TANK Design and Detailing

8/11/2019 TANK Design and Detailing

1/17

TANK DESIGN & DETAILING

Introduction

The API 650 standard is designed to provide the petroleum industry with tanks of adequate safety and reasonable

economy for use in the storage of petroleum, petroleum products, and other liquid products commonly handled and

stored by the various branches of the industry. This standard does not present or establish a fixed series of

allowable tank sizes; instead, it is intended to permit the purchaser to select whatever size tank may best meet his

needs. This standard is intended to help purchasers and manufacturers in ordering, fabricating, and erecting tanks; itis not intended to prohibit purchasers and manufacturers from purchasing or fabricating tanks that meet

specifications other than those contained in this standard.

This standard has requirements given in two alternate systems of units. The requirements are similar but not

identical. These minor differences are due to issues such as numerical rounding and material supply. When

applying the requirements of this standard to a given tank, the manufacturer shall either comply with all of the

requirements given in SI units or shall comply with all of the requirements given in US Customary units. The

selection of which set of requirements (SI or US Customary) shall apply to a given tank shall be by mutualagreement between the manufacturer and purchaser.

Types of tanks (based on Roof fixing)

1. Fixed Roof Tank2. Floating Roof Tank

Types of Tank based on Roof

1. Flat Roof2. Cone Roof

3. Domed Roof

Types of Floating Roof Tanks

1. Internal Floating Roof Tank


2/17

2. External Floating Roof Tank

Mani Parts of Tank

1. Tank Shell2. Bottom plate

3. Annular Plate4. Backing strip

5. Anchor chairs and Anchor bolt arrangements6. Draw of sump

7. Cleanout catch8. Nozzles

9. Shell man way10. Roof man way

11. Fire safety12. Primary & Secondary Wind girder

13. Curb angle or compressen ring14. Roof plate

15. Crown plate

16. Vent Nozzles17. Overflow pipes18. Roof Structures and support structures

19. Internal pipe supports20. Internal man way rungs and internal ladder with support clips

21. External cage Ladder and spiral Staircase ladders and platforms with support clips22. Roof handrails

For Floating Roof tanks

1. Drain system2. Double Deck or single Deck

3. Seal or foum4. Pantoon Legs

5. Deck legs6. Rim plate & rim pantoons

7. Rollin ladder8. Pantoon man way

9. Deck man way


3/17

Standards:

API Standard 650, Welded Steel Tanks for Oil Storage

API Standard 620, Recommended Rules for Design and Construction of Large Welded LowPressure Storage Tanks

API RP 2000, Venting Atmospheric and Low Pressure Storage Tanks

Standard Selection conditions:

Atmospheric pressure no refrigerated tanks shall be designed to API 650. Closed Top subjectto low pressure shall additionally satisfy Appendix F.

Higher pressure tanks up to 15 psig shall comply with API 620 and shall include all API 650requirements for materials and examinations.

API 650 tanks with wall thickness up to and including 0.5 inch shall be to Appendix A except

that Group I materials of Table 2-3 shall not be used below 20F.

Shop assembled API 650 tanks shall comply with Appendix J except that a minimum of spot

radiography shall be applied with joint efficiency of 0.85.

1. TANK GA PREPARATION:

1. Fix the layout for tank overall dimensions in elevation, top view and side view.2. Compare the overall dimensions and reference dimensions

3. To draw all the attachments and tank parts should be maintain completely 1:1 scale4. Put all the orientation for Man ways , draw of sump, Nozzles and internal and external ladder

clips, earthing boss or Clips, wind girder, lightning clips, piping support clips and etc.5. All nozzle sizes and standards, schedules, type of flanges to be used, type of faces to

Be used in flanges, if required any blind flanges, Davit Man ways, hinged type man ways,Vent and all nozzle elevation should be Fixed in Bottom of tank (bottom of shell plate). These

items should be come in nozzle Details.6. General notes, assembly notes are added in notes.

