This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-1
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-2
PRODUCT SPECIFICATIONS
EXTERIOR FINISH
Exterior aluminum surfaces are low maintenance extruded aluminumcoated with a thermo set polyester finish that meets or exceeds theAAMA 2603 performance standards. Standard colors include BrilliantWhite, Chestnut Bronze, Desert Sand, French Vanilla, Hartford Green,Mesa Red, Black, Arctic Silver and Dark Chocolate.
AURALASTR WOOD
AuraLastR wood is fundamentally different from wood resultingfrom traditional millwork preservation processes in that it uses aproprietary vacuum/pressure process to provide protectionthroughout the wood parts used to make windows and doors.AuraLastR wood is distinguished from wood using the currentpreservation methods by its unique ability to achieve greaterpenetration of the active ingredients into the wood parts, with apenetration of the treatment being a minimum of 92%.
INTERIOR FINISH
All interior surfaces are unfinished clear pine ready for on sitefinishing. Primed and pre-finished interiors are available in paint:Pure White, Extra White, Natural Choice, Moderate White; in stain:Wheat, Cherry, Cordovan; and Clear Lacquer.
FRAME
Frame is assembled from select kiln dried pine using AuraLastRwoodon all exterior parts. Exterior surface is covered with .050 (1.27mm)extruded aluminum cladding; corner joints are mechanically fastenedover a silicone injected nylon corner key. Frame thickness is 1-5/32”(29.4mm) at head, side jamb and at sill. Basic jamb width is 2-1/2”(63.5mm). Standard jamb width is 4-9/16” (116mm). Integral nailingfin is part of extrusion on all four sides. Assembled frame includes allweather-stripping and hardware installed. Exterior of frameextrusion is grooved to accept accessories.
SASH
Sash is 1-7/16” (36.5mm) thick and combines an extruded aluminumexterior with select kiln-dried pine using AuraLastR wood. Joints aremortise and tenoned, machine clamped for squareness and securedwith metal fasteners. Exterior surfaces are covered with .045 (1.2mm)extruded aluminum.
GLAZING
3/4” (19mm) thick sealed insulating glass is constructed from twopanes of glass, utilizing a continuous roll formed stainless steel spacerwith dual seal sealant. The glass is mounted into the sash using asilicone-glazing compound and secured with interior applied profiledwood stops. All insulating glass units comply with the performancerequirements of IGCC in accordance with either ASTM E774 or E2190.
GLAZING OPTIONS
3/4” insulating glass available in Low-E with Argon, Low-E, Low-E 366,Clear, Neat Glass, reflective, tinted, or obscure, tempered or otherspecialty glass as specified. Preserve® film is a 0.003” thickpolyethylene film with a low tack acrylic adhesive applied to the glassfor protection during shipping and installation. 4,000 foot elevationsand higher require a capillary tube to equalize environmental stress(otherwise known as High Altitude glazing). High Altitude glazingdoes not allow the use of Argon as listed under glazing options.
WEATHER-STRIPPING
Engineered system combines a flexible, lined weather-strip applied tothe full perimeter of the sash and thermoplastic rubber bulb appliedto the full perimeter of the frame.
HARDWARE
Sash pivot on concealed hinges with sliding steel reinforced nylonshoes in an integral frame track. Stainless steel concealed lockingsystem is standard, and the window locks sequentially. EntryGarddual arm retro operator has removable polycarbonate cover, die castzinc bash and hardened steel worm gears and arms. Hinges and retrooperator arms feature stainless steel. The die cast locking lever islocated on the side jamb at the lower corner of the window oppositethe operator and has a molded bezel cover that snaps over the routon the side stop. Units under 20” wide will feature a dyad operator.Color choices for locks and operator covers are White, ChestnutBronze, Desert Sand or optional Bright Brass, Antique Brass, PolishedBrass, Brushed Chrome or Imitation Oil Rubbed Bronze.
INSECT SCREENS
Charcoal fiberglass screen cloth (18x16 mesh) set in painted rollformed aluminum frame fitted to the inside of the window with allnecessary hardware, in White, Chestnut Bronze, Desert Sand oroptional Bright Brass, Antique Brass, Polished Brass, Brushed Chromeor Imitation Oil Rubbed Bronze. Aluminum mesh and Phantomscreens are also available. Insect screens are intended to allow air andlight in and to keep insects out. They are not intended to keep anyoneor anything from falling through an open window. For safety screensor other security devices contact your local building supply retailer.
GRILLES
SDL (Simulated Divided Lites) - extruded aluminum muntinspermanently applied to the exterior of the insulating glass unit (notavailable on textured glass) in 7/8” (22mm), 1-1/8”(28.5mm), or 1-3/8”(34.9mm) widths. SDL is standard with a light bronze internal shadowbar to give a true divided lite appearance. As an option, SDL may beordered with a silver shadow bar. Clear wood interior muntin barsmatch the exterior muntin width and are permanently bonded to theinterior of the glass. Also available is a 2-5/16” (59mm) SDL bar, whichsimulates a double-hung checkrail.
Full Surround Wood Grilles - Rectangular unfinished clear pinewood grilles in 7/8” (22mm) are available in patterns selected by theowner.
