ISSUED: 1-5-04 SHEET #: 055-9196-1 Visit the InFocus Web Site at www.infocus.com 1 of 7 Read instruction sheet before you start i nstallation and assembly. Maximum Load Capacity: 50 lb (27 kg) Installer must verify that the ceiling will safely support the combined weight of projector mount and projector. WARNING IMPORTANT! Be sure not to touch the projector while tightening the set screw on the ball and socket mount. This may cause the image to be unaligned when you let go. Installation and Assembly - All-in-one Projector Adapter Plate for InFocus ®Projectors Models: SP-CEIL-011 R Installations: Flush Mount ......................................................................................................................................... step 1, page 3 Wood Joist Finished Ceilings, Exposed Wood Jois ts, or Wood Beam Ceilings .............................................................................. step 2, page 3 Concre te Ceilings ............................................................................................................................................ page 4 Exten sionColumns ......................................................................................................................................... page 5 IMPORTANT! T urn to the appropriate page for your ceiling installation. SET SCREW This product is intended for use with UL Listed products and must be installed by a qualified professional installer.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Read instruction sheet before you start installation and assembly.
Maximum Load Capacity: 50 lb (27 kg)
Installer must verify that the ceiling will safely supportthe combined weight of projector mount and projector.WARNING
IMPORTANT! Be sure not to touch the projector while tightening the set screw on theball and socket mount. This may cause the image to be unaligned when you let go.
Installation and Assembly - All-in-one Projector Adapter Plate for
InFocus ® ProjectorsModels: SP-CEIL-011
R
Installations:
Flush Mount ......................................................................................................................................... step 1, page 3
CEILINGDrill two 5/32" (4 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach ceiling plate (G)with two #14 x 2.5" (6 mm x 65 mm) wood
screws (F) as shown using 3/8" (10 mm) socketwrench. Tighten wood screws (F) so ceiling
plate (G) is firmly attached.
DO NOT TIGHTEN WITH EXCESSIVE FORCE!Over-tightening can cause stress damage to
wood screws (F) greatly reducing their holdingpower! Tighten to 80 in • lb (9 N.M.) maximum
torque.
Skip to step 5.
WARNING: It is the responsibility of the
installer to verify that the ceiling will safelysupport the combined load of all attached
hardware and components.IMPORTANT: Be sure to drill holes into thejoist CENTER!
For Optional Cord Management,install two spacers (H) between ceiling
plate (G) and ceiling.
Screw ball and socket mount (A) into ceiling plate (G). Align the notch with one of the four holes of the ceiling plate(G) and secure ball and socket mount (A) with a M5 x 10 mm socket pin screw (C) using security allenwrench (B) as shown in detail 1.Note: Slotted set screw (K) is used to jam against the threads of the ball andsocket mount to prevent any excess movement of the ball and socketmount (A). Do not over-tighten screw; over-tightening screw will damagethreads making it difficult to separate the products.
CAUTION: Tighten wood screws so ceiling plate(G) is firmly attached. DO NOT TIGHTEN WITH
EXCESSIVE FORCE! Over-tightening can causestress damage to wood screws, greatly reducing
their holding power! Tighten to 80 in • lb (9 N.M.)
maximum torque.
Drill two 1/4" (6 mm) dia. holes to a minimum depth of2.5" (64 mm). Attach ceiling plate (G) using two
concrete anchors and #14 x 2.5" wood screws (F) asshown in Illustration A and 1, 2, and 3 (below).
Tighten all fasteners.
Skip to step 5.
IMPORTANT: It is the responsibility of the installerto verify that the ceiling will safely support the
combined load of all attached hardware andcomponents.
1
3
Drill hole and insert anchor
Place ceiling plate over anchor and secure with screw
After repeating step one tighten all fasteners C U T A W
A Y V I E W
INCORRECT
concretemetalbracket
plaster/ dry wall
CORRECT
concretemetalbracket
plaster/ dry wall
FOR DIRECT ATTACHMENT TO LOAD BEARING CONCRETE
ONLY! Concrete expansion anchors are not intended forattachment to concrete ceilings covered with a layer of plaster,drywall, or other finishing material. If mounting to concrete
ceiling covered with plaster / drywall is unavoidable, plaster / drywall must be counterbored as shown below.
concreteceiling
concreteanchor
concreteanchor
concrete
anchor
F
F
F
Illustration A
Installation to Concrete CeilingsAlligator ® concrete anchors are recommended
Screw extension column to ceiling plate (G).Align the notch with one of the four holes in
the ceiling plate (G) and secure extensioncolumn with a M5 x 10 mm socket pinscrew (C) using security allen wrench (B).
See detail 3.
Screw extension column connector (I) to
extension column. Align slot in extensioncolumn with one of the top holes in
extension column connector (I). Insert andtighten one 10-32 x 3/8 socket pin screw (J)through extension column connector (I) into
slot on extension column using securityallen wrench (B). See detail 4.
Screw ball and socket mount (A) toextension column connector (I). Align slot in
ball and socket mount (A) to one of the
bottom holes in extension column connector(I). Insert and tighten one 10-32 x 3/8 socketpin screw (J) through extension columnconnector into slot in ball and socket mount
(A) using security allen wrench (B).
Note: Slotted set screw (K) is used to jamagainst the threads of the ball and socketmount to prevent any excess movement ofthe ball and socket mount (A). Do not over-tighten screw; over- tightening screw willdamage threads making it difficult toseparate the products.
Flip projector upside down. Find your projector from the models listed below. Using the holes indicated on thecorresponding hole pattern diagram, attach adapter plate (L) to projector using three M4 x 16 mm serrated washer
head socket pin screws (M) and three .198 x .313 x .375 retaining spacers (O).Notes:
Retaining spacers go between adapter plate and projector.* Notch indicates front of projector.** Projectors using hole pattern G use one M4 x 12 mm screw (N) and one .198 x .313 x .187 retaining spacer (P)
where indicated.
A. C200, C420, DP6500X, DP8200X,LP650, LP820, SP7200, SP7205
Peerless is a registered trademark and Armor Lock is a trademark of Peerless Industries Inc.All other brand and product names are trademarks or registered trademarks of their respective owners.
SET SCREW
Attach projector to the ball and socket mount (A) by
inserting the ball and socket mount (A) into the
adapter plate connection and twisting until the adapter
plate will no longer turn (about 75°). The spring loaded
captive screw should line up with a correspondinghole on the adapter plate (this should line up auto-
matically when the two are connected). Push down
and tighten the spring loaded captive screw to secure
the adapter plate to the mount. If not using the optional
security feature, fasten thumb screw (D) in the hole
opposite the spring loaded captive screw.
OPTIONAL: For Armor Lock™ security, insert serrated
washer head socket pin security screw (E) in the hole
opposite the spring loaded captive screw. Tighten with
security allen wrench (B). This will prevent the
projector from being removed.
Note: Be sure to only use the 10-32 x 3/8" screw (E)(or the thumb screw (D)) opposite the spring loaded