Acreditation nº 41/LE104. Evaluation Nº 23887 Technical Annex Updated Page 1 of 18 TECHNICAL ANNEX ACREDITATION Nº 41/LE104 Entity: ASSOCIATION FOR THE PROMOTION OF RESEARCH AND FIRE SAFETY TECHNOLOGY (AFITI) Address: (1) Camino del Estrechillo, nº 8; 28500 Arganda del Rey (Madrid) (2) C/ Río Estenilla s/n – Pol. Ind. Sta. Mª de Benquerencia; 45007 Toledo (3) Ctra. CM-320 km. 3,500; 16400 Tarancón (Cuenca) Reference Standard: UNE-EN ISO/IEC 17025: 2005 (CGA-ENAC-LEC) Tests in the following area: Fire Protection Category 0 (Tests in the permanent laboratory) PRODUCT/MATERIAL TO BE TESTED TEST TEST STANDARD/PROCEDURE PART A: REACTION TO FIRE (2) Building materials (excepting coating, finishes and laminated products) Conditioning procedures and general rules for selection of substrates UNE-EN 13238:2011 Non-combustibility Test Classification (See Note 1) UNE 23102:1990 UNE-EN ISO 1182:2011 UNE-EN 13501-1:2007+A1:2010 UNE 23727:1990 Rigid and flexible building materials thicker than 5 mm (excluding stretched coverings of walls or ceilings and flexible filtration materials) Radiation Test Classification UNE 23721:1990 UNE 23727:1990 Flexible building materials 5 mm thick or less Electrical burner Test Classification UNE 23723:1990 UNE 23727:1990 Building materials not intended to be placed on a rigid substrate Speed of the spread of flame Test Classification UNE 23724:1990 UNE 23727:1990
18
Embed
TECHNICAL ANNEX ACREDITATION Nº 41/LE104 …static.plenummedia.com/...41le_104_en_actualiz2015.pdf · TECHNICAL ANNEX ACREDITATION Nº 41/LE104 Entity: ASSOCIATION FOR THE PROMOTION
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Acreditation nº 41/LE104. Evaluation Nº 23887
Technical Annex Updated Page 1 of 18
TECHNICAL ANNEX ACREDITATION Nº 41/LE104
Entity: ASSOCIATION FOR THE PROMOTION OF RESEARCH AND FIRE SAFETY TECHNOLOGY (AFITI)
Address: (1) Camino del Estrechillo, nº 8; 28500 Arganda del Rey (Madrid) (2) C/ Río Estenilla s/n – Pol. Ind. Sta. Mª de Benquerencia; 45007 Toledo (3) Ctra. CM-320 km. 3,500; 16400 Tarancón (Cuenca)
Fire resistance tests for fire barriers CEN-TS 45545-3 :2009
Structural elements
Fire resistance tests for load-bearing elements: Walls Classification (See Note 1)
UNE-EN 1365-1:2000 UNE-EN 13501-2:2009+A1:2010
Fire resistance tests for load-bearing elements: Floors and Roofs Classification (See Note 1)
UNE-EN 1365-2:2000 UNE-EN 13501-2:2009+A1:2010
Fire resistance tests for beams Classification (See Note 1)
UNE-EN 1365-3:2000 UNE-EN 13501-2:2009+A1:2010
Fire resistance tests for columns Classification (See Note 1)
UNE-EN 1365-4:2000 UNE-EN 13501-2:2009+A1:2010
Stripes of encounter of dividing wall and roof
Technical Application Guide: Fire Safety Regulation in Industrial Establishments. Annex B. Edition of October 2007
Determining the contribution to the fire resistance of horizontal protective membranes Classification (See Note 1)
CEN-TS 13381-1:2005 UNE-EN 13501-2:2009+A1:2010