GBG (Grilles between the Glass) - 5/8” (15.9mm) flat and 23/32” or 1”contour mounted between the glass panes suspended within the aircavity.
EXTERIOR TRIM
1-5/8” (41mm) wide aluminum brickmould or Adams casing with anintegral nailing fin is available factory applied. Also available is 3-1/2”(88.5mm) flat casing with an integral nailing fin. All of the accessoriesare .050” (1.3mm) extruded aluminum. Two sizes of frame expander,1-7/8” (48mm) and 3-1/4“ (83mm) may be used alone or in conjunctionwith a 2-1/8” (54mm) mull expander. Standard 5/16” (8mm) clad mullcover used for joining windows together. Windows may also be joinedwith 1” (25.4mm), 2” (51mm), or 4” (102mm) mull covers. Color andfinish match exterior finish specs above.
Continued on next page
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-3
PRODUCT SPECIFICATIONS
EXTENSION JAMBS
Extension jambs are factory applied to the interior on all four sides ofthe frame and are 4/4 standard thick pine to accommodate walldepths up to 7-1/4” with one piece, and up to 12” with two pieces.9/16” (14.2mm) and 5/4 option or 5/4-4/4 stacked option also available.
INSTALLATION
Installation per JELD-WEN Installation Method for Metal CladWindows JII002 or JII013. See www.jeld-wen.com/resources forinstructions.
PERFORMANCE
NFRC Certified - (Rated and labeled in accordance with NFRC)
WDMA Hallmark Certified -In accordance with AAMA/NWWDA/101/I.S.2-97
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-4
QUICK SPEC GUIDE
SPECIFICATION STANDARD FEATURESOPTIONAL FEATURES
Some options may require additional lead times.Consult your JELD-WEN Sales Representative.
EXTERIOR FINISH S Brilliant WhiteS Chestnut BronzeS Desert SandS French VanillaS Mesa Red
S Hartford GreenS BlackS Arctic SilverS Dark Chocolate
EXTERIOR TRIM S Nailing FinS Drip Cap
S Aluminum 1-5/8” Brickmould with integral nailingfin
S Adams or 3-1/2” Flat Casing with integral nailingfin
INTERIOR FINISH S Natural S Priming Available
Pre-finished Interior Options are:S Paint - Pure White, Extra White, Natural Choice,
S Operator, Stationary & Fixed Units:Any Height: 12” to 84”Operating Units: 14” to 84”
S 36” x 78”, and 28”, 30”, 36” x 84” not available asoperating
S For RO, add 3/4”
GLAZING S Low-E Insulating GlassS Preserve® Protective Film
S ClearS ObscureS BronzeS Low-E 366
S Neat GlassS ReflectiveS Tempered
S High Altitude
GRILLES S 5/8” Flat, 23/32” or 1” Contour GBGS 7/8” Full Surround Wood Grilles
SDL Bead Profile:S 7/8”, 1-1/8”, 1-3/8”, 2-5/16” with Light Bronze
Shadow BarS 7/8”, 1-1/8”, 1-3/8”, 2-5/16” with Silver Shadow Bar
HARDWARE S Standard Folding Nesting HandleS Concealed Locking System
S T-Handle S Round Knob
HARDWARE COLOR S WhiteS Desert SandS Chestnut Bronze
S Antique BrassS Polished BrassS Brushed Chrome
S Imitation OilRubbed Bronze
Continued on next page
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-5
QUICK SPEC GUIDE
SPECIFICATION STANDARD FEATURESOPTIONAL FEATURES
Some options may require additional lead times.Consult your JELD-WEN Sales Representative.
JAMB S 4-9/16” S Minimum: 2-1/2”S Maximum: 7-1/4” (one piece)S Maximum: 12” (two piece)
SCREENS S Fiberglass S Aluminum Mesh availableS Phantom Screen - some size limitations apply
SCREEN FRAME COLOR S Brilliant WhiteS Desert SandS Chestnut Bronze
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-6
DIMENSIONAL WINDOWSClad casement windows may be specified as ”dimensional”, by adjusting thedesired rough opening width or height in 1/4” increments from standard.
Clad casement windows are available with left or right hand operation, orstationary (non-venting). Operating mechanism includes corrosion resistant steelhinges and dual arm roto-type operator with hardened steel gears and operatingarms. Sash locks are concealed unison type with an exposed locking lever andescutcheon plate. There are several interior hardware finish options. Refer to theSpecifications for finish options.
MULTIPLE ASSEMBLIESClad casement windows may be mulled above, below, or beside other clad casementwindows, or other clad window products. Factory assembled mulls are limited in height (100”),width (150”), and a total area (75 square feet).
GENERAL INFORMATIONCASEMENT
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-7
CASEMENT UNIT HANDING:UNIT HANDING IS DEFINED (FROMTHE EXTERIOR) AS THEDIRECTION THE SASH OPENS.
LEFTHAND
RIGHTHAND
OPERATOR OPERATOR
HANDING & OPERATIONCASEMENT
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-8
GENERAL CASEMENT NOTES
ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDEDTO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THESTRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS.
