MANUFACTURING PROCESS OF SOLAR PANEL
MANUFACTURING PROCESS OF
SOLAR PANEL
MANUFACTURING PROCESS OF SOLAR PANEL
CELL TESTER MACHINE
FUNCTION TO CHECK THE SOLAR CELL PARAMETERS SUCH AS –• MAXIMUM CELL POWER, Pm (WATT)• OPEN CIRCUIT VOLTAGE, Voc (VOLTS)• SHORT CIRCUIT CURRENT Isc (AMPERE)• MAXIMUM POWER CURRENT, Ipm (AMPERE)• MAXIMUM POWER VOLTAGE, Vpm• SERIESE RESISTANCE OF SOLAR CELLS, Rs (OHM)• PARALLEL RESISTANCE OF SOLAR CELLS, Rsh (OHM)• SOLAR CELL EFFICIENCY ( %)• FILL FACTOR (%)• LIGHT INTENSITY • TEMPRATURE.
FIBER LASER SCRIBINGLaser Scribing Machine.• Forced Air Cooling. •NO water required. •Very High Speed. •No Spares like Diode, Lamp required.•Higher transfer efficiency, •lower running cost (2KVA)•Module and compact structure, smallest size.•Narrow cutting kerfs (30μm) and more smooth edge.
FUNCTION• Scribing or cutting the Solar Cells and Silicon
Wafers in solar PV, including the (mono crystalline silicon) and poly- si (poly crystalline silicon)solar cells and silicon wafer.
• According to our need we can cut the solar cells.
RIBBON CUTTING MACHINE
This machine is used for cutting of ribbons as required for solar cells.
AUTOMATIC SOLAR CELL STRINGER MACHINE
FUNCTION• Automatic Tabbed Stringer for CUT CELL & FULL
CELL (any size from 30mm to 156mm).• Suitable for 5”,6” square cell and rectangle cut
cells.• Possibility to change from 2, 3, 4 Bus Bar cell • Adjustable cell holder (no need of kits). • Fully Automatic string unloading on tray. • Breakage rate::≤0.3, for cut cells rate::≤.5%• Special design IR Lamp.
FILM CUTTING TABLE
This table is used for cutting EVA and back sheet for solar panel.The EVA and PV back sheet is designed to protect the inner components of the module, specifically the photovoltaic cells and electrical components from external stresses as well as act as an electric insulator.
GLASS WASHER MACHINE
•This machine is used for washing glass of solar panel.•It cleans the glass and after cleaning make it dry.
LAYUP STATION
This machine is used for assembling of cell string , EVA, back sheet /PET on glass and after that giving connection of panel.Also used for checking short circuit current and open circuit voltage.
PROCESS OF ASSEMBLING
EL TESTER MACHINE
FUNCTION • This machine is used for defect detection of
panel.• It detect the faults like braking or cracking of
solar cells.
SOLAR PANEL MODULE LAMINATOR
FUNCTION In the manufacturing of photovoltaic modules,
the laminator machine is of fundamental importance in curing the EVA, to join the layers that form the module and remove all air from between them. When the materials in the photovoltaic module have been placed on the glass, they undergo a heat treatment that converts the EVA into a type of gel that encapsulates all the layers to form a very strong and compact sandwich.
AFTER LAMINATION SOLAR PANEL
AUTO CORNER CUTTING SAW
FUNCTIONThis machine is used for aluminum corner connector profile cutting into right angle pieces.
ALUMINIUM MULTI PROFILE CUTTING OFF SAW MACHINE
FUNCTIONThis machine is designed for cutting 45 degree V-shaped grooved of aluminum profile.
FOUR HEAD PNEUMATIC PUNCHING MACHINE
FUNCTIONThis machine is used for aluminum profile punching holes.
DOUBLE HEAD CUTTING SAW
FUNCTIONThis machine is designed for cutting Aluminum profile at the angle of ± and
GLUE GUN AND SEALANT
FUNCTION• Sealant act as a moisture barrier and
provide insulating coating.• Provide mechanical strength to solar
panel.• Also used for sticking the junction box on
panel.
FRAMING MACHINE
FUNCTIONAautomatic Solar Module Framing Machine is used to assemble solar module automatically.
SUN SIMULATOR MACHINE
FUNCTIONThis machine is used for testing the technical parameters and shows the relation between voltage, current and power of solar panel after assembling.
Panel checking glass
NEW ADDITION TO THE ARMOUR
Used for string making for 3 watt to 20 watt panel
THANK YOU