Determining the contribution to the fire resistance of vertical protective membranes Classification (See Note 1)
UNE-ENV 13381-2:2004 UNE-EN 13501-2:2009+A1:2010
Determining the contribution to the fire resistance of applied protection to concrete structural members Classification (See Note 1)
UNE-ENV 13381-3:2004 UNE-EN 13501-2:2009+A1:2010
Determining the contribution to the fire resistance of applied protection to steel structural members Classification (See Note 1)
UNE-ENV 13381-4:2005 UNE-EN 13501-2:2009+A1:2010
Acreditation nº 41/LE104 Technical Annex Updated
Page 6 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Structural elements (continued)
Determining the contribution to the fire resistance of applied protection to concrete/profiled sheet steel composite members Classification (See Note 1)
UNE-ENV 13381-5:2005 UNE-EN 13501-2:2009+A1:2010
Determining the contribution to the fire resistance of structural members: Applied protection to concrete filled hollow steel columns. Classification (See Note 1)
UNE-ENV 13381-6:2004 UNE-EN 13501-2:2009+A1:2010
Determining the contribution to the fire resistance of structural members: Applied protection to timber members. Classification (See Note 1)
UNE-ENV 13381-7:2006 EX UNE-EN 13501-2:2009+A1:2010
Determining the contribution to the fire resistance of structural members: Applied reactive protection to steel members. Classification (See Note 1)
UNE-EN 13381-8:2011 UNE-EN 13501-2:2009+A1:2010
Service installations Fire resistance tests for ducts
Classification (See Note 1)
UNE-EN 1366-1:2000 UNE-EN 13501-3:2007+A1:2010
Fire resistance tests for fire dampers Classification (See Note 1)
UNE-EN 1366-2:2000 UNE-EN 13501-3:2007+A1:2010
Cycling test for fire dampers (performed in Arganda del Rey only)
UNE-EN 15650:2010 Annex C
Fire resistance tests for penetration seals Classification (See Note 1)
UNE-EN 1366-3:2011 UNE-EN 13501-2:2009+A1:2010
Fire resistance tests for linear joint seals Classification (See Note 1)
UNE-EN 1366-4:2008+A1:2010 Except Annex B UNE-EN 13501-2:2009+A1:2010
Fire resistance tests for technical floors Classification (See Note 1)
UNE-EN 1366-6:2005 UNE-EN 13501-2:2009+A1:2010
Fire resistance tests for smoke extraction ducts Classification (See Note 1)
UNE-EN 1366-8:2005 UNE-EN 13501-4:2007+A1:2010
Acreditation nº 41/LE104 Technical Annex Updated
Page 7 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Service installations (continued)
Fire resistance tests for single compartment smoke extraction ducts Classification (See Note 1)
UNE-EN 1366-9:2009 UNE-EN 13501-4:2007+A1:2010
Specification for powered smoke and heat exhaust ventilators Classification (See Note 1)
UNE-EN 12101-3:2002 Annex C UNE-EN 12101-3:2002/AC:2006 UNE-EN 13501-4:2007+A1:2010
Specification for natural smoke and heat exhaust ventilators Classification (See Note 1)
UNE-EN 12101-2:2004 Annexes C, D, G and Annex F except para.F.4.2. UNE-EN 13501-4:2007+A1:2010
Circuit integrity maintenance of electric cable systems; testing