BOOK CODE
ECC1818
OUTSIDE OF FRAME
M.O. Adams/Flat CasingRough Opening
M.O. Brickmould
Frame SizeDaylight Opening
Masonry Openings for Brickmould, Flat & Adams Casing.Vertical measurements include sillnose.(Subtract 1/2” from Masonry Opening for Unit Size)
M.O. MASONRY OPENING1. SITELINE EX CLAD CASEMENT (ECC) UNITS ARE AVAILABLE ASOPERATING OR STATIONARY UNITS.
2. ’ECCP’ IN A BOOK CODE DENOTES THE UNIT IS A CLAD CASEMENTPICTURE (STATIONARY) UNIT.
3. UNIT ELEVATIONS ARE SHOWN WITHOUT EXTERIOR TRIM. UNITSIZES & MASONRY OPENING DIMENSIONS WILL CHANGE WITHTHE ADDITION OF EXTERIOR TRIM. SEE THE ’UNIT SIZING, ROUGHOPENINGS & MASONRY OPENINGS’ PAGE FOR EXTERIOR TRIMEFFECTS.
4. OPERATING UNITS ARE AVAILABLE AS LEFT OR RIGHT HANDOPERATION.
5. DIMENSIONAL VALUES IN PARENTHESES ARE MILLIMETERCONVERSIONS.
THE FIRST TWO NUMBERSINDICATE THE UNIT WIDTH
THE LAST TWO NUMBERS INDICATETHE UNIT HEIGHT
’ECC’ INDICATESSITELINE EX CLAD CASEMENT
ELEVATION NOTESCASEMENT
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-9
SCALE 1/4” = 1’
1-WIDE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
S AVAILABLE AS STATIONARY ONLY.E BASIC UNIT CLEAR OPENING EXCEEDS 20” IN WIDTH, 24” IN HEIGHT & A MINIMUM OF 5.7 SQ. FT.
E
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-10
SCALE 1/4” = 1’
1-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
S AVAILABLE AS STATIONARY ONLY.E BASIC UNIT CLEAR OPENING EXCEEDS 20” IN WIDTH, 24” IN HEIGHT & A MINIMUM OF 5.7 SQ. FT.
E
E
E
E
E
E
E
E
E
E
E
E
E
E
S
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-11
SCALE 1/4” = 1’
1-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
S AVAILABLE AS STATIONARY ONLY.
S S S
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-12
SCALE 1/8” = 1’
2-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-13
SCALE 1/8” = 1’
2-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-14
SCALE 1/8” = 1’
3-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-15
SCALE 1/8” = 1’
3-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose,see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-16
SCALE 1/8” = 1’
4-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-17
SCALE 1/8” = 1’
4-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-18
SCALE 1/8” = 1’
4-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see TrimOptions page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-19
SCALE 1/8” = 1’
5-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-20
SCALE 1/8” = 1’
5-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-21
SCALE 1/8” = 1’
5-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for UnitSizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. Forother Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-22
SCALE 1/8” = 1’
5-WIDE UNITS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for UnitSizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. Forother Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-23
SCALE 1/4” = 1’
PICTURE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-24
SCALE 1/4” = 1’
PICTURE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-25
SCALE 1/4” = 1’
PICTURE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-26
SCALE 1/4” = 1’
PICTURE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
66”(1676)66 3/4”(1695)72 1/2”(1842)69 1/2”(1765)
72”(1829)72 3/4”(1848)78 1/2”(1994)75 1/2”(1918)
ECCP6612 ECCP7212
ECCP6618 ECCP7218
ECCP6620 ECCP7220
ECCP6624 ECCP7224
ECCP6630 ECCP7230
ECCP6636 ECCP7236
ECCP6642 ECCP7242
ECCP6648 ECCP7248
60 3/32”(1526) 66 3/32”(1679)
ECCP6628 ECCP7228
63/
32”(
155)
12”(
305)
123/
4”(3
24)
1513
/16”
(402
)14
5/16
”(36
4)
18”(
457)
183/
4”(4
