Jack input socket warning •PC interface USB/RS232 (Optional Kit)

MULTIMETER TRUE RMS W/ EF-DETECTION Unit: EA Qty: 1


Part No. TBM807 •True RMS measurement digital multimeter with BEEP-JACK and temperature

range •IEC61010 CATIII 600V •3 ¾ digit 4000 count LCD •Rugged splash-proof housing •Maximum, relative and data hold

TRUE RMS PRACTICAL PROFESSIONAL DMM Unit: EA Qty: 1

Part No. BM821 •Digital multimeter, autoranging with good accuracy and data hold •4 Digit 6000/10000 count dual display LCD •IEC61010 CATIV 1000V •Beep-Jack input warning •Optional PC interface with BU-86X software pack

PROFESSIONAL DIGITAL MULTIMETER Unit: EA Qty: 1

Part No. BM869 •DMM, high performance technicians or engineers. Very accurate and feature

packed multimeter •4 4/5 digit, 50 000 count dual display LCD, backlight •IEC61010 CATIV 1000V, BeepJack input warning •Max/Min/Ave recording, relative zero, crest & data hold •% 4-20 mA loop,dual temperature, optional PC interface

PROFESSIONAL DMM HIGH PERFORMANCE Unit: EA Qty: 1

Part No. BM822 •Digital multimeter, True RMS, autoranging with good accuracy, relativezero & data

hold •4 digit 6000/10000 count, dual display LCD with bargraph •IEC61010 CATIV 1000V •Beep-Jack input warning •Optional PC interface with BU-86X software pack

PROFESSIONAL DMM TRUE RMS Unit: EA Qty: 1

Part No. BM827 •Digital multimeter, True RMS, autoranging feature packed, relative zero, Min/Max,

Crest Hold & Data Hold •4 digit 6000/10000 count, dual display LCD with bargraph •IEC61010 CATIV 1000V •Beep-Jack input warning •Optional PC interface with BU-86X software pack

PROFESSIONAL TRUE RMS DIGITAL MULTIMETER Unit: EA Qty: 1


Part No. BM867 •DMM, high performance technicians or engineers. Very accurate digital and feature

packed •4 4/5 digit, 50 000 count dual display LCD •IEC61010 CATIV 1000V •Max/Min/Ave recording, relative zero, crest & data hold •%4-20 mA loop, BeepJack input warning, optional PC interface

PROFESSIONAL DMM TRUE RMS Unit: EA Qty: 1

Part No. BM319 •3 5/6 digit 6000 count LCD, feature packed automotive DMM •Dwell-angle, % -duty function, IGRPM & IP-RPM •Temperature, capacitance and 600mA ac/dc •Suitable for 2&4 stroke, 2&4 stroke-DIS •CATIII 600V, CATIV 300V• Optional accessory: BM-BP300 Inductive Pick-up Clip

Automotive DMM Unit: EA Qty: 1

Part No. BM525 •True RMS logging digital multimeter, feature packed with high accuracy •IEC61010 CATIV 1000V •4 Digit 6000/10000 count dual display LCD •Max/Min/Avg Recording & data logging memory •Optional PC interface capability with BU-86X software pack

PROFESSIONAL DMM TRUE RMS DATA LOGGER Unit: EA Qty: 1

Part No. BU-86X •USB cable and software for BM821, BM822, BM827, BM525, BM867 and BM869 •Compatible with Windows 7, Vista and XP

USB INTERFACE KIT FOR BM520/820 SERIES Unit: EA Qty: 1

Part No. BM877 •DMM, true RMS for Installation testing with 50V to 1kV Insulation test and

continuity test •EN61010 CATIII 1000V, CAT IV 600V AC and DC •3 5/6 digit, 6000 count dual display LCD, bargraph, backlight •VFD AC Voltage and BeepJack input warning •Polarisation index (PI) and dielectric absortion ratio (DAR)

INSULATION TESTER &DMM CONTINUTY 50V 1KV Unit: EA Qty: 1


Part No. T2600 • Open jaw clamp meter for AC with CATIII 600V multimeter functions and a 3 1/2

digit 3999 count LCD • Easy to use with robust construction • Test lead holder for easy use to testing • Data hold, duty cycle and relative zero functions

DIGITAL CLAMP METER OPEN JAW 200A ACBASC AC CLAMP METERSCLAMP METERS

Unit: EA Qty: 1

Part No. BM111M • Compact clamp suitable for working in small distribution boards • Very light-weight • Large display • Multiple functions including capacitance

DIGITAL CLAMP 600A AC COMPACT Unit: EA Qty: 1

Part No. BM127M • Dual display compact clamp suitable for working in small distribution boards • Very light-weight • Dual readings such as voltage and current • Multiple functions including capacitance and temperature

DUAL SCALE CLAMP ON DIGITAL MULTIMETER Unit: EA Qty: 1

Part No. C2950 • 4000 Count 3 1/2 digit LCD • Data hold • Auto ranging and range/feature select • Auto power OFF

CLAMP METER 1000A ACAC QUALITY CLAMP METERS WITH INCREASED FUCTIONS

Unit: EA Qty: 1

Part No. T9001 • Clamp meter AC current up to 600A and NCV detection • CATIV 600V • 3 3/4 digit 4000 count LCD • Relative and data hold • Voltage test: 10 MOhm input impedance