DIN 4102-12:1998
Leakage test for rectangular section air ducts UNE-EN 1507:2007
Leakage test for circular section air ducts UNE-EN 12237:2003 UNE-EN 12237:2003 ERRATUM:2007
Insulating products Determination of organic content UNE-EN 13820:2008
Fire safety storage cabinets Fire resistance test for safety storage cabinets for flammable liquids
UNE-EN 14470-1:2005 Annex A
Acreditation nº 41/LE104 Technical Annex Updated
Page 8 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
PART C: Fire fighting systems and equipments (1)
Pillar fire hydrants Verification of overall dimensions, visual checking,
documental checking and marking
UNE-EN 14384:2006 Sec. 1, 4.1, 4.2, 4.3, 4.4, 4.5, 4.9, 4.11, 4.12, 4.13, 4.15, 4.16, 4.17, 4.19, 5.2 and 6.2
Leak tightness and mechanical resistance of the hydrant body and other pressure containing components
UNE-EN 14384:2006 Sec.4.6.2 UNE-EN 1074-1:2001 Annex A
Leak tightness and mechanical resistance of the main valve
UNE-EN 14384:2006 Sec.4.6.3 UNE-EN 1074-1:2001 Annex B
Opening turns UNE-EN 14384:2006 Sec. 4.8 and 4.9
Maximum operating torque UNE-EN 14384:2006 Sec. 4.10.1 UNE-EN 1074-6:2004 Annex C
Minimum operating torque UNE-EN 14384:2006 Sec. 4.10.2 UNE-EN 1074-2:2001 Annex A
Drain and vent systems UNE-EN 14384:2006 Sec. 4.14 UNE-EN 1074-6:2004 Sec. 5.6
Resistance to disinfectants UNE-EN 14384:2006 Sec. 4.18 UNE-EN 1074-1:2001 Sec. 5.4 and Annex E
Pressure drop UNE-EN 14384:2006 Sec.4.20 and 5.3
Underground fire hydrants Verification of overall dimensions, visual checking,
documental checking and marking
UNE-EN 14339:2006 Sec. 1, 4.1, 4.2, 4.3, 4.4, 4.5, 4.6, 4.8, 4.11, 4.12, 4.13, 4.15.1, 4.15.2, 4.15.3, 4.17 and 6.1
Leak tightness and mechanical resistance of the hydrant body and other pressure containing components
UNE-EN 14339:2006 Sec.4.7.2 UNE-EN 1074-1:2001 Annex A
Leak tightness and mechanical resistance of the main valve
UNE-EN 14339:2006 Sec.4.7.3 UNE-EN 1074-1:2001 Annex B
Opening turns UNE-EN 14339:2006 Sec.4.8 and 4.9
Maximum operating torque UNE-EN 14339:2006 Sec.4.10.1 UNE-EN 1074-6:2004 Annex C
Minimum operating torque UNE-EN 14339:2006 Sec.4.10.2 UNE-EN 1074-2:2001 Annex A
Drain and vent systems UNE-EN 14339:2006 Sec.4.14 UNE-EN 1074-6:2004 Sec. 5.6
Acreditation nº 41/LE104 Technical Annex Updated
Page 9 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Underground fire hydrants (continued)
Resistance to disinfectants UNE-EN 14339:2006 Sec.4.16 UNE-EN 1074-1:2001 Sec. 5.4 and Annex E
UNE-EN 671-1:2013 Sec. 5.3.3, 5.3.4, 5.3.5, 5.3.6, 5.4 and Annexes F.1, F.2, F.3, F.4, F.5 and F.6
Mechanical resistance: resistance to internal pressure and breaking strength
UNE-EN 671-1:2013 Sec. 5.3.12, 5.3.13 and Annexes F.7 and F.8 UNE-EN 671-2:2013 Sec. 5.3.6, 5.3.7 and Annex F
Portable fire extinguishers
Specifications UNE-EN 3-7:2004+A1:2008 Sec. 4
Nominal charges, filling tolerances and minimum fire performance
UNE-EN 3-7:2004+A1:2008 Sec. 6