76)
20”(
508)
203/
4”(5
27)
24”(
610)
243/
4”(6
29)
30”(
762)
303/
4”(7
81)
36”(
914)
363/
4”(9
33)
42”(
1067
)42
3/4”
(108
6)48
”(12
19)
483/
4”(1
238)
28”(
711)
283/
4”(7
30)
123/
32”(
307)
2113
/16”
(554
)
143/
32”(
358)
2313
/16”
(605
)
183/
32”(
460)
2713
/16”
(706
)
223/
32”(
561)
3113
/16”
(808
)
243/
32”(
612)
3313
/16”
(859
)
303/
32”(
764)
3913
/16”
(101
1)
363/
32”(
917)
4513
/16”
(116
4)
423/
32”(
1070
)
5113
/16”
(131
6)20
5/16
”(51
5)22
5/16
”(57
8)26
5/16
”(66
8)30
5/16
”(77
0)32
5/16
”(82
1)38
5/16
”(97
3)44
5/16
”(11
26)
505/
16”(
1278
)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-27
SCALE 1/4” = 1’
PICTURE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
ECCP6654 ECCP7254
ECCP6660 ECCP7260
ECCP6666 ECCP7266
ECCP6672 ECCP7272
ECCP6678 ECCP7278
66”(1676)66 3/4”(1695)72 1/2”(1842)69 1/2”(1765)
72”(1829)72 3/4”(1848)78 1/2”(1994)75 1/2”(1918)
60 3/32”(1526) 66 3/32”(1679)
54”(
1372
)54
3/4”
(139
1)60
”(15
24)
603/
4”(1
543)
66”(
1676
)66
3/4”
(169
5)72
”(18
29)
723/
4”(1
848)
78”(
1981
)78
3/4”
(200
0)
483/
32”(
1222
)
5713
/16”
(146
8)
543/
32”(
1374
)
6313
/16”
(162
1)
603/
32”(
1526
)
6913
/16”
(177
3)
663/
32”(
1679
)
7513
/16”
(192
6)
723/
32”(
1831
)
8113
/16”
(207
8)56
5/16
”(14
30)
625/
16”(
1583
)68
5/16
”(17
35)
745/
16”(
1888
)80
5/16
”(20
40)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-28
SCALE 1/4” = 1’
PICTURE UNITS
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
ECCP6684 ECCP7284
66”(1676)66 3/4”(1695)72 1/2”(1842)69 1/2”(1765)
72”(1829)72 3/4”(1848)78 1/2”(1994)75 1/2”(1918)
60 3/32”(1526) 66 3/32”(1679)
84”(
2134
)84
3/4”
(215
3)
783/
32”(
1984
)
8713
/16”
(223
0)86
5/16
”(21
92)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-29
SCALE 1/8” = 1’
PICTURE UNITS WITH 18” FLANKERS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
12 3/32”(307)[2] 36 3/32”(917)78”(1981)
78 3/4”(2000)84 1/2”(2146)81 1/2”(2070)
ECCPF4242-18 ECCPF5442-18 ECCPF6642-18
ECCPF4248-18 ECCPF5448-18 ECCPF6648-18
ECCPF4254-18 ECCPF5454-18 ECCPF6654-18
ECCPF4260-18 ECCPF5460-18 ECCPF6660-18
ECCPF4266-18 ECCPF5466-18 ECCPF6666-18
12 3/32”(307)[2] 48 3/32”(1222)90”(2286)
90 3/4”(2305)96 1/2”(2451)93 1/2”(2380)
12 3/32”(307)[2] 60 3/32”(1526)102”(2591)
102 3/4”(2610)108 1/2”(2756)105 1/2”(2680)
363/
32”(
917)
42”(
1067
)42
3/4”
(108
6)45
13/1
6”(1
164)
445/
16”(
1126
)
423/
32”(
1070
)48
”(12
19)
483/
4”(1
238)
5113
/16”
(131
6)50
5/16
”(12
78)
483/
32”(
1222
)54
”(13
72)
543/
4”(1
391)
5713
/16”
(146
8)56
5/16
”(14
30)
543/
32”(
1374
)60
”(15
24)
603/
4”(1
543)
6313
/16”
(162
1)62
5/16
”(15
83)
603/
32”(
1526
)66
”(16
76)
663/
4”(1
695)
6913
/16”
(177
3)68
5/16
”(17
35)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-30
SCALE 1/8” = 1’
PICTURE UNITS WITH 20” FLANKERS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
14 3/32”(358)[2] 36 3/32”(917)82”(2083)
82 3/4”(2102)88 1/2”(2248)85 1/2”(2172)
ECCPF4242-20 ECCPF6642-20
ECCPF4248-20
ECCPF4254-20
ECCPF4260-20
ECCPF4266-20
ECCPF5442-20
ECCPF6648-20ECCPF5448-20
ECCPF6654-20ECCPF5454-20
ECCPF6660-20ECCPF5460-20
ECCPF6666-20ECCPF5466-20
14 3/32”(358)[2] 48 3/32”(1222)94”(2388)
94 3/4”(2407)100 1/2”(2553)97 1/2”(2477)
14 3/32”(358)[2] 60 3/32”(1526)106”(2692)
106 3/4”(2711)112 1/2”(2858)109 1/2”(2781)
363/
32”(
917)
42”(
1067
)42
3/4”
(108
6)45
13/1
6”(1
164)
445/
16”(
1126
)
423/
32”(
1070
)48
”(12
19)
483/
4”(1
238)
5113
/16”
(131
6)50
5/16
”(12
78)
483/
32”(
1222
)54
”(13
72)
543/
4”(1
391)
5713
/16”
(146
8)56
5/16
”(14
30)
543/
32”(
1374
)60
”(15
24)
603/
4”(1
543)
6313
/16”
(162
1)62
5/16
”(15
83)
603/
32”(
1526
)66
”(16
76)
663/
4”(1
695)
6913
/16”
(177
3)68
5/16
”(17
