HD HOME SECURITY ACCESSORY CAMERAInstallation Guide
For the complete system guide...On your computer, go to
http://bit.ly/2DeLr3J or scan the QR code here.
Step 1: Unpack
(1) Mounting Template
(1) HD Indoor/Outdoor Security Camera
(3) Mounting Screws and Anchors
Step 2: Mount the cameraNote: This security camera can be both
wall- and ceiling-mounted. The installation instructions that
follow are for ceiling mounting, but they can be adapted for wall
mounting as well.
4. Route the cables from the camera through the cable hole or
through the side outlet on the camera base.
5. Secure the camera to the ceiling or wall with the supplied
screws (and anchors, for brick or stucco).
For pan adjustment: Loosen the base ring and pan up to 360º.
Tighten the base ring when you have the camera panned the way you
want.
For arm tilt adjustment: Loosen the arm screw and tilt the arm
up to 180º. Tighten the screw when you have the arm in the position
you want.
For camera rotation adjustment: Loosen the camera screw and
rotate the camera up to 360º. Tighten the screw when you have the
camera in the position you want.
Make sure the base ring and adjustment screws are tightened all
the way for each camera before proceeding.
Base ring (pan)
Arm screw (tilt)Camera screw
(rotation)
1. Apply the mounting template sticker to the ceiling where you
want to mount the camera.
2. Mark the location for the mounting holes.
3. Drill screw holes (labeled 1 on the template) and the cable
hole (if desired, labeled A) where marked.
Use the following drill bit sizes:
brick or stucco = 7/32”wood surface = 1/16”
Side outlet
Adjust the camera’s position to get the angle you want.
Step 3: Orient the camera
Step 4: Connect the camera to your DVR1. Match the video and
power cables from the
camera to one end of the provided BNC cable and connect
them.
12
34
56
78
VIDEO IND+ D-RS-485
VGA IN
OUTAUDIO LAN&USB 12V
Camera BNC
2. Plug the video output cable on the other end of this BNC
cable into one of the VIDEO IN jacks on the back of the DVR.
3. Plug the power input cable on the other end of this BNC cable
into the camera power adapter.
4. Plug the camera power adapter into a working outlet or surge
protector.
DVR back panel
(1) 60ft BNC Cable
(1) Camera Power Adapter
Camera power
adapter
HSCAM2 QSG 01
© 2018 Voxx Accessories Corp. 3502 Woodview Trace, Suite 220
Indianapolis, IN 46268
www.RCAAudioVideo.com
CAMÉRA ACCESSOIRE HD DE SÉCURITÉ POUR LE DOMICILEGuide
d’installation
Pour le guide du système complet...Sur votre ordinateur, aller
sur http://bit.ly/2DeLr3J ou balayer le code QR ci-contre.
Étape 1 : Déballer
(1) Gabarit de montage
(1) Caméra de sécurité HD intérieure/extérieure
(3) Vis de montage et chevilles
Étape 2 : Monter la caméraRemarque : Cette caméra de sécurité
peut être montée contre un mur ou au plafond. Les instructions
d’installation qui suivent sont prévues pour le montage au plafond,
mais elles peuvent également être adaptées pour le montage
mural.
4. Acheminer les câbles de la caméra à travers le trou du câble
ou à travers la sortie latérale de la base de la caméra.
5. Fixer la caméra au plafond ou au mur avec les vis fournies
(et avec les chevilles, pour la brique ou le stuc).
Pour le réglage panoramique : desserrer la base circulaire et
régler jusqu’à 360°. Resserrer la base circulaire une fois la
caméra positionnée comme souhaité.
Pour le réglage de l’inclinaison du bras : desserrer la vis du
bras et incliner le bras jusqu’à 180°. Resserrer la vis une fois le
bras positionné comme souhaité.
Pour le réglage de la rotation de la caméra : desserrer la vis
de la caméra et tourner la caméra jusqu’à 360°. Resserrer la vis
une fois la caméra positionnée comme souhaité.
Vérifier que la base circulaire et les vis de réglage de chaque
caméra sont bien serrées avant de poursuivre.
Vis de caméra (rotation)
Vis du bras (inclinaison)
Base circulaire (panoramique)
1. Appliquer le gabarit de montage autocollant sur le plafond à
l’emplacement désiré pour la caméra.
2. Marquer l’emplacement des trous de montage.
3. Percer les trous pour les vis (indiqués 1 sur le gabarit) et
le trou de passage du câble (si désiré, indiqué A) aux emplacements
indiqués.
Utiliser les tailles de forets de perçage suivantes :brique ou
stuc = 5,5 mm (7/32 po) surface en bois = 1,6 mm (1/16 po)
Sortie latérale
Régler la position de la caméra pour obtenir l’angle
souhaité.
Étape 3 : Orienter la caméra
Étape 4 : Connecter la caméra au DVR1. Repérer les câbles
provenant de la caméra.
Faire correspondre les câbles vidéo et d’alimentation à une
extrémité d’un câble BNC et les connecter.
12
34
56
78
VIDEO IND+ D-RS-485
VGA IN
OUTAUDIO LAN&USB 12V
Caméra BNC
2. Brancher le câble de sortie vidéo à l’autre extrémité de ce
câble BNC sur l’une des prises VIDEO IN (Entrée vidéo) à l’arrière
du DVR.
3. Brancher le câble d’entrée d’alimentation à l’autre extrémité
de ce câble BNC dans l’adaptateur d’alimentation de la caméra.
4. Connecter l’adaptateur d’alimentation sur l’adaptateur
d’alimentation de la caméra.
Panneau arrière du DVR
(1) Câble BNC de 18,3 m (60 pi)
(1) Adaptateur d’alimentation
de caméra
Adaptateur d’alimentation
de caméra
HSCAM2 QSG 01
© 2018 Voxx Accessories Corp. 3502 Woodview Trace, Suite 220
Indianapolis, IN 46268
www.RCAAudioVideo.com