Duration of operation, residual charge and commencement of discharge
UNE-EN 3-7:2004+A1:2008 Sec. 3.2, 7.1, 7.2, 7.3 and Annex A
Operating temperatures UNE-EN 3-7:2004+A1:2008 Sec. 7.4, Annex B
Acreditation nº 41/LE104 Technical Annex Updated
Page 12 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Portable fire extinguishers (continued)
Retention of propellant UNE-EN 3-7:2004+A1:2008 Sec. 8
Settlement UNE-EN 3-7:2004+A1:2008 Sec. 5 and Annex K
Requirements for components and additional requirements
UNE-EN 3-7:2004+A1:2008 Sec. 10
Means of pressure indication UNE-EN 3-7:2004+A1:2008 Sec. 11
Horns for carbon dioxide portable fire extinguishers
UNE-EN 3-7:2004+A1:2008 Sec. 12
Portable fire extinguisher mounting brackets UNE-EN 3-7:2004+A1:2008 Sec. 13
Resistance to external and internal corrosion UNE-EN 3-7:2004+A1:2008 Sec. 14
Colour and marking UNE-EN 3-7:2004+A1:2008 Sec. 16 UNE 23110-3: 1994. Sec. 7, 9.1.3 and 9.2.3
Checking of components under pressure
UNE 23110-3:1994 Sec. 5.2 and 10.3 Directive 84/525/CEE. Annex I, Sec. 2.2 Directive 84/526/CEE. Annex I, Sec. 2.3
Bottles and gas small bottles construction checking UNE 23110-3:1994 Sec. 5.3.2, 9.2.1 and 12.3
Device pressure, breakage under pressure and test to the test pressure Pmax < 500 bar
UNE 23110-3:1994 Sec. 6.1, 6.3, 9.1.2, 9.2.2 Directive 84/525/CEE. Annex I, Sec. 3.2 and 3.4 Directive 84/526/CEE. Annex I, Sec. 3.2 and 3.4
Bursting discs of CO2 portable fire extinguishers UNE 23110-3:1994 Sec. 12.2
Mechanical resistance UNE 23110-3:1994 Sec. 6.2
Bodies. Minimum wall thickness UNE-EN 3-8:2007 Sec. 6.2.1
Bodies. Requirements for the base UNE-EN 3-8:2007 Sec. 6.2.2
Burst test under pressure UNE-EN 3-8:2007 Sec. 6.3.2
Mechanical resistance test (crushing test and impact resistance)
UNE-EN 3-8:2007 Sec. 6.3.3, 6.5.2 and Annex C
Pressure test UNE-EN 3-8:2007 Sec. 6.3.4, Annexes E.1.2, E.2.2 and F.2
Acreditation nº 41/LE104 Technical Annex Updated
Page 13 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Portable fire extinguishers (continued)
Pressure test. Pressure gauges and pressure indicators
UNE-EN 3-8:2007 Sec. 6.3.5
Overfill pressure test UNE-EN 3-8:2007 Sec. 6.4 and Annex G
Cylinder and operating devices UNE-EN 3-9:2007 Sec. 5.1
Filling ratio UNE-EN 3-9:2007 Sec. 5.2
Operating device UNE-EN 3-9:2007 Sec. 5.3 and Annex C
Bursting disc UNE-EN 3-9:2007 Sec. 5.4
Hose and nozzle couplings. Prototype testing UNE-EN 3-9:2007 Sec. 5.5
Resistance to impact UNE-EN 3-9:2007 Sec. 5.6 and Annex D
Manufacturing of the assembled extinguisher UNE-EN 3-9:2007 Sec. 6
Marking UNE-EN 3-8:2007 Sec. 9, Annex E.3 and F.3 UNE-EN 3-9:2007 Sec. 8
Effectiveness in fires type F UNE-EN 3-7:2004 + A1 :2008 Sec. 15.1, 15.4 and Annex L
Portable fire extinguishers
Operating temperatures
UNE-EN 1866:2007 Sec. 6.1, 11. and Annex D.6 UNE-EN 1866-1:2008 Sec. 6.1 and Annex A.6
Nominal charges, filling tolerances and propelling agents
UNE-EN 1866:2007 Sec. 6.2 and 6.8 UNE-EN 1866-1:2008 Sec. 6.2