35)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-31
SCALE 1/8” = 1’
PICTURE UNITS WITH 24” FLANKERS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
18 3/32”(460)[2] 36 3/32”(917)90”(2286)
90 3/4”(2305)96 1/2”(2451)93 1/2”(2380)
ECCPF4242-24 ECCPF5442-24 ECCPF6642-24
ECCPF4248-24 ECCPF5448-24 ECCPF6648-24
ECCPF4254-24 ECCPF5454-24 ECCPF6654-24
ECCPF4260-24 ECCPF5460-24 ECCPF6660-24
ECCPF4266-24 ECCPF5466-24 ECCPF6666-24
18 3/32”(460)[2] 48 3/32”(1222)102”(2591)
102 3/4”(2610)108 1/2”(2756)105 1/2”(2680)
18 3/32”(460)[2] 60 3/32”(1526)114”(2896)
114 3/4”(2915)120 1/2”(3061)117 1/2”(2985)
363/
32”(
917)
42”(
1067
)42
3/4”
(108
6)45
13/1
6”(1
164)
445/
16”(
1126
)
423/
32”(
1070
)48
”(12
19)
483/
4”(1
238)
5113
/16”
(131
6)50
5/16
”(12
78)
483/
32”(
1222
)54
”(13
72)
543/
4”(1
391)
5713
/16”
(146
8)56
5/16
”(14
30)
543/
32”(
1374
)60
”(15
24)
603/
4”(1
543)
6313
/16”
(162
1)62
5/16
”(15
83)
603/
32”(
1526
)66
”(16
76)
663/
4”(1
695)
6913
/16”
(177
3)68
5/16
”(17
35)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-32
SCALE 1/8” = 1’
PICTURE UNITS WITH 28” FLANKERS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
22 3/32”(561)[2] 36 3/32”(1222)98”(2489)
98 3/4”(2508)104 1/2”(2654)101 1/2”(2578)
ECCPF4242-28 ECCPF5442-28
ECCPF4248-28 ECCPF5448-28
ECCPF4254-28 ECCPF5454-28
ECCPF4260-28 ECCPF5460-28
ECCPF4266-28 ECCPF5466-28
22 3/32”(561)[2] 48 3/32”(1222)110”(2794)
110 3/4”(2813)116 1/2”(2959)113 1/2”(2883)
363/
32”(
917)
42”(
1067
)42
3/4”
(108
6)45
13/1
6”(1
164)
445/
16”(
1126
)
423/
32”(
1070
)48
”(12
19)
483/
4”(1
238)
5113
/16”
(131
6)50
5/16
”(12
78)
483/
32”(
1222
)54
”(13
72)
543/
4”(1
391)
5713
/16”
(146
8)56
5/16
”(14
30)
543/
32”(
1374
)60
”(15
24)
603/
4”(1
543)
6313
/16”
(162
1)62
5/16
”(15
83)
603/
32”(
1526
)66
”(16
76)
663/
4”(1
695)
6913
/16”
(177
3)68
5/16
”(17
35)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-33
SCALE 1/8” = 1’
PICTURE UNITS WITH 30” FLANKERS
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
24 3/32”(612)[2] 36 3/32”(917)102”(2591)
102 3/4”(2610)108 1/2”(2756)105 1/2”(2680)
ECCPF4242-30 ECCPF5442-30
ECCPF4248-30 ECCPF5448-30
ECCPF4254-30 ECCPF5454-30
ECCPF4260-30 ECCPF5460-30
ECCPF4266-30 ECCPF5466-30
24 3/32”(612)[2] 48 3/32”(1222)114”(2896)
114 3/4”(2915)120 1/2”(3061)117 1/2”(2985)
363/
32”(
917)
42”(
1067
)42
3/4”
(108
6)45
13/1
6”(1
164)
445/
16”(
1126
)
423/
32”(
1070
)48
”(12
19)
483/
4”(1
238)
5113
/16”
(131
6)50
5/16
”(12
78)
483/
32”(
1222
)54
”(13
72)
543/
4”(1
391)
5713
/16”
(146
8)56
5/16
”(14
30)
543/
32”(
1374
)60
”(15
24)
603/
4”(1
543)
6313
/16”
(162
1)62
5/16
”(15
83)
603/
32”(
1526
)66
”(16
76)
663/
4”(1
695)
6913
/16”
(177
3)68
5/16
”(17
35)
DAYLIGHT OPENINGFRAME SIZE
ROUGH OPENINGM.O. ADAMS/FLAT CASING
M.O. BRICKMOULD
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-34
Sector Top casements are constructed the same as Siteline EX casements(extruded cladding on wood sash).
Sector Top clad casement windows are available with left or right hand operation(hinged on the springline), or stationary (non-venting). Operating mechanisimincludes stainless steel, corrosion resistant, butt hinges and single arm roto-typeoperator with hardened steel gears and operating arm. Sash locks are concealedunison type with exposed locking lever and escutcheon plate. There are severalinterior hardware finish options. Refer to Specifications for finish options.
CLAD SECTOR TOP CASEMENTS utilize some of the same options asCLAD CASEMENT.
GENERAL INFORMATIONSECTOR TOP CASEMENT
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-35
CASEMENT UNIT HANDING:UNIT HANDING IS DEFINED (FROMTHE EXTERIOR) AS THEDIRECTION THE SASH OPENS.