600A AC CURRENT CLAMP Unit: EA Qty: 1


Part No. BM076 • Compact Clamp 600A ac, true rms, plus EF (NCV), inrush current & phase rotation

testing • CATIII 600V • Min/max/av, data & relative hold • Backlight LCD, 3 5/6 digit, 6000 count LCD • Jaws 30mm cable with AmpTip facility

600A AC TRMS COMPACT CLAMP METER Unit: EA Qty: 1

Part No. TBM116 • True RMS Measurement • 3 3/4 digit 4000 count LCD • Data and relative hold • Large jaw size 45mm • PC interface TBR13X

1000A AC CLAMP TRUE RMS Unit: EA Qty: 1

Part No. BM086 • Clamp 1000A ac, true rms, EF (NCV), plus inrush current and phase rotation

testing • CATIV 600V CATIII 1000V • Min/max/av, data relative hold • Backlight LCD, 3 5/6 digit, 6000 count LCD • Jaws 51mm cable with AmpTip facility

1000A AC TRMS CAT IV COMPACT CLAMP METER Unit: EA Qty: 1

Part No. TBM118 • Clamp meter 2000A AC and DC • 3 3/4 digit 6000 count LCD with backlight • Electric Field (NCV) detection • PC interface kit TBR13X • Large jaw size 45mm

2000A AC CLAMP METER TRUE RMS Unit: EA Qty: 1

Part No. C2010 • 3 1/2 digit 3999 count LCD CATIII 600V true RMS leakage clamp • Measures AC current from mill amperes to 600A • Data hold, continuity, relative and diode check • Auto/manual ranging

LEAKAGE CLAMP METER TO 600ACURRENT CLAMPS WITH SPECIAL FEATURES

Unit: EA Qty: 1


Part No. BM079 • Clamp meter 600A ac/dc, true rms, EF (NCV), plus inrush current and phase

rotation testing • CATIII 600V, 3 5/6 digit, 6000 • MIn/max/ave, data & peak hold • Backlight LCD, feature packed • Jaws 35mm cable with AmpTip facility

600A AC/DC TRMS COMPACT CLAMP METER Unit: EA Qty: 1

Part No. BM089 • Clamp, 1000A ac/dc, true rms, plus EF (NCV) inrush current and phase rotation

testing • CATIV 600V CATIII 1000V • Min/max/Ave, data and peak hold • Backlight LCD, AmpTip, feature packed • Jaws 51mm cable with AmpTip facility

1000A AC/DC TRMS CAT IV CLAMP METER Unit: EA Qty: 1

Part No. TBM135 • True RMS Measurement with 5400 point recording • 3 3/4 digit 6000 count LCD with backlight • Hi-Lo data logging format with optional software for PC interface • Require Sofware interface kit TBR13X for PC connection. • Large jaw size 45mm

1000A AC CLAMP LOGGER TRUE RMS Unit: EA Qty: 1

Part No. T9005 • Clamp 600A ac/dc,True RMS measurement featuring inrush current mode • CATIV 600V • 4 digit 10,000 count LCD • Relative, data, peak hold and min/max recording • Input impedance: 1MOhm.

TRUE RMS CURRENT CLAMP 600A AC/DCAC/DC CURRENT CLAMPS

Unit: EA Qty: 1

Part No. T9105 • CATIV 600V True RMS measurement featuring inrush current mode • Relative, data, peak hold and min/max recording • 4 digit 10,000 count LCD, CATIV 600V • Inrush current for motors. • Low Input Impedance: 1Mohm

TRUE RMS CURRENT CLAMP 1000A AC/DC Unit: EA Qty: 1


Part No. BM197 • 3 5/6 digit, 6000 + 1999 counts dual LCD • Dual display AC+Hz and ACV+Hz • CATIV 1000V • Probe contact EF detection

CLAMP METER 2000A AC/DC Unit: EA Qty: 1

Part No. T202 • Clamp adaptor for digital multimeters with 1mV=1A output • Large jaw 57mm • Two range switch 200A or 2000A DC/1500A AC • Auto zero button and hall effect sensor

DIGITAL CLAMP ADAPTOR - 2000A AC/DCCLAMP ADAPTORS

Unit: EA Qty: 1

Part No. BM157 • 1000A True RMS 3-Phase Power Clamp Meter • CAT III 600V • Includes Test lead pair, users manual & soft pouch

1000A TRUE RMS 3-PHASE POWER CLAMP METER Unit: EA Qty: 1


Part No. T1800 • Featuring low resistance and voltage measurement and supplied with straps to

assist access when testing • Voltage detection live line visual warning light • Handy plastic case with leads compartment • Removable lid

ANALOGUE INSULATION TESTER CATIII 500V

INSULATION METERS

Unit: EA Qty: 1

Part No. T2732 • Low resistance and default voltage measurement • Voltage detection live line visual and audible warning • Robust case protected in rubber boot • Analogue display with ‘parallax error’ mirror

ANALOGUE INSULATION TESTER Unit: EA Qty: 1

Part No. C5201 • 3 1/2 digit 1999 count LCD • Sound and flash alarm • 22mm digital display • Data hold and continuity test

DIGITAL INSULATION TESTER 250/500/1000V Unit: EA Qty: 1

Part No. T2751 • Low resistance and voltage measurement with low Ohms adjustment • Voltage detection live line visual warning light • Selector switch for measuring voltage or insulation resistance • Rugged housing with protective rubber boot