Duration of operation, residual mass and discharge range
UNE-EN 1866:2007 Sec. 6.3 and Annex D.2 UNE-EN 1866:2008 Sec. 6.3 and Annex A.2
Retention of charge UNE-EN 1866:2007 Sec. 6.4 UNE-EN 1866-1:2008 Sec. 6.4
Leakage of the control valve
UNE-EN 1866:2007 Sec. 6.5 and Annex D.5 UNE-EN 1866-1:2008 Sec. 6.5 and Annex A.5
Hose and coupling UNE-EN 1866:2007 Sec. 6.7 and Annex F
Acreditation nº 41/LE104 Technical Annex Updated
Page 14 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Portable fire extinguishers (continued) Operation devices. Working position, generals and
jet control mechanisms devices
UNE-EN 1866:2007 Sec. 6.6, 6.9.1 and 6.9.2 and Annexes D.3, D.4 y D.5 UNE-EN 1866-1:2008 Sec. 6.6, 6.7, 6.8.1 and 6.8.2 and Annexes A.3 and A.4
Safety devices UNE-EN 1866:2007 Sec. 6.9.3 UNE-EN 1866-1:2008 Sec. 6.8.3
Discharge from water, water base and foam extinguishers
UNE-EN 1866:2007 Sec. 6.9.4 UNE-EN 1866-1:2008 Sec. 6.8.4
Leakage and operating tests of pressure gauges UNE-EN 1866:2007 Sec. 6.9.5 UNE-EN 1866-1:2008 Sec. 6.8.5
Verification of design characteristics of the filling opening and other dimensions of the extinguisher
UNE-EN 1866:2007 Sec. 6.9.6 UNE-EN 1866-1:2008 Sec. 6.8.6
Identification UNE-EN 1866:2007 Sec. 6.10 UNE-EN 1866-1:2008 Sec. 6.9
Wall thickness UNE-EN 1866:2007 Sec. 8.2
Hydrostatic pressure test UNE-EN 1866:2007 Sec.8.3.1
Burst test UNE-EN 1866:2007 Sec. 8.3.2
Overfill pressure test UNE-EN 1866:2007 Sec. 8.6
Pressure test for components UNE-EN 1866:2007 Sec. 8.7
Marking UNE-EN 1866:2007 Sec. 9.3.2 and 9.3.3
External corrosión test (salt spray test) UNE-EN 1866:2007 Sec. 11.2.1 UNE-EN 1866-1:2008 Sec. 7.2.1
Internal corrosión test
UNE-EN 1866:2007 Sec. 11.2. and Annex D.7 UNE-EN 1866-1:2008 Sec. 7.2.2 and Annex A.7
Class B fire test UNE-EN 1866:2007 Sec.12.2 UNE-EN 1866-1:2008 Sec. 8.2
Plastic components. Burst under pressure and resistance to temperature
UNE-EN 1866:2007 Sec. Annexes B.2.2 and B.2.3
Coupling for fire hose
Connection, Tightness, cork test, anodising and sealing
UNE 23400-5:1998 UNE 23400-5:1999 Erratum Sec.6.1.1,6.1.2, 6.1.3 y 6.2.2 UNE-EN ISO 2143:2011
Acreditation nº 41/LE104 Technical Annex Updated
Page 15 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Hand-held branchpipes for fire service use: Combination branchpipes PN16 Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16 High pressure branchpipes PN 40
Marking UNE EN 15182-1:2007+A1:2010 Sec. 8.2
Common requirements to design
UNE-EN 15182-1:2007+A1:2010 Sec. 4, 6.1.1, 6.1.2, 6.1.3.1, 6.1.3.2, 6.1.3.3, 6.1.3.4, 6.1.3.5, 6.1.3.6 and 6.3 UNE-EN 15182-2:2007+A1:2010 Sec. 4.2.2.1, 4.2.2.2, 4.2.2.3, 4.2.3 and 4.2.4 UNE-EN 15182-3:2007+A1:2010 Sec. 4.2.2.1, 4.2.2.2 and 4.2.3 UNE-EN 15182-4:2007+A1:2010 Sec. 4.2.2.1, 4.2.2.2, 4.2.3 y 4.2.4
Dimensions y mass
UNE-EN 15182-1:2007+A1:2010 Sec. 6.1.2 UNE-EN 151822:2007+A1:2010 Sec. 4.2.1 UNE-EN 15182-3:2007+A1:2010 Sec. 4.2.1 UNE-EN 15182-4:2007+A1:2010 Sec. 4.2.1
Torques for operating elements