HANDLEFT
HANDRIGHT
UNIT HANDING INFORMATION
S OPERATING SINGLE SECTOR UNITS - MAY BE HANDED ’LEFT’ OR ’RIGHT’.
S OPERATING TWIN SECTOR UNITS - THESE UNITS ARE HINGED ON THE SPRINGLINE SIDE. THE ’LEFT’ SASH HAS ’LEFT’HAND OPERATION AND THE ’RIGHT’ SASH HAS ’RIGHT’ HAND OPERATION ONLY.
S OPERATING TRIPLE SECTOR UNITS - ONLY THE FLANKING UNITS MAY BE OPERATORS WHICH ARE HINGED ON THESPRINGLINE SIDE. THE TWO OPERATING SASH ARE HANDED THE SAME AS THE TWIN SECTOR.
OPERATOR OPERATOR
HANDING & OPERATIONSECTOR TOP CASEMENT
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-36
ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDEDTO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THESTRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS.
BOOK CODE
OUTSIDE OFFRAME
Masonry Openings for Brickmould, Flat & Adams Casing.Vertical measurements include subsill.(Subtract 1/2” from Masonry Opening for Unit Size)Daylight Opening
Frame Size
M.O. Brickmould
Rough OpeningM.O. Adams/Flat Casing
ECCS2442
1. UNIT ELEVATIONS ARE SHOWN WITHOUT EXTERIOR TRIM.
2. DIMENSIONAL VALUES IN BRACKETS ARE MILLIMETER CONVERSIONS.
3. ALL SECTOR UNITS ARE AVAILABLE AS OPERATING UNITS.
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-37
SCALE 1/4” = 1’
SECTOR TOP UNITS - 1-WIDE
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-38
SCALE 1/4” = 1’
SECTOR TOP UNITS - 1-WIDE
ELEVATION SYMBOL LEGEND:
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-39
SCALE 1/8” = 1’
SECTOR TOP UNITS - 2-WIDE
Note: Elevations shown DO NOT have exterior trim. Subtract 1/2” (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include SillNose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page.
VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT
ELEVATION SYMBOL LEGEND:
VALUES IN () ARE IN MILLIMETER CONVERSIONSM.O. = MASONRY OPENING
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-40
SASH GLAZING OPTIONS
SCALE 3” = 1’
INTERIOR GLAZING OPTIONS
5/DS//5/DS
1/4//1/4
7.3L//DS 3/16//3/16
DS//7.3L
PICTUREWINDOWS
ONLY
PICTUREWINDOWS
ONLY
PICTUREWINDOWS
ONLY
PICTUREWINDOWS
ONLY
7.0L//5/DS
CASEMENTPICTURE
5/DS//7.0L
CASEMENTPICTURE
CASEMENTPICTURE
15/16”3/16”3/16”
13/16”1/8” 1/8”
15/16”
1/4”1/4”
15/16”
1/8” 1/8”5/16”
13/16”
1/8” 1/8”1/4”
15/16”
1/8”5/16”1/8”
13/16”
1/8”1/4”1/8”
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-41
EXTERIOR TRIM
1 17/32” [39]
1 1/2” [38]
4 9/16” [116]
1 3/4” [44]
3” [76]
4 9/16” [116]
1 5/16” [33]
3” [76]
4 9/16” [116]
FLAT CASING3 1/2”
CASINGADAMSBRICKMOULDSTANDARD
1 1/4” [32]
1 3/8” [35]
4 9/16” [116]
SILL NOSE OPTIONS
STANDARD SILL NOSE
1 3/16” [30]
BOW AND BAY SILL NOSE
1 23/32” [44]
17/32” [13]
5/16” [8]
TRIM OPTIONSCASEMENT
SCALE: 3” = 1’
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-42
EXTERIOR TRIM
1 1/2” [38]
1 1/2” [38]
4 9/16” [116]
1 3/4” [44]
3” [76]
4 9/16” [116]
1 5/16” [33]
3” [76]
4 9/16” [116]
FLAT CASING3 1/2”
CASINGADAMSBRICKMOULDSTANDARD
1 1/4” [32]
1 3/8” [35]
4 9/16” [116]
SILL NOSE OPTIONS
STANDARD SILL NOSE
1 3/16” [30]
BOW AND BAY SILL NOSE
1 23/32” [44]
17/32” [13]
5/16” [8]
TRIM OPTIONSSECTOR TOP RADIUS
SCALE: 3” = 1’
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-43
JAMB EXTENDER OPTIONS
Notes:
Jamb Extension (9/16” thick) only available on jambs up to 6-9/16”.Jambs over 6-9/16” will only have a 4/4 or 5/4 option.Jambs over 7-1/4” up 12” will be 2 layers.Kerfed Jamb Extension only available on 4/4 or 5/4 options.
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-44
STANDARD MULLION OPTIONS
TWIN OPERATING CASEMENT OPERATING CASEMENT WITHFIXED UNIT
OPERATING CASEMENT WITHFIXED TRANSOM
RADIUS OVER CASEMENT
DIRECT-SET NEXT TO CASEMENT DIRECT-SET OVER CASEMENT
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-45
LITE CUT INFORMATION
LITE CUT OPTIONSSpecial lite cut patterns can include a wide
variety of straight line and radius patterns.The illustrations shown here represent just afew of the possibilities. Rectangular,horizontal, vertical and Prairie lite patternsare available in all standard size cladcasement windows. Uneven, diamond,
radius and Gothic lite cuts are available,subject to approval. Approvals are based on
the ability to fulfill the design requirementwhile maintaining the construction integrityof the finished product.