DIGITAL INSULATION TESTER Unit: EA Qty: 1

Part No. C8010 • High Range 200G-Ohm insulation tester with large LCD (78x67), 3 1/2 digits, 2000

count LCD • IEC61010 CAT III 600V. Voltage measurement up 600V • Auto-ranging with 200G-Ohm at 1000V test • Continuity Test at >210 mA • Capacitor test function

DIGITAL INSULATION TESTER Unit: EA Qty: 1


Part No. MD1000R • Insulation tester, up to 200 giga-ohm, 250V, 500V & 1000V, with guard terminal • Low resistance and continuity measurement • Auto ranging and programmable timer • AC/DC voltmeter up to 600V • Rechargeable NiMH battery

INSULATION TESTER 250/500/1000V 200GOHM Unit: EA Qty: 1

Part No. BM877 • DMM, true RMS for Installation testing with 50V to 1kV Insulation test and

continuity test • EN61010 CATIII 1000V, CAT IV 600V AC and DC • 3 5/6 digit, 6000 count dual display LCD, bargraph, backlight • VFD AC Voltage and BeepJack input warning • Polarisation index (PI) and dielectric absortion ratio (DAR)

INSULATION TESTER &DMM CONTINUTY 50V 1KV Unit: EA Qty: 1

Part No. MD5060 • Insulation tester 5kV 5 tera-ohm, auto ranging with digital display and bar graph • Dielectric Absorption Index (DAI), Polarization Index (PI) • Step test voltage and chronometer up to 90 min • Real time clock and calendar • USB interface and built in printer

INSULATION TESTER 5KV-5KV 5TOHM Unit: EA Qty: 1

Part No. TIN7D • High voltage up to 500v to 10kV digital insulation tester with PI and DAR • Suitable for low capacitance equipment such as switch boards • Live Circuit Warning and Auto Discharge • Auto DAR and PI calculation with time duration • Heavy duty case

INSULATION TESTER 1KV TO 10KV Unit: EA Qty: 1

Part No. MD10kVR • 10kV insulation tester up to 10Tera Ohms with chronometer, AC/DC voltmeter and

printer • Automated PI and DAR. Anndroid device connection • Built memory for logging • Real time clock and calendar • Rechargable LiFePO4 battery

INSULATION TESTER DIGITAL 10KV 10TOHM Unit: EA Qty: 1


Part No. T2726 • Loop impedance analyser with LED mains polarity supply indication and PSC • Simple one test button action when LED correct • Single phase electrical network tester • Test output about 15A pulses. Requires RCD wiring bypass • Tests loops active/neutral, active/earth, neutral/earth

LOOP IMPEDENCE AND PSC Unit: EA Qty: 1

Part No. T2712EL • Residual Current Device (RCD) or ELCB trip time tester with LED indication for

power, battery and mains polarity • Simply select earth leakage resistance test value • Displays adjustment percentage for high and low voltage • Suitable for 10A and 30 mA RCDs • CAT III 300V

DIGITAL RCD TESTER - 240V Unit: EA Qty: 1

Part No. TEL11 • Three phase trip time and trip current RCD (ELCB) tester with robust, impact

resistant housing and removable lid • Tests single and three phase RCDs • Operating voltage 100V to 500V • Selection of phase angle 0 or 180 degrees

THREE PHASE RCD TESTER Unit: EA Qty: 1

Part No. T2720 • Earth resistance tester for two or three electrodes • 3 1/2 digit 1999 count LCD • Measures earth voltage to 200V • Includes electrodes, long leads and simple push button operation • Spare lead set: AL36RYGKIT

DIGITAL 3 WIRE EARTH TESTER Unit: EA Qty: 1

Part No. C4235 • Multifunction LCM display • CATIV 300V • Tests earth resistivity and earth resistance • 2, 3 and 4 wire testing

EARTH RESISTANCE TESTER Unit: EA Qty: 1


Part No. INSTALTESTKIT • Complete, compact installation kit with ability to test according to AS/NZS 3000 • IEC61010 CATIII 600V, CATIV 300V • Multifunction 128 x 64 dot matrix LCD

MI3125 INSTALLATION TEST KIT AS/NZ3000 Unit: EA Qty: 1

Part No. INSTALTESTKITB • Complete, compact installation kit with ability to test according to AS/NZS 3000 • Includes sofware option for logging and records • Multifunction 128 x 64 dot matrix LCD • IEC61010 CATIII 600V, CATIV 300V • Kit includes MI3125 and accessories

MI-3125B INSTEST KIT INCL. SOFTWARE Unit: Qty:


Part No. WIBRETEST • CATIV 300V voltage tester, solenoid type 125V up to 750V AC and 110V to 750V

DC • Rubber handles and tough probe housing • Suitable for 240V single phase and 415V three phase voltage tests • Light indication for ‘live’ and AC or DC • Solenoid indicator drains low energy signals

VIBRATING VOLTAGE AND LINE TESTER CATIVVOLTAGE TESTERS

Unit: EA Qty: 1

Part No. BT-71EU • Voltage tester AC & DC with LED voltage and polarity indication plus EF (NCV)

Tester • Made to EN61010 CATIV 600V & EN61243-3 • Optional plugable test lead available up to 3m long • Test probes 4 & 2 mm diameter for various applications • Audible continuity test