UNE-EN 15182-2:2007+A1:2010 Sec. 4.2.2.1 UNE-EN 151823:2007+A1:2010 Sec. 4.2.2.1 UNE-EN 15182-4:2007+A1:2010 Sec. 4.2.2.1
Heat and frost test UNE-EN 15182-1:2007+A1:2010 Sec. 7.2
Drop test UNE-EN 15182-1:2007+A1:2010 Sec. 7.3
Flushing UNE-EN 15182-1:2007+A1:2010 Sec. 6.3 y 7.4
Jet spray angle
UNE-EN 15182-2:2007+A1:2010 Sec. 5.2 UNE-EN 151823:2007+A1:2010 Sec. 5.2 UNE-EN 15182-4:2007+A1:2010 Sec. 5.2
Flow and throw test
UNE-EN 15182-2:2007+A1:2010 Sec. 5.3 UNE-EN 151823:2007+A1:2010 Sec. 5.3 UNE-EN 15182-4:2007+A1:2010 Sec. 5.3
Leak-tightness
UNE-EN 15182-2:2007+A1:2010 Sec. 4.4 y 5.4 UNE-EN 15182-3:2007+A1:2010 Sec. 4.4 and 5.4 UNE-EN 15182-4:2007+A1:2010 Sec. 4.4 and 5.4
Acreditation nº 41/LE104 Technical Annex Updated
Page 16 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Hand-held branchpipes for fire service use: Combination branchpipes PN16 Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16 High pressure branchpipes PN 40 (Continued)
Hydrostatic test
UNE-EN 15182-2:2007+A1:2010 Sec. 5.5 UNE-EN 15182-3:2007+A1:2010 Sec. 5.5 UNE-EN 15182-4:2007+A1:2010 Sec. 5.5
Regulation range
UNE-EN 15182-2:2007+A1:2010 Sec. 4.3.6 UNE-EN 151824:2007+A1:2010 Sec. 4.3.6
Nozzles for CO2 systems Compliance
UNE-EN 12094-7:2001 Sec. 5.3 UNE-EN 12094-7:2001/A1:2005
Verification of flow rate UNE-EN 12094-7:2001 Sec.5.5 UNE-EN 12094-7:2001/A1:2005
Test for resistance to pressure and heat UNE-EN 12094-7:2001 Sec. 5.6 UNE-EN 12094-7:2001/A1:2005
Test for resistance to heat and cold shock UNE-EN 12094-7:2001 Sec. 5.7 UNE-EN 12094-7:2001/A1:2005
Nozzle protection device UNE-EN 12094-7:2001 Sec. 5.8 UNE-EN 12094-7:2001/A1:2005
Test for resistance to corrosion UNE-EN 12094-7:2001 Sec. 5.9 UNE-EN 12094-7:2001/A1:2005
Test for resistance to stress corrosion UNE-EN 12094-7:2001 Sec.5.10 UNE-EN 12094-7:2001/A1:2005
Marking UNE-EN 12094-7:2001 Sec. 6 UNE-EN 12094-7:2001/A1:2005
Connectors for gas extinguishing systems
Compliance UNE-EN 12094-8:2007 Sec. 5.3
Test for resistance to leakage UNE-EN 12094-8:2007 Sec. 5.4
Test for resistance to bursting UNE-EN 12094-8:2007 Sec. 5.5
Test for resistance to pressure and heat UNE-EN 12094-8:2007 Sec. 5.6
Test for resistance to heat and cold shock UNE-EN 12094-8:2007 Sec. 5.7
Test for resistance to cold UNE-EN 12094-8:2007 Sec. 5.8
Test for resistance to flexing UNE-EN 12094-8:2007 Sec. 5.9
Marking UNE-EN 12094-8:2007 Sec. 6
Acreditation nº 41/LE104 Technical Annex Updated
Page 17 of 18
PRODUCT/MATERIAL TO BE TESTED
TEST TEST STANDARD/PROCEDURE
Pressure gauges and pressure switches for gas extinguishing systems
Compliance UNE-EN 12094-10:2004 (Secs. 5.1.2 and 5.2.3)
Operation UNE-EN 12094-10:2004 Sec. 5.2.4
Internal pressure UNE-EN 12094-10:2004 Sec. 5.2.5
Operational reliability UNE-EN 12094-10:2004 Sec. 5.2.6
Temperature UNE-EN 12094-10:2004 Sec.5.2.7
Corrosion UNE-EN 12094-10:2004 Sec. 5.2.8
Marking UNE-EN 12094-10:2004 Sec. 6
Check valves and non-return valves for gas extinguishing systems