BAR ALIGNMENTAlignment of divided lite muntin bars from one window to thenext is often required by fine architectural design. Woodgrilles, GBG (Grilles between the Glass), and Simulated
Divided Lites may be specified with muntin bars aligned.
DIAMOND GOTHICRADIUS
RECTANGULAR HORIZONTAL UNEVENPRAIRIE
Clad casement windows are available in 7/8”, 1-1/8” and 1-3/8” widths for SDL (Simulated Divided Lites), 5/8”,23/32” and 1” GBG (Grilles between the Glass) and 7/8” removable grilles. Standard lite cuts are rectangular.
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-46
DIVIDED LITE OPTIONS
GRILLES MEETING
GRILLE PROFILES:
SCALE 3” = 1’
3/16” x 5/8” ALLMETAL 1021101018XX1403/16” x 1” ALLMETAL 1020101018XX1641/4” x 5/8” ALLMETAL 1020102018XX1401/4” x 1” ALLMETAL 1020102018XX1645.5mm x 18mm CONTOUR ALLMETAL 1020301010XX2558mm x 25mm CONTOUR ALLMETAL 1020301018XX380
NFRC 3mm RULE
7/8” SDL 1 1/8” SDL 1 3/8” SDL 2 5/16” SDL
5/8” GRILLE 23/32” GRILLE 1” GRILLE
7/8” SDL 1 1/8” SDL 1 3/8” SDL 2 5/16” SDL
5/8” GRILLE
23/32” GRILLE 1” GRILLE
1/4”
3/16” 3/16”3/16”
5/8”
5/8”
5/8”
3/16”
5/8”
3/4”
3/16”
11/16”
3/4” 3/4”
5/16”
1”
11/16”
3/16”
5/8”
11/16”
3/16”
9/16”
11/16”5/16”
1”
3/4”1/4”
3/4”1/4”
3/4”3/4”
11/16” 11/16” 11/16”11/16”
3/16”
1/4”
7/8”
5/16”
7/8”
5/16”
1 1/8”
5/16” 5/16”
1 1/8” 1 3/8”
5/16” 5/16”
1 3/8” 2 5/16” 2 5/16”
5/16”3/8”
7/8”
5/16”
7/8”
5/16”
1 1/8”
5/16” 5/16”
1 1/8” 1 3/8”
5/16” 5/16”
1 3/8” 2 5/16”
3/8”
2 5/16”
5/16”
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-47
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-65
BAY & BOW WINDOW ROUGH OPENINGS
Rough Opening typical for all UnitsRough Opening typical for all Units
OV
ERA
LLFR
AM
EH
EIG
HT
+1-
1/2”
OV
ERA
LLU
NIT
HEI
GH
T(B
ASI
CU
NIT
FRA
ME
HEI
GH
T+
21/
4”[5
7]
3/4” [19]
OV
ERA
LLFR
AM
EH
EIG
HT
+1-
1/2”
OV
ERA
LLRO
UG
HO
PEN
ING
+3/
4”
OV
ERA
LLU
NIT
HEI
GH
T(B
ASI
CU
NIT
FRA
ME
HEI
GH
T+
11/
2”[3
8]
BASI
CU
NIT
FRA
ME
HEI
GH
T
3/4” [19]3/4” [19]
Vertical Masonry Opening will be 1/2” [13]larger than the Overall Unit Height.
BRICKMOULD & SILLNOSE
3/4” [19]
Exterior of Wall
4 Wide Bow Shown4, 5 & 6 WIDE BOWS
Rough Opening ismeasured from thepoint the frame intersectsthe exterior wall.
Rough Opening
3/8” [10]
3/4” [19]
Vertical Masonry Opening will be 1/2” [13]larger than the Overall Unit Height.
STANDARD OFFERING
3/4” [19]
Exterior of Wall
Rough Opening ismeasured from thepoint the frame intersectsthe jamb aligner & exteriorwall.
Rough Opening
3/8” [10]
VERTICAL ROUGH OPENING HORIZONTAL ROUGH OPENING
1 25/32” [45]
1 13/16” [46]
SEATBOARD
HEADBOARD
SEATBOARD
HEADBOARD
30_ & 45_ BAYS45_ Bay Shown
without trim
Continued on next page
BAY & BOW WINDOW TRIM OPTIONSThe standard offering for wood bay & bow windows is ’frame only’, brickmould and subsill, subsillonly, and brickmould on all sides. Other trim options subject to approval. Rough & Masonryopenings remain consistent with all trim options.