7. Which type of materials used in tank and attachment parts is come in material of Construction.

8. Add the design notes in Design Data table


4/17

9. Total weight of the tank and centre of gravity should be added.10. If any internal (or) external surface preparation is there, this notes also added.11. Client gives any standards to be follow the tank detailing, that standard also should

Give the Standard requirements12. If any tolerance given, that is also added in overall dimensions

13. Structural also added in the GA drawing.14. If any legends there these items also include

Major dimensions specified in GA Drawing

1. Tank total height

2. Tank ID3. Tank plate thickness in via course

4. If any wind girder is there that elevation should be added5. Nozzle orientations and ladder positions (internal or external), ladder clips

And piping supports, all attachments. etc6. Nozzle elevations (X,Y) minimum two dimensions

7. If Roof Nozzle there, that case angel and distance for center line of tank

8. Structural column to column distances overall length for columns9. Sump Orientation

SURFACE PREPARATION AND PAINTING: (Example)

SURFACE PREPARATION AND PAINTING

Design Data (example):


5/17

NOZZLE DATAS: (Example)

STANDARDS, SPECIFICATIONS: (Example)

MATERIAL OF CONSTRUCTION: (Example)


6/17

Pressure rating

Design pressures up to 500 mbar:

Non-pressure, up to 10 mbarLow-pressure, up to 25 mbar

High-pressure, up to 60 mbarVery high-pressure, up to 500 mbar

Maximum negative pressure = -20 mbar.

Valid for negative pressure = up to -8.5 mbar

Temperature range is from 300C down to -40C.

SHELL DEVELPOMENT DRAWING

Vertical Joints in Shell

Butt joints with complete penetration and complete fusion as attained by

double Welding or by other means which will obtain the same quality of jointHorizontal Joints in ShellComplete penetration and complete fusion butt weld.

Shell to Bottom Plate JointContinuous fillet weld laid on each side of the shell plate. The size of each weld

shall be the thickness of the thinner plate.

1. Shell plate development detail (use pi * D formula, D is mean dia of tank)2. Cutting layout drawing

3. Shell plate to Annular plated welding detail4. shell plate to Shell plate (longitudinal and circumference) welding details

5. Wind Girder to shell plate welding detail6. Wind Girder to Wind girder welding details

7. Curb angle to shell plate welding detail8. Bill of materials

9. General notes10. Section Views for plate to plate welding details

Shell plate Development Drawing involved components

1. Nozzle od and Rf pad od locations and dimensions

2. Man way od and man way Rf pad od locations and clean out catch

3. Earthing Boss or clips locations and overall dimensions4. Lightening clips, Piping supports clips (X or Y dimension and plate weld line to clip enddimension

5. Wind Girder positions and welding joints6. Curb angle locations

7. Internal and external ladder clips locations


7/17

Shell course design details one foot method (example)

Allowable steel stresses:

To keep the selection of shell plate material within the band ofcarbon and carbon manganese

weldable steels the maximum allowable design stress which may be used is 260 N/mm2 or twothirds of the material, specified minimum yield strength at room temperature, whichever is the

lower. This limit of 260 N/mm'discourages the use of steels with a minimum specified yield strength in excess of390 N/mm2,

because of their increased hardness and reduced weldability.

(CL 3.6.3.2, TABLE 3.2 & CL 3.6.1.1 Note:1of API-650)tt= 4.9 D (H-0.3)/St - Hydro test thick

td= 4.9 D (H-0.3)G/Sd + CA Design calculated thick.

D Dia of tank

H Design Liquid levelG Specific gravity of liquid

Sd 2/3 of yield stress 2/5 of tensile stress

Less value only taken

St 3/4 of yield stress 3/7 of tensile stress

Less value only taken

Thickness of the bottom course or ring, which is restricted by API 650 to a

maximum of1 inch.

Shell course(Number from

Bottom most)

Considered

Material

Specification

Ht ofCourse

(m)

AssumedThickness (mm)

Nominal

Tank Dia

(m)

Ht fromBottom of

Courses to

Bottom of

overflownozzle (m)

Sd

(Mpa)

(C.A)

(mm)

Cal.