1000V LED VOLTAGE TESTER Unit: EA Qty: 1

Part No. C3031 • LED and LCD displays • CATIV 600V • Voltage to 690V AC/DC

DIGITAL VOLTAGE TESTER CATIV 600V Unit: EA Qty: 1

Part No. BT-73EU • Voltage tester AC & DC with LED/LCD voltage, polarity & phase rotation indication

plus EF Tester & RCD trip test • Made to EN61010 CATIV 600V & EN61243-3 • Optional plugable test lead available up to 3m long • Test probes 4 & 2 mm diameter for various applications • True RMS measurement & Audible continuity test

1000V LCD + LED VOLTAGE TESTER Unit: EA Qty: 1

Part No. T2600 • Open jaw clamp meter for AC with CATIII 600V multimeter functions and a 3 1/2

digit 3999 count LCD • Easy to use with robust construction • Test lead holder for easy use to testing • Data hold, duty cycle and relative zero functions

DIGITAL CLAMP METER OPEN JAW 200A AC Unit: EA Qty: 1


Part No. BM039F • 200ac 12mm slip open jaw clamp DMM, True RMS, with backlight and EF (NCV)

detection • 3 5/6 digit 6000 count LCD, Crest/Data Hold • 600V, 6MOhm, 2.5mF, 999.9Hz with LPF • EF Bargraph, Temperature, DC micro Amps • CAT III 600V, CAT IV 300V

OPEN JAW 200A AC CLAMP METER Unit: EA Qty: 1

Part No. ACTEST3 • Neon light indicator lamp style test screwdriver • GS/TUV and CE approvals • Featuring an insulated shaft • 3.5mm driver tip width and 190 mm long • Weight: 27g

AC TEST SCREWDRIVER 3.5 X 190MMVOLTFINGER (TEST PENS)

Unit: EA Qty: 1

Part No. T7107A • CATIV 1000V non-contact voltage detector with optional belt pouch available,

suitable for tracing live” wires and conductors” • Voltage range 50-1000V • Variable tone buzzer to indicate voltage intensity • Audible and bright LED voltage indication • Spare pouch & clip - VPOUCH & T7107A-CLIP

VOLTAGE DETECTOR CATIV 1000V Unit: EA Qty: 1

Part No. C8902A • CATIII 600V voltage proximity sensor with adjustable sensitivity for polarity testing • Visual and audible indication • On/Off button • Double moulded

AC VOLTAGE (NCV) DETECTOR ADJ CATIII 600 Unit: EA Qty: 1

Part No. C3121 • LED visual and audible Non-Contact Voltage (NCFor EF) indication • LED torch next to test point • ON/OFF switch and sensitivity buttons • Ideal for tracing and locating live” conductors” • CATIV 1000V

VOLTFINGER WITH TORCH NON CONTACT Unit: EA Qty: 1


Part No. C6818 • LCD displays digital readout and bargraphs and includes a NCV Detector • CATIII 300V for both receiver and transmitter • Suitable for any conductor tracing • Three strength level options in transmitter

CIRCUIT CABLE TRACERCABLE TRACER

Unit: EA Qty: 1

Part No. T606 • Digital phase rotation tester with ‘live’ line and two way rotation indication • Plug in standard instrument test leads • IEC61010 CATIII 500V • No moving mechanical parts, compact and light

PHASE ROTATION TESTERPHASE SEQUENCE (ROTATIO) TESTER

Unit: EA Qty: 1

Part No. T860 • Phase and motor rotation tester • CATIII 500V • Separate circuits for testing phase and motor rotation • Bright neon light indication and plug in leads

PHASE AND MOTOR ROTATION MTR CATIII 500V Unit: EA Qty: 1

Part No. C895 • Phase sequence indicator with non-contact probes CATIV 600V and CATIII 1000V • Indicates phase voltage (75V to 1000V AC) • Bright LED for outdoor indication • Test lead length 1.5m for overhead lines • Use for phase voltage 70V to 1000V

PHASE ROTATION TESTER NON-CONTACT CATIV Unit: EA Qty: 1

Part No. TEL1TLV2 • Socket polarity visual tester indication • Suitable for 230V 10A Australian socket outlets • RCD trip tester with push button • RCD trip tester with push button • Indicates Active polarity compared to neutral/earth

POWER POINT TESTER V2SOCKET TESTERS

Unit: EA Qty: 1


Part No. R158003 • Voice, Data and Video Cable Verifier for testing data cabling, telephone wiring and

video/security cabling • All the features of the VDV II Plus model # R158002 plus: • PoE detection with voltage information • Media Service detection such as ISDN, PBX and PoE • Comes in a carry case with multiple test adaptors and leads

VDV II PRO CABLE VERIFIERIDEAL LAN TESTERS

Unit: EA Qty: 1

Part No. 35RJTST8 • Primary use is for testing continuity, shorts and open circuits, individual cables and

pairs of UTP or STP • Remote display unit allows for viewing at either end • Displays pairs and crossed pairs • Includes LEDs for each wire ensuring easy pin configuration

LAN TESTER 10BASET 10BASE2 BNC/RJLAN TESTERS

Unit: EA Qty: 1

Part No. 256655 • An ideal tool for network installers and trouble shooters working on small LANs • Ideal for testing switches and NIC cards • Auto-negotiation function tests the LAN devices speed up to 100MB • Port-finder function sends signal to switch to identify the port

NETWORK DIAGNOSTIC TOOL Unit: EA Qty: 1

Part No. WL-F601 • Provides specific information about each network when there are multiple

networks • Provides channel information (1 to 13) • Shows signal availability 802.11b and 802.11g • Detects encryption (WEP and WPA) range 60m