OV
ERA
LLRO
UG
HO
PEN
ING
+3/
4”
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-66
BAY & BOW WINDOW ROUGH OPENINGS
Rough Opening typical for all UnitsRough Opening typical for all Units
OV
ERA
LLFR
AM
EH
EIG
HT
+1-
1/2”
OV
ERA
LLRO
UG
HO
PEN
ING
+3/
4”
OV
ERA
LLU
NIT
HEI
GH
T(B
ASI
CU
NIT
FRA
ME
HEI
GH
T+
11/
2”[3
8]
BASI
CU
NIT
FRA
ME
HEI
GH
T
3/4” [19]
Exterior of Wall
4 Wide Bow Shown
4, 5 & 6 WIDE BOWS
Rough Opening ismeasured from thepoint the frame intersectsthe exterior wall.
Rough Opening
3/8” [10]
3/4” [19]
Vertical Masonry Opening will be 1/2” [13]larger than the Overall Unit Height.
NO TRIM
3/4” [19]
Exterior of Wall
Rough Opening ismeasured from thepoint the frame intersectsthe jamb aligner & exteriorwall.
Rough Opening
3/8” [10]
VERTICAL ROUGH OPENING HORIZONTAL ROUGH OPENING
SEATBOARD
HEADBOARD
30_ & 45_ BAYS
45_ Bay Shownwithout trim
BAY & BOW WINDOW TRIM OPTIONSThe standard offering for clad bay & bow windows is ’frame only’ and brickmould and sillnose. Other trim options subject to approval.Rough & Masonry openings remain consistent with all trim options.
Premium Wood
Siteline EX Clad Casement Windows
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-67
30_ ANGLE BAY UNIT
Gla
ssSi
ze
Day
light
Ope
ning
Sash
Size
Uni
tSi
ze
1/2”
1 9/16”
15/16”
15/16”
1 9/16”
1/2”
Ove
rall
Fram
eH
eigh
t+
1-1/
2”
Ove
rall
Roug
hO
peni
ng+
3/4”
4 3/16”1 3/16” 2 7/8”
7/16”2 7/16”
1 9/16”15/16”
4 3/16”
7/16”1 9/16”15/16”
2 1/2”2 15/16”
1 3/16”
VERTICAL SECTION
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-68
30_ ANGLE BAY UNIT
Daylight Opening
Glass Size
Sash Size
1 9/16” 1/2”
1/2”
1 9/16”
HORIZONTAL SECTION
1 9/16”
1/2”
1 5/8”
Sash Size
Glass Size
Daylight Opening
Unit Size
Rough Opening
Seatboard Size
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-69
45_ ANGLE BAY UNIT
Gla
ssSi
ze
Day
light
Ope
ning
Sash
Size
Uni
tSi
ze
1/2”
1 9/16”
15/16”
15/16”
1 9/16”
1/2”
Ove
rall
Fram
eH
eigh
t+
1-1/
2”
Ove
rall
Roug
hO
peni
ng+
3/4”
4 3/16”1 3/16” 2 7/8”
7/16”2 7/16”
1 9/16”15/16”
4 3/16”
7/16”1 9/16”15/16”
2 1/2”2 15/16”
1 3/16”
VERTICAL SECTION
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-70
45_ ANGLE BAY UNIT
Daylight Opening
Glass Size
Sash Size
1/2”1 9/16”
1/2”
1 9/16”
HORIZONTAL SECTION
1/2”
1 9/16”
2 1/8”
Sash Size
Glass Size
Daylight Opening
Unit Size
Rough Opening
Seatboard
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-71
BOW UNIT
Gla
ssSi
ze
Day
light
Ope
ning
Sash
Size
Uni
tSi
ze
1/2”
1 9/16”
15/16”
15/16”
1 9/16”
1/2”
Ove
rall
Fram
eH
eigh
t+
1-1/
2”
Ove
rall
Roug
hO
peni
ng+
3/4”
4 3/16”1 3/16” 2 7/8”
7/16”2 7/16”
1 9/16”15/16”
4 3/16”
7/16”1 9/16”15/16”
2 1/2”2 15/16”
1 3/16”
VERTICAL SECTION
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-72
BOW UNIT - 3-WIDE
Daylight Opening
Glass Size
Sash Size
1/2”
1 9/16” 1/2”
1 9/16”
HORIZONTAL SECTION
1/2”
1 9/16”
13/16”
Sash Size
Glass Size
Daylight Opening
Unit Size
Seatboard
Frame Size
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-73
BOW UNIT - 4-WIDE
Daylight Opening
Glass Size
Sash Size
1/2”
1 9/16”1/2”
1 9/16”
Daylight Opening
Glass Size
Sash Size
1/2”
1 9/16”
1/2”
1 9/16”
HORIZONTAL SECTION
1”
Unit Size
Rough Opening
Seatboard
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-74
BOW UNIT - 5-WIDE
Glass Size
Sash Size
1/2”
1 9/16”1/2”
1 9/16”
Daylight
Glass Size
Sash Size
1/2”
1 9/16”1/2”
1 9/16”
HORIZONTAL SECTION
1/2”
1 9/16”
1 1/4”
Sash Size
Glass Size
Daylight Opening
Unit Size
Seatboard
Frame Size
Opening
DaylightOpening
Premium Wood
Siteline EX Clad Casement Windows
SCALE: 3” = 1’
Architectural Detail ManualOctober 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-75