Thick

(mm)

Hydro

test

Thick

(mm)

Provided

Ht(m)xThk.(mm

course

First (Bottom

most)S355 J 2 G 3 FF 2.5 12 36.012 11.719 196 1.5 11.57 9.6 2.5mx12m

Second S355 J 2 G 3 FF 2.5 10 36.010 9.219 196 1.5 9.37 7.5 2.5mx10m

Third S355 J 2 G 3 FF 2.5 8 36.008 6.719 196 1.5 7.16 5.4 2.5mx8m

Fourth S235 JRG 2 FN 1.5 6 36.006 4.219 157 1.5 5.82 4.04 1.5mx6m

Fifth S235 JRG 2 FN 1.5 6 36.006 2.719 157 1.5 4.16 2.50 1.5mx6m

Sixth S235 JRG 2 FN 1.425 6 36.006 1.219 157 1.5 2.51 0.95 1.425mx6


8/17

Major Dimensions specified:

1. Overall length

2. Course length3. circumference length

4. orientation angle5. between angles length

6. weld to weld distance (longitudinal and circumference) length7. weld Gap (longitudinal and circumference)

8. Nozzle positions angles and distance9. Attachments and all types of clips positions and angles

10. welding details should be maintain weld sizes, welding angles, which type of weld shouldbe used

11. part no. in all plates, curb angle, all attachment clips with out nozzle and nozzle pads12. If any legends there these items also include

BOTTOM PLATE DEVELOPMENT

Bottom Plates

Single-welded full-fillet lap joint or single-welded butt joint with backing strip.The bottom plates shall project at least 1inch width beyond the outside edge of the weld

attaching the bottom to shell plate1. Bottom plate development drawing

2. Cutting layout drawing3. plate to plate welding detail

4. three plate welding detail5. Bottom plate to Annular plate and Back strip welding detail

6. Section Views for plate to plate welding details7. Bill of materials

8. General Notes

DESIGN OF BOTTOM PLATE:

(CL 3.4.1 of API-650) and BS 2654Bottom plate thickness = 6mm + C.A

Min plate thickness forStainless steel tanksLap welded bottom plate = 5tmm

But welded bottom plate = 3mm

Min plate thickness forCarbon steel tanksLap welded bottom plate = 6mm

But welded bottom plate = 5mm


9/17

DESIGN OF ANNULAR PLATE:

(CL 3.5.3 & Table 3.1 of API-6500)

Hydrostatic Stress 4.9 x D x H - 0.3

THK (example)

4.9x 36.012x 11.719 0.312

= 167.92 < 210 (210 is material allowable stress in design temperature)

Hydrostatic Stress < 210 Mpa

Annular Plate Thickness provided = 12mm

Annular plate width

(CL 3.5.2 of API-650)

Annular plate radial width = 215 tb / (HG)0.5

Min radial width will be maintain 600 mm as per Cl 3.5.2

tb = Thickness of the annular plate in mm

H = Maximum design liquid level

G = Design specific gravity of the liquid to be stored


1. Overall developed OD

2. plate course width3. welding gap

4. Center of Bottom plate to middle plate fixing dimensions(vertical & horizontal)5. Bottom plate slope

6. Type of weld, welding size and welding angle7. plate edge preparation dimensions in welding detail

8. If any draw of sump is there that is also put the weld detail


10/17


11/17

ROOF PLATE DEVELOPMENT

Roof Plates

Single-welded full-fillet lap joint. Roof plates shall be welded to the top angle of the tank with continuous fillet weld on the top side only.

1. Roof plate development drawing2. Cutting layout drawing

3. plate to plate welding detail4. Section Views for plate to plate welding details

5. Bill of materials6. General Notes

7. Crown plate to Roof plate detail

Types of Roofs

1. Fixed Roof 1. Cone Roof

2. Doom Roof

3. Umbrella Roof2. External floating roofs1. Types of external floating roof

1. Single-deck pontoon type2. Double-deck type

2 Other types of floating roof1. BIPM roof

2. Buoy roof3 Internal floating roofs

1. Types of internal floating roofs1. Pan roof

2. Honeycomb roof3. Pontoon and skin roof

DESIGN OF ROOF PLATE:

For CONE

t = D/400 sin

t = in (Max)

= 37 deg (9:12 slope)= 9.28 deg (2:12 slipe)

Fro DOOM

t = R/200 but not lesser than 3/16 int = in

R = 0.8 D (min)R = 1.2D (max)

Unless otherwise specified by the purchaser

(Cl 3.10.2.2 of API-650 )

Minimum Thickness of Roof Plate = 5mm + C.AConsidering the Bottom Plate Thickness as 6mm.