DIGITAL HOTSPOTTERWIFI TESTERS

Unit: EA Qty: 1


Features

ACTEST3 T7107A C8902A C3121

Screwdriver Touch Tester NCV Adjustable NCV NCV/ Torch

Audible NCV √ √ √

Visual NCV √ √ √ √

Vibration Detect

AC/DC AC AC AC AC

NCV Detect √ √ √

Magnetic Field Indication

Torch Light LED

Special FeaturesDetects

Energised Solenoids

CATIII 300V 1000V 600V 1000V

CATIV - 1000V 300V 1000V

Warranty 1 1 1 1

SC

RE

WD

RIV

ER

VO

LT F

ING

ER

S -

EF

OR

NO

N C

ON

TAC

T V

OLT

AG

E D

ETE

CTO

RS

(NC

V)

Voltage Detectors and Testers

Features

WIBRETEST BT-71EU BT-73EU C3031

Voltage Tester LED Voltage Continuity. RCD trip

LED/LCD Voltage Continuity. RCD trip

LED/LCD/ Voltage/ Continuity/ Phase

Rot.

Audible NCV √ √ √

Visual NCV √ √ √ √

Vibration Detect √

AC/DC AC/DC AC/DC AC/DC AC/DC

NCV Detect √ √

Magnetic Field Indication

Torch Light √ LED

LCD Backlight √

Continuity √ √ √

LED Scale √ √ √

LCD √ √

Phase Rotation √ √

Special Features Single PoleSelf Test, Single Pole,

EF, Optional Long Lead

Self Test, Single Pole, EF, RCD Trip, True

RMS, Optional Long Lead

Single Pole

CATIII 600V 1000V 1000V 1000V

CATIV 300V 600V 600V 600V

Warranty 1 1 1 1

VO

LTA

GE

TE

STE

RS

Voltage Detectors and Testers - Selection Chart

Voltage Testers - Selection Chart


Mul

timet

ers

- Sel

ectio

n C

hart

Multem

eters

FEAT

UR

ESC

505

T821

1DT8

221C

TBM

22TB

M27

C18

7T8

268

T822

9TB

M68

5B

M25

1B

M25

7TB

M80

5TB

M80

7B

M31

9B

M82

1B

M82

2B

M82

7B

M87

7B

M52

5B

M86

7B

M86

9

Dis

play

Ana

log

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

Dig

ital

LCD

cou

nts

1999

1 99

94

000

6 00

040

003

999

3 99

96

000

6 00

060

004

000

4 00

060

0010

000

1000

010

000

6000

1000

050

000

50 0

00

LCD

dig

its3

½3

½3

¾3

5 ⁄63

1 ⁄23

3 ⁄43

3 ⁄43

5 ⁄65

5 ⁄65

5/6

3 3 ⁄4

3 3 ⁄4

3 5 ⁄6

3 5 ⁄6

3 5 ⁄6

3 5 ⁄6

3 5 ⁄6

3 5 ⁄6

4 4 ⁄5

4 4 ⁄5

Bar

grap

h√

√√

√√

√√

√√

√√

Bat

tery

Tes

t√

√√

√√

√√

√√

√√

√√

√√

√√

√√

Max

AC

Vol

tage

1000

600

600

600

600

7075

075

010

0010

0010

0010

0010

0010

0010

0010

0010

0010

0010

0010

0010

00

Max

DC

Vol

tage

1000

600

600

600

600

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

1000

Max

AC

Cur

rent

(A)

1010

2 m

A10

1010

1010

1010

1010

1010

1010

10

Max

DC

Cur

rent

(A)

1010

2 m

A10

1010

1010

1010

1010

1010

1010

10

Fuse

d R

ange

200m

A10

10√

√√

√√

√√

√√

√√

√

Max

Res

ista

nce

20M

20M

20M

40M

6M40

M20

0M40

M6M

60M

60M

40M

40M

60M

60M

60M

60M

60M

(25G

)60

M50

M50

M

Con

tinui

ty B

eepe

r√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√

Dio

de T

est

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√

Aut

oran

ging

√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√

Freq

uenc

y (H

z)20

k10

0k10

0K1-

50k

1M1k

1k1k

1k10

- 100

k1k

200k

200k

Cap

acita

nce

µF20

020

0020

0020

020

020

0030

0030

0030

0020

0025

m25

m25

m30

m25

m25

m25

m

Tem

pera

ture

°C-2

0 to

100

0-2

0 to

100

0-5

0 to

100

0-5

0 to

100

0-5

0 to

998

-50

to 9

99-5

0 to

100

0

Min

/Max

Hol

dm

axm

ax√

√m

axm

ax√

√√

√√

Dat

a H

old

√√

√√

√√

√√

√√

√√

√√

√√

√√

Cre

st o

r Pea

k H

old

√√

√√

True

RM

S M

easu

rem

ent

√√

√√

√√

√√

Bac

k Li

ght

√√

√√

√√

√√

√√

√√

√

Spla

sh &

Dus

t Pro

of√

√√

√√

√√

√√

√√

√√

√√

Tran

sien

t Pro

of6k

V6k

V6k

V4k

V4k

V6k

V6k

V12

kV6k

V6.

5kV

6kV

6kV

6kV

12kV

12kV

12kV

8kV

12kV

12kV

12kV

Rel

ativ

e R

efer

ence

√√

√√

√√

√√

√√

√√

Hol

ster

√√

√√

√√

√√

√√

√√

√√

Aut

o Po

wer

Off

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

Fire

Ret

ard

Cas

e√

√√

√√

√√

√√

√√

√√

√√

PC C

omm

s.U

SB

US

BU

SB

US

BU

SB

US

BU

SB

US

B

Dat

a lo

gger

√

Oth

er F

eatu

res

Taut

Ban

d m

ovem

ent.

