BEFORE YOU BEGIN 1191502-X2-A 1 1191502-X2-A 4 15136X-S หัวกอกลงอางอาบน้ำ 7098X 15136X หัวกอกลงอางอาบน้ำ 15136X-S หัวกอกลงอางอาบน้ำ 7098X 15136X หัวกอกลงอางอาบน้ำ ROUGH-IN DIMENSIONS INSTALLATION INSTRUCTIONS ขอแนะนําการติดตั้ง Bath Spout Bath Spout กอนเริ่มการติดตั้ง ขอมูลในคูมือนี้มาจากขอมูลผลิตภัณฑลาสุดที่มีอยูในชวงเวลาการ จัดพิมพ บริษัทฯขอสงวนสิทธิ์ในการเปลี่ยนแปลงขอมูลผลิตภัณฑ บรรจุภัณฑที่มีอยูโดยมิตองแจงใหทราบลวงหนา คูมือนี้มีขอมูลสำคัญ โปรดมอบเอกสารใหกับเจาของผลิตภัณฑ ขอสังเกต: 1. ปดวาลวนํ้าทำความสะอาดทอนํ้าดี เพื่อขจัดเศษสิ่งสกปรกตางๆ ระยะการติดตั้ง SERVICE PARTS อุปกรณประกอบและอะไหล **ระบุรหัสวัสดุเคลือบผิว/สีในการสั่งซื้อผลิตภัณฑ **Color code must be specified when ordering Call Center: +(66) 2204 6222 e-mail: [email protected]All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. Please leave these instructions for the consumer. They contain important information. NOTES: 1. Flush the water supply pipes thoroughly to remove debris. 2. Shut off the water supplies to the fitting. 3. Observe all local plumbing and building codes. หัวกอกลงอางอาบน้ำ 2. ปดวาลวทางน้ำเขา 3. ตรวจสอบระบบสุขาภิบาล หัวกอกลงอางอาบน้ำ 7098X 15136X 15136X-S 121 126 140 Ø66 G1/2˝ 60 G1/2˝ Ø64 G1/2˝ Fringe of bath ขอบอางอาบน้ำ 102 153 136 Fringe of bath ขอบอางอาบน้ำ 102 Fringe of bath ขอบอางอาบน้ำ 102 1140688 Streamer ปากกอก (Only for /สำหรับรุน 15136X-S เทานั้น) 865008 Nipple เกลียวทอน้ำดี (Only for /สำหรับรุน 15136X-S เทานั้น) 1184184 Nipple เกลียวทอน้ำดี (Only for /สำหรับรุน 15136X & 7098X เทานั้น)
2
Embed
SERVICE PARTS หัวก อกลงอ างอาบน้ำ INSTALLATION ...tech.kohlerthai.com/upload/Technical/x2_170325220920.pdfnipple to extend 98 mm beyond the finished
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.2. Shut off the water supplies to the fitting.3. Observe all local plumbing and building codes.
หัวกอกลงอางอาบน้ำ
2. ปดวาลวทางน้ำเขา3. ตรวจสอบระบบสุขาภิบาล
หัวกอกลงอางอาบน้ำ
7098X15136X
15136X-S
121126
140
Ø66
G1/2˝
60 G1/2˝
Ø64
G1/2˝
Fringe of bath
ขอบอางอาบน้ำ
102
153
136
Fringe of bath ขอบอางอาบน้ำ
102
Fringe of bath
ขอบอางอาบน้ำ
102
1140688Streamerปากกอก(Only for /สำหรับรุน 15136X-S เทานั้น)
865008Nippleเกลียวทอน้ำดี(Only for /สำหรับรุน 15136X-S เทานั้น)
1184184Nippleเกลียวทอน้ำดี(Only for /สำหรับรุน 15136X & 7098X เทานั้น)
1191502-X2-A 3
1191502-X2-A 2
INSTALLATION
INSTALLATION CHECKOUTทดสอบการติดตั้ง
การติดตั้ง
CARE AND CLEANING
For best results, keep the following in mind when caring for your product: • Always test your cleaning solution on an inconspicuous area before applying to the entire surface. • Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and dry any overspray that lands on nearby surfaces. • Do not allow cleaners to soak on surfaces.• Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring pad to clean surfaces.• The ideal cleaning technique is to rinse thoroughly and blot dry any water from the surface after each use.
Open the drain. Turn on the main water supply and check for leaks. Repair as required.
Only For 7098X & 15136X
Apply tape or sealant to the R1/2" nipple(1) threads. Install the R1/2" nipple to extend 98 mm beyond the finished wall. Flush hot and cold water through the spout for one minute.
Apply a ring of plumbers putty or sealant to the spout(2) base, carefully thread the spout onto the nipple with a strap wrench. Remove any excess putty or sealant.
Only For 15136X-S
Apply tape or sealant to the slip-fit spout nipple(3) threads. Install the nipple to extend 38~50mm beyond the finished wall. Flush hot and cold water through the spout for one minute.
Apply a ring of plumbers putty or sealant to the spout(4) base, adjust the spout downwards, and carefully tighten the setscrew(5) in the bottom of the spout. Remove any excess putty or sealant.