Roof plate Thickness provided min = 5mm


12/17


1. Overall developed OD2. Plate course width

3. Welding gap

4. Center of Roof plate to middle plate fixing dimensions (vertical & horizontal)5. Roof plate slope

6. Type of weld, welding size and welding angle7. Plate edge preparation dimensions in welding detail

8. Roof Nozzles, RF pads, Roof man ways, positions and angles9. Roof cutting angle

10. Crown plate cutting angle.

CUTTING ANGLE CALCULATION:

(R / r * 360) - 360

NOZZLE DETAILING

1. Nozzle and Man way weld details

2. Nozzle design as per CL 3.7 in API 650 follow

Reinforce nozzle welding detail (example)


13/17

DETAIL OF LONG WELD NECK NOZZLE & NOZZLE WITH RF PAD

Lesser than 3 and 250 and above lg provide Stiffener plate 2 no apart90 deg in 45 deg angle


14/17

Manways

The number of manways to be provided are shown in the table below:

TANKNOMINALDIA. (FT)

MANWAYSIN SHELL

MANWAYSFIXED ROOF

IN ROOFFLOATING ROOF

DECK

Up to 20 1 - 24 inch 1 - 24 inch 1 - 30 inch

over 20 to 60 2 - 24 inch 1 - 24 inch 1 - 30 inch

over 60 to 120 3 - 24 inch 1 - 24 inch 2 - 30 inch

over 120 2 - 24 inch

1 - 30 inch

2 - 24 inch 2 - 30 inch

Floating roofs

Types

1. Metallic pan roofs:

These are in contact with the liquid and have peripheral rim

2. Metallic bulkhead roofs:These are in contact with the liquid and have open top bulkheads.

3. Metallic pontoon roofs

These are in contact with the liquid and have closed pontoons

4. Metallic double - deck roofs:

These are in contact with the liquid

5. Metallic roof on floats:

These roofs have their deck above the liquid.

6. Metallic sandwich panel roofs:

These have surface coated honeycomb panels and are in contact with the

liquid

7. Plastic sandwich panel roofs:These are surface coated rigid panels and are in contact with the liquid

8. Roof seals design shall:

1. Be sufficiently flexible and have sufficient range of movement toaccommodate roof movements and flexing of the roof and tank wall.

2. Remain stable in sunlight, tank liquid, tank vapour etc.

3. Prevent contact between organic materials and the tank contents.

4. Have metallic components galvanised unless otherwise agreed.

5. Ensure contact between seal and shell above liquid level. Shoe type seals tohave 90% minimum contact and flexible seal type 100% minimum contact. No

gap shall exceed 0.25 inch or be circumferentially longer than 48 inches.

6. Include primary and secondary seals unless otherwise agreed.

7. Include rim seal vents.

8. Sleeves for leg supports shall remain above liquid level when the deck is fullydeflected.

9. Internal floating roofs shall comply with API 650 Appendix H except thatminimum thickness shall be 6mm for aluminium and stainless steel. Pan type

floating roofs shall not be used. Fixed internal ladders are not permitted.


15/17

Tank Height to Dia ratio by Sesmic Zone

Sesmic Zone Max tank height (Height to Dia ratio)

1 2.4:1

2 1.25:1 3 0.67:1

4 0.5:1 (Small tank, soft soil) 4 0.6:1 (large tank, firm soil)

Rectangular TanksRatio of sides

The sides are equal

B = 3 root of V

V = Volume

If Rectangular

Length = 1.5 B

Width = 0.667 B

Welding for corer plates (welding size 0.75 x Thick of min size plate)


16/17

Materials selection

Nominal composit ion Criteria

C Steel Plain Carbon steelC Si Steel Exceed 0.1%SiliconC Mn Steel Exceed 1.0%MangneseC Mo Steel Carbon with molybdenum added at the midpoint of the

Range specified

C Mn Si Steel

I. Selection of Materials for Service Environment

1. Design Factors

Design factors to consider include: Operating temperature and pressure Service environment Cost Design life Reliability and safety