Mirr

or

Com

pact

pe

n ty

pehf

e 1-

1001

LAN

C

able

Te

ster

.R

J45,

R

J11

Inco

rrec

t S

ocke

t Ale

rt

Dua

l D

ispl

ay,

RH

%,

Lux,

dB

, In

corr

ect

Soc

ket

Ale

rt

EF

EF

Logi

c Le

vel

Hz,

E

F

Dw

ell

Ang

le,

RP

M,

ms-

Fuel

In

ject

ion

dete

ctor

, S

elec

tabl

e

Dua

l D

ispl

ay,

Bee

pJac

k

Dua

l D

ispl

ay,

Bee

pJac

k

Dua

l D

ispl

ay,

Bee

pJac

k,

EF,

Log

ic

Leve

l Hz,

E

F

Dua

l D

ispl

ay,

Bee

pJac

k,

Insu

latio

n Te

st,

PI

& D

AR

, C

ontin

uity

Te

st,

Dua

l D

ispl

ay,

Bee

pJac

k,

Logg

ing

Mem

ory,

D

ual T

1-T2

Dua

l D

ispl

ay,

%4-

20m

A,

dBm

, B

eepJ

ack

Dua

l D

ispl

ay,

%4-

20m

A,

dBm

, VFD

, B

eepJ

ack,

D

ual T

1-T2

CAT

III

600

600V

600V

300V

300V

600V

600V

600

V10

00V

600V

600V

600V

600V

CAT

III

600V

>100

0V>1

000V

>100

0V10

00V

>100

0V>1

000V

>100

0V

CAT

IV30

0V30

0V15

0V15

0V30

0V30

0V30

0V10

00V

300V

300V

300V

300V

CAT

IV

300V

1000

V10

00V

1000

V60

0V10

00V

1000

V10

00V

War

rant

y (y

ears

)1

11

11

11

1L.

O.P

.L.

O.P

.L.

O.P

.1

11

L.O

.P.

L.O

.P.

L.O

.P.

L.O

.P.

L.O

.P.

L.O

.P.

L.O

.P.


Clamp Meters - Selection ChartClamp meters

FEATURES T2600 BM039F BM111M BM127M C2010 C2950 T9001 BM076 TBM116 TBM135 BM086

Jaw Size 12 12.5 26 28 31x40 35 42 30 45 45 51

Display Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital

LCD Display Counts 3999 6000 4000 4000 4000 4000 4000 6000 4000 4000 6000

LCD Display Digits 3 ¾ 3 ⅚ 3 ¾ 3 ¾ 3½ 3 ¾ 3 ¾ 3 ⅚ 3 ¾ 3 ¾ 3 ⅚

Backlight √ √ √ √ √ √ √ √

Bargraph √

AC Current 200 200 600 400 600 1000 600 600 1000 1000 1000

DC Current

AC Voltage 700 600 600 600 600 600 600 600 600 600 1000

DC Voltage 1000 600 600 600 600 1000 600 600 600 600 1000

Auto Ranging √ √ √ √ √ √ √ √ √ √ √

Relative Zero √ √ √ √ √

APO √ √ √ √ √ √ √ √ √ √ √

Resistance (Ω) 40M 6M 40M 40M 20M 40M 40M 60k 40M 1k 60k

Continuity Buzzer √ √ √ √ √ √ √ √ √ √

Frequency (Hz) 100k 1K 50k 50k 100k 5M 5-400k 500 5-400k

Capacitance (µF) 4 2500 3000 4000 200µ 100 2500 2500

Temperature °C -40 to 400 -20 to 300 20 to 1000 -40 to 400 -50 to 300 -40 to 400

True RMS √ √ √ √ √

Diode Test √ √ √ √ √ √ √ √

Peak Hold √

Data Hold √ √ √ √ √ √ √ √ √ √

Min/Max Recording √ Max Max √ √ √

Special Features LPF for VFD V-fundamentals Dual Display Leakage, Low

Pass Filter

Flashlight. 10A Splitter with x1

& x10EF (NCV)

EF (NCV), Inrush I,

AmpTip, Phase Rotation, DC

µA

Comms

Current Logger, HDT%-R, Serial PC Comms

EF (NCV), Inrush I,

AmpTip, Phase Rotation, DC

µA

CAT II 600V

CAT III 600V 600V 600V 600V 600 - 1000V 600 600V 600V 1000

CAT IV 300V 300V 300V 300V 300 - 600V 300 300V 300V 600

Warranty Years 1 1 1 1 1 1 1 1 1 1 1

FEATURES TBM118 C2108 T9005 BM079 T9105 BM089 BM197 BM157 T202 TA3000

Jaw Size 45 26 42 35 34x65 51 55 45 57 194

Display Digital Digital Digital Digital Digital Digital Digital Digital Adaptor Adaptor

LCD Display Counts 6000 6600 10000 6000 10000 6000 6000 +1999 6000/9999

LCD Display Digits 3 ⅚ 3 ⅚ 4 3 ⅚ 4 3 ⅚ 3 ⅚ 3 ⅚

Backlight √ √ √ √ √ √ √

Bargraph √ √

AC Current 2000 660 600 600 1000 1000 2000 1000 1500 3000

DC Current 660 400 600 600 1000 2000 2000

AC Voltage 600 660 600 600 600 1000 1000 600

DC Voltage 600 660 600 600 600 1000 1000 600

Auto Ranging √ √ √ √ √ √ √ √

Reletive Zero √ √ √ √ √ √

APO √ √ √ √ √ √ √

Resistance (Ω) 6M 6M 40M 60k 40M 60k 40M

Continuity Buzzer √ √ √ √ √ √ √ √

Frequency (Hz) 50k 10k 400 5-400k 400 5-400k 400Hz

Capacitance (µF) 2000 66m 999.9 2500 999.9 2500 2000

Temperature °C -40 to 1200 -40 to 400 -40 to 1200 -40 to 400 -50 to 1000-50 to 300

True RMS √ √ √ √ √ √ √ √

Diode Test √ √ √ √ √ √ √ √

Peak Hold √ √ √ √

Data Hold √ √ √ √ √ √ √ √

Min/Max Recording √ √ √ √ max

Special Features Comms, EF (NCV) Clamp Light 1MΩ Imput

Impedance

EF (NCV), Inrush I, AmpTip, Phase Rotation, DC µA

EF (NCV), Inrush I, AmpTip, Phase Rotation, DC µA

Autocheck, VFD-V, VFD-A, Inrush, EF, PC

Interface

kVA, W, THD%, Serial PC

Comms, Cosϕ

CAT II

CAT III 600V 600V 1000V 600 1000V 1000 1000 600 600 600

CAT IV 300V 300V 600V 300 600V 600 1000 300 300 300

Warranty Years 1 1 1 1 1 1 1 1 1 1


Insu

latio

n Te

ster

s - C

ompa

rison

Cha

rtIn

sula

tion

test

ers

FEAT

UR

ES

INSULATION TESTERS

T180

0T2

732

T275

1B

M87

7C

8010

C52

01M

D10

00R

TIN

6AM

D50

60TI

N7D

MD

10K

VR

INSTALLATION TESTERS

INST

ALT

ESTK

ITIN

STA

LTES

TKIT

BD

ispl

ayA

nalo

gue

Ana

logu

eD

igita

lD

MM

Dig

ital

Dig

ital

Dig

ital

Ana

logu

eD

igita

lD

igita

lD

igita

lD

igita

lD

igita

l

50 V

Tes

t Vol

tage

√√

√

100

V T

est V

olta

ge√

√√

√

250

V T

est V

olta

ge√

√√

√√

√√

√√

500

V T

est V

olta

ge√

√√

√√

√√

√√

√√

√

1000

V T

est V

olta

ge√

√√

√√

√√

√√

√√

√

2500

V T

est v

olta

ge√

√√

5000

V T

est V

olta

ge√

√√

√

1000

0 V

Tes

t Vol

tage

√√

√

Hig

h R

esis

tanc

e R

ange

0-

400

MΩ

500

k

-400

MΩ

20, 2

00 &

20

00 M

Ω0.

02 to

25

GΩ

0 to

200

GΩ

10

00V

2GΩ

at

1000

V1

to 2

00

GW

100

0V<4

00G

Ω &

<

400

GΩ

5 TΩ

800k

Ω

- 500

GΩ

10 T

Ω<

19 M

Ω, 2

0- 9

9MΩ

&

100-

199M

Ω<

19 M

Ω, 2

0- 9

9MΩ

&

100-

199M

Ω

Insu

latio

n Te

st C

urre

nt2

mA

1.3

mA

1 m

A1m

A1m

A1m

A1.

5 m

A1.

5 m

A1.

5mA

Varia

ble

2mA

1 m

A1

mA

Con

tinui

ty T

est C

urre

nt24

0 m

A20

5 m

A21

0mA

110m

A-2

0Ω

210m

A-2

Ω>2

10m

A20

0mA

>200

mA

--

--

200m

A20

0mA

Low

Res

ista

nce

0-50

&

Infin

ity0-

3, &

500

0-20

/

0-2

00/

0-20

000.

015

to

21.9

9Ω0

to 2

0MΩ

0 to

200

Ω-

--

-0

- 199

9Ω0

- 199

9Ω

Tim

er (C

ontin

uous

Tes

t)√

√√

√√

√√

√

Live

Circ

uit W

arni

ng√

√√

√√

√√

Aut

omat

ed O

pera

tion

√√

√√

√√

√√

Aut

o D

isch

arge

√√

√√

√√

√√

√√

√√

Res

ista

nce

Buz

zer

√√

√√

Volta

ge M

easu

rem

ent

0-60

0 VA

CD

efau

lt

0-60

0 VA

C

Def

ault

0-

600

VAC

1000

V A

C/

DC

, VFD

-V

600V

600V

AC

/DC

700V

AC

, 10

00V

DC

600V

A

C/D

C-

--

1000

V55

0V A

C55

0V A

C

Bat

tery

Che

ck√

√√

√√

AC

/DC

√√

AP

O√

√√

√√

√√

√√

√√

Mem

ory/

Dat

a S

tora

ge√

√√

√

PC

Com

ms

√√

US

B

Spe

cial

Fun

ctio

ns

0-3Ω

R

ange

, D

efau

lt Vo

ltage

Te

st

Dua

l Rea

ding

D

ispl

ay,

VFD

-F,

VFD

-Hz,

PI,

DA

R, T

rue

RM

S.