2. Typical selections3. Application Criteria for Common Pressure Vessels Materials4. Summary of Temperature Limitations

II. Selection of Materials for Brittle Fracture Prevention

1. Definition of Brittle Fracture2. Design to Prevent Brittle Fracture3. Recommended Practice for Selecting Steels for New Construction of Pressure Vessels4. Typical Carbon Steel Selections to Avoid Brittle Fracture in Pressure Vessels5. Steel Selection for Pressure Vessels Subject to Auto refrigeration6. Factors Controlling Susceptibility to Brittle Fracture: Additional Technical Information

III. Material Selections idias and construction

1. Determine Minimum design metal temperature (MDMT).2. Determine Minimum pressuring temperature (MPT)

3. Maximum allowable stress values shall be in accordance with the API Standard, section 3.6.2 Table 3.2.

4. For austenitic stainless steel tanks the allowable stress shall be to the rules of API 620 Appendix Q

5. Annular bottom plates shall be to the same material specification and grade as the bottom shellcourse.

6. Cast fittings shall not be used in the shell or bottom of the tank

7. For stainless steel tanks to API rules, the material specifications and allowable stress rules of API 620Appendix Q shall be used.

8. Corrosion allowance shall be added to the minimum annular plate thicknesses of API 650 Table 3-1.

9. Minimum thicknesses of internal structural members shall be 6mm plus corrosion allowance.

10. Wind girders on floating roof tanks shall be 3 feet 6 inches below the top of the curb angle and shallhave a minimum width of 18 inches outside the curb angle. If used as a walkway the girder shallcomply with API 650 paragraph 3.9.4.

11. For stainless steel tanks the wind girder section modules of API 650 shall be multiplied by 21000/S,where S is the stainless steel design stress (psi).

12. Fixed roof API 650 tanks shall have a frangible joint between the top angle and the roof plates.

13. For fixed roof pressurised design to API 650 Appendix F the area formula in F.5. shall also bemultiplied by 24000/S, for stainless steel design.

14. For Floting roof Bearing plates 0.375 inches thick shall be provided under each support leg.

15. For Floting roof Thickness of the outer rim shall be 0.25 inches plus corrosion allowance minimum.

16. Roof decks shall be continuously welded from the top side and pontoon bulkheads shall be welded atthe top to be vapour tight.


17/17

17. A continuous foam dam shall be provided on tanks 100 feet diameter and over. The dam shall be of0.187 inch plate and shall be to NFPA No. 11 Appendix A-3.2.11.1.

Information to be specified by the purchaser

1 The following basic information to be specified bythe purchaser shall be fully documented. Boththe definitive requirements specified throughout the Standard and the documented items shall besatisfied before a claim of comoliance with the Standard can be made and verified.

2 (a) Geographical location of the tank.

3 (b) Diameter and height or the capacity of the tank, including ullage. Where only the capacity ofthe tank is specified

4 Ground conditions shall be included.

5 (c) Whether fixed or floating roof into be supplied and the type of roof if the purchaser has specificpreferences, i.e. for Fixed roofs (cone, dome, membrane, etc.) or floating roofs (pontoon, doubledeck, etc.).

6 (d) All relevant properties of the contained fluid, including the relative density and corrosionallowance (if, how and Where required).

7 (e) The design vapor pressure and vacuum conditions inside the tank

8 (f) The minimum and maximum design metal temperatures

9 (g) The size, number and type of all mountings required showing locations. Maximum filling andemptying rates And any special venting arrangement

10 (h) The minimum depth of product which is always present in the tank

11 (i) lf the tank is to be thermally insulated

12 0) Areas of responsibility between the designer, the manufacturer and the erector ofthe tank whenthese are not the same.

13 (k) Quality ofthe water to be used during tank water test

14 (l) Expected maximum differential settlements during water testing and service lifetime of the tank(see AppendixA).

15 (m) Other specifications which are to be read in conjunction with this Standard.

For Refernece

1. Guide to storage tanks and equipment design by: Bob Long and Bob Garner2. API 650 Standard

Prepared by

I.ROBERT ANTO RENI.

TANK Design and Detailing

Documents