1000

V

Insu

latio

n Te

st

Up

to 2

00G

Ω

Gua

rd

Term

inal

, re

char

gebl

e ba

tterie

s,

DA

R, P

I, P

ass/

Fail,

Tr

ue R

MS

1 W

Out

put

DA

R &

PI,

Mem

ory,

PC

tra

nfer

US

B,

Prin

ter,

Gua

rd,

rech

arge

able

Li

FeP

O4

Bat

terie

s

1W o

utpu

t, D

AR

, PI,

Tim

er,

Ene

rsav

eTM

DA

R &

PI,

Mem

ory,

P

C tr

anfe

r U

SB

, Prin

ter,

Gua

rd,

rech

arge

able

Li

FeP

O4

Bat

terie

s,

IP54

, GP

S

Loop

Impe

danc

e,

PS

C,

RC

D, S

ocke

t, B

ackl

ight

, P

olar

ity,

Pha

se R

otat

ion

Loop

Impe

danc

e, P

SC

, R

CD

, Soc

ket,

back

light

, P

olar

ity, P

hase

Rot

atio

n,

Sof

war

e &

PC

link

.

IEC

6101

0 R

atin

g (C

AT II

I)60

0V60

0V60

0V10

0060

060

060

0V60

0V30

0V60

060

0V60

0V

IEC

6101

0 R

atin

g (C

AT IV

)30

0V30

0V30

0V60

030

030

060

0V30

0V15

0V30

0V30

0V

War

rant

y (y

ears

)1

22

L.O

.P.

11

11

11

11

1

Not

e A

S/N

ZS61

010

Rat

ing

is re

quire

d fo

r vol

tage

mea

sure

men

t, no

t ins

ulat

ion

test

ing.


LEADS - VERSION 2

Part No. AL01 AL02 AL04 AL24 AL28-1 AL28-3 AL28-5 AL30RBGKIT AL30RWBKIT

Description 1kV 10A Black Single Lead

1kV 10A Black Single Set +

Croc-Clip

1kV 10A DMM Set

PVC, Set Threaded Pins

1kV 10A DMM Set

1kV 10A 4mm Probe

1kV 10A Threaded set +

Croc Clips

Set L, N & E with Croc-Clips

Set L1, L2 7 L3 with Croc-Clips

Lead Length (m) 3 0.9 0.84 1

Probe Φ (mm) 2 2 Threaded 2 4 2 Threaded 4

Instrument Plug 90o 4mm shrouded

Colours Black Red & Black

Set of: 1 2

Accessories - Small Croc-Clips - Small

Croc-Clips Large Croc-Clips

CAT III 1000V

CAT IV 1000V

Part No. AL04RBY TEL-EL TEL-AN AL35L AL37B AL37R AL38C AL52F AL57F10A AL36RYGKIT AL-4WER

DescriptionTest Lead Set RD/BK/YL with

Croc-Lips

RCD test 10A Plug and Lead

RCD test 10A Plug and Lead

No Neutral

Silicone Insulated Lead Set

Stacking Lead Black

Stacking Lead Red

Croc-Clips for 4mm Banana Probes

Fused Leads Set 2A CAT IV

Fused Lead Set 10A CAT IV

Test Lead Set for Earth Resistance

Tosters

Earth Resistance

Leads for 4-Wire

Testers

Lead Length (m) 1 0.5 1 0.5 N/A 1

Green - 5m Yellow - 10mRed - 15m

Red - 36m Spike 45cmBlack- 3m Blue - 20m

Green - 50mProbe

Φ (mm) 2 10A Plug 10A Plug Croc-Clips

Instrument Plug

90o 4mm shrouded Shrouded 4mm Straight 90o 4mm

shrouded

Straight 4mm

shrouded piggy back

Straight 4mm

shrouded piggy back

90o 4mm shrouded

Colours Red, Black, Yellow

Red, Green & Black

Red & Green Red & Black Black Red Red & Black Red, Green,

Yellow

Black, Blue, Green,

Red + Spikes

Set of: 3 1 2 1 2 3 4

Accessories 2x Croc Clips 10A Plug Optional - Croc-Clips Optional Croc-Clips -

CAT III 1000V 600V 1000V 600V 690V 2A 1000V 10A 600 2A -

CAT IV 1000V - 600V 300V 690V 2A 600V 10A - -

Leads - Comparison Chart


Notes:

In support of our policy of continuous product improvement we reserve the right to change materials and specifications without notice. Drawings, where shown, may not be to scale. Dimensions are metric and size maybe approximate. Where possible data sheets including MSDS are made available on our website and APPs. All products should be installed and used in accordance to manufacturer’s instruction provided. Warning: products may be subject of registered designs and patents. Refer to our website or APPs for terms and conditions on warranty. Every effort has been made to ensure accuracy of content. However no liability will be met by CABAC or its suppliers for any errors or omissions. Product data and information is no binding. All brands and logos are registered trademarks and are subject to copyright laws. No part of this catalogue can be reproduced without the consent of CABAC. The ‘One Call, One Day, One Delivery’ does not cover the following items: Cast Resin Kits, Custom Manufacturing & Kitting, Cabinets, Ladders, Pits & Pillars, CABTRAY, TRIPAC and Branch Stock Orders.

CABAC

133 122 | CABAC.COM.AU

TEST MEASUREMENT...Test Equipment CABAC Test Equipment Ideal for professional use in industrial, electrical applications, field environments, laboratory or workshop applications there